This patch converts the cns3xxx platform to use the ehci-platform driver
instead of the ehci-cns3xxx platform driver.
The ehci-platform driver is provided with power_{on,off} callbacks to ensure
proper block gating and USB configuration of the EHCI controller.
Signed-off-by: Florian Fainelli <[email protected]>
---
No changes in v2 and v3
arch/arm/mach-cns3xxx/cns3420vb.c | 44 ++++++++++++++++++++++++++++++++++++-
1 file changed, 43 insertions(+), 1 deletion(-)
diff --git a/arch/arm/mach-cns3xxx/cns3420vb.c b/arch/arm/mach-cns3xxx/cns3420vb.c
index 2c5fb4c..906094c 100644
--- a/arch/arm/mach-cns3xxx/cns3420vb.c
+++ b/arch/arm/mach-cns3xxx/cns3420vb.c
@@ -24,6 +24,7 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/partitions.h>
+#include <linux/usb/ehci_pdriver.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/hardware/gic.h>
@@ -32,6 +33,7 @@
#include <asm/mach/time.h>
#include <mach/cns3xxx.h>
#include <mach/irqs.h>
+#include <mach/pm.h>
#include "core.h"
#include "devices.h"
@@ -125,13 +127,53 @@ static struct resource cns3xxx_usb_ehci_resources[] = {
static u64 cns3xxx_usb_ehci_dma_mask = DMA_BIT_MASK(32);
+static int csn3xxx_usb_ehci_power_on(struct platform_device *pdev)
+{
+ /*
+ * EHCI and OHCI share the same clock and power,
+ * resetting twice would cause the 1st controller been reset.
+ * Therefore only do power up at the first up device, and
+ * power down at the last down device.
+ *
+ * Set USB AHB INCR length to 16
+ */
+ if (atomic_inc_return(&usb_pwr_ref) == 1) {
+ cns3xxx_pwr_power_up(1 << PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_USB);
+ cns3xxx_pwr_clk_en(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+ cns3xxx_pwr_soft_rst(1 << PM_SOFT_RST_REG_OFFST_USB_HOST);
+ __raw_writel((__raw_readl(MISC_CHIP_CONFIG_REG) | (0X2 << 24)),
+ MISC_CHIP_CONFIG_REG);
+ }
+
+ return 0;
+}
+
+static void csn3xxx_usb_ehci_power_off(struct platform_device *pdev)
+{
+ /*
+ * EHCI and OHCI share the same clock and power,
+ * resetting twice would cause the 1st controller been reset.
+ * Therefore only do power up at the first up device, and
+ * power down at the last down device.
+ */
+ if (atomic_dec_return(&usb_pwr_ref) == 0)
+ cns3xxx_pwr_clk_dis(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+}
+
+static struct usb_ehci_pdata cns3xxx_usb_ehci_pdata = {
+ .port_power_off = 1,
+ .power_on = csn3xxx_usb_ehci_power_on,
+ .power_off = csn3xxx_usb_ehci_power_off,
+};
+
static struct platform_device cns3xxx_usb_ehci_device = {
- .name = "cns3xxx-ehci",
+ .name = "ehci-platform",
.num_resources = ARRAY_SIZE(cns3xxx_usb_ehci_resources),
.resource = cns3xxx_usb_ehci_resources,
.dev = {
.dma_mask = &cns3xxx_usb_ehci_dma_mask,
.coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &cns3xxx_usb_ehci_pdata,
},
};
--
1.7.9.5