From: Patrice Chotard <[email protected]>
This series cleans and fixes some bugs in MFD/GPIO STMPE drivers and prepare
the ground to add new STMPE1600 support.
STMPE1600 datasheet is available here :
http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/
i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html
Only STMPE1600 has been tested on STM32 platform. As i have no board with
others STMPE variant(STMPE610/STMPE801/STMPE811/STMPE1601/STMPE1801/STMPE2401
and STMPE2403), i put in CC boards's maintainers which are using others STMPE variant.
If they can kindly check that no regression has been introduce by this series
:
For ARM/FREESCALE IMX / MXC ARM ARCHITECTURE:
_ Shawn Guo <[email protected]>
_ Sascha Hauer <[email protected]>
For ARM/SOCFPGA ARCHITECTURE
_ Dinh Nguyen <[email protected]>
For SPEAR PLATFORM SUPPORT
_ Viresh Kumar <[email protected]>
_ Shiraz Hashim <[email protected]>
For Apalis/Colibri board SUPPORT
_ [email protected]
_ [email protected]
_ [email protected]
_ Thierry Reding <[email protected]>
_ Alexandre Courbot <[email protected]>
For ARM/Ux500 ARM ARCHITECTURE
_ Linus Walleij <[email protected]>
v1 => v2:
_ update Cc list
_ fix kbuild test robot warnings on original patch 3
_ split patch 6 to extract usage of generic bitmask name
_ split patch 6 and 7 and introduce a new way to access registers
for both mfd/stmpe and gpio/gpio-stmpe drivers.
_ remove patch 8
Patrice Chotard (10):
mfd: stmpe: Add STMPE_IDX_SYS_CTRL/2 enum
mfd: stmpe: Add reset support for all STMPE variant
gpio: stmpe: fix edge and rising/falling edge detection
gpio: stmpe: write int status register only when needed
mfd: stmpe: use generic bit mask name
mfd: stmpe: rework registers access
gpio: stmpe: rework registers access
Documentation: dt: add stmpe1600 compatible string to stmpe mfd
mfd: Add STMPE1600 support
gpio: stmpe: Add STMPE1600 support
Documentation/devicetree/bindings/mfd/stmpe.txt | 2 +-
drivers/gpio/gpio-stmpe.c | 167 +++++++++++++++++-------
drivers/mfd/stmpe-i2c.c | 2 +
drivers/mfd/stmpe.c | 161 +++++++++++++++++++----
drivers/mfd/stmpe.h | 85 ++++++++++--
include/linux/mfd/stmpe.h | 21 +++
6 files changed, 352 insertions(+), 86 deletions(-)
--
1.9.1
From: Patrice Chotard <[email protected]>
STMPE1600 is a 16-bit port expander.
Datasheet is available here :
http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/
i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html
Signed-off-by: Amelie DELAUNAY <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
Acked-by: Linus Walleij <[email protected]>
---
drivers/mfd/stmpe-i2c.c | 2 ++
drivers/mfd/stmpe.c | 65 +++++++++++++++++++++++++++++++++++++++++++----
drivers/mfd/stmpe.h | 21 +++++++++++++++
include/linux/mfd/stmpe.h | 1 +
4 files changed, 84 insertions(+), 5 deletions(-)
diff --git a/drivers/mfd/stmpe-i2c.c b/drivers/mfd/stmpe-i2c.c
index c3f4aab..863c39a 100644
--- a/drivers/mfd/stmpe-i2c.c
+++ b/drivers/mfd/stmpe-i2c.c
@@ -57,6 +57,7 @@ static const struct of_device_id stmpe_of_match[] = {
{ .compatible = "st,stmpe610", .data = (void *)STMPE610, },
{ .compatible = "st,stmpe801", .data = (void *)STMPE801, },
{ .compatible = "st,stmpe811", .data = (void *)STMPE811, },
+ { .compatible = "st,stmpe1600", .data = (void *)STMPE1600, },
{ .compatible = "st,stmpe1601", .data = (void *)STMPE1601, },
{ .compatible = "st,stmpe1801", .data = (void *)STMPE1801, },
{ .compatible = "st,stmpe2401", .data = (void *)STMPE2401, },
@@ -101,6 +102,7 @@ static const struct i2c_device_id stmpe_i2c_id[] = {
{ "stmpe610", STMPE610 },
{ "stmpe801", STMPE801 },
{ "stmpe811", STMPE811 },
+ { "stmpe1600", STMPE1600 },
{ "stmpe1601", STMPE1601 },
{ "stmpe1801", STMPE1801 },
{ "stmpe2401", STMPE2401 },
diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index a060809..3a65331 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -532,6 +532,59 @@ static struct stmpe_variant_info stmpe610 = {
};
/*
+ * STMPE1600
+ * Compared to all others STMPE variant, LSB and MSB regs are located in this
+ * order : LSB addr
+ * MSB addr + 1
+ * As there is only 2 * 8bits registers for GPMR/GPSR/IEGPIOPR, CSB index is MSB registers
+ */
+
+static const u8 stmpe1600_regs[] = {
+ [STMPE_IDX_CHIP_ID] = STMPE1600_REG_CHIP_ID,
+ [STMPE_IDX_SYS_CTRL] = STMPE1600_REG_SYS_CTRL,
+ [STMPE_IDX_ICR_LSB] = STMPE1600_REG_SYS_CTRL,
+ [STMPE_IDX_GPMR_LSB] = STMPE1600_REG_GPMR_LSB,
+ [STMPE_IDX_GPMR_CSB] = STMPE1600_REG_GPMR_MSB,
+ [STMPE_IDX_GPSR_LSB] = STMPE1600_REG_GPSR_LSB,
+ [STMPE_IDX_GPSR_CSB] = STMPE1600_REG_GPSR_MSB,
+ [STMPE_IDX_GPDR_LSB] = STMPE1600_REG_GPDR_LSB,
+ [STMPE_IDX_GPDR_CSB] = STMPE1600_REG_GPDR_MSB,
+ [STMPE_IDX_IEGPIOR_LSB] = STMPE1600_REG_IEGPIOR_LSB,
+ [STMPE_IDX_IEGPIOR_CSB] = STMPE1600_REG_IEGPIOR_MSB,
+ [STMPE_IDX_ISGPIOR_LSB] = STMPE1600_REG_ISGPIOR_LSB,
+};
+
+static struct stmpe_variant_block stmpe1600_blocks[] = {
+ {
+ .cell = &stmpe_gpio_cell,
+ .irq = 0,
+ .block = STMPE_BLOCK_GPIO,
+ },
+};
+
+static int stmpe1600_enable(struct stmpe *stmpe, unsigned int blocks,
+ bool enable)
+{
+ if (blocks & STMPE_BLOCK_GPIO)
+ return 0;
+ else
+ return -EINVAL;
+}
+
+static struct stmpe_variant_info stmpe1600 = {
+ .name = "stmpe1600",
+ .id_val = STMPE1600_ID,
+ .id_mask = 0xffff,
+ .num_gpios = 16,
+ .af_bits = 0,
+ .regs = stmpe1600_regs,
+ .blocks = stmpe1600_blocks,
+ .num_blocks = ARRAY_SIZE(stmpe1600_blocks),
+ .num_irqs = STMPE1600_NR_INTERNAL_IRQS,
+ .enable = stmpe1600_enable,
+};
+
+/*
* STMPE1601
*/
@@ -928,6 +981,7 @@ static struct stmpe_variant_info *stmpe_variant_info[STMPE_NBR_PARTS] = {
[STMPE610] = &stmpe610,
[STMPE801] = &stmpe801,
[STMPE811] = &stmpe811,
+ [STMPE1600] = &stmpe1600,
[STMPE1601] = &stmpe1601,
[STMPE1801] = &stmpe1801,
[STMPE2401] = &stmpe2401,
@@ -954,7 +1008,8 @@ static irqreturn_t stmpe_irq(int irq, void *data)
int ret;
int i;
- if (variant->id_val == STMPE801_ID) {
+ if (variant->id_val == STMPE801_ID ||
+ variant->id_val == STMPE1600_ID) {
int base = irq_create_mapping(stmpe->domain, 0);
handle_nested_irq(base);
@@ -1128,13 +1183,13 @@ static int stmpe_chip_init(struct stmpe *stmpe)
return ret;
if (stmpe->irq >= 0) {
- if (id == STMPE801_ID)
+ if (id == STMPE801_ID || id == STMPE1600_ID)
icr = STMPE_SYS_CTRL_INT_EN;
else
icr = STMPE_ICR_LSB_GIM;
- /* STMPE801 doesn't support Edge interrupts */
- if (id != STMPE801_ID) {
+ /* STMPE801 and STMPE1600 don't support Edge interrupts */
+ if (id != STMPE801_ID && id != STMPE1600_ID) {
if (irq_trigger == IRQF_TRIGGER_FALLING ||
irq_trigger == IRQF_TRIGGER_RISING)
icr |= STMPE_ICR_LSB_EDGE;
@@ -1142,7 +1197,7 @@ static int stmpe_chip_init(struct stmpe *stmpe)
if (irq_trigger == IRQF_TRIGGER_RISING ||
irq_trigger == IRQF_TRIGGER_HIGH) {
- if (id == STMPE801_ID)
+ if (id == STMPE801_ID || id == STMPE1600_ID)
icr |= STMPE_SYS_CTRL_INT_HI;
else
icr |= STMPE_ICR_LSB_HIGH;
diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h
index f127342..f7efdd8 100644
--- a/drivers/mfd/stmpe.h
+++ b/drivers/mfd/stmpe.h
@@ -164,6 +164,27 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE811_SYS_CTRL2_TS_OFF (1 << 3)
/*
+ * STMPE1600
+ */
+#define STMPE1600_ID 0x0016
+#define STMPE1600_NR_INTERNAL_IRQS 16
+
+#define STMPE1600_REG_CHIP_ID 0x00
+#define STMPE1600_REG_SYS_CTRL 0x03
+#define STMPE1600_REG_IEGPIOR_LSB 0x08
+#define STMPE1600_REG_IEGPIOR_MSB 0x09
+#define STMPE1600_REG_ISGPIOR_LSB 0x0A
+#define STMPE1600_REG_ISGPIOR_MSB 0x0B
+#define STMPE1600_REG_GPMR_LSB 0x10
+#define STMPE1600_REG_GPMR_MSB 0x11
+#define STMPE1600_REG_GPSR_LSB 0x12
+#define STMPE1600_REG_GPSR_MSB 0x13
+#define STMPE1600_REG_GPDR_LSB 0x14
+#define STMPE1600_REG_GPDR_MSB 0x15
+#define STMPE1600_REG_GPPIR_LSB 0x16
+#define STMPE1600_REG_GPPIR_MSB 0x17
+
+/*
* STMPE1601
*/
diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h
index 3dced4a..0170bd6 100644
--- a/include/linux/mfd/stmpe.h
+++ b/include/linux/mfd/stmpe.h
@@ -26,6 +26,7 @@ enum stmpe_partnum {
STMPE610,
STMPE801,
STMPE811,
+ STMPE1600,
STMPE1601,
STMPE1801,
STMPE2401,
--
1.9.1
From: Patrice Chotard <[email protected]>
The particularities of this variant are:
- GPIO_XXX_LSB and GPIO_XXX_MSB memory locations are inverted compared
to other variants.
- There is no Edge detection, Rising Edge and Falling Edge registers.
- IRQ flags are cleared when read, no need to write in Status register.
Signed-off-by: Amelie DELAUNAY <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
---
drivers/gpio/gpio-stmpe.c | 48 +++++++++++++++++++++++++++++++++++++----------
1 file changed, 38 insertions(+), 10 deletions(-)
diff --git a/drivers/gpio/gpio-stmpe.c b/drivers/gpio/gpio-stmpe.c
index 6d6d76a..32c5a72 100644
--- a/drivers/gpio/gpio-stmpe.c
+++ b/drivers/gpio/gpio-stmpe.c
@@ -128,8 +128,9 @@ static int stmpe_gpio_irq_set_type(struct irq_data *d, unsigned int type)
if (type & IRQ_TYPE_LEVEL_LOW || type & IRQ_TYPE_LEVEL_HIGH)
return -EINVAL;
- /* STMPE801 doesn't have RE and FE registers */
- if (stmpe_gpio->stmpe->partnum == STMPE801)
+ /* STMPE801 and STMPE 1600 don't have RE and FE registers */
+ if (stmpe_gpio->stmpe->partnum == STMPE801 ||
+ stmpe_gpio->stmpe->partnum == STMPE1600)
return 0;
if (type & IRQ_TYPE_EDGE_RISING)
@@ -173,9 +174,10 @@ static void stmpe_gpio_irq_sync_unlock(struct irq_data *d)
int i, j;
for (i = 0; i < CACHE_NR_REGS; i++) {
- /* STMPE801 doesn't have RE and FE registers */
- if ((stmpe->partnum == STMPE801) &&
- (i != REG_IE))
+ /* STMPE801 and STMPE1600 don't have RE and FE registers */
+ if ((stmpe->partnum == STMPE801 ||
+ stmpe->partnum == STMPE1600) &&
+ (i != REG_IE))
continue;
for (j = 0; j < num_banks; j++) {
@@ -208,11 +210,21 @@ static void stmpe_gpio_irq_unmask(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(gc);
+ struct stmpe *stmpe = stmpe_gpio->stmpe;
int offset = d->hwirq;
int regoffset = offset / 8;
int mask = 1 << (offset % 8);
stmpe_gpio->regs[REG_IE][regoffset] |= mask;
+
+ /*
+ * STMPE1600 workaround: to be able to get IRQ from pins,
+ * a read must be done on GPMR register, or a write in
+ * GPSR or GPCR registers
+ */
+ if (stmpe->partnum == STMPE1600)
+ stmpe_reg_read(stmpe,
+ stmpe->regs[STMPE_IDX_GPMR_LSB + regoffset]);
}
static void stmpe_dbg_show_one(struct seq_file *s,
@@ -285,6 +297,7 @@ static void stmpe_dbg_show_one(struct seq_file *s,
fall = !!(ret & mask);
case STMPE801:
+ case STMPE1600:
irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB + bank];
break;
@@ -331,18 +344,32 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
{
struct stmpe_gpio *stmpe_gpio = dev;
struct stmpe *stmpe = stmpe_gpio->stmpe;
- u8 statmsbreg = stmpe->regs[STMPE_IDX_ISGPIOR_MSB];
+ u8 statmsbreg;
int num_banks = DIV_ROUND_UP(stmpe->num_gpios, 8);
u8 status[num_banks];
int ret;
int i;
+ /*
+ * the stmpe_block_read() call below, imposes to set statmsbreg
+ * with the register located at the lowest address. As STMPE1600
+ * variant is the only one which respect registers address's order
+ * (LSB regs located at lowest address than MSB ones) whereas all
+ * the others have a registers layout with MSB located before the
+ * LSB regs.
+ */
+ if (stmpe->partnum == STMPE1600)
+ statmsbreg = stmpe->regs[STMPE_IDX_ISGPIOR_LSB];
+ else
+ statmsbreg = stmpe->regs[STMPE_IDX_ISGPIOR_MSB];
+
ret = stmpe_block_read(stmpe, statmsbreg, num_banks, status);
if (ret < 0)
return IRQ_NONE;
for (i = 0; i < num_banks; i++) {
- int bank = num_banks - i - 1;
+ int bank = (stmpe_gpio->stmpe->partnum == STMPE1600) ? i :
+ num_banks - i - 1;
unsigned int enabled = stmpe_gpio->regs[REG_IE][bank];
unsigned int stat = status[i];
@@ -362,10 +389,11 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
/*
* interrupt status register write has no effect on
- * 801 and 1801, bits are cleared when read.
- * Edge detect register is not present on 801 and 1801
+ * 801/1801/1600, bits are cleared when read.
+ * Edge detect register is not present on 801/1600/1801
*/
- if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1801) {
+ if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1600 ||
+ stmpe->partnum != STMPE1801) {
stmpe_reg_write(stmpe, statmsbreg + i, status[i]);
stmpe_reg_write(stmpe,
stmpe->regs[STMPE_IDX_GPEDR_LSB + i],
--
1.9.1
From: Patrice Chotard <[email protected]>
On STMPE801/1801 datasheets, it's mentionned writing
in interrupt status register has no effect, bits are
cleared when reading.
Signed-off-by: Amelie DELAUNAY <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
---
drivers/gpio/gpio-stmpe.c | 12 ++++++++----
1 file changed, 8 insertions(+), 4 deletions(-)
diff --git a/drivers/gpio/gpio-stmpe.c b/drivers/gpio/gpio-stmpe.c
index bfc918c..2789bdc 100644
--- a/drivers/gpio/gpio-stmpe.c
+++ b/drivers/gpio/gpio-stmpe.c
@@ -355,12 +355,16 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
stat &= ~(1 << bit);
}
- stmpe_reg_write(stmpe, statmsbreg + i, status[i]);
-
- /* Edge detect register is not present on 801 and 1801 */
- if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1801)
+ /*
+ * interrupt status register write has no effect on
+ * 801 and 1801, bits are cleared when read.
+ * Edge detect register is not present on 801 and 1801
+ */
+ if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1801) {
+ stmpe_reg_write(stmpe, statmsbreg + i, status[i]);
stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_GPEDR_MSB]
+ i, status[i]);
+ }
}
return IRQ_HANDLED;
--
1.9.1
From: Patrice Chotard <[email protected]>
As STMPE1801/1601/24xx has a SYS_CTRL register and
STMPE1601/2403 has even a SYS_CTRL2 register, add
STMPE_IDX_SYS_CTRL/2 and update driver code accordingly
This update prepares the ground for not yet supported STMPE1600
which share similar REG_SYS_CTRL register.
Signed-off-by: Patrice Chotard <[email protected]>
Acked-by: Linus Walleij <[email protected]>
Acked-by: Lee Jones <[email protected]>
---
drivers/mfd/stmpe.c | 21 ++++++++++++++-------
drivers/mfd/stmpe.h | 2 ++
include/linux/mfd/stmpe.h | 2 ++
3 files changed, 18 insertions(+), 7 deletions(-)
diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index fb8f9e8..c553b73 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -448,6 +448,8 @@ static const struct mfd_cell stmpe_ts_cell = {
static const u8 stmpe811_regs[] = {
[STMPE_IDX_CHIP_ID] = STMPE811_REG_CHIP_ID,
+ [STMPE_IDX_SYS_CTRL] = STMPE811_REG_SYS_CTRL,
+ [STMPE_IDX_SYS_CTRL2] = STMPE811_REG_SYS_CTRL2,
[STMPE_IDX_ICR_LSB] = STMPE811_REG_INT_CTRL,
[STMPE_IDX_IER_LSB] = STMPE811_REG_INT_EN,
[STMPE_IDX_ISR_MSB] = STMPE811_REG_INT_STA,
@@ -490,7 +492,7 @@ static int stmpe811_enable(struct stmpe *stmpe, unsigned int blocks,
if (blocks & STMPE_BLOCK_TOUCHSCREEN)
mask |= STMPE811_SYS_CTRL2_TSC_OFF;
- return __stmpe_set_bits(stmpe, STMPE811_REG_SYS_CTRL2, mask,
+ return __stmpe_set_bits(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL2], mask,
enable ? 0 : mask);
}
@@ -535,6 +537,8 @@ static struct stmpe_variant_info stmpe610 = {
static const u8 stmpe1601_regs[] = {
[STMPE_IDX_CHIP_ID] = STMPE1601_REG_CHIP_ID,
+ [STMPE_IDX_SYS_CTRL] = STMPE1601_REG_SYS_CTRL,
+ [STMPE_IDX_SYS_CTRL2] = STMPE1601_REG_SYS_CTRL2,
[STMPE_IDX_ICR_LSB] = STMPE1601_REG_ICR_LSB,
[STMPE_IDX_IER_LSB] = STMPE1601_REG_IER_LSB,
[STMPE_IDX_ISR_MSB] = STMPE1601_REG_ISR_MSB,
@@ -619,13 +623,13 @@ static int stmpe1601_autosleep(struct stmpe *stmpe,
return timeout;
}
- ret = __stmpe_set_bits(stmpe, STMPE1601_REG_SYS_CTRL2,
+ ret = __stmpe_set_bits(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL2],
STMPE1601_AUTOSLEEP_TIMEOUT_MASK,
timeout);
if (ret < 0)
return ret;
- return __stmpe_set_bits(stmpe, STMPE1601_REG_SYS_CTRL2,
+ return __stmpe_set_bits(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL2],
STPME1601_AUTOSLEEP_ENABLE,
STPME1601_AUTOSLEEP_ENABLE);
}
@@ -650,7 +654,7 @@ static int stmpe1601_enable(struct stmpe *stmpe, unsigned int blocks,
else
mask &= ~STMPE1601_SYS_CTRL_ENABLE_SPWM;
- return __stmpe_set_bits(stmpe, STMPE1601_REG_SYS_CTRL, mask,
+ return __stmpe_set_bits(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL], mask,
enable ? mask : 0);
}
@@ -689,6 +693,7 @@ static struct stmpe_variant_info stmpe1601 = {
*/
static const u8 stmpe1801_regs[] = {
[STMPE_IDX_CHIP_ID] = STMPE1801_REG_CHIP_ID,
+ [STMPE_IDX_SYS_CTRL] = STMPE1801_REG_SYS_CTRL,
[STMPE_IDX_ICR_LSB] = STMPE1801_REG_INT_CTRL_LOW,
[STMPE_IDX_IER_LSB] = STMPE1801_REG_INT_EN_MASK_LOW,
[STMPE_IDX_ISR_LSB] = STMPE1801_REG_INT_STA_LOW,
@@ -735,14 +740,14 @@ static int stmpe1801_reset(struct stmpe *stmpe)
unsigned long timeout;
int ret = 0;
- ret = __stmpe_set_bits(stmpe, STMPE1801_REG_SYS_CTRL,
+ ret = __stmpe_set_bits(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL],
STMPE1801_MSK_SYS_CTRL_RESET, STMPE1801_MSK_SYS_CTRL_RESET);
if (ret < 0)
return ret;
timeout = jiffies + msecs_to_jiffies(100);
while (time_before(jiffies, timeout)) {
- ret = __stmpe_reg_read(stmpe, STMPE1801_REG_SYS_CTRL);
+ ret = __stmpe_reg_read(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL]);
if (ret < 0)
return ret;
if (!(ret & STMPE1801_MSK_SYS_CTRL_RESET))
@@ -773,6 +778,8 @@ static struct stmpe_variant_info stmpe1801 = {
static const u8 stmpe24xx_regs[] = {
[STMPE_IDX_CHIP_ID] = STMPE24XX_REG_CHIP_ID,
+ [STMPE_IDX_SYS_CTRL] = STMPE24XX_REG_SYS_CTRL,
+ [STMPE_IDX_SYS_CTRL2] = STMPE24XX_REG_SYS_CTRL2,
[STMPE_IDX_ICR_LSB] = STMPE24XX_REG_ICR_LSB,
[STMPE_IDX_IER_LSB] = STMPE24XX_REG_IER_LSB,
[STMPE_IDX_ISR_MSB] = STMPE24XX_REG_ISR_MSB,
@@ -819,7 +826,7 @@ static int stmpe24xx_enable(struct stmpe *stmpe, unsigned int blocks,
if (blocks & STMPE_BLOCK_KEYPAD)
mask |= STMPE24XX_SYS_CTRL_ENABLE_KPC;
- return __stmpe_set_bits(stmpe, STMPE24XX_REG_SYS_CTRL, mask,
+ return __stmpe_set_bits(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL], mask,
enable ? mask : 0);
}
diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h
index 84adb46..406f9f2 100644
--- a/drivers/mfd/stmpe.h
+++ b/drivers/mfd/stmpe.h
@@ -138,6 +138,7 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE811_NR_INTERNAL_IRQS 8
#define STMPE811_REG_CHIP_ID 0x00
+#define STMPE811_REG_SYS_CTRL 0x03
#define STMPE811_REG_SYS_CTRL2 0x04
#define STMPE811_REG_SPI_CFG 0x08
#define STMPE811_REG_INT_CTRL 0x09
@@ -264,6 +265,7 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE24XX_NR_INTERNAL_IRQS 9
#define STMPE24XX_REG_SYS_CTRL 0x02
+#define STMPE24XX_REG_SYS_CTRL2 0x03
#define STMPE24XX_REG_ICR_LSB 0x11
#define STMPE24XX_REG_IER_LSB 0x13
#define STMPE24XX_REG_ISR_MSB 0x14
diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h
index cb83883..6c6690f 100644
--- a/include/linux/mfd/stmpe.h
+++ b/include/linux/mfd/stmpe.h
@@ -39,6 +39,8 @@ enum stmpe_partnum {
*/
enum {
STMPE_IDX_CHIP_ID,
+ STMPE_IDX_SYS_CTRL,
+ STMPE_IDX_SYS_CTRL2,
STMPE_IDX_ICR_LSB,
STMPE_IDX_IER_LSB,
STMPE_IDX_ISR_LSB,
--
1.9.1
From: Patrice Chotard <[email protected]>
this update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset
This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.
For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: Patrice Chotard <[email protected]>
---
drivers/mfd/stmpe.c | 48 ++++++++++++++++++++++++++++++++++++++++++----
drivers/mfd/stmpe.h | 49 +++++++++++++++++++++++++++++++++++++++++------
include/linux/mfd/stmpe.h | 18 +++++++++++++++++
3 files changed, 105 insertions(+), 10 deletions(-)
diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index 2556463..a060809 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -462,7 +462,7 @@ static const u8 stmpe811_regs[] = {
[STMPE_IDX_GPAFR_U_MSB] = STMPE811_REG_GPIO_AF,
[STMPE_IDX_IEGPIOR_LSB] = STMPE811_REG_GPIO_INT_EN,
[STMPE_IDX_ISGPIOR_MSB] = STMPE811_REG_GPIO_INT_STA,
- [STMPE_IDX_GPEDR_MSB] = STMPE811_REG_GPIO_ED,
+ [STMPE_IDX_GPEDR_LSB] = STMPE811_REG_GPIO_ED,
};
static struct stmpe_variant_block stmpe811_blocks[] = {
@@ -540,19 +540,28 @@ static const u8 stmpe1601_regs[] = {
[STMPE_IDX_SYS_CTRL] = STMPE1601_REG_SYS_CTRL,
[STMPE_IDX_SYS_CTRL2] = STMPE1601_REG_SYS_CTRL2,
[STMPE_IDX_ICR_LSB] = STMPE1601_REG_ICR_LSB,
+ [STMPE_IDX_IER_MSB] = STMPE1601_REG_IER_MSB,
[STMPE_IDX_IER_LSB] = STMPE1601_REG_IER_LSB,
[STMPE_IDX_ISR_MSB] = STMPE1601_REG_ISR_MSB,
[STMPE_IDX_GPMR_LSB] = STMPE1601_REG_GPIO_MP_LSB,
+ [STMPE_IDX_GPMR_CSB] = STMPE1601_REG_GPIO_MP_MSB,
[STMPE_IDX_GPSR_LSB] = STMPE1601_REG_GPIO_SET_LSB,
+ [STMPE_IDX_GPSR_CSB] = STMPE1601_REG_GPIO_SET_MSB,
[STMPE_IDX_GPCR_LSB] = STMPE1601_REG_GPIO_CLR_LSB,
+ [STMPE_IDX_GPCR_CSB] = STMPE1601_REG_GPIO_CLR_MSB,
[STMPE_IDX_GPDR_LSB] = STMPE1601_REG_GPIO_SET_DIR_LSB,
+ [STMPE_IDX_GPDR_CSB] = STMPE1601_REG_GPIO_SET_DIR_MSB,
+ [STMPE_IDX_GPEDR_LSB] = STMPE1601_REG_GPIO_ED_LSB,
+ [STMPE_IDX_GPEDR_CSB] = STMPE1601_REG_GPIO_ED_MSB,
[STMPE_IDX_GPRER_LSB] = STMPE1601_REG_GPIO_RE_LSB,
+ [STMPE_IDX_GPRER_CSB] = STMPE1601_REG_GPIO_RE_MSB,
[STMPE_IDX_GPFER_LSB] = STMPE1601_REG_GPIO_FE_LSB,
+ [STMPE_IDX_GPFER_CSB] = STMPE1601_REG_GPIO_FE_MSB,
[STMPE_IDX_GPPUR_LSB] = STMPE1601_REG_GPIO_PU_LSB,
[STMPE_IDX_GPAFR_U_MSB] = STMPE1601_REG_GPIO_AF_U_MSB,
[STMPE_IDX_IEGPIOR_LSB] = STMPE1601_REG_INT_EN_GPIO_MASK_LSB,
+ [STMPE_IDX_IEGPIOR_CSB] = STMPE1601_REG_INT_EN_GPIO_MASK_MSB,
[STMPE_IDX_ISGPIOR_MSB] = STMPE1601_REG_INT_STA_GPIO_MSB,
- [STMPE_IDX_GPEDR_MSB] = STMPE1601_REG_GPIO_ED_MSB,
};
static struct stmpe_variant_block stmpe1601_blocks[] = {
@@ -698,14 +707,28 @@ static const u8 stmpe1801_regs[] = {
[STMPE_IDX_IER_LSB] = STMPE1801_REG_INT_EN_MASK_LOW,
[STMPE_IDX_ISR_LSB] = STMPE1801_REG_INT_STA_LOW,
[STMPE_IDX_GPMR_LSB] = STMPE1801_REG_GPIO_MP_LOW,
+ [STMPE_IDX_GPMR_CSB] = STMPE1801_REG_GPIO_MP_MID,
+ [STMPE_IDX_GPMR_MSB] = STMPE1801_REG_GPIO_MP_HIGH,
[STMPE_IDX_GPSR_LSB] = STMPE1801_REG_GPIO_SET_LOW,
+ [STMPE_IDX_GPSR_CSB] = STMPE1801_REG_GPIO_SET_MID,
+ [STMPE_IDX_GPSR_MSB] = STMPE1801_REG_GPIO_SET_HIGH,
[STMPE_IDX_GPCR_LSB] = STMPE1801_REG_GPIO_CLR_LOW,
+ [STMPE_IDX_GPCR_CSB] = STMPE1801_REG_GPIO_CLR_MID,
+ [STMPE_IDX_GPCR_MSB] = STMPE1801_REG_GPIO_CLR_HIGH,
[STMPE_IDX_GPDR_LSB] = STMPE1801_REG_GPIO_SET_DIR_LOW,
+ [STMPE_IDX_GPDR_CSB] = STMPE1801_REG_GPIO_SET_DIR_MID,
+ [STMPE_IDX_GPDR_MSB] = STMPE1801_REG_GPIO_SET_DIR_HIGH,
[STMPE_IDX_GPRER_LSB] = STMPE1801_REG_GPIO_RE_LOW,
+ [STMPE_IDX_GPRER_CSB] = STMPE1801_REG_GPIO_RE_MID,
+ [STMPE_IDX_GPRER_MSB] = STMPE1801_REG_GPIO_RE_HIGH,
[STMPE_IDX_GPFER_LSB] = STMPE1801_REG_GPIO_FE_LOW,
+ [STMPE_IDX_GPFER_CSB] = STMPE1801_REG_GPIO_FE_MID,
+ [STMPE_IDX_GPFER_MSB] = STMPE1801_REG_GPIO_FE_HIGH,
[STMPE_IDX_GPPUR_LSB] = STMPE1801_REG_GPIO_PULL_UP_LOW,
[STMPE_IDX_IEGPIOR_LSB] = STMPE1801_REG_INT_EN_GPIO_MASK_LOW,
- [STMPE_IDX_ISGPIOR_LSB] = STMPE1801_REG_INT_STA_GPIO_LOW,
+ [STMPE_IDX_IEGPIOR_CSB] = STMPE1801_REG_INT_EN_GPIO_MASK_MID,
+ [STMPE_IDX_IEGPIOR_MSB] = STMPE1801_REG_INT_EN_GPIO_MASK_HIGH,
+ [STMPE_IDX_ISGPIOR_MSB] = STMPE1801_REG_INT_STA_GPIO_HIGH,
};
static struct stmpe_variant_block stmpe1801_blocks[] = {
@@ -790,19 +813,36 @@ static const u8 stmpe24xx_regs[] = {
[STMPE_IDX_SYS_CTRL] = STMPE24XX_REG_SYS_CTRL,
[STMPE_IDX_SYS_CTRL2] = STMPE24XX_REG_SYS_CTRL2,
[STMPE_IDX_ICR_LSB] = STMPE24XX_REG_ICR_LSB,
+ [STMPE_IDX_IER_MSB] = STMPE24XX_REG_IER_MSB,
[STMPE_IDX_IER_LSB] = STMPE24XX_REG_IER_LSB,
[STMPE_IDX_ISR_MSB] = STMPE24XX_REG_ISR_MSB,
[STMPE_IDX_GPMR_LSB] = STMPE24XX_REG_GPMR_LSB,
+ [STMPE_IDX_GPMR_CSB] = STMPE24XX_REG_GPMR_CSB,
+ [STMPE_IDX_GPMR_MSB] = STMPE24XX_REG_GPMR_MSB,
[STMPE_IDX_GPSR_LSB] = STMPE24XX_REG_GPSR_LSB,
+ [STMPE_IDX_GPSR_CSB] = STMPE24XX_REG_GPSR_CSB,
+ [STMPE_IDX_GPSR_MSB] = STMPE24XX_REG_GPSR_MSB,
[STMPE_IDX_GPCR_LSB] = STMPE24XX_REG_GPCR_LSB,
+ [STMPE_IDX_GPCR_CSB] = STMPE24XX_REG_GPCR_CSB,
+ [STMPE_IDX_GPCR_MSB] = STMPE24XX_REG_GPCR_MSB,
[STMPE_IDX_GPDR_LSB] = STMPE24XX_REG_GPDR_LSB,
+ [STMPE_IDX_GPDR_CSB] = STMPE24XX_REG_GPDR_CSB,
+ [STMPE_IDX_GPDR_MSB] = STMPE24XX_REG_GPDR_MSB,
[STMPE_IDX_GPRER_LSB] = STMPE24XX_REG_GPRER_LSB,
+ [STMPE_IDX_GPRER_CSB] = STMPE24XX_REG_GPRER_CSB,
+ [STMPE_IDX_GPRER_MSB] = STMPE24XX_REG_GPRER_MSB,
[STMPE_IDX_GPFER_LSB] = STMPE24XX_REG_GPFER_LSB,
+ [STMPE_IDX_GPFER_CSB] = STMPE24XX_REG_GPFER_CSB,
+ [STMPE_IDX_GPFER_MSB] = STMPE24XX_REG_GPFER_MSB,
[STMPE_IDX_GPPUR_LSB] = STMPE24XX_REG_GPPUR_LSB,
[STMPE_IDX_GPPDR_LSB] = STMPE24XX_REG_GPPDR_LSB,
[STMPE_IDX_GPAFR_U_MSB] = STMPE24XX_REG_GPAFR_U_MSB,
[STMPE_IDX_IEGPIOR_LSB] = STMPE24XX_REG_IEGPIOR_LSB,
+ [STMPE_IDX_IEGPIOR_CSB] = STMPE24XX_REG_IEGPIOR_CSB,
+ [STMPE_IDX_IEGPIOR_MSB] = STMPE24XX_REG_IEGPIOR_MSB,
[STMPE_IDX_ISGPIOR_MSB] = STMPE24XX_REG_ISGPIOR_MSB,
+ [STMPE_IDX_GPEDR_LSB] = STMPE24XX_REG_GPEDR_LSB,
+ [STMPE_IDX_GPEDR_CSB] = STMPE24XX_REG_GPEDR_CSB,
[STMPE_IDX_GPEDR_MSB] = STMPE24XX_REG_GPEDR_MSB,
};
@@ -977,7 +1017,7 @@ static void stmpe_irq_sync_unlock(struct irq_data *data)
continue;
stmpe->oldier[i] = new;
- stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_IER_LSB] - i, new);
+ stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_IER_LSB + i], new);
}
mutex_unlock(&stmpe->irq_lock);
diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h
index 4ba1123..f127342 100644
--- a/drivers/mfd/stmpe.h
+++ b/drivers/mfd/stmpe.h
@@ -179,19 +179,32 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE1601_REG_SYS_CTRL 0x02
#define STMPE1601_REG_SYS_CTRL2 0x03
+#define STMPE1601_REG_ICR_MSB 0x10
#define STMPE1601_REG_ICR_LSB 0x11
+#define STMPE1601_REG_IER_MSB 0x12
#define STMPE1601_REG_IER_LSB 0x13
#define STMPE1601_REG_ISR_MSB 0x14
-#define STMPE1601_REG_CHIP_ID 0x80
+#define STMPE1601_REG_ISR_LSB 0x15
+#define STMPE1601_REG_INT_EN_GPIO_MASK_MSB 0x16
#define STMPE1601_REG_INT_EN_GPIO_MASK_LSB 0x17
#define STMPE1601_REG_INT_STA_GPIO_MSB 0x18
-#define STMPE1601_REG_GPIO_MP_LSB 0x87
+#define STMPE1601_REG_INT_STA_GPIO_LSB 0x19
+#define STMPE1601_REG_CHIP_ID 0x80
+#define STMPE1601_REG_GPIO_SET_MSB 0x82
#define STMPE1601_REG_GPIO_SET_LSB 0x83
+#define STMPE1601_REG_GPIO_CLR_MSB 0x84
#define STMPE1601_REG_GPIO_CLR_LSB 0x85
+#define STMPE1601_REG_GPIO_MP_MSB 0x86
+#define STMPE1601_REG_GPIO_MP_LSB 0x87
+#define STMPE1601_REG_GPIO_SET_DIR_MSB 0x88
#define STMPE1601_REG_GPIO_SET_DIR_LSB 0x89
#define STMPE1601_REG_GPIO_ED_MSB 0x8A
+#define STMPE1601_REG_GPIO_ED_LSB 0x8B
+#define STMPE1601_REG_GPIO_RE_MSB 0x8C
#define STMPE1601_REG_GPIO_RE_LSB 0x8D
+#define STMPE1601_REG_GPIO_FE_MSB 0x8E
#define STMPE1601_REG_GPIO_FE_LSB 0x8F
+#define STMPE1601_REG_GPIO_PU_MSB 0x90
#define STMPE1601_REG_GPIO_PU_LSB 0x91
#define STMPE1601_REG_GPIO_AF_U_MSB 0x92
@@ -267,23 +280,47 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE24XX_REG_SYS_CTRL 0x02
#define STMPE24XX_REG_SYS_CTRL2 0x03
+#define STMPE24XX_REG_ICR_MSB 0x10
#define STMPE24XX_REG_ICR_LSB 0x11
+#define STMPE24XX_REG_IER_MSB 0x12
#define STMPE24XX_REG_IER_LSB 0x13
#define STMPE24XX_REG_ISR_MSB 0x14
-#define STMPE24XX_REG_CHIP_ID 0x80
+#define STMPE24XX_REG_ISR_LSB 0x15
+#define STMPE24XX_REG_IEGPIOR_MSB 0x16
+#define STMPE24XX_REG_IEGPIOR_CSB 0x17
#define STMPE24XX_REG_IEGPIOR_LSB 0x18
#define STMPE24XX_REG_ISGPIOR_MSB 0x19
-#define STMPE24XX_REG_GPMR_LSB 0xA4
+#define STMPE24XX_REG_ISGPIOR_CSB 0x1A
+#define STMPE24XX_REG_ISGPIOR_LSB 0x1B
+#define STMPE24XX_REG_CHIP_ID 0x80
+#define STMPE24XX_REG_GPSR_MSB 0x83
+#define STMPE24XX_REG_GPSR_CSB 0x84
#define STMPE24XX_REG_GPSR_LSB 0x85
+#define STMPE24XX_REG_GPCR_MSB 0x86
+#define STMPE24XX_REG_GPCR_CSB 0x87
#define STMPE24XX_REG_GPCR_LSB 0x88
+#define STMPE24XX_REG_GPDR_MSB 0x89
+#define STMPE24XX_REG_GPDR_CSB 0x8A
#define STMPE24XX_REG_GPDR_LSB 0x8B
#define STMPE24XX_REG_GPEDR_MSB 0x8C
+#define STMPE24XX_REG_GPEDR_CSB 0x8D
+#define STMPE24XX_REG_GPEDR_LSB 0x8E
+#define STMPE24XX_REG_GPRER_MSB 0x8F
+#define STMPE24XX_REG_GPRER_CSB 0x90
#define STMPE24XX_REG_GPRER_LSB 0x91
+#define STMPE24XX_REG_GPFER_MSB 0x92
+#define STMPE24XX_REG_GPFER_CSB 0x93
#define STMPE24XX_REG_GPFER_LSB 0x94
+#define STMPE24XX_REG_GPPUR_MSB 0x95
+#define STMPE24XX_REG_GPPUR_CSB 0x96
#define STMPE24XX_REG_GPPUR_LSB 0x97
-#define STMPE24XX_REG_GPPDR_LSB 0x9a
+#define STMPE24XX_REG_GPPDR_MSB 0x98
+#define STMPE24XX_REG_GPPDR_CSB 0x99
+#define STMPE24XX_REG_GPPDR_LSB 0x9A
#define STMPE24XX_REG_GPAFR_U_MSB 0x9B
-
+#define STMPE24XX_REG_GPMR_MSB 0xA2
+#define STMPE24XX_REG_GPMR_CSB 0xA3
+#define STMPE24XX_REG_GPMR_LSB 0xA4
#define STMPE24XX_SYS_CTRL_ENABLE_GPIO (1 << 3)
#define STMPE24XX_SYSCON_ENABLE_PWM (1 << 2)
#define STMPE24XX_SYS_CTRL_ENABLE_KPC (1 << 1)
diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h
index 6c6690f..3dced4a 100644
--- a/include/linux/mfd/stmpe.h
+++ b/include/linux/mfd/stmpe.h
@@ -43,20 +43,38 @@ enum {
STMPE_IDX_SYS_CTRL2,
STMPE_IDX_ICR_LSB,
STMPE_IDX_IER_LSB,
+ STMPE_IDX_IER_MSB,
STMPE_IDX_ISR_LSB,
STMPE_IDX_ISR_MSB,
STMPE_IDX_GPMR_LSB,
+ STMPE_IDX_GPMR_CSB,
+ STMPE_IDX_GPMR_MSB,
STMPE_IDX_GPSR_LSB,
+ STMPE_IDX_GPSR_CSB,
+ STMPE_IDX_GPSR_MSB,
STMPE_IDX_GPCR_LSB,
+ STMPE_IDX_GPCR_CSB,
+ STMPE_IDX_GPCR_MSB,
STMPE_IDX_GPDR_LSB,
+ STMPE_IDX_GPDR_CSB,
+ STMPE_IDX_GPDR_MSB,
+ STMPE_IDX_GPEDR_LSB,
+ STMPE_IDX_GPEDR_CSB,
STMPE_IDX_GPEDR_MSB,
STMPE_IDX_GPRER_LSB,
+ STMPE_IDX_GPRER_CSB,
+ STMPE_IDX_GPRER_MSB,
STMPE_IDX_GPFER_LSB,
+ STMPE_IDX_GPFER_CSB,
+ STMPE_IDX_GPFER_MSB,
STMPE_IDX_GPPUR_LSB,
STMPE_IDX_GPPDR_LSB,
STMPE_IDX_GPAFR_U_MSB,
STMPE_IDX_IEGPIOR_LSB,
+ STMPE_IDX_IEGPIOR_CSB,
+ STMPE_IDX_IEGPIOR_MSB,
STMPE_IDX_ISGPIOR_LSB,
+ STMPE_IDX_ISGPIOR_CSB,
STMPE_IDX_ISGPIOR_MSB,
STMPE_IDX_MAX,
};
--
1.9.1
From: Patrice Chotard <[email protected]>
Reset was only implemented for STMPE1801 variant despite
all variant have a SOFT_RESET bit.
For STMPE2401/2403/801/1601/1801 SOFT_RESET bit is bit 7
of SYS_CTRL register.
For STMPE610/811 (which have the same variant id) SOFT_RESET
bit is bit 1 of SYS_CTRL register.
Signed-off-by: Patrice Chotard <[email protected]>
Acked-by: Linus Walleij <[email protected]>
Acked-by: Lee Jones <[email protected]>
---
drivers/mfd/stmpe.c | 23 +++++++++++++++--------
drivers/mfd/stmpe.h | 7 +++++--
2 files changed, 20 insertions(+), 10 deletions(-)
diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index c553b73..af682d0 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -735,13 +735,22 @@ static int stmpe1801_enable(struct stmpe *stmpe, unsigned int blocks,
enable ? mask : 0);
}
-static int stmpe1801_reset(struct stmpe *stmpe)
+static int stmpe_reset(struct stmpe *stmpe)
{
+ u16 id_val = stmpe->variant->id_val;
unsigned long timeout;
int ret = 0;
+ u8 reset_bit;
+
+ if (id_val == STMPE811_ID)
+ /* STMPE801 and STMPE610 use bit 1 of SYS_CTRL register */
+ reset_bit = STMPE811_SYS_CTRL_RESET;
+ else
+ /* all other STMPE variant use bit 7 of SYS_CTRL register */
+ reset_bit = STMPE_SYS_CTRL_RESET;
ret = __stmpe_set_bits(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL],
- STMPE1801_MSK_SYS_CTRL_RESET, STMPE1801_MSK_SYS_CTRL_RESET);
+ reset_bit, reset_bit);
if (ret < 0)
return ret;
@@ -750,7 +759,7 @@ static int stmpe1801_reset(struct stmpe *stmpe)
ret = __stmpe_reg_read(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL]);
if (ret < 0)
return ret;
- if (!(ret & STMPE1801_MSK_SYS_CTRL_RESET))
+ if (!(ret & reset_bit))
return 0;
usleep_range(100, 200);
}
@@ -1074,11 +1083,9 @@ static int stmpe_chip_init(struct stmpe *stmpe)
if (ret)
return ret;
- if (id == STMPE1801_ID) {
- ret = stmpe1801_reset(stmpe);
- if (ret < 0)
- return ret;
- }
+ ret = stmpe_reset(stmpe);
+ if (ret < 0)
+ return ret;
if (stmpe->irq >= 0) {
if (id == STMPE801_ID)
diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h
index 406f9f2..4ae343d 100644
--- a/drivers/mfd/stmpe.h
+++ b/drivers/mfd/stmpe.h
@@ -104,6 +104,8 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE_ICR_LSB_EDGE (1 << 1)
#define STMPE_ICR_LSB_GIM (1 << 0)
+#define STMPE_SYS_CTRL_RESET (1 << 7)
+
/*
* STMPE801
*/
@@ -126,6 +128,7 @@ int stmpe_remove(struct stmpe *stmpe);
/*
* STMPE811
*/
+#define STMPE811_ID 0x0811
#define STMPE811_IRQ_TOUCH_DET 0
#define STMPE811_IRQ_FIFO_TH 1
@@ -155,6 +158,8 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE811_REG_GPIO_FE 0x16
#define STMPE811_REG_GPIO_AF 0x17
+#define STMPE811_SYS_CTRL_RESET (1 << 1)
+
#define STMPE811_SYS_CTRL2_ADC_OFF (1 << 0)
#define STMPE811_SYS_CTRL2_TSC_OFF (1 << 1)
#define STMPE811_SYS_CTRL2_GPIO_OFF (1 << 2)
@@ -244,8 +249,6 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE1801_REG_GPIO_PULL_UP_MID 0x23
#define STMPE1801_REG_GPIO_PULL_UP_HIGH 0x24
-#define STMPE1801_MSK_SYS_CTRL_RESET (1 << 7)
-
#define STMPE1801_MSK_INT_EN_KPC (1 << 1)
#define STMPE1801_MSK_INT_EN_GPIO (1 << 3)
--
1.9.1
From: Patrice Chotard <[email protected]>
By cross-checking STMPE 610/801/811/1601/2401/2403 datasheets,
it appears that edge detection and rising/falling edge detection
is not supported by all STMPE variant:
GPIO GPIO
Edge detection rising/falling
edge detection
610 | X | X |
801 | | |
811 | X | X |
1600 | | |
1601 | X | X |
1801 | | X |
2401 | X | X |
2403 | X | X |
Rework stmpe_dbg_show_one() and stmpe_gpio_irq to correctly
take these cases into account.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
---
drivers/gpio/gpio-stmpe.c | 85 +++++++++++++++++++++++++++++++++--------------
1 file changed, 60 insertions(+), 25 deletions(-)
diff --git a/drivers/gpio/gpio-stmpe.c b/drivers/gpio/gpio-stmpe.c
index 5197edf..bfc918c 100644
--- a/drivers/gpio/gpio-stmpe.c
+++ b/drivers/gpio/gpio-stmpe.c
@@ -231,39 +231,74 @@ static void stmpe_dbg_show_one(struct seq_file *s,
gpio, label ?: "(none)",
val ? "hi" : "lo");
} else {
- u8 edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_MSB] + num_banks - 1 - (offset / 8);
- u8 rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB] - (offset / 8);
- u8 fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB] - (offset / 8);
- u8 irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB] - (offset / 8);
- bool edge_det;
- bool rise;
- bool fall;
+ u8 edge_det_reg;
+ u8 rise_reg;
+ u8 fall_reg;
+ u8 irqen_reg;
+
+ char *edge_det_values[] = {"edge-inactive",
+ "edge-asserted",
+ "not-supported"};
+ char *rise_values[] = {"no-rising-edge-detection",
+ "rising-edge-detection",
+ "not-supported"};
+ char *fall_values[] = {"no-falling-edge-detection",
+ "falling-edge-detection",
+ "not-supported"};
+ #define NOT_SUPPORTED_IDX 2
+ u8 edge_det = NOT_SUPPORTED_IDX;
+ u8 rise = NOT_SUPPORTED_IDX;
+ u8 fall = NOT_SUPPORTED_IDX;
bool irqen;
- ret = stmpe_reg_read(stmpe, edge_det_reg);
- if (ret < 0)
- return;
- edge_det = !!(ret & mask);
- ret = stmpe_reg_read(stmpe, rise_reg);
- if (ret < 0)
+ switch (stmpe->partnum) {
+ case STMPE610:
+ case STMPE811:
+ case STMPE1601:
+ case STMPE2401:
+ case STMPE2403:
+ edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_MSB] +
+ num_banks - 1 - (offset / 8);
+ ret = stmpe_reg_read(stmpe, edge_det_reg);
+ if (ret < 0)
+ return;
+ edge_det = !!(ret & mask);
+
+ case STMPE1801:
+ rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB] -
+ (offset / 8);
+ fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB] -
+ (offset / 8);
+ ret = stmpe_reg_read(stmpe, rise_reg);
+ if (ret < 0)
+ return;
+ rise = !!(ret & mask);
+ ret = stmpe_reg_read(stmpe, fall_reg);
+ if (ret < 0)
+ return;
+ fall = !!(ret & mask);
+
+ case STMPE801:
+ irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB] -
+ (offset / 8);
+ break;
+
+ default:
return;
- rise = !!(ret & mask);
- ret = stmpe_reg_read(stmpe, fall_reg);
- if (ret < 0)
- return;
- fall = !!(ret & mask);
+ }
+
ret = stmpe_reg_read(stmpe, irqen_reg);
if (ret < 0)
return;
irqen = !!(ret & mask);
- seq_printf(s, " gpio-%-3d (%-20.20s) in %s %s %s%s%s",
+ seq_printf(s, " gpio-%-3d (%-20.20s) in %s %13s %13s %25s %25s",
gpio, label ?: "(none)",
val ? "hi" : "lo",
- edge_det ? "edge-asserted" : "edge-inactive",
- irqen ? "IRQ-enabled" : "",
- rise ? " rising-edge-detection" : "",
- fall ? " falling-edge-detection" : "");
+ edge_det_values[edge_det],
+ irqen ? "IRQ-enabled" : "IRQ-disabled",
+ rise_values[rise],
+ fall_values[fall]);
}
}
@@ -322,8 +357,8 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
stmpe_reg_write(stmpe, statmsbreg + i, status[i]);
- /* Edge detect register is not present on 801 */
- if (stmpe->partnum != STMPE801)
+ /* Edge detect register is not present on 801 and 1801 */
+ if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1801)
stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_GPEDR_MSB]
+ i, status[i]);
}
--
1.9.1
From: Patrice Chotard <[email protected]>
In order to prepare the ground to STMPE1600,
as STMPE1600's SYS_CTRL register has the same layout as
STMPE801 variant, unify STMPExxx_REG_SYS_CTRL_RESET/INT_EN/INT_HI
bit masks to more generic STMPE_SYS_CTRL_RESET/INT_EN/INT_HI
Signed-off-by: Patrice Chotard <[email protected]>
---
drivers/mfd/stmpe.c | 4 ++--
drivers/mfd/stmpe.h | 6 ++----
2 files changed, 4 insertions(+), 6 deletions(-)
diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index af682d0..2556463 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -1089,7 +1089,7 @@ static int stmpe_chip_init(struct stmpe *stmpe)
if (stmpe->irq >= 0) {
if (id == STMPE801_ID)
- icr = STMPE801_REG_SYS_CTRL_INT_EN;
+ icr = STMPE_SYS_CTRL_INT_EN;
else
icr = STMPE_ICR_LSB_GIM;
@@ -1103,7 +1103,7 @@ static int stmpe_chip_init(struct stmpe *stmpe)
if (irq_trigger == IRQF_TRIGGER_RISING ||
irq_trigger == IRQF_TRIGGER_HIGH) {
if (id == STMPE801_ID)
- icr |= STMPE801_REG_SYS_CTRL_INT_HI;
+ icr |= STMPE_SYS_CTRL_INT_HI;
else
icr |= STMPE_ICR_LSB_HIGH;
}
diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h
index 4ae343d..4ba1123 100644
--- a/drivers/mfd/stmpe.h
+++ b/drivers/mfd/stmpe.h
@@ -105,6 +105,8 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE_ICR_LSB_GIM (1 << 0)
#define STMPE_SYS_CTRL_RESET (1 << 7)
+#define STMPE_SYS_CTRL_INT_EN (1 << 2)
+#define STMPE_SYS_CTRL_INT_HI (1 << 0)
/*
* STMPE801
@@ -121,10 +123,6 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE801_REG_GPIO_SET_PIN 0x11
#define STMPE801_REG_GPIO_DIR 0x12
-#define STMPE801_REG_SYS_CTRL_RESET (1 << 7)
-#define STMPE801_REG_SYS_CTRL_INT_EN (1 << 2)
-#define STMPE801_REG_SYS_CTRL_INT_HI (1 << 0)
-
/*
* STMPE811
*/
--
1.9.1
From: Patrice Chotard <[email protected]>
This update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset
This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.
For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: Patrice Chotard <[email protected]>
---
drivers/gpio/gpio-stmpe.c | 48 ++++++++++++++++++++++++++---------------------
1 file changed, 27 insertions(+), 21 deletions(-)
diff --git a/drivers/gpio/gpio-stmpe.c b/drivers/gpio/gpio-stmpe.c
index 2789bdc..6d6d76a 100644
--- a/drivers/gpio/gpio-stmpe.c
+++ b/drivers/gpio/gpio-stmpe.c
@@ -21,6 +21,8 @@
*/
enum { REG_RE, REG_FE, REG_IE };
+enum { LSB, CSB, MSB };
+
#define CACHE_NR_REGS 3
/* No variant has more than 24 GPIOs */
#define CACHE_NR_BANKS (24 / 8)
@@ -40,7 +42,7 @@ static int stmpe_gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(chip);
struct stmpe *stmpe = stmpe_gpio->stmpe;
- u8 reg = stmpe->regs[STMPE_IDX_GPMR_LSB] - (offset / 8);
+ u8 reg = stmpe->regs[STMPE_IDX_GPMR_LSB + (offset / 8)];
u8 mask = 1 << (offset % 8);
int ret;
@@ -56,7 +58,7 @@ static void stmpe_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(chip);
struct stmpe *stmpe = stmpe_gpio->stmpe;
int which = val ? STMPE_IDX_GPSR_LSB : STMPE_IDX_GPCR_LSB;
- u8 reg = stmpe->regs[which] - (offset / 8);
+ u8 reg = stmpe->regs[which + (offset / 8)];
u8 mask = 1 << (offset % 8);
/*
@@ -74,7 +76,7 @@ static int stmpe_gpio_direction_output(struct gpio_chip *chip,
{
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(chip);
struct stmpe *stmpe = stmpe_gpio->stmpe;
- u8 reg = stmpe->regs[STMPE_IDX_GPDR_LSB] - (offset / 8);
+ u8 reg = stmpe->regs[STMPE_IDX_GPDR_LSB + (offset / 8)];
u8 mask = 1 << (offset % 8);
stmpe_gpio_set(chip, offset, val);
@@ -87,7 +89,7 @@ static int stmpe_gpio_direction_input(struct gpio_chip *chip,
{
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(chip);
struct stmpe *stmpe = stmpe_gpio->stmpe;
- u8 reg = stmpe->regs[STMPE_IDX_GPDR_LSB] - (offset / 8);
+ u8 reg = stmpe->regs[STMPE_IDX_GPDR_LSB + (offset / 8)];
u8 mask = 1 << (offset % 8);
return stmpe_set_bits(stmpe, reg, mask, 0);
@@ -157,10 +159,16 @@ static void stmpe_gpio_irq_sync_unlock(struct irq_data *d)
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(gc);
struct stmpe *stmpe = stmpe_gpio->stmpe;
int num_banks = DIV_ROUND_UP(stmpe->num_gpios, 8);
- static const u8 regmap[] = {
- [REG_RE] = STMPE_IDX_GPRER_LSB,
- [REG_FE] = STMPE_IDX_GPFER_LSB,
- [REG_IE] = STMPE_IDX_IEGPIOR_LSB,
+ static const u8 regmap[CACHE_NR_REGS][CACHE_NR_BANKS] = {
+ [REG_RE][LSB] = STMPE_IDX_GPRER_LSB,
+ [REG_RE][CSB] = STMPE_IDX_GPRER_CSB,
+ [REG_RE][MSB] = STMPE_IDX_GPRER_MSB,
+ [REG_FE][LSB] = STMPE_IDX_GPFER_LSB,
+ [REG_FE][CSB] = STMPE_IDX_GPFER_CSB,
+ [REG_FE][MSB] = STMPE_IDX_GPFER_MSB,
+ [REG_IE][LSB] = STMPE_IDX_IEGPIOR_LSB,
+ [REG_IE][CSB] = STMPE_IDX_IEGPIOR_CSB,
+ [REG_IE][MSB] = STMPE_IDX_IEGPIOR_MSB,
};
int i, j;
@@ -178,7 +186,7 @@ static void stmpe_gpio_irq_sync_unlock(struct irq_data *d)
continue;
stmpe_gpio->oldregs[i][j] = new;
- stmpe_reg_write(stmpe, stmpe->regs[regmap[i]] - j, new);
+ stmpe_reg_write(stmpe, stmpe->regs[regmap[i][j]], new);
}
}
@@ -214,9 +222,9 @@ static void stmpe_dbg_show_one(struct seq_file *s,
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(gc);
struct stmpe *stmpe = stmpe_gpio->stmpe;
const char *label = gpiochip_is_requested(gc, offset);
- int num_banks = DIV_ROUND_UP(stmpe->num_gpios, 8);
bool val = !!stmpe_gpio_get(gc, offset);
- u8 dir_reg = stmpe->regs[STMPE_IDX_GPDR_LSB] - (offset / 8);
+ u8 bank = offset / 8;
+ u8 dir_reg = stmpe->regs[STMPE_IDX_GPDR_LSB + bank];
u8 mask = 1 << (offset % 8);
int ret;
u8 dir;
@@ -257,18 +265,16 @@ static void stmpe_dbg_show_one(struct seq_file *s,
case STMPE1601:
case STMPE2401:
case STMPE2403:
- edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_MSB] +
- num_banks - 1 - (offset / 8);
+ edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_LSB + bank];
ret = stmpe_reg_read(stmpe, edge_det_reg);
if (ret < 0)
return;
edge_det = !!(ret & mask);
case STMPE1801:
- rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB] -
- (offset / 8);
- fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB] -
- (offset / 8);
+ rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB + bank];
+ fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB + bank];
+
ret = stmpe_reg_read(stmpe, rise_reg);
if (ret < 0)
return;
@@ -279,8 +285,7 @@ static void stmpe_dbg_show_one(struct seq_file *s,
fall = !!(ret & mask);
case STMPE801:
- irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB] -
- (offset / 8);
+ irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB + bank];
break;
default:
@@ -362,8 +367,9 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
*/
if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1801) {
stmpe_reg_write(stmpe, statmsbreg + i, status[i]);
- stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_GPEDR_MSB]
- + i, status[i]);
+ stmpe_reg_write(stmpe,
+ stmpe->regs[STMPE_IDX_GPEDR_LSB + i],
+ status[i]);
}
}
--
1.9.1
From: Patrice Chotard <[email protected]>
This patch adds a new compatible string for stmpe mfd to support
stmpe1600 variant.
Signed-off-by: Amelie DELAUNAY <[email protected]>
Acked-by: Linus Walleij <[email protected]>
---
Documentation/devicetree/bindings/mfd/stmpe.txt | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt
index 3fb68bf..f9065a5 100644
--- a/Documentation/devicetree/bindings/mfd/stmpe.txt
+++ b/Documentation/devicetree/bindings/mfd/stmpe.txt
@@ -4,7 +4,7 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio,
keypad, touchscreen, adc, pwm, rotator.
Required properties:
- - compatible : "st,stmpe[610|801|811|1601|2401|2403]"
+ - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]"
- reg : I2C/SPI address of the device
Optional properties:
--
1.9.1
On Thu, Apr 28, 2016 at 2:13 PM, <[email protected]> wrote:
> From: Patrice Chotard <[email protected]>
>
> this update allows to use registers map as following :
> regs[reg_index + offset] instead of
> regs[reg_index] + offset
>
> This makes code clearer and will facilitate the addition of STMPE1600
> on which LSB and MSB registers are respectively located at addr and addr + 1.
> Despite for all others STMPE variant, LSB and MSB registers are respectively
> located in reverse order at addr + 1 and addr.
>
> For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
> which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
> register addresses (STMPE1801/STMPE24xx).
> For variant which have 2 registers's bank, we use LSB and CSB indexes only.
> In this case the CSB index contains the MSB regs address (STMPE 1601).
>
> Signed-off-by: Patrice Chotard <[email protected]>
Yep this is so much clearer!
Reviewed-by: Linus Walleij <[email protected]>
Yours,
Linus Walleij
On Thu, Apr 28, 2016 at 2:13 PM, <[email protected]> wrote:
> From: Patrice Chotard <[email protected]>
>
> This update allows to use registers map as following :
> regs[reg_index + offset] instead of
> regs[reg_index] + offset
>
> This makes code clearer and will facilitate the addition of STMPE1600
> on which LSB and MSB registers are respectively located at addr and addr + 1.
> Despite for all others STMPE variant, LSB and MSB registers are respectively
> located in reverse order at addr + 1 and addr.
>
> For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
> which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
> register addresses (STMPE1801/STMPE24xx).
> For variant which have 2 registers's bank, we use LSB and CSB indexes only.
> In this case the CSB index contains the MSB regs address (STMPE 1601).
>
> Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Yours,
Linus Walleij
On Thu, Apr 28, 2016 at 2:13 PM, <[email protected]> wrote:
> From: Patrice Chotard <[email protected]>
>
> The particularities of this variant are:
> - GPIO_XXX_LSB and GPIO_XXX_MSB memory locations are inverted compared
> to other variants.
> - There is no Edge detection, Rising Edge and Falling Edge registers.
> - IRQ flags are cleared when read, no need to write in Status register.
>
> Signed-off-by: Amelie DELAUNAY <[email protected]>
> Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Yours,
Linus Walleij
On Thu, Apr 28, 2016 at 2:12 PM, <[email protected]> wrote:
> From: Patrice Chotard <[email protected]>
>
> This series cleans and fixes some bugs in MFD/GPIO STMPE drivers and prepare
> the ground to add new STMPE1600 support.
This series is finished and looking good from a GPIO perspective.
Lee, once you feel satisfied with the patches and merge them
I'd need an immutable branch, this one I definately have to pull
into the GPIO tree (because of dependent patches).
Yours,
Linus Walleij
On Thu, 2016-04-28 at 14:12 +0200, [email protected] wrote:
> From: Patrice Chotard <[email protected]>
>
>
> This series cleans and fixes some bugs in MFD/GPIO STMPE drivers and
> prepare
> the ground to add new STMPE1600 support.
>
> STMPE1600 datasheet is available here :
> http://www2.st.com/content/st_com/en/products/interfaces-and-transcei
> vers/
> i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html
>
> Only STMPE1600 has been tested on STM32 platform. As i have no board
> with
> others STMPE
> variant(STMPE610/STMPE801/STMPE811/STMPE1601/STMPE1801/STMPE2401
> and STMPE2403), i put in CC boards's maintainers which are using
> others STMPE variant.
>
> If they can kindly check that no regression has been introduce by
> this series
> :
>
> For ARM/FREESCALE IMX / MXC ARM ARCHITECTURE:
> _ Shawn Guo <[email protected]>
> _ Sascha Hauer <[email protected]>
>
> For ARM/SOCFPGA ARCHITECTURE
> _ Dinh Nguyen <[email protected]>
>
> For SPEAR PLATFORM SUPPORT
> _ Viresh Kumar <[email protected]>
> _ Shiraz Hashim <[email protected]>
>
> For Apalis/Colibri board SUPPORT
> _ [email protected]
> _ [email protected]
> _ [email protected]
> _ Thierry Reding <[email protected]>
> _ Alexandre Courbot <[email protected]>
>
> For ARM/Ux500 ARM ARCHITECTURE
> _ Linus Walleij <[email protected]>
>
>
> v1 => v2:
> _ update Cc list
> _ fix kbuild test robot warnings on original patch 3
> _ split patch 6 to extract usage of generic bitmask name
> _ split patch 6 and 7 and introduce a new way to access
> registers
> for both mfd/stmpe and gpio/gpio-stmpe drivers.
> _ remove patch 8
>
> Patrice Chotard (10):
> mfd: stmpe: Add STMPE_IDX_SYS_CTRL/2 enum
> mfd: stmpe: Add reset support for all STMPE variant
> gpio: stmpe: fix edge and rising/falling edge detection
> gpio: stmpe: write int status register only when needed
> mfd: stmpe: use generic bit mask name
> mfd: stmpe: rework registers access
> gpio: stmpe: rework registers access
> Documentation: dt: add stmpe1600 compatible string to stmpe mfd
> mfd: Add STMPE1600 support
> gpio: stmpe: Add STMPE1600 support
>
> Documentation/devicetree/bindings/mfd/stmpe.txt | 2 +-
> drivers/gpio/gpio-stmpe.c | 167
> +++++++++++++++++-------
> drivers/mfd/stmpe-i2c.c | 2 +
> drivers/mfd/stmpe.c | 161
> +++++++++++++++++++----
> drivers/mfd/stmpe.h | 85 ++++++++++--
> include/linux/mfd/stmpe.h | 21 +++
> 6 files changed, 352 insertions(+), 86 deletions(-)
I gave the whole series a spin both on Apalis iMX6Q 2GB IT V1.1B as
well as Apalis T30 2GB V1.1A both featuring a STMPE811 and an EDT VGA
touch panel connected to it still works perfectly running LXDE on top
of the modesetting X driver.
Tested-by: Marcel Ziswiler <[email protected]>