2023-06-05 05:40:19

by Sridharan S N

Subject: [PATCH V2 1/2] arm64: dts: qcom: ipq5332: enable GPIO based LEDs and Buttons

Add support for wlan-2g LED on GPIO 36 and wps buttons on GPIO 35.

Signed-off-by: Sridharan S N <[email protected]>
---
Changes in V2:
- Used the hypen in node name instead of underscore
- Dropped the status property

arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 42 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts | 42 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts | 42 +++++++++++++++++++++
3 files changed, 126 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
index 3af1d5556950..5bd4ff3ad86b 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
+++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
@@ -7,6 +7,8 @@

/dts-v1/;

+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "ipq5332.dtsi"

/ {
@@ -20,6 +22,32 @@
chosen {
stdout-path = "serial0";
};
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&gpio_keys_default>;
+ pinctrl-names = "default";
+
+ button-wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&gpio_leds_default>;
+ pinctrl-names = "default";
+
+ led-0 {
+ gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+ };
};

&blsp1_uart0 {
@@ -57,6 +85,20 @@
/* PINCTRL */

&tlmm {
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio35";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ gpio_leds_default: gpio-leds-default-state {
+ pins = "gpio36";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
i2c_1_pins: i2c-1-state {
pins = "gpio29", "gpio30";
function = "blsp1_i2c0";
diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
index bcf3b31c20e3..36cbebb75c48 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
+++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
@@ -7,6 +7,8 @@

/dts-v1/;

+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "ipq5332.dtsi"

/ {
@@ -20,6 +22,32 @@
chosen {
stdout-path = "serial0";
};
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&gpio_keys_default>;
+ pinctrl-names = "default";
+
+ button-wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&gpio_leds_default>;
+ pinctrl-names = "default";
+
+ led-0 {
+ gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+ };
};

&blsp1_uart0 {
@@ -71,6 +99,20 @@
/* PINCTRL */

&tlmm {
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio35";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ gpio_leds_default: gpio-leds-default-state {
+ pins = "gpio36";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
i2c_1_pins: i2c-1-state {
pins = "gpio29", "gpio30";
function = "blsp1_i2c0";
diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
index 3b6a5cb8bf07..2d27f48f00c0 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
+++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
@@ -7,6 +7,8 @@

/dts-v1/;

+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "ipq5332.dtsi"

/ {
@@ -20,6 +22,32 @@
chosen {
stdout-path = "serial0";
};
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&gpio_keys_default>;
+ pinctrl-names = "default";
+
+ button-wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&gpio_leds_default>;
+ pinctrl-names = "default";
+
+ led-0 {
+ gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+ };
};

&blsp1_uart0 {
@@ -64,6 +92,20 @@
/* PINCTRL */

&tlmm {
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio35";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ gpio_leds_default: gpio-leds-default-state {
+ pins = "gpio36";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
sdc_default_state: sdc-default-state {
clk-pins {
pins = "gpio13";
--
2.17.1

2023-06-06 13:06:09

by Konrad Dybcio

Subject: Re: [PATCH V2 1/2] arm64: dts: qcom: ipq5332: enable GPIO based LEDs and Buttons

On 5.06.2023 07:29, Sridharan S N wrote:
> Add support for wlan-2g LED on GPIO 36 and wps buttons on GPIO 35.
>
> Signed-off-by: Sridharan S N <[email protected]>
> ---
> Changes in V2:
> - Used the hypen in node name instead of underscore
> - Dropped the status property
>
> arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 42 +++++++++++++++++++++
> arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts | 42 +++++++++++++++++++++
> arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts | 42 +++++++++++++++++++++
> 3 files changed, 126 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
> index 3af1d5556950..5bd4ff3ad86b 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
> @@ -7,6 +7,8 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> #include "ipq5332.dtsi"
>
> / {
> @@ -20,6 +22,32 @@
> chosen {
> stdout-path = "serial0";
> };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-0 = <&gpio_keys_default>;
> + pinctrl-names = "default";
> +
> + button-wps {
> + label = "wps";
> + linux,code = <KEY_WPS_BUTTON>;
> + gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
> + linux,input-type = <1>;
> + debounce-interval = <60>;
> + };
> + };
All of these changes seem very repetetive.. Are these devboards based
on a common design? Maybe ipq5332-rdp-common.dtsi would be beneficial
here?

Konrad
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&gpio_leds_default>;
> + pinctrl-names = "default";
> +
> + led-0 {
> + gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> + };
> };
>
> &blsp1_uart0 {
> @@ -57,6 +85,20 @@
> /* PINCTRL */
>
> &tlmm {
> + gpio_keys_default: gpio-keys-default-state {
> + pins = "gpio35";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +
> + gpio_leds_default: gpio-leds-default-state {
> + pins = "gpio36";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +
> i2c_1_pins: i2c-1-state {
> pins = "gpio29", "gpio30";
> function = "blsp1_i2c0";
> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
> index bcf3b31c20e3..36cbebb75c48 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
> @@ -7,6 +7,8 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> #include "ipq5332.dtsi"
>
> / {
> @@ -20,6 +22,32 @@
> chosen {
> stdout-path = "serial0";
> };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-0 = <&gpio_keys_default>;
> + pinctrl-names = "default";
> +
> + button-wps {
> + label = "wps";
> + linux,code = <KEY_WPS_BUTTON>;
> + gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
> + linux,input-type = <1>;
> + debounce-interval = <60>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&gpio_leds_default>;
> + pinctrl-names = "default";
> +
> + led-0 {
> + gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> + };
> };
>
> &blsp1_uart0 {
> @@ -71,6 +99,20 @@
> /* PINCTRL */
>
> &tlmm {
> + gpio_keys_default: gpio-keys-default-state {
> + pins = "gpio35";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +
> + gpio_leds_default: gpio-leds-default-state {
> + pins = "gpio36";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +
> i2c_1_pins: i2c-1-state {
> pins = "gpio29", "gpio30";
> function = "blsp1_i2c0";
> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
> index 3b6a5cb8bf07..2d27f48f00c0 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
> @@ -7,6 +7,8 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> #include "ipq5332.dtsi"
>
> / {
> @@ -20,6 +22,32 @@
> chosen {
> stdout-path = "serial0";
> };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-0 = <&gpio_keys_default>;
> + pinctrl-names = "default";
> +
> + button-wps {
> + label = "wps";
> + linux,code = <KEY_WPS_BUTTON>;
> + gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
> + linux,input-type = <1>;
> + debounce-interval = <60>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&gpio_leds_default>;
> + pinctrl-names = "default";
> +
> + led-0 {
> + gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> + };
> };
>
> &blsp1_uart0 {
> @@ -64,6 +92,20 @@
> /* PINCTRL */
>
> &tlmm {
> + gpio_keys_default: gpio-keys-default-state {
> + pins = "gpio35";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +
> + gpio_leds_default: gpio-leds-default-state {
> + pins = "gpio36";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +
> sdc_default_state: sdc-default-state {
> clk-pins {
> pins = "gpio13";

2023-06-09 10:44:12

by Sridharan S N

Subject: Re: [PATCH V2 1/2] arm64: dts: qcom: ipq5332: enable GPIO based LEDs and Buttons

On 6/6/2023 6:27 PM, Konrad Dybcio wrote:
>
> On 5.06.2023 07:29, Sridharan S N wrote:
>> Add support for wlan-2g LED on GPIO 36 and wps buttons on GPIO 35.
>>
>> Signed-off-by: Sridharan S N <[email protected]>
>> ---
>> Changes in V2:
>> - Used the hypen in node name instead of underscore
>> - Dropped the status property
>>
>> arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 42 +++++++++++++++++++++
>> arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts | 42 +++++++++++++++++++++
>> arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts | 42 +++++++++++++++++++++
>> 3 files changed, 126 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
>> index 3af1d5556950..5bd4ff3ad86b 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
>> +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
>> @@ -7,6 +7,8 @@
>>
>> /dts-v1/;
>>
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> #include "ipq5332.dtsi"
>>
>> / {
>> @@ -20,6 +22,32 @@
>> chosen {
>> stdout-path = "serial0";
>> };
>> +
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> + pinctrl-0 = <&gpio_keys_default>;
>> + pinctrl-names = "default";
>> +
>> + button-wps {
>> + label = "wps";
>> + linux,code = <KEY_WPS_BUTTON>;
>> + gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
>> + linux,input-type = <1>;
>> + debounce-interval = <60>;
>> + };
>> + };
> All of these changes seem very repetetive.. Are these devboards based
> on a common design? Maybe ipq5332-rdp-common.dtsi would be beneficial
> here?
Will move all the common nodes to common dtsi in the next patch
> Thanks,
Sridharan
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&gpio_leds_default>;
> + pinctrl-names = "default";
> +
> + led-0 {
> + gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> + };
> };
>
> &blsp1_uart0 {
> @@ -57,6 +85,20 @@
> /* PINCTRL */
>
> &tlmm {
> + gpio_keys_default: gpio-keys-default-state {
> + pins = "gpio35";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +
> + gpio_leds_default: gpio-leds-default-state {
> + pins = "gpio36";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +
> i2c_1_pins: i2c-1-state {
> pins = "gpio29", "gpio30";
> function = "blsp1_i2c0";
> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
> index bcf3b31c20e3..36cbebb75c48 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
> @@ -7,6 +7,8 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> #include "ipq5332.dtsi"
>
> / {
> @@ -20,6 +22,32 @@
> chosen {
> stdout-path = "serial0";
> };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-0 = <&gpio_keys_default>;
> + pinctrl-names = "default";
> +
> + button-wps {
> + label = "wps";
> + linux,code = <KEY_WPS_BUTTON>;
> + gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
> + linux,input-type = <1>;
> + debounce-interval = <60>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&gpio_leds_default>;
> + pinctrl-names = "default";
> +
> + led-0 {
> + gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> + };
> };
>
> &blsp1_uart0 {
> @@ -71,6 +99,20 @@
> /* PINCTRL */
>
> &tlmm {
> + gpio_keys_default: gpio-keys-default-state {
> + pins = "gpio35";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +
> + gpio_leds_default: gpio-leds-default-state {
> + pins = "gpio36";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +
> i2c_1_pins: i2c-1-state {
> pins = "gpio29", "gpio30";
> function = "blsp1_i2c0";
> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
> index 3b6a5cb8bf07..2d27f48f00c0 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
> @@ -7,6 +7,8 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> #include "ipq5332.dtsi"
>
> / {
> @@ -20,6 +22,32 @@
> chosen {
> stdout-path = "serial0";
> };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-0 = <&gpio_keys_default>;
> + pinctrl-names = "default";
> +
> + button-wps {
> + label = "wps";
> + linux,code = <KEY_WPS_BUTTON>;
> + gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
> + linux,input-type = <1>;
> + debounce-interval = <60>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-0 = <&gpio_leds_default>;
> + pinctrl-names = "default";
> +
> + led-0 {
> + gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> + };
> };
>
> &blsp1_uart0 {
> @@ -64,6 +92,20 @@
> /* PINCTRL */
>
> &tlmm {
> + gpio_keys_default: gpio-keys-default-state {
> + pins = "gpio35";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +
> + gpio_leds_default: gpio-leds-default-state {
> + pins = "gpio36";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +
> sdc_default_state: sdc-default-state {
> clk-pins {
> pins = "gpio13";