I noticed that for 2.4.0-test11 there is no help
for CONFIG_TOSHIBA, although there is for 2.2.17.
The following patch borrows the words for CONFIG_TOSHIBA
from the 2.2.17 Documentation/Configure.help, dropping
an extraneous "the" from the first line.
This patch applies to 2.4.0-test11.
Steven
diff -u linux/Documentation/Configure.help.orig \
linux/Documentation/Configure.help
--- linux/Documentation/Configure.help.orig Mon Nov 20 18:26:27 2000
+++ linux/Documentation/Configure.help Mon Nov 20 18:26:46 2000
@@ -13420,6 +13420,17 @@
module, say M here and read Documentation/modules.txt. Most people
will say N.
+Toshiba Laptop support
+CONFIG_TOSHIBA
+ If you intend to run this kernel on a Toshiba portable say yes
+ here. This adds a driver to safely access the System Management
+ Mode of the CPU on Toshiba portables. The System Management Mode
+ is used to set the BIOS and power saving options on Toshiba portables.
+
+ For information on utilities to make use of this driver see the
+ Toshiba Linux utilities website at:
+ http://www.buzzard.org.uk/toshiba/
+
/dev/cpu/microcode - Intel P6 CPU microcode support
CONFIG_MICROCODE
If you say Y here and also to "/dev file system support" in the
>>>>> "Steven" == Steven Cole <[email protected]> writes:
Steven> I noticed that for 2.4.0-test11 there is no help for
Steven> CONFIG_TOSHIBA, although there is for 2.2.17.
Steven> The following patch borrows the words for CONFIG_TOSHIBA from
Steven> the 2.2.17 Documentation/Configure.help, dropping an
Steven> extraneous "the" from the first line.
Would probably be a good idea to name the config option
CONFIG_TOSHIBA_LAPTOP_MGMT or something to avoid the possibility of a
conflict in case someone else special cases some other Toshiba thing.
Jes
Steven Cole <[email protected]> writes:
> I noticed that for 2.4.0-test11 there is no help
> for CONFIG_TOSHIBA, although there is for 2.2.17.
>
> The following patch borrows the words for CONFIG_TOSHIBA
> from the 2.2.17 Documentation/Configure.help, dropping
> an extraneous "the" from the first line.
>
> This patch applies to 2.4.0-test11.
>
you can apply this too:
--- linux/Documentation/Configure.help.orig Wed Sep 27 03:37:40 2000
+++ linux/Documentation/Configure.help Wed Sep 27 03:39:02 2000
@@ -268,6 +268,11 @@
Most normal users won't need the RAM disk functionality, and can
thus say N here.
+Default RAM disk size
+CONFIG_BLK_DEV_RAM_SIZE
+ The default value is 4096. Only change this if you know what are
+ you doing. If you are using IBM S/390, then set this to 8192.
+
Initial RAM disk (initrd) support
CONFIG_BLK_DEV_INITRD
The initial RAM disk is a RAM disk that is loaded by the boot loader
@@ -14209,6 +14209,11 @@
driver as a module you have to specify the MPU I/O base address with
the parameter 'mpu_base=0xNNN'.
+C-Media PCI (CMI8338/8378)
+CONFIG_SOUND_CMPCI
+ Say Y or M if you have a PCI sound card using the CMI8338
+ or the CMI8378 chip.set.
+
Creative EMU10K1 based PCI sound cards
CONFIG_SOUND_EMU10K1
Say Y or M if you have a PCI sound card using the EMU10K1
--- linux/Documentation/sound/CMI8330.orig Wed Sep 27 03:36:34 2000
+++ linux/Documentation/sound/CMI8330 Wed Sep 27 03:37:09 2000
@@ -57,7 +57,7 @@
------------------------------------------
Stefan Laudat <[email protected]>
-[Note: The CMI 8338 is unrelated and right now unsupported]
+[Note: The CMI 8338 is unrelated and is supported by cmpcpi.o]
In order to use CMI8330 under Linux you just have to use a proper isapnp.conf, a good isapnp and a little bit of patience. I use isapnp 1.17, but