Hi all...
I'm getting some proeblems and hangs with latest kernels.
I have two kind of problems, with ATA and with SATA-RAID.
SATA disks ata1-8 are part of a raid5 array exported via samba
(two promise controlers, 3 out of 4 ports used on each).
hde is an ATA disk for system root.
hde gives errors with 2.6.9 and -rc4-mm1. Also ata5 (SATA).
2.6.9-rc3-mm3 is working fine.
With 2.6.9-rc4-mm1, I get this messages:
Oct 18 19:31:54 nada kernel: Linux version 2.6.9-rc4-mm1 ([email protected]) (gcc version 3.4.1 (Mandrakelinux 10.1 3.4.1-4mdk)) #1 SMP Thu Oct 14 23:57:32 CEST 2004
...
Oct 18 19:31:54 nada kernel: VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
Oct 18 19:31:54 nada kernel: ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:DMA, hdf:pio
Oct 18 19:31:54 nada kernel: ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:DMA
Oct 18 19:31:54 nada kernel: Probing IDE interface ide2...
Oct 18 19:31:54 nada kernel: hde: Maxtor 6Y080L0, ATA DISK drive
Oct 18 19:31:54 nada kernel: ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
...
Oct 18 19:31:54 nada kernel: ata5: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003 88:407f
Oct 18 19:31:54 nada kernel: ata5: dev 0 ATA, max UDMA/133, 490234752 sectors: lba48
Oct 18 19:31:54 nada kernel: ata5: dev 0 configured for UDMA/133
Oct 18 19:31:54 nada kernel: scsi4 : sata_promise
...
Oct 18 19:31:54 nada kernel: Vendor: ATA Model: Maxtor 7Y250M0 Rev: YAR5
Oct 18 19:31:54 nada kernel: Type: Direct-Access ANSI SCSI revision: 05
...
Oct 18 19:31:54 nada kernel: sde: sde1
Oct 18 19:31:54 nada kernel: Attached scsi disk sde at scsi5, channel 0, id 0, lun 0
Oct 18 19:31:54 nada kernel: SCSI device sdf: 490234752 512-byte hdwr sectors (251000 MB)
Oct 18 19:31:54 nada kernel: SCSI device sdf: drive cache: write back
...
Oct 18 20:54:10 nada kernel: ata5: command timeout
Oct 18 20:54:30 nada kernel: hde: dma_timer_expiry: dma status == 0x24
Oct 18 20:54:40 nada kernel: hde: DMA interrupt recovery
Oct 18 20:54:40 nada kernel: hde: lost interrupt
<tons of similar messages>
...
With 2.6.9:
Oct 19 11:11:45 nada kernel: Linux version 2.6.9 ([email protected]) (gcc
...
Oct 19 13:07:03 nada kernel: ata5: command timeout
Oct 19 13:16:24 nada smb: smbd shutdown succeeded
Oct 19 13:16:24 nada nmbd[10910]: [2004/10/19 13:16:24, 0] nmbd/nmbd.c:terminate(54)
Oct 19 13:16:24 nada nmbd[10910]: Got SIGTERM: going down...
Oct 19 13:16:24 nada smb: nmbd shutdown succeeded
Any ideas ?
TIA
--
J.A. Magallon <jamagallon()able!es> \ Software is like sex:
werewolf!able!es \ It's better when it's free
Mandrakelinux release 10.1 (Community) for i586
Linux 2.6.9-rc4-mm1 (gcc 3.4.1 (Mandrakelinux 10.1 3.4.1-4mdk)) #4
On 2004.10.19, J.A. Magallon wrote:
> Hi all...
>
> I'm getting some proeblems and hangs with latest kernels.
> I have two kind of problems, with ATA and with SATA-RAID.
> SATA disks ata1-8 are part of a raid5 array exported via samba
> (two promise controlers, 3 out of 4 ports used on each).
> hde is an ATA disk for system root.
>
> hde gives errors with 2.6.9 and -rc4-mm1. Also ata5 (SATA).
> 2.6.9-rc3-mm3 is working fine.
>
> With 2.6.9-rc4-mm1, I get this messages:
>
Ahh. forgot to say that system gets locked after that,
sometimes just samba hangs, others the box is completely dead...
--
J.A. Magallon <jamagallon()able!es> \ Software is like sex:
werewolf!able!es \ It's better when it's free
Mandrakelinux release 10.1 (Community) for i586
Linux 2.6.9-rc4-mm1 (gcc 3.4.1 (Mandrakelinux 10.1 3.4.1-4mdk)) #4