Add device tree node for pm8226 GPIOs and support for the Samsung Galaxy
Tab 4 10.1 (SM-T530) tablet which is based on apq8026.
---
Changes in v2:
- Change codename to matisse-wifi
- Remove msm-id, not needed when lk2nd is used
- Remove unused labels from reserved memory regions
- Rename muic node
- Rename pm8226 gpio node
Matti Lehtimäki (3):
ARM: dts: qcom: pm8226: Add node for the GPIOs
dt-bindings: arm: qcom: Document samsung,matisse-wifi device
ARM: dts: qcom: Add support for Samsung Galaxy Tab 4 10.1 (SM-T530)
.../devicetree/bindings/arm/qcom.yaml | 1 +
arch/arm/boot/dts/Makefile | 1 +
.../dts/qcom-apq8026-samsung-matisse-wifi.dts | 469 ++++++++++++++++++
arch/arm/boot/dts/qcom-pm8226.dtsi | 10 +
4 files changed, 481 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
--
2.34.1
The PM8226 provides 8 GPIOs. Add a node to support them.
Signed-off-by: Matti Lehtimäki <[email protected]>
---
Changes in v2:
- Rename pm8226 gpio node
---
arch/arm/boot/dts/qcom-pm8226.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-pm8226.dtsi b/arch/arm/boot/dts/qcom-pm8226.dtsi
index 9b7d9d04ded6..0c10fa16a0f3 100644
--- a/arch/arm/boot/dts/qcom-pm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8226.dtsi
@@ -90,6 +90,16 @@ pm8226_mpps: mpps@a000 {
interrupt-controller;
#interrupt-cells = <2>;
};
+
+ pm8226_gpios: gpio@c000 {
+ compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pm8226_gpios 0 0 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
};
pm8226_1: pm8226@1 {
--
2.34.1
Add a device tree for the Samsung Galaxy Tab 4 10.1 (SM-T530) wifi tablet
based on the apq8026 platform.
Currently supported are accelerometer sensor, hall sensor,
internal storage, physical buttons (power & volume), screen
(based on simple-framebuffer set up by the bootloader) sdcard,
touchscreen and USB.
Signed-off-by: Matti Lehtimäki <[email protected]>
---
Changes in v2:
- Change codename to matisse-wifi
- Remove msm-id, not needed when lk2nd is used
- Remove unused labels from reserved memory regions
- Rename muic node
---
arch/arm/boot/dts/Makefile | 1 +
.../dts/qcom-apq8026-samsung-matisse-wifi.dts | 469 ++++++++++++++++++
2 files changed, 470 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 5112f493f494..8bac4f4f8656 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1010,6 +1010,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8016-sbc.dtb \
qcom-apq8026-asus-sparrow.dtb \
qcom-apq8026-lg-lenok.dtb \
+ qcom-apq8026-samsung-matisse-wifi.dtb \
qcom-apq8060-dragonboard.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
new file mode 100644
index 000000000000..621e0a337724
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
@@ -0,0 +1,469 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+#include <dt-bindings/input/input.h>
+
+/delete-node/ &smem_region;
+
+/ {
+ model = "Samsung Galaxy Tab 4 10.1";
+ compatible = "samsung,matisse-wifi", "qcom,apq8026";
+ chassis-type = "tablet";
+
+ aliases {
+ mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+ mmc1 = &sdhc_2; /* SDC2 SD card slot */
+ display0 = &framebuffer0;
+ };
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ stdout-path = "display0";
+
+ framebuffer0: framebuffer@3200000 {
+ compatible = "simple-framebuffer";
+ reg = <0x3200000 0x800000>;
+ width = <1280>;
+ height = <800>;
+ stride = <(1280 * 3)>;
+ format = "r8g8b8";
+ };
+ };
+
+ gpio-hall-sensor {
+ compatible = "gpio-keys";
+
+ event-hall-sensor {
+ label = "Hall Effect Sensor";
+ gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ interrupts = <&tlmm 110 IRQ_TYPE_EDGE_FALLING>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ debounce-interval = <15>;
+ wakeup-source;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ key-home {
+ label = "Home";
+ gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOMEPAGE>;
+ debounce-interval = <15>;
+ };
+
+ key-volume-down {
+ label = "Volume Down";
+ gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ debounce-interval = <15>;
+ };
+
+ key-volume-up {
+ label = "Volume Up";
+ gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ debounce-interval = <15>;
+ };
+ };
+
+ i2c-muic {
+ compatible = "i2c-gpio";
+ sda-gpios = <&tlmm 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&tlmm 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&muic_i2c_default_state>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ muic: usb-switch@25 {
+ compatible = "siliconmitus,sm5502-muic";
+ reg = <0x25>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&muic_int_default_state>;
+ };
+ };
+
+ reg_tsp_1p8v: regulator-tsp-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "tsp_1p8v";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tsp_en_default_state>;
+ };
+
+ reg_tsp_3p3v: regulator-tsp-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "tsp_3p3v";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tsp_en1_default_state>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@3200000 {
+ reg = <0x3200000 0x800000>;
+ no-map;
+ };
+
+ mpss@8400000 {
+ reg = <0x08400000 0x1f00000>;
+ no-map;
+ };
+
+ mba@a300000 {
+ reg = <0x0a300000 0x100000>;
+ no-map;
+ };
+
+ reserved@cb00000 {
+ reg = <0x0cb00000 0x700000>;
+ no-map;
+ };
+
+ wcnss@d200000 {
+ reg = <0x0d200000 0x700000>;
+ no-map;
+ };
+
+ adsp@d900000 {
+ reg = <0x0d900000 0x1800000>;
+ no-map;
+ };
+
+ venus@f100000 {
+ reg = <0x0f100000 0x500000>;
+ no-map;
+ };
+
+ smem_region: smem@fa00000 {
+ reg = <0xfa00000 0x100000>;
+ no-map;
+ };
+
+ reserved@fb00000 {
+ reg = <0x0fb00000 0x260000>;
+ no-map;
+ };
+
+ rfsa@fd60000 {
+ reg = <0x0fd60000 0x20000>;
+ no-map;
+ };
+
+ rmtfs@fd80000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0fd80000 0x180000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ };
+ };
+};
+
+&blsp1_i2c2 {
+ status = "okay";
+
+ accelerometer@1d {
+ compatible = "st,lis2hh12";
+ reg = <0x1d>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&accel_int_default_state>;
+
+ st,drdy-int-pin = <1>;
+
+ vdd-supply = <&pm8226_l19>;
+ vddio-supply = <&pm8226_lvs1>;
+ };
+};
+
+&blsp1_i2c5 {
+ status = "okay";
+
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tsp_int_rst_default_state>;
+
+ reset-gpios = <&pm8226_gpios 6 GPIO_ACTIVE_LOW>;
+
+ vdd-supply = <®_tsp_1p8v>;
+ vdda-supply = <®_tsp_3p3v>;
+ };
+};
+
+&rpm_requests {
+ pm8226-regulators {
+ compatible = "qcom,rpm-pm8226-regulators";
+
+ pm8226_s3: s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pm8226_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_s5: s5 {
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ };
+
+ pm8226_l1: l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pm8226_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8226_l3: l3 {
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1337500>;
+ regulator-always-on;
+ };
+
+ pm8226_l4: l4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8226_l5: l5 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8226_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ pm8226_l7: l7 {
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <1850000>;
+ };
+
+ pm8226_l8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ pm8226_l9: l9 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pm8226_l10: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l14: l14 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ };
+
+ pm8226_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8226_l16: l16 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3350000>;
+ };
+
+ pm8226_l17: l17 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ regulator-always-on;
+ };
+
+ pm8226_l18: l18 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_l19: l19 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ pm8226_l20: l20 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ pm8226_l21: l21 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_l22: l22 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ pm8226_l23: l23 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8226_l24: l24 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ pm8226_l25: l25 {
+ regulator-min-microvolt = <1775000>;
+ regulator-max-microvolt = <2125000>;
+ };
+
+ pm8226_l26: l26 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pm8226_l27: l27 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8226_l28: l28 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8226_lvs1: lvs1 {};
+ };
+};
+
+&sdhc_1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8226_l17>;
+ vqmmc-supply = <&pm8226_l6>;
+
+ bus-width = <8>;
+ non-removable;
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ vmmc-supply = <&pm8226_l18>;
+ vqmmc-supply = <&pm8226_l21>;
+
+ bus-width = <8>;
+ cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+};
+
+&tlmm {
+ accel_int_default_state: accel-int-default-state {
+ pins = "gpio54";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ muic_i2c_default_state: muic-i2c-default-state {
+ pins = "gpio14", "gpio15";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ muic_int_default_state: muic-int-default-state {
+ pins = "gpio67";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tsp_en_default_state: tsp-en-default-state {
+ pins = "gpio31";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tsp_en1_default_state: tsp-en1-default-state {
+ pins = "gpio73";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tsp_int_rst_default_state: tsp-int-rst-default-state {
+ pins = "gpio17";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+};
+
+&usb {
+ status = "okay";
+ extcon = <&muic>, <&muic>;
+};
+
+&usb_hs_phy {
+ extcon = <&muic>;
+ v1p8-supply = <&pm8226_l10>;
+ v3p3-supply = <&pm8226_l20>;
+};
--
2.34.1
Add binding documentation for Samsung Galaxy Tab 4 10.1 (2014) wifi
tablet which is based on Snapdragon 400 (apq8026) SoC.
Signed-off-by: Matti Lehtimäki <[email protected]>
---
Changes in v2:
- Change codename to matisse-wifi
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 5c06d1bfc046..5b5b0e0ee8e7 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -104,6 +104,7 @@ properties:
- enum:
- asus,sparrow
- lg,lenok
+ - samsung,matisse-wifi
- const: qcom,apq8026
- items:
--
2.34.1
On 22.07.2022 01:02, Matti Lehtimäki wrote:
> Add a device tree for the Samsung Galaxy Tab 4 10.1 (SM-T530) wifi tablet
> based on the apq8026 platform.
>
> Currently supported are accelerometer sensor, hall sensor,
> internal storage, physical buttons (power & volume), screen
> (based on simple-framebuffer set up by the bootloader) sdcard,
> touchscreen and USB.
>
> Signed-off-by: Matti Lehtimäki <[email protected]>
> ---
> Changes in v2:
> - Change codename to matisse-wifi
> - Remove msm-id, not needed when lk2nd is used
> - Remove unused labels from reserved memory regions
> - Rename muic node
> ---
> arch/arm/boot/dts/Makefile | 1 +
> .../dts/qcom-apq8026-samsung-matisse-wifi.dts | 469 ++++++++++++++++++
> 2 files changed, 470 insertions(+)
> create mode 100644 arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 5112f493f494..8bac4f4f8656 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1010,6 +1010,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
> qcom-apq8016-sbc.dtb \
> qcom-apq8026-asus-sparrow.dtb \
> qcom-apq8026-lg-lenok.dtb \
> + qcom-apq8026-samsung-matisse-wifi.dtb \
> qcom-apq8060-dragonboard.dtb \
> qcom-apq8064-cm-qs600.dtb \
> qcom-apq8064-ifc6410.dtb \
> diff --git a/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
> new file mode 100644
> index 000000000000..621e0a337724
> --- /dev/null
> +++ b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
> @@ -0,0 +1,469 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022, Matti Lehtimäki <[email protected]>
> + */
> +
> +/dts-v1/;
> +
> +#include "qcom-msm8226.dtsi"
> +#include "qcom-pm8226.dtsi"
> +#include <dt-bindings/input/input.h>
Hello!
I think generally dt-bindings includes go before the DTS ones.
> +
> +/delete-node/ &smem_region;
> +
> +/ {
> + model = "Samsung Galaxy Tab 4 10.1";
> + compatible = "samsung,matisse-wifi", "qcom,apq8026";
[...]
> +
> +&sdhc_2 {
> + status = "okay";
> +
> + vmmc-supply = <&pm8226_l18>;
> + vqmmc-supply = <&pm8226_l21>;
> +
> + bus-width = <8>;
I doubt this.. do you have downstream backing this up?
> + cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
> +};
Other than that, this looks good to me.
Konrad
On 22/07/2022 01:02, Matti Lehtimäki wrote:
> Add binding documentation for Samsung Galaxy Tab 4 10.1 (2014) wifi
> tablet which is based on Snapdragon 400 (apq8026) SoC.
>
> Signed-off-by: Matti Lehtimäki <[email protected]>
> ---
Acked-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof