Changes for v5:
-move the clear exist timing setting to a common place rather than only in HS200 mode.
-put the patch 6 ahead of patch 5.
Haibo Chen (6):
mmc: sdhci-esdhc-imx: add imx7d support and support HS400
mmc: sdhci-esdhc-imx: add tuning-step seting support
mmc: sdhci-esdhc-imx: add compatible string in bingding doc
ARM: dts: imx7d-sdb: add eMMC5.0 support
mmc: sdhci-esdhc-imx: set back the burst_length_enable bit to 1
mmc: sdhci-esdhc-imx: change default watermark level and burst length
.../devicetree/bindings/mmc/fsl-imx-esdhc.txt | 6 ++
arch/arm/boot/dts/imx7d-sdb.dts | 13 +++
drivers/mmc/host/sdhci-esdhc-imx.c | 116 ++++++++++++++++++++-
include/linux/platform_data/mmc-esdhc-imx.h | 1 +
4 files changed, 132 insertions(+), 4 deletions(-)
--
1.9.1
The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.
So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.
Signed-off-by: Haibo Chen <[email protected]>
---
drivers/mmc/host/sdhci-esdhc-imx.c | 88 ++++++++++++++++++++++++++++++++++++--
1 file changed, 85 insertions(+), 3 deletions(-)
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index c6b9f64..2a816ad 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -44,6 +44,7 @@
#define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22)
#define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23)
#define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25)
+#define ESDHC_MIX_CTRL_HS400_EN (1 << 26)
/* Bits 3 and 6 are not SDHCI standard definitions */
#define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
/* Tuning bits */
@@ -60,6 +61,16 @@
#define ESDHC_TUNE_CTRL_MIN 0
#define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1)
+/* strobe dll register */
+#define ESDHC_STROBE_DLL_CTRL 0x70
+#define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0)
+#define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1)
+#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3
+
+#define ESDHC_STROBE_DLL_STATUS 0x74
+#define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1)
+#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1
+
#define ESDHC_TUNING_CTRL 0xcc
#define ESDHC_STD_TUNING_EN (1 << 24)
/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
@@ -120,6 +131,11 @@
#define ESDHC_FLAG_ERR004536 BIT(7)
/* The IP supports HS200 mode */
#define ESDHC_FLAG_HS200 BIT(8)
+/* The IP supports HS400 mode */
+#define ESDHC_FLAG_HS400 BIT(9)
+
+/* A higher clock ferquency than this rate requires strobell dll control */
+#define ESDHC_STROBE_DLL_CLK_FREQ 100000000
struct esdhc_soc_data {
u32 flags;
@@ -156,6 +172,12 @@ static struct esdhc_soc_data usdhc_imx6sx_data = {
| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
};
+static struct esdhc_soc_data usdhc_imx7d_data = {
+ .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
+ | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
+ | ESDHC_FLAG_HS400,
+};
+
struct pltfm_imx_data {
u32 scratchpad;
struct pinctrl *pinctrl;
@@ -199,6 +221,7 @@ static const struct of_device_id imx_esdhc_dt_ids[] = {
{ .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
{ .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
{ .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
+ { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
@@ -274,6 +297,9 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
| SDHCI_SUPPORT_SDR50
| SDHCI_USE_SDR50_TUNING;
+
+ if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
+ val |= SDHCI_SUPPORT_HS400;
}
}
@@ -774,6 +800,7 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
break;
case MMC_TIMING_UHS_SDR104:
case MMC_TIMING_MMC_HS200:
+ case MMC_TIMING_MMC_HS400:
pinctrl = imx_data->pins_200mhz;
break;
default:
@@ -784,12 +811,57 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
return pinctrl_select_state(imx_data->pinctrl, pinctrl);
}
+/*
+ * For HS400 eMMC, there is a data_strobe line, this signal is generated
+ * by the device and used for data output and CRC status response output
+ * in HS400 mode. The frequency of this signal follows the frequency of
+ * CLK generated by host. Host receive the data which is aligned to the
+ * edge of data_strobe line. Due to the time delay between CLK line and
+ * data_strobe line, if the delay time is larger than one clock cycle,
+ * then CLK and data_strobe line will misaligned, read error shows up.
+ * So when the CLK is higher than 100MHz, each clock cycle is short enough,
+ * host should config the delay target.
+ */
+static void esdhc_set_strobe_dll(struct sdhci_host *host)
+{
+ u32 v;
+
+ if (host->mmc->actual_clock > ESDHC_STROBE_DLL_CLK_FREQ) {
+ /* force a reset on strobe dll */
+ writel(ESDHC_STROBE_DLL_CTRL_RESET,
+ host->ioaddr + ESDHC_STROBE_DLL_CTRL);
+ /*
+ * enable strobe dll ctrl and adjust the delay target
+ * for the uSDHC loopback read clock
+ */
+ v = ESDHC_STROBE_DLL_CTRL_ENABLE |
+ (7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
+ writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
+ /* wait 1us to make sure strobe dll status register stable */
+ udelay(1);
+ v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS);
+ if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK))
+ dev_warn(mmc_dev(host->mmc),
+ "warning! HS400 strobe DLL status REF not lock!\n");
+ if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK))
+ dev_warn(mmc_dev(host->mmc),
+ "warning! HS400 strobe DLL status SLV not lock!\n");
+ }
+}
+
static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
{
+ u32 m;
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = pltfm_host->priv;
struct esdhc_platform_data *boarddata = &imx_data->boarddata;
+ /* disable ddr mode and disable HS400 mode */
+ m = readl(host->ioaddr + ESDHC_MIX_CTRL);
+ m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
+ writel(m, host->ioaddr + ESDHC_MIX_CTRL);
+ imx_data->is_ddr = 0;
+
switch (timing) {
case MMC_TIMING_UHS_SDR12:
case MMC_TIMING_UHS_SDR25:
@@ -799,9 +871,9 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
break;
case MMC_TIMING_UHS_DDR50:
case MMC_TIMING_MMC_DDR52:
- writel(readl(host->ioaddr + ESDHC_MIX_CTRL) |
- ESDHC_MIX_CTRL_DDREN,
- host->ioaddr + ESDHC_MIX_CTRL);
+ m = readl(host->ioaddr + ESDHC_MIX_CTRL);
+ m |= ESDHC_MIX_CTRL_DDREN;
+ writel(m, host->ioaddr + ESDHC_MIX_CTRL);
imx_data->is_ddr = 1;
if (boarddata->delay_line) {
u32 v;
@@ -813,6 +885,13 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
writel(v, host->ioaddr + ESDHC_DLL_CTRL);
}
break;
+ case MMC_TIMING_MMC_HS400:
+ m = readl(host->ioaddr + ESDHC_MIX_CTRL);
+ m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
+ writel(m, host->ioaddr + ESDHC_MIX_CTRL);
+ imx_data->is_ddr = 1;
+ esdhc_set_strobe_dll(host);
+ break;
}
esdhc_change_pinstate(host, timing);
@@ -1100,6 +1179,9 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
+ if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
+ host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400;
+
if (of_id)
err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
else
--
1.9.1
tuning-step is the delay cell steps in tuning procedure. The default value
of tuning-step is 1. Some boards or cards need another value to pass the
tuning procedure. For example, imx7d-sdb board need the tuning-step value
as 2, otherwise it can't pass the tuning procedure.
So this patch add the tuning-step setting in driver, so that user can set
the tuning-step value in dts.
Signed-off-by: Haibo Chen <[email protected]>
---
drivers/mmc/host/sdhci-esdhc-imx.c | 9 +++++++++
include/linux/platform_data/mmc-esdhc-imx.h | 1 +
2 files changed, 10 insertions(+)
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 2a816ad..03c9f33 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -75,6 +75,7 @@
#define ESDHC_STD_TUNING_EN (1 << 24)
/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
#define ESDHC_TUNING_START_TAP 0x1
+#define ESDHC_TUNING_STEP_SHIFT 16
/* pinctrl state */
#define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz"
@@ -474,6 +475,7 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
} else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
u32 v = readl(host->ioaddr + SDHCI_ACMD12_ERR);
u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
+ u32 tuning_ctrl;
if (val & SDHCI_CTRL_TUNED_CLK) {
v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
} else {
@@ -484,6 +486,11 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
if (val & SDHCI_CTRL_EXEC_TUNING) {
v |= ESDHC_MIX_CTRL_EXE_TUNE;
m |= ESDHC_MIX_CTRL_FBCLK_SEL;
+ tuning_ctrl = readl(host->ioaddr + ESDHC_TUNING_CTRL);
+ tuning_ctrl |= ESDHC_STD_TUNING_EN | ESDHC_TUNING_START_TAP;
+ if (imx_data->boarddata.tuning_step)
+ tuning_ctrl |= imx_data->boarddata.tuning_step << ESDHC_TUNING_STEP_SHIFT;
+ writel(tuning_ctrl, host->ioaddr + ESDHC_TUNING_CTRL);
} else {
v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
}
@@ -965,6 +972,8 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
if (gpio_is_valid(boarddata->wp_gpio))
boarddata->wp_type = ESDHC_WP_GPIO;
+ of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
+
if (of_find_property(np, "no-1-8-v", NULL))
boarddata->support_vsel = false;
else
diff --git a/include/linux/platform_data/mmc-esdhc-imx.h b/include/linux/platform_data/mmc-esdhc-imx.h
index e1571ef..95ccab3 100644
--- a/include/linux/platform_data/mmc-esdhc-imx.h
+++ b/include/linux/platform_data/mmc-esdhc-imx.h
@@ -45,5 +45,6 @@ struct esdhc_platform_data {
int max_bus_width;
bool support_vsel;
unsigned int delay_line;
+ unsigned int tuning_step; /* The delay cell steps in tuning procedure */
};
#endif /* __ASM_ARCH_IMX_ESDHC_H */
--
1.9.1
Add a required property "fsl,imx7d-usdhc" in binding doc.
Add an optional property "fsl,tuning-step" in binding doc.
Signed-off-by: Haibo Chen <[email protected]>
---
Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
index 211e778..dca56d6 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
@@ -15,6 +15,7 @@ Required properties:
"fsl,imx6q-usdhc"
"fsl,imx6sl-usdhc"
"fsl,imx6sx-usdhc"
+ "fsl,imx7d-usdhc"
Optional properties:
- fsl,wp-controller : Indicate to use controller internal write protection
@@ -27,6 +28,11 @@ Optional properties:
transparent level shifters on the outputs of the controller. Two cells are
required, first cell specifies minimum slot voltage (mV), second cell
specifies maximum slot voltage (mV). Several ranges could be specified.
+- fsl,tuning-step: Specify the increasing delay cell steps in tuning procedure.
+ The uSDHC use one delay cell as default increasing step to do tuning process.
+ This property allows user to change the tuning step to more than one delay
+ cells which is useful for some special boards or cards when the default
+ tuning step can't find the proper delay window within limited tuning retries.
Examples:
--
1.9.1
imx7d-sdb board has a eMMC5.0 on usdhc3. This eMMC support HS400.
This patch add usdhc3 support for HS400
Signed-off-by: Haibo Chen <[email protected]>
---
arch/arm/boot/dts/imx7d-sdb.dts | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index fdd1d7c..8059458 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -241,6 +241,19 @@
status = "okay";
};
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+ assigned-clock-rates = <400000000>;
+ bus-width = <8>;
+ fsl,tuning-step = <2>;
+ non-removable;
+ status = "okay";
+};
+
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
--
1.9.1
Currently we find that if a usdhc is choosed to boot system, then ROM
code will set the burst length enable bit of this usdhc as 0.
This will make performance drop a lot if this usdhc's burst length is
configed. So this patch set back the burst_length_enable bit as 1,
which is the default value, and means burst length is enabled for INCR.
Signed-off-by: Haibo Chen <[email protected]>
---
drivers/mmc/host/sdhci-esdhc-imx.c | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 03c9f33..d7ec993 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -32,6 +32,7 @@
#include "sdhci-esdhc.h"
#define ESDHC_CTRL_D3CD 0x08
+#define ESDHC_BURST_LEN_EN_INCR (1 << 27)
/* VENDOR SPEC register */
#define ESDHC_VENDOR_SPEC 0xc0
#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1)
@@ -1165,6 +1166,21 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
host->mmc->caps |= MMC_CAP_1_8V_DDR;
+ /*
+ * ROM code will change the bit burst_length_enable setting
+ * to zero if this usdhc is choosed to boot system. Change
+ * it back here, otherwise it will impact the performance a
+ * lot. This bit is used to enable/disable the burst length
+ * for the external AHB2AXI bridge, it's usefully especially
+ * for INCR transfer because without burst length indicator,
+ * the AHB2AXI bridge does not know the burst length in
+ * advance. And without burst length indicator, AHB INCR
+ * transfer can only be converted to singles on the AXI side.
+ */
+ writel(readl(host->ioaddr + SDHCI_HOST_CONTROL)
+ | ESDHC_BURST_LEN_EN_INCR,
+ host->ioaddr + SDHCI_HOST_CONTROL);
+
if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200))
host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
--
1.9.1
By default, for all imx SoC types, the watermark level is 16, and the
burst length is 8. But if the SDIO/SD/MMC I/O speed is fast enough,
this default watermark level and burst length will be the performance
bottleneck.
For example, i.MX7D support eMMC HS400 mode, this mode can run in 8 bit,
200MHZ DDR mode. So the I/O speed improve a lot compare to SD3.0.
The default burst length is 8, if we don't change this value, in
HS400 mode, when we do eMMC read operation, we can find that the
clock signal will stop for a period of time. This means the speed
of data moving on AHB bus is slower than I/O speed. So we should
improve the speed of data moving on AHB bus.
This patch set the default burst length as 16, and set the default
watermark level as 64. The test result is the clock signal has
no stop during the eMMC HS400 operation.
Signed-off-by: Haibo Chen <[email protected]>
---
drivers/mmc/host/sdhci-esdhc-imx.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index d7ec993..1b31d36 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -1162,7 +1162,8 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
* to something insane. Change it back here.
*/
if (esdhc_is_usdhc(imx_data)) {
- writel(0x08100810, host->ioaddr + ESDHC_WTMK_LVL);
+ writel(0x10401040, host->ioaddr + ESDHC_WTMK_LVL);
+
host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
host->mmc->caps |= MMC_CAP_1_8V_DDR;
--
1.9.1
On Mon, Aug 10, 2015 at 04:18:03PM +0800, Haibo Chen wrote:
> The imx7d usdhc is derived from imx6sx, the difference is that
> imx7d support HS400.
>
> So introduce a new compatible string for imx7d and add HS400
> support for imx7d usdhc.
>
> Signed-off-by: Haibo Chen <[email protected]>
> ---
> drivers/mmc/host/sdhci-esdhc-imx.c | 88 ++++++++++++++++++++++++++++++++++++--
> 1 file changed, 85 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index c6b9f64..2a816ad 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -44,6 +44,7 @@
> #define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22)
> #define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23)
> #define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25)
> +#define ESDHC_MIX_CTRL_HS400_EN (1 << 26)
> /* Bits 3 and 6 are not SDHCI standard definitions */
> #define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
> /* Tuning bits */
> @@ -60,6 +61,16 @@
> #define ESDHC_TUNE_CTRL_MIN 0
> #define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1)
>
> +/* strobe dll register */
> +#define ESDHC_STROBE_DLL_CTRL 0x70
> +#define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0)
> +#define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1)
> +#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3
> +
> +#define ESDHC_STROBE_DLL_STATUS 0x74
> +#define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1)
> +#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1
> +
> #define ESDHC_TUNING_CTRL 0xcc
> #define ESDHC_STD_TUNING_EN (1 << 24)
> /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
> @@ -120,6 +131,11 @@
> #define ESDHC_FLAG_ERR004536 BIT(7)
> /* The IP supports HS200 mode */
> #define ESDHC_FLAG_HS200 BIT(8)
> +/* The IP supports HS400 mode */
> +#define ESDHC_FLAG_HS400 BIT(9)
> +
> +/* A higher clock ferquency than this rate requires strobell dll control */
> +#define ESDHC_STROBE_DLL_CLK_FREQ 100000000
>
> struct esdhc_soc_data {
> u32 flags;
> @@ -156,6 +172,12 @@ static struct esdhc_soc_data usdhc_imx6sx_data = {
> | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
> };
>
> +static struct esdhc_soc_data usdhc_imx7d_data = {
> + .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
> + | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
> + | ESDHC_FLAG_HS400,
> +};
> +
> struct pltfm_imx_data {
> u32 scratchpad;
> struct pinctrl *pinctrl;
> @@ -199,6 +221,7 @@ static const struct of_device_id imx_esdhc_dt_ids[] = {
> { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
> { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
> { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
> + { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
> @@ -274,6 +297,9 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
> val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
> | SDHCI_SUPPORT_SDR50
> | SDHCI_USE_SDR50_TUNING;
> +
> + if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
> + val |= SDHCI_SUPPORT_HS400;
> }
> }
>
> @@ -774,6 +800,7 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
> break;
> case MMC_TIMING_UHS_SDR104:
> case MMC_TIMING_MMC_HS200:
> + case MMC_TIMING_MMC_HS400:
> pinctrl = imx_data->pins_200mhz;
> break;
> default:
> @@ -784,12 +811,57 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
> return pinctrl_select_state(imx_data->pinctrl, pinctrl);
> }
>
> +/*
> + * For HS400 eMMC, there is a data_strobe line, this signal is generated
> + * by the device and used for data output and CRC status response output
> + * in HS400 mode. The frequency of this signal follows the frequency of
> + * CLK generated by host. Host receive the data which is aligned to the
> + * edge of data_strobe line. Due to the time delay between CLK line and
> + * data_strobe line, if the delay time is larger than one clock cycle,
> + * then CLK and data_strobe line will misaligned, read error shows up.
> + * So when the CLK is higher than 100MHz, each clock cycle is short enough,
> + * host should config the delay target.
> + */
> +static void esdhc_set_strobe_dll(struct sdhci_host *host)
> +{
> + u32 v;
> +
> + if (host->mmc->actual_clock > ESDHC_STROBE_DLL_CLK_FREQ) {
> + /* force a reset on strobe dll */
> + writel(ESDHC_STROBE_DLL_CTRL_RESET,
> + host->ioaddr + ESDHC_STROBE_DLL_CTRL);
> + /*
> + * enable strobe dll ctrl and adjust the delay target
> + * for the uSDHC loopback read clock
> + */
> + v = ESDHC_STROBE_DLL_CTRL_ENABLE |
> + (7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
> + writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
> + /* wait 1us to make sure strobe dll status register stable */
> + udelay(1);
> + v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS);
> + if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK))
> + dev_warn(mmc_dev(host->mmc),
> + "warning! HS400 strobe DLL status REF not lock!\n");
> + if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK))
> + dev_warn(mmc_dev(host->mmc),
> + "warning! HS400 strobe DLL status SLV not lock!\n");
> + }
> +}
> +
> static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
> {
> + u32 m;
> struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> struct pltfm_imx_data *imx_data = pltfm_host->priv;
> struct esdhc_platform_data *boarddata = &imx_data->boarddata;
>
> + /* disable ddr mode and disable HS400 mode */
> + m = readl(host->ioaddr + ESDHC_MIX_CTRL);
> + m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
> + writel(m, host->ioaddr + ESDHC_MIX_CTRL);
Is this write really required?
> + imx_data->is_ddr = 0;
> +
> switch (timing) {
> case MMC_TIMING_UHS_SDR12:
> case MMC_TIMING_UHS_SDR25:
> @@ -799,9 +871,9 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
> break;
> case MMC_TIMING_UHS_DDR50:
> case MMC_TIMING_MMC_DDR52:
> - writel(readl(host->ioaddr + ESDHC_MIX_CTRL) |
> - ESDHC_MIX_CTRL_DDREN,
> - host->ioaddr + ESDHC_MIX_CTRL);
> + m = readl(host->ioaddr + ESDHC_MIX_CTRL);
Can this line be droped if using the former readback mixctl value?
> + m |= ESDHC_MIX_CTRL_DDREN;
> + writel(m, host->ioaddr + ESDHC_MIX_CTRL);
> imx_data->is_ddr = 1;
> if (boarddata->delay_line) {
> u32 v;
> @@ -813,6 +885,13 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
> writel(v, host->ioaddr + ESDHC_DLL_CTRL);
> }
> break;
> + case MMC_TIMING_MMC_HS400:
> + m = readl(host->ioaddr + ESDHC_MIX_CTRL);
ditto
Regards
Dong Aisheng
> + m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
> + writel(m, host->ioaddr + ESDHC_MIX_CTRL);
> + imx_data->is_ddr = 1;
> + esdhc_set_strobe_dll(host);
> + break;
> }
>
> esdhc_change_pinstate(host, timing);
> @@ -1100,6 +1179,9 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
> if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
> host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
>
> + if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
> + host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400;
> +
> if (of_id)
> err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
> else
> --
> 1.9.1
>
On Mon, Aug 10, 2015 at 04:18:04PM +0800, Haibo Chen wrote:
> tuning-step is the delay cell steps in tuning procedure. The default value
> of tuning-step is 1. Some boards or cards need another value to pass the
> tuning procedure. For example, imx7d-sdb board need the tuning-step value
> as 2, otherwise it can't pass the tuning procedure.
>
> So this patch add the tuning-step setting in driver, so that user can set
> the tuning-step value in dts.
>
Fix a typo.
For patch title:
mmc: sdhci-esdhc-imx: add tuning-step seting support
s/seting/setting
Regards
Dong Aisheng
> Signed-off-by: Haibo Chen <[email protected]>
> ---
> drivers/mmc/host/sdhci-esdhc-imx.c | 9 +++++++++
> include/linux/platform_data/mmc-esdhc-imx.h | 1 +
> 2 files changed, 10 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index 2a816ad..03c9f33 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -75,6 +75,7 @@
> #define ESDHC_STD_TUNING_EN (1 << 24)
> /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
> #define ESDHC_TUNING_START_TAP 0x1
> +#define ESDHC_TUNING_STEP_SHIFT 16
>
> /* pinctrl state */
> #define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz"
> @@ -474,6 +475,7 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
> } else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
> u32 v = readl(host->ioaddr + SDHCI_ACMD12_ERR);
> u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
> + u32 tuning_ctrl;
> if (val & SDHCI_CTRL_TUNED_CLK) {
> v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
> } else {
> @@ -484,6 +486,11 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
> if (val & SDHCI_CTRL_EXEC_TUNING) {
> v |= ESDHC_MIX_CTRL_EXE_TUNE;
> m |= ESDHC_MIX_CTRL_FBCLK_SEL;
> + tuning_ctrl = readl(host->ioaddr + ESDHC_TUNING_CTRL);
> + tuning_ctrl |= ESDHC_STD_TUNING_EN | ESDHC_TUNING_START_TAP;
> + if (imx_data->boarddata.tuning_step)
> + tuning_ctrl |= imx_data->boarddata.tuning_step << ESDHC_TUNING_STEP_SHIFT;
> + writel(tuning_ctrl, host->ioaddr + ESDHC_TUNING_CTRL);
> } else {
> v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
> }
> @@ -965,6 +972,8 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
> if (gpio_is_valid(boarddata->wp_gpio))
> boarddata->wp_type = ESDHC_WP_GPIO;
>
> + of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
> +
> if (of_find_property(np, "no-1-8-v", NULL))
> boarddata->support_vsel = false;
> else
> diff --git a/include/linux/platform_data/mmc-esdhc-imx.h b/include/linux/platform_data/mmc-esdhc-imx.h
> index e1571ef..95ccab3 100644
> --- a/include/linux/platform_data/mmc-esdhc-imx.h
> +++ b/include/linux/platform_data/mmc-esdhc-imx.h
> @@ -45,5 +45,6 @@ struct esdhc_platform_data {
> int max_bus_width;
> bool support_vsel;
> unsigned int delay_line;
> + unsigned int tuning_step; /* The delay cell steps in tuning procedure */
> };
> #endif /* __ASM_ARCH_IMX_ESDHC_H */
> --
> 1.9.1
>
On Mon, Aug 10, 2015 at 04:18:05PM +0800, Haibo Chen wrote:
> Add a required property "fsl,imx7d-usdhc" in binding doc.
> Add an optional property "fsl,tuning-step" in binding doc.
>
> Signed-off-by: Haibo Chen <[email protected]>
You missed my former comments.
The patch title is too generous.
Better to change to something like:
mmc: sdhci-esdhc-imx: add imx7d support in bingding doc
Regards
Dong Aisheng
> ---
> Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> index 211e778..dca56d6 100644
> --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> @@ -15,6 +15,7 @@ Required properties:
> "fsl,imx6q-usdhc"
> "fsl,imx6sl-usdhc"
> "fsl,imx6sx-usdhc"
> + "fsl,imx7d-usdhc"
>
> Optional properties:
> - fsl,wp-controller : Indicate to use controller internal write protection
> @@ -27,6 +28,11 @@ Optional properties:
> transparent level shifters on the outputs of the controller. Two cells are
> required, first cell specifies minimum slot voltage (mV), second cell
> specifies maximum slot voltage (mV). Several ranges could be specified.
> +- fsl,tuning-step: Specify the increasing delay cell steps in tuning procedure.
> + The uSDHC use one delay cell as default increasing step to do tuning process.
> + This property allows user to change the tuning step to more than one delay
> + cells which is useful for some special boards or cards when the default
> + tuning step can't find the proper delay window within limited tuning retries.
>
> Examples:
>
> --
> 1.9.1
>