Hi,
Here is another minor revision of my work.
In this version I added few (two) sysfs attributes for udev rules
One attribute is exported my mtd driver, and specifies if this is smartmedia or
xd card (its called "media_type")
Another attribute is exported by FTL, and it is extracted vendor name from the card CIS.
I added short common code to translation layer to allow such thing.
Tested this again on 256 byte/page nandsim device, and everything works as usual.
I don't think I will need to change anything major from now on.
Best regards,
Maxim Levitsky
This adds a driver for Ricoh xD card reader with PCI id 0x0852
Since the reader is a part of larger mulifunction chip, it
is hard to determine the correct model name. Might be R5C852.
Driver is complete, but bewere of the fact that some
(probably only type M) xD cards are 'fake' which means that
they have an on board CPU and expose emulated nand command set
These cards don't even store the oob area on the flash,
but generate it on the fly from something else.
Thus they demand to have proper values written in the oob area,
and therefore only useful with SmartMedia FTL.
Signed-off-by: Maxim Levitsky <[email protected]>
---
MAINTAINERS | 6 +
drivers/mtd/nand/Kconfig | 11 +
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/r822.c | 1105 +++++++++++++++++++++++++++++++++++++++++++++
drivers/mtd/nand/r822.h | 153 +++++++
include/linux/pci_ids.h | 2 +
6 files changed, 1278 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/nand/r822.c
create mode 100644 drivers/mtd/nand/r822.h
diff --git a/MAINTAINERS b/MAINTAINERS
index dd079bd..d553b96 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4574,6 +4574,12 @@ S: Maintained
F: Documentation/rfkill.txt
F: net/rfkill/
+RICOH SMARTMEDIA/XD DRIVER
+M: Maxim Levitsky <[email protected]>
+S: Maintained
+F: drivers/mtd/nand/r822.c
+F: drivers/mtd/nand/r822.h
+
RISCOM8 DRIVER
S: Orphan
F: Documentation/serial/riscom8.txt
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 13c1fb2..20803fa 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -113,6 +113,17 @@ config MTD_NAND_TS7250
config MTD_NAND_IDS
tristate
+config MTD_NAND_RICOH
+ tristate "Ricoh xD card reader"
+ default n
+ select MTD_SM_COMMON
+ help
+ Enable support for Ricoh xD card reader
+ You also need to enable ether
+ NAND SSFDC (SmartMedia) read only translation layer' or new
+ expermental, readwrite
+ 'SmartMedia/xD new translation layer'
+
config MTD_NAND_AU1550
tristate "Au1550/1200 NAND support"
depends on SOC_AU1200 || SOC_AU1550
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 09891f6..dc7c0bb 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -43,5 +43,6 @@ obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o
obj-$(CONFIG_MTD_NAND_W90P910) += w90p910_nand.o
obj-$(CONFIG_MTD_NAND_NOMADIK) += nomadik_nand.o
obj-$(CONFIG_MTD_NAND_BCM_UMI) += bcm_umi_nand.o nand_bcm_umi.o
+obj-$(CONFIG_MTD_NAND_RICOH) += r822.o
nand-objs := nand_base.o nand_bbt.o
diff --git a/drivers/mtd/nand/r822.c b/drivers/mtd/nand/r822.c
new file mode 100644
index 0000000..95a6bc0
--- /dev/null
+++ b/drivers/mtd/nand/r822.c
@@ -0,0 +1,1105 @@
+/*
+ * Copyright (C) 2009 - Maxim Levitsky
+ * driver for Ricoh xD readers
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/jiffies.h>
+#include <linux/workqueue.h>
+#include <linux/interrupt.h>
+#include <linux/pci_ids.h>
+#include <asm/byteorder.h>
+#include <linux/sched.h>
+#include "sm_common.h"
+#include "r822.h"
+
+
+static int enable_dma = 1;
+module_param(enable_dma, bool, S_IRUGO);
+MODULE_PARM_DESC(enable_dma, "Enable usage of DMA (default)");
+
+
+/* read register */
+static inline u8 r822_read_reg(struct r822_device *dev, int address)
+{
+ u8 reg = readb(dev->mmio + address);
+ return reg;
+}
+
+/* write register */
+static inline void r822_write_reg(struct r822_device *dev,
+ int address, u8 value)
+{
+ writeb(value, dev->mmio + address);
+}
+
+
+/* read dword sized register */
+static inline u32 r822_read_reg_dword(struct r822_device *dev, int address)
+{
+ u32 reg = le32_to_cpu(readl(dev->mmio + address));
+ return reg;
+}
+
+/* write dword sized register */
+static inline void r822_write_reg_dword(struct r822_device *dev,
+ int address, u32 value)
+{
+ writel(cpu_to_le32(value), dev->mmio + address);
+}
+
+/* returns pointer to our private structure */
+static inline struct r822_device *r822_get_dev(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = (struct nand_chip *)mtd->priv;
+ return (struct r822_device *)chip->priv;
+}
+
+
+/* check if controller supports dma */
+static void r822_dma_test(struct r822_device *dev)
+{
+ dev->dma_usable = (r822_read_reg(dev, R822_DMA_CAP) &
+ (R822_DMA1 | R822_DMA2)) == (R822_DMA1 | R822_DMA2);
+
+ if (!dev->dma_usable)
+ dbg("Non dma capable device detected, dma disabled");
+
+ if (!enable_dma) {
+ dbg("disabling dma on user request");
+ dev->dma_usable = 0;
+ }
+}
+
+/*
+ * Enable dma. Enables ether first or second stage of the DMA,
+ * Expects dev->dma_dir and dev->dma_state be set
+ */
+static void r822_dma_enable(struct r822_device *dev)
+{
+ u8 dma_reg = dev->dma_dir ? R822_DMA_READ : 0;
+
+ if (dev->dma_state == DMA_INTERNAL)
+ dma_reg |= R822_DMA_INTERNAL;
+ else {
+ dma_reg |= R822_DMA_MEMORY;
+ r822_write_reg_dword(dev, R822_DMA_ADDR,
+ cpu_to_le32(dev->phys_dma_addr));
+ }
+
+ r822_write_reg(dev, R822_DMA_IRQ_STA,
+ r822_read_reg(dev, R822_DMA_IRQ_STA));
+
+ r822_write_reg(dev, R822_DMA_SETTINGS, dma_reg);
+ r822_write_reg(dev, R822_DMA_IRQ_ENABLE,
+ R822_DMA_IRQ_INTERNAL |
+ R822_DMA_IRQ_ERROR |
+ R822_DMA_IRQ_MEMORY);
+}
+
+/*
+ * Disable dma, called from the interrupt handler, which specifies
+ * success of the operation via 'error' argument
+ */
+static void r822_dma_done(struct r822_device *dev, int error)
+{
+ WARN_ON(dev->dma_stage == 0);
+
+ if (error)
+ dbg("dma: complete with error");
+
+ r822_write_reg(dev, R822_DMA_IRQ_STA,
+ r822_read_reg(dev, R822_DMA_IRQ_STA));
+
+ r822_write_reg(dev, R822_DMA_SETTINGS, 0);
+ r822_write_reg(dev, R822_DMA_IRQ_ENABLE, 0);
+
+ dev->dma_error = error;
+ dev->dma_stage = 0;
+
+ if (dev->phys_dma_addr && dev->phys_dma_addr != dev->phys_bounce_buffer)
+ pci_unmap_single(dev->pci_dev, dev->phys_dma_addr, R822_DMA_LEN,
+ dev->dma_dir ? PCI_DMA_FROMDEVICE : PCI_DMA_TODEVICE);
+ complete(&dev->dma_done);
+}
+
+/*
+ * Wait, till dma is done, which includes both phases of it
+ */
+static int r822_dma_wait(struct r822_device *dev)
+{
+ long timeout = wait_for_completion_timeout(&dev->dma_done,
+ msecs_to_jiffies(1000));
+ if (!timeout)
+ return -ETIMEDOUT;
+ return 0;
+}
+
+/*
+ * Read/Write one page using dma. Only pages can be read (512 bytes)
+*/
+static void r822_do_dma(struct r822_device *dev, uint8_t *buf, int do_read)
+{
+ int bounce = 0;
+ unsigned long flags;
+ int error;
+
+ dev->dma_error = 0;
+
+ /* Set dma direction */
+ dev->dma_dir = do_read;
+ dev->dma_stage = 1;
+
+ /* Set intial dma state: for reading first fill on board buffer,
+ from device, for writes first fill the buffer from memory*/
+ dev->dma_state = do_read ? DMA_INTERNAL : DMA_MEMORY;
+
+ /* if incoming buffer is not page aligned, we should do bounce */
+ if ((unsigned long)buf & (R822_DMA_LEN-1))
+ bounce = 1;
+
+ if (!bounce) {
+ dev->phys_dma_addr = pci_map_single(dev->pci_dev, (void *)buf,
+ R822_DMA_LEN,
+ (do_read ? PCI_DMA_FROMDEVICE : PCI_DMA_TODEVICE));
+
+ if (dev->phys_dma_addr == DMA_ERROR_CODE)
+ bounce = 1;
+ }
+
+ if (bounce) {
+ dev->phys_dma_addr = dev->phys_bounce_buffer;
+ if (!do_read)
+ memcpy(dev->bounce_buffer, buf, R822_DMA_LEN);
+ }
+
+ /* Enable DMA */
+ spin_lock_irqsave(&dev->irqlock, flags);
+ r822_dma_enable(dev);
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+
+ /* Wait till complete */
+ error = r822_dma_wait(dev);
+
+ if (error) {
+ r822_dma_done(dev, error);
+ return;
+ }
+
+ if (do_read && bounce)
+ memcpy((void *)buf, dev->bounce_buffer, R822_DMA_LEN);
+}
+
+/*
+ * Program data lines of the nand chip to send data to it
+ */
+void r822_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+ struct r822_device *dev = r822_get_dev(mtd);
+ u32 reg;
+
+ /* Don't allow any access to hardware if we suspect card removal */
+ if (dev->card_unstable)
+ return;
+
+ /* Special case for whole sector read */
+ if (len == R822_DMA_LEN && dev->dma_usable) {
+ r822_do_dma(dev, (uint8_t *)buf, 0);
+ return;
+ }
+
+ /* write DWORD chinks - faster */
+ while (len) {
+ reg = buf[0] | buf[1] << 8 | buf[2] << 16 | buf[3] << 24;
+ r822_write_reg_dword(dev, R822_DATALINE, reg);
+ buf += 4;
+ len -= 4;
+
+ }
+
+ /* write rest */
+ while (len)
+ r822_write_reg(dev, R822_DATALINE, *buf++);
+}
+
+/*
+ * Read data lines of the nand chip to retrieve data
+ */
+void r822_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct r822_device *dev = r822_get_dev(mtd);
+ u32 reg;
+
+ if (dev->card_unstable) {
+ /* since we can't signal error here, at least, return
+ predictable buffer */
+ memset(buf, 0, len);
+ return;
+ }
+
+ /* special case for whole sector read */
+ if (len == R822_DMA_LEN && dev->dma_usable) {
+ r822_do_dma(dev, buf, 1);
+ return;
+ }
+
+ /* read in dword sized chunks */
+ while (len >= 4) {
+
+ reg = r822_read_reg_dword(dev, R822_DATALINE);
+ *buf++ = reg & 0xFF;
+ *buf++ = (reg >> 8) & 0xFF;
+ *buf++ = (reg >> 16) & 0xFF;
+ *buf++ = (reg >> 24) & 0xFF;
+ len -= 4;
+ }
+
+ /* read the reset by bytes */
+ while (len--)
+ *buf++ = r822_read_reg(dev, R822_DATALINE);
+}
+
+/*
+ * Read one byte from nand chip
+ */
+static uint8_t r822_read_byte(struct mtd_info *mtd)
+{
+ struct r822_device *dev = r822_get_dev(mtd);
+
+ /* Same problem as in r822_read_buf.... */
+ if (dev->card_unstable)
+ return 0;
+
+ return r822_read_reg(dev, R822_DATALINE);
+}
+
+
+/*
+ * Readback the buffer to verify it
+ */
+int r822_verify_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+ struct r822_device *dev = r822_get_dev(mtd);
+
+ /* We can't be sure about anything here... */
+ if (dev->card_unstable)
+ return -1;
+
+ /* This will never happen, unless you wired up a nand chip
+ with > 512 bytes page to the reader */
+ if (len > SM_SECTOR_SIZE)
+ return 0;
+
+ r822_read_buf(mtd, dev->tmp_buffer, len);
+ return memcmp(buf, dev->tmp_buffer, len);
+}
+
+/*
+ * Control several chip lines & send commands
+ */
+void r822_cmdctl(struct mtd_info *mtd, int dat, unsigned int ctrl)
+{
+ struct r822_device *dev = r822_get_dev(mtd);
+
+ if (dev->card_unstable)
+ return;
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+
+ dev->ctlreg &= ~(R822_CTL_DATA | R822_CTL_COMMAND |
+ R822_CTL_ON | R822_CTL_CARDENABLE);
+
+ if (ctrl & NAND_ALE)
+ dev->ctlreg |= R822_CTL_DATA;
+
+ if (ctrl & NAND_CLE)
+ dev->ctlreg |= R822_CTL_COMMAND;
+
+ if (ctrl & NAND_NCE)
+ dev->ctlreg |= (R822_CTL_CARDENABLE | R822_CTL_ON);
+ else
+ dev->ctlreg &= ~R822_CTL_WRITE;
+
+ /* when write is stareted, enable write access */
+ if (dat == NAND_CMD_ERASE1)
+ dev->ctlreg |= R822_CTL_WRITE;
+
+ r822_write_reg(dev, R822_CTL, dev->ctlreg);
+ }
+
+
+ /* HACK: NAND_CMD_SEQIN is called without NAND_CTRL_CHANGE, but we need
+ to set write mode */
+ if (dat == NAND_CMD_SEQIN && (dev->ctlreg & R822_CTL_COMMAND)) {
+ dev->ctlreg |= R822_CTL_WRITE;
+ r822_write_reg(dev, R822_CTL, dev->ctlreg);
+ }
+
+ if (dat != NAND_CMD_NONE)
+ r822_write_reg(dev, R822_DATALINE, dat);
+}
+
+/*
+ * Wait till card is ready.
+ * based on nand_wait, but returns errors if DMA error happened
+ */
+int r822_wait(struct mtd_info *mtd, struct nand_chip *chip)
+{
+ struct r822_device *dev = (struct r822_device *)chip->priv;
+
+ unsigned long timeout;
+ int status;
+
+ timeout = jiffies + (chip->state == FL_ERASING ?
+ msecs_to_jiffies(400) : msecs_to_jiffies(20));
+
+ while (time_before(jiffies, timeout))
+ if (chip->dev_ready(mtd))
+ break;
+
+ chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
+ status = (int)chip->read_byte(mtd);
+
+ /* Unfortunelly, no way to send detailed error status... */
+ if (dev->dma_error) {
+ status |= NAND_STATUS_FAIL;
+ dev->dma_error = 0;
+ }
+ return status;
+}
+
+/*
+ * Check if card is ready
+ */
+
+int r822_ready(struct mtd_info *mtd)
+{
+ struct r822_device *dev = r822_get_dev(mtd);
+ return !(r822_read_reg(dev, R822_CARD_STA) & R822_CARD_STA_BUSY);
+}
+
+
+/*
+ * Set ECC engine mode
+*/
+
+void r822_ecc_hwctl(struct mtd_info *mtd, int mode)
+{
+ struct r822_device *dev = r822_get_dev(mtd);
+
+ if (dev->card_unstable)
+ return;
+
+ switch (mode) {
+ case NAND_ECC_READ:
+ case NAND_ECC_WRITE:
+ /* enable ecc generation/check*/
+ dev->ctlreg |= R822_CTL_ECC_ENABLE;
+
+ /* flush ecc buffer */
+ r822_write_reg(dev, R822_CTL,
+ dev->ctlreg | R822_CTL_ECC_ACCESS);
+
+ r822_read_reg(dev, R822_DATALINE);
+ r822_write_reg(dev, R822_CTL, dev->ctlreg);
+ return;
+
+ case NAND_ECC_READSYN:
+ /* disable ecc generation */
+ dev->ctlreg &= ~R822_CTL_ECC_ENABLE;
+ r822_write_reg(dev, R822_CTL, dev->ctlreg);
+ }
+}
+
+/*
+ * Calculate ECC, only used for writes
+ */
+
+int r822_ecc_calculate(struct mtd_info *mtd, const uint8_t *dat,
+ uint8_t *ecc_code)
+{
+ struct r822_device *dev = r822_get_dev(mtd);
+ struct sm_oob *oob = (struct sm_oob *)ecc_code;
+ u32 ecc1, ecc2;
+
+ if (dev->card_unstable)
+ return 0;
+
+ dev->ctlreg &= ~R822_CTL_ECC_ENABLE;
+ r822_write_reg(dev, R822_CTL, dev->ctlreg | R822_CTL_ECC_ACCESS);
+
+ ecc1 = r822_read_reg_dword(dev, R822_DATALINE);
+ ecc2 = r822_read_reg_dword(dev, R822_DATALINE);
+
+ oob->ecc1[0] = (ecc1) & 0xFF;
+ oob->ecc1[1] = (ecc1 >> 8) & 0xFF;
+ oob->ecc1[2] = (ecc1 >> 16) & 0xFF;
+
+ oob->ecc2[0] = (ecc2) & 0xFF;
+ oob->ecc2[1] = (ecc2 >> 8) & 0xFF;
+ oob->ecc2[2] = (ecc2 >> 16) & 0xFF;
+
+ r822_write_reg(dev, R822_CTL, dev->ctlreg);
+ return 0;
+}
+
+/*
+ * Correct the data using ECC, hw did almost everything for us
+ */
+
+int r822_ecc_correct(struct mtd_info *mtd, uint8_t *dat,
+ uint8_t *read_ecc, uint8_t *calc_ecc)
+{
+ u16 ecc_reg;
+ u8 ecc_status, err_byte;
+ int i, error = 0;
+
+ struct r822_device *dev = r822_get_dev(mtd);
+
+ if (dev->card_unstable)
+ return 0;
+
+ r822_write_reg(dev, R822_CTL, dev->ctlreg | R822_CTL_ECC_ACCESS);
+ ecc_reg = r822_read_reg_dword(dev, R822_DATALINE);
+ r822_write_reg(dev, R822_CTL, dev->ctlreg);
+
+ for (i = 0 ; i <= 1 ; i++) {
+
+ ecc_status = (ecc_reg >> 8) & 0xFF;
+
+ /* ecc uncorrectable error */
+ if (ecc_status & R822_ECC_FAIL) {
+ dbg("ecc: unrecoverable error, in half %d", i);
+ error = -1;
+ goto exit;
+ }
+
+ /* correctable error */
+ if (ecc_status & R822_ECC_CORRECTABLE) {
+
+ err_byte = ecc_reg & 0xFF;
+ dbg("ecc: recoverable error, "
+ "in half %d, byte %d, bit %d", i,
+ err_byte, ecc_status & R822_ECC_ERR_BIT_MSK);
+
+ dat[err_byte] ^=
+ 1 << (ecc_status & R822_ECC_ERR_BIT_MSK);
+ error++;
+ }
+
+ dat += 256;
+ ecc_reg >>= 16;
+ }
+exit:
+ return error;
+}
+
+/*
+ * This is copy of nand_read_oob_std
+ * nand_read_oob_syndrome assumes we can send column address - we can't
+ */
+static int r822_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page, int sndcmd)
+{
+ if (sndcmd) {
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
+ sndcmd = 0;
+ }
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+ return sndcmd;
+}
+
+/*
+ * Start the hardware
+ */
+
+void r822_device_start(struct r822_device *dev)
+{
+ if (r822_read_reg(dev, R822_HW) & R822_HW_UNKNOWN) {
+ r822_write_reg(dev, R822_CTL, R822_CTL_RESET | R822_CTL_ON);
+ r822_write_reg_dword(dev, R822_HW, R822_HW_ENABLED);
+ } else {
+ r822_write_reg(dev, R822_HW, R822_HW_ENABLED);
+ r822_write_reg(dev, R822_CTL, R822_CTL_RESET | R822_CTL_ON);
+ r822_write_reg(dev, R822_CTL, 0);
+ }
+ msleep(200);
+}
+
+
+/*
+ * Shutdown the hardware
+ */
+
+void r822_device_shutdown(struct r822_device *dev)
+{
+ r822_write_reg(dev, R822_HW, 0);
+ r822_write_reg(dev, R822_CTL, R822_CTL_RESET);
+}
+
+/*
+ * Test if card is present
+ */
+
+void r822_card_update_present(struct r822_device *dev)
+{
+ unsigned long flags;
+ u8 reg;
+
+ spin_lock_irqsave(&dev->irqlock, flags);
+ reg = r822_read_reg(dev, R822_CARD_STA);
+ dev->card_detected = !!(reg & R822_CARD_STA_PRESENT);
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+}
+
+/*
+ * Update card detection IRQ state according to current card state
+ * which is read in r822_card_update_present
+ */
+void r822_update_card_detect(struct r822_device *dev)
+{
+ int card_detect_reg = R822_CARD_IRQ_GENABLE;
+ card_detect_reg |= dev->card_detected ?
+ R822_CARD_IRQ_REMOVE : R822_CARD_IRQ_INSERT;
+
+ r822_write_reg(dev, R822_CARD_IRQ_ENABLE, card_detect_reg);
+}
+
+ssize_t r822_media_type_show(struct device *sys_dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct mtd_info *mtd = container_of(sys_dev, struct mtd_info, dev);
+ struct r822_device *dev = r822_get_dev(mtd);
+ char *data = dev->sm ? "smartmedia" : "xd";
+
+ strcpy(buf, data);
+ return strlen(data);
+}
+
+DEVICE_ATTR(media_type, S_IRUGO, r822_media_type_show, NULL);
+
+
+/* Detect properties of card in slot */
+void r822_update_media_status(struct r822_device *dev)
+{
+ u8 reg;
+ unsigned long flags;
+ int readonly;
+
+ spin_lock_irqsave(&dev->irqlock, flags);
+ if (!dev->card_detected) {
+ dbg("card removed");
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+ return ;
+ }
+
+ readonly = r822_read_reg(dev, R822_CARD_STA) & R822_CARD_STA_RO;
+ reg = r822_read_reg(dev, R822_DMA_CAP);
+ dev->sm = (reg & (R822_DMA1 | R822_DMA2)) && (reg & R822_SMBIT);
+
+ dbg("detected %s %s card in slot",
+ dev->sm ? "SmartMedia" : "xD",
+ readonly ? "readonly" : "writeable");
+
+ dev->readonly = readonly;
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+}
+
+/*
+ * Register the nand device
+ * Called when the card is detected
+ */
+int r822_register_nand_device(struct r822_device *dev)
+{
+ dev->mtd = kzalloc(sizeof(struct mtd_info), GFP_KERNEL);
+
+ if (!dev->mtd)
+ goto error1;
+
+ WARN_ON(dev->card_registred);
+
+ dev->mtd->owner = THIS_MODULE;
+ dev->mtd->priv = dev->chip;
+
+ if (dev->readonly)
+ dev->chip->options |= NAND_ROM;
+
+ r822_device_start(dev);
+ if (sm_register_device(dev->mtd))
+ goto error2;
+
+ sysfs_create_file(&dev->mtd->dev.kobj, &dev_attr_media_type.attr);
+
+ dev->card_registred = 1;
+ return 0;
+error2:
+ kfree(dev->mtd);
+error1:
+ /* Force card redetect */
+ dev->card_detected = 0;
+ return -1;
+}
+
+/*
+ * Unregister the card
+ */
+
+void r822_unregister_nand_device(struct r822_device *dev)
+{
+ if (!dev->card_registred)
+ return;
+
+
+ nand_release(dev->mtd);
+ r822_device_shutdown(dev);
+ dev->card_registred = 0;
+
+ sysfs_remove_file(&dev->mtd->dev.kobj, &dev_attr_media_type.attr);
+ kfree(dev->mtd);
+ dev->mtd = NULL;
+}
+
+
+/* Card state updater */
+void r822_card_detect_work(struct work_struct *work)
+{
+ struct r822_device *dev =
+ container_of(work, struct r822_device, card_detect_work.work);
+
+ r822_card_update_present(dev);
+ dev->card_unstable = 0;
+
+ /* false alarm */
+ if (dev->card_detected == dev->card_registred)
+ goto exit;
+
+ /* Read media properties */
+ r822_update_media_status(dev);
+
+ /* Register the card */
+ if (dev->card_detected)
+ r822_register_nand_device(dev);
+ else
+ r822_unregister_nand_device(dev);
+exit:
+ /* Update detection logic */
+ r822_update_card_detect(dev);
+}
+
+
+/* Ack + disable IRQ generation */
+static void r822_disable_irqs(struct r822_device *dev)
+{
+ u8 reg;
+ reg = r822_read_reg(dev, R822_CARD_IRQ_ENABLE);
+ r822_write_reg(dev, R822_CARD_IRQ_ENABLE, reg & ~R822_CARD_IRQ_MASK);
+
+ reg = r822_read_reg(dev, R822_DMA_IRQ_ENABLE);
+ r822_write_reg(dev, R822_DMA_IRQ_ENABLE, reg & ~R822_DMA_IRQ_MASK);
+
+ reg = r822_read_reg(dev, R822_CARD_IRQ_STA);
+ r822_write_reg(dev, R822_CARD_IRQ_STA, reg);
+
+ reg = r822_read_reg(dev, R822_DMA_IRQ_STA);
+ r822_write_reg(dev, R822_DMA_IRQ_STA, reg);
+
+}
+
+/* Interrupt handler */
+static irqreturn_t r822_irq(int irq, void *data)
+{
+ struct r822_device *dev = (struct r822_device *)data;
+
+ u8 card_status, dma_status;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dev->irqlock, flags);
+
+ /* We can recieve shared interrupt while pci is suspended
+ in that case reads will return 0xFFFFFFFF.... */
+ if (dev->insuspend) {
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+ return IRQ_NONE;
+ }
+
+ /* Test card status interrupt status */
+ card_status =
+ r822_read_reg(dev, R822_CARD_IRQ_STA) & R822_CARD_IRQ_MASK;
+
+ if (card_status & (R822_CARD_IRQ_INSERT|R822_CARD_IRQ_REMOVE)) {
+
+ dev->card_detected = !!(card_status & R822_CARD_IRQ_INSERT);
+
+ /* we shouldn't recieve any interrupts if we wait for card
+ to settle */
+ WARN_ON(dev->card_unstable);
+
+ /* disable irqs while card is unstable */
+ /* this will timeout DMA if active, but better that garbage */
+ r822_disable_irqs(dev);
+
+ /* let, card state to settle a bit, and then do the work */
+ if (!dev->card_unstable) {
+ dev->card_unstable = 1;
+ queue_delayed_work(dev->card_workqueue,
+ &dev->card_detect_work, msecs_to_jiffies(100));
+ }
+
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+ return IRQ_HANDLED;
+ }
+
+
+ /* test and ack dma interrupts */
+ dma_status = r822_read_reg(dev, R822_DMA_IRQ_STA) & R822_DMA_IRQ_MASK;
+ r822_write_reg(dev, R822_DMA_IRQ_STA, dma_status);
+
+ if (!dma_status) {
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+ return IRQ_NONE;
+ }
+
+ if (dma_status & R822_DMA_IRQ_ERROR) {
+ dbg("recieved dma error IRQ");
+ r822_dma_done(dev, -EIO);
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+ return IRQ_HANDLED;
+ }
+
+
+ /* recieved DMA interrupt out of nowhere? */
+ WARN_ON_ONCE(dev->dma_stage == 0);
+
+ if (dev->dma_stage == 0) {
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+ return IRQ_HANDLED;
+ }
+
+ /* done device access */
+ if (dev->dma_state == DMA_INTERNAL &&
+ (dma_status & R822_DMA_IRQ_INTERNAL)) {
+
+ dev->dma_state = DMA_MEMORY;
+ dev->dma_stage++;
+ }
+
+ /* done memory DMA */
+ if (dev->dma_state == DMA_MEMORY &&
+ (dma_status & R822_DMA_IRQ_MEMORY)) {
+ dev->dma_state = DMA_INTERNAL;
+ dev->dma_stage++;
+ }
+
+ /* Enable 2nd half of dma dance */
+ if (dev->dma_stage == 2)
+ r822_dma_enable(dev);
+
+
+ /* Operation done */
+ if (dev->dma_stage == 3)
+ r822_dma_done(dev, 0);
+
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+ return IRQ_HANDLED;
+}
+
+int r822_probe(struct pci_dev *pci_dev, const struct pci_device_id *id)
+{
+ int error;
+ struct nand_chip *chip;
+ struct r822_device *dev;
+
+ /* pci initialization */
+ error = pci_enable_device(pci_dev);
+
+ if (error)
+ goto error1;
+
+ pci_set_master(pci_dev);
+
+ error = pci_set_dma_mask(pci_dev, DMA_32BIT_MASK);
+ if (error)
+ goto error2;
+
+ error = pci_request_regions(pci_dev, DRV_NAME);
+
+ if (error)
+ goto error3;
+
+ error = -ENOMEM;
+
+ /* init nand chip, but register it only on card insert */
+ chip = kzalloc(sizeof(struct nand_chip), GFP_KERNEL);
+
+ if (!chip)
+ goto error4;
+
+ /* commands */
+ chip->cmd_ctrl = r822_cmdctl;
+ chip->waitfunc = r822_wait;
+ chip->dev_ready = r822_ready;
+
+ /* I/O */
+ chip->read_byte = r822_read_byte;
+ chip->read_buf = r822_read_buf;
+ chip->write_buf = r822_write_buf;
+ chip->verify_buf = r822_verify_buf;
+
+ /* ecc */
+ chip->ecc.mode = NAND_ECC_HW_SYNDROME;
+ chip->ecc.size = R822_DMA_LEN;
+ chip->ecc.bytes = SM_OOB_SIZE;
+ chip->ecc.hwctl = r822_ecc_hwctl;
+ chip->ecc.calculate = r822_ecc_calculate;
+ chip->ecc.correct = r822_ecc_correct;
+
+ /* TODO: hack */
+ chip->ecc.read_oob = r822_read_oob;
+
+ /* init our device structure */
+ dev = kzalloc(sizeof(struct r822_device), GFP_KERNEL);
+
+ if (!dev)
+ goto error5;
+
+ chip->priv = dev;
+ dev->chip = chip;
+ dev->pci_dev = pci_dev;
+ pci_set_drvdata(pci_dev, dev);
+
+ dev->bounce_buffer = pci_alloc_consistent(pci_dev, R822_DMA_LEN,
+ &dev->phys_bounce_buffer);
+
+ if (!dev->bounce_buffer)
+ goto error6;
+
+
+ error = -ENODEV;
+ dev->mmio = pci_ioremap_bar(pci_dev, 0);
+
+ if (!dev->mmio)
+ goto error7;
+
+ error = -ENOMEM;
+ dev->tmp_buffer = kzalloc(SM_SECTOR_SIZE, GFP_KERNEL);
+
+ if (!dev->tmp_buffer)
+ goto error8;
+
+ init_completion(&dev->dma_done);
+
+ dev->card_workqueue = create_freezeable_workqueue(DRV_NAME);
+
+ if (!dev->card_workqueue)
+ goto error9;
+
+ INIT_DELAYED_WORK(&dev->card_detect_work, r822_card_detect_work);
+
+ /* shutdown everything - precation */
+ r822_device_shutdown(dev);
+ r822_disable_irqs(dev);
+
+ r822_dma_test(dev);
+
+ /*register irq handler*/
+ error = -ENODEV;
+ if (request_irq(pci_dev->irq, &r822_irq, IRQF_SHARED,
+ DRV_NAME, dev))
+ goto error10;
+
+ dev->irq = pci_dev->irq;
+ spin_lock_init(&dev->irqlock);
+
+ /* kick initial present test */
+ dev->card_detected = 0;
+ r822_card_update_present(dev);
+ queue_delayed_work(dev->card_workqueue,
+ &dev->card_detect_work, 0);
+
+ /* Load the FTL */
+ request_module_nowait("sm_ftl");
+
+ printk(KERN_NOTICE DRV_NAME ": driver loaded succesfully\n");
+ return 0;
+
+error10:
+ destroy_workqueue(dev->card_workqueue);
+error9:
+ kfree(dev->tmp_buffer);
+error8:
+ pci_iounmap(pci_dev, dev->mmio);
+error7:
+ pci_free_consistent(pci_dev, R822_DMA_LEN,
+ dev->bounce_buffer, dev->phys_bounce_buffer);
+error6:
+ kfree(dev);
+error5:
+ kfree(chip);
+error4:
+ pci_release_regions(pci_dev);
+error3:
+error2:
+ pci_disable_device(pci_dev);
+error1:
+ return error;
+}
+
+
+void r822_remove(struct pci_dev *pci_dev)
+{
+ struct r822_device *dev = pci_get_drvdata(pci_dev);
+
+ /* Stop detect workqueue -
+ we are going to unregister the device anyway*/
+ cancel_delayed_work_sync(&dev->card_detect_work);
+ destroy_workqueue(dev->card_workqueue);
+
+ /* Unregister the device, this might make more IO */
+ r822_unregister_nand_device(dev);
+
+ /* Stop interrupts */
+ r822_disable_irqs(dev);
+ synchronize_irq(dev->irq);
+ free_irq(dev->irq, dev);
+
+ /* Cleanup */
+ kfree(dev->tmp_buffer);
+ pci_iounmap(pci_dev, dev->mmio);
+ pci_free_consistent(pci_dev, R822_DMA_LEN,
+ dev->bounce_buffer, dev->phys_bounce_buffer);
+ kfree(dev);
+ kfree(dev->chip);
+
+ /* Shutdown the PCI device */
+ pci_release_regions(pci_dev);
+ pci_disable_device(pci_dev);
+}
+
+void r822_shutdown(struct pci_dev *pci_dev)
+{
+ struct r822_device *dev = pci_get_drvdata(pci_dev);
+
+ cancel_delayed_work_sync(&dev->card_detect_work);
+ r822_disable_irqs(dev);
+ synchronize_irq(dev->irq);
+ pci_disable_device(pci_dev);
+}
+
+int r822_suspend(struct device *device)
+{
+ struct r822_device *dev = pci_get_drvdata(to_pci_dev(device));
+ unsigned long flags;
+
+ if (dev->ctlreg & R822_CTL_CARDENABLE)
+ return -EBUSY;
+
+ /* First make sure the detect work is gone */
+ cancel_delayed_work_sync(&dev->card_detect_work);
+
+ /* Turn off the interrupts and stop the device */
+ r822_disable_irqs(dev);
+ r822_device_shutdown(dev);
+
+ spin_lock_irqsave(&dev->irqlock, flags);
+ dev->insuspend = 1;
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+
+ /* At that point, even if interrupt handler is running, it will quit */
+ /* So wait for this to happen explictly */
+ synchronize_irq(dev->irq);
+
+ /* If card was pulled off just during the suspend, which is very
+ unlikely, we will remove it on resume, it too late now
+ anyway... */
+ dev->card_unstable = 0;
+
+ pci_save_state(to_pci_dev(device));
+ pci_set_power_state(to_pci_dev(device), PCI_D3cold);
+ return 0;
+}
+
+int r822_resume(struct device *device)
+{
+ struct r822_device *dev = pci_get_drvdata(to_pci_dev(device));
+ unsigned long flags;
+
+ /* Turn on the hardware */
+ pci_set_power_state(to_pci_dev(device), PCI_D0);
+ pci_restore_state(to_pci_dev(device));
+
+ /* Disable everything - precation */
+ r822_disable_irqs(dev);
+ r822_device_shutdown(dev);
+
+ /* Detect the card change */
+ r822_card_update_present(dev);
+
+ /* If card status changed, just do the work */
+ if (dev->card_detected != dev->card_registred) {
+ dbg("card was %s during low power state",
+ dev->card_detected ? "added" : "removed");
+
+ queue_delayed_work(dev->card_workqueue,
+ &dev->card_detect_work, 0);
+ return 0;
+ }
+
+ /* Otherwise, initialize the card */
+ if (dev->card_registred) {
+ r822_device_start(dev);
+ dev->chip->select_chip(dev->mtd, 0);
+ dev->chip->cmdfunc(dev->mtd, NAND_CMD_RESET, -1, -1);
+ dev->chip->select_chip(dev->mtd, -1);
+ }
+
+ /* Now its safe for IRQ to run */
+ spin_lock_irqsave(&dev->irqlock, flags);
+ dev->insuspend = 0;
+ spin_unlock_irqrestore(&dev->irqlock, flags);
+
+ /* Program card detection IRQ */
+ r822_update_card_detect(dev);
+ return 0;
+}
+
+static const struct pci_device_id r822_pci_id_tbl[] = {
+
+ { PCI_VDEVICE(RICOH, PCI_DEVICE_ID_RICOH_R5C852), },
+ { },
+};
+
+MODULE_DEVICE_TABLE(pci, r822_pci_id_tbl);
+
+SIMPLE_DEV_PM_OPS(r822_pm_ops, r822_suspend, r822_resume);
+
+
+static struct pci_driver r822_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = r822_pci_id_tbl,
+ .probe = r822_probe,
+ .remove = r822_remove,
+ .shutdown = r822_shutdown,
+ .driver.pm = &r822_pm_ops,
+};
+
+static __init int r822_module_init(void)
+{
+ return pci_register_driver(&r822_pci_driver);
+}
+
+static void __exit r822_module_exit(void)
+{
+ pci_unregister_driver(&r822_pci_driver);
+}
+
+module_init(r822_module_init);
+module_exit(r822_module_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Maxim Levitsky <[email protected]>");
+MODULE_DESCRIPTION("Ricoh 85xx xD/smartmedia card reader driver");
diff --git a/drivers/mtd/nand/r822.h b/drivers/mtd/nand/r822.h
new file mode 100644
index 0000000..d56602c
--- /dev/null
+++ b/drivers/mtd/nand/r822.h
@@ -0,0 +1,153 @@
+/*
+ * Copyright (C) 2009 - Maxim Levitsky
+ * driver for Ricoh xD readers
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/pci.h>
+#include <linux/completion.h>
+#include <linux/workqueue.h>
+#include <linux/mtd/nand.h>
+#include <linux/spinlock.h>
+
+
+/* nand interface + ecc
+ byte write/read does one cycle on nand data lines.
+ dword write/read does 4 cycles
+ if R822_CTL_ECC_ACCESS is set in R822_CTL, then dword read reads
+ results of ecc correction, if DMA read was done before.
+ If write was done two dword reads read generated ecc checksums
+*/
+#define R822_DATALINE 0x00
+
+/* control register */
+#define R822_CTL 0x04
+#define R822_CTL_COMMAND 0x01 /* send command (#CLE)*/
+#define R822_CTL_DATA 0x02 /* read/write data (#ALE)*/
+#define R822_CTL_ON 0x04 /* only seem to controls the hd led, */
+ /* but has to be set on start...*/
+#define R822_CTL_RESET 0x08 /* unknown, set only on start once*/
+#define R822_CTL_CARDENABLE 0x10 /* probably (#CE) - always set*/
+#define R822_CTL_ECC_ENABLE 0x20 /* enable ecc engine */
+#define R822_CTL_ECC_ACCESS 0x40 /* read/write ecc via reg #0*/
+#define R822_CTL_WRITE 0x80 /* set when performing writes (#WP) */
+
+
+/* card detection status */
+#define R822_CARD_STA 0x05
+#define R822_CARD_STA_UNUSED1 0x01 /* unknown */
+#define R822_CARD_STA_RO 0x02 /* card is readonly -- test on #WP???*/
+#define R822_CARD_STA_PRESENT 0x04 /* card is present (#CD) */
+#define R822_CARD_STA_BUSY 0x80 /* card is busy - (#R/B) */
+
+/* card detection irq status*/
+#define R822_CARD_IRQ_STA 0x06 /* IRQ status */
+
+/* card detection irq enable */
+#define R822_CARD_IRQ_ENABLE 0x07 /* IRQ enable */
+
+#define R822_CARD_IRQ_UNUSED1 0x01 /* unknown */
+#define R822_CARD_IRQ_REMOVE 0x04 /* detect card removal */
+#define R822_CARD_IRQ_INSERT 0x08 /* detect card insert */
+#define R822_CARD_IRQ_UNUSED2 0x10 /* unknown */
+#define R822_CARD_IRQ_GENABLE 0x80 /* general enable */
+#define R822_CARD_IRQ_MASK 0x1D
+
+
+/* hardware enable */
+#define R822_HW 0x08
+#define R822_HW_ENABLED 0x01 /* hw enabled */
+#define R822_HW_UNKNOWN 0x80
+
+
+/* dma capabilities */
+#define R822_DMA_CAP 0x09
+#define R822_SMBIT 0x20 /* if set with bit #6 or bit #7, then */
+ /* hw is smartmedia */
+#define R822_DMA1 0x40 /* if set w/bit #7, dma is supported */
+#define R822_DMA2 0x80 /* if set w/bit #6, dma is supported */
+
+
+/* physical DMA address - 32 bit value*/
+#define R822_DMA_ADDR 0x0C
+
+
+/* dma settings */
+#define R822_DMA_SETTINGS 0x10
+#define R822_DMA_MEMORY 0x01 /* (memory <-> internal hw buffer) */
+#define R822_DMA_READ 0x02 /* 0 = write, 1 = read */
+#define R822_DMA_INTERNAL 0x04 /* (internal hw buffer <-> card) */
+
+/* dma IRQ status */
+#define R822_DMA_IRQ_STA 0x14
+
+/* dma IRQ enable */
+#define R822_DMA_IRQ_ENABLE 0x18
+
+#define R822_DMA_IRQ_MEMORY 0x01 /* (memory <-> internal hw buffer) */
+#define R822_DMA_IRQ_ERROR 0x02 /* error did happen */
+#define R822_DMA_IRQ_INTERNAL 0x04 /* (internal hw buffer <-> card) */
+#define R822_DMA_IRQ_MASK 0x07 /* mask of all IRQ bits */
+
+
+/* ECC syndrome format - read from reg #0 will return two copies of these for
+ each half of the page.
+ first byte is error byte location, and second, bit location + flags */
+#define R822_ECC_ERR_BIT_MSK 0x07 /* error bit location */
+#define R822_ECC_CORRECT 0x10 /* no errors - (guessed) */
+#define R822_ECC_CORRECTABLE 0x20 /* correctable error exist */
+#define R822_ECC_FAIL 0x40 /* non correctable error detected */
+
+#define R822_DMA_LEN 512
+
+#define DMA_INTERNAL 0
+#define DMA_MEMORY 1
+
+struct r822_device {
+ void __iomem *mmio; /* mmio */
+ struct mtd_info *mtd; /* mtd backpointer */
+ struct nand_chip *chip; /* nand chip backpointer */
+ struct pci_dev *pci_dev; /* pci backpointer */
+
+ /* dma area */
+ dma_addr_t phys_dma_addr; /* bus address of buffer*/
+ struct completion dma_done; /* data transfer done */
+
+ dma_addr_t phys_bounce_buffer; /* bus address of bounce buffer */
+ u8 *bounce_buffer; /* virtual address of bounce buffer */
+
+ int dma_dir; /* 1 = read, 0 = write */
+ int dma_stage; /* 0 - idle, 1 - first step,
+ 2 - second step */
+
+ int dma_state; /* 0 = internal, 1 = memory */
+ int dma_error; /* dma errors */
+ int dma_usable; /* is it possible to use dma */
+
+ /* card status area */
+ struct delayed_work card_detect_work;
+ struct workqueue_struct *card_workqueue;
+ int card_registred; /* card registered with mtd */
+ int card_detected; /* card detected in slot */
+ int card_unstable; /* whenever the card is inserted,
+ is not known yet */
+ int readonly; /* card is readonly */
+ int sm; /* Is card smartmedia */
+
+ /* interrupt handling */
+ spinlock_t irqlock; /* IRQ protecting lock */
+ int irq; /* irq num */
+ int insuspend; /* device is suspended */
+
+ /* misc */
+ void *tmp_buffer; /* temporary buffer */
+ u8 ctlreg; /* cached contents of control reg */
+};
+
+#define DRV_NAME "r822"
+
+#define dbg(format, ...) \
+ printk(KERN_ERR DRV_NAME ": " format "\n", ## __VA_ARGS__)
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index cca8a04..cef49f2 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1523,6 +1523,8 @@
#define PCI_DEVICE_ID_RICOH_R5C822 0x0822
#define PCI_DEVICE_ID_RICOH_R5C832 0x0832
#define PCI_DEVICE_ID_RICOH_R5C843 0x0843
+#define PCI_DEVICE_ID_RICOH_R5C852 0x0852
+
#define PCI_VENDOR_ID_DLINK 0x1186
#define PCI_DEVICE_ID_DLINK_DGE510T 0x4c00
--
1.6.3.3
MTD_OOB_PLACE is supposed to read/write raw oob data similiar to MTD_OOB_RAW
however due to a bug, currently its not possible to read more data that
specified in oob 'free' regions
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/nand/nand_base.c | 6 +++++-
1 files changed, 5 insertions(+), 1 deletions(-)
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 8f2958f..405c538 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -1232,6 +1232,9 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
int ret = 0;
uint32_t readlen = ops->len;
uint32_t oobreadlen = ops->ooblen;
+ uint32_t max_oobsize = ops->mode == MTD_OOB_AUTO ?
+ mtd->oobavail : mtd->oobsize;
+
uint8_t *bufpoi, *oob, *buf;
stats = mtd->ecc_stats;
@@ -1282,10 +1285,11 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
buf += bytes;
if (unlikely(oob)) {
+
/* Raw mode does data:oob:data:oob */
if (ops->mode != MTD_OOB_RAW) {
int toread = min(oobreadlen,
- chip->ecc.layout->oobavail);
+ max_oobsize);
if (toread) {
oob = nand_transfer_oob(chip,
oob, ops, toread);
--
1.6.3.3
Now that mtd block common layer is prepared for proper hotplug support, enable it here
Now all users of the mtd device have a chance to put the mtd device
when they are notified to do so, and they have to do so to make hotplug work.
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/mtdcore.c | 21 +++++++++++----------
1 files changed, 11 insertions(+), 10 deletions(-)
diff --git a/drivers/mtd/mtdcore.c b/drivers/mtd/mtdcore.c
index 3bdb7e8..0e86208 100644
--- a/drivers/mtd/mtdcore.c
+++ b/drivers/mtd/mtdcore.c
@@ -341,31 +341,32 @@ int add_mtd_device(struct mtd_info *mtd)
int del_mtd_device (struct mtd_info *mtd)
{
int ret;
+ struct mtd_notifier *not;
mutex_lock(&mtd_table_mutex);
if (mtd_table[mtd->index] != mtd) {
ret = -ENODEV;
- } else if (mtd->usecount) {
+ goto out_error;
+ }
+
+ /* No need to get a refcount on the module containing
+ the notifier, since we hold the mtd_table_mutex */
+ list_for_each_entry(not, &mtd_notifiers, list)
+ not->remove(mtd);
+
+ if (mtd->usecount) {
printk(KERN_NOTICE "Removing MTD device #%d (%s) with use count %d\n",
mtd->index, mtd->name, mtd->usecount);
ret = -EBUSY;
} else {
- struct mtd_notifier *not;
-
device_unregister(&mtd->dev);
-
- /* No need to get a refcount on the module containing
- the notifier, since we hold the mtd_table_mutex */
- list_for_each_entry(not, &mtd_notifiers, list)
- not->remove(mtd);
-
mtd_table[mtd->index] = NULL;
-
module_put(THIS_MODULE);
ret = 0;
}
+out_error:
mutex_unlock(&mtd_table_mutex);
return ret;
}
--
1.6.3.3
This implements new readwrite SmartMedia/xd FTL.
mtd driver must have support proper ECC and badblock vertification
based on oob parts for 512 bytes nand.
Also mtd driver must define read_oob and write_oob, which are used
to read and write both data and oob together.
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/Kconfig | 21 +
drivers/mtd/Makefile | 1 +
drivers/mtd/sm_ftl.c | 1260 ++++++++++++++++++++++++++++++++++++++++++++++++++
drivers/mtd/sm_ftl.h | 92 ++++
4 files changed, 1374 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/sm_ftl.c
create mode 100644 drivers/mtd/sm_ftl.h
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index ecf90f5..0105ae0 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -304,6 +304,27 @@ config SSFDC
This enables read only access to SmartMedia formatted NAND
flash. You can mount it with FAT file system.
+
+config SM_FTL
+ tristate "SmartMedia/xD new translation layer"
+ depends on EXPERIMENTAL && BLOCK
+ select MTD_BLKDEVS
+ help
+ This enables new and very EXPERMENTAL support for SmartMedia/xD
+ FTL (Flash tanslation layer)
+ Write support isn't yet well tested, therefore this code IS likely to
+ eat your card, so please don't use it together with valuable data.
+ Use readonly driver (CONFIG_SSFDC) instead.
+
+config SM_FTL_MUSEUM
+ boolean "Additional Support for 1MB and 2MB SmartMedia cards"
+ depends on SM_FTL && MTD_NAND
+ select MTD_NAND_ECC_SMC
+ help
+ Very old SmartMedia cards need ECC to be caluculated in the FTL
+ Such cards are very rare, thus enabling this option is mostly useless
+ Also this support is completely UNTESTED.
+
config MTD_OOPS
tristate "Log panic/oops to an MTD buffer"
depends on MTD
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 82d1e4d..d53357b 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_NFTL) += nftl.o
obj-$(CONFIG_INFTL) += inftl.o
obj-$(CONFIG_RFD_FTL) += rfd_ftl.o
obj-$(CONFIG_SSFDC) += ssfdc.o
+obj-$(CONFIG_SM_FTL) += sm_ftl.o
obj-$(CONFIG_MTD_OOPS) += mtdoops.o
nftl-objs := nftlcore.o nftlmount.o
diff --git a/drivers/mtd/sm_ftl.c b/drivers/mtd/sm_ftl.c
new file mode 100644
index 0000000..107c1de
--- /dev/null
+++ b/drivers/mtd/sm_ftl.c
@@ -0,0 +1,1260 @@
+/*
+ * Copyright (C) 2009 - Maxim Levitsky
+ * SmartMedia/xD translation layer
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/random.h>
+#include <linux/hdreg.h>
+#include <linux/kthread.h>
+#include <linux/freezer.h>
+#include <linux/sysfs.h>
+#include <linux/bitops.h>
+#include "nand/sm_common.h"
+#include "sm_ftl.h"
+
+#ifdef CONFIG_SM_FTL_MUSEUM
+#include <linux/mtd/nand_ecc.h>
+#endif
+
+
+struct workqueue_struct *cache_flush_workqueue;
+
+static int cache_timeout = 1000;
+module_param(cache_timeout, bool, S_IRUGO);
+MODULE_PARM_DESC(cache_timeout, "Timeout in ms for cache flush (1000 default");
+
+/* ------------------- sysfs attributtes ---------------------------------- */
+struct sm_sysfs_attribute {
+ struct device_attribute dev_attr;
+ char *data;
+ int len;
+};
+
+ssize_t sm_attr_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct sm_sysfs_attribute *sm_attr =
+ container_of(attr, struct sm_sysfs_attribute, dev_attr);
+
+ strncpy(buf, sm_attr->data, sm_attr->len);
+ return sm_attr->len;
+}
+
+
+#define NUM_ATTRIBUTES 1
+#define SM_CIS_VENDOR_OFFSET 0x59
+struct attribute_group *sm_create_sysfs_attributes(struct sm_ftl *ftl)
+{
+ struct attribute_group *attr_group;
+ struct attribute **attributes;
+ struct sm_sysfs_attribute *vendor_attribute;
+
+ int vendor_len = strnlen(ftl->cis_buffer + SM_CIS_VENDOR_OFFSET,
+ SM_SMALL_PAGE - SM_CIS_VENDOR_OFFSET);
+
+ char *vendor = kmalloc(vendor_len, GFP_KERNEL);
+ memcpy(vendor, ftl->cis_buffer + SM_CIS_VENDOR_OFFSET, vendor_len);
+ vendor[vendor_len] = 0;
+
+ /* Initialize sysfs attributes */
+ vendor_attribute =
+ kzalloc(sizeof(struct sm_sysfs_attribute), GFP_KERNEL);
+
+ vendor_attribute->data = vendor;
+ vendor_attribute->len = vendor_len;
+ vendor_attribute->dev_attr.attr.name = "vendor";
+ vendor_attribute->dev_attr.attr.mode = S_IRUGO;
+ vendor_attribute->dev_attr.show = sm_attr_show;
+
+
+ /* Create array of pointers to the attributes */
+ attributes = kzalloc(sizeof(struct attribute *) * (NUM_ATTRIBUTES + 1),
+ GFP_KERNEL);
+ attributes[0] = &vendor_attribute->dev_attr.attr;
+
+ /* Finally create the attribute group */
+ attr_group = kzalloc(sizeof(struct attribute_group), GFP_KERNEL);
+ attr_group->attrs = attributes;
+ return attr_group;
+}
+
+void sm_delete_sysfs_attributes(struct sm_ftl *ftl)
+{
+ struct attribute **attributes = ftl->trans->disk_attributes->attrs;
+ int i;
+
+ for (i = 0; attributes[i] ; i++) {
+
+ struct device_attribute *dev_attr = container_of(attributes[i],
+ struct device_attribute, attr);
+
+ struct sm_sysfs_attribute *sm_attr =
+ container_of(dev_attr,
+ struct sm_sysfs_attribute, dev_attr);
+
+ kfree(sm_atrr->data);
+ kfree(sm_attr);
+ }
+
+ kfree(ftl->trans->disk_attributes->attrs);
+ kfree(ftl->trans->disk_attributes);
+}
+
+
+/* ----------------------- oob helpers -------------------------------------- */
+
+static int sm_get_lba(u8 *lba)
+{
+ /* check fixed bits */
+ if ((lba[0] & 0xF8) != 0x10)
+ return -2;
+
+ /* check parity - endianess doesn't matter */
+ if (hweight16(*(u16 *)lba) & 1)
+ return -2;
+
+ return (lba[1] >> 1) | ((lba[0] & 0x07) << 7);
+}
+
+
+/*
+ * Read LBA asscociated with block
+ * returns -1, if block is erased
+ * returns -2 if error happens
+ */
+static int sm_read_lba(struct sm_oob *oob)
+{
+ static const u32 erased_pattern[4] = {
+ 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF };
+
+ u16 lba_test;
+ int lba;
+
+ /* First test for erased block */
+ if (!memcmp(oob, erased_pattern, SM_OOB_SIZE))
+ return -1;
+
+ /* Now check is both copies of the LBA differ too much */
+ lba_test = *(u16 *)oob->lba_copy1 ^ *(u16*)oob->lba_copy2;
+ if (lba_test && !is_power_of_2(lba_test))
+ return -2;
+
+ /* And read it */
+ lba = sm_get_lba(oob->lba_copy1);
+
+ if (lba == -2)
+ lba = sm_get_lba(oob->lba_copy2);
+
+ return lba;
+}
+
+static void sm_write_lba(struct sm_oob *oob, u16 lba)
+{
+ u8 tmp[2];
+
+ WARN_ON(lba >= 1000);
+
+ tmp[0] = 0x10 | ((lba >> 7) & 0x07);
+ tmp[1] = (lba << 1) & 0xFF;
+
+ if (hweight16(*(u16 *)tmp) & 0x01)
+ tmp[1] |= 1;
+
+ oob->lba_copy1[0] = oob->lba_copy2[0] = tmp[0];
+ oob->lba_copy1[1] = oob->lba_copy2[1] = tmp[1];
+}
+
+
+/* Make offset from parts */
+static loff_t sm_mkoffset(struct sm_ftl *ftl, int zone, int block, int boffset)
+{
+ WARN_ON(boffset & (SM_SECTOR_SIZE - 1));
+ WARN_ON(zone < 0 || zone >= ftl->zone_count);
+ WARN_ON(block >= ftl->zone_size);
+ WARN_ON(boffset >= ftl->block_size);
+
+ if (block == -1)
+ return -1;
+
+ return (zone * SM_MAX_ZONE_SIZE + block) * ftl->block_size + boffset;
+}
+
+/* Breaks offset into parts */
+static void sm_break_offset(struct sm_ftl *ftl, loff_t offset,
+ int *zone, int *block, int *boffset)
+{
+ *boffset = offset % ftl->block_size;
+ offset /= ftl->block_size;
+ *block = offset % ftl->max_lba;
+ offset /= ftl->max_lba;
+ *zone = offset >= ftl->zone_count ? -1 : offset;
+}
+
+/* ---------------------- low level IO ------------------------------------- */
+
+static int sm_correct_sector(u8 *buffer, struct sm_oob *oob)
+{
+#ifdef CONFIG_SM_FTL_MUSEUM
+ u8 ecc[3];
+
+ __nand_calculate_ecc(buffer, SM_SMALL_PAGE, ecc);
+ if (__nand_correct_data(buffer, ecc, oob->ecc1, SM_SMALL_PAGE) < 0)
+ return -EIO;
+
+ buffer += SM_SMALL_PAGE;
+
+ __nand_calculate_ecc(buffer, SM_SMALL_PAGE, ecc);
+ if (__nand_correct_data(buffer, ecc, oob->ecc2, SM_SMALL_PAGE) < 0)
+ return -EIO;
+#endif
+ return 0;
+}
+
+/* Reads a sector + oob*/
+static int sm_read_sector(struct sm_ftl *ftl,
+ int zone, int block, int boffset,
+ u8 *buffer, struct sm_oob *oob)
+{
+ struct mtd_info *mtd = ftl->trans->mtd;
+ struct mtd_oob_ops ops;
+ struct sm_oob tmp_oob;
+ int ret;
+ int try = 0;
+
+ /* FTL can contain -1 entries that are by default filled with bits */
+ if (block == -1) {
+ memset(buffer, 0xFF, SM_SECTOR_SIZE);
+ return 0;
+ }
+
+ /* User might not need the oob, but we do for data vertification */
+ if (!oob)
+ oob = &tmp_oob;
+
+ ops.mode = ftl->smallpagenand ? MTD_OOB_RAW : MTD_OOB_PLACE;
+ ops.ooboffs = 0;
+ ops.ooblen = SM_OOB_SIZE;
+ ops.oobbuf = (void *)oob;
+ ops.len = SM_SECTOR_SIZE;
+ ops.datbuf = buffer;
+
+again:
+ /* Retrial mode */
+ if (try++) {
+ /* Avoid infinite recursion on CIS reads, sm_recheck_media
+ won't help anyway */
+ if (zone == 0 && block == ftl->cis_block && boffset ==
+ ftl->cis_boffset)
+ return ret;
+
+ /* Test if media is stable */
+ if (try == 3 || sm_recheck_media(ftl))
+ return ret;
+ }
+
+
+ /* Unfortunelly, oob read will _always_ succeed,
+ despite card removal..... */
+ ret = mtd->read_oob(mtd, sm_mkoffset(ftl, zone, block, boffset), &ops);
+
+ /* Test for unknown errors */
+ if (ret != 0 && ret != -EUCLEAN && ret != -EBADMSG) {
+ dbg("read of block %d at zone %d, failed due to error (%d)",
+ block, zone, ret);
+ goto again;
+ }
+
+ /* Do a basic test on the oob, to guard against returned garbage */
+ if (oob->reserved != 0xFFFFFFFF)
+ goto again;
+
+ /* This should never happen, unless there is a bug in the mtd driver */
+ WARN_ON(ops.oobretlen != SM_OOB_SIZE);
+ WARN_ON(buffer && ops.retlen != SM_SECTOR_SIZE);
+
+ if (!buffer)
+ return 0;
+
+ /* Test if sector marked as bad */
+ if (!sm_sector_valid(oob)) {
+ dbg("read of block %d at zone %d, failed because it is marked"
+ " as bad" , block, zone);
+ goto again;
+ }
+
+ /* Test ECC*/
+ if (ret == -EBADMSG ||
+ (ftl->smallpagenand && sm_correct_sector(buffer, oob))) {
+
+ dbg("read of block %d at zone %d, failed due to ECC error",
+ block, zone);
+ goto again;
+ }
+
+ return 0;
+}
+
+/* Writes a sector to media */
+static int sm_write_sector(struct sm_ftl *ftl,
+ int zone, int block, int boffset,
+ u8 *buffer, struct sm_oob *oob)
+{
+ struct mtd_oob_ops ops;
+ struct mtd_info *mtd = ftl->trans->mtd;
+ int ret;
+
+ BUG_ON(ftl->readonly);
+
+ if (zone == 0 && (block == ftl->cis_block || block == 0)) {
+ dbg("attempted to write the CIS!");
+ return -EIO;
+ }
+
+ if (ftl->unstable)
+ return -EIO;
+
+ ops.mode = ftl->smallpagenand ? MTD_OOB_RAW : MTD_OOB_PLACE;
+ ops.len = SM_SECTOR_SIZE;
+ ops.datbuf = buffer;
+ ops.ooboffs = 0;
+ ops.ooblen = SM_OOB_SIZE;
+ ops.oobbuf = (void *)oob;
+
+ ret = mtd->write_oob(mtd, sm_mkoffset(ftl, zone, block, boffset), &ops);
+
+ /* Now we assume that hardware will catch write bitflip errors */
+ /* If you are paranoid, use CONFIG_MTD_NAND_VERIFY_WRITE */
+
+ if (ret) {
+ dbg("write to block %d at zone %d, failed with error %d",
+ block, zone, ret);
+
+ sm_recheck_media(ftl);
+ return ret;
+ }
+
+ /* This should never happen, unless there is a bug in the driver */
+ WARN_ON(ops.oobretlen != SM_OOB_SIZE);
+ WARN_ON(buffer && ops.retlen != SM_SECTOR_SIZE);
+
+ return 0;
+}
+
+/* ------------------------ block IO ------------------------------------- */
+
+/* Write a block using data and lba, and invalid sector bitmap */
+static int sm_write_block(struct sm_ftl *ftl, u8 *buf,
+ int zone, int block, int lba,
+ unsigned long invalid_bitmap)
+{
+ struct sm_oob oob;
+ int boffset;
+ int retry = 0;
+
+ /* Initialize the oob with requested values */
+ memset(&oob, 0xFF, SM_OOB_SIZE);
+ sm_write_lba(&oob, lba);
+restart:
+ for (boffset = 0; boffset < ftl->block_size;
+ boffset += SM_SECTOR_SIZE) {
+
+ oob.data_status = 0xFF;
+
+ if (test_bit(boffset / SM_SECTOR_SIZE, &invalid_bitmap)) {
+
+ sm_printk("sector %d of block at LBA %d of zone %d"
+ " coudn't be read, marking it as invalid",
+ boffset / SM_SECTOR_SIZE, lba, zone);
+
+ oob.data_status = 0;
+ }
+
+#ifdef CONFIG_SM_FTL_MUSEUM
+ if (ftl->smallpagenand) {
+ __nand_calculate_ecc(buf + boffset,
+ SM_SMALL_PAGE, oob.ecc1);
+
+ __nand_calculate_ecc(buf + boffset + SM_SMALL_PAGE,
+ SM_SMALL_PAGE, oob.ecc2);
+ }
+#endif
+ if (!sm_write_sector(ftl, zone, block, boffset,
+ buf + boffset, &oob))
+ continue;
+
+ if (!retry) {
+
+ /* If write fails. try to erase the block */
+ /* This is safe, because we never write in blocks
+ that contain valuable data.
+ This is intended to repair block that are marked
+ as erased, but that isn't fully erased*/
+
+ if (sm_erase_block(ftl, zone, block, 0))
+ return -EIO;
+
+ retry = 1;
+ goto restart;
+ } else {
+ sm_mark_block_bad(ftl, zone, block);
+ return -EIO;
+ }
+ }
+ return 0;
+}
+
+
+/* Mark whole block at offset 'offs' as bad. */
+static void sm_mark_block_bad(struct sm_ftl *ftl, int zone, int block)
+{
+ struct sm_oob oob;
+ int boffset;
+
+ memset(&oob, 0xFF, SM_OOB_SIZE);
+ oob.block_status = 0xF0;
+
+ if (ftl->unstable)
+ return;
+
+ if (sm_recheck_media(ftl))
+ return;
+
+ sm_printk("marking block %d of zone %d as bad", block, zone);
+
+ /* We aren't checking the return value, because we don't care */
+ /* This also fails on fake xD cards, but I guess these won't expose
+ any bad blocks till fail completly */
+ for (boffset = 0; boffset < ftl->block_size; boffset += SM_SECTOR_SIZE)
+ sm_write_sector(ftl, zone, block, boffset, NULL, &oob);
+}
+
+/*
+ * Erase a block within a zone
+ * If erase succedes, it updates free block fifo, otherwise marks block as bad
+ */
+static int sm_erase_block(struct sm_ftl *ftl, int zone_num, u16 block,
+ int put_free)
+{
+ struct ftl_zone *zone = &ftl->zones[zone_num];
+ struct mtd_info *mtd = ftl->trans->mtd;
+ struct erase_info erase;
+
+ erase.mtd = mtd;
+ erase.callback = sm_erase_callback;
+ erase.addr = sm_mkoffset(ftl, zone_num, block, 0);
+ erase.len = ftl->block_size;
+ erase.priv = (u_long)ftl;
+
+ if (ftl->unstable)
+ return -EIO;
+
+ BUG_ON(ftl->readonly);
+
+ if (zone_num == 0 && (block == ftl->cis_block || block == 0)) {
+ sm_printk("attempted to erase the CIS!");
+ return -EIO;
+ }
+
+ if (mtd->erase(mtd, &erase)) {
+ sm_printk("erase of block %d in zone %d failed",
+ block, zone_num);
+ goto error;
+ }
+
+ if (erase.state == MTD_ERASE_PENDING)
+ wait_for_completion(&ftl->erase_completion);
+
+ if (erase.state != MTD_ERASE_DONE) {
+ sm_printk("erase of block %d in zone %d failed after wait",
+ block, zone_num);
+ goto error;
+ }
+
+ if (put_free)
+ kfifo_in(&zone->free_sectors,
+ (const unsigned char *)&block, sizeof(block));
+
+ return 0;
+error:
+ sm_mark_block_bad(ftl, zone_num, block);
+ return -EIO;
+}
+
+static void sm_erase_callback(struct erase_info *self)
+{
+ struct sm_ftl *ftl = (struct sm_ftl *)self->priv;
+ complete(&ftl->erase_completion);
+}
+
+/* Throughtly test that block is valid. */
+static int sm_check_block(struct sm_ftl *ftl, int zone, int block)
+{
+ int boffset;
+ struct sm_oob oob;
+ int lbas[] = { -3, 0, 0, 0 };
+ int i = 0;
+ int test_lba;
+
+
+ /* First just check that block doesn't look fishy */
+ /* Only blocks that are valid or are sliced in two parts, are
+ accepted */
+ for (boffset = 0; boffset < ftl->block_size;
+ boffset += SM_SECTOR_SIZE) {
+
+ /* This shoudn't happen anyway */
+ if (sm_read_sector(ftl, zone, block, boffset, NULL, &oob))
+ return -2;
+
+ test_lba = sm_read_lba(&oob);
+
+ if (lbas[i] != test_lba)
+ lbas[++i] = test_lba;
+
+ /* If we found three different LBAs, something is fishy */
+ if (i == 3)
+ return -EIO;
+ }
+
+ /* If the block is sliced (partialy erased usually) erase it */
+ if (i == 2) {
+ sm_erase_block(ftl, zone, block, 1);
+ return 1;
+ }
+
+ return 0;
+}
+
+/* ----------------- media scanning --------------------------------- */
+static const struct chs_entry chs_table[] = {
+ { 1, 125, 4, 4 },
+ { 2, 125, 4, 8 },
+ { 4, 250, 4, 8 },
+ { 8, 250, 4, 16 },
+ { 16, 500, 4, 16 },
+ { 32, 500, 8, 16 },
+ { 64, 500, 8, 32 },
+ { 128, 500, 16, 32 },
+ { 256, 1000, 16, 32 },
+ { 512, 1015, 32, 63 },
+ { 1024, 985, 33, 63 },
+ { 2048, 985, 33, 63 },
+ { 0 },
+};
+
+
+static const u8 cis_signature[] = {
+ 0x01, 0x03, 0xD9, 0x01, 0xFF, 0x18, 0x02, 0xDF, 0x01, 0x20
+};
+/* Find out media parameters.
+ * This ideally has to be based on nand id, but for now device size is enough */
+int sm_get_media_info(struct sm_ftl *ftl, struct mtd_info *mtd)
+{
+ int i;
+ int size_in_megs = mtd->size / (1024 * 1024);
+
+ ftl->readonly = mtd->type == MTD_ROM;
+
+ /* Manual settings for very old devices */
+ ftl->zone_count = 1;
+ ftl->smallpagenand = 0;
+
+ switch (size_in_megs) {
+ case 1:
+ /* 1 Mb flash/rom SmartMedia card (256 byte pages)*/
+ ftl->zone_size = 256;
+ ftl->max_lba = 250;
+ ftl->block_size = 8 * SM_SECTOR_SIZE;
+ ftl->smallpagenand = 1;
+
+ break;
+ case 2:
+ /* 2 Mb flash SmartMedia (256 byte pages)*/
+ if (mtd->writesize == SM_SMALL_PAGE) {
+ ftl->zone_size = 512;
+ ftl->max_lba = 500;
+ ftl->block_size = 8 * SM_SECTOR_SIZE;
+ ftl->smallpagenand = 1;
+ /* 2 Mb rom SmartMedia */
+ } else {
+
+ if (!ftl->readonly)
+ return -ENODEV;
+
+ ftl->zone_size = 256;
+ ftl->max_lba = 250;
+ ftl->block_size = 16 * SM_SECTOR_SIZE;
+ }
+ break;
+ case 4:
+ /* 4 Mb flash/rom SmartMedia device */
+ ftl->zone_size = 512;
+ ftl->max_lba = 500;
+ ftl->block_size = 16 * SM_SECTOR_SIZE;
+ break;
+ case 8:
+ /* 8 Mb flash/rom SmartMedia device */
+ ftl->zone_size = 1024;
+ ftl->max_lba = 1000;
+ ftl->block_size = 16 * SM_SECTOR_SIZE;
+ }
+
+ /* Minimum xD size is 16M. Also, all xD cards have standard zone
+ sizes. SmartMedia cards exist up to 128 Mb and have same layout*/
+ if (size_in_megs >= 16) {
+ ftl->zone_count = size_in_megs / 16;
+ ftl->zone_size = 1024;
+ ftl->max_lba = 1000;
+ ftl->block_size = 32 * SM_SECTOR_SIZE;
+ }
+
+ /* Test for proper write,erase and oob sizes */
+ if (mtd->erasesize > ftl->block_size)
+ return -ENODEV;
+
+ if (mtd->writesize > SM_SECTOR_SIZE)
+ return -ENODEV;
+
+ if (ftl->smallpagenand && mtd->oobsize < SM_SMALL_OOB_SIZE)
+ return -ENODEV;
+
+ if (!ftl->smallpagenand && mtd->oobsize < SM_OOB_SIZE)
+ return -ENODEV;
+
+ /* We use these functions for IO */
+ if (!mtd->read_oob || !mtd->write_oob)
+ return -ENODEV;
+
+ /* Find geometry information */
+ for (i = 0 ; i < ARRAY_SIZE(chs_table) ; i++) {
+ if (chs_table[i].size == size_in_megs) {
+ ftl->cylinders = chs_table[i].cyl;
+ ftl->heads = chs_table[i].head;
+ ftl->sectors = chs_table[i].sec;
+ return 0;
+ }
+ }
+
+ sm_printk("media has unknown size : %dMB", size_in_megs);
+ ftl->cylinders = 985;
+ ftl->heads = 33;
+ ftl->sectors = 63;
+ return 0;
+}
+
+/* Validate the CIS */
+static int sm_read_cis(struct sm_ftl *ftl)
+{
+ struct sm_oob oob;
+
+ if (sm_read_sector(ftl,
+ 0, ftl->cis_block, ftl->cis_boffset, ftl->cis_buffer, &oob))
+ return -EIO;
+
+ if (!sm_sector_valid(&oob) || !sm_block_valid(&oob))
+ return -EIO;
+
+ if (!memcmp(ftl->cis_buffer, cis_signature, sizeof(cis_signature)))
+ return 0;
+
+ if (!memcmp(ftl->cis_buffer + SM_SMALL_PAGE, cis_signature,
+ sizeof(cis_signature)))
+ return 0;
+ return -EIO;
+}
+
+/* Scan the media for the CIS */
+static int sm_find_cis(struct sm_ftl *ftl)
+{
+ struct sm_oob oob;
+ int block, boffset;
+ int block_found = 0;
+
+ /* Search for first valid block */
+ for (block = 0 ; block < ftl->zone_size - ftl->max_lba ; block++) {
+
+ if (sm_read_sector(ftl, 0, block, 0, NULL, &oob))
+ continue;
+
+ if (!sm_block_valid(&oob))
+ continue;
+ block_found = 1;
+ break;
+ }
+
+ if (!block_found)
+ return -EIO;
+
+ /* Search for first valid sector in this block */
+ for (boffset = 0 ; boffset < ftl->block_size;
+ boffset += SM_SECTOR_SIZE) {
+
+ if (sm_read_sector(ftl, 0, block, boffset, NULL, &oob))
+ continue;
+
+ if (!sm_sector_valid(&oob))
+ continue;
+ break;
+ }
+
+ if (boffset == ftl->block_size)
+ return -EIO;
+
+ ftl->cis_block = block;
+ ftl->cis_boffset = boffset;
+
+ if (!sm_read_cis(ftl)) {
+ dbg("CIS block found at offset %d",
+ block * ftl->block_size + boffset);
+ return 0;
+ }
+
+ return -EIO;
+}
+
+/* Basic test to determine if underlying mtd device if functional */
+static int sm_recheck_media(struct sm_ftl *ftl)
+{
+ if (sm_read_cis(ftl)) {
+
+ if (!ftl->unstable) {
+ sm_printk("media unstable, not allowing writes");
+ ftl->unstable = 1;
+ }
+ return -EIO;
+ }
+ return 0;
+}
+
+/* Initialize a FTL zone */
+static int sm_init_zone(struct sm_ftl *ftl, int zone_num)
+{
+ struct ftl_zone *zone = &ftl->zones[zone_num];
+ struct sm_oob oob;
+ u16 block;
+ int lba;
+ int i = 0;
+
+ dbg("initializing zone %d", zone_num);
+
+ /* Allocate memory for FTL table */
+ zone->lba_to_phys_table = kmalloc(ftl->max_lba * 2, GFP_KERNEL);
+
+ if (!zone->lba_to_phys_table)
+ return -ENOMEM;
+ memset(zone->lba_to_phys_table, -1, ftl->max_lba * 2);
+
+
+ /* Allocate memory for free sectors FIFO */
+ if (kfifo_alloc(&zone->free_sectors, ftl->zone_size * 2, GFP_KERNEL)) {
+ kfree(zone->lba_to_phys_table);
+ return -ENOMEM;
+ }
+
+ /* Now scan the zone */
+ for (block = 0 ; block < ftl->zone_size ; block++) {
+
+ /* Skip blocks till the CIS (including) */
+ if (zone_num == 0 && block <= ftl->cis_block)
+ continue;
+
+ /* Read the oob of first sector */
+ if (sm_read_sector(ftl, zone_num, block, 0, NULL, &oob))
+ return -EIO;
+
+ /* Test to see if block is erased. It is enough to test
+ first sector, because erase happens in one shot */
+ if (sm_block_erased(&oob)) {
+ kfifo_in(&zone->free_sectors,
+ (unsigned char *)&block, 2);
+ continue;
+ }
+
+ /* If block is marked as bad, skip it */
+ /* This assumes we can trust first sector*/
+ /* However the way the block valid status is defined, ensures
+ very low probability of failure here */
+ if (!sm_block_valid(&oob)) {
+ dbg("PH %04d <-> <marked bad>", block);
+ continue;
+ }
+
+
+ lba = sm_read_lba(&oob);
+
+ /* Invalid LBA means that block is damaged. */
+ /* We can try to erase it, or mark it as bad, but
+ lets leave that to recovery application */
+ if (lba == -2 || lba >= ftl->max_lba) {
+ dbg("PH %04d <-> LBA %04d(bad)", block, lba);
+ continue;
+ }
+
+
+ /* If there is no collision,
+ just put the sector in the FTL table */
+ if (zone->lba_to_phys_table[lba] < 0) {
+ dbg("PH %04d <-> LBA %04d", block, lba);
+ zone->lba_to_phys_table[lba] = block;
+ continue;
+ }
+
+ sm_printk("collision"
+ " of LBA %d between blocks %d and %d in zone %d",
+ lba, zone->lba_to_phys_table[lba], block, zone_num);
+
+ /* Test that this block is valid*/
+ if (sm_check_block(ftl, zone_num, block))
+ continue;
+
+ /* Test now the old block */
+ if (sm_check_block(ftl, zone_num,
+ zone->lba_to_phys_table[lba])) {
+ zone->lba_to_phys_table[lba] = block;
+ continue;
+ }
+
+ /* If both blocks are valid and share same LBA, it means that
+ they hold different versions of same data. It not
+ known which is more recent, thus just erase one of them
+ */
+ sm_printk("both blocks are valid, erasing the later");
+ sm_erase_block(ftl, zone_num, block, 1);
+ }
+
+ dbg("zone initialized");
+ zone->initialized = 1;
+
+ /* No free sectors, means that the zone is heavily damaged, write won't
+ work, but it can still can be (partially) read */
+ if (!kfifo_len(&zone->free_sectors)) {
+ sm_printk("no free blocks in zone %d", zone_num);
+ return 0;
+ }
+
+ /* Randomize first block we write to */
+ get_random_bytes(&i, 2);
+ i %= (kfifo_len(&zone->free_sectors) / 2);
+
+ while (i--) {
+ kfifo_out(&zone->free_sectors, (unsigned char *)&block, 2);
+ kfifo_in(&zone->free_sectors, (const unsigned char *)&block, 2);
+ }
+ return 0;
+}
+
+/* Get and automaticly initialize an FTL mapping for one zone */
+struct ftl_zone *sm_get_zone(struct sm_ftl *ftl, int zone_num)
+{
+ struct ftl_zone *zone;
+ int error;
+
+ BUG_ON(zone_num >= ftl->zone_count);
+ zone = &ftl->zones[zone_num];
+
+ if (!zone->initialized) {
+ error = sm_init_zone(ftl, zone_num);
+
+ if (error)
+ return ERR_PTR(error);
+ }
+ return zone;
+}
+
+
+/* ----------------- cache handling ------------------------------------------*/
+
+/* Initialize the one block cache */
+void sm_cache_init(struct sm_ftl *ftl)
+{
+ ftl->cache_data_invalid_bitmap = 0xFFFFFFFF;
+ ftl->cache_clean = 1;
+ ftl->cache_zone = -1;
+ ftl->cache_block = -1;
+ /*memset(ftl->cache_data, 0xAA, ftl->block_size);*/
+}
+
+/* Put sector in one block cache */
+void sm_cache_put(struct sm_ftl *ftl, char *buffer, int boffset)
+{
+ memcpy(ftl->cache_data + boffset, buffer, SM_SECTOR_SIZE);
+ clear_bit(boffset / SM_SECTOR_SIZE, &ftl->cache_data_invalid_bitmap);
+ ftl->cache_clean = 0;
+}
+
+/* Read a sector from the cache */
+int sm_cache_get(struct sm_ftl *ftl, char *buffer, int boffset)
+{
+ if (test_bit(boffset / SM_SECTOR_SIZE,
+ &ftl->cache_data_invalid_bitmap))
+ return -1;
+
+ memcpy(buffer, ftl->cache_data + boffset, SM_SECTOR_SIZE);
+ return 0;
+}
+
+/* Write the cache to hardware */
+int sm_cache_flush(struct sm_ftl *ftl)
+{
+ struct ftl_zone *zone;
+
+ int sector_num;
+ u16 write_sector;
+ int zone_num = ftl->cache_zone;
+ int block_num;
+
+ if (ftl->cache_clean)
+ return 0;
+
+ if (ftl->unstable)
+ return -EIO;
+
+ BUG_ON(zone_num < 0);
+ zone = &ftl->zones[zone_num];
+ block_num = zone->lba_to_phys_table[ftl->cache_block];
+
+
+ /* Try to read all unread areas of the cache block*/
+ for_each_bit(sector_num, &ftl->cache_data_invalid_bitmap,
+ ftl->block_size / SM_SECTOR_SIZE) {
+
+ if (!sm_read_sector(ftl,
+ zone_num, block_num, sector_num * SM_SECTOR_SIZE,
+ ftl->cache_data + sector_num * SM_SECTOR_SIZE, NULL))
+ clear_bit(sector_num,
+ &ftl->cache_data_invalid_bitmap);
+ }
+restart:
+ /* No spare blocks */
+ /* We could still continue by erasing the current block,
+ but for such worn out media it doesn't worth the trouble,
+ and the dangers */
+
+ if (!kfifo_len(&zone->free_sectors)) {
+ dbg("no free sectors for write!");
+ return -EIO;
+ }
+
+ kfifo_out(&zone->free_sectors, (unsigned char *)&write_sector, 2);
+
+ if (sm_write_block(ftl, ftl->cache_data, zone_num, write_sector,
+ ftl->cache_block, ftl->cache_data_invalid_bitmap))
+ goto restart;
+
+ /* Update the FTL table */
+ zone->lba_to_phys_table[ftl->cache_block] = write_sector;
+
+ /* Write succesfull, so erase and free the old block */
+ if (block_num > 0)
+ sm_erase_block(ftl, zone_num, block_num, 1);
+
+ sm_cache_init(ftl);
+ return 0;
+}
+
+
+/* flush timer, runs a second after last write */
+static void sm_cache_flush_timer(unsigned long data)
+{
+ struct sm_ftl *ftl = (struct sm_ftl *)data;
+ queue_work(cache_flush_workqueue, &ftl->flush_work);
+}
+
+/* cache flush work, kicked by timer */
+static void sm_cache_flush_work(struct work_struct *work)
+{
+ struct sm_ftl *ftl = container_of(work, struct sm_ftl, flush_work);
+ mutex_lock(&ftl->mutex);
+ sm_cache_flush(ftl);
+ mutex_unlock(&ftl->mutex);
+ return;
+}
+
+/* ---------------- outside interface -------------------------------------- */
+
+/* outside interface: read a sector */
+static int sm_read(struct mtd_blktrans_dev *dev,
+ unsigned long sect_no, char *buf)
+{
+ struct sm_ftl *ftl = dev->priv;
+ struct ftl_zone *zone;
+ int error = 0, in_cache = 0;
+ int zone_num, block, boffset;
+
+ sm_break_offset(ftl, sect_no << 9, &zone_num, &block, &boffset);
+ mutex_lock(&ftl->mutex);
+
+
+ zone = sm_get_zone(ftl, zone_num);
+ if (IS_ERR(zone)) {
+ error = PTR_ERR(zone);
+ goto unlock;
+ }
+
+ /* Have to look at cache first */
+ if (ftl->cache_zone == zone_num && ftl->cache_block == block) {
+ in_cache = 1;
+ if (!sm_cache_get(ftl, buf, boffset))
+ goto unlock;
+ }
+
+ /* Translate the block and return if doesn't exist in the table */
+ block = zone->lba_to_phys_table[block];
+
+ if (block == -1) {
+ memset(buf, 0xFF, SM_SECTOR_SIZE);
+ goto unlock;
+ }
+
+ if (sm_read_sector(ftl, zone_num, block, boffset, buf, NULL)) {
+ error = -EIO;
+ goto unlock;
+ }
+
+ if (in_cache)
+ sm_cache_put(ftl, buf, boffset);
+unlock:
+ mutex_unlock(&ftl->mutex);
+ return error;
+}
+
+/* outside interface: write a sector */
+static int sm_write(struct mtd_blktrans_dev *dev,
+ unsigned long sec_no, char *buf)
+{
+ struct sm_ftl *ftl = dev->priv;
+ struct ftl_zone *zone;
+ int error, zone_num, block, boffset;
+
+ BUG_ON(ftl->readonly);
+ sm_break_offset(ftl, sec_no << 9, &zone_num, &block, &boffset);
+
+ /* No need in flush thread running now */
+ del_timer(&ftl->timer);
+ mutex_lock(&ftl->mutex);
+
+ zone = sm_get_zone(ftl, zone_num);
+ if (IS_ERR(zone)) {
+ error = PTR_ERR(zone);
+ goto unlock;
+ }
+
+ /* If entry is not in cache, flush it */
+ if (ftl->cache_block != block || ftl->cache_zone != zone_num) {
+
+ error = sm_cache_flush(ftl);
+ if (error)
+ goto unlock;
+
+ ftl->cache_block = block;
+ ftl->cache_zone = zone_num;
+ }
+
+ sm_cache_put(ftl, buf, boffset);
+unlock:
+ mod_timer(&ftl->timer, jiffies + msecs_to_jiffies(cache_timeout));
+ mutex_unlock(&ftl->mutex);
+ return error;
+}
+
+/* outside interface: flush everything */
+static int sm_flush(struct mtd_blktrans_dev *dev)
+{
+ struct sm_ftl *ftl = dev->priv;
+ int retval;
+
+ mutex_lock(&ftl->mutex);
+ retval = sm_cache_flush(ftl);
+ mutex_unlock(&ftl->mutex);
+ return retval;
+}
+
+/* outside interface: device is released */
+static int sm_release(struct mtd_blktrans_dev *dev)
+{
+ struct sm_ftl *ftl = dev->priv;
+
+ mutex_lock(&ftl->mutex);
+ del_timer_sync(&ftl->timer);
+ cancel_work_sync(&ftl->flush_work);
+ sm_cache_flush(ftl);
+ mutex_unlock(&ftl->mutex);
+ return 0;
+}
+
+/* outside interface: get geometry */
+static int sm_getgeo(struct mtd_blktrans_dev *dev, struct hd_geometry *geo)
+{
+ struct sm_ftl *ftl = dev->priv;
+ geo->heads = ftl->heads;
+ geo->sectors = ftl->sectors;
+ geo->cylinders = ftl->cylinders;
+ return 0;
+}
+
+/* external interface: main initialization function */
+static void sm_add_mtd(struct mtd_blktrans_ops *tr, struct mtd_info *mtd)
+{
+ struct mtd_blktrans_dev *trans;
+ struct sm_ftl *ftl;
+
+ /* Allocate & initialize our private structure */
+ ftl = kzalloc(sizeof(struct sm_ftl), GFP_KERNEL);
+ if (!ftl)
+ goto error1;
+
+ mutex_init(&ftl->mutex);
+ setup_timer(&ftl->timer, sm_cache_flush_timer, (unsigned long)ftl);
+ INIT_WORK(&ftl->flush_work, sm_cache_flush_work);
+ init_completion(&ftl->erase_completion);
+
+
+ /* Read media information */
+ if (sm_get_media_info(ftl, mtd))
+ goto error2;
+
+ /* Allocate temporary CIS buffer for read retry support */
+ ftl->cis_buffer = kzalloc(SM_SECTOR_SIZE, GFP_KERNEL);
+ if (!ftl->cis_buffer)
+ goto error2;
+
+ /* Allocate zone array, it will be initialized on demand */
+ ftl->zones = kzalloc(sizeof(struct ftl_zone) * ftl->zone_count,
+ GFP_KERNEL);
+ if (!ftl->zones)
+ goto error3;
+
+ /* Allocate the cache*/
+ ftl->cache_data = kzalloc(ftl->block_size, GFP_KERNEL);
+
+ if (!ftl->cache_data)
+ goto error4;
+
+ sm_cache_init(ftl);
+
+ /* Allocate upper layer structure and initialize it */
+ trans = kzalloc(sizeof(struct mtd_blktrans_dev), GFP_KERNEL);
+ if (!trans)
+ goto error5;
+
+ ftl->trans = trans;
+ trans->priv = ftl;
+
+ trans->tr = tr;
+ trans->mtd = mtd;
+ trans->devnum = -1;
+ trans->size = (ftl->block_size * ftl->max_lba * ftl->zone_count) >> 9;
+ trans->readonly = ftl->readonly;
+
+
+ if (sm_find_cis(ftl))
+ goto error6;
+
+ trans->disk_attributes = sm_create_sysfs_attributes(ftl);
+
+ sm_printk("Found %d MiB %s FTL on mtd%d",
+ (int)(mtd->size / (1024 * 1024)),
+ mtd->technology == MTD_TECHNOLOGY_XD ? "xD" : "SmartMedia",
+ mtd->index);
+
+ dbg("FTL layout:");
+ dbg("%d zone(s), each consists of %d blocks (+%d spares)",
+ ftl->zone_count, ftl->max_lba,
+ ftl->zone_size - ftl->max_lba);
+ dbg("each block consists of %d bytes",
+ ftl->block_size);
+
+ /* Register device*/
+ if (add_mtd_blktrans_dev(trans))
+ goto error6;
+
+ return;
+error6:
+ kfree(trans);
+error5:
+ kfree(ftl->cache_data);
+error4:
+ kfree(ftl->zones);
+error3:
+ kfree(ftl->cis_buffer);
+error2:
+ kfree(ftl);
+error1:
+ return;
+}
+
+/* main interface: device {surprise,} removal */
+static void sm_remove_dev(struct mtd_blktrans_dev *dev)
+{
+ struct sm_ftl *ftl = dev->priv;
+ int i;
+
+ del_mtd_blktrans_dev(dev);
+
+ for (i = 0 ; i < ftl->zone_count; i++) {
+
+ if (!ftl->zones[i].initialized)
+ continue;
+
+ kfree(ftl->zones[i].lba_to_phys_table);
+ kfifo_free(&ftl->zones[i].free_sectors);
+ }
+
+ sm_delete_sysfs_attributes(ftl);
+ kfree(ftl->zones);
+ kfree(ftl->cache_data);
+ kfree(ftl);
+}
+
+static struct mtd_blktrans_ops sm_ftl_ops = {
+ .name = "smblk",
+ .major = -1,
+ .part_bits = SM_FTL_PARTN_BITS,
+ .blksize = SM_SECTOR_SIZE,
+ .getgeo = sm_getgeo,
+
+ .add_mtd = sm_add_mtd,
+ .remove_dev = sm_remove_dev,
+
+ .readsect = sm_read,
+ .writesect = sm_write,
+
+ .flush = sm_flush,
+ .release = sm_release,
+
+ .owner = THIS_MODULE,
+};
+
+static __init int sm_module_init(void)
+{
+ int error = 0;
+ cache_flush_workqueue = create_freezeable_workqueue("smflush");
+
+ if (IS_ERR(cache_flush_workqueue))
+ return PTR_ERR(cache_flush_workqueue);
+
+ error = register_mtd_blktrans(&sm_ftl_ops);
+ if (error)
+ destroy_workqueue(cache_flush_workqueue);
+ return error;
+
+}
+
+static void __exit sm_module_exit(void)
+{
+ destroy_workqueue(cache_flush_workqueue);
+ deregister_mtd_blktrans(&sm_ftl_ops);
+}
+
+module_init(sm_module_init);
+module_exit(sm_module_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Maxim Levitsky <[email protected]>");
+MODULE_DESCRIPTION("Smartmedia/xD mtd translation layer");
diff --git a/drivers/mtd/sm_ftl.h b/drivers/mtd/sm_ftl.h
new file mode 100644
index 0000000..e3941f4
--- /dev/null
+++ b/drivers/mtd/sm_ftl.h
@@ -0,0 +1,92 @@
+/*
+ * Copyright (C) 2009 - Maxim Levitsky
+ * SmartMedia/xD translation layer
+ *
+ * Based loosly on ssfdc.c which is
+ * (c) 2005 Eptar srl
+ * Author: Claudio Lanconelli <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/mtd/blktrans.h>
+#include <linux/kfifo.h>
+#include <linux/sched.h>
+#include <linux/completion.h>
+
+
+
+struct ftl_zone {
+ int initialized;
+ s16 *lba_to_phys_table; /* LBA to physical table */
+ struct kfifo free_sectors; /* queue of free sectors */
+};
+
+struct sm_ftl {
+ struct mtd_blktrans_dev *trans;
+
+ struct mutex mutex; /* protects the structure */
+ struct ftl_zone *zones; /* FTL tables for each zone */
+
+ /* Media information */
+ int block_size; /* block size in bytes */
+ int zone_size; /* zone size in blocks */
+ int zone_count; /* number of zones */
+ int max_lba; /* maximum lba in a zone */
+ int smallpagenand; /* 256 bytes/page nand */
+ int readonly; /* is FS readonly */
+ int unstable;
+ int cis_block; /* CIS block location */
+ int cis_boffset; /* CIS offset in the block */
+ void *cis_buffer; /* tmp buffer for cis reads */
+
+ /* Cache */
+ int cache_block; /* block number of cached block */
+ int cache_zone; /* zone of cached block */
+ unsigned char *cache_data; /* cached block data */
+ long unsigned int cache_data_invalid_bitmap;
+ int cache_clean;
+ struct work_struct flush_work;
+ struct timer_list timer;
+
+ /* Async erase stuff */
+ struct completion erase_completion;
+
+ /* Geometry stuff */
+ int heads;
+ int sectors;
+ int cylinders;
+};
+
+struct chs_entry {
+ unsigned long size;
+ unsigned short cyl;
+ unsigned char head;
+ unsigned char sec;
+};
+
+
+#define SM_FTL_PARTN_BITS 3
+
+#define sm_printk(format, ...) \
+ printk(KERN_WARNING "sm_ftl" ": " format "\n", ## __VA_ARGS__)
+
+
+#ifdef __DEBUG
+
+#define dbg(format, ...) \
+ printk(KERN_DEBUG "sm_ftl" ": " format "\n", ## __VA_ARGS__)
+#else
+
+#define dbg(format, ...)
+
+#endif
+
+static void sm_erase_callback(struct erase_info *self);
+static int sm_erase_block(struct sm_ftl *ftl, int zone_num, u16 block,
+ int put_free);
+static void sm_mark_block_bad(struct sm_ftl *ftl, int zone_num, int block);
+
+static int sm_recheck_media(struct sm_ftl *ftl);
--
1.6.3.3
This is the biggest change. To make hotplug possible, and this layer clearer, now
mtd_blktrans_dev contains everything for a single mtd block translation device.
Also removed some very old leftovers
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/mtd_blkdevs.c | 123 ++++++++++++++++++++----------------------
include/linux/mtd/blktrans.h | 10 ++--
2 files changed, 64 insertions(+), 69 deletions(-)
diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c
index c82e09b..93c87af 100644
--- a/drivers/mtd/mtd_blkdevs.c
+++ b/drivers/mtd/mtd_blkdevs.c
@@ -26,11 +26,6 @@
static LIST_HEAD(blktrans_majors);
-struct mtd_blkcore_priv {
- struct task_struct *thread;
- struct request_queue *rq;
- spinlock_t queue_lock;
-};
static int do_blktrans_request(struct mtd_blktrans_ops *tr,
struct mtd_blktrans_dev *dev,
@@ -80,14 +75,13 @@ static int do_blktrans_request(struct mtd_blktrans_ops *tr,
static int mtd_blktrans_thread(void *arg)
{
- struct mtd_blktrans_ops *tr = arg;
- struct request_queue *rq = tr->blkcore_priv->rq;
+ struct mtd_blktrans_dev *dev = arg;
+ struct request_queue *rq = dev->rq;
struct request *req = NULL;
spin_lock_irq(rq->queue_lock);
while (!kthread_should_stop()) {
- struct mtd_blktrans_dev *dev;
int res;
if (!req && !(req = blk_fetch_request(rq))) {
@@ -98,13 +92,10 @@ static int mtd_blktrans_thread(void *arg)
continue;
}
- dev = req->rq_disk->private_data;
- tr = dev->tr;
-
spin_unlock_irq(rq->queue_lock);
mutex_lock(&dev->lock);
- res = do_blktrans_request(tr, dev, req);
+ res = do_blktrans_request(dev->tr, dev, req);
mutex_unlock(&dev->lock);
spin_lock_irq(rq->queue_lock);
@@ -123,8 +114,8 @@ static int mtd_blktrans_thread(void *arg)
static void mtd_blktrans_request(struct request_queue *rq)
{
- struct mtd_blktrans_ops *tr = rq->queuedata;
- wake_up_process(tr->blkcore_priv->thread);
+ struct mtd_blktrans_dev *dev = rq->queuedata;
+ wake_up_process(dev->thread);
}
@@ -214,6 +205,7 @@ int add_mtd_blktrans_dev(struct mtd_blktrans_dev *new)
struct mtd_blktrans_dev *d;
int last_devnum = -1;
struct gendisk *gd;
+ int ret;
if (mutex_trylock(&mtd_table_mutex)) {
mutex_unlock(&mtd_table_mutex);
@@ -239,12 +231,13 @@ int add_mtd_blktrans_dev(struct mtd_blktrans_dev *new)
}
last_devnum = d->devnum;
}
+
+ ret = -EBUSY;
if (new->devnum == -1)
new->devnum = last_devnum+1;
- if ((new->devnum << tr->part_bits) > 256) {
- return -EBUSY;
- }
+ if ((new->devnum << tr->part_bits) > 256)
+ goto error1;
list_add_tail(&new->list, &tr->devs);
added:
@@ -252,11 +245,16 @@ int add_mtd_blktrans_dev(struct mtd_blktrans_dev *new)
if (!tr->writesect)
new->readonly = 1;
+
+ /* Create gendisk */
+ ret = -ENOMEM;
gd = alloc_disk(1 << tr->part_bits);
- if (!gd) {
- list_del(&new->list);
- return -ENOMEM;
- }
+
+ if (!gd)
+ goto error2;
+
+ new->disk = gd;
+ gd->private_data = new;
gd->major = tr->major;
gd->first_minor = (new->devnum) << tr->part_bits;
gd->fops = &mtd_blktrans_ops;
@@ -274,13 +272,33 @@ int add_mtd_blktrans_dev(struct mtd_blktrans_dev *new)
snprintf(gd->disk_name, sizeof(gd->disk_name),
"%s%d", tr->name, new->devnum);
- /* 2.5 has capacity in units of 512 bytes while still
- having BLOCK_SIZE_BITS set to 10. Just to keep us amused. */
set_capacity(gd, (new->size * tr->blksize) >> 9);
- gd->private_data = new;
- new->blkcore_priv = gd;
- gd->queue = tr->blkcore_priv->rq;
+
+ /* Create the request queue */
+ spin_lock_init(&new->queue_lock);
+ new->rq = blk_init_queue(mtd_blktrans_request, &new->queue_lock);
+
+ if (!new->rq)
+ goto error3;
+
+ new->rq->queuedata = new;
+ blk_queue_logical_block_size(new->rq, tr->blksize);
+
+ if (tr->discard)
+ queue_flag_set_unlocked(QUEUE_FLAG_DISCARD,
+ new->rq);
+
+ gd->queue = new->rq;
+
+ /* Create processing thread */
+ /* TODO: workqueue ? */
+ new->thread = kthread_run(mtd_blktrans_thread, new,
+ "%s%d", tr->name, new->mtd->index);
+ if (IS_ERR(new->thread)) {
+ ret = PTR_ERR(new->thread);
+ goto error4;
+ }
gd->driverfs_dev = &new->mtd->dev;
if (new->readonly)
@@ -289,6 +307,15 @@ int add_mtd_blktrans_dev(struct mtd_blktrans_dev *new)
add_disk(gd);
return 0;
+error4:
+ blk_cleanup_queue(new->rq);
+error3:
+ put_disk(new->disk);
+error2:
+ list_del(&new->list);
+error1:
+ kfree(new);
+ return ret;
}
int del_mtd_blktrans_dev(struct mtd_blktrans_dev *old)
@@ -300,9 +327,13 @@ int del_mtd_blktrans_dev(struct mtd_blktrans_dev *old)
list_del(&old->list);
- del_gendisk(old->blkcore_priv);
- put_disk(old->blkcore_priv);
+ /* stop new requests to arrive */
+ del_gendisk(old->disk);
+
+ /* Stop the thread */
+ kthread_stop(old->thread);
+ blk_cleanup_queue(old->rq);
return 0;
}
@@ -343,9 +374,6 @@ int register_mtd_blktrans(struct mtd_blktrans_ops *tr)
if (!blktrans_notifier.list.next)
register_mtd_user(&blktrans_notifier);
- tr->blkcore_priv = kzalloc(sizeof(*tr->blkcore_priv), GFP_KERNEL);
- if (!tr->blkcore_priv)
- return -ENOMEM;
mutex_lock(&mtd_table_mutex);
@@ -353,39 +381,12 @@ int register_mtd_blktrans(struct mtd_blktrans_ops *tr)
if (ret) {
printk(KERN_WARNING "Unable to register %s block device on major %d: %d\n",
tr->name, tr->major, ret);
- kfree(tr->blkcore_priv);
mutex_unlock(&mtd_table_mutex);
return ret;
}
- spin_lock_init(&tr->blkcore_priv->queue_lock);
-
- tr->blkcore_priv->rq = blk_init_queue(mtd_blktrans_request, &tr->blkcore_priv->queue_lock);
- if (!tr->blkcore_priv->rq) {
- unregister_blkdev(tr->major, tr->name);
- kfree(tr->blkcore_priv);
- mutex_unlock(&mtd_table_mutex);
- return -ENOMEM;
- }
-
- tr->blkcore_priv->rq->queuedata = tr;
- blk_queue_logical_block_size(tr->blkcore_priv->rq, tr->blksize);
- if (tr->discard)
- queue_flag_set_unlocked(QUEUE_FLAG_DISCARD,
- tr->blkcore_priv->rq);
tr->blkshift = ffs(tr->blksize) - 1;
- tr->blkcore_priv->thread = kthread_run(mtd_blktrans_thread, tr,
- "%sd", tr->name);
- if (IS_ERR(tr->blkcore_priv->thread)) {
- ret = PTR_ERR(tr->blkcore_priv->thread);
- blk_cleanup_queue(tr->blkcore_priv->rq);
- unregister_blkdev(tr->major, tr->name);
- kfree(tr->blkcore_priv);
- mutex_unlock(&mtd_table_mutex);
- return ret;
- }
-
INIT_LIST_HEAD(&tr->devs);
list_add(&tr->list, &blktrans_majors);
@@ -405,8 +406,6 @@ int deregister_mtd_blktrans(struct mtd_blktrans_ops *tr)
mutex_lock(&mtd_table_mutex);
- /* Clean up the kernel thread */
- kthread_stop(tr->blkcore_priv->thread);
/* Remove it from the list of active majors */
list_del(&tr->list);
@@ -414,13 +413,9 @@ int deregister_mtd_blktrans(struct mtd_blktrans_ops *tr)
list_for_each_entry_safe(dev, next, &tr->devs, list)
tr->remove_dev(dev);
- blk_cleanup_queue(tr->blkcore_priv->rq);
unregister_blkdev(tr->major, tr->name);
-
mutex_unlock(&mtd_table_mutex);
- kfree(tr->blkcore_priv);
-
BUG_ON(!list_empty(&tr->devs));
return 0;
}
diff --git a/include/linux/mtd/blktrans.h b/include/linux/mtd/blktrans.h
index 8b4aa05..a4b3928 100644
--- a/include/linux/mtd/blktrans.h
+++ b/include/linux/mtd/blktrans.h
@@ -24,11 +24,13 @@ struct mtd_blktrans_dev {
int devnum;
unsigned long size;
int readonly;
- void *blkcore_priv; /* gendisk in 2.5, devfs_handle in 2.4 */
+ struct gendisk *disk;
+ struct task_struct *thread;
+ struct request_queue *rq;
+ spinlock_t queue_lock;
+ void *priv;
};
-struct blkcore_priv; /* Differs for 2.4 and 2.5 kernels; private */
-
struct mtd_blktrans_ops {
char *name;
int major;
@@ -60,8 +62,6 @@ struct mtd_blktrans_ops {
struct list_head devs;
struct list_head list;
struct module *owner;
-
- struct mtd_blkcore_priv *blkcore_priv;
};
extern int register_mtd_blktrans(struct mtd_blktrans_ops *tr);
--
1.6.3.3
Flush all requests, so we can be sure we don't deadlock the system later
when we remove the disk queue.
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/mtd_blkdevs.c | 14 +++++++++++++-
1 files changed, 13 insertions(+), 1 deletions(-)
diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c
index 841c6ae..a65eb07 100644
--- a/drivers/mtd/mtd_blkdevs.c
+++ b/drivers/mtd/mtd_blkdevs.c
@@ -115,7 +115,13 @@ static int mtd_blktrans_thread(void *arg)
static void mtd_blktrans_request(struct request_queue *rq)
{
struct mtd_blktrans_dev *dev = rq->queuedata;
- wake_up_process(dev->thread);
+ struct request *req = NULL;
+
+ if (dev->deleted)
+ while ((req = blk_fetch_request(rq)) != NULL)
+ __blk_end_request_all(req, -ENODEV);
+ else
+ wake_up_process(dev->thread);
}
@@ -358,6 +364,8 @@ error1:
int del_mtd_blktrans_dev(struct mtd_blktrans_dev *old)
{
+ unsigned long flags;
+
if (mutex_trylock(&mtd_table_mutex)) {
mutex_unlock(&mtd_table_mutex);
BUG();
@@ -368,7 +376,11 @@ int del_mtd_blktrans_dev(struct mtd_blktrans_dev *old)
/* stop new requests to arrive */
del_gendisk(old->disk);
+ /* flush current requests */
+ spin_lock_irqsave(&old->queue_lock, flags);
old->deleted = 1;
+ blk_start_queue(old->rq);
+ spin_unlock_irqrestore(&old->queue_lock, flags);
/* Stop the thread */
kthread_stop(old->thread);
--
1.6.3.3
This small module implements few helpers that are usefull
for nand drivers for SmartMedia/xD card readers.
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/nand/Kconfig | 9 +++
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/sm_common.c | 126 ++++++++++++++++++++++++++++++++++++++++++
drivers/mtd/nand/sm_common.h | 61 ++++++++++++++++++++
4 files changed, 197 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/nand/sm_common.c
create mode 100644 drivers/mtd/nand/sm_common.h
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 677cd53..13c1fb2 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -18,6 +18,10 @@ config MTD_NAND_VERIFY_WRITE
device thinks the write was successful, a bit could have been
flipped accidentally due to device wear or something else.
+config MTD_NAND_SMARTMEDIA
+ boolean
+ default n
+
config MTD_NAND_ECC_SMC
bool "NAND ECC Smart Media byte order"
default n
@@ -25,6 +29,11 @@ config MTD_NAND_ECC_SMC
Software ECC according to the Smart Media Specification.
The original Linux implementation had byte 0 and 1 swapped.
+config MTD_SM_COMMON
+ select MTD_NAND_SMARTMEDIA
+ tristate
+ default n
+
config MTD_NAND_MUSEUM_IDS
bool "Enable chip ids for obsolete ancient NAND devices"
depends on MTD_NAND
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 1407bd1..09891f6 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -4,6 +4,7 @@
obj-$(CONFIG_MTD_NAND) += nand.o nand_ecc.o
obj-$(CONFIG_MTD_NAND_IDS) += nand_ids.o
+obj-$(CONFIG_MTD_SM_COMMON) += sm_common.o
obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nand.o
obj-$(CONFIG_MTD_NAND_SPIA) += spia.o
diff --git a/drivers/mtd/nand/sm_common.c b/drivers/mtd/nand/sm_common.c
new file mode 100644
index 0000000..aa7e740
--- /dev/null
+++ b/drivers/mtd/nand/sm_common.c
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2009 - Maxim Levitsky
+ * Common routines & support for xD format
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+#include <linux/log2.h>
+#include "sm_common.h"
+
+static struct nand_ecclayout nand_oob_sm = {
+ .eccbytes = 6,
+ .eccpos = {8, 9, 10, 13, 14, 15},
+ .oobfree = {
+ {.offset = 0 , .length = 4}, /* reserved */
+ {.offset = 6 , .length = 2}, /* LBA1 */
+ {.offset = 11, .length = 2} /* LBA2 */
+ }
+};
+
+/* Tests if block (more correctly page) is bad */
+static int sm_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip)
+{
+ struct nand_chip *chip = (struct nand_chip *)mtd->priv;
+ struct mtd_oob_ops ops;
+ struct sm_oob oob;
+ int bad = 0, ret;
+
+ ops.mode = MTD_OOB_PLACE;
+ ops.ooboffs = 0;
+ ops.ooblen = SM_OOB_SIZE;
+ ops.oobbuf = (void *)&oob;
+ ops.datbuf = NULL;
+
+ if (getchip) {
+ nand_get_device(chip, mtd, FL_READING);
+ chip->select_chip(mtd, 0);
+ }
+
+ ret = nand_do_read_oob(mtd, ofs, &ops);
+ if (ret < 0 || ops.oobretlen != SM_OOB_SIZE)
+ goto out;
+
+ if (!sm_sector_valid(&oob) || !sm_block_valid(&oob)) {
+ bad = 1;
+ goto out;
+ }
+out:
+ if (getchip)
+ nand_release_device(mtd);
+ return bad;
+}
+
+/* Marks block as bad */
+static int sm_block_markbad(struct mtd_info *mtd, loff_t ofs)
+{
+ struct nand_chip *chip = (struct nand_chip *)mtd->priv;
+ struct mtd_oob_ops ops;
+ struct sm_oob oob;
+ int ret, error = 0;
+
+ memset(&oob, -1, SM_OOB_SIZE);
+ oob.data_status = 0;
+
+ ops.mode = MTD_OOB_PLACE;
+ ops.ooboffs = 0;
+ ops.ooblen = SM_OOB_SIZE;
+ ops.oobbuf = (void *)&oob;
+ ops.datbuf = NULL;
+
+ nand_get_device(chip, mtd, FL_WRITING);
+
+ ret = nand_do_write_oob(mtd, ofs, &ops);
+ if (ret < 0 || ops.oobretlen != SM_OOB_SIZE) {
+ printk(KERN_NOTICE
+ "sm_common: can't mark sector at %i as bad\n",
+ (int)ofs);
+ error = -EIO;
+ } else
+ mtd->ecc_stats.badblocks++;
+
+ nand_release_device(mtd);
+ return error;
+}
+
+int sm_register_device(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = (struct nand_chip *)mtd->priv;
+ int ret;
+
+ chip->options |= NAND_SKIP_BBTSCAN | NAND_SMARTMEDIA;
+
+ /* Scan for card properties */
+ ret = nand_scan_ident(mtd, 1);
+
+ if (ret)
+ return ret;
+
+ /* Set oob handling functions. */
+ if (mtd->writesize == SM_SECTOR_SIZE) {
+ chip->block_bad = sm_block_bad;
+ chip->block_markbad = sm_block_markbad;
+ chip->ecc.layout = &nand_oob_sm;
+
+ /* SmartMedia on small page nand, has page depedent oob layout,
+ thus let FTL do that hard job */
+ } else if (mtd->writesize != SM_SMALL_PAGE)
+ return -ENODEV;
+
+ ret = nand_scan_tail(mtd);
+ if (ret)
+ return ret;
+
+ ret = add_mtd_device(mtd);
+ if (ret)
+ return ret;
+ return 0;
+}
+EXPORT_SYMBOL_GPL(sm_register_device);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Maxim Levitsky <[email protected]>");
+MODULE_DESCRIPTION("Common SmartMedia/xD functions");
diff --git a/drivers/mtd/nand/sm_common.h b/drivers/mtd/nand/sm_common.h
new file mode 100644
index 0000000..a579fb6
--- /dev/null
+++ b/drivers/mtd/nand/sm_common.h
@@ -0,0 +1,61 @@
+/*
+ * Copyright (C) 2009 - Maxim Levitsky
+ * Common routines & support for SmartMedia/xD format
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/mtd/nand.h>
+
+/* Full oob structure as written on the flash */
+struct sm_oob {
+ u32 reserved;
+ u8 data_status;
+ u8 block_status;
+ u8 lba_copy1[2];
+ u8 ecc2[3];
+ u8 lba_copy2[2];
+ u8 ecc1[3];
+} __attribute__((packed));
+
+
+/* one sector is always 512 bytes, but it can consist of two nand pages */
+#define SM_SECTOR_SIZE 512
+
+/* oob area is also 16 bytes, but might be from two pages */
+#define SM_OOB_SIZE 16
+
+/* This is maximum zone size, and all devices that have more that one zone
+ have this size */
+#define SM_MAX_ZONE_SIZE 1024
+
+/* support for small page nand */
+#define SM_SMALL_PAGE 256
+#define SM_SMALL_OOB_SIZE 8
+
+
+extern int sm_register_device(struct mtd_info *mtd);
+
+
+inline int sm_sector_valid(struct sm_oob *oob)
+{
+ return hweight16(oob->data_status) >= 5;
+}
+
+inline int sm_block_valid(struct sm_oob *oob)
+{
+ return hweight16(oob->block_status) >= 7;
+}
+
+inline int sm_block_erased(struct sm_oob *oob)
+{
+ static const u32 erased_pattern[4] = {
+ 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF };
+
+ /* First test for erased block */
+ if (!memcmp(oob, erased_pattern, sizeof(*oob)))
+ return 1;
+ return 0;
+}
--
1.6.3.3
* Add an option NAND_SMARTMEDIA that can be set by nand driver
If set, it will cause separate ID table to be used, which includes
mask rom devices and new xD cards
* Workaround for wrong write protect status on some xD cards
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/nand/nand_base.c | 30 ++++++++++++++++++++++--------
drivers/mtd/nand/nand_ids.c | 39 +++++++++++++++++++++++++++++++++++++++
include/linux/mtd/nand.h | 11 +++++++++++
3 files changed, 72 insertions(+), 8 deletions(-)
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 3949d8c..093b868 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -397,9 +397,18 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
static int nand_check_wp(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
+ int wp;
+
+ /* broken xD cards report WP despite beeing writable */
+ if (chip->options & NAND_BROKEN_XD)
+ return 0;
+
/* Check the WP bit */
chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
- return (chip->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1;
+ wp = (chip->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1;
+
+
+ return wp;
}
/**
@@ -2622,14 +2631,18 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
}
/* Lookup the flash id */
- for (i = 0; nand_flash_ids[i].name != NULL; i++) {
- if (dev_id == nand_flash_ids[i].id) {
- type = &nand_flash_ids[i];
+#ifdef CONFIG_MTD_NAND_SMARTMEDIA
+ if (chip->options & NAND_SMARTMEDIA)
+ type = nand_smartmedia_flash_ids;
+ else
+#endif
+ type = nand_flash_ids;
+
+ for (i = 0; type->name != NULL; type++)
+ if (dev_id == type->id)
break;
- }
- }
- if (!type)
+ if (!type->name)
return ERR_PTR(-ENODEV);
if (!mtd->name)
@@ -2986,7 +2999,8 @@ int nand_scan_tail(struct mtd_info *mtd)
/* Fill in remaining MTD driver data */
mtd->type = MTD_NANDFLASH;
- mtd->flags = MTD_CAP_NANDFLASH;
+ mtd->flags = chip->options & NAND_ROM ? MTD_CAP_ROM :
+ MTD_CAP_NANDFLASH;
mtd->erase = nand_erase;
mtd->point = NULL;
mtd->unpoint = NULL;
diff --git a/drivers/mtd/nand/nand_ids.c b/drivers/mtd/nand/nand_ids.c
index 69ee2c9..f9e72d5 100644
--- a/drivers/mtd/nand/nand_ids.c
+++ b/drivers/mtd/nand/nand_ids.c
@@ -127,6 +127,45 @@ struct nand_flash_dev nand_flash_ids[] = {
{NULL,}
};
+#ifdef CONFIG_MTD_NAND_SMARTMEDIA
+struct nand_flash_dev nand_smartmedia_flash_ids[] = {
+
+ /* SmartMedia */
+ {"SmartMedia 1MiB 5V", 0x6e, 256, 1, 0x1000, 0},
+ {"SmartMedia 1MiB 3,3V", 0xe8, 256, 1, 0x1000, 0},
+ {"SmartMedia 1MiB 3,3V", 0xec, 256, 1, 0x1000, 0},
+ {"SmartMedia 2MiB 3,3V", 0xea, 256, 2, 0x1000, 0},
+ {"SmartMedia 2MiB 5V", 0x64, 256, 2, 0x1000, 0},
+ {"SmartMedia 2MiB 3,3V ROM", 0x5d, 512, 2, 0x2000, NAND_ROM},
+ {"SmartMedia 4MiB 3,3V", 0xe3, 512, 4, 0x2000, 0},
+ {"SmartMedia 4MiB 3,3/5V", 0xe5, 512, 4, 0x2000, 0},
+ {"SmartMedia 4MiB 5V", 0x6b, 512, 4, 0x2000, 0},
+ {"SmartMedia 4MiB 3,3V ROM", 0xd5, 512, 4, 0x2000, NAND_ROM},
+ {"SmartMedia 8MiB 3,3V", 0xe6, 512, 8, 0x2000, 0},
+ {"SmartMedia 8MiB 3,3V ROM", 0xd6, 512, 8, 0x2000, NAND_ROM},
+
+#define XD_TYPEM (NAND_NO_AUTOINCR | NAND_BROKEN_XD)
+ /* xD / SmartMedia */
+ {"SmartMedia/xD 16MiB 3,3V", 0x73, 512, 16, 0x4000, 0},
+ {"SmartMedia 16MiB 3,3V ROM", 0x57, 512, 16, 0x4000, NAND_ROM},
+ {"SmartMedia/xD 32MiB 3,3V", 0x75, 512, 32, 0x4000, 0},
+ {"SmartMedia 32MiB 3,3V ROM", 0x58, 512, 32, 0x4000, NAND_ROM},
+ {"SmartMedia/xD 64MiB 3,3V", 0x76, 512, 64, 0x4000, 0},
+ {"SmartMedia 64MiB 3,3V ROM", 0xd9, 512, 64, 0x4000, NAND_ROM},
+ {"SmartMedia/xD 128MiB 3,3V", 0x79, 512, 128, 0x4000, 0},
+ {"SmartMedia 128MiB 3,3V ROM", 0xda, 512, 128, 0x4000, NAND_ROM},
+ {"SmartMedia/xD 256MiB 3,3V", 0x71, 512, 256, 0x4000, XD_TYPEM},
+ {"SmartMedia 256MiB 3,3V ROM", 0x5b, 512, 256, 0x4000, NAND_ROM},
+
+ /* xD only */
+ {"xD 512MiB 3,3V", 0xDC, 512, 512, 0x4000, XD_TYPEM},
+ {"xD 1GiB 3,3V", 0xD3, 512, 1024, 0x4000, XD_TYPEM},
+ {"xD 2GiB 3,3V", 0xD5, 512, 2048, 0x4000, XD_TYPEM},
+ {NULL,}
+};
+EXPORT_SYMBOL(nand_smartmedia_flash_ids);
+#endif
+
/*
* Manufacturer ID list
*/
diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index 8c2333a..bb25cd8 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -170,6 +170,12 @@ typedef enum {
/* Chip does not allow subpage writes */
#define NAND_NO_SUBPAGE_WRITE 0x00000200
+/* Device is one of 'new' xD cards that expose fake nand command set */
+#define NAND_BROKEN_XD 0x00000400
+
+/* Device behaves just like nand, but is readonly */
+#define NAND_ROM 0x00000800
+
/* Options valid for Samsung large page devices */
#define NAND_SAMSUNG_LP_OPTIONS \
(NAND_NO_PADDING | NAND_CACHEPRG | NAND_COPYBACK)
@@ -195,9 +201,13 @@ typedef enum {
/* This option is defined if the board driver allocates its own buffers
(e.g. because it needs them DMA-coherent */
#define NAND_OWN_BUFFERS 0x00040000
+
/* Chip may not exist, so silence any errors in scan */
#define NAND_SCAN_SILENT_NODEV 0x00080000
+/* controller supports only xD/SmartMedia cards*/
+#define NAND_SMARTMEDIA 0x00100000
+
/* Options set by nand scan */
/* Nand scan has allocated controller struct */
#define NAND_CONTROLLER_ALLOC 0x80000000
@@ -458,6 +468,7 @@ struct nand_manufacturers {
};
extern struct nand_flash_dev nand_flash_ids[];
+extern struct nand_flash_dev nand_smartmedia_flash_ids[];
extern struct nand_manufacturers nand_manuf_ids[];
extern int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd);
--
1.6.3.3
Although nand_do_write_ops intends to allow such mode, it fails do do so
Probably this was never tested
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/nand/nand_base.c | 16 +++++++++-------
1 files changed, 9 insertions(+), 7 deletions(-)
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 8ff36be..29e986e 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -1879,11 +1879,9 @@ static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip,
* @oob: oob data buffer
* @ops: oob ops structure
*/
-static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob,
- struct mtd_oob_ops *ops)
+static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob, size_t len,
+ struct mtd_oob_ops *ops)
{
- size_t len = ops->ooblen;
-
switch(ops->mode) {
case MTD_OOB_PLACE:
@@ -1938,6 +1936,7 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
int chipnr, realpage, page, blockmask, column;
struct nand_chip *chip = mtd->priv;
uint32_t writelen = ops->len;
+ uint32_t oobwritelen = ops->ooblen;
uint8_t *oob = ops->oobbuf;
uint8_t *buf = ops->datbuf;
int ret, subpage;
@@ -1994,8 +1993,11 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
wbuf = chip->buffers->databuf;
}
- if (unlikely(oob))
- oob = nand_fill_oob(chip, oob, ops);
+ if (unlikely(oob)) {
+ size_t len = min(oobwritelen, mtd->oobsize);
+ oob = nand_fill_oob(chip, oob, len, ops);
+ oobwritelen -= len;
+ }
ret = chip->write_page(mtd, chip, wbuf, page, cached,
(ops->mode == MTD_OOB_RAW));
@@ -2169,7 +2171,7 @@ static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
chip->pagebuf = -1;
memset(chip->oob_poi, 0xff, mtd->oobsize);
- nand_fill_oob(chip, ops->oobbuf, ops);
+ nand_fill_oob(chip, ops->oobbuf, ops->ooblen, ops);
status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask);
memset(chip->oob_poi, 0xff, mtd->oobsize);
--
1.6.3.3
This exports:
nand_do_read_oob
nand_do_write_oob
nand_get_device
nand_put_device
This functions will be used to implement custom oob based
bad block handling in upcoming smartmedia common module
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/nand/nand_base.c | 18 +++++++++---------
include/linux/mtd/nand.h | 12 ++++++++++++
2 files changed, 21 insertions(+), 9 deletions(-)
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 961c98f..3949d8c 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -96,11 +96,6 @@ static struct nand_ecclayout nand_oob_128 = {
.length = 78}}
};
-static int nand_get_device(struct nand_chip *chip, struct mtd_info *mtd,
- int new_state);
-
-static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
- struct mtd_oob_ops *ops);
/*
* For devices which display every fart in the system on a separate LED. Is
@@ -114,7 +109,7 @@ DEFINE_LED_TRIGGER(nand_led_trigger);
*
* Deselect, release chip lock and wake up anyone waiting on the device
*/
-static void nand_release_device(struct mtd_info *mtd)
+void nand_release_device(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
@@ -128,6 +123,7 @@ static void nand_release_device(struct mtd_info *mtd)
wake_up(&chip->controller->wq);
spin_unlock(&chip->controller->lock);
}
+EXPORT_SYMBOL_GPL(nand_release_device);
/**
* nand_read_byte - [DEFAULT] read one byte from the chip
@@ -721,7 +717,7 @@ static void panic_nand_get_device(struct nand_chip *chip,
*
* Get the device and lock it for exclusive access
*/
-static int
+int
nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state)
{
spinlock_t *lock = &chip->controller->lock;
@@ -753,6 +749,7 @@ nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state)
remove_wait_queue(wq, &wait);
goto retry;
}
+EXPORT_SYMBOL_GPL(nand_get_device);
/**
* panic_nand_wait - [GENERIC] wait until the command is done
@@ -1532,7 +1529,7 @@ static int nand_write_oob_syndrome(struct mtd_info *mtd,
*
* NAND read out-of-band data from the spare area
*/
-static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
+int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
struct mtd_oob_ops *ops)
{
int page, realpage, chipnr, sndcmd = 1;
@@ -1616,6 +1613,7 @@ static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
ops->oobretlen = ops->ooblen;
return 0;
}
+EXPORT_SYMBOL_GPL(nand_do_read_oob);
/**
* nand_read_oob - [MTD Interface] NAND read data and/or out-of-band
@@ -2108,7 +2106,7 @@ static int nand_write(struct mtd_info *mtd, loff_t to, size_t len,
*
* NAND write out-of-band
*/
-static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
+int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
struct mtd_oob_ops *ops)
{
int chipnr, page, status, len;
@@ -2179,6 +2177,7 @@ static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
return 0;
}
+EXPORT_SYMBOL_GPL(nand_do_write_oob);
/**
* nand_write_oob - [MTD Interface] NAND write data and/or out-of-band
@@ -3080,6 +3079,7 @@ EXPORT_SYMBOL_GPL(nand_scan_ident);
EXPORT_SYMBOL_GPL(nand_scan_tail);
EXPORT_SYMBOL_GPL(nand_release);
+
static int __init nand_base_init(void)
{
led_trigger_register_simple("nand-disk", &nand_led_trigger);
diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index ccab9df..8c2333a 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -469,6 +469,18 @@ extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len,
size_t * retlen, uint8_t * buf);
+extern int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
+ struct mtd_oob_ops *ops);
+
+extern int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
+ struct mtd_oob_ops *ops);
+
+extern int nand_get_device(struct nand_chip *chip,
+ struct mtd_info *mtd, int new_state);
+
+extern void nand_release_device(struct mtd_info *mtd);
+
+
/**
* struct platform_nand_chip - chip level device structure
* @nr_chips: max. number of chips to scan for
--
1.6.3.3
This changes the behavier of MTD_OOB_RAW. It used to read both OOB and data
to the data buffer, however you would still need to specify the dummy oob buffer.
This is only used in one place, but makes it hard to read data+oob without ECC
test, thus I removed that behavier, and fixed the user.
Now MTD_OOB_RAW behaves like MTD_OOB_PLACE, but doesn't do ECC validation
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/nand/nand_base.c | 5 -----
drivers/mtd/nand/nand_bbt.c | 26 ++++++++++++++++++++++----
include/linux/mtd/mtd.h | 4 +---
3 files changed, 23 insertions(+), 12 deletions(-)
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 405c538..8ff36be 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -1286,8 +1286,6 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
if (unlikely(oob)) {
- /* Raw mode does data:oob:data:oob */
- if (ops->mode != MTD_OOB_RAW) {
int toread = min(oobreadlen,
max_oobsize);
if (toread) {
@@ -1295,9 +1293,6 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
oob, ops, toread);
oobreadlen -= toread;
}
- } else
- buf = nand_transfer_oob(chip,
- buf, ops, mtd->oobsize);
}
if (!(chip->options & NAND_NO_READRDY)) {
diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/nand_bbt.c
index 55c23e5..387c45c 100644
--- a/drivers/mtd/nand/nand_bbt.c
+++ b/drivers/mtd/nand/nand_bbt.c
@@ -237,15 +237,33 @@ static int scan_read_raw(struct mtd_info *mtd, uint8_t *buf, loff_t offs,
size_t len)
{
struct mtd_oob_ops ops;
+ int res;
ops.mode = MTD_OOB_RAW;
ops.ooboffs = 0;
ops.ooblen = mtd->oobsize;
- ops.oobbuf = buf;
- ops.datbuf = buf;
- ops.len = len;
- return mtd->read_oob(mtd, offs, &ops);
+
+ while (len > 0) {
+ if (len <= mtd->writesize) {
+ ops.oobbuf = buf + len;
+ ops.datbuf = buf;
+ ops.len = len;
+ return mtd->read_oob(mtd, offs, &ops);
+ } else {
+ ops.oobbuf = buf + mtd->writesize;
+ ops.datbuf = buf;
+ ops.len = mtd->writesize;
+ res = mtd->read_oob(mtd, offs, &ops);
+
+ if (res)
+ return res;
+ }
+
+ buf += mtd->oobsize + mtd->writesize;
+ len -= mtd->writesize;
+ }
+ return 0;
}
/*
diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h
index 662d747..84bb375 100644
--- a/include/linux/mtd/mtd.h
+++ b/include/linux/mtd/mtd.h
@@ -61,9 +61,7 @@ struct mtd_erase_region_info {
* MTD_OOB_PLACE: oob data are placed at the given offset
* MTD_OOB_AUTO: oob data are automatically placed at the free areas
* which are defined by the ecclayout
- * MTD_OOB_RAW: mode to read raw data+oob in one chunk. The oob data
- * is inserted into the data. Thats a raw image of the
- * flash contents.
+ * MTD_OOB_RAW: mode to read oob and data without doing ECC checking
*/
typedef enum {
MTD_OOB_PLACE,
--
1.6.3.3
This patch add ability to export sysfs attributes below
block disk device.
This can be used to pass UDEV information about the FTL
and could include vendor, serial, version, etc...
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/mtd_blkdevs.c | 11 ++++++++++-
include/linux/mtd/blktrans.h | 2 ++
2 files changed, 12 insertions(+), 1 deletions(-)
diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c
index a65eb07..1c4e615 100644
--- a/drivers/mtd/mtd_blkdevs.c
+++ b/drivers/mtd/mtd_blkdevs.c
@@ -317,7 +317,6 @@ int add_mtd_blktrans_dev(struct mtd_blktrans_dev *new)
set_capacity(gd, (new->size * tr->blksize) >> 9);
-
/* Create the request queue */
spin_lock_init(&new->queue_lock);
new->rq = blk_init_queue(mtd_blktrans_request, &new->queue_lock);
@@ -350,6 +349,11 @@ int add_mtd_blktrans_dev(struct mtd_blktrans_dev *new)
new->open = 0;
add_disk(gd);
+ if (new->disk_attributes)
+ sysfs_create_group(&disk_to_dev(gd)->kobj,
+ new->disk_attributes);
+
+
return 0;
error4:
blk_cleanup_queue(new->rq);
@@ -376,6 +380,11 @@ int del_mtd_blktrans_dev(struct mtd_blktrans_dev *old)
/* stop new requests to arrive */
del_gendisk(old->disk);
+
+ if (old->disk_attributes)
+ sysfs_remove_group(&disk_to_dev(old->disk)->kobj,
+ old->disk_attributes);
+
/* flush current requests */
spin_lock_irqsave(&old->queue_lock, flags);
old->deleted = 1;
diff --git a/include/linux/mtd/blktrans.h b/include/linux/mtd/blktrans.h
index e276aca..faf1e54 100644
--- a/include/linux/mtd/blktrans.h
+++ b/include/linux/mtd/blktrans.h
@@ -9,6 +9,7 @@
#define __MTD_TRANS_H__
#include <linux/mutex.h>
+#include <linux/sysfs.h>
struct hd_geometry;
struct mtd_info;
@@ -27,6 +28,7 @@ struct mtd_blktrans_dev {
int deleted;
int open;
struct gendisk *disk;
+ struct attribute_group *disk_attributes;
struct task_struct *thread;
struct request_queue *rq;
spinlock_t queue_lock;
--
1.6.3.3
Since all userspace threads are frozen at the time the nand_suspend is called,
they aren't inside any nand function.
We don't call try_to_freeze in nand ether. Thus the only user that can be insize
the nand functions is an non freezeable kernel thread.
Thus we can safely wait for it to finish.
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/nand/nand_base.c | 3 ---
1 files changed, 0 insertions(+), 3 deletions(-)
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 29e986e..961c98f 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -744,9 +744,6 @@ nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state)
chip->state = FL_PM_SUSPENDED;
spin_unlock(lock);
return 0;
- } else {
- spin_unlock(lock);
- return -EAGAIN;
}
}
set_current_state(TASK_UNINTERRUPTIBLE);
--
1.6.3.3
These functions can be used as long as we don't need access to global mtd table, but have
a pointer to the mtd device.
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/mtdcore.c | 60 ++++++++++++++++++++++++++++++----------------
include/linux/mtd/mtd.h | 3 +-
2 files changed, 41 insertions(+), 22 deletions(-)
diff --git a/drivers/mtd/mtdcore.c b/drivers/mtd/mtdcore.c
index c356c0a..3bdb7e8 100644
--- a/drivers/mtd/mtdcore.c
+++ b/drivers/mtd/mtdcore.c
@@ -453,27 +453,38 @@ struct mtd_info *get_mtd_device(struct mtd_info *mtd, int num)
ret = NULL;
}
- if (!ret)
- goto out_unlock;
-
- if (!try_module_get(ret->owner))
- goto out_unlock;
-
- if (ret->get_device) {
- err = ret->get_device(ret);
- if (err)
- goto out_put;
+ if (!ret) {
+ ret = ERR_PTR(err);
+ goto out;
}
- ret->usecount++;
+ err = __get_mtd_device(ret);
+ if (err)
+ ret = ERR_PTR(err);
+out:
mutex_unlock(&mtd_table_mutex);
return ret;
+}
-out_put:
- module_put(ret->owner);
-out_unlock:
- mutex_unlock(&mtd_table_mutex);
- return ERR_PTR(err);
+
+int __get_mtd_device(struct mtd_info *mtd)
+{
+ int err;
+
+ if (!try_module_get(mtd->owner))
+ return -ENODEV;
+
+ if (mtd->get_device) {
+
+ err = mtd->get_device(mtd);
+
+ if (err) {
+ module_put(mtd->owner);
+ return err;
+ }
+ }
+ mtd->usecount++;
+ return 0;
}
/**
@@ -524,14 +535,19 @@ out_unlock:
void put_mtd_device(struct mtd_info *mtd)
{
- int c;
-
mutex_lock(&mtd_table_mutex);
- c = --mtd->usecount;
+ __put_mtd_device(mtd);
+ mutex_unlock(&mtd_table_mutex);
+
+}
+
+void __put_mtd_device(struct mtd_info *mtd)
+{
+ --mtd->usecount;
+ BUG_ON(mtd->usecount < 0);
+
if (mtd->put_device)
mtd->put_device(mtd);
- mutex_unlock(&mtd_table_mutex);
- BUG_ON(c < 0);
module_put(mtd->owner);
}
@@ -569,7 +585,9 @@ EXPORT_SYMBOL_GPL(add_mtd_device);
EXPORT_SYMBOL_GPL(del_mtd_device);
EXPORT_SYMBOL_GPL(get_mtd_device);
EXPORT_SYMBOL_GPL(get_mtd_device_nm);
+EXPORT_SYMBOL_GPL(__get_mtd_device);
EXPORT_SYMBOL_GPL(put_mtd_device);
+EXPORT_SYMBOL_GPL(__put_mtd_device);
EXPORT_SYMBOL_GPL(register_mtd_user);
EXPORT_SYMBOL_GPL(unregister_mtd_user);
EXPORT_SYMBOL_GPL(default_mtd_writev);
diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h
index 0f32a9b..662d747 100644
--- a/include/linux/mtd/mtd.h
+++ b/include/linux/mtd/mtd.h
@@ -290,8 +290,9 @@ extern int add_mtd_device(struct mtd_info *mtd);
extern int del_mtd_device (struct mtd_info *mtd);
extern struct mtd_info *get_mtd_device(struct mtd_info *mtd, int num);
+extern int __get_mtd_device(struct mtd_info *mtd);
+extern void __put_mtd_device(struct mtd_info *mtd);
extern struct mtd_info *get_mtd_device_nm(const char *name);
-
extern void put_mtd_device(struct mtd_info *mtd);
--
1.6.3.3
First, use lockless versions of get/put_mtd_device
We don't care what happened to mtd table, because we have a pointer
to mtd device. It guaranteed to exist till we do final put_mtd_device
Also add locking to prevent all kinds or races
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/mtd_blkdevs.c | 82 ++++++++++++++++++++++++++++----------------
1 files changed, 52 insertions(+), 30 deletions(-)
diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c
index 9e118cf..841c6ae 100644
--- a/drivers/mtd/mtd_blkdevs.c
+++ b/drivers/mtd/mtd_blkdevs.c
@@ -123,33 +123,33 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode)
{
struct mtd_blktrans_dev *dev = bdev->bd_disk->private_data;
struct mtd_blktrans_ops *tr = dev->tr;
- int ret = -ENODEV;
-
- if (!get_mtd_device(NULL, dev->mtd->index))
- goto out;
+ int ret = 0;
+ mutex_lock(&dev->lock);
if (dev->open++)
goto out;
if (dev->deleted)
goto out;
+ ret = -ENODEV;
if (!try_module_get(tr->owner))
- goto out_tr;
+ goto out;
- /* FIXME: Locking. A hot pluggable device can go away
- (del_mtd_device can be called for it) without its module
- being unloaded. */
- dev->mtd->usecount++;
+ if (__get_mtd_device(dev->mtd)) {
+ module_put(tr->owner);
+ goto out;
+ }
ret = 0;
if (tr->open && (ret = tr->open(dev))) {
- dev->mtd->usecount--;
- put_mtd_device(dev->mtd);
- out_tr:
module_put(tr->owner);
+ __put_mtd_device(dev->mtd);
+ goto out;
+
}
out:
+ mutex_unlock(&dev->lock);
return ret;
}
@@ -159,18 +159,11 @@ static int blktrans_release(struct gendisk *disk, fmode_t mode)
struct mtd_blktrans_ops *tr = dev->tr;
int ret = 0;
+ mutex_lock(&dev->lock);
dev->open--;
if (dev->open)
return 0;
- if (tr->release)
- ret = tr->release(dev);
-
- if (!ret) {
- dev->mtd->usecount--;
- put_mtd_device(dev->mtd);
- module_put(tr->owner);
- }
/* Free the private data */
if (dev->deleted) {
@@ -180,33 +173,59 @@ static int blktrans_release(struct gendisk *disk, fmode_t mode)
return 0;
}
+ ret = tr->release ? tr->release(dev) : 0;
+ module_put(tr->owner);
+
+ if (dev->mtd)
+ __put_mtd_device(dev->mtd);
+
+ mutex_unlock(&dev->lock);
return ret;
}
static int blktrans_getgeo(struct block_device *bdev, struct hd_geometry *geo)
{
struct mtd_blktrans_dev *dev = bdev->bd_disk->private_data;
+ int error;
+
+ mutex_lock(&dev->lock);
+ error = -ENODEV;
+ if (dev->deleted)
+ goto out;
+
+ error = -ENOTTY;
if (dev->tr->getgeo)
- return dev->tr->getgeo(dev, geo);
- return -ENOTTY;
+ error = dev->tr->getgeo(dev, geo);
+out:
+ mutex_unlock(&dev->lock);
+ return error;
}
static int blktrans_ioctl(struct block_device *bdev, fmode_t mode,
unsigned int cmd, unsigned long arg)
{
struct mtd_blktrans_dev *dev = bdev->bd_disk->private_data;
- struct mtd_blktrans_ops *tr = dev->tr;
+ int error = -ENODEV;
+
+ mutex_lock(&dev->lock);
+
+ if (dev->deleted)
+ goto out;
+
+ error = -ENOTTY;
switch (cmd) {
case BLKFLSBUF:
- if (tr->flush)
- return tr->flush(dev);
- /* The core code did the work, we had nothing to do. */
- return 0;
+ if (dev->tr->flush)
+ error = dev->tr->flush(dev);
+ break;
default:
- return -ENOTTY;
+ break;
}
+out:
+ mutex_unlock(&dev->lock);
+ return error;
}
static const struct block_device_operations mtd_blktrans_ops = {
@@ -354,16 +373,19 @@ int del_mtd_blktrans_dev(struct mtd_blktrans_dev *old)
/* Stop the thread */
kthread_stop(old->thread);
+ /* Tell trans driver to release the device */
+ mutex_lock(&old->lock);
+
if (old->open) {
if (old->tr->release)
old->tr->release(old);
- put_mtd_device(old->mtd);
+ __put_mtd_device(old->mtd);
}
/* From now on, no calls into trans can be made */
/* Mtd device will be gone real soon now */
old->mtd = NULL;
-
+ mutex_unlock(&old->lock);
blk_cleanup_queue(old->rq);
return 0;
}
--
1.6.3.3
We need that structure till last user exits, and that might be years after
mtd device disappered.
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/ftl.c | 1 -
drivers/mtd/inftlcore.c | 1 -
drivers/mtd/mtd_blkdevs.c | 13 +++++++++++++
drivers/mtd/mtdblock.c | 1 -
drivers/mtd/mtdblock_ro.c | 1 -
drivers/mtd/nftlcore.c | 1 -
drivers/mtd/rfd_ftl.c | 1 -
drivers/mtd/ssfdc.c | 1 -
include/linux/mtd/blktrans.h | 1 +
9 files changed, 14 insertions(+), 7 deletions(-)
diff --git a/drivers/mtd/ftl.c b/drivers/mtd/ftl.c
index e56d6b4..62da9eb 100644
--- a/drivers/mtd/ftl.c
+++ b/drivers/mtd/ftl.c
@@ -1082,7 +1082,6 @@ static void ftl_remove_dev(struct mtd_blktrans_dev *dev)
{
del_mtd_blktrans_dev(dev);
ftl_freepart((partition_t *)dev);
- kfree(dev);
}
static struct mtd_blktrans_ops ftl_tr = {
diff --git a/drivers/mtd/inftlcore.c b/drivers/mtd/inftlcore.c
index 8aca552..015a7fe 100755
--- a/drivers/mtd/inftlcore.c
+++ b/drivers/mtd/inftlcore.c
@@ -139,7 +139,6 @@ static void inftl_remove_dev(struct mtd_blktrans_dev *dev)
kfree(inftl->PUtable);
kfree(inftl->VUtable);
- kfree(inftl);
}
/*
diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c
index 966398b..9e118cf 100644
--- a/drivers/mtd/mtd_blkdevs.c
+++ b/drivers/mtd/mtd_blkdevs.c
@@ -131,6 +131,9 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode)
if (dev->open++)
goto out;
+ if (dev->deleted)
+ goto out;
+
if (!try_module_get(tr->owner))
goto out_tr;
@@ -169,6 +172,14 @@ static int blktrans_release(struct gendisk *disk, fmode_t mode)
module_put(tr->owner);
}
+ /* Free the private data */
+ if (dev->deleted) {
+ module_put(tr->owner);
+ mutex_unlock(&dev->lock);
+ kfree(dev);
+ return 0;
+ }
+
return ret;
}
@@ -338,6 +349,8 @@ int del_mtd_blktrans_dev(struct mtd_blktrans_dev *old)
/* stop new requests to arrive */
del_gendisk(old->disk);
+ old->deleted = 1;
+
/* Stop the thread */
kthread_stop(old->thread);
diff --git a/drivers/mtd/mtdblock.c b/drivers/mtd/mtdblock.c
index 9f41b1a..d8322cc 100644
--- a/drivers/mtd/mtdblock.c
+++ b/drivers/mtd/mtdblock.c
@@ -368,7 +368,6 @@ static void mtdblock_add_mtd(struct mtd_blktrans_ops *tr, struct mtd_info *mtd)
static void mtdblock_remove_dev(struct mtd_blktrans_dev *dev)
{
del_mtd_blktrans_dev(dev);
- kfree(dev);
}
static struct mtd_blktrans_ops mtdblock_tr = {
diff --git a/drivers/mtd/mtdblock_ro.c b/drivers/mtd/mtdblock_ro.c
index 852165f..54ff288 100644
--- a/drivers/mtd/mtdblock_ro.c
+++ b/drivers/mtd/mtdblock_ro.c
@@ -49,7 +49,6 @@ static void mtdblock_add_mtd(struct mtd_blktrans_ops *tr, struct mtd_info *mtd)
static void mtdblock_remove_dev(struct mtd_blktrans_dev *dev)
{
del_mtd_blktrans_dev(dev);
- kfree(dev);
}
static struct mtd_blktrans_ops mtdblock_tr = {
diff --git a/drivers/mtd/nftlcore.c b/drivers/mtd/nftlcore.c
index 1002e18..a4578bf 100644
--- a/drivers/mtd/nftlcore.c
+++ b/drivers/mtd/nftlcore.c
@@ -126,7 +126,6 @@ static void nftl_remove_dev(struct mtd_blktrans_dev *dev)
del_mtd_blktrans_dev(dev);
kfree(nftl->ReplUnitTable);
kfree(nftl->EUNtable);
- kfree(nftl);
}
/*
diff --git a/drivers/mtd/rfd_ftl.c b/drivers/mtd/rfd_ftl.c
index d2aa9c4..63b83c0 100644
--- a/drivers/mtd/rfd_ftl.c
+++ b/drivers/mtd/rfd_ftl.c
@@ -817,7 +817,6 @@ static void rfd_ftl_remove_dev(struct mtd_blktrans_dev *dev)
vfree(part->sector_map);
kfree(part->header_cache);
kfree(part->blocks);
- kfree(part);
}
static struct mtd_blktrans_ops rfd_ftl_tr = {
diff --git a/drivers/mtd/ssfdc.c b/drivers/mtd/ssfdc.c
index 3f67e00..81c4ecd 100644
--- a/drivers/mtd/ssfdc.c
+++ b/drivers/mtd/ssfdc.c
@@ -375,7 +375,6 @@ static void ssfdcr_remove_dev(struct mtd_blktrans_dev *dev)
del_mtd_blktrans_dev(dev);
kfree(ssfdc->logic_block_map);
- kfree(ssfdc);
}
static int ssfdcr_readsect(struct mtd_blktrans_dev *dev,
diff --git a/include/linux/mtd/blktrans.h b/include/linux/mtd/blktrans.h
index 507f7b2..e276aca 100644
--- a/include/linux/mtd/blktrans.h
+++ b/include/linux/mtd/blktrans.h
@@ -24,6 +24,7 @@ struct mtd_blktrans_dev {
int devnum;
unsigned long size;
int readonly;
+ int deleted;
int open;
struct gendisk *disk;
struct task_struct *thread;
--
1.6.3.3
This patch adds tracking for open and close calls.
Now trans ->open and ->release are never called twise in a row
->release is also called once before mtd device disappers
Proper locking will be added in follow up patch
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/mtd_blkdevs.c | 18 ++++++++++++++++++
include/linux/mtd/blktrans.h | 1 +
2 files changed, 19 insertions(+), 0 deletions(-)
diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c
index 93c87af..966398b 100644
--- a/drivers/mtd/mtd_blkdevs.c
+++ b/drivers/mtd/mtd_blkdevs.c
@@ -128,6 +128,9 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode)
if (!get_mtd_device(NULL, dev->mtd->index))
goto out;
+ if (dev->open++)
+ goto out;
+
if (!try_module_get(tr->owner))
goto out_tr;
@@ -153,6 +156,10 @@ static int blktrans_release(struct gendisk *disk, fmode_t mode)
struct mtd_blktrans_ops *tr = dev->tr;
int ret = 0;
+ dev->open--;
+ if (dev->open)
+ return 0;
+
if (tr->release)
ret = tr->release(dev);
@@ -304,6 +311,7 @@ int add_mtd_blktrans_dev(struct mtd_blktrans_dev *new)
if (new->readonly)
set_disk_ro(gd, 1);
+ new->open = 0;
add_disk(gd);
return 0;
@@ -333,6 +341,16 @@ int del_mtd_blktrans_dev(struct mtd_blktrans_dev *old)
/* Stop the thread */
kthread_stop(old->thread);
+ if (old->open) {
+ if (old->tr->release)
+ old->tr->release(old);
+ put_mtd_device(old->mtd);
+ }
+
+ /* From now on, no calls into trans can be made */
+ /* Mtd device will be gone real soon now */
+ old->mtd = NULL;
+
blk_cleanup_queue(old->rq);
return 0;
}
diff --git a/include/linux/mtd/blktrans.h b/include/linux/mtd/blktrans.h
index a4b3928..507f7b2 100644
--- a/include/linux/mtd/blktrans.h
+++ b/include/linux/mtd/blktrans.h
@@ -24,6 +24,7 @@ struct mtd_blktrans_dev {
int devnum;
unsigned long size;
int readonly;
+ int open;
struct gendisk *disk;
struct task_struct *thread;
struct request_queue *rq;
--
1.6.3.3
Drat... forgot to compile....
This is an updated version
(This time compile and run tested with xd card)
---
This implements new readwrite SmartMedia/xd FTL.
mtd driver must have support proper ECC and badblock vertification
based on oob parts for 512 bytes nand.
Also mtd driver must define read_oob and write_oob, which are used
to read and write both data and oob together.
Signed-off-by: Maxim Levitsky <[email protected]>
---
drivers/mtd/Kconfig | 21 +
drivers/mtd/Makefile | 1 +
drivers/mtd/sm_ftl.c | 1258 ++++++++++++++++++++++++++++++++++++++++++++++++++
drivers/mtd/sm_ftl.h | 92 ++++
4 files changed, 1372 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/sm_ftl.c
create mode 100644 drivers/mtd/sm_ftl.h
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index ecf90f5..0105ae0 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -304,6 +304,27 @@ config SSFDC
This enables read only access to SmartMedia formatted NAND
flash. You can mount it with FAT file system.
+
+config SM_FTL
+ tristate "SmartMedia/xD new translation layer"
+ depends on EXPERIMENTAL && BLOCK
+ select MTD_BLKDEVS
+ help
+ This enables new and very EXPERMENTAL support for SmartMedia/xD
+ FTL (Flash tanslation layer)
+ Write support isn't yet well tested, therefore this code IS likely to
+ eat your card, so please don't use it together with valuable data.
+ Use readonly driver (CONFIG_SSFDC) instead.
+
+config SM_FTL_MUSEUM
+ boolean "Additional Support for 1MB and 2MB SmartMedia cards"
+ depends on SM_FTL && MTD_NAND
+ select MTD_NAND_ECC_SMC
+ help
+ Very old SmartMedia cards need ECC to be caluculated in the FTL
+ Such cards are very rare, thus enabling this option is mostly useless
+ Also this support is completely UNTESTED.
+
config MTD_OOPS
tristate "Log panic/oops to an MTD buffer"
depends on MTD
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 82d1e4d..d53357b 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_NFTL) += nftl.o
obj-$(CONFIG_INFTL) += inftl.o
obj-$(CONFIG_RFD_FTL) += rfd_ftl.o
obj-$(CONFIG_SSFDC) += ssfdc.o
+obj-$(CONFIG_SM_FTL) += sm_ftl.o
obj-$(CONFIG_MTD_OOPS) += mtdoops.o
nftl-objs := nftlcore.o nftlmount.o
diff --git a/drivers/mtd/sm_ftl.c b/drivers/mtd/sm_ftl.c
new file mode 100644
index 0000000..87cc604
--- /dev/null
+++ b/drivers/mtd/sm_ftl.c
@@ -0,0 +1,1258 @@
+/*
+ * Copyright (C) 2009 - Maxim Levitsky
+ * SmartMedia/xD translation layer
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/random.h>
+#include <linux/hdreg.h>
+#include <linux/kthread.h>
+#include <linux/freezer.h>
+#include <linux/sysfs.h>
+#include <linux/bitops.h>
+#include "nand/sm_common.h"
+#include "sm_ftl.h"
+
+#ifdef CONFIG_SM_FTL_MUSEUM
+#include <linux/mtd/nand_ecc.h>
+#endif
+
+
+struct workqueue_struct *cache_flush_workqueue;
+
+static int cache_timeout = 1000;
+module_param(cache_timeout, bool, S_IRUGO);
+MODULE_PARM_DESC(cache_timeout, "Timeout in ms for cache flush (1000 default");
+
+/* ------------------- sysfs attributtes ---------------------------------- */
+struct sm_sysfs_attribute {
+ struct device_attribute dev_attr;
+ char *data;
+ int len;
+};
+
+ssize_t sm_attr_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct sm_sysfs_attribute *sm_attr =
+ container_of(attr, struct sm_sysfs_attribute, dev_attr);
+
+ strncpy(buf, sm_attr->data, sm_attr->len);
+ return sm_attr->len;
+}
+
+
+#define NUM_ATTRIBUTES 1
+#define SM_CIS_VENDOR_OFFSET 0x59
+struct attribute_group *sm_create_sysfs_attributes(struct sm_ftl *ftl)
+{
+ struct attribute_group *attr_group;
+ struct attribute **attributes;
+ struct sm_sysfs_attribute *vendor_attribute;
+
+ int vendor_len = strnlen(ftl->cis_buffer + SM_CIS_VENDOR_OFFSET,
+ SM_SMALL_PAGE - SM_CIS_VENDOR_OFFSET);
+
+ char *vendor = kmalloc(vendor_len, GFP_KERNEL);
+ memcpy(vendor, ftl->cis_buffer + SM_CIS_VENDOR_OFFSET, vendor_len);
+ vendor[vendor_len] = 0;
+
+ /* Initialize sysfs attributes */
+ vendor_attribute =
+ kzalloc(sizeof(struct sm_sysfs_attribute), GFP_KERNEL);
+
+ vendor_attribute->data = vendor;
+ vendor_attribute->len = vendor_len;
+ vendor_attribute->dev_attr.attr.name = "vendor";
+ vendor_attribute->dev_attr.attr.mode = S_IRUGO;
+ vendor_attribute->dev_attr.show = sm_attr_show;
+
+
+ /* Create array of pointers to the attributes */
+ attributes = kzalloc(sizeof(struct attribute *) * (NUM_ATTRIBUTES + 1),
+ GFP_KERNEL);
+ attributes[0] = &vendor_attribute->dev_attr.attr;
+
+ /* Finally create the attribute group */
+ attr_group = kzalloc(sizeof(struct attribute_group), GFP_KERNEL);
+ attr_group->attrs = attributes;
+ return attr_group;
+}
+
+void sm_delete_sysfs_attributes(struct sm_ftl *ftl)
+{
+ struct attribute **attributes = ftl->trans->disk_attributes->attrs;
+ int i;
+
+ for (i = 0; attributes[i] ; i++) {
+
+ struct device_attribute *dev_attr = container_of(attributes[i],
+ struct device_attribute, attr);
+
+ struct sm_sysfs_attribute *sm_attr =
+ container_of(dev_attr,
+ struct sm_sysfs_attribute, dev_attr);
+
+ kfree(sm_attr->data);
+ kfree(sm_attr);
+ }
+
+ kfree(ftl->trans->disk_attributes->attrs);
+ kfree(ftl->trans->disk_attributes);
+}
+
+
+/* ----------------------- oob helpers -------------------------------------- */
+
+static int sm_get_lba(u8 *lba)
+{
+ /* check fixed bits */
+ if ((lba[0] & 0xF8) != 0x10)
+ return -2;
+
+ /* check parity - endianess doesn't matter */
+ if (hweight16(*(u16 *)lba) & 1)
+ return -2;
+
+ return (lba[1] >> 1) | ((lba[0] & 0x07) << 7);
+}
+
+
+/*
+ * Read LBA asscociated with block
+ * returns -1, if block is erased
+ * returns -2 if error happens
+ */
+static int sm_read_lba(struct sm_oob *oob)
+{
+ static const u32 erased_pattern[4] = {
+ 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF };
+
+ u16 lba_test;
+ int lba;
+
+ /* First test for erased block */
+ if (!memcmp(oob, erased_pattern, SM_OOB_SIZE))
+ return -1;
+
+ /* Now check is both copies of the LBA differ too much */
+ lba_test = *(u16 *)oob->lba_copy1 ^ *(u16*)oob->lba_copy2;
+ if (lba_test && !is_power_of_2(lba_test))
+ return -2;
+
+ /* And read it */
+ lba = sm_get_lba(oob->lba_copy1);
+
+ if (lba == -2)
+ lba = sm_get_lba(oob->lba_copy2);
+
+ return lba;
+}
+
+static void sm_write_lba(struct sm_oob *oob, u16 lba)
+{
+ u8 tmp[2];
+
+ WARN_ON(lba >= 1000);
+
+ tmp[0] = 0x10 | ((lba >> 7) & 0x07);
+ tmp[1] = (lba << 1) & 0xFF;
+
+ if (hweight16(*(u16 *)tmp) & 0x01)
+ tmp[1] |= 1;
+
+ oob->lba_copy1[0] = oob->lba_copy2[0] = tmp[0];
+ oob->lba_copy1[1] = oob->lba_copy2[1] = tmp[1];
+}
+
+
+/* Make offset from parts */
+static loff_t sm_mkoffset(struct sm_ftl *ftl, int zone, int block, int boffset)
+{
+ WARN_ON(boffset & (SM_SECTOR_SIZE - 1));
+ WARN_ON(zone < 0 || zone >= ftl->zone_count);
+ WARN_ON(block >= ftl->zone_size);
+ WARN_ON(boffset >= ftl->block_size);
+
+ if (block == -1)
+ return -1;
+
+ return (zone * SM_MAX_ZONE_SIZE + block) * ftl->block_size + boffset;
+}
+
+/* Breaks offset into parts */
+static void sm_break_offset(struct sm_ftl *ftl, loff_t offset,
+ int *zone, int *block, int *boffset)
+{
+ *boffset = offset % ftl->block_size;
+ offset /= ftl->block_size;
+ *block = offset % ftl->max_lba;
+ offset /= ftl->max_lba;
+ *zone = offset >= ftl->zone_count ? -1 : offset;
+}
+
+/* ---------------------- low level IO ------------------------------------- */
+
+static int sm_correct_sector(u8 *buffer, struct sm_oob *oob)
+{
+#ifdef CONFIG_SM_FTL_MUSEUM
+ u8 ecc[3];
+
+ __nand_calculate_ecc(buffer, SM_SMALL_PAGE, ecc);
+ if (__nand_correct_data(buffer, ecc, oob->ecc1, SM_SMALL_PAGE) < 0)
+ return -EIO;
+
+ buffer += SM_SMALL_PAGE;
+
+ __nand_calculate_ecc(buffer, SM_SMALL_PAGE, ecc);
+ if (__nand_correct_data(buffer, ecc, oob->ecc2, SM_SMALL_PAGE) < 0)
+ return -EIO;
+#endif
+ return 0;
+}
+
+/* Reads a sector + oob*/
+static int sm_read_sector(struct sm_ftl *ftl,
+ int zone, int block, int boffset,
+ u8 *buffer, struct sm_oob *oob)
+{
+ struct mtd_info *mtd = ftl->trans->mtd;
+ struct mtd_oob_ops ops;
+ struct sm_oob tmp_oob;
+ int ret;
+ int try = 0;
+
+ /* FTL can contain -1 entries that are by default filled with bits */
+ if (block == -1) {
+ memset(buffer, 0xFF, SM_SECTOR_SIZE);
+ return 0;
+ }
+
+ /* User might not need the oob, but we do for data vertification */
+ if (!oob)
+ oob = &tmp_oob;
+
+ ops.mode = ftl->smallpagenand ? MTD_OOB_RAW : MTD_OOB_PLACE;
+ ops.ooboffs = 0;
+ ops.ooblen = SM_OOB_SIZE;
+ ops.oobbuf = (void *)oob;
+ ops.len = SM_SECTOR_SIZE;
+ ops.datbuf = buffer;
+
+again:
+ /* Retrial mode */
+ if (try++) {
+ /* Avoid infinite recursion on CIS reads, sm_recheck_media
+ won't help anyway */
+ if (zone == 0 && block == ftl->cis_block && boffset ==
+ ftl->cis_boffset)
+ return ret;
+
+ /* Test if media is stable */
+ if (try == 3 || sm_recheck_media(ftl))
+ return ret;
+ }
+
+
+ /* Unfortunelly, oob read will _always_ succeed,
+ despite card removal..... */
+ ret = mtd->read_oob(mtd, sm_mkoffset(ftl, zone, block, boffset), &ops);
+
+ /* Test for unknown errors */
+ if (ret != 0 && ret != -EUCLEAN && ret != -EBADMSG) {
+ dbg("read of block %d at zone %d, failed due to error (%d)",
+ block, zone, ret);
+ goto again;
+ }
+
+ /* Do a basic test on the oob, to guard against returned garbage */
+ if (oob->reserved != 0xFFFFFFFF)
+ goto again;
+
+ /* This should never happen, unless there is a bug in the mtd driver */
+ WARN_ON(ops.oobretlen != SM_OOB_SIZE);
+ WARN_ON(buffer && ops.retlen != SM_SECTOR_SIZE);
+
+ if (!buffer)
+ return 0;
+
+ /* Test if sector marked as bad */
+ if (!sm_sector_valid(oob)) {
+ dbg("read of block %d at zone %d, failed because it is marked"
+ " as bad" , block, zone);
+ goto again;
+ }
+
+ /* Test ECC*/
+ if (ret == -EBADMSG ||
+ (ftl->smallpagenand && sm_correct_sector(buffer, oob))) {
+
+ dbg("read of block %d at zone %d, failed due to ECC error",
+ block, zone);
+ goto again;
+ }
+
+ return 0;
+}
+
+/* Writes a sector to media */
+static int sm_write_sector(struct sm_ftl *ftl,
+ int zone, int block, int boffset,
+ u8 *buffer, struct sm_oob *oob)
+{
+ struct mtd_oob_ops ops;
+ struct mtd_info *mtd = ftl->trans->mtd;
+ int ret;
+
+ BUG_ON(ftl->readonly);
+
+ if (zone == 0 && (block == ftl->cis_block || block == 0)) {
+ dbg("attempted to write the CIS!");
+ return -EIO;
+ }
+
+ if (ftl->unstable)
+ return -EIO;
+
+ ops.mode = ftl->smallpagenand ? MTD_OOB_RAW : MTD_OOB_PLACE;
+ ops.len = SM_SECTOR_SIZE;
+ ops.datbuf = buffer;
+ ops.ooboffs = 0;
+ ops.ooblen = SM_OOB_SIZE;
+ ops.oobbuf = (void *)oob;
+
+ ret = mtd->write_oob(mtd, sm_mkoffset(ftl, zone, block, boffset), &ops);
+
+ /* Now we assume that hardware will catch write bitflip errors */
+ /* If you are paranoid, use CONFIG_MTD_NAND_VERIFY_WRITE */
+
+ if (ret) {
+ dbg("write to block %d at zone %d, failed with error %d",
+ block, zone, ret);
+
+ sm_recheck_media(ftl);
+ return ret;
+ }
+
+ /* This should never happen, unless there is a bug in the driver */
+ WARN_ON(ops.oobretlen != SM_OOB_SIZE);
+ WARN_ON(buffer && ops.retlen != SM_SECTOR_SIZE);
+
+ return 0;
+}
+
+/* ------------------------ block IO ------------------------------------- */
+
+/* Write a block using data and lba, and invalid sector bitmap */
+static int sm_write_block(struct sm_ftl *ftl, u8 *buf,
+ int zone, int block, int lba,
+ unsigned long invalid_bitmap)
+{
+ struct sm_oob oob;
+ int boffset;
+ int retry = 0;
+
+ /* Initialize the oob with requested values */
+ memset(&oob, 0xFF, SM_OOB_SIZE);
+ sm_write_lba(&oob, lba);
+restart:
+ for (boffset = 0; boffset < ftl->block_size;
+ boffset += SM_SECTOR_SIZE) {
+
+ oob.data_status = 0xFF;
+
+ if (test_bit(boffset / SM_SECTOR_SIZE, &invalid_bitmap)) {
+
+ sm_printk("sector %d of block at LBA %d of zone %d"
+ " coudn't be read, marking it as invalid",
+ boffset / SM_SECTOR_SIZE, lba, zone);
+
+ oob.data_status = 0;
+ }
+
+#ifdef CONFIG_SM_FTL_MUSEUM
+ if (ftl->smallpagenand) {
+ __nand_calculate_ecc(buf + boffset,
+ SM_SMALL_PAGE, oob.ecc1);
+
+ __nand_calculate_ecc(buf + boffset + SM_SMALL_PAGE,
+ SM_SMALL_PAGE, oob.ecc2);
+ }
+#endif
+ if (!sm_write_sector(ftl, zone, block, boffset,
+ buf + boffset, &oob))
+ continue;
+
+ if (!retry) {
+
+ /* If write fails. try to erase the block */
+ /* This is safe, because we never write in blocks
+ that contain valuable data.
+ This is intended to repair block that are marked
+ as erased, but that isn't fully erased*/
+
+ if (sm_erase_block(ftl, zone, block, 0))
+ return -EIO;
+
+ retry = 1;
+ goto restart;
+ } else {
+ sm_mark_block_bad(ftl, zone, block);
+ return -EIO;
+ }
+ }
+ return 0;
+}
+
+
+/* Mark whole block at offset 'offs' as bad. */
+static void sm_mark_block_bad(struct sm_ftl *ftl, int zone, int block)
+{
+ struct sm_oob oob;
+ int boffset;
+
+ memset(&oob, 0xFF, SM_OOB_SIZE);
+ oob.block_status = 0xF0;
+
+ if (ftl->unstable)
+ return;
+
+ if (sm_recheck_media(ftl))
+ return;
+
+ sm_printk("marking block %d of zone %d as bad", block, zone);
+
+ /* We aren't checking the return value, because we don't care */
+ /* This also fails on fake xD cards, but I guess these won't expose
+ any bad blocks till fail completly */
+ for (boffset = 0; boffset < ftl->block_size; boffset += SM_SECTOR_SIZE)
+ sm_write_sector(ftl, zone, block, boffset, NULL, &oob);
+}
+
+/*
+ * Erase a block within a zone
+ * If erase succedes, it updates free block fifo, otherwise marks block as bad
+ */
+static int sm_erase_block(struct sm_ftl *ftl, int zone_num, u16 block,
+ int put_free)
+{
+ struct ftl_zone *zone = &ftl->zones[zone_num];
+ struct mtd_info *mtd = ftl->trans->mtd;
+ struct erase_info erase;
+
+ erase.mtd = mtd;
+ erase.callback = sm_erase_callback;
+ erase.addr = sm_mkoffset(ftl, zone_num, block, 0);
+ erase.len = ftl->block_size;
+ erase.priv = (u_long)ftl;
+
+ if (ftl->unstable)
+ return -EIO;
+
+ BUG_ON(ftl->readonly);
+
+ if (zone_num == 0 && (block == ftl->cis_block || block == 0)) {
+ sm_printk("attempted to erase the CIS!");
+ return -EIO;
+ }
+
+ if (mtd->erase(mtd, &erase)) {
+ sm_printk("erase of block %d in zone %d failed",
+ block, zone_num);
+ goto error;
+ }
+
+ if (erase.state == MTD_ERASE_PENDING)
+ wait_for_completion(&ftl->erase_completion);
+
+ if (erase.state != MTD_ERASE_DONE) {
+ sm_printk("erase of block %d in zone %d failed after wait",
+ block, zone_num);
+ goto error;
+ }
+
+ if (put_free)
+ kfifo_in(&zone->free_sectors,
+ (const unsigned char *)&block, sizeof(block));
+
+ return 0;
+error:
+ sm_mark_block_bad(ftl, zone_num, block);
+ return -EIO;
+}
+
+static void sm_erase_callback(struct erase_info *self)
+{
+ struct sm_ftl *ftl = (struct sm_ftl *)self->priv;
+ complete(&ftl->erase_completion);
+}
+
+/* Throughtly test that block is valid. */
+static int sm_check_block(struct sm_ftl *ftl, int zone, int block)
+{
+ int boffset;
+ struct sm_oob oob;
+ int lbas[] = { -3, 0, 0, 0 };
+ int i = 0;
+ int test_lba;
+
+
+ /* First just check that block doesn't look fishy */
+ /* Only blocks that are valid or are sliced in two parts, are
+ accepted */
+ for (boffset = 0; boffset < ftl->block_size;
+ boffset += SM_SECTOR_SIZE) {
+
+ /* This shoudn't happen anyway */
+ if (sm_read_sector(ftl, zone, block, boffset, NULL, &oob))
+ return -2;
+
+ test_lba = sm_read_lba(&oob);
+
+ if (lbas[i] != test_lba)
+ lbas[++i] = test_lba;
+
+ /* If we found three different LBAs, something is fishy */
+ if (i == 3)
+ return -EIO;
+ }
+
+ /* If the block is sliced (partialy erased usually) erase it */
+ if (i == 2) {
+ sm_erase_block(ftl, zone, block, 1);
+ return 1;
+ }
+
+ return 0;
+}
+
+/* ----------------- media scanning --------------------------------- */
+static const struct chs_entry chs_table[] = {
+ { 1, 125, 4, 4 },
+ { 2, 125, 4, 8 },
+ { 4, 250, 4, 8 },
+ { 8, 250, 4, 16 },
+ { 16, 500, 4, 16 },
+ { 32, 500, 8, 16 },
+ { 64, 500, 8, 32 },
+ { 128, 500, 16, 32 },
+ { 256, 1000, 16, 32 },
+ { 512, 1015, 32, 63 },
+ { 1024, 985, 33, 63 },
+ { 2048, 985, 33, 63 },
+ { 0 },
+};
+
+
+static const u8 cis_signature[] = {
+ 0x01, 0x03, 0xD9, 0x01, 0xFF, 0x18, 0x02, 0xDF, 0x01, 0x20
+};
+/* Find out media parameters.
+ * This ideally has to be based on nand id, but for now device size is enough */
+int sm_get_media_info(struct sm_ftl *ftl, struct mtd_info *mtd)
+{
+ int i;
+ int size_in_megs = mtd->size / (1024 * 1024);
+
+ ftl->readonly = mtd->type == MTD_ROM;
+
+ /* Manual settings for very old devices */
+ ftl->zone_count = 1;
+ ftl->smallpagenand = 0;
+
+ switch (size_in_megs) {
+ case 1:
+ /* 1 Mb flash/rom SmartMedia card (256 byte pages)*/
+ ftl->zone_size = 256;
+ ftl->max_lba = 250;
+ ftl->block_size = 8 * SM_SECTOR_SIZE;
+ ftl->smallpagenand = 1;
+
+ break;
+ case 2:
+ /* 2 Mb flash SmartMedia (256 byte pages)*/
+ if (mtd->writesize == SM_SMALL_PAGE) {
+ ftl->zone_size = 512;
+ ftl->max_lba = 500;
+ ftl->block_size = 8 * SM_SECTOR_SIZE;
+ ftl->smallpagenand = 1;
+ /* 2 Mb rom SmartMedia */
+ } else {
+
+ if (!ftl->readonly)
+ return -ENODEV;
+
+ ftl->zone_size = 256;
+ ftl->max_lba = 250;
+ ftl->block_size = 16 * SM_SECTOR_SIZE;
+ }
+ break;
+ case 4:
+ /* 4 Mb flash/rom SmartMedia device */
+ ftl->zone_size = 512;
+ ftl->max_lba = 500;
+ ftl->block_size = 16 * SM_SECTOR_SIZE;
+ break;
+ case 8:
+ /* 8 Mb flash/rom SmartMedia device */
+ ftl->zone_size = 1024;
+ ftl->max_lba = 1000;
+ ftl->block_size = 16 * SM_SECTOR_SIZE;
+ }
+
+ /* Minimum xD size is 16M. Also, all xD cards have standard zone
+ sizes. SmartMedia cards exist up to 128 Mb and have same layout*/
+ if (size_in_megs >= 16) {
+ ftl->zone_count = size_in_megs / 16;
+ ftl->zone_size = 1024;
+ ftl->max_lba = 1000;
+ ftl->block_size = 32 * SM_SECTOR_SIZE;
+ }
+
+ /* Test for proper write,erase and oob sizes */
+ if (mtd->erasesize > ftl->block_size)
+ return -ENODEV;
+
+ if (mtd->writesize > SM_SECTOR_SIZE)
+ return -ENODEV;
+
+ if (ftl->smallpagenand && mtd->oobsize < SM_SMALL_OOB_SIZE)
+ return -ENODEV;
+
+ if (!ftl->smallpagenand && mtd->oobsize < SM_OOB_SIZE)
+ return -ENODEV;
+
+ /* We use these functions for IO */
+ if (!mtd->read_oob || !mtd->write_oob)
+ return -ENODEV;
+
+ /* Find geometry information */
+ for (i = 0 ; i < ARRAY_SIZE(chs_table) ; i++) {
+ if (chs_table[i].size == size_in_megs) {
+ ftl->cylinders = chs_table[i].cyl;
+ ftl->heads = chs_table[i].head;
+ ftl->sectors = chs_table[i].sec;
+ return 0;
+ }
+ }
+
+ sm_printk("media has unknown size : %dMB", size_in_megs);
+ ftl->cylinders = 985;
+ ftl->heads = 33;
+ ftl->sectors = 63;
+ return 0;
+}
+
+/* Validate the CIS */
+static int sm_read_cis(struct sm_ftl *ftl)
+{
+ struct sm_oob oob;
+
+ if (sm_read_sector(ftl,
+ 0, ftl->cis_block, ftl->cis_boffset, ftl->cis_buffer, &oob))
+ return -EIO;
+
+ if (!sm_sector_valid(&oob) || !sm_block_valid(&oob))
+ return -EIO;
+
+ if (!memcmp(ftl->cis_buffer, cis_signature, sizeof(cis_signature)))
+ return 0;
+
+ if (!memcmp(ftl->cis_buffer + SM_SMALL_PAGE, cis_signature,
+ sizeof(cis_signature)))
+ return 0;
+ return -EIO;
+}
+
+/* Scan the media for the CIS */
+static int sm_find_cis(struct sm_ftl *ftl)
+{
+ struct sm_oob oob;
+ int block, boffset;
+ int block_found = 0;
+
+ /* Search for first valid block */
+ for (block = 0 ; block < ftl->zone_size - ftl->max_lba ; block++) {
+
+ if (sm_read_sector(ftl, 0, block, 0, NULL, &oob))
+ continue;
+
+ if (!sm_block_valid(&oob))
+ continue;
+ block_found = 1;
+ break;
+ }
+
+ if (!block_found)
+ return -EIO;
+
+ /* Search for first valid sector in this block */
+ for (boffset = 0 ; boffset < ftl->block_size;
+ boffset += SM_SECTOR_SIZE) {
+
+ if (sm_read_sector(ftl, 0, block, boffset, NULL, &oob))
+ continue;
+
+ if (!sm_sector_valid(&oob))
+ continue;
+ break;
+ }
+
+ if (boffset == ftl->block_size)
+ return -EIO;
+
+ ftl->cis_block = block;
+ ftl->cis_boffset = boffset;
+
+ if (!sm_read_cis(ftl)) {
+ dbg("CIS block found at offset %d",
+ block * ftl->block_size + boffset);
+ return 0;
+ }
+
+ return -EIO;
+}
+
+/* Basic test to determine if underlying mtd device if functional */
+static int sm_recheck_media(struct sm_ftl *ftl)
+{
+ if (sm_read_cis(ftl)) {
+
+ if (!ftl->unstable) {
+ sm_printk("media unstable, not allowing writes");
+ ftl->unstable = 1;
+ }
+ return -EIO;
+ }
+ return 0;
+}
+
+/* Initialize a FTL zone */
+static int sm_init_zone(struct sm_ftl *ftl, int zone_num)
+{
+ struct ftl_zone *zone = &ftl->zones[zone_num];
+ struct sm_oob oob;
+ u16 block;
+ int lba;
+ int i = 0;
+
+ dbg("initializing zone %d", zone_num);
+
+ /* Allocate memory for FTL table */
+ zone->lba_to_phys_table = kmalloc(ftl->max_lba * 2, GFP_KERNEL);
+
+ if (!zone->lba_to_phys_table)
+ return -ENOMEM;
+ memset(zone->lba_to_phys_table, -1, ftl->max_lba * 2);
+
+
+ /* Allocate memory for free sectors FIFO */
+ if (kfifo_alloc(&zone->free_sectors, ftl->zone_size * 2, GFP_KERNEL)) {
+ kfree(zone->lba_to_phys_table);
+ return -ENOMEM;
+ }
+
+ /* Now scan the zone */
+ for (block = 0 ; block < ftl->zone_size ; block++) {
+
+ /* Skip blocks till the CIS (including) */
+ if (zone_num == 0 && block <= ftl->cis_block)
+ continue;
+
+ /* Read the oob of first sector */
+ if (sm_read_sector(ftl, zone_num, block, 0, NULL, &oob))
+ return -EIO;
+
+ /* Test to see if block is erased. It is enough to test
+ first sector, because erase happens in one shot */
+ if (sm_block_erased(&oob)) {
+ kfifo_in(&zone->free_sectors,
+ (unsigned char *)&block, 2);
+ continue;
+ }
+
+ /* If block is marked as bad, skip it */
+ /* This assumes we can trust first sector*/
+ /* However the way the block valid status is defined, ensures
+ very low probability of failure here */
+ if (!sm_block_valid(&oob)) {
+ dbg("PH %04d <-> <marked bad>", block);
+ continue;
+ }
+
+
+ lba = sm_read_lba(&oob);
+
+ /* Invalid LBA means that block is damaged. */
+ /* We can try to erase it, or mark it as bad, but
+ lets leave that to recovery application */
+ if (lba == -2 || lba >= ftl->max_lba) {
+ dbg("PH %04d <-> LBA %04d(bad)", block, lba);
+ continue;
+ }
+
+
+ /* If there is no collision,
+ just put the sector in the FTL table */
+ if (zone->lba_to_phys_table[lba] < 0) {
+ dbg("PH %04d <-> LBA %04d", block, lba);
+ zone->lba_to_phys_table[lba] = block;
+ continue;
+ }
+
+ sm_printk("collision"
+ " of LBA %d between blocks %d and %d in zone %d",
+ lba, zone->lba_to_phys_table[lba], block, zone_num);
+
+ /* Test that this block is valid*/
+ if (sm_check_block(ftl, zone_num, block))
+ continue;
+
+ /* Test now the old block */
+ if (sm_check_block(ftl, zone_num,
+ zone->lba_to_phys_table[lba])) {
+ zone->lba_to_phys_table[lba] = block;
+ continue;
+ }
+
+ /* If both blocks are valid and share same LBA, it means that
+ they hold different versions of same data. It not
+ known which is more recent, thus just erase one of them
+ */
+ sm_printk("both blocks are valid, erasing the later");
+ sm_erase_block(ftl, zone_num, block, 1);
+ }
+
+ dbg("zone initialized");
+ zone->initialized = 1;
+
+ /* No free sectors, means that the zone is heavily damaged, write won't
+ work, but it can still can be (partially) read */
+ if (!kfifo_len(&zone->free_sectors)) {
+ sm_printk("no free blocks in zone %d", zone_num);
+ return 0;
+ }
+
+ /* Randomize first block we write to */
+ get_random_bytes(&i, 2);
+ i %= (kfifo_len(&zone->free_sectors) / 2);
+
+ while (i--) {
+ kfifo_out(&zone->free_sectors, (unsigned char *)&block, 2);
+ kfifo_in(&zone->free_sectors, (const unsigned char *)&block, 2);
+ }
+ return 0;
+}
+
+/* Get and automaticly initialize an FTL mapping for one zone */
+struct ftl_zone *sm_get_zone(struct sm_ftl *ftl, int zone_num)
+{
+ struct ftl_zone *zone;
+ int error;
+
+ BUG_ON(zone_num >= ftl->zone_count);
+ zone = &ftl->zones[zone_num];
+
+ if (!zone->initialized) {
+ error = sm_init_zone(ftl, zone_num);
+
+ if (error)
+ return ERR_PTR(error);
+ }
+ return zone;
+}
+
+
+/* ----------------- cache handling ------------------------------------------*/
+
+/* Initialize the one block cache */
+void sm_cache_init(struct sm_ftl *ftl)
+{
+ ftl->cache_data_invalid_bitmap = 0xFFFFFFFF;
+ ftl->cache_clean = 1;
+ ftl->cache_zone = -1;
+ ftl->cache_block = -1;
+ /*memset(ftl->cache_data, 0xAA, ftl->block_size);*/
+}
+
+/* Put sector in one block cache */
+void sm_cache_put(struct sm_ftl *ftl, char *buffer, int boffset)
+{
+ memcpy(ftl->cache_data + boffset, buffer, SM_SECTOR_SIZE);
+ clear_bit(boffset / SM_SECTOR_SIZE, &ftl->cache_data_invalid_bitmap);
+ ftl->cache_clean = 0;
+}
+
+/* Read a sector from the cache */
+int sm_cache_get(struct sm_ftl *ftl, char *buffer, int boffset)
+{
+ if (test_bit(boffset / SM_SECTOR_SIZE,
+ &ftl->cache_data_invalid_bitmap))
+ return -1;
+
+ memcpy(buffer, ftl->cache_data + boffset, SM_SECTOR_SIZE);
+ return 0;
+}
+
+/* Write the cache to hardware */
+int sm_cache_flush(struct sm_ftl *ftl)
+{
+ struct ftl_zone *zone;
+
+ int sector_num;
+ u16 write_sector;
+ int zone_num = ftl->cache_zone;
+ int block_num;
+
+ if (ftl->cache_clean)
+ return 0;
+
+ if (ftl->unstable)
+ return -EIO;
+
+ BUG_ON(zone_num < 0);
+ zone = &ftl->zones[zone_num];
+ block_num = zone->lba_to_phys_table[ftl->cache_block];
+
+
+ /* Try to read all unread areas of the cache block*/
+ for_each_bit(sector_num, &ftl->cache_data_invalid_bitmap,
+ ftl->block_size / SM_SECTOR_SIZE) {
+
+ if (!sm_read_sector(ftl,
+ zone_num, block_num, sector_num * SM_SECTOR_SIZE,
+ ftl->cache_data + sector_num * SM_SECTOR_SIZE, NULL))
+ clear_bit(sector_num,
+ &ftl->cache_data_invalid_bitmap);
+ }
+restart:
+ /* No spare blocks */
+ /* We could still continue by erasing the current block,
+ but for such worn out media it doesn't worth the trouble,
+ and the dangers */
+
+ if (!kfifo_len(&zone->free_sectors)) {
+ dbg("no free sectors for write!");
+ return -EIO;
+ }
+
+ kfifo_out(&zone->free_sectors, (unsigned char *)&write_sector, 2);
+
+ if (sm_write_block(ftl, ftl->cache_data, zone_num, write_sector,
+ ftl->cache_block, ftl->cache_data_invalid_bitmap))
+ goto restart;
+
+ /* Update the FTL table */
+ zone->lba_to_phys_table[ftl->cache_block] = write_sector;
+
+ /* Write succesfull, so erase and free the old block */
+ if (block_num > 0)
+ sm_erase_block(ftl, zone_num, block_num, 1);
+
+ sm_cache_init(ftl);
+ return 0;
+}
+
+
+/* flush timer, runs a second after last write */
+static void sm_cache_flush_timer(unsigned long data)
+{
+ struct sm_ftl *ftl = (struct sm_ftl *)data;
+ queue_work(cache_flush_workqueue, &ftl->flush_work);
+}
+
+/* cache flush work, kicked by timer */
+static void sm_cache_flush_work(struct work_struct *work)
+{
+ struct sm_ftl *ftl = container_of(work, struct sm_ftl, flush_work);
+ mutex_lock(&ftl->mutex);
+ sm_cache_flush(ftl);
+ mutex_unlock(&ftl->mutex);
+ return;
+}
+
+/* ---------------- outside interface -------------------------------------- */
+
+/* outside interface: read a sector */
+static int sm_read(struct mtd_blktrans_dev *dev,
+ unsigned long sect_no, char *buf)
+{
+ struct sm_ftl *ftl = dev->priv;
+ struct ftl_zone *zone;
+ int error = 0, in_cache = 0;
+ int zone_num, block, boffset;
+
+ sm_break_offset(ftl, sect_no << 9, &zone_num, &block, &boffset);
+ mutex_lock(&ftl->mutex);
+
+
+ zone = sm_get_zone(ftl, zone_num);
+ if (IS_ERR(zone)) {
+ error = PTR_ERR(zone);
+ goto unlock;
+ }
+
+ /* Have to look at cache first */
+ if (ftl->cache_zone == zone_num && ftl->cache_block == block) {
+ in_cache = 1;
+ if (!sm_cache_get(ftl, buf, boffset))
+ goto unlock;
+ }
+
+ /* Translate the block and return if doesn't exist in the table */
+ block = zone->lba_to_phys_table[block];
+
+ if (block == -1) {
+ memset(buf, 0xFF, SM_SECTOR_SIZE);
+ goto unlock;
+ }
+
+ if (sm_read_sector(ftl, zone_num, block, boffset, buf, NULL)) {
+ error = -EIO;
+ goto unlock;
+ }
+
+ if (in_cache)
+ sm_cache_put(ftl, buf, boffset);
+unlock:
+ mutex_unlock(&ftl->mutex);
+ return error;
+}
+
+/* outside interface: write a sector */
+static int sm_write(struct mtd_blktrans_dev *dev,
+ unsigned long sec_no, char *buf)
+{
+ struct sm_ftl *ftl = dev->priv;
+ struct ftl_zone *zone;
+ int error, zone_num, block, boffset;
+
+ BUG_ON(ftl->readonly);
+ sm_break_offset(ftl, sec_no << 9, &zone_num, &block, &boffset);
+
+ /* No need in flush thread running now */
+ del_timer(&ftl->timer);
+ mutex_lock(&ftl->mutex);
+
+ zone = sm_get_zone(ftl, zone_num);
+ if (IS_ERR(zone)) {
+ error = PTR_ERR(zone);
+ goto unlock;
+ }
+
+ /* If entry is not in cache, flush it */
+ if (ftl->cache_block != block || ftl->cache_zone != zone_num) {
+
+ error = sm_cache_flush(ftl);
+ if (error)
+ goto unlock;
+
+ ftl->cache_block = block;
+ ftl->cache_zone = zone_num;
+ }
+
+ sm_cache_put(ftl, buf, boffset);
+unlock:
+ mod_timer(&ftl->timer, jiffies + msecs_to_jiffies(cache_timeout));
+ mutex_unlock(&ftl->mutex);
+ return error;
+}
+
+/* outside interface: flush everything */
+static int sm_flush(struct mtd_blktrans_dev *dev)
+{
+ struct sm_ftl *ftl = dev->priv;
+ int retval;
+
+ mutex_lock(&ftl->mutex);
+ retval = sm_cache_flush(ftl);
+ mutex_unlock(&ftl->mutex);
+ return retval;
+}
+
+/* outside interface: device is released */
+static int sm_release(struct mtd_blktrans_dev *dev)
+{
+ struct sm_ftl *ftl = dev->priv;
+
+ mutex_lock(&ftl->mutex);
+ del_timer_sync(&ftl->timer);
+ cancel_work_sync(&ftl->flush_work);
+ sm_cache_flush(ftl);
+ mutex_unlock(&ftl->mutex);
+ return 0;
+}
+
+/* outside interface: get geometry */
+static int sm_getgeo(struct mtd_blktrans_dev *dev, struct hd_geometry *geo)
+{
+ struct sm_ftl *ftl = dev->priv;
+ geo->heads = ftl->heads;
+ geo->sectors = ftl->sectors;
+ geo->cylinders = ftl->cylinders;
+ return 0;
+}
+
+/* external interface: main initialization function */
+static void sm_add_mtd(struct mtd_blktrans_ops *tr, struct mtd_info *mtd)
+{
+ struct mtd_blktrans_dev *trans;
+ struct sm_ftl *ftl;
+
+ /* Allocate & initialize our private structure */
+ ftl = kzalloc(sizeof(struct sm_ftl), GFP_KERNEL);
+ if (!ftl)
+ goto error1;
+
+ mutex_init(&ftl->mutex);
+ setup_timer(&ftl->timer, sm_cache_flush_timer, (unsigned long)ftl);
+ INIT_WORK(&ftl->flush_work, sm_cache_flush_work);
+ init_completion(&ftl->erase_completion);
+
+
+ /* Read media information */
+ if (sm_get_media_info(ftl, mtd))
+ goto error2;
+
+ /* Allocate temporary CIS buffer for read retry support */
+ ftl->cis_buffer = kzalloc(SM_SECTOR_SIZE, GFP_KERNEL);
+ if (!ftl->cis_buffer)
+ goto error2;
+
+ /* Allocate zone array, it will be initialized on demand */
+ ftl->zones = kzalloc(sizeof(struct ftl_zone) * ftl->zone_count,
+ GFP_KERNEL);
+ if (!ftl->zones)
+ goto error3;
+
+ /* Allocate the cache*/
+ ftl->cache_data = kzalloc(ftl->block_size, GFP_KERNEL);
+
+ if (!ftl->cache_data)
+ goto error4;
+
+ sm_cache_init(ftl);
+
+ /* Allocate upper layer structure and initialize it */
+ trans = kzalloc(sizeof(struct mtd_blktrans_dev), GFP_KERNEL);
+ if (!trans)
+ goto error5;
+
+ ftl->trans = trans;
+ trans->priv = ftl;
+
+ trans->tr = tr;
+ trans->mtd = mtd;
+ trans->devnum = -1;
+ trans->size = (ftl->block_size * ftl->max_lba * ftl->zone_count) >> 9;
+ trans->readonly = ftl->readonly;
+
+
+ if (sm_find_cis(ftl))
+ goto error6;
+
+ trans->disk_attributes = sm_create_sysfs_attributes(ftl);
+
+ sm_printk("Found %d MiB xD/SmartMedia FTL on mtd%d",
+ (int)(mtd->size / (1024 * 1024)), mtd->index);
+
+ dbg("FTL layout:");
+ dbg("%d zone(s), each consists of %d blocks (+%d spares)",
+ ftl->zone_count, ftl->max_lba,
+ ftl->zone_size - ftl->max_lba);
+ dbg("each block consists of %d bytes",
+ ftl->block_size);
+
+ /* Register device*/
+ if (add_mtd_blktrans_dev(trans))
+ goto error6;
+
+ return;
+error6:
+ kfree(trans);
+error5:
+ kfree(ftl->cache_data);
+error4:
+ kfree(ftl->zones);
+error3:
+ kfree(ftl->cis_buffer);
+error2:
+ kfree(ftl);
+error1:
+ return;
+}
+
+/* main interface: device {surprise,} removal */
+static void sm_remove_dev(struct mtd_blktrans_dev *dev)
+{
+ struct sm_ftl *ftl = dev->priv;
+ int i;
+
+ del_mtd_blktrans_dev(dev);
+
+ for (i = 0 ; i < ftl->zone_count; i++) {
+
+ if (!ftl->zones[i].initialized)
+ continue;
+
+ kfree(ftl->zones[i].lba_to_phys_table);
+ kfifo_free(&ftl->zones[i].free_sectors);
+ }
+
+ sm_delete_sysfs_attributes(ftl);
+ kfree(ftl->zones);
+ kfree(ftl->cache_data);
+ kfree(ftl);
+}
+
+static struct mtd_blktrans_ops sm_ftl_ops = {
+ .name = "smblk",
+ .major = -1,
+ .part_bits = SM_FTL_PARTN_BITS,
+ .blksize = SM_SECTOR_SIZE,
+ .getgeo = sm_getgeo,
+
+ .add_mtd = sm_add_mtd,
+ .remove_dev = sm_remove_dev,
+
+ .readsect = sm_read,
+ .writesect = sm_write,
+
+ .flush = sm_flush,
+ .release = sm_release,
+
+ .owner = THIS_MODULE,
+};
+
+static __init int sm_module_init(void)
+{
+ int error = 0;
+ cache_flush_workqueue = create_freezeable_workqueue("smflush");
+
+ if (IS_ERR(cache_flush_workqueue))
+ return PTR_ERR(cache_flush_workqueue);
+
+ error = register_mtd_blktrans(&sm_ftl_ops);
+ if (error)
+ destroy_workqueue(cache_flush_workqueue);
+ return error;
+
+}
+
+static void __exit sm_module_exit(void)
+{
+ destroy_workqueue(cache_flush_workqueue);
+ deregister_mtd_blktrans(&sm_ftl_ops);
+}
+
+module_init(sm_module_init);
+module_exit(sm_module_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Maxim Levitsky <[email protected]>");
+MODULE_DESCRIPTION("Smartmedia/xD mtd translation layer");
diff --git a/drivers/mtd/sm_ftl.h b/drivers/mtd/sm_ftl.h
new file mode 100644
index 0000000..e3941f4
--- /dev/null
+++ b/drivers/mtd/sm_ftl.h
@@ -0,0 +1,92 @@
+/*
+ * Copyright (C) 2009 - Maxim Levitsky
+ * SmartMedia/xD translation layer
+ *
+ * Based loosly on ssfdc.c which is
+ * (c) 2005 Eptar srl
+ * Author: Claudio Lanconelli <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/mtd/blktrans.h>
+#include <linux/kfifo.h>
+#include <linux/sched.h>
+#include <linux/completion.h>
+
+
+
+struct ftl_zone {
+ int initialized;
+ s16 *lba_to_phys_table; /* LBA to physical table */
+ struct kfifo free_sectors; /* queue of free sectors */
+};
+
+struct sm_ftl {
+ struct mtd_blktrans_dev *trans;
+
+ struct mutex mutex; /* protects the structure */
+ struct ftl_zone *zones; /* FTL tables for each zone */
+
+ /* Media information */
+ int block_size; /* block size in bytes */
+ int zone_size; /* zone size in blocks */
+ int zone_count; /* number of zones */
+ int max_lba; /* maximum lba in a zone */
+ int smallpagenand; /* 256 bytes/page nand */
+ int readonly; /* is FS readonly */
+ int unstable;
+ int cis_block; /* CIS block location */
+ int cis_boffset; /* CIS offset in the block */
+ void *cis_buffer; /* tmp buffer for cis reads */
+
+ /* Cache */
+ int cache_block; /* block number of cached block */
+ int cache_zone; /* zone of cached block */
+ unsigned char *cache_data; /* cached block data */
+ long unsigned int cache_data_invalid_bitmap;
+ int cache_clean;
+ struct work_struct flush_work;
+ struct timer_list timer;
+
+ /* Async erase stuff */
+ struct completion erase_completion;
+
+ /* Geometry stuff */
+ int heads;
+ int sectors;
+ int cylinders;
+};
+
+struct chs_entry {
+ unsigned long size;
+ unsigned short cyl;
+ unsigned char head;
+ unsigned char sec;
+};
+
+
+#define SM_FTL_PARTN_BITS 3
+
+#define sm_printk(format, ...) \
+ printk(KERN_WARNING "sm_ftl" ": " format "\n", ## __VA_ARGS__)
+
+
+#ifdef __DEBUG
+
+#define dbg(format, ...) \
+ printk(KERN_DEBUG "sm_ftl" ": " format "\n", ## __VA_ARGS__)
+#else
+
+#define dbg(format, ...)
+
+#endif
+
+static void sm_erase_callback(struct erase_info *self);
+static int sm_erase_block(struct sm_ftl *ftl, int zone_num, u16 block,
+ int put_free);
+static void sm_mark_block_bad(struct sm_ftl *ftl, int zone_num, int block);
+
+static int sm_recheck_media(struct sm_ftl *ftl);
--
1.6.3.3
On Sat, 30 Jan 2010, Maxim Levitsky wrote:
> This patch adds tracking for open and close calls.
> Now trans ->open and ->release are never called twise in a row
> ->release is also called once before mtd device disappers
> ...
> --- a/drivers/mtd/mtd_blkdevs.c
> +++ b/drivers/mtd/mtd_blkdevs.c
> @@ -128,6 +128,9 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode)
> if (!get_mtd_device(NULL, dev->mtd->index))
> goto out;
>
> + if (dev->open++)
> + goto out;
> +
> if (!try_module_get(tr->owner))
> goto out_tr;
>
> @@ -153,6 +156,10 @@ static int blktrans_release(struct gendisk *disk, fmode_t mode)
> struct mtd_blktrans_ops *tr = dev->tr;
> int ret = 0;
>
> + dev->open--;
> + if (dev->open)
> + return 0;
> +
Just a very minor quibble: if you use if (dev->open++) in one function,
why not use if (--dev->open) in the other? Or separate the
increment/decrement from the test, depending on you style preferences.
/Ricard
--
Ricard Wolf Wanderl?f ricardw(at)axis.com
Axis Communications AB, Lund, Sweden http://www.axis.com
Phone +46 46 272 2016 Fax +46 46 13 61 30
On Mon, 2010-02-01 at 08:46 +0100, Ricard Wanderlof wrote:
> On Sat, 30 Jan 2010, Maxim Levitsky wrote:
>
> > This patch adds tracking for open and close calls.
> > Now trans ->open and ->release are never called twise in a row
> > ->release is also called once before mtd device disappers
> > ...
>
> > --- a/drivers/mtd/mtd_blkdevs.c
> > +++ b/drivers/mtd/mtd_blkdevs.c
> > @@ -128,6 +128,9 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode)
> > if (!get_mtd_device(NULL, dev->mtd->index))
> > goto out;
> >
> > + if (dev->open++)
> > + goto out;
> > +
> > if (!try_module_get(tr->owner))
> > goto out_tr;
> >
> > @@ -153,6 +156,10 @@ static int blktrans_release(struct gendisk *disk, fmode_t mode)
> > struct mtd_blktrans_ops *tr = dev->tr;
> > int ret = 0;
> >
> > + dev->open--;
> > + if (dev->open)
> > + return 0;
> > +
>
> Just a very minor quibble: if you use if (dev->open++) in one function,
> why not use if (--dev->open) in the other? Or separate the
> increment/decrement from the test, depending on you style preferences.
No problem, this just got lost in all the noise.
I tried all kinds of approaches to make hotplug reliable, before finally
making it be so. (It is really stable here, I didn't have any hotplug
related issues for very long time)
In fact I feel that my xd card is more stable that sd one...
(I recently found a bug in sdhci driver....)
I would be very happy to receive a full review of the patches, and get
it in the kernel.
Best regards,
Maxim Levitsky