When spi client does the spi transfer and does not sets
the bits_per_word for each transfer then set it as default
of spi device in spi core before calling low level transfer.
Removing the similar code from spi-tegra20-slink driver as
it is not required.
Signed-off-by: Laxman Dewangan <[email protected]>
Cc: Stephen Warren <[email protected]>
---
When reviewing the change
[PATCH] spi: tegra: add spi driver for SLINK controller
it was suggested by Mark and Stephen that we should move the
bits_per_word setting to the core as it almost exist in all driver.
Creating this patch for doing this.
Creating teh patch
drivers/spi/spi-tegra20-slink.c | 3 +--
drivers/spi/spi.c | 11 ++++++++++-
2 files changed, 11 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/spi-tegra20-slink.c b/drivers/spi/spi-tegra20-slink.c
index b8985be..07dc735 100644
--- a/drivers/spi/spi-tegra20-slink.c
+++ b/drivers/spi/spi-tegra20-slink.c
@@ -727,8 +727,7 @@ static int tegra_slink_start_transfer_one(struct spi_device *spi,
unsigned long command;
unsigned long command2;
- bits_per_word = t->bits_per_word ? t->bits_per_word :
- spi->bits_per_word;
+ bits_per_word = t->bits_per_word;
speed = t->speed_hz ? t->speed_hz : spi->max_speed_hz;
if (!speed)
speed = tspi->spi_max_frequency;
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index fc0da39..6891a03 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -1193,6 +1193,7 @@ EXPORT_SYMBOL_GPL(spi_setup);
static int __spi_async(struct spi_device *spi, struct spi_message *message)
{
struct spi_master *master = spi->master;
+ struct spi_transfer *xfer;
/* Half-duplex links include original MicroWire, and ones with
* only one data pin like SPI_3WIRE (switches direction) or where
@@ -1201,7 +1202,6 @@ static int __spi_async(struct spi_device *spi, struct spi_message *message)
*/
if ((master->flags & SPI_MASTER_HALF_DUPLEX)
|| (spi->mode & SPI_3WIRE)) {
- struct spi_transfer *xfer;
unsigned flags = master->flags;
list_for_each_entry(xfer, &message->transfers, transfer_list) {
@@ -1214,6 +1214,15 @@ static int __spi_async(struct spi_device *spi, struct spi_message *message)
}
}
+ /**
+ * Set transfer bits_per_word as spi device default if it is not
+ * set for this transfer.
+ */
+ list_for_each_entry(xfer, &message->transfers, transfer_list) {
+ if (!xfer->bits_per_word)
+ xfer->bits_per_word = spi->bits_per_word;
+ }
+
message->spi = spi;
message->status = -EINPROGRESS;
return master->transfer(spi, message);
--
1.7.1.1
On Fri, Nov 09, 2012 at 02:36:45PM +0530, Laxman Dewangan wrote:
> When spi client does the spi transfer and does not sets
> the bits_per_word for each transfer then set it as default
> of spi device in spi core before calling low level transfer.
>
> Removing the similar code from spi-tegra20-slink driver as
> it is not required.
Applied, thanks.
Hi,
On 9 November 2012 10:06, Laxman Dewangan <[email protected]> wrote:
> When spi client does the spi transfer and does not sets
> the bits_per_word for each transfer then set it as default
> of spi device in spi core before calling low level transfer.
I like that (not that it counts ... )!
> Removing the similar code from spi-tegra20-slink driver as
> it is not required.
Not sure if this should be part of *this* patch.
Also spi-tegra20-slink isn't the only one fixing up the bits_per_word
for transfers, so it would be nice if you could remove it from the
other drivers, too.
In a future patch, maybe even do the same with speed_hz?
Regards
Jonas