From: Michal Simek <[email protected]>
No functional changes.
Signed-off-by: Michal Simek <[email protected]>
---
Changes in v3: None
Changes in v2:
- this patch has been added
---
drivers/tty/serial/xilinx_uartps.c | 109 +++++++++++++++++--------------------
1 file changed, 49 insertions(+), 60 deletions(-)
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f619ad5b5eae..b2f929e48ddd 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -163,11 +163,11 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
/**
* struct xuartps - device data
- * @port Pointer to the UART port
- * @refclk Reference clock
- * @aperclk APB clock
- * @baud Current baud rate
- * @clk_rate_change_nb Notifier block for clock changes
+ * @port: Pointer to the UART port
+ * @refclk: Reference clock
+ * @aperclk: APB clock
+ * @baud: Current baud rate
+ * @clk_rate_change_nb: Notifier block for clock changes
*/
struct xuartps {
struct uart_port *port;
@@ -183,8 +183,8 @@ struct xuartps {
* @irq: Irq number
* @dev_id: Id of the port
*
- * Returns IRQHANDLED
- **/
+ * Return: IRQHANDLED
+ */
static irqreturn_t xuartps_isr(int irq, void *dev_id)
{
struct uart_port *port = (struct uart_port *)dev_id;
@@ -325,7 +325,7 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
* @rbdiv: BDIV value (return value)
* @rcd: CD value (return value)
* @div8: Value for clk_sel bit in mod (return value)
- * Returns baud rate, requested baud when possible, or actual baud when there
+ * Return: baud rate, requested baud when possible, or actual baud when there
* was too much error, zero if no valid divisors are found.
*
* Formula to obtain baud rate is
@@ -384,7 +384,7 @@ static unsigned int xuartps_calc_baud_divs(unsigned int clk, unsigned int baud,
* xuartps_set_baud_rate - Calculate and set the baud rate
* @port: Handle to the uart port structure
* @baud: Baud rate to set
- * Returns baud rate, requested baud when possible, or actual baud when there
+ * Return: baud rate, requested baud when possible, or actual baud when there
* was too much error, zero if no valid divisors are found.
*/
static unsigned int xuartps_set_baud_rate(struct uart_port *port,
@@ -419,7 +419,7 @@ static unsigned int xuartps_set_baud_rate(struct uart_port *port,
* @nb: Notifier block
* @event: Notify event
* @data: Notifier data
- * Returns NOTIFY_OK on success, NOTIFY_BAD on error.
+ * Return: NOTIFY_OK on success, NOTIFY_BAD on error.
*/
static int xuartps_clk_notifier_cb(struct notifier_block *nb,
unsigned long event, void *data)
@@ -514,8 +514,7 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
/**
* xuartps_start_tx - Start transmitting bytes
* @port: Handle to the uart port structure
- *
- **/
+ */
static void xuartps_start_tx(struct uart_port *port)
{
unsigned int status, numbytes = port->fifosize;
@@ -562,8 +561,7 @@ static void xuartps_start_tx(struct uart_port *port)
/**
* xuartps_stop_tx - Stop TX
* @port: Handle to the uart port structure
- *
- **/
+ */
static void xuartps_stop_tx(struct uart_port *port)
{
unsigned int regval;
@@ -577,8 +575,7 @@ static void xuartps_stop_tx(struct uart_port *port)
/**
* xuartps_stop_rx - Stop RX
* @port: Handle to the uart port structure
- *
- **/
+ */
static void xuartps_stop_rx(struct uart_port *port)
{
unsigned int regval;
@@ -593,8 +590,8 @@ static void xuartps_stop_rx(struct uart_port *port)
* xuartps_tx_empty - Check whether TX is empty
* @port: Handle to the uart port structure
*
- * Returns TIOCSER_TEMT on success, 0 otherwise
- **/
+ * Return: TIOCSER_TEMT on success, 0 otherwise
+ */
static unsigned int xuartps_tx_empty(struct uart_port *port)
{
unsigned int status;
@@ -608,8 +605,7 @@ static unsigned int xuartps_tx_empty(struct uart_port *port)
* transmitting char breaks
* @port: Handle to the uart port structure
* @ctl: Value based on which start or stop decision is taken
- *
- **/
+ */
static void xuartps_break_ctl(struct uart_port *port, int ctl)
{
unsigned int status;
@@ -636,8 +632,7 @@ static void xuartps_break_ctl(struct uart_port *port, int ctl)
* @port: Handle to the uart port structure
* @termios: Handle to the input termios structure
* @old: Values of the previously saved termios structure
- *
- **/
+ */
static void xuartps_set_termios(struct uart_port *port,
struct ktermios *termios, struct ktermios *old)
{
@@ -761,8 +756,8 @@ static void xuartps_set_termios(struct uart_port *port,
* xuartps_startup - Called when an application opens a xuartps port
* @port: Handle to the uart port structure
*
- * Returns 0 on success, negative error otherwise
- **/
+ * Return: 0 on success, negative error otherwise
+ */
static int xuartps_startup(struct uart_port *port)
{
unsigned int retval = 0, status = 0;
@@ -824,8 +819,7 @@ static int xuartps_startup(struct uart_port *port)
/**
* xuartps_shutdown - Called when an application closes a xuartps port
* @port: Handle to the uart port structure
- *
- **/
+ */
static void xuartps_shutdown(struct uart_port *port)
{
int status;
@@ -844,8 +838,8 @@ static void xuartps_shutdown(struct uart_port *port)
* xuartps_type - Set UART type to xuartps port
* @port: Handle to the uart port structure
*
- * Returns string on success, NULL otherwise
- **/
+ * Return: string on success, NULL otherwise
+ */
static const char *xuartps_type(struct uart_port *port)
{
return port->type == PORT_XUARTPS ? XUARTPS_NAME : NULL;
@@ -856,8 +850,8 @@ static const char *xuartps_type(struct uart_port *port)
* @port: Handle to the uart port structure
* @ser: Handle to the structure whose members are compared
*
- * Returns 0 if success otherwise -EINVAL
- **/
+ * Return: 0 if success otherwise -EINVAL
+ */
static int xuartps_verify_port(struct uart_port *port,
struct serial_struct *ser)
{
@@ -880,8 +874,8 @@ static int xuartps_verify_port(struct uart_port *port,
* uart_add_one_port()
* @port: Handle to the uart port structure
*
- * Returns 0, -ENOMEM if request fails
- **/
+ * Return: 0, -ENOMEM if request fails
+ */
static int xuartps_request_port(struct uart_port *port)
{
if (!request_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE,
@@ -903,8 +897,7 @@ static int xuartps_request_port(struct uart_port *port)
* port, called when the driver removes a xuartps
* port via uart_remove_one_port().
* @port: Handle to the uart port structure
- *
- **/
+ */
static void xuartps_release_port(struct uart_port *port)
{
release_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE);
@@ -917,8 +910,7 @@ static void xuartps_release_port(struct uart_port *port)
* xuartps port
* @port: Handle to the uart port structure
* @flags: If any
- *
- **/
+ */
static void xuartps_config_port(struct uart_port *port, int flags)
{
if (flags & UART_CONFIG_TYPE && xuartps_request_port(port) == 0)
@@ -930,9 +922,8 @@ static void xuartps_config_port(struct uart_port *port, int flags)
*
* @port: Handle to the uart port structure
*
- * Returns the modem control state
- *
- **/
+ * Return: the modem control state
+ */
static unsigned int xuartps_get_mctrl(struct uart_port *port)
{
return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
@@ -1040,8 +1031,8 @@ static struct uart_port xuartps_port[2];
* xuartps_get_port - Configure the port from the platform device resource
* info
*
- * Returns a pointer to a uart_port or NULL for failure
- **/
+ * Return: a pointer to a uart_port or NULL for failure
+ */
static struct uart_port *xuartps_get_port(void)
{
struct uart_port *port;
@@ -1078,8 +1069,7 @@ static struct uart_port *xuartps_get_port(void)
/**
* xuartps_console_wait_tx - Wait for the TX to be full
* @port: Handle to the uart port structure
- *
- **/
+ */
static void xuartps_console_wait_tx(struct uart_port *port)
{
while ((xuartps_readl(XUARTPS_SR_OFFSET) & XUARTPS_SR_TXEMPTY)
@@ -1091,8 +1081,7 @@ static void xuartps_console_wait_tx(struct uart_port *port)
* xuartps_console_putchar - write the character to the FIFO buffer
* @port: Handle to the uart port structure
* @ch: Character to be written
- *
- **/
+ */
static void xuartps_console_putchar(struct uart_port *port, int ch)
{
xuartps_console_wait_tx(port);
@@ -1101,10 +1090,10 @@ static void xuartps_console_putchar(struct uart_port *port, int ch)
/**
* xuartps_console_write - perform write operation
- * @port: Handle to the uart port structure
+ * @co: Console handle
* @s: Pointer to character array
* @count: No of characters
- **/
+ */
static void xuartps_console_write(struct console *co, const char *s,
unsigned int count)
{
@@ -1151,8 +1140,8 @@ static void xuartps_console_write(struct console *co, const char *s,
* @co: Console handle
* @options: Initial settings of uart
*
- * Returns 0, -ENODEV if no device
- **/
+ * Return: 0, -ENODEV if no device
+ */
static int __init xuartps_console_setup(struct console *co, char *options)
{
struct uart_port *port = &xuartps_port[co->index];
@@ -1190,8 +1179,8 @@ static struct console xuartps_console = {
/**
* xuartps_console_init - Initialization call
*
- * Returns 0 on success, negative error otherwise
- **/
+ * Return: 0 on success, negative error otherwise
+ */
static int __init xuartps_console_init(void)
{
register_console(&xuartps_console);
@@ -1221,7 +1210,7 @@ static struct uart_driver xuartps_uart_driver = {
* xuartps_suspend - suspend event
* @device: Pointer to the device structure
*
- * Returns 0
+ * Return: 0
*/
static int xuartps_suspend(struct device *device)
{
@@ -1269,7 +1258,7 @@ static int xuartps_suspend(struct device *device)
* xuartps_resume - Resume after a previous suspend
* @device: Pointer to the device structure
*
- * Returns 0
+ * Return: 0
*/
static int xuartps_resume(struct device *device)
{
@@ -1336,8 +1325,8 @@ static SIMPLE_DEV_PM_OPS(xuartps_dev_pm_ops, xuartps_suspend, xuartps_resume);
* xuartps_probe - Platform driver probe
* @pdev: Pointer to the platform device structure
*
- * Returns 0 on success, negative error otherwise
- **/
+ * Return: 0 on success, negative error otherwise
+ */
static int xuartps_probe(struct platform_device *pdev)
{
int rc;
@@ -1437,8 +1426,8 @@ err_out_clk_dis_aper:
* xuartps_remove - called when the platform driver is unregistered
* @pdev: Pointer to the platform device structure
*
- * Returns 0 on success, negative error otherwise
- **/
+ * Return: 0 on success, negative error otherwise
+ */
static int xuartps_remove(struct platform_device *pdev)
{
struct uart_port *port = platform_get_drvdata(pdev);
@@ -1481,8 +1470,8 @@ static struct platform_driver xuartps_platform_driver = {
/**
* xuartps_init - Initial driver registration call
*
- * Returns whether the registration was successful or not
- **/
+ * Return: whether the registration was successful or not
+ */
static int __init xuartps_init(void)
{
int retval = 0;
@@ -1502,7 +1491,7 @@ static int __init xuartps_init(void)
/**
* xuartps_exit - Driver unregistration call
- **/
+ */
static void __exit xuartps_exit(void)
{
/* The order of unregistration is important. Unregister the
--
1.9.1.1.gbb9f595
Print a warning if the clock notifier rejects a clock frequency change
to facilitate debugging (see:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/304329/focus=304379)
Signed-off-by: Soren Brinkmann <[email protected]>
Tested-by: Michal Simek <[email protected]>
---
Changes in v3: None
Changes in v2: None
drivers/tty/serial/xilinx_uartps.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 787a12064fa0..814391038abb 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -429,8 +429,10 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
* frequency.
*/
if (!xuartps_calc_baud_divs(ndata->new_rate, xuartps->baud,
- &bdiv, &cd, &div8))
+ &bdiv, &cd, &div8)) {
+ dev_warn(port->dev, "clock rate change rejected\n");
return NOTIFY_BAD;
+ }
spin_lock_irqsave(&xuartps->port->lock, flags);
--
1.9.1.1.gbb9f595
A comment states, that, according to the data sheet, to enable
interrupts the disable register should be written, but the enable
register could be left untouched. And it suspsects a HW bug requiring
to write both.
Reviewing the data sheet, these statements seem wrong. Just as one would
expect. Writing to the enable/disable register enables/disables
interrupts.
Hence the misleading comment and needless write to the disable register
are removed from the enable sequence.
Signed-off-by: Soren Brinkmann <[email protected]>
Tested-by: Michal Simek <[email protected]>
---
I added a few lines to comment the change and altered the summary line.
In case this causes issues it should show up a little easier as a
candidate to revert.
Changes in v3: None
Changes in v2: None
---
drivers/tty/serial/xilinx_uartps.c | 6 +-----
1 file changed, 1 insertion(+), 5 deletions(-)
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index b182ab8cfd07..f9a2c2fc03c4 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1085,11 +1085,7 @@ static void xuartps_console_write(struct console *co, const char *s,
xuartps_writel(ctrl, XUARTPS_CR_OFFSET);
- /* restore interrupt state, it seems like there may be a h/w bug
- * in that the interrupt enable register should not need to be
- * written based on the data sheet
- */
- xuartps_writel(~imr, XUARTPS_IDR_OFFSET);
+ /* restore interrupt state */
xuartps_writel(imr, XUARTPS_IER_OFFSET);
if (locked)
--
1.9.1.1.gbb9f595
The Zynq UART is Cadence IP and the driver has been renamed accordingly.
Migrate the DT to use the new binding for the UART driver.
Signed-off-by: Soren Brinkmann <[email protected]>
Acked-by: Peter Crosthwaite <[email protected]>
Acked-by: Rob Herring <[email protected]>
Tested-by: Michal Simek <[email protected]>
---
This change depends on 'tty: xuartps: Rebrand driver as Cadence UART',
which introduces the new clock-names.
Changes in v3: None
Changes in v2: None
Signed-off-by: Soren Brinkmann <[email protected]>
---
arch/arm/boot/dts/zynq-7000.dtsi | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi
index 789d0bacc110..d27eb5c21831 100644
--- a/arch/arm/boot/dts/zynq-7000.dtsi
+++ b/arch/arm/boot/dts/zynq-7000.dtsi
@@ -73,19 +73,19 @@
};
uart0: uart@e0000000 {
- compatible = "xlnx,xuartps";
+ compatible = "xlnx,xuartps", "cdns,uart-r1p8";
status = "disabled";
clocks = <&clkc 23>, <&clkc 40>;
- clock-names = "ref_clk", "aper_clk";
+ clock-names = "uart_clk", "pclk";
reg = <0xE0000000 0x1000>;
interrupts = <0 27 4>;
};
uart1: uart@e0001000 {
- compatible = "xlnx,xuartps";
+ compatible = "xlnx,xuartps", "cdns,uart-r1p8";
status = "disabled";
clocks = <&clkc 24>, <&clkc 41>;
- clock-names = "ref_clk", "aper_clk";
+ clock-names = "uart_clk", "pclk";
reg = <0xE0001000 0x1000>;
interrupts = <0 50 4>;
};
--
1.9.1.1.gbb9f595
Zynq's UART is Cadence IP. Make this visible in the prompt in kconfig
and additional comments in the driver.
This also renames functions and symbols, as far as possible without
breaking user space API, to reflect the Cadence origin. This is achieved
through simple search and replace:
- s/XUARTPS/CDNS_UART/g
- s/xuartps/cdns_uart/g
The only exceptions are PORT_XUARTPS and the driver name, which stay as is,
due to their exposure to user space. As well as the - no legacy -
compatibility string 'xlnx,xuartps'
Signed-off-by: Soren Brinkmann <[email protected]>
Tested-by: Michal Simek <[email protected]>
---
Changes in v3:
- apply renaming to code that has been brought in with patches added in v3
- revert legacy compat string back to xlnx,xuartps (it was an
unintended victim of the search and replace)
Changes in v2: None
---
drivers/tty/serial/Kconfig | 9 +-
drivers/tty/serial/xilinx_uartps.c | 908 +++++++++++++++++++------------------
include/uapi/linux/serial_core.h | 2 +-
3 files changed, 471 insertions(+), 448 deletions(-)
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 2577d67bacb2..011f80c7da3b 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1368,18 +1368,19 @@ config SERIAL_MXS_AUART_CONSOLE
Enable a MXS AUART port to be the system console.
config SERIAL_XILINX_PS_UART
- tristate "Xilinx PS UART support"
+ tristate "Cadence (Xilinx Zynq) UART support"
depends on OF
select SERIAL_CORE
help
- This driver supports the Xilinx PS UART port.
+ This driver supports the Cadence UART. It is found e.g. in Xilinx
+ Zynq.
config SERIAL_XILINX_PS_UART_CONSOLE
- bool "Xilinx PS UART console support"
+ bool "Cadence UART console support"
depends on SERIAL_XILINX_PS_UART=y
select SERIAL_CORE_CONSOLE
help
- Enable a Xilinx PS UART port to be the system console.
+ Enable a Cadence UART port to be the system console.
config SERIAL_AR933X
tristate "AR933X serial port support"
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f9a2c2fc03c4..8809775e2ba3 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1,5 +1,5 @@
/*
- * Xilinx PS UART driver
+ * Cadence UART driver (found in Xilinx Zynq)
*
* 2011 - 2014 (C) Xilinx Inc.
*
@@ -8,6 +8,10 @@
* License as published by the Free Software Foundation;
* either version 2 of the License, or (at your option) any
* later version.
+ *
+ * This driver has originally been pushed by Xilinx using a Zynq-branding. This
+ * still shows in the naming of this file, the kconfig symbols and some symbols
+ * in the code.
*/
#if defined(CONFIG_SERIAL_XILINX_PS_UART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
@@ -27,16 +31,16 @@
#include <linux/of.h>
#include <linux/module.h>
-#define XUARTPS_TTY_NAME "ttyPS"
-#define XUARTPS_NAME "xuartps"
-#define XUARTPS_MAJOR 0 /* use dynamic node allocation */
-#define XUARTPS_MINOR 0 /* works best with devtmpfs */
-#define XUARTPS_NR_PORTS 2
-#define XUARTPS_FIFO_SIZE 64 /* FIFO size */
-#define XUARTPS_REGISTER_SPACE 0xFFF
+#define CDNS_UART_TTY_NAME "ttyPS"
+#define CDNS_UART_NAME "xuartps"
+#define CDNS_UART_MAJOR 0 /* use dynamic node allocation */
+#define CDNS_UART_MINOR 0 /* works best with devtmpfs */
+#define CDNS_UART_NR_PORTS 2
+#define CDNS_UART_FIFO_SIZE 64 /* FIFO size */
+#define CDNS_UART_REGISTER_SPACE 0xFFF
-#define xuartps_readl(offset) ioread32(port->membase + offset)
-#define xuartps_writel(val, offset) iowrite32(val, port->membase + offset)
+#define cdns_uart_readl(offset) ioread32(port->membase + offset)
+#define cdns_uart_writel(val, offset) iowrite32(val, port->membase + offset)
/* Rx Trigger level */
static int rx_trigger_level = 56;
@@ -49,35 +53,35 @@ module_param(rx_timeout, uint, S_IRUGO);
MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
/* Register offsets for the UART. */
-#define XUARTPS_CR_OFFSET 0x00 /* Control Register */
-#define XUARTPS_MR_OFFSET 0x04 /* Mode Register */
-#define XUARTPS_IER_OFFSET 0x08 /* Interrupt Enable */
-#define XUARTPS_IDR_OFFSET 0x0C /* Interrupt Disable */
-#define XUARTPS_IMR_OFFSET 0x10 /* Interrupt Mask */
-#define XUARTPS_ISR_OFFSET 0x14 /* Interrupt Status */
-#define XUARTPS_BAUDGEN_OFFSET 0x18 /* Baud Rate Generator */
-#define XUARTPS_RXTOUT_OFFSET 0x1C /* RX Timeout */
-#define XUARTPS_RXWM_OFFSET 0x20 /* RX FIFO Trigger Level */
-#define XUARTPS_MODEMCR_OFFSET 0x24 /* Modem Control */
-#define XUARTPS_MODEMSR_OFFSET 0x28 /* Modem Status */
-#define XUARTPS_SR_OFFSET 0x2C /* Channel Status */
-#define XUARTPS_FIFO_OFFSET 0x30 /* FIFO */
-#define XUARTPS_BAUDDIV_OFFSET 0x34 /* Baud Rate Divider */
-#define XUARTPS_FLOWDEL_OFFSET 0x38 /* Flow Delay */
-#define XUARTPS_IRRX_PWIDTH_OFFSET 0x3C /* IR Minimum Received Pulse Width */
-#define XUARTPS_IRTX_PWIDTH_OFFSET 0x40 /* IR Transmitted pulse Width */
-#define XUARTPS_TXWM_OFFSET 0x44 /* TX FIFO Trigger Level */
+#define CDNS_UART_CR_OFFSET 0x00 /* Control Register */
+#define CDNS_UART_MR_OFFSET 0x04 /* Mode Register */
+#define CDNS_UART_IER_OFFSET 0x08 /* Interrupt Enable */
+#define CDNS_UART_IDR_OFFSET 0x0C /* Interrupt Disable */
+#define CDNS_UART_IMR_OFFSET 0x10 /* Interrupt Mask */
+#define CDNS_UART_ISR_OFFSET 0x14 /* Interrupt Status */
+#define CDNS_UART_BAUDGEN_OFFSET 0x18 /* Baud Rate Generator */
+#define CDNS_UART_RXTOUT_OFFSET 0x1C /* RX Timeout */
+#define CDNS_UART_RXWM_OFFSET 0x20 /* RX FIFO Trigger Level */
+#define CDNS_UART_MODEMCR_OFFSET 0x24 /* Modem Control */
+#define CDNS_UART_MODEMSR_OFFSET 0x28 /* Modem Status */
+#define CDNS_UART_SR_OFFSET 0x2C /* Channel Status */
+#define CDNS_UART_FIFO_OFFSET 0x30 /* FIFO */
+#define CDNS_UART_BAUDDIV_OFFSET 0x34 /* Baud Rate Divider */
+#define CDNS_UART_FLOWDEL_OFFSET 0x38 /* Flow Delay */
+#define CDNS_UART_IRRX_PWIDTH_OFFSET 0x3C /* IR Min Received Pulse Width */
+#define CDNS_UART_IRTX_PWIDTH_OFFSET 0x40 /* IR Transmitted pulse Width */
+#define CDNS_UART_TXWM_OFFSET 0x44 /* TX FIFO Trigger Level */
/* Control Register Bit Definitions */
-#define XUARTPS_CR_STOPBRK 0x00000100 /* Stop TX break */
-#define XUARTPS_CR_STARTBRK 0x00000080 /* Set TX break */
-#define XUARTPS_CR_TX_DIS 0x00000020 /* TX disabled. */
-#define XUARTPS_CR_TX_EN 0x00000010 /* TX enabled */
-#define XUARTPS_CR_RX_DIS 0x00000008 /* RX disabled. */
-#define XUARTPS_CR_RX_EN 0x00000004 /* RX enabled */
-#define XUARTPS_CR_TXRST 0x00000002 /* TX logic reset */
-#define XUARTPS_CR_RXRST 0x00000001 /* RX logic reset */
-#define XUARTPS_CR_RST_TO 0x00000040 /* Restart Timeout Counter */
+#define CDNS_UART_CR_STOPBRK 0x00000100 /* Stop TX break */
+#define CDNS_UART_CR_STARTBRK 0x00000080 /* Set TX break */
+#define CDNS_UART_CR_TX_DIS 0x00000020 /* TX disabled. */
+#define CDNS_UART_CR_TX_EN 0x00000010 /* TX enabled */
+#define CDNS_UART_CR_RX_DIS 0x00000008 /* RX disabled. */
+#define CDNS_UART_CR_RX_EN 0x00000004 /* RX enabled */
+#define CDNS_UART_CR_TXRST 0x00000002 /* TX logic reset */
+#define CDNS_UART_CR_RXRST 0x00000001 /* RX logic reset */
+#define CDNS_UART_CR_RST_TO 0x00000040 /* Restart Timeout Counter */
/*
* Mode Register:
@@ -85,22 +89,22 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
* format. If this register is modified during transmission or reception,
* data validity cannot be guaranteed.
*/
-#define XUARTPS_MR_CLKSEL 0x00000001 /* Pre-scalar selection */
-#define XUARTPS_MR_CHMODE_L_LOOP 0x00000200 /* Local loop back mode */
-#define XUARTPS_MR_CHMODE_NORM 0x00000000 /* Normal mode */
+#define CDNS_UART_MR_CLKSEL 0x00000001 /* Pre-scalar selection */
+#define CDNS_UART_MR_CHMODE_L_LOOP 0x00000200 /* Local loop back mode */
+#define CDNS_UART_MR_CHMODE_NORM 0x00000000 /* Normal mode */
-#define XUARTPS_MR_STOPMODE_2_BIT 0x00000080 /* 2 stop bits */
-#define XUARTPS_MR_STOPMODE_1_BIT 0x00000000 /* 1 stop bit */
+#define CDNS_UART_MR_STOPMODE_2_BIT 0x00000080 /* 2 stop bits */
+#define CDNS_UART_MR_STOPMODE_1_BIT 0x00000000 /* 1 stop bit */
-#define XUARTPS_MR_PARITY_NONE 0x00000020 /* No parity mode */
-#define XUARTPS_MR_PARITY_MARK 0x00000018 /* Mark parity mode */
-#define XUARTPS_MR_PARITY_SPACE 0x00000010 /* Space parity mode */
-#define XUARTPS_MR_PARITY_ODD 0x00000008 /* Odd parity mode */
-#define XUARTPS_MR_PARITY_EVEN 0x00000000 /* Even parity mode */
+#define CDNS_UART_MR_PARITY_NONE 0x00000020 /* No parity mode */
+#define CDNS_UART_MR_PARITY_MARK 0x00000018 /* Mark parity mode */
+#define CDNS_UART_MR_PARITY_SPACE 0x00000010 /* Space parity mode */
+#define CDNS_UART_MR_PARITY_ODD 0x00000008 /* Odd parity mode */
+#define CDNS_UART_MR_PARITY_EVEN 0x00000000 /* Even parity mode */
-#define XUARTPS_MR_CHARLEN_6_BIT 0x00000006 /* 6 bits data */
-#define XUARTPS_MR_CHARLEN_7_BIT 0x00000004 /* 7 bits data */
-#define XUARTPS_MR_CHARLEN_8_BIT 0x00000000 /* 8 bits data */
+#define CDNS_UART_MR_CHARLEN_6_BIT 0x00000006 /* 6 bits data */
+#define CDNS_UART_MR_CHARLEN_7_BIT 0x00000004 /* 7 bits data */
+#define CDNS_UART_MR_CHARLEN_8_BIT 0x00000000 /* 8 bits data */
/*
* Interrupt Registers:
@@ -113,20 +117,20 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
* Reading either IER or IDR returns 0x00.
* All four registers have the same bit definitions.
*/
-#define XUARTPS_IXR_TOUT 0x00000100 /* RX Timeout error interrupt */
-#define XUARTPS_IXR_PARITY 0x00000080 /* Parity error interrupt */
-#define XUARTPS_IXR_FRAMING 0x00000040 /* Framing error interrupt */
-#define XUARTPS_IXR_OVERRUN 0x00000020 /* Overrun error interrupt */
-#define XUARTPS_IXR_TXFULL 0x00000010 /* TX FIFO Full interrupt */
-#define XUARTPS_IXR_TXEMPTY 0x00000008 /* TX FIFO empty interrupt */
-#define XUARTPS_ISR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt */
-#define XUARTPS_IXR_RXTRIG 0x00000001 /* RX FIFO trigger interrupt */
-#define XUARTPS_IXR_RXFULL 0x00000004 /* RX FIFO full interrupt. */
-#define XUARTPS_IXR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt. */
-#define XUARTPS_IXR_MASK 0x00001FFF /* Valid bit mask */
+#define CDNS_UART_IXR_TOUT 0x00000100 /* RX Timeout error interrupt */
+#define CDNS_UART_IXR_PARITY 0x00000080 /* Parity error interrupt */
+#define CDNS_UART_IXR_FRAMING 0x00000040 /* Framing error interrupt */
+#define CDNS_UART_IXR_OVERRUN 0x00000020 /* Overrun error interrupt */
+#define CDNS_UART_IXR_TXFULL 0x00000010 /* TX FIFO Full interrupt */
+#define CDNS_UART_IXR_TXEMPTY 0x00000008 /* TX FIFO empty interrupt */
+#define CDNS_UART_ISR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt */
+#define CDNS_UART_IXR_RXTRIG 0x00000001 /* RX FIFO trigger interrupt */
+#define CDNS_UART_IXR_RXFULL 0x00000004 /* RX FIFO full interrupt. */
+#define CDNS_UART_IXR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt. */
+#define CDNS_UART_IXR_MASK 0x00001FFF /* Valid bit mask */
/* Goes in read_status_mask for break detection as the HW doesn't do it*/
-#define XUARTPS_IXR_BRK 0x80000000
+#define CDNS_UART_IXR_BRK 0x80000000
/*
* Channel Status Register:
@@ -134,41 +138,42 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
* to monitor the status of bits in the channel interrupt status register,
* even if these are masked out by the interrupt mask register.
*/
-#define XUARTPS_SR_RXEMPTY 0x00000002 /* RX FIFO empty */
-#define XUARTPS_SR_TXEMPTY 0x00000008 /* TX FIFO empty */
-#define XUARTPS_SR_TXFULL 0x00000010 /* TX FIFO full */
-#define XUARTPS_SR_RXTRIG 0x00000001 /* Rx Trigger */
+#define CDNS_UART_SR_RXEMPTY 0x00000002 /* RX FIFO empty */
+#define CDNS_UART_SR_TXEMPTY 0x00000008 /* TX FIFO empty */
+#define CDNS_UART_SR_TXFULL 0x00000010 /* TX FIFO full */
+#define CDNS_UART_SR_RXTRIG 0x00000001 /* Rx Trigger */
/* baud dividers min/max values */
-#define XUARTPS_BDIV_MIN 4
-#define XUARTPS_BDIV_MAX 255
-#define XUARTPS_CD_MAX 65535
+#define CDNS_UART_BDIV_MIN 4
+#define CDNS_UART_BDIV_MAX 255
+#define CDNS_UART_CD_MAX 65535
/**
- * struct xuartps - device data
+ * struct cdns_uart - device data
* @port: Pointer to the UART port
- * @refclk: Reference clock
- * @aperclk: APB clock
+ * @uartclk: Reference clock
+ * @pclk: APB clock
* @baud: Current baud rate
* @clk_rate_change_nb: Notifier block for clock changes
*/
-struct xuartps {
+struct cdns_uart {
struct uart_port *port;
- struct clk *refclk;
- struct clk *aperclk;
+ struct clk *uartclk;
+ struct clk *pclk;
unsigned int baud;
struct notifier_block clk_rate_change_nb;
};
-#define to_xuartps(_nb) container_of(_nb, struct xuartps, clk_rate_change_nb);
+#define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \
+ clk_rate_change_nb);
/**
- * xuartps_isr - Interrupt handler
+ * cdns_uart_isr - Interrupt handler
* @irq: Irq number
* @dev_id: Id of the port
*
* Return: IRQHANDLED
*/
-static irqreturn_t xuartps_isr(int irq, void *dev_id)
+static irqreturn_t cdns_uart_isr(int irq, void *dev_id)
{
struct uart_port *port = (struct uart_port *)dev_id;
unsigned long flags;
@@ -181,42 +186,42 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
/* Read the interrupt status register to determine which
* interrupt(s) is/are active.
*/
- isrstatus = xuartps_readl(XUARTPS_ISR_OFFSET);
+ isrstatus = cdns_uart_readl(CDNS_UART_ISR_OFFSET);
/*
* There is no hardware break detection, so we interpret framing
* error with all-zeros data as a break sequence. Most of the time,
* there's another non-zero byte at the end of the sequence.
*/
- if (isrstatus & XUARTPS_IXR_FRAMING) {
- while (!(xuartps_readl(XUARTPS_SR_OFFSET) &
- XUARTPS_SR_RXEMPTY)) {
- if (!xuartps_readl(XUARTPS_FIFO_OFFSET)) {
- port->read_status_mask |= XUARTPS_IXR_BRK;
- isrstatus &= ~XUARTPS_IXR_FRAMING;
+ if (isrstatus & CDNS_UART_IXR_FRAMING) {
+ while (!(cdns_uart_readl(CDNS_UART_SR_OFFSET) &
+ CDNS_UART_SR_RXEMPTY)) {
+ if (!cdns_uart_readl(CDNS_UART_FIFO_OFFSET)) {
+ port->read_status_mask |= CDNS_UART_IXR_BRK;
+ isrstatus &= ~CDNS_UART_IXR_FRAMING;
}
}
- xuartps_writel(XUARTPS_IXR_FRAMING, XUARTPS_ISR_OFFSET);
+ cdns_uart_writel(CDNS_UART_IXR_FRAMING, CDNS_UART_ISR_OFFSET);
}
/* drop byte with parity error if IGNPAR specified */
- if (isrstatus & port->ignore_status_mask & XUARTPS_IXR_PARITY)
- isrstatus &= ~(XUARTPS_IXR_RXTRIG | XUARTPS_IXR_TOUT);
+ if (isrstatus & port->ignore_status_mask & CDNS_UART_IXR_PARITY)
+ isrstatus &= ~(CDNS_UART_IXR_RXTRIG | CDNS_UART_IXR_TOUT);
isrstatus &= port->read_status_mask;
isrstatus &= ~port->ignore_status_mask;
- if ((isrstatus & XUARTPS_IXR_TOUT) ||
- (isrstatus & XUARTPS_IXR_RXTRIG)) {
+ if ((isrstatus & CDNS_UART_IXR_TOUT) ||
+ (isrstatus & CDNS_UART_IXR_RXTRIG)) {
/* Receive Timeout Interrupt */
- while ((xuartps_readl(XUARTPS_SR_OFFSET) &
- XUARTPS_SR_RXEMPTY) != XUARTPS_SR_RXEMPTY) {
- data = xuartps_readl(XUARTPS_FIFO_OFFSET);
+ while ((cdns_uart_readl(CDNS_UART_SR_OFFSET) &
+ CDNS_UART_SR_RXEMPTY) != CDNS_UART_SR_RXEMPTY) {
+ data = cdns_uart_readl(CDNS_UART_FIFO_OFFSET);
/* Non-NULL byte after BREAK is garbage (99%) */
if (data && (port->read_status_mask &
- XUARTPS_IXR_BRK)) {
- port->read_status_mask &= ~XUARTPS_IXR_BRK;
+ CDNS_UART_IXR_BRK)) {
+ port->read_status_mask &= ~CDNS_UART_IXR_BRK;
port->icount.brk++;
if (uart_handle_break(port))
continue;
@@ -240,17 +245,17 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
port->icount.rx++;
- if (isrstatus & XUARTPS_IXR_PARITY) {
+ if (isrstatus & CDNS_UART_IXR_PARITY) {
port->icount.parity++;
status = TTY_PARITY;
- } else if (isrstatus & XUARTPS_IXR_FRAMING) {
+ } else if (isrstatus & CDNS_UART_IXR_FRAMING) {
port->icount.frame++;
status = TTY_FRAME;
- } else if (isrstatus & XUARTPS_IXR_OVERRUN) {
+ } else if (isrstatus & CDNS_UART_IXR_OVERRUN) {
port->icount.overrun++;
}
- uart_insert_char(port, isrstatus, XUARTPS_IXR_OVERRUN,
+ uart_insert_char(port, isrstatus, CDNS_UART_IXR_OVERRUN,
data, status);
}
spin_unlock(&port->lock);
@@ -259,10 +264,10 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
}
/* Dispatch an appropriate handler */
- if ((isrstatus & XUARTPS_IXR_TXEMPTY) == XUARTPS_IXR_TXEMPTY) {
+ if ((isrstatus & CDNS_UART_IXR_TXEMPTY) == CDNS_UART_IXR_TXEMPTY) {
if (uart_circ_empty(&port->state->xmit)) {
- xuartps_writel(XUARTPS_IXR_TXEMPTY,
- XUARTPS_IDR_OFFSET);
+ cdns_uart_writel(CDNS_UART_IXR_TXEMPTY,
+ CDNS_UART_IDR_OFFSET);
} else {
numbytes = port->fifosize;
/* Break if no more data available in the UART buffer */
@@ -270,12 +275,12 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
if (uart_circ_empty(&port->state->xmit))
break;
/* Get the data from the UART circular buffer
- * and write it to the xuartps's TX_FIFO
+ * and write it to the cdns_uart's TX_FIFO
* register.
*/
- xuartps_writel(
+ cdns_uart_writel(
port->state->xmit.buf[port->state->xmit.
- tail], XUARTPS_FIFO_OFFSET);
+ tail], CDNS_UART_FIFO_OFFSET);
port->icount.tx++;
@@ -293,7 +298,7 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
}
}
- xuartps_writel(isrstatus, XUARTPS_ISR_OFFSET);
+ cdns_uart_writel(isrstatus, CDNS_UART_ISR_OFFSET);
/* be sure to release the lock and tty before leaving */
spin_unlock_irqrestore(&port->lock, flags);
@@ -302,7 +307,7 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
}
/**
- * xuartps_calc_baud_divs - Calculate baud rate divisors
+ * cdns_uart_calc_baud_divs - Calculate baud rate divisors
* @clk: UART module input clock
* @baud: Desired baud rate
* @rbdiv: BDIV value (return value)
@@ -321,8 +326,8 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
* baud rate generate register
* baud rate clock divisor register
*/
-static unsigned int xuartps_calc_baud_divs(unsigned int clk, unsigned int baud,
- u32 *rbdiv, u32 *rcd, int *div8)
+static unsigned int cdns_uart_calc_baud_divs(unsigned int clk,
+ unsigned int baud, u32 *rbdiv, u32 *rcd, int *div8)
{
u32 cd, bdiv;
unsigned int calc_baud;
@@ -330,16 +335,16 @@ static unsigned int xuartps_calc_baud_divs(unsigned int clk, unsigned int baud,
unsigned int bauderror;
unsigned int besterror = ~0;
- if (baud < clk / ((XUARTPS_BDIV_MAX + 1) * XUARTPS_CD_MAX)) {
+ if (baud < clk / ((CDNS_UART_BDIV_MAX + 1) * CDNS_UART_CD_MAX)) {
*div8 = 1;
clk /= 8;
} else {
*div8 = 0;
}
- for (bdiv = XUARTPS_BDIV_MIN; bdiv <= XUARTPS_BDIV_MAX; bdiv++) {
+ for (bdiv = CDNS_UART_BDIV_MIN; bdiv <= CDNS_UART_BDIV_MAX; bdiv++) {
cd = DIV_ROUND_CLOSEST(clk, baud * (bdiv + 1));
- if (cd < 1 || cd > XUARTPS_CD_MAX)
+ if (cd < 1 || cd > CDNS_UART_CD_MAX)
continue;
calc_baud = clk / (cd * (bdiv + 1));
@@ -364,47 +369,47 @@ static unsigned int xuartps_calc_baud_divs(unsigned int clk, unsigned int baud,
}
/**
- * xuartps_set_baud_rate - Calculate and set the baud rate
+ * cdns_uart_set_baud_rate - Calculate and set the baud rate
* @port: Handle to the uart port structure
* @baud: Baud rate to set
* Return: baud rate, requested baud when possible, or actual baud when there
* was too much error, zero if no valid divisors are found.
*/
-static unsigned int xuartps_set_baud_rate(struct uart_port *port,
+static unsigned int cdns_uart_set_baud_rate(struct uart_port *port,
unsigned int baud)
{
unsigned int calc_baud;
u32 cd = 0, bdiv = 0;
u32 mreg;
int div8;
- struct xuartps *xuartps = port->private_data;
+ struct cdns_uart *cdns_uart = port->private_data;
- calc_baud = xuartps_calc_baud_divs(port->uartclk, baud, &bdiv, &cd,
+ calc_baud = cdns_uart_calc_baud_divs(port->uartclk, baud, &bdiv, &cd,
&div8);
/* Write new divisors to hardware */
- mreg = xuartps_readl(XUARTPS_MR_OFFSET);
+ mreg = cdns_uart_readl(CDNS_UART_MR_OFFSET);
if (div8)
- mreg |= XUARTPS_MR_CLKSEL;
+ mreg |= CDNS_UART_MR_CLKSEL;
else
- mreg &= ~XUARTPS_MR_CLKSEL;
- xuartps_writel(mreg, XUARTPS_MR_OFFSET);
- xuartps_writel(cd, XUARTPS_BAUDGEN_OFFSET);
- xuartps_writel(bdiv, XUARTPS_BAUDDIV_OFFSET);
- xuartps->baud = baud;
+ mreg &= ~CDNS_UART_MR_CLKSEL;
+ cdns_uart_writel(mreg, CDNS_UART_MR_OFFSET);
+ cdns_uart_writel(cd, CDNS_UART_BAUDGEN_OFFSET);
+ cdns_uart_writel(bdiv, CDNS_UART_BAUDDIV_OFFSET);
+ cdns_uart->baud = baud;
return calc_baud;
}
#ifdef CONFIG_COMMON_CLK
/**
- * xuartps_clk_notitifer_cb - Clock notifier callback
+ * cdns_uart_clk_notitifer_cb - Clock notifier callback
* @nb: Notifier block
* @event: Notify event
* @data: Notifier data
* Return: NOTIFY_OK or NOTIFY_DONE on success, NOTIFY_BAD on error.
*/
-static int xuartps_clk_notifier_cb(struct notifier_block *nb,
+static int cdns_uart_clk_notifier_cb(struct notifier_block *nb,
unsigned long event, void *data)
{
u32 ctrl_reg;
@@ -412,9 +417,9 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
int locked = 0;
struct clk_notifier_data *ndata = data;
unsigned long flags = 0;
- struct xuartps *xuartps = to_xuartps(nb);
+ struct cdns_uart *cdns_uart = to_cdns_uart(nb);
- port = xuartps->port;
+ port = cdns_uart->port;
if (port->suspended)
return NOTIFY_OK;
@@ -428,20 +433,20 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
* Find out if current baud-rate can be achieved with new clock
* frequency.
*/
- if (!xuartps_calc_baud_divs(ndata->new_rate, xuartps->baud,
+ if (!cdns_uart_calc_baud_divs(ndata->new_rate, cdns_uart->baud,
&bdiv, &cd, &div8)) {
dev_warn(port->dev, "clock rate change rejected\n");
return NOTIFY_BAD;
}
- spin_lock_irqsave(&xuartps->port->lock, flags);
+ spin_lock_irqsave(&cdns_uart->port->lock, flags);
/* Disable the TX and RX to set baud rate */
- ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- ctrl_reg |= XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS;
- xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
+ ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
+ cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
- spin_unlock_irqrestore(&xuartps->port->lock, flags);
+ spin_unlock_irqrestore(&cdns_uart->port->lock, flags);
return NOTIFY_OK;
}
@@ -451,25 +456,25 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
* frequency.
*/
- spin_lock_irqsave(&xuartps->port->lock, flags);
+ spin_lock_irqsave(&cdns_uart->port->lock, flags);
locked = 1;
port->uartclk = ndata->new_rate;
- xuartps->baud = xuartps_set_baud_rate(xuartps->port,
- xuartps->baud);
+ cdns_uart->baud = cdns_uart_set_baud_rate(cdns_uart->port,
+ cdns_uart->baud);
/* fall through */
case ABORT_RATE_CHANGE:
if (!locked)
- spin_lock_irqsave(&xuartps->port->lock, flags);
+ spin_lock_irqsave(&cdns_uart->port->lock, flags);
/* Set TX/RX Reset */
- ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- ctrl_reg |= XUARTPS_CR_TXRST | XUARTPS_CR_RXRST;
- xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
+ ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
+ cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
- while (xuartps_readl(XUARTPS_CR_OFFSET) &
- (XUARTPS_CR_TXRST | XUARTPS_CR_RXRST))
+ while (cdns_uart_readl(CDNS_UART_CR_OFFSET) &
+ (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
cpu_relax();
/*
@@ -477,13 +482,13 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
* enable bit and RX enable bit to enable the transmitter and
* receiver.
*/
- xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
- ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- ctrl_reg &= ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS);
- ctrl_reg |= XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN;
- xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
+ cdns_uart_writel(rx_timeout, CDNS_UART_RXTOUT_OFFSET);
+ ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
+ ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
+ cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
- spin_unlock_irqrestore(&xuartps->port->lock, flags);
+ spin_unlock_irqrestore(&cdns_uart->port->lock, flags);
return NOTIFY_OK;
default:
@@ -493,35 +498,35 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
#endif
/**
- * xuartps_start_tx - Start transmitting bytes
+ * cdns_uart_start_tx - Start transmitting bytes
* @port: Handle to the uart port structure
*/
-static void xuartps_start_tx(struct uart_port *port)
+static void cdns_uart_start_tx(struct uart_port *port)
{
unsigned int status, numbytes = port->fifosize;
if (uart_circ_empty(&port->state->xmit) || uart_tx_stopped(port))
return;
- status = xuartps_readl(XUARTPS_CR_OFFSET);
+ status = cdns_uart_readl(CDNS_UART_CR_OFFSET);
/* Set the TX enable bit and clear the TX disable bit to enable the
* transmitter.
*/
- xuartps_writel((status & ~XUARTPS_CR_TX_DIS) | XUARTPS_CR_TX_EN,
- XUARTPS_CR_OFFSET);
+ cdns_uart_writel((status & ~CDNS_UART_CR_TX_DIS) | CDNS_UART_CR_TX_EN,
+ CDNS_UART_CR_OFFSET);
- while (numbytes-- && ((xuartps_readl(XUARTPS_SR_OFFSET) &
- XUARTPS_SR_TXFULL)) != XUARTPS_SR_TXFULL) {
+ while (numbytes-- && ((cdns_uart_readl(CDNS_UART_SR_OFFSET) &
+ CDNS_UART_SR_TXFULL)) != CDNS_UART_SR_TXFULL) {
/* Break if no more data available in the UART buffer */
if (uart_circ_empty(&port->state->xmit))
break;
/* Get the data from the UART circular buffer and
- * write it to the xuartps's TX_FIFO register.
+ * write it to the cdns_uart's TX_FIFO register.
*/
- xuartps_writel(
+ cdns_uart_writel(
port->state->xmit.buf[port->state->xmit.tail],
- XUARTPS_FIFO_OFFSET);
+ CDNS_UART_FIFO_OFFSET);
port->icount.tx++;
/* Adjust the tail of the UART buffer and wrap
@@ -530,90 +535,90 @@ static void xuartps_start_tx(struct uart_port *port)
port->state->xmit.tail = (port->state->xmit.tail + 1) &
(UART_XMIT_SIZE - 1);
}
- xuartps_writel(XUARTPS_IXR_TXEMPTY, XUARTPS_ISR_OFFSET);
+ cdns_uart_writel(CDNS_UART_IXR_TXEMPTY, CDNS_UART_ISR_OFFSET);
/* Enable the TX Empty interrupt */
- xuartps_writel(XUARTPS_IXR_TXEMPTY, XUARTPS_IER_OFFSET);
+ cdns_uart_writel(CDNS_UART_IXR_TXEMPTY, CDNS_UART_IER_OFFSET);
if (uart_circ_chars_pending(&port->state->xmit) < WAKEUP_CHARS)
uart_write_wakeup(port);
}
/**
- * xuartps_stop_tx - Stop TX
+ * cdns_uart_stop_tx - Stop TX
* @port: Handle to the uart port structure
*/
-static void xuartps_stop_tx(struct uart_port *port)
+static void cdns_uart_stop_tx(struct uart_port *port)
{
unsigned int regval;
- regval = xuartps_readl(XUARTPS_CR_OFFSET);
- regval |= XUARTPS_CR_TX_DIS;
+ regval = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ regval |= CDNS_UART_CR_TX_DIS;
/* Disable the transmitter */
- xuartps_writel(regval, XUARTPS_CR_OFFSET);
+ cdns_uart_writel(regval, CDNS_UART_CR_OFFSET);
}
/**
- * xuartps_stop_rx - Stop RX
+ * cdns_uart_stop_rx - Stop RX
* @port: Handle to the uart port structure
*/
-static void xuartps_stop_rx(struct uart_port *port)
+static void cdns_uart_stop_rx(struct uart_port *port)
{
unsigned int regval;
- regval = xuartps_readl(XUARTPS_CR_OFFSET);
- regval |= XUARTPS_CR_RX_DIS;
+ regval = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ regval |= CDNS_UART_CR_RX_DIS;
/* Disable the receiver */
- xuartps_writel(regval, XUARTPS_CR_OFFSET);
+ cdns_uart_writel(regval, CDNS_UART_CR_OFFSET);
}
/**
- * xuartps_tx_empty - Check whether TX is empty
+ * cdns_uart_tx_empty - Check whether TX is empty
* @port: Handle to the uart port structure
*
* Return: TIOCSER_TEMT on success, 0 otherwise
*/
-static unsigned int xuartps_tx_empty(struct uart_port *port)
+static unsigned int cdns_uart_tx_empty(struct uart_port *port)
{
unsigned int status;
- status = xuartps_readl(XUARTPS_ISR_OFFSET) & XUARTPS_IXR_TXEMPTY;
+ status = cdns_uart_readl(CDNS_UART_ISR_OFFSET) & CDNS_UART_IXR_TXEMPTY;
return status ? TIOCSER_TEMT : 0;
}
/**
- * xuartps_break_ctl - Based on the input ctl we have to start or stop
+ * cdns_uart_break_ctl - Based on the input ctl we have to start or stop
* transmitting char breaks
* @port: Handle to the uart port structure
* @ctl: Value based on which start or stop decision is taken
*/
-static void xuartps_break_ctl(struct uart_port *port, int ctl)
+static void cdns_uart_break_ctl(struct uart_port *port, int ctl)
{
unsigned int status;
unsigned long flags;
spin_lock_irqsave(&port->lock, flags);
- status = xuartps_readl(XUARTPS_CR_OFFSET);
+ status = cdns_uart_readl(CDNS_UART_CR_OFFSET);
if (ctl == -1)
- xuartps_writel(XUARTPS_CR_STARTBRK | status,
- XUARTPS_CR_OFFSET);
+ cdns_uart_writel(CDNS_UART_CR_STARTBRK | status,
+ CDNS_UART_CR_OFFSET);
else {
- if ((status & XUARTPS_CR_STOPBRK) == 0)
- xuartps_writel(XUARTPS_CR_STOPBRK | status,
- XUARTPS_CR_OFFSET);
+ if ((status & CDNS_UART_CR_STOPBRK) == 0)
+ cdns_uart_writel(CDNS_UART_CR_STOPBRK | status,
+ CDNS_UART_CR_OFFSET);
}
spin_unlock_irqrestore(&port->lock, flags);
}
/**
- * xuartps_set_termios - termios operations, handling data length, parity,
+ * cdns_uart_set_termios - termios operations, handling data length, parity,
* stop bits, flow control, baud rate
* @port: Handle to the uart port structure
* @termios: Handle to the input termios structure
* @old: Values of the previously saved termios structure
*/
-static void xuartps_set_termios(struct uart_port *port,
+static void cdns_uart_set_termios(struct uart_port *port,
struct ktermios *termios, struct ktermios *old)
{
unsigned int cval = 0;
@@ -624,25 +629,26 @@ static void xuartps_set_termios(struct uart_port *port,
spin_lock_irqsave(&port->lock, flags);
/* Empty the receive FIFO 1st before making changes */
- while ((xuartps_readl(XUARTPS_SR_OFFSET) &
- XUARTPS_SR_RXEMPTY) != XUARTPS_SR_RXEMPTY) {
- xuartps_readl(XUARTPS_FIFO_OFFSET);
+ while ((cdns_uart_readl(CDNS_UART_SR_OFFSET) &
+ CDNS_UART_SR_RXEMPTY) != CDNS_UART_SR_RXEMPTY) {
+ cdns_uart_readl(CDNS_UART_FIFO_OFFSET);
}
/* Disable the TX and RX to set baud rate */
- ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- ctrl_reg |= XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS;
- xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
+ ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
+ cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
/*
* Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk
* min and max baud should be calculated here based on port->uartclk.
* this way we get a valid baud and can safely call set_baud()
*/
- minbaud = port->uartclk / ((XUARTPS_BDIV_MAX + 1) * XUARTPS_CD_MAX * 8);
- maxbaud = port->uartclk / (XUARTPS_BDIV_MIN + 1);
+ minbaud = port->uartclk /
+ ((CDNS_UART_BDIV_MAX + 1) * CDNS_UART_CD_MAX * 8);
+ maxbaud = port->uartclk / (CDNS_UART_BDIV_MIN + 1);
baud = uart_get_baud_rate(port, termios, old, minbaud, maxbaud);
- baud = xuartps_set_baud_rate(port, baud);
+ baud = cdns_uart_set_baud_rate(port, baud);
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
@@ -650,52 +656,52 @@ static void xuartps_set_termios(struct uart_port *port,
uart_update_timeout(port, termios->c_cflag, baud);
/* Set TX/RX Reset */
- ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- ctrl_reg |= XUARTPS_CR_TXRST | XUARTPS_CR_RXRST;
- xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
+ ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
+ cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
*/
- ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- ctrl_reg &= ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS);
- ctrl_reg |= XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN;
- xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
+ ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
+ ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
+ cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
- xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
+ cdns_uart_writel(rx_timeout, CDNS_UART_RXTOUT_OFFSET);
- port->read_status_mask = XUARTPS_IXR_TXEMPTY | XUARTPS_IXR_RXTRIG |
- XUARTPS_IXR_OVERRUN | XUARTPS_IXR_TOUT;
+ port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
+ CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
port->ignore_status_mask = 0;
if (termios->c_iflag & INPCK)
- port->read_status_mask |= XUARTPS_IXR_PARITY |
- XUARTPS_IXR_FRAMING;
+ port->read_status_mask |= CDNS_UART_IXR_PARITY |
+ CDNS_UART_IXR_FRAMING;
if (termios->c_iflag & IGNPAR)
- port->ignore_status_mask |= XUARTPS_IXR_PARITY |
- XUARTPS_IXR_FRAMING | XUARTPS_IXR_OVERRUN;
+ port->ignore_status_mask |= CDNS_UART_IXR_PARITY |
+ CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN;
/* ignore all characters if CREAD is not set */
if ((termios->c_cflag & CREAD) == 0)
- port->ignore_status_mask |= XUARTPS_IXR_RXTRIG |
- XUARTPS_IXR_TOUT | XUARTPS_IXR_PARITY |
- XUARTPS_IXR_FRAMING | XUARTPS_IXR_OVERRUN;
+ port->ignore_status_mask |= CDNS_UART_IXR_RXTRIG |
+ CDNS_UART_IXR_TOUT | CDNS_UART_IXR_PARITY |
+ CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN;
- mode_reg = xuartps_readl(XUARTPS_MR_OFFSET);
+ mode_reg = cdns_uart_readl(CDNS_UART_MR_OFFSET);
/* Handling Data Size */
switch (termios->c_cflag & CSIZE) {
case CS6:
- cval |= XUARTPS_MR_CHARLEN_6_BIT;
+ cval |= CDNS_UART_MR_CHARLEN_6_BIT;
break;
case CS7:
- cval |= XUARTPS_MR_CHARLEN_7_BIT;
+ cval |= CDNS_UART_MR_CHARLEN_7_BIT;
break;
default:
case CS8:
- cval |= XUARTPS_MR_CHARLEN_8_BIT;
+ cval |= CDNS_UART_MR_CHARLEN_8_BIT;
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= CS8;
break;
@@ -703,133 +709,135 @@ static void xuartps_set_termios(struct uart_port *port,
/* Handling Parity and Stop Bits length */
if (termios->c_cflag & CSTOPB)
- cval |= XUARTPS_MR_STOPMODE_2_BIT; /* 2 STOP bits */
+ cval |= CDNS_UART_MR_STOPMODE_2_BIT; /* 2 STOP bits */
else
- cval |= XUARTPS_MR_STOPMODE_1_BIT; /* 1 STOP bit */
+ cval |= CDNS_UART_MR_STOPMODE_1_BIT; /* 1 STOP bit */
if (termios->c_cflag & PARENB) {
/* Mark or Space parity */
if (termios->c_cflag & CMSPAR) {
if (termios->c_cflag & PARODD)
- cval |= XUARTPS_MR_PARITY_MARK;
+ cval |= CDNS_UART_MR_PARITY_MARK;
else
- cval |= XUARTPS_MR_PARITY_SPACE;
+ cval |= CDNS_UART_MR_PARITY_SPACE;
} else {
if (termios->c_cflag & PARODD)
- cval |= XUARTPS_MR_PARITY_ODD;
+ cval |= CDNS_UART_MR_PARITY_ODD;
else
- cval |= XUARTPS_MR_PARITY_EVEN;
+ cval |= CDNS_UART_MR_PARITY_EVEN;
}
} else {
- cval |= XUARTPS_MR_PARITY_NONE;
+ cval |= CDNS_UART_MR_PARITY_NONE;
}
cval |= mode_reg & 1;
- xuartps_writel(cval, XUARTPS_MR_OFFSET);
+ cdns_uart_writel(cval, CDNS_UART_MR_OFFSET);
spin_unlock_irqrestore(&port->lock, flags);
}
/**
- * xuartps_startup - Called when an application opens a xuartps port
+ * cdns_uart_startup - Called when an application opens a cdns_uart port
* @port: Handle to the uart port structure
*
* Return: 0 on success, negative errno otherwise
*/
-static int xuartps_startup(struct uart_port *port)
+static int cdns_uart_startup(struct uart_port *port)
{
unsigned int retval = 0, status = 0;
- retval = request_irq(port->irq, xuartps_isr, 0, XUARTPS_NAME,
+ retval = request_irq(port->irq, cdns_uart_isr, 0, CDNS_UART_NAME,
(void *)port);
if (retval)
return retval;
/* Disable the TX and RX */
- xuartps_writel(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS,
- XUARTPS_CR_OFFSET);
+ cdns_uart_writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS,
+ CDNS_UART_CR_OFFSET);
/* Set the Control Register with TX/RX Enable, TX/RX Reset,
* no break chars.
*/
- xuartps_writel(XUARTPS_CR_TXRST | XUARTPS_CR_RXRST,
- XUARTPS_CR_OFFSET);
+ cdns_uart_writel(CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST,
+ CDNS_UART_CR_OFFSET);
- status = xuartps_readl(XUARTPS_CR_OFFSET);
+ status = cdns_uart_readl(CDNS_UART_CR_OFFSET);
/* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
*/
- xuartps_writel((status & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS))
- | (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN |
- XUARTPS_CR_STOPBRK), XUARTPS_CR_OFFSET);
+ cdns_uart_writel((status & ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS))
+ | (CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN |
+ CDNS_UART_CR_STOPBRK), CDNS_UART_CR_OFFSET);
/* Set the Mode Register with normal mode,8 data bits,1 stop bit,
* no parity.
*/
- xuartps_writel(XUARTPS_MR_CHMODE_NORM | XUARTPS_MR_STOPMODE_1_BIT
- | XUARTPS_MR_PARITY_NONE | XUARTPS_MR_CHARLEN_8_BIT,
- XUARTPS_MR_OFFSET);
+ cdns_uart_writel(CDNS_UART_MR_CHMODE_NORM | CDNS_UART_MR_STOPMODE_1_BIT
+ | CDNS_UART_MR_PARITY_NONE | CDNS_UART_MR_CHARLEN_8_BIT,
+ CDNS_UART_MR_OFFSET);
/*
* Set the RX FIFO Trigger level to use most of the FIFO, but it
* can be tuned with a module parameter
*/
- xuartps_writel(rx_trigger_level, XUARTPS_RXWM_OFFSET);
+ cdns_uart_writel(rx_trigger_level, CDNS_UART_RXWM_OFFSET);
/*
* Receive Timeout register is enabled but it
* can be tuned with a module parameter
*/
- xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
+ cdns_uart_writel(rx_timeout, CDNS_UART_RXTOUT_OFFSET);
/* Clear out any pending interrupts before enabling them */
- xuartps_writel(xuartps_readl(XUARTPS_ISR_OFFSET), XUARTPS_ISR_OFFSET);
+ cdns_uart_writel(cdns_uart_readl(CDNS_UART_ISR_OFFSET),
+ CDNS_UART_ISR_OFFSET);
/* Set the Interrupt Registers with desired interrupts */
- xuartps_writel(XUARTPS_IXR_TXEMPTY | XUARTPS_IXR_PARITY |
- XUARTPS_IXR_FRAMING | XUARTPS_IXR_OVERRUN |
- XUARTPS_IXR_RXTRIG | XUARTPS_IXR_TOUT, XUARTPS_IER_OFFSET);
+ cdns_uart_writel(CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_PARITY |
+ CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN |
+ CDNS_UART_IXR_RXTRIG | CDNS_UART_IXR_TOUT,
+ CDNS_UART_IER_OFFSET);
return retval;
}
/**
- * xuartps_shutdown - Called when an application closes a xuartps port
+ * cdns_uart_shutdown - Called when an application closes a cdns_uart port
* @port: Handle to the uart port structure
*/
-static void xuartps_shutdown(struct uart_port *port)
+static void cdns_uart_shutdown(struct uart_port *port)
{
int status;
/* Disable interrupts */
- status = xuartps_readl(XUARTPS_IMR_OFFSET);
- xuartps_writel(status, XUARTPS_IDR_OFFSET);
+ status = cdns_uart_readl(CDNS_UART_IMR_OFFSET);
+ cdns_uart_writel(status, CDNS_UART_IDR_OFFSET);
/* Disable the TX and RX */
- xuartps_writel(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS,
- XUARTPS_CR_OFFSET);
+ cdns_uart_writel(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS,
+ CDNS_UART_CR_OFFSET);
free_irq(port->irq, port);
}
/**
- * xuartps_type - Set UART type to xuartps port
+ * cdns_uart_type - Set UART type to cdns_uart port
* @port: Handle to the uart port structure
*
* Return: string on success, NULL otherwise
*/
-static const char *xuartps_type(struct uart_port *port)
+static const char *cdns_uart_type(struct uart_port *port)
{
- return port->type == PORT_XUARTPS ? XUARTPS_NAME : NULL;
+ return port->type == PORT_XUARTPS ? CDNS_UART_NAME : NULL;
}
/**
- * xuartps_verify_port - Verify the port params
+ * cdns_uart_verify_port - Verify the port params
* @port: Handle to the uart port structure
* @ser: Handle to the structure whose members are compared
*
* Return: 0 on success, negative errno otherwise.
*/
-static int xuartps_verify_port(struct uart_port *port,
+static int cdns_uart_verify_port(struct uart_port *port,
struct serial_struct *ser)
{
if (ser->type != PORT_UNKNOWN && ser->type != PORT_XUARTPS)
@@ -846,170 +854,170 @@ static int xuartps_verify_port(struct uart_port *port,
}
/**
- * xuartps_request_port - Claim the memory region attached to xuartps port,
- * called when the driver adds a xuartps port via
+ * cdns_uart_request_port - Claim the memory region attached to cdns_uart port,
+ * called when the driver adds a cdns_uart port via
* uart_add_one_port()
* @port: Handle to the uart port structure
*
* Return: 0 on success, negative errno otherwise.
*/
-static int xuartps_request_port(struct uart_port *port)
+static int cdns_uart_request_port(struct uart_port *port)
{
- if (!request_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE,
- XUARTPS_NAME)) {
+ if (!request_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE,
+ CDNS_UART_NAME)) {
return -ENOMEM;
}
- port->membase = ioremap(port->mapbase, XUARTPS_REGISTER_SPACE);
+ port->membase = ioremap(port->mapbase, CDNS_UART_REGISTER_SPACE);
if (!port->membase) {
dev_err(port->dev, "Unable to map registers\n");
- release_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE);
+ release_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE);
return -ENOMEM;
}
return 0;
}
/**
- * xuartps_release_port - Release UART port
+ * cdns_uart_release_port - Release UART port
* @port: Handle to the uart port structure
*
- * Release the memory region attached to a xuartps port. Called when the
- * driver removes a xuartps port via uart_remove_one_port().
+ * Release the memory region attached to a cdns_uart port. Called when the
+ * driver removes a cdns_uart port via uart_remove_one_port().
*/
-static void xuartps_release_port(struct uart_port *port)
+static void cdns_uart_release_port(struct uart_port *port)
{
- release_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE);
+ release_mem_region(port->mapbase, CDNS_UART_REGISTER_SPACE);
iounmap(port->membase);
port->membase = NULL;
}
/**
- * xuartps_config_port - Configure UART port
+ * cdns_uart_config_port - Configure UART port
* @port: Handle to the uart port structure
* @flags: If any
*/
-static void xuartps_config_port(struct uart_port *port, int flags)
+static void cdns_uart_config_port(struct uart_port *port, int flags)
{
- if (flags & UART_CONFIG_TYPE && xuartps_request_port(port) == 0)
+ if (flags & UART_CONFIG_TYPE && cdns_uart_request_port(port) == 0)
port->type = PORT_XUARTPS;
}
/**
- * xuartps_get_mctrl - Get the modem control state
+ * cdns_uart_get_mctrl - Get the modem control state
* @port: Handle to the uart port structure
*
* Return: the modem control state
*/
-static unsigned int xuartps_get_mctrl(struct uart_port *port)
+static unsigned int cdns_uart_get_mctrl(struct uart_port *port)
{
return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
}
-static void xuartps_set_mctrl(struct uart_port *port, unsigned int mctrl)
+static void cdns_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
/* N/A */
}
-static void xuartps_enable_ms(struct uart_port *port)
+static void cdns_uart_enable_ms(struct uart_port *port)
{
/* N/A */
}
#ifdef CONFIG_CONSOLE_POLL
-static int xuartps_poll_get_char(struct uart_port *port)
+static int cdns_uart_poll_get_char(struct uart_port *port)
{
u32 imr;
int c;
/* Disable all interrupts */
- imr = xuartps_readl(XUARTPS_IMR_OFFSET);
- xuartps_writel(imr, XUARTPS_IDR_OFFSET);
+ imr = cdns_uart_readl(CDNS_UART_IMR_OFFSET);
+ cdns_uart_writel(imr, CDNS_UART_IDR_OFFSET);
/* Check if FIFO is empty */
- if (xuartps_readl(XUARTPS_SR_OFFSET) & XUARTPS_SR_RXEMPTY)
+ if (cdns_uart_readl(CDNS_UART_SR_OFFSET) & CDNS_UART_SR_RXEMPTY)
c = NO_POLL_CHAR;
else /* Read a character */
- c = (unsigned char) xuartps_readl(XUARTPS_FIFO_OFFSET);
+ c = (unsigned char) cdns_uart_readl(CDNS_UART_FIFO_OFFSET);
/* Enable interrupts */
- xuartps_writel(imr, XUARTPS_IER_OFFSET);
+ cdns_uart_writel(imr, CDNS_UART_IER_OFFSET);
return c;
}
-static void xuartps_poll_put_char(struct uart_port *port, unsigned char c)
+static void cdns_uart_poll_put_char(struct uart_port *port, unsigned char c)
{
u32 imr;
/* Disable all interrupts */
- imr = xuartps_readl(XUARTPS_IMR_OFFSET);
- xuartps_writel(imr, XUARTPS_IDR_OFFSET);
+ imr = cdns_uart_readl(CDNS_UART_IMR_OFFSET);
+ cdns_uart_writel(imr, CDNS_UART_IDR_OFFSET);
/* Wait until FIFO is empty */
- while (!(xuartps_readl(XUARTPS_SR_OFFSET) & XUARTPS_SR_TXEMPTY))
+ while (!(cdns_uart_readl(CDNS_UART_SR_OFFSET) & CDNS_UART_SR_TXEMPTY))
cpu_relax();
/* Write a character */
- xuartps_writel(c, XUARTPS_FIFO_OFFSET);
+ cdns_uart_writel(c, CDNS_UART_FIFO_OFFSET);
/* Wait until FIFO is empty */
- while (!(xuartps_readl(XUARTPS_SR_OFFSET) & XUARTPS_SR_TXEMPTY))
+ while (!(cdns_uart_readl(CDNS_UART_SR_OFFSET) & CDNS_UART_SR_TXEMPTY))
cpu_relax();
/* Enable interrupts */
- xuartps_writel(imr, XUARTPS_IER_OFFSET);
+ cdns_uart_writel(imr, CDNS_UART_IER_OFFSET);
return;
}
#endif
-static struct uart_ops xuartps_ops = {
- .set_mctrl = xuartps_set_mctrl,
- .get_mctrl = xuartps_get_mctrl,
- .enable_ms = xuartps_enable_ms,
- .start_tx = xuartps_start_tx,
- .stop_tx = xuartps_stop_tx,
- .stop_rx = xuartps_stop_rx,
- .tx_empty = xuartps_tx_empty,
- .break_ctl = xuartps_break_ctl,
- .set_termios = xuartps_set_termios,
- .startup = xuartps_startup,
- .shutdown = xuartps_shutdown,
- .type = xuartps_type,
- .verify_port = xuartps_verify_port,
- .request_port = xuartps_request_port,
- .release_port = xuartps_release_port,
- .config_port = xuartps_config_port,
+static struct uart_ops cdns_uart_ops = {
+ .set_mctrl = cdns_uart_set_mctrl,
+ .get_mctrl = cdns_uart_get_mctrl,
+ .enable_ms = cdns_uart_enable_ms,
+ .start_tx = cdns_uart_start_tx,
+ .stop_tx = cdns_uart_stop_tx,
+ .stop_rx = cdns_uart_stop_rx,
+ .tx_empty = cdns_uart_tx_empty,
+ .break_ctl = cdns_uart_break_ctl,
+ .set_termios = cdns_uart_set_termios,
+ .startup = cdns_uart_startup,
+ .shutdown = cdns_uart_shutdown,
+ .type = cdns_uart_type,
+ .verify_port = cdns_uart_verify_port,
+ .request_port = cdns_uart_request_port,
+ .release_port = cdns_uart_release_port,
+ .config_port = cdns_uart_config_port,
#ifdef CONFIG_CONSOLE_POLL
- .poll_get_char = xuartps_poll_get_char,
- .poll_put_char = xuartps_poll_put_char,
+ .poll_get_char = cdns_uart_poll_get_char,
+ .poll_put_char = cdns_uart_poll_put_char,
#endif
};
-static struct uart_port xuartps_port[2];
+static struct uart_port cdns_uart_port[2];
/**
- * xuartps_get_port - Configure the port from the platform device resource info
+ * cdns_uart_get_port - Configure the port from platform device resource info
* @id: Port id
*
* Return: a pointer to a uart_port or NULL for failure
*/
-static struct uart_port *xuartps_get_port(int id)
+static struct uart_port *cdns_uart_get_port(int id)
{
struct uart_port *port;
/* Try the given port id if failed use default method */
- if (xuartps_port[id].mapbase != 0) {
+ if (cdns_uart_port[id].mapbase != 0) {
/* Find the next unused port */
- for (id = 0; id < XUARTPS_NR_PORTS; id++)
- if (xuartps_port[id].mapbase == 0)
+ for (id = 0; id < CDNS_UART_NR_PORTS; id++)
+ if (cdns_uart_port[id].mapbase == 0)
break;
}
- if (id >= XUARTPS_NR_PORTS)
+ if (id >= CDNS_UART_NR_PORTS)
return NULL;
- port = &xuartps_port[id];
+ port = &cdns_uart_port[id];
/* At this point, we've got an empty uart_port struct, initialize it */
spin_lock_init(&port->lock);
@@ -1019,8 +1027,8 @@ static struct uart_port *xuartps_get_port(int id)
port->type = PORT_UNKNOWN;
port->iotype = UPIO_MEM32;
port->flags = UPF_BOOT_AUTOCONF;
- port->ops = &xuartps_ops;
- port->fifosize = XUARTPS_FIFO_SIZE;
+ port->ops = &cdns_uart_ops;
+ port->fifosize = CDNS_UART_FIFO_SIZE;
port->line = id;
port->dev = NULL;
return port;
@@ -1028,37 +1036,37 @@ static struct uart_port *xuartps_get_port(int id)
#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
/**
- * xuartps_console_wait_tx - Wait for the TX to be full
+ * cdns_uart_console_wait_tx - Wait for the TX to be full
* @port: Handle to the uart port structure
*/
-static void xuartps_console_wait_tx(struct uart_port *port)
+static void cdns_uart_console_wait_tx(struct uart_port *port)
{
- while ((xuartps_readl(XUARTPS_SR_OFFSET) & XUARTPS_SR_TXEMPTY)
- != XUARTPS_SR_TXEMPTY)
+ while ((cdns_uart_readl(CDNS_UART_SR_OFFSET) & CDNS_UART_SR_TXEMPTY)
+ != CDNS_UART_SR_TXEMPTY)
barrier();
}
/**
- * xuartps_console_putchar - write the character to the FIFO buffer
+ * cdns_uart_console_putchar - write the character to the FIFO buffer
* @port: Handle to the uart port structure
* @ch: Character to be written
*/
-static void xuartps_console_putchar(struct uart_port *port, int ch)
+static void cdns_uart_console_putchar(struct uart_port *port, int ch)
{
- xuartps_console_wait_tx(port);
- xuartps_writel(ch, XUARTPS_FIFO_OFFSET);
+ cdns_uart_console_wait_tx(port);
+ cdns_uart_writel(ch, CDNS_UART_FIFO_OFFSET);
}
/**
- * xuartps_console_write - perform write operation
+ * cdns_uart_console_write - perform write operation
* @co: Console handle
* @s: Pointer to character array
* @count: No of characters
*/
-static void xuartps_console_write(struct console *co, const char *s,
+static void cdns_uart_console_write(struct console *co, const char *s,
unsigned int count)
{
- struct uart_port *port = &xuartps_port[co->index];
+ struct uart_port *port = &cdns_uart_port[co->index];
unsigned long flags;
unsigned int imr, ctrl;
int locked = 1;
@@ -1069,45 +1077,45 @@ static void xuartps_console_write(struct console *co, const char *s,
spin_lock_irqsave(&port->lock, flags);
/* save and disable interrupt */
- imr = xuartps_readl(XUARTPS_IMR_OFFSET);
- xuartps_writel(imr, XUARTPS_IDR_OFFSET);
+ imr = cdns_uart_readl(CDNS_UART_IMR_OFFSET);
+ cdns_uart_writel(imr, CDNS_UART_IDR_OFFSET);
/*
* Make sure that the tx part is enabled. Set the TX enable bit and
* clear the TX disable bit to enable the transmitter.
*/
- ctrl = xuartps_readl(XUARTPS_CR_OFFSET);
- xuartps_writel((ctrl & ~XUARTPS_CR_TX_DIS) | XUARTPS_CR_TX_EN,
- XUARTPS_CR_OFFSET);
+ ctrl = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ cdns_uart_writel((ctrl & ~CDNS_UART_CR_TX_DIS) | CDNS_UART_CR_TX_EN,
+ CDNS_UART_CR_OFFSET);
- uart_console_write(port, s, count, xuartps_console_putchar);
- xuartps_console_wait_tx(port);
+ uart_console_write(port, s, count, cdns_uart_console_putchar);
+ cdns_uart_console_wait_tx(port);
- xuartps_writel(ctrl, XUARTPS_CR_OFFSET);
+ cdns_uart_writel(ctrl, CDNS_UART_CR_OFFSET);
/* restore interrupt state */
- xuartps_writel(imr, XUARTPS_IER_OFFSET);
+ cdns_uart_writel(imr, CDNS_UART_IER_OFFSET);
if (locked)
spin_unlock_irqrestore(&port->lock, flags);
}
/**
- * xuartps_console_setup - Initialize the uart to default config
+ * cdns_uart_console_setup - Initialize the uart to default config
* @co: Console handle
* @options: Initial settings of uart
*
* Return: 0 on success, negative errno otherwise.
*/
-static int __init xuartps_console_setup(struct console *co, char *options)
+static int __init cdns_uart_console_setup(struct console *co, char *options)
{
- struct uart_port *port = &xuartps_port[co->index];
+ struct uart_port *port = &cdns_uart_port[co->index];
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
- if (co->index < 0 || co->index >= XUARTPS_NR_PORTS)
+ if (co->index < 0 || co->index >= CDNS_UART_NR_PORTS)
return -EINVAL;
if (!port->mapbase) {
@@ -1121,53 +1129,53 @@ static int __init xuartps_console_setup(struct console *co, char *options)
return uart_set_options(port, co, baud, parity, bits, flow);
}
-static struct uart_driver xuartps_uart_driver;
+static struct uart_driver cdns_uart_uart_driver;
-static struct console xuartps_console = {
- .name = XUARTPS_TTY_NAME,
- .write = xuartps_console_write,
+static struct console cdns_uart_console = {
+ .name = CDNS_UART_TTY_NAME,
+ .write = cdns_uart_console_write,
.device = uart_console_device,
- .setup = xuartps_console_setup,
+ .setup = cdns_uart_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1, /* Specified on the cmdline (e.g. console=ttyPS ) */
- .data = &xuartps_uart_driver,
+ .data = &cdns_uart_uart_driver,
};
/**
- * xuartps_console_init - Initialization call
+ * cdns_uart_console_init - Initialization call
*
* Return: 0 on success, negative errno otherwise
*/
-static int __init xuartps_console_init(void)
+static int __init cdns_uart_console_init(void)
{
- register_console(&xuartps_console);
+ register_console(&cdns_uart_console);
return 0;
}
-console_initcall(xuartps_console_init);
+console_initcall(cdns_uart_console_init);
#endif /* CONFIG_SERIAL_XILINX_PS_UART_CONSOLE */
-static struct uart_driver xuartps_uart_driver = {
+static struct uart_driver cdns_uart_uart_driver = {
.owner = THIS_MODULE,
- .driver_name = XUARTPS_NAME,
- .dev_name = XUARTPS_TTY_NAME,
- .major = XUARTPS_MAJOR,
- .minor = XUARTPS_MINOR,
- .nr = XUARTPS_NR_PORTS,
+ .driver_name = CDNS_UART_NAME,
+ .dev_name = CDNS_UART_TTY_NAME,
+ .major = CDNS_UART_MAJOR,
+ .minor = CDNS_UART_MINOR,
+ .nr = CDNS_UART_NR_PORTS,
#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
- .cons = &xuartps_console,
+ .cons = &cdns_uart_console,
#endif
};
#ifdef CONFIG_PM_SLEEP
/**
- * xuartps_suspend - suspend event
+ * cdns_uart_suspend - suspend event
* @device: Pointer to the device structure
*
* Return: 0
*/
-static int xuartps_suspend(struct device *device)
+static int cdns_uart_suspend(struct device *device)
{
struct uart_port *port = dev_get_drvdata(device);
struct tty_struct *tty;
@@ -1186,23 +1194,24 @@ static int xuartps_suspend(struct device *device)
* Call the API provided in serial_core.c file which handles
* the suspend.
*/
- uart_suspend_port(&xuartps_uart_driver, port);
+ uart_suspend_port(&cdns_uart_uart_driver, port);
if (console_suspend_enabled && !may_wake) {
- struct xuartps *xuartps = port->private_data;
+ struct cdns_uart *cdns_uart = port->private_data;
- clk_disable(xuartps->refclk);
- clk_disable(xuartps->aperclk);
+ clk_disable(cdns_uart->uartclk);
+ clk_disable(cdns_uart->pclk);
} else {
unsigned long flags = 0;
spin_lock_irqsave(&port->lock, flags);
/* Empty the receive FIFO 1st before making changes */
- while (!(xuartps_readl(XUARTPS_SR_OFFSET) & XUARTPS_SR_RXEMPTY))
- xuartps_readl(XUARTPS_FIFO_OFFSET);
+ while (!(cdns_uart_readl(CDNS_UART_SR_OFFSET) &
+ CDNS_UART_SR_RXEMPTY))
+ cdns_uart_readl(CDNS_UART_FIFO_OFFSET);
/* set RX trigger level to 1 */
- xuartps_writel(1, XUARTPS_RXWM_OFFSET);
+ cdns_uart_writel(1, CDNS_UART_RXWM_OFFSET);
/* disable RX timeout interrups */
- xuartps_writel(XUARTPS_IXR_TOUT, XUARTPS_IDR_OFFSET);
+ cdns_uart_writel(CDNS_UART_IXR_TOUT, CDNS_UART_IDR_OFFSET);
spin_unlock_irqrestore(&port->lock, flags);
}
@@ -1210,12 +1219,12 @@ static int xuartps_suspend(struct device *device)
}
/**
- * xuartps_resume - Resume after a previous suspend
+ * cdns_uart_resume - Resume after a previous suspend
* @device: Pointer to the device structure
*
* Return: 0
*/
-static int xuartps_resume(struct device *device)
+static int cdns_uart_resume(struct device *device)
{
struct uart_port *port = dev_get_drvdata(device);
unsigned long flags = 0;
@@ -1233,83 +1242,95 @@ static int xuartps_resume(struct device *device)
}
if (console_suspend_enabled && !may_wake) {
- struct xuartps *xuartps = port->private_data;
+ struct cdns_uart *cdns_uart = port->private_data;
- clk_enable(xuartps->aperclk);
- clk_enable(xuartps->refclk);
+ clk_enable(cdns_uart->pclk);
+ clk_enable(cdns_uart->uartclk);
spin_lock_irqsave(&port->lock, flags);
/* Set TX/RX Reset */
- ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- ctrl_reg |= XUARTPS_CR_TXRST | XUARTPS_CR_RXRST;
- xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
- while (xuartps_readl(XUARTPS_CR_OFFSET) &
- (XUARTPS_CR_TXRST | XUARTPS_CR_RXRST))
+ ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
+ cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
+ while (cdns_uart_readl(CDNS_UART_CR_OFFSET) &
+ (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
cpu_relax();
/* restore rx timeout value */
- xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
+ cdns_uart_writel(rx_timeout, CDNS_UART_RXTOUT_OFFSET);
/* Enable Tx/Rx */
- ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- ctrl_reg &= ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS);
- ctrl_reg |= XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN;
- xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
+ ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
+ ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
+ ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
+ cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
spin_unlock_irqrestore(&port->lock, flags);
} else {
spin_lock_irqsave(&port->lock, flags);
/* restore original rx trigger level */
- xuartps_writel(rx_trigger_level, XUARTPS_RXWM_OFFSET);
+ cdns_uart_writel(rx_trigger_level, CDNS_UART_RXWM_OFFSET);
/* enable RX timeout interrupt */
- xuartps_writel(XUARTPS_IXR_TOUT, XUARTPS_IER_OFFSET);
+ cdns_uart_writel(CDNS_UART_IXR_TOUT, CDNS_UART_IER_OFFSET);
spin_unlock_irqrestore(&port->lock, flags);
}
- return uart_resume_port(&xuartps_uart_driver, port);
+ return uart_resume_port(&cdns_uart_uart_driver, port);
}
#endif /* ! CONFIG_PM_SLEEP */
-static SIMPLE_DEV_PM_OPS(xuartps_dev_pm_ops, xuartps_suspend, xuartps_resume);
+static SIMPLE_DEV_PM_OPS(cdns_uart_dev_pm_ops, cdns_uart_suspend,
+ cdns_uart_resume);
/**
- * xuartps_probe - Platform driver probe
+ * cdns_uart_probe - Platform driver probe
* @pdev: Pointer to the platform device structure
*
* Return: 0 on success, negative errno otherwise
*/
-static int xuartps_probe(struct platform_device *pdev)
+static int cdns_uart_probe(struct platform_device *pdev)
{
int rc, id;
struct uart_port *port;
struct resource *res, *res2;
- struct xuartps *xuartps_data;
+ struct cdns_uart *cdns_uart_data;
- xuartps_data = devm_kzalloc(&pdev->dev, sizeof(*xuartps_data),
+ cdns_uart_data = devm_kzalloc(&pdev->dev, sizeof(*cdns_uart_data),
GFP_KERNEL);
- if (!xuartps_data)
+ if (!cdns_uart_data)
return -ENOMEM;
- xuartps_data->aperclk = devm_clk_get(&pdev->dev, "aper_clk");
- if (IS_ERR(xuartps_data->aperclk)) {
- dev_err(&pdev->dev, "aper_clk clock not found.\n");
- return PTR_ERR(xuartps_data->aperclk);
+ cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "pclk");
+ if (IS_ERR(cdns_uart_data->pclk)) {
+ cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "aper_clk");
+ if (!IS_ERR(cdns_uart_data->pclk))
+ dev_err(&pdev->dev, "clock name 'aper_clk' is deprecated.\n");
+ }
+ if (IS_ERR(cdns_uart_data->pclk)) {
+ dev_err(&pdev->dev, "pclk clock not found.\n");
+ return PTR_ERR(cdns_uart_data->pclk);
+ }
+
+ cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "uart_clk");
+ if (IS_ERR(cdns_uart_data->uartclk)) {
+ cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "ref_clk");
+ if (!IS_ERR(cdns_uart_data->uartclk))
+ dev_err(&pdev->dev, "clock name 'ref_clk' is deprecated.\n");
}
- xuartps_data->refclk = devm_clk_get(&pdev->dev, "ref_clk");
- if (IS_ERR(xuartps_data->refclk)) {
- dev_err(&pdev->dev, "ref_clk clock not found.\n");
- return PTR_ERR(xuartps_data->refclk);
+ if (IS_ERR(cdns_uart_data->uartclk)) {
+ dev_err(&pdev->dev, "uart_clk clock not found.\n");
+ return PTR_ERR(cdns_uart_data->uartclk);
}
- rc = clk_prepare_enable(xuartps_data->aperclk);
+ rc = clk_prepare_enable(cdns_uart_data->pclk);
if (rc) {
- dev_err(&pdev->dev, "Unable to enable APER clock.\n");
+ dev_err(&pdev->dev, "Unable to enable pclk clock.\n");
return rc;
}
- rc = clk_prepare_enable(xuartps_data->refclk);
+ rc = clk_prepare_enable(cdns_uart_data->uartclk);
if (rc) {
dev_err(&pdev->dev, "Unable to enable device clock.\n");
- goto err_out_clk_dis_aper;
+ goto err_out_clk_dis_pclk;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -1325,10 +1346,10 @@ static int xuartps_probe(struct platform_device *pdev)
}
#ifdef CONFIG_COMMON_CLK
- xuartps_data->clk_rate_change_nb.notifier_call =
- xuartps_clk_notifier_cb;
- if (clk_notifier_register(xuartps_data->refclk,
- &xuartps_data->clk_rate_change_nb))
+ cdns_uart_data->clk_rate_change_nb.notifier_call =
+ cdns_uart_clk_notifier_cb;
+ if (clk_notifier_register(cdns_uart_data->uartclk,
+ &cdns_uart_data->clk_rate_change_nb))
dev_warn(&pdev->dev, "Unable to register clock notifier.\n");
#endif
/* Look for a serialN alias */
@@ -1337,7 +1358,7 @@ static int xuartps_probe(struct platform_device *pdev)
id = 0;
/* Initialize the port structure */
- port = xuartps_get_port(id);
+ port = cdns_uart_get_port(id);
if (!port) {
dev_err(&pdev->dev, "Cannot get uart_port structure\n");
@@ -1351,11 +1372,11 @@ static int xuartps_probe(struct platform_device *pdev)
port->mapbase = res->start;
port->irq = res2->start;
port->dev = &pdev->dev;
- port->uartclk = clk_get_rate(xuartps_data->refclk);
- port->private_data = xuartps_data;
- xuartps_data->port = port;
+ port->uartclk = clk_get_rate(cdns_uart_data->uartclk);
+ port->private_data = cdns_uart_data;
+ cdns_uart_data->port = port;
platform_set_drvdata(pdev, port);
- rc = uart_add_one_port(&xuartps_uart_driver, port);
+ rc = uart_add_one_port(&cdns_uart_uart_driver, port);
if (rc) {
dev_err(&pdev->dev,
"uart_add_one_port() failed; err=%i\n", rc);
@@ -1366,88 +1387,89 @@ static int xuartps_probe(struct platform_device *pdev)
err_out_notif_unreg:
#ifdef CONFIG_COMMON_CLK
- clk_notifier_unregister(xuartps_data->refclk,
- &xuartps_data->clk_rate_change_nb);
+ clk_notifier_unregister(cdns_uart_data->uartclk,
+ &cdns_uart_data->clk_rate_change_nb);
#endif
err_out_clk_disable:
- clk_disable_unprepare(xuartps_data->refclk);
-err_out_clk_dis_aper:
- clk_disable_unprepare(xuartps_data->aperclk);
+ clk_disable_unprepare(cdns_uart_data->uartclk);
+err_out_clk_dis_pclk:
+ clk_disable_unprepare(cdns_uart_data->pclk);
return rc;
}
/**
- * xuartps_remove - called when the platform driver is unregistered
+ * cdns_uart_remove - called when the platform driver is unregistered
* @pdev: Pointer to the platform device structure
*
* Return: 0 on success, negative errno otherwise
*/
-static int xuartps_remove(struct platform_device *pdev)
+static int cdns_uart_remove(struct platform_device *pdev)
{
struct uart_port *port = platform_get_drvdata(pdev);
- struct xuartps *xuartps_data = port->private_data;
+ struct cdns_uart *cdns_uart_data = port->private_data;
int rc;
- /* Remove the xuartps port from the serial core */
+ /* Remove the cdns_uart port from the serial core */
#ifdef CONFIG_COMMON_CLK
- clk_notifier_unregister(xuartps_data->refclk,
- &xuartps_data->clk_rate_change_nb);
+ clk_notifier_unregister(cdns_uart_data->uartclk,
+ &cdns_uart_data->clk_rate_change_nb);
#endif
- rc = uart_remove_one_port(&xuartps_uart_driver, port);
+ rc = uart_remove_one_port(&cdns_uart_uart_driver, port);
port->mapbase = 0;
- clk_disable_unprepare(xuartps_data->refclk);
- clk_disable_unprepare(xuartps_data->aperclk);
+ clk_disable_unprepare(cdns_uart_data->uartclk);
+ clk_disable_unprepare(cdns_uart_data->pclk);
return rc;
}
/* Match table for of_platform binding */
-static struct of_device_id xuartps_of_match[] = {
+static struct of_device_id cdns_uart_of_match[] = {
{ .compatible = "xlnx,xuartps", },
+ { .compatible = "cdns,uart-r1p8", },
{}
};
-MODULE_DEVICE_TABLE(of, xuartps_of_match);
+MODULE_DEVICE_TABLE(of, cdns_uart_of_match);
-static struct platform_driver xuartps_platform_driver = {
- .probe = xuartps_probe,
- .remove = xuartps_remove,
+static struct platform_driver cdns_uart_platform_driver = {
+ .probe = cdns_uart_probe,
+ .remove = cdns_uart_remove,
.driver = {
.owner = THIS_MODULE,
- .name = XUARTPS_NAME,
- .of_match_table = xuartps_of_match,
- .pm = &xuartps_dev_pm_ops,
+ .name = CDNS_UART_NAME,
+ .of_match_table = cdns_uart_of_match,
+ .pm = &cdns_uart_dev_pm_ops,
},
};
-static int __init xuartps_init(void)
+static int __init cdns_uart_init(void)
{
int retval = 0;
- /* Register the xuartps driver with the serial core */
- retval = uart_register_driver(&xuartps_uart_driver);
+ /* Register the cdns_uart driver with the serial core */
+ retval = uart_register_driver(&cdns_uart_uart_driver);
if (retval)
return retval;
/* Register the platform driver */
- retval = platform_driver_register(&xuartps_platform_driver);
+ retval = platform_driver_register(&cdns_uart_platform_driver);
if (retval)
- uart_unregister_driver(&xuartps_uart_driver);
+ uart_unregister_driver(&cdns_uart_uart_driver);
return retval;
}
-static void __exit xuartps_exit(void)
+static void __exit cdns_uart_exit(void)
{
/* Unregister the platform driver */
- platform_driver_unregister(&xuartps_platform_driver);
+ platform_driver_unregister(&cdns_uart_platform_driver);
- /* Unregister the xuartps driver */
- uart_unregister_driver(&xuartps_uart_driver);
+ /* Unregister the cdns_uart driver */
+ uart_unregister_driver(&cdns_uart_uart_driver);
}
-module_init(xuartps_init);
-module_exit(xuartps_exit);
+module_init(cdns_uart_init);
+module_exit(cdns_uart_exit);
-MODULE_DESCRIPTION("Driver for PS UART");
+MODULE_DESCRIPTION("Driver for Cadence UART");
MODULE_AUTHOR("Xilinx Inc.");
MODULE_LICENSE("GPL");
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index b47dba2c1e6f..22aaf8ed7735 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -211,7 +211,7 @@
/* VIA VT8500 SoC */
#define PORT_VT8500 97
-/* Xilinx PSS UART */
+/* Cadence (Xilinx Zynq) UART */
#define PORT_XUARTPS 98
/* Atheros AR933X SoC */
--
1.9.1.1.gbb9f595
A lot of read-modify-write sequences used a one-line statement which
nests a readl() within a writel(). Convert this into code sequences that
make the three steps more obvious.
Signed-off-by: Soren Brinkmann <[email protected]>
Tested-by: Michal Simek <[email protected]>
---
Changes in v3: None
Changes in v2: None
drivers/tty/serial/xilinx_uartps.c | 52 ++++++++++++++++++--------------------
1 file changed, 24 insertions(+), 28 deletions(-)
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 814391038abb..b182ab8cfd07 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -437,9 +437,9 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
spin_lock_irqsave(&xuartps->port->lock, flags);
/* Disable the TX and RX to set baud rate */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
spin_unlock_irqrestore(&xuartps->port->lock, flags);
@@ -464,9 +464,9 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
spin_lock_irqsave(&xuartps->port->lock, flags);
/* Set TX/RX Reset */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TXRST | XUARTPS_CR_RXRST),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TXRST | XUARTPS_CR_RXRST;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
while (xuartps_readl(XUARTPS_CR_OFFSET) &
(XUARTPS_CR_TXRST | XUARTPS_CR_RXRST))
@@ -479,10 +479,9 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
*/
xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- xuartps_writel(
- (ctrl_reg & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS)) |
- (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN),
- XUARTPS_CR_OFFSET);
+ ctrl_reg &= ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS);
+ ctrl_reg |= XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
spin_unlock_irqrestore(&xuartps->port->lock, flags);
@@ -631,9 +630,9 @@ static void xuartps_set_termios(struct uart_port *port,
}
/* Disable the TX and RX to set baud rate */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
/*
* Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk
@@ -651,20 +650,18 @@ static void xuartps_set_termios(struct uart_port *port,
uart_update_timeout(port, termios->c_cflag, baud);
/* Set TX/RX Reset */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TXRST | XUARTPS_CR_RXRST),
- XUARTPS_CR_OFFSET);
-
ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TXRST | XUARTPS_CR_RXRST;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
*/
- xuartps_writel(
- (ctrl_reg & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS))
- | (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg &= ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS);
+ ctrl_reg |= XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
@@ -1248,9 +1245,9 @@ static int xuartps_resume(struct device *device)
spin_lock_irqsave(&port->lock, flags);
/* Set TX/RX Reset */
- xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
- (XUARTPS_CR_TXRST | XUARTPS_CR_RXRST),
- XUARTPS_CR_OFFSET);
+ ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
+ ctrl_reg |= XUARTPS_CR_TXRST | XUARTPS_CR_RXRST;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
while (xuartps_readl(XUARTPS_CR_OFFSET) &
(XUARTPS_CR_TXRST | XUARTPS_CR_RXRST))
cpu_relax();
@@ -1259,10 +1256,9 @@ static int xuartps_resume(struct device *device)
xuartps_writel(rx_timeout, XUARTPS_RXTOUT_OFFSET);
/* Enable Tx/Rx */
ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- xuartps_writel(
- (ctrl_reg & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS)) |
- (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN),
- XUARTPS_CR_OFFSET);
+ ctrl_reg &= ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS);
+ ctrl_reg |= XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN;
+ xuartps_writel(ctrl_reg, XUARTPS_CR_OFFSET);
spin_unlock_irqrestore(&port->lock, flags);
} else {
--
1.9.1.1.gbb9f595
From: Michal Simek <[email protected]>
Register port numbers according to order in DT aliases.
If aliases are not defined, order in DT is used.
If aliases are defined, register port id based
on that.
This patch ensures proper ttyPS0/1 assignment.
[soren]: Combined integer declarations in probe(), removed warning message
if no alias is found.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: Soren Brinkmann <[email protected]>
---
The alias is an optional feature. Print a warning if it is not provided
does not seem appropriate.
Changes in v3: None
Changes in v2:
- this patch has been added
---
drivers/tty/serial/xilinx_uartps.c | 24 ++++++++++++++++--------
1 file changed, 16 insertions(+), 8 deletions(-)
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index b2f929e48ddd..2cd0cd456c7a 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1031,17 +1031,21 @@ static struct uart_port xuartps_port[2];
* xuartps_get_port - Configure the port from the platform device resource
* info
*
+ * @id: Port id
+ *
* Return: a pointer to a uart_port or NULL for failure
*/
-static struct uart_port *xuartps_get_port(void)
+static struct uart_port *xuartps_get_port(int id)
{
struct uart_port *port;
- int id;
- /* Find the next unused port */
- for (id = 0; id < XUARTPS_NR_PORTS; id++)
- if (xuartps_port[id].mapbase == 0)
- break;
+ /* Try the given port id if failed use default method */
+ if (xuartps_port[id].mapbase != 0) {
+ /* Find the next unused port */
+ for (id = 0; id < XUARTPS_NR_PORTS; id++)
+ if (xuartps_port[id].mapbase == 0)
+ break;
+ }
if (id >= XUARTPS_NR_PORTS)
return NULL;
@@ -1329,7 +1333,7 @@ static SIMPLE_DEV_PM_OPS(xuartps_dev_pm_ops, xuartps_suspend, xuartps_resume);
*/
static int xuartps_probe(struct platform_device *pdev)
{
- int rc;
+ int rc, id;
struct uart_port *port;
struct resource *res, *res2;
struct xuartps *xuartps_data;
@@ -1380,9 +1384,13 @@ static int xuartps_probe(struct platform_device *pdev)
&xuartps_data->clk_rate_change_nb))
dev_warn(&pdev->dev, "Unable to register clock notifier.\n");
#endif
+ /* Look for a serialN alias */
+ id = of_alias_get_id(pdev->dev.of_node, "serial");
+ if (id < 0)
+ id = 0;
/* Initialize the port structure */
- port = xuartps_get_port();
+ port = xuartps_get_port(id);
if (!port) {
dev_err(&pdev->dev, "Cannot get uart_port structure\n");
--
1.9.1.1.gbb9f595
This is all white space and comment clean up. Mostly reformatting
comments.
Signed-off-by: Soren Brinkmann <[email protected]>
Tested-by: Michal Simek <[email protected]>
---
Changes in v3: None
Changes in v2: None
drivers/tty/serial/xilinx_uartps.c | 210 +++++++++++++------------------------
1 file changed, 74 insertions(+), 136 deletions(-)
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 2cd0cd456c7a..787a12064fa0 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1,14 +1,13 @@
/*
* Xilinx PS UART driver
*
- * 2011 - 2013 (C) Xilinx Inc.
+ * 2011 - 2014 (C) Xilinx Inc.
*
* This program is free software; you can redistribute it
* and/or modify it under the terms of the GNU General Public
* License as published by the Free Software Foundation;
* either version 2 of the License, or (at your option) any
* later version.
- *
*/
#if defined(CONFIG_SERIAL_XILINX_PS_UART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
@@ -49,39 +48,27 @@ static int rx_timeout = 10;
module_param(rx_timeout, uint, S_IRUGO);
MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
-/********************************Register Map********************************/
-/** UART
- *
- * Register offsets for the UART.
- *
- */
-#define XUARTPS_CR_OFFSET 0x00 /* Control Register [8:0] */
-#define XUARTPS_MR_OFFSET 0x04 /* Mode Register [10:0] */
-#define XUARTPS_IER_OFFSET 0x08 /* Interrupt Enable [10:0] */
-#define XUARTPS_IDR_OFFSET 0x0C /* Interrupt Disable [10:0] */
-#define XUARTPS_IMR_OFFSET 0x10 /* Interrupt Mask [10:0] */
-#define XUARTPS_ISR_OFFSET 0x14 /* Interrupt Status [10:0]*/
-#define XUARTPS_BAUDGEN_OFFSET 0x18 /* Baud Rate Generator [15:0] */
-#define XUARTPS_RXTOUT_OFFSET 0x1C /* RX Timeout [7:0] */
-#define XUARTPS_RXWM_OFFSET 0x20 /* RX FIFO Trigger Level [5:0] */
-#define XUARTPS_MODEMCR_OFFSET 0x24 /* Modem Control [5:0] */
-#define XUARTPS_MODEMSR_OFFSET 0x28 /* Modem Status [8:0] */
-#define XUARTPS_SR_OFFSET 0x2C /* Channel Status [11:0] */
-#define XUARTPS_FIFO_OFFSET 0x30 /* FIFO [15:0] or [7:0] */
-#define XUARTPS_BAUDDIV_OFFSET 0x34 /* Baud Rate Divider [7:0] */
-#define XUARTPS_FLOWDEL_OFFSET 0x38 /* Flow Delay [15:0] */
-#define XUARTPS_IRRX_PWIDTH_OFFSET 0x3C /* IR Minimum Received Pulse
- Width [15:0] */
-#define XUARTPS_IRTX_PWIDTH_OFFSET 0x40 /* IR Transmitted pulse
- Width [7:0] */
-#define XUARTPS_TXWM_OFFSET 0x44 /* TX FIFO Trigger Level [5:0] */
-
-/** Control Register
- *
- * The Control register (CR) controls the major functions of the device.
- *
- * Control Register Bit Definitions
- */
+/* Register offsets for the UART. */
+#define XUARTPS_CR_OFFSET 0x00 /* Control Register */
+#define XUARTPS_MR_OFFSET 0x04 /* Mode Register */
+#define XUARTPS_IER_OFFSET 0x08 /* Interrupt Enable */
+#define XUARTPS_IDR_OFFSET 0x0C /* Interrupt Disable */
+#define XUARTPS_IMR_OFFSET 0x10 /* Interrupt Mask */
+#define XUARTPS_ISR_OFFSET 0x14 /* Interrupt Status */
+#define XUARTPS_BAUDGEN_OFFSET 0x18 /* Baud Rate Generator */
+#define XUARTPS_RXTOUT_OFFSET 0x1C /* RX Timeout */
+#define XUARTPS_RXWM_OFFSET 0x20 /* RX FIFO Trigger Level */
+#define XUARTPS_MODEMCR_OFFSET 0x24 /* Modem Control */
+#define XUARTPS_MODEMSR_OFFSET 0x28 /* Modem Status */
+#define XUARTPS_SR_OFFSET 0x2C /* Channel Status */
+#define XUARTPS_FIFO_OFFSET 0x30 /* FIFO */
+#define XUARTPS_BAUDDIV_OFFSET 0x34 /* Baud Rate Divider */
+#define XUARTPS_FLOWDEL_OFFSET 0x38 /* Flow Delay */
+#define XUARTPS_IRRX_PWIDTH_OFFSET 0x3C /* IR Minimum Received Pulse Width */
+#define XUARTPS_IRTX_PWIDTH_OFFSET 0x40 /* IR Transmitted pulse Width */
+#define XUARTPS_TXWM_OFFSET 0x44 /* TX FIFO Trigger Level */
+
+/* Control Register Bit Definitions */
#define XUARTPS_CR_STOPBRK 0x00000100 /* Stop TX break */
#define XUARTPS_CR_STARTBRK 0x00000080 /* Set TX break */
#define XUARTPS_CR_TX_DIS 0x00000020 /* TX disabled. */
@@ -92,14 +79,11 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
#define XUARTPS_CR_RXRST 0x00000001 /* RX logic reset */
#define XUARTPS_CR_RST_TO 0x00000040 /* Restart Timeout Counter */
-/** Mode Register
- *
+/*
+ * Mode Register:
* The mode register (MR) defines the mode of transfer as well as the data
* format. If this register is modified during transmission or reception,
* data validity cannot be guaranteed.
- *
- * Mode Register Bit Definitions
- *
*/
#define XUARTPS_MR_CLKSEL 0x00000001 /* Pre-scalar selection */
#define XUARTPS_MR_CHMODE_L_LOOP 0x00000200 /* Local loop back mode */
@@ -118,8 +102,8 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
#define XUARTPS_MR_CHARLEN_7_BIT 0x00000004 /* 7 bits data */
#define XUARTPS_MR_CHARLEN_8_BIT 0x00000000 /* 8 bits data */
-/** Interrupt Registers
- *
+/*
+ * Interrupt Registers:
* Interrupt control logic uses the interrupt enable register (IER) and the
* interrupt disable register (IDR) to set the value of the bits in the
* interrupt mask register (IMR). The IMR determines whether to pass an
@@ -127,7 +111,6 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
* Writing a 1 to IER Enables an interrupt, writing a 1 to IDR disables an
* interrupt. IMR and ISR are read only, and IER and IDR are write only.
* Reading either IER or IDR returns 0x00.
- *
* All four registers have the same bit definitions.
*/
#define XUARTPS_IXR_TOUT 0x00000100 /* RX Timeout error interrupt */
@@ -145,8 +128,8 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
/* Goes in read_status_mask for break detection as the HW doesn't do it*/
#define XUARTPS_IXR_BRK 0x80000000
-/** Channel Status Register
- *
+/*
+ * Channel Status Register:
* The channel status register (CSR) is provided to enable the control logic
* to monitor the status of bits in the channel interrupt status register,
* even if these are masked out by the interrupt mask register.
@@ -205,7 +188,6 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
* error with all-zeros data as a break sequence. Most of the time,
* there's another non-zero byte at the end of the sequence.
*/
-
if (isrstatus & XUARTPS_IXR_FRAMING) {
while (!(xuartps_readl(XUARTPS_SR_OFFSET) &
XUARTPS_SR_RXEMPTY)) {
@@ -264,8 +246,9 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
} else if (isrstatus & XUARTPS_IXR_FRAMING) {
port->icount.frame++;
status = TTY_FRAME;
- } else if (isrstatus & XUARTPS_IXR_OVERRUN)
+ } else if (isrstatus & XUARTPS_IXR_OVERRUN) {
port->icount.overrun++;
+ }
uart_insert_char(port, isrstatus, XUARTPS_IXR_OVERRUN,
data, status);
@@ -300,7 +283,7 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
* the buffer if it reaches limit.
*/
port->state->xmit.tail =
- (port->state->xmit.tail + 1) & \
+ (port->state->xmit.tail + 1) &
(UART_XMIT_SIZE - 1);
}
@@ -419,7 +402,7 @@ static unsigned int xuartps_set_baud_rate(struct uart_port *port,
* @nb: Notifier block
* @event: Notify event
* @data: Notifier data
- * Return: NOTIFY_OK on success, NOTIFY_BAD on error.
+ * Return: NOTIFY_OK or NOTIFY_DONE on success, NOTIFY_BAD on error.
*/
static int xuartps_clk_notifier_cb(struct notifier_block *nb,
unsigned long event, void *data)
@@ -438,8 +421,7 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
switch (event) {
case PRE_RATE_CHANGE:
{
- u32 bdiv;
- u32 cd;
+ u32 bdiv, cd;
int div8;
/*
@@ -509,8 +491,6 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
}
#endif
-/*----------------------Uart Operations---------------------------*/
-
/**
* xuartps_start_tx - Start transmitting bytes
* @port: Handle to the uart port structure
@@ -529,9 +509,8 @@ static void xuartps_start_tx(struct uart_port *port)
xuartps_writel((status & ~XUARTPS_CR_TX_DIS) | XUARTPS_CR_TX_EN,
XUARTPS_CR_OFFSET);
- while (numbytes-- && ((xuartps_readl(XUARTPS_SR_OFFSET)
- & XUARTPS_SR_TXFULL)) != XUARTPS_SR_TXFULL) {
-
+ while (numbytes-- && ((xuartps_readl(XUARTPS_SR_OFFSET) &
+ XUARTPS_SR_TXFULL)) != XUARTPS_SR_TXFULL) {
/* Break if no more data available in the UART buffer */
if (uart_circ_empty(&port->state->xmit))
break;
@@ -666,9 +645,7 @@ static void xuartps_set_termios(struct uart_port *port,
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
- /*
- * Update the per-port timeout.
- */
+ /* Update the per-port timeout. */
uart_update_timeout(port, termios->c_cflag, baud);
/* Set TX/RX Reset */
@@ -678,7 +655,8 @@ static void xuartps_set_termios(struct uart_port *port,
ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
- /* Clear the RX disable and TX disable bits and then set the TX enable
+ /*
+ * Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
*/
xuartps_writel(
@@ -756,7 +734,7 @@ static void xuartps_set_termios(struct uart_port *port,
* xuartps_startup - Called when an application opens a xuartps port
* @port: Handle to the uart port structure
*
- * Return: 0 on success, negative error otherwise
+ * Return: 0 on success, negative errno otherwise
*/
static int xuartps_startup(struct uart_port *port)
{
@@ -850,7 +828,7 @@ static const char *xuartps_type(struct uart_port *port)
* @port: Handle to the uart port structure
* @ser: Handle to the structure whose members are compared
*
- * Return: 0 if success otherwise -EINVAL
+ * Return: 0 on success, negative errno otherwise.
*/
static int xuartps_verify_port(struct uart_port *port,
struct serial_struct *ser)
@@ -874,7 +852,7 @@ static int xuartps_verify_port(struct uart_port *port,
* uart_add_one_port()
* @port: Handle to the uart port structure
*
- * Return: 0, -ENOMEM if request fails
+ * Return: 0 on success, negative errno otherwise.
*/
static int xuartps_request_port(struct uart_port *port)
{
@@ -893,10 +871,11 @@ static int xuartps_request_port(struct uart_port *port)
}
/**
- * xuartps_release_port - Release the memory region attached to a xuartps
- * port, called when the driver removes a xuartps
- * port via uart_remove_one_port().
+ * xuartps_release_port - Release UART port
* @port: Handle to the uart port structure
+ *
+ * Release the memory region attached to a xuartps port. Called when the
+ * driver removes a xuartps port via uart_remove_one_port().
*/
static void xuartps_release_port(struct uart_port *port)
{
@@ -906,8 +885,7 @@ static void xuartps_release_port(struct uart_port *port)
}
/**
- * xuartps_config_port - Configure xuartps, called when the driver adds a
- * xuartps port
+ * xuartps_config_port - Configure UART port
* @port: Handle to the uart port structure
* @flags: If any
*/
@@ -919,7 +897,6 @@ static void xuartps_config_port(struct uart_port *port, int flags)
/**
* xuartps_get_mctrl - Get the modem control state
- *
* @port: Handle to the uart port structure
*
* Return: the modem control state
@@ -987,38 +964,23 @@ static void xuartps_poll_put_char(struct uart_port *port, unsigned char c)
}
#endif
-/** The UART operations structure
- */
static struct uart_ops xuartps_ops = {
.set_mctrl = xuartps_set_mctrl,
.get_mctrl = xuartps_get_mctrl,
.enable_ms = xuartps_enable_ms,
-
- .start_tx = xuartps_start_tx, /* Start transmitting */
- .stop_tx = xuartps_stop_tx, /* Stop transmission */
- .stop_rx = xuartps_stop_rx, /* Stop reception */
- .tx_empty = xuartps_tx_empty, /* Transmitter busy? */
- .break_ctl = xuartps_break_ctl, /* Start/stop
- * transmitting break
- */
- .set_termios = xuartps_set_termios, /* Set termios */
- .startup = xuartps_startup, /* App opens xuartps */
- .shutdown = xuartps_shutdown, /* App closes xuartps */
- .type = xuartps_type, /* Set UART type */
- .verify_port = xuartps_verify_port, /* Verification of port
- * params
- */
- .request_port = xuartps_request_port, /* Claim resources
- * associated with a
- * xuartps port
- */
- .release_port = xuartps_release_port, /* Release resources
- * associated with a
- * xuartps port
- */
- .config_port = xuartps_config_port, /* Configure when driver
- * adds a xuartps port
- */
+ .start_tx = xuartps_start_tx,
+ .stop_tx = xuartps_stop_tx,
+ .stop_rx = xuartps_stop_rx,
+ .tx_empty = xuartps_tx_empty,
+ .break_ctl = xuartps_break_ctl,
+ .set_termios = xuartps_set_termios,
+ .startup = xuartps_startup,
+ .shutdown = xuartps_shutdown,
+ .type = xuartps_type,
+ .verify_port = xuartps_verify_port,
+ .request_port = xuartps_request_port,
+ .release_port = xuartps_release_port,
+ .config_port = xuartps_config_port,
#ifdef CONFIG_CONSOLE_POLL
.poll_get_char = xuartps_poll_get_char,
.poll_put_char = xuartps_poll_put_char,
@@ -1028,9 +990,7 @@ static struct uart_ops xuartps_ops = {
static struct uart_port xuartps_port[2];
/**
- * xuartps_get_port - Configure the port from the platform device resource
- * info
- *
+ * xuartps_get_port - Configure the port from the platform device resource info
* @id: Port id
*
* Return: a pointer to a uart_port or NULL for failure
@@ -1067,8 +1027,6 @@ static struct uart_port *xuartps_get_port(int id)
return port;
}
-/*-----------------------Console driver operations--------------------------*/
-
#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
/**
* xuartps_console_wait_tx - Wait for the TX to be full
@@ -1144,7 +1102,7 @@ static void xuartps_console_write(struct console *co, const char *s,
* @co: Console handle
* @options: Initial settings of uart
*
- * Return: 0, -ENODEV if no device
+ * Return: 0 on success, negative errno otherwise.
*/
static int __init xuartps_console_setup(struct console *co, char *options)
{
@@ -1183,7 +1141,7 @@ static struct console xuartps_console = {
/**
* xuartps_console_init - Initialization call
*
- * Return: 0 on success, negative error otherwise
+ * Return: 0 on success, negative errno otherwise
*/
static int __init xuartps_console_init(void)
{
@@ -1195,17 +1153,15 @@ console_initcall(xuartps_console_init);
#endif /* CONFIG_SERIAL_XILINX_PS_UART_CONSOLE */
-/** Structure Definitions
- */
static struct uart_driver xuartps_uart_driver = {
- .owner = THIS_MODULE, /* Owner */
- .driver_name = XUARTPS_NAME, /* Driver name */
- .dev_name = XUARTPS_TTY_NAME, /* Node name */
- .major = XUARTPS_MAJOR, /* Major number */
- .minor = XUARTPS_MINOR, /* Minor number */
- .nr = XUARTPS_NR_PORTS, /* Number of UART ports */
+ .owner = THIS_MODULE,
+ .driver_name = XUARTPS_NAME,
+ .dev_name = XUARTPS_TTY_NAME,
+ .major = XUARTPS_MAJOR,
+ .minor = XUARTPS_MINOR,
+ .nr = XUARTPS_NR_PORTS,
#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
- .cons = &xuartps_console, /* Console */
+ .cons = &xuartps_console,
#endif
};
@@ -1322,14 +1278,11 @@ static int xuartps_resume(struct device *device)
static SIMPLE_DEV_PM_OPS(xuartps_dev_pm_ops, xuartps_suspend, xuartps_resume);
-/* ---------------------------------------------------------------------
- * Platform bus binding
- */
/**
* xuartps_probe - Platform driver probe
* @pdev: Pointer to the platform device structure
*
- * Return: 0 on success, negative error otherwise
+ * Return: 0 on success, negative errno otherwise
*/
static int xuartps_probe(struct platform_device *pdev)
{
@@ -1434,7 +1387,7 @@ err_out_clk_dis_aper:
* xuartps_remove - called when the platform driver is unregistered
* @pdev: Pointer to the platform device structure
*
- * Return: 0 on success, negative error otherwise
+ * Return: 0 on success, negative errno otherwise
*/
static int xuartps_remove(struct platform_device *pdev)
{
@@ -1462,24 +1415,16 @@ static struct of_device_id xuartps_of_match[] = {
MODULE_DEVICE_TABLE(of, xuartps_of_match);
static struct platform_driver xuartps_platform_driver = {
- .probe = xuartps_probe, /* Probe method */
- .remove = xuartps_remove, /* Detach method */
+ .probe = xuartps_probe,
+ .remove = xuartps_remove,
.driver = {
.owner = THIS_MODULE,
- .name = XUARTPS_NAME, /* Driver name */
+ .name = XUARTPS_NAME,
.of_match_table = xuartps_of_match,
.pm = &xuartps_dev_pm_ops,
},
};
-/* ---------------------------------------------------------------------
- * Module Init and Exit
- */
-/**
- * xuartps_init - Initial driver registration call
- *
- * Return: whether the registration was successful or not
- */
static int __init xuartps_init(void)
{
int retval = 0;
@@ -1497,15 +1442,8 @@ static int __init xuartps_init(void)
return retval;
}
-/**
- * xuartps_exit - Driver unregistration call
- */
static void __exit xuartps_exit(void)
{
- /* The order of unregistration is important. Unregister the
- * UART driver before the platform driver crashes the system.
- */
-
/* Unregister the platform driver */
platform_driver_unregister(&xuartps_platform_driver);
--
1.9.1.1.gbb9f595
Add binding documentation for the Cadence UART.
Signed-off-by: Soren Brinkmann <[email protected]>
Acked-by: Peter Crosthwaite <[email protected]>
Acked-by: Rob Herring <[email protected]>
Tested-by: Michal Simek <[email protected]>
---
Changes in v3: None
Changes in v2: None
.../devicetree/bindings/serial/cdns,uart.txt | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/cdns,uart.txt
diff --git a/Documentation/devicetree/bindings/serial/cdns,uart.txt b/Documentation/devicetree/bindings/serial/cdns,uart.txt
new file mode 100644
index 000000000000..a3eb154c32ca
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/cdns,uart.txt
@@ -0,0 +1,20 @@
+Binding for Cadence UART Controller
+
+Required properties:
+- compatible : should be "cdns,uart-r1p8", or "xlnx,xuartps"
+- reg: Should contain UART controller registers location and length.
+- interrupts: Should contain UART controller interrupts.
+- clocks: Must contain phandles to the UART clocks
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Tuple to identify input clocks, must contain "uart_clk" and "pclk"
+ See ../clocks/clock-bindings.txt for details.
+
+
+Example:
+ uart@e0000000 {
+ compatible = "cdns,uart-r1p8";
+ clocks = <&clkc 23>, <&clkc 40>;
+ clock-names = "uart_clk", "pclk";
+ reg = <0xE0000000 0x1000>;
+ interrupts = <0 27 4>;
+ };
--
1.9.1.1.gbb9f595
Hi Greg,
did you have a chance to look at this yet?
Thanks,
Sören
On Fri, 2014-04-04 at 05:23PM -0700, Soren Brinkmann wrote:
> From: Michal Simek <[email protected]>
>
> No functional changes.
>
> Signed-off-by: Michal Simek <[email protected]>
> ---
>
> Changes in v3: None
> Changes in v2:
> - this patch has been added
>
> ---
> drivers/tty/serial/xilinx_uartps.c | 109 +++++++++++++++++--------------------
> 1 file changed, 49 insertions(+), 60 deletions(-)
>
> diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
> index f619ad5b5eae..b2f929e48ddd 100644
> --- a/drivers/tty/serial/xilinx_uartps.c
> +++ b/drivers/tty/serial/xilinx_uartps.c
> @@ -163,11 +163,11 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
>
> /**
> * struct xuartps - device data
> - * @port Pointer to the UART port
> - * @refclk Reference clock
> - * @aperclk APB clock
> - * @baud Current baud rate
> - * @clk_rate_change_nb Notifier block for clock changes
> + * @port: Pointer to the UART port
> + * @refclk: Reference clock
> + * @aperclk: APB clock
> + * @baud: Current baud rate
> + * @clk_rate_change_nb: Notifier block for clock changes
> */
> struct xuartps {
> struct uart_port *port;
> @@ -183,8 +183,8 @@ struct xuartps {
> * @irq: Irq number
> * @dev_id: Id of the port
> *
> - * Returns IRQHANDLED
> - **/
> + * Return: IRQHANDLED
> + */
> static irqreturn_t xuartps_isr(int irq, void *dev_id)
> {
> struct uart_port *port = (struct uart_port *)dev_id;
> @@ -325,7 +325,7 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
> * @rbdiv: BDIV value (return value)
> * @rcd: CD value (return value)
> * @div8: Value for clk_sel bit in mod (return value)
> - * Returns baud rate, requested baud when possible, or actual baud when there
> + * Return: baud rate, requested baud when possible, or actual baud when there
> * was too much error, zero if no valid divisors are found.
> *
> * Formula to obtain baud rate is
> @@ -384,7 +384,7 @@ static unsigned int xuartps_calc_baud_divs(unsigned int clk, unsigned int baud,
> * xuartps_set_baud_rate - Calculate and set the baud rate
> * @port: Handle to the uart port structure
> * @baud: Baud rate to set
> - * Returns baud rate, requested baud when possible, or actual baud when there
> + * Return: baud rate, requested baud when possible, or actual baud when there
> * was too much error, zero if no valid divisors are found.
> */
> static unsigned int xuartps_set_baud_rate(struct uart_port *port,
> @@ -419,7 +419,7 @@ static unsigned int xuartps_set_baud_rate(struct uart_port *port,
> * @nb: Notifier block
> * @event: Notify event
> * @data: Notifier data
> - * Returns NOTIFY_OK on success, NOTIFY_BAD on error.
> + * Return: NOTIFY_OK on success, NOTIFY_BAD on error.
> */
> static int xuartps_clk_notifier_cb(struct notifier_block *nb,
> unsigned long event, void *data)
> @@ -514,8 +514,7 @@ static int xuartps_clk_notifier_cb(struct notifier_block *nb,
> /**
> * xuartps_start_tx - Start transmitting bytes
> * @port: Handle to the uart port structure
> - *
> - **/
> + */
> static void xuartps_start_tx(struct uart_port *port)
> {
> unsigned int status, numbytes = port->fifosize;
> @@ -562,8 +561,7 @@ static void xuartps_start_tx(struct uart_port *port)
> /**
> * xuartps_stop_tx - Stop TX
> * @port: Handle to the uart port structure
> - *
> - **/
> + */
> static void xuartps_stop_tx(struct uart_port *port)
> {
> unsigned int regval;
> @@ -577,8 +575,7 @@ static void xuartps_stop_tx(struct uart_port *port)
> /**
> * xuartps_stop_rx - Stop RX
> * @port: Handle to the uart port structure
> - *
> - **/
> + */
> static void xuartps_stop_rx(struct uart_port *port)
> {
> unsigned int regval;
> @@ -593,8 +590,8 @@ static void xuartps_stop_rx(struct uart_port *port)
> * xuartps_tx_empty - Check whether TX is empty
> * @port: Handle to the uart port structure
> *
> - * Returns TIOCSER_TEMT on success, 0 otherwise
> - **/
> + * Return: TIOCSER_TEMT on success, 0 otherwise
> + */
> static unsigned int xuartps_tx_empty(struct uart_port *port)
> {
> unsigned int status;
> @@ -608,8 +605,7 @@ static unsigned int xuartps_tx_empty(struct uart_port *port)
> * transmitting char breaks
> * @port: Handle to the uart port structure
> * @ctl: Value based on which start or stop decision is taken
> - *
> - **/
> + */
> static void xuartps_break_ctl(struct uart_port *port, int ctl)
> {
> unsigned int status;
> @@ -636,8 +632,7 @@ static void xuartps_break_ctl(struct uart_port *port, int ctl)
> * @port: Handle to the uart port structure
> * @termios: Handle to the input termios structure
> * @old: Values of the previously saved termios structure
> - *
> - **/
> + */
> static void xuartps_set_termios(struct uart_port *port,
> struct ktermios *termios, struct ktermios *old)
> {
> @@ -761,8 +756,8 @@ static void xuartps_set_termios(struct uart_port *port,
> * xuartps_startup - Called when an application opens a xuartps port
> * @port: Handle to the uart port structure
> *
> - * Returns 0 on success, negative error otherwise
> - **/
> + * Return: 0 on success, negative error otherwise
> + */
> static int xuartps_startup(struct uart_port *port)
> {
> unsigned int retval = 0, status = 0;
> @@ -824,8 +819,7 @@ static int xuartps_startup(struct uart_port *port)
> /**
> * xuartps_shutdown - Called when an application closes a xuartps port
> * @port: Handle to the uart port structure
> - *
> - **/
> + */
> static void xuartps_shutdown(struct uart_port *port)
> {
> int status;
> @@ -844,8 +838,8 @@ static void xuartps_shutdown(struct uart_port *port)
> * xuartps_type - Set UART type to xuartps port
> * @port: Handle to the uart port structure
> *
> - * Returns string on success, NULL otherwise
> - **/
> + * Return: string on success, NULL otherwise
> + */
> static const char *xuartps_type(struct uart_port *port)
> {
> return port->type == PORT_XUARTPS ? XUARTPS_NAME : NULL;
> @@ -856,8 +850,8 @@ static const char *xuartps_type(struct uart_port *port)
> * @port: Handle to the uart port structure
> * @ser: Handle to the structure whose members are compared
> *
> - * Returns 0 if success otherwise -EINVAL
> - **/
> + * Return: 0 if success otherwise -EINVAL
> + */
> static int xuartps_verify_port(struct uart_port *port,
> struct serial_struct *ser)
> {
> @@ -880,8 +874,8 @@ static int xuartps_verify_port(struct uart_port *port,
> * uart_add_one_port()
> * @port: Handle to the uart port structure
> *
> - * Returns 0, -ENOMEM if request fails
> - **/
> + * Return: 0, -ENOMEM if request fails
> + */
> static int xuartps_request_port(struct uart_port *port)
> {
> if (!request_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE,
> @@ -903,8 +897,7 @@ static int xuartps_request_port(struct uart_port *port)
> * port, called when the driver removes a xuartps
> * port via uart_remove_one_port().
> * @port: Handle to the uart port structure
> - *
> - **/
> + */
> static void xuartps_release_port(struct uart_port *port)
> {
> release_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE);
> @@ -917,8 +910,7 @@ static void xuartps_release_port(struct uart_port *port)
> * xuartps port
> * @port: Handle to the uart port structure
> * @flags: If any
> - *
> - **/
> + */
> static void xuartps_config_port(struct uart_port *port, int flags)
> {
> if (flags & UART_CONFIG_TYPE && xuartps_request_port(port) == 0)
> @@ -930,9 +922,8 @@ static void xuartps_config_port(struct uart_port *port, int flags)
> *
> * @port: Handle to the uart port structure
> *
> - * Returns the modem control state
> - *
> - **/
> + * Return: the modem control state
> + */
> static unsigned int xuartps_get_mctrl(struct uart_port *port)
> {
> return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
> @@ -1040,8 +1031,8 @@ static struct uart_port xuartps_port[2];
> * xuartps_get_port - Configure the port from the platform device resource
> * info
> *
> - * Returns a pointer to a uart_port or NULL for failure
> - **/
> + * Return: a pointer to a uart_port or NULL for failure
> + */
> static struct uart_port *xuartps_get_port(void)
> {
> struct uart_port *port;
> @@ -1078,8 +1069,7 @@ static struct uart_port *xuartps_get_port(void)
> /**
> * xuartps_console_wait_tx - Wait for the TX to be full
> * @port: Handle to the uart port structure
> - *
> - **/
> + */
> static void xuartps_console_wait_tx(struct uart_port *port)
> {
> while ((xuartps_readl(XUARTPS_SR_OFFSET) & XUARTPS_SR_TXEMPTY)
> @@ -1091,8 +1081,7 @@ static void xuartps_console_wait_tx(struct uart_port *port)
> * xuartps_console_putchar - write the character to the FIFO buffer
> * @port: Handle to the uart port structure
> * @ch: Character to be written
> - *
> - **/
> + */
> static void xuartps_console_putchar(struct uart_port *port, int ch)
> {
> xuartps_console_wait_tx(port);
> @@ -1101,10 +1090,10 @@ static void xuartps_console_putchar(struct uart_port *port, int ch)
>
> /**
> * xuartps_console_write - perform write operation
> - * @port: Handle to the uart port structure
> + * @co: Console handle
> * @s: Pointer to character array
> * @count: No of characters
> - **/
> + */
> static void xuartps_console_write(struct console *co, const char *s,
> unsigned int count)
> {
> @@ -1151,8 +1140,8 @@ static void xuartps_console_write(struct console *co, const char *s,
> * @co: Console handle
> * @options: Initial settings of uart
> *
> - * Returns 0, -ENODEV if no device
> - **/
> + * Return: 0, -ENODEV if no device
> + */
> static int __init xuartps_console_setup(struct console *co, char *options)
> {
> struct uart_port *port = &xuartps_port[co->index];
> @@ -1190,8 +1179,8 @@ static struct console xuartps_console = {
> /**
> * xuartps_console_init - Initialization call
> *
> - * Returns 0 on success, negative error otherwise
> - **/
> + * Return: 0 on success, negative error otherwise
> + */
> static int __init xuartps_console_init(void)
> {
> register_console(&xuartps_console);
> @@ -1221,7 +1210,7 @@ static struct uart_driver xuartps_uart_driver = {
> * xuartps_suspend - suspend event
> * @device: Pointer to the device structure
> *
> - * Returns 0
> + * Return: 0
> */
> static int xuartps_suspend(struct device *device)
> {
> @@ -1269,7 +1258,7 @@ static int xuartps_suspend(struct device *device)
> * xuartps_resume - Resume after a previous suspend
> * @device: Pointer to the device structure
> *
> - * Returns 0
> + * Return: 0
> */
> static int xuartps_resume(struct device *device)
> {
> @@ -1336,8 +1325,8 @@ static SIMPLE_DEV_PM_OPS(xuartps_dev_pm_ops, xuartps_suspend, xuartps_resume);
> * xuartps_probe - Platform driver probe
> * @pdev: Pointer to the platform device structure
> *
> - * Returns 0 on success, negative error otherwise
> - **/
> + * Return: 0 on success, negative error otherwise
> + */
> static int xuartps_probe(struct platform_device *pdev)
> {
> int rc;
> @@ -1437,8 +1426,8 @@ err_out_clk_dis_aper:
> * xuartps_remove - called when the platform driver is unregistered
> * @pdev: Pointer to the platform device structure
> *
> - * Returns 0 on success, negative error otherwise
> - **/
> + * Return: 0 on success, negative error otherwise
> + */
> static int xuartps_remove(struct platform_device *pdev)
> {
> struct uart_port *port = platform_get_drvdata(pdev);
> @@ -1481,8 +1470,8 @@ static struct platform_driver xuartps_platform_driver = {
> /**
> * xuartps_init - Initial driver registration call
> *
> - * Returns whether the registration was successful or not
> - **/
> + * Return: whether the registration was successful or not
> + */
> static int __init xuartps_init(void)
> {
> int retval = 0;
> @@ -1502,7 +1491,7 @@ static int __init xuartps_init(void)
>
> /**
> * xuartps_exit - Driver unregistration call
> - **/
> + */
> static void __exit xuartps_exit(void)
> {
> /* The order of unregistration is important. Unregister the
> --
> 1.9.1.1.gbb9f595
>
>
On 04/05/2014 02:23 AM, Soren Brinkmann wrote:
> Add binding documentation for the Cadence UART.
>
> Signed-off-by: Soren Brinkmann <[email protected]>
> Acked-by: Peter Crosthwaite <[email protected]>
> Acked-by: Rob Herring <[email protected]>
> Tested-by: Michal Simek <[email protected]>
> ---
>
> Changes in v3: None
> Changes in v2: None
>
> .../devicetree/bindings/serial/cdns,uart.txt | 20 ++++++++++++++++++++
> 1 file changed, 20 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/serial/cdns,uart.txt
>
> diff --git a/Documentation/devicetree/bindings/serial/cdns,uart.txt b/Documentation/devicetree/bindings/serial/cdns,uart.txt
> new file mode 100644
> index 000000000000..a3eb154c32ca
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/serial/cdns,uart.txt
> @@ -0,0 +1,20 @@
> +Binding for Cadence UART Controller
> +
> +Required properties:
> +- compatible : should be "cdns,uart-r1p8", or "xlnx,xuartps"
> +- reg: Should contain UART controller registers location and length.
> +- interrupts: Should contain UART controller interrupts.
> +- clocks: Must contain phandles to the UART clocks
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names: Tuple to identify input clocks, must contain "uart_clk" and "pclk"
> + See ../clocks/clock-bindings.txt for details.
> +
> +
> +Example:
> + uart@e0000000 {
> + compatible = "cdns,uart-r1p8";
> + clocks = <&clkc 23>, <&clkc 40>;
> + clock-names = "uart_clk", "pclk";
> + reg = <0xE0000000 0x1000>;
> + interrupts = <0 27 4>;
> + };
>
Applied to zynq/dt2 branch.
Thanks,
Michal
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: http://www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform
On 04/05/2014 02:23 AM, Soren Brinkmann wrote:
> The Zynq UART is Cadence IP and the driver has been renamed accordingly.
> Migrate the DT to use the new binding for the UART driver.
>
> Signed-off-by: Soren Brinkmann <[email protected]>
> Acked-by: Peter Crosthwaite <[email protected]>
> Acked-by: Rob Herring <[email protected]>
> Tested-by: Michal Simek <[email protected]>
> ---
> This change depends on 'tty: xuartps: Rebrand driver as Cadence UART',
> which introduces the new clock-names.
>
> Changes in v3: None
> Changes in v2: None
>
> Signed-off-by: Soren Brinkmann <[email protected]>
> ---
> arch/arm/boot/dts/zynq-7000.dtsi | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi
> index 789d0bacc110..d27eb5c21831 100644
> --- a/arch/arm/boot/dts/zynq-7000.dtsi
> +++ b/arch/arm/boot/dts/zynq-7000.dtsi
> @@ -73,19 +73,19 @@
> };
>
> uart0: uart@e0000000 {
> - compatible = "xlnx,xuartps";
> + compatible = "xlnx,xuartps", "cdns,uart-r1p8";
> status = "disabled";
> clocks = <&clkc 23>, <&clkc 40>;
> - clock-names = "ref_clk", "aper_clk";
> + clock-names = "uart_clk", "pclk";
> reg = <0xE0000000 0x1000>;
> interrupts = <0 27 4>;
> };
>
> uart1: uart@e0001000 {
> - compatible = "xlnx,xuartps";
> + compatible = "xlnx,xuartps", "cdns,uart-r1p8";
> status = "disabled";
> clocks = <&clkc 24>, <&clkc 41>;
> - clock-names = "ref_clk", "aper_clk";
> + clock-names = "uart_clk", "pclk";
> reg = <0xE0001000 0x1000>;
> interrupts = <0 50 4>;
> };
>
Applied to zynq/dt2 branch.
Thanks,
Michal
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: http://www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform
On Fri, Apr 18, 2014 at 09:11:28AM -0700, S?ren Brinkmann wrote:
> Hi Greg,
>
> did you have a chance to look at this yet?
Patches 1-7 now applied, thanks.
greg k-h