thermal_zone_device_check --> thermal_zone_device_update -->
handle_thermal_trip --> handle_critical_trips --> orderly_poweroff
The above sequence happens every 250/500 mS based on the configuration.
The orderly_poweroff function is getting called every 250/500 mS.
With a full fledged file system it takes at least 5-10 Seconds to
power off gracefully.
In that period due to the thermal_zone_device_check triggering
periodically the thermal work queues bombard with
orderly_poweroff calls multiple times eventually leading to
failures in gracefully powering off the system.
Make sure that orderly_poweroff is called only once.
Reported-by: Nishanth Menon <[email protected]>
Signed-off-by: Keerthy <[email protected]>
---
Changes in v2:
* Added a global mutex to serialize poweroff code sequence.
drivers/thermal/thermal_core.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c
index 11f0675..7462ae5 100644
--- a/drivers/thermal/thermal_core.c
+++ b/drivers/thermal/thermal_core.c
@@ -45,6 +45,7 @@
static DEFINE_MUTEX(thermal_list_lock);
static DEFINE_MUTEX(thermal_governor_lock);
+static DEFINE_MUTEX(poweroff_lock);
static atomic_t in_suspend;
@@ -326,6 +327,7 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
int trip, enum thermal_trip_type trip_type)
{
int trip_temp;
+ static bool power_off_triggered;
tz->ops->get_trip_temp(tz, trip, &trip_temp);
@@ -338,11 +340,14 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
if (tz->ops->notify)
tz->ops->notify(tz, trip, trip_type);
- if (trip_type == THERMAL_TRIP_CRITICAL) {
+ if (trip_type == THERMAL_TRIP_CRITICAL && !power_off_triggered) {
dev_emerg(&tz->device,
"critical temperature reached(%d C),shutting down\n",
tz->temperature / 1000);
+ mutex_lock(&poweroff_lock);
orderly_poweroff(true);
+ power_off_triggered = true;
+ mutex_unlock(&poweroff_lock);
}
}
@@ -1463,6 +1468,7 @@ static int __init thermal_init(void)
{
int result;
+ mutex_init(&poweroff_lock);
result = thermal_register_governors();
if (result)
goto error;
@@ -1497,6 +1503,7 @@ static int __init thermal_init(void)
ida_destroy(&thermal_cdev_ida);
mutex_destroy(&thermal_list_lock);
mutex_destroy(&thermal_governor_lock);
+ mutex_destroy(&poweroff_lock);
return result;
}
--
1.9.1
orderly_poweroff is triggered when a graceful shutdown
of system is desired. This may be used in many critical states of the
kernel such as when subsystems detects conditions such as critical
temperature conditions. However, in certain conditions in system
boot up sequences like those in the middle of driver probes being
initiated, userspace will be unable to power off the system in a clean
manner and leaves the system in a critical state. In cases like these,
the /sbin/poweroff will return success (having forked off to attempt
powering off the system. However, the system overall will fail to
completely poweroff (since other modules will be probed) and the system
is still functional with no userspace (since that would have shut itself
off).
However, there is no clean way of detecting such failure of userspace
powering off the system. In such scenarios, it is necessary for a backup
workqueue to be able to force a shutdown of the system when orderly
shutdown is not successful after a configurable time period.
Reported-by: Nishanth Menon <[email protected]>
Signed-off-by: Keerthy <[email protected]>
---
* Changed the comment style
* Added backup shutdown call before orderly_poweroff
drivers/thermal/Kconfig | 13 ++++++++++++
drivers/thermal/thermal_core.c | 47 ++++++++++++++++++++++++++++++++++++++++++
2 files changed, 60 insertions(+)
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 9347401..971fd54 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -15,6 +15,19 @@ menuconfig THERMAL
if THERMAL
+config THERMAL_EMERGENCY_POWEROFF_DELAY_MS
+ int "Emergency poweroff delay in milli-seconds"
+ depends on THERMAL
+ default 0
+ help
+ The number of milliseconds to delay before emergency
+ poweroff kicks in. The delay should be carefully profiled
+ so as to give adequate time for orderly_poweroff. In case
+ of failure of an orderly_poweroff the emergency poweroff
+ kicks in after the delay has elapsed and shuts down the system.
+
+ If set to 0 poweroff will happen immediately.
+
config THERMAL_HWMON
bool
prompt "Expose thermal sensors as hwmon device"
diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c
index 7462ae5..d60fa9e 100644
--- a/drivers/thermal/thermal_core.c
+++ b/drivers/thermal/thermal_core.c
@@ -323,12 +323,54 @@ static void handle_non_critical_trips(struct thermal_zone_device *tz,
def_governor->throttle(tz, trip);
}
+/**
+ * emergency_poweroff_func - emergency poweroff work after a known delay
+ * @work: work_struct associated with the emergency poweroff function
+ *
+ * This function is called in very critical situations to force
+ * a kernel poweroff after a configurable timeout value.
+ */
+static void emergency_poweroff_func(struct work_struct *work)
+{
+ /*
+ * We have reached here after the emergency thermal shutdown
+ * Waiting period has expired. This means orderly_poweroff has
+ * not been able to shut off the system for some reason.
+ * Try to shut down the system immediately using kernel_power_off
+ * if populated
+ */
+ pr_warn("Attempting kernel_power_off\n");
+ kernel_power_off();
+
+ /*
+ * Worst of the worst case trigger emergency restart
+ */
+ pr_warn("kernel_power_off has failed! Attempting emergency_restart\n");
+ emergency_restart();
+}
+
+static DECLARE_DELAYED_WORK(emergency_poweroff_work, emergency_poweroff_func);
+
+/**
+ * emergency_poweroff - Trigger an emergency system poweroff
+ *
+ * This may be called from any critical situation to trigger a system shutdown
+ * after a known period of time. By default the delay is 0 millisecond
+ */
+void thermal_emergency_poweroff(void)
+{
+ schedule_delayed_work(&emergency_poweroff_work,
+ msecs_to_jiffies(CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS));
+}
+
static void handle_critical_trips(struct thermal_zone_device *tz,
int trip, enum thermal_trip_type trip_type)
{
int trip_temp;
static bool power_off_triggered;
+ static struct mutex poweroff_lock;
+ mutex_init(&poweroff_lock);
tz->ops->get_trip_temp(tz, trip, &trip_temp);
/* If we have not crossed the trip_temp, we do not care. */
@@ -345,6 +387,11 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
"critical temperature reached(%d C),shutting down\n",
tz->temperature / 1000);
mutex_lock(&poweroff_lock);
+ /*
+ * Queue a backup emergency shutdown in the event of
+ * orderly_poweroff failure.
+ */
+ thermal_emergency_poweroff();
orderly_poweroff(true);
power_off_triggered = true;
mutex_unlock(&poweroff_lock);
--
1.9.1
Hey,
On Thu, Apr 13, 2017 at 01:32:35PM +0530, Keerthy wrote:
> thermal_zone_device_check --> thermal_zone_device_update -->
> handle_thermal_trip --> handle_critical_trips --> orderly_poweroff
>
> The above sequence happens every 250/500 mS based on the configuration.
> The orderly_poweroff function is getting called every 250/500 mS.
> With a full fledged file system it takes at least 5-10 Seconds to
> power off gracefully.
>
> In that period due to the thermal_zone_device_check triggering
> periodically the thermal work queues bombard with
> orderly_poweroff calls multiple times eventually leading to
> failures in gracefully powering off the system.
>
> Make sure that orderly_poweroff is called only once.
>
> Reported-by: Nishanth Menon <[email protected]>
Was this reported by nm or found by you?
> Signed-off-by: Keerthy <[email protected]>
> ---
>
> Changes in v2:
>
> * Added a global mutex to serialize poweroff code sequence.
>
> drivers/thermal/thermal_core.c | 9 ++++++++-
> 1 file changed, 8 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c
> index 11f0675..7462ae5 100644
> --- a/drivers/thermal/thermal_core.c
> +++ b/drivers/thermal/thermal_core.c
> @@ -45,6 +45,7 @@
>
> static DEFINE_MUTEX(thermal_list_lock);
> static DEFINE_MUTEX(thermal_governor_lock);
> +static DEFINE_MUTEX(poweroff_lock);
>
> static atomic_t in_suspend;
>
> @@ -326,6 +327,7 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
> int trip, enum thermal_trip_type trip_type)
> {
> int trip_temp;
> + static bool power_off_triggered;
>
> tz->ops->get_trip_temp(tz, trip, &trip_temp);
>
> @@ -338,11 +340,14 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
> if (tz->ops->notify)
> tz->ops->notify(tz, trip, trip_type);
>
> - if (trip_type == THERMAL_TRIP_CRITICAL) {
> + if (trip_type == THERMAL_TRIP_CRITICAL && !power_off_triggered) {
> dev_emerg(&tz->device,
> "critical temperature reached(%d C),shutting down\n",
> tz->temperature / 1000);
> + mutex_lock(&poweroff_lock);
> orderly_poweroff(true);
> + power_off_triggered = true;
> + mutex_unlock(&poweroff_lock);
The above code does not fully prevent orderly_poweroff() to be called
only once, does it?
- thermal zone 0 goes all the way in the critical path, but gets
preempted between orderly_poweroff(true)l and power_off_triggered =
true;, i.e., preempted right before setting to true, therefore,
power_off_triggered still 0.
- thermal zone 1 also enters critical path, but will sleep at the
power_off_lock, right?
- then thermal zone 0 gets the CPU again, finishes the critical path,
unlocks poweroff_lock.
- thermal zone 1 is unblocked, and call again orderly_poweroff(true);
BR,
> }
> }
>
> @@ -1463,6 +1468,7 @@ static int __init thermal_init(void)
> {
> int result;
>
> + mutex_init(&poweroff_lock);
> result = thermal_register_governors();
> if (result)
> goto error;
> @@ -1497,6 +1503,7 @@ static int __init thermal_init(void)
> ida_destroy(&thermal_cdev_ida);
> mutex_destroy(&thermal_list_lock);
> mutex_destroy(&thermal_governor_lock);
> + mutex_destroy(&poweroff_lock);
> return result;
> }
>
> --
> 1.9.1
>
Hey,
On Thu, Apr 13, 2017 at 01:32:36PM +0530, Keerthy wrote:
> orderly_poweroff is triggered when a graceful shutdown
> of system is desired. This may be used in many critical states of the
> kernel such as when subsystems detects conditions such as critical
> temperature conditions. However, in certain conditions in system
> boot up sequences like those in the middle of driver probes being
> initiated, userspace will be unable to power off the system in a clean
> manner and leaves the system in a critical state. In cases like these,
> the /sbin/poweroff will return success (having forked off to attempt
> powering off the system. However, the system overall will fail to
> completely poweroff (since other modules will be probed) and the system
> is still functional with no userspace (since that would have shut itself
> off).
>
> However, there is no clean way of detecting such failure of userspace
> powering off the system. In such scenarios, it is necessary for a backup
> workqueue to be able to force a shutdown of the system when orderly
> shutdown is not successful after a configurable time period.
Thanks for keeping this thread up and fixing it. Some requests to this
patch too as follows.
>
> Reported-by: Nishanth Menon <[email protected]>
> Signed-off-by: Keerthy <[email protected]>
> ---
>
> * Changed the comment style
> * Added backup shutdown call before orderly_poweroff
>
> drivers/thermal/Kconfig | 13 ++++++++++++
> drivers/thermal/thermal_core.c | 47 ++++++++++++++++++++++++++++++++++++++++++
I think this change in expectation should probably be documented under
Documentation/ directory. Can you please patch thermal documentation
too?
> 2 files changed, 60 insertions(+)
>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 9347401..971fd54 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -15,6 +15,19 @@ menuconfig THERMAL
>
> if THERMAL
>
> +config THERMAL_EMERGENCY_POWEROFF_DELAY_MS
> + int "Emergency poweroff delay in milli-seconds"
> + depends on THERMAL
> + default 0
> + help
> + The number of milliseconds to delay before emergency
> + poweroff kicks in. The delay should be carefully profiled
> + so as to give adequate time for orderly_poweroff. In case
> + of failure of an orderly_poweroff the emergency poweroff
> + kicks in after the delay has elapsed and shuts down the system.
> +
> + If set to 0 poweroff will happen immediately.
> +
> config THERMAL_HWMON
> bool
> prompt "Expose thermal sensors as hwmon device"
> diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c
> index 7462ae5..d60fa9e 100644
> --- a/drivers/thermal/thermal_core.c
> +++ b/drivers/thermal/thermal_core.c
> @@ -323,12 +323,54 @@ static void handle_non_critical_trips(struct thermal_zone_device *tz,
> def_governor->throttle(tz, trip);
> }
>
> +/**
> + * emergency_poweroff_func - emergency poweroff work after a known delay
> + * @work: work_struct associated with the emergency poweroff function
> + *
> + * This function is called in very critical situations to force
> + * a kernel poweroff after a configurable timeout value.
> + */
> +static void emergency_poweroff_func(struct work_struct *work)
> +{
> + /*
> + * We have reached here after the emergency thermal shutdown
> + * Waiting period has expired. This means orderly_poweroff has
> + * not been able to shut off the system for some reason.
> + * Try to shut down the system immediately using kernel_power_off
> + * if populated
> + */
> + pr_warn("Attempting kernel_power_off\n");
This message needs to be specific to thermal (forced) shutdown.
> + kernel_power_off();
> +
> + /*
> + * Worst of the worst case trigger emergency restart
> + */
> + pr_warn("kernel_power_off has failed! Attempting emergency_restart\n");
Same here..
also, I think if your system reached this point, we should probably be more
dramatic at the kernel log a scream louder, I would say a big farty WARN
to say the least. Or a crash.
> + emergency_restart();
> +}
> +
> +static DECLARE_DELAYED_WORK(emergency_poweroff_work, emergency_poweroff_func);
> +
> +/**
> + * emergency_poweroff - Trigger an emergency system poweroff
> + *
> + * This may be called from any critical situation to trigger a system shutdown
> + * after a known period of time. By default the delay is 0 millisecond
> + */
> +void thermal_emergency_poweroff(void)
> +{
> + schedule_delayed_work(&emergency_poweroff_work,
> + msecs_to_jiffies(CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS));
> +}
> +
> static void handle_critical_trips(struct thermal_zone_device *tz,
> int trip, enum thermal_trip_type trip_type)
> {
> int trip_temp;
> static bool power_off_triggered;
> + static struct mutex poweroff_lock;
>
> + mutex_init(&poweroff_lock);
> tz->ops->get_trip_temp(tz, trip, &trip_temp);
>
the above is probably a quirk?
> /* If we have not crossed the trip_temp, we do not care. */
> @@ -345,6 +387,11 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
> "critical temperature reached(%d C),shutting down\n",
> tz->temperature / 1000);
> mutex_lock(&poweroff_lock);
> + /*
> + * Queue a backup emergency shutdown in the event of
> + * orderly_poweroff failure.
> + */
> + thermal_emergency_poweroff();
> orderly_poweroff(true);
> power_off_triggered = true;
> mutex_unlock(&poweroff_lock);
> --
> 1.9.1
>
On Thursday 13 April 2017 08:46 PM, Eduardo Valentin wrote:
> Hey,
>
> On Thu, Apr 13, 2017 at 01:32:35PM +0530, Keerthy wrote:
>> thermal_zone_device_check --> thermal_zone_device_update -->
>> handle_thermal_trip --> handle_critical_trips --> orderly_poweroff
>>
>> The above sequence happens every 250/500 mS based on the configuration.
>> The orderly_poweroff function is getting called every 250/500 mS.
>> With a full fledged file system it takes at least 5-10 Seconds to
>> power off gracefully.
>>
>> In that period due to the thermal_zone_device_check triggering
>> periodically the thermal work queues bombard with
>> orderly_poweroff calls multiple times eventually leading to
>> failures in gracefully powering off the system.
>>
>> Make sure that orderly_poweroff is called only once.
>>
>> Reported-by: Nishanth Menon <[email protected]>
>
> Was this reported by nm or found by you?
Okay i found it when i was debugging the problem reported by nm :-).
I will fix that.
>
>> Signed-off-by: Keerthy <[email protected]>
>> ---
>>
>> Changes in v2:
>>
>> * Added a global mutex to serialize poweroff code sequence.
>>
>> drivers/thermal/thermal_core.c | 9 ++++++++-
>> 1 file changed, 8 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c
>> index 11f0675..7462ae5 100644
>> --- a/drivers/thermal/thermal_core.c
>> +++ b/drivers/thermal/thermal_core.c
>> @@ -45,6 +45,7 @@
>>
>> static DEFINE_MUTEX(thermal_list_lock);
>> static DEFINE_MUTEX(thermal_governor_lock);
>> +static DEFINE_MUTEX(poweroff_lock);
>>
>> static atomic_t in_suspend;
>>
>> @@ -326,6 +327,7 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
>> int trip, enum thermal_trip_type trip_type)
>> {
>> int trip_temp;
>> + static bool power_off_triggered;
>>
>> tz->ops->get_trip_temp(tz, trip, &trip_temp);
>>
>> @@ -338,11 +340,14 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
>> if (tz->ops->notify)
>> tz->ops->notify(tz, trip, trip_type);
>>
>> - if (trip_type == THERMAL_TRIP_CRITICAL) {
>> + if (trip_type == THERMAL_TRIP_CRITICAL && !power_off_triggered) {
>> dev_emerg(&tz->device,
>> "critical temperature reached(%d C),shutting down\n",
>> tz->temperature / 1000);
>> + mutex_lock(&poweroff_lock);
>> orderly_poweroff(true);
>> + power_off_triggered = true;
>> + mutex_unlock(&poweroff_lock);
>
> The above code does not fully prevent orderly_poweroff() to be called
> only once, does it?
>
> - thermal zone 0 goes all the way in the critical path, but gets
> preempted between orderly_poweroff(true)l and power_off_triggered =
> true;, i.e., preempted right before setting to true, therefore,
> power_off_triggered still 0.
> - thermal zone 1 also enters critical path, but will sleep at the
> power_off_lock, right?
> - then thermal zone 0 gets the CPU again, finishes the critical path,
> unlocks poweroff_lock.
> - thermal zone 1 is unblocked, and call again orderly_poweroff(true);
Oh yes! I will fix that
if (trip_type == THERMAL_TRIP_CRITICAL) {
dev_emerg(&tz->device,
"critical temperature reached(%d C),shutting
down\n",tz->temperature / 1000);
mutex_lock(&poweroff_lock);
if (!power_off_triggered) {
orderly_poweroff(true);
power_off_triggered = true;
}
mutex_unlock(&poweroff_lock);
}
The above should take care.
>
>
>
> BR,
>> }
>> }
>>
>> @@ -1463,6 +1468,7 @@ static int __init thermal_init(void)
>> {
>> int result;
>>
>> + mutex_init(&poweroff_lock);
>> result = thermal_register_governors();
>> if (result)
>> goto error;
>> @@ -1497,6 +1503,7 @@ static int __init thermal_init(void)
>> ida_destroy(&thermal_cdev_ida);
>> mutex_destroy(&thermal_list_lock);
>> mutex_destroy(&thermal_governor_lock);
>> + mutex_destroy(&poweroff_lock);
>> return result;
>> }
>>
>> --
>> 1.9.1
>>
On Thursday 13 April 2017 08:55 PM, Eduardo Valentin wrote:
>
> Hey,
>
> On Thu, Apr 13, 2017 at 01:32:36PM +0530, Keerthy wrote:
>> orderly_poweroff is triggered when a graceful shutdown
>> of system is desired. This may be used in many critical states of the
>> kernel such as when subsystems detects conditions such as critical
>> temperature conditions. However, in certain conditions in system
>> boot up sequences like those in the middle of driver probes being
>> initiated, userspace will be unable to power off the system in a clean
>> manner and leaves the system in a critical state. In cases like these,
>> the /sbin/poweroff will return success (having forked off to attempt
>> powering off the system. However, the system overall will fail to
>> completely poweroff (since other modules will be probed) and the system
>> is still functional with no userspace (since that would have shut itself
>> off).
>>
>> However, there is no clean way of detecting such failure of userspace
>> powering off the system. In such scenarios, it is necessary for a backup
>> workqueue to be able to force a shutdown of the system when orderly
>> shutdown is not successful after a configurable time period.
>
> Thanks for keeping this thread up and fixing it. Some requests to this
> patch too as follows.
>
>>
>> Reported-by: Nishanth Menon <[email protected]>
>> Signed-off-by: Keerthy <[email protected]>
>> ---
>>
>> * Changed the comment style
>> * Added backup shutdown call before orderly_poweroff
>>
>> drivers/thermal/Kconfig | 13 ++++++++++++
>> drivers/thermal/thermal_core.c | 47 ++++++++++++++++++++++++++++++++++++++++++
>
> I think this change in expectation should probably be documented under
> Documentation/ directory. Can you please patch thermal documentation
> too?
Okay.
>
>> 2 files changed, 60 insertions(+)
>>
>> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
>> index 9347401..971fd54 100644
>> --- a/drivers/thermal/Kconfig
>> +++ b/drivers/thermal/Kconfig
>> @@ -15,6 +15,19 @@ menuconfig THERMAL
>>
>> if THERMAL
>>
>> +config THERMAL_EMERGENCY_POWEROFF_DELAY_MS
>> + int "Emergency poweroff delay in milli-seconds"
>> + depends on THERMAL
>> + default 0
>> + help
>> + The number of milliseconds to delay before emergency
>> + poweroff kicks in. The delay should be carefully profiled
>> + so as to give adequate time for orderly_poweroff. In case
>> + of failure of an orderly_poweroff the emergency poweroff
>> + kicks in after the delay has elapsed and shuts down the system.
>> +
>> + If set to 0 poweroff will happen immediately.
>> +
>> config THERMAL_HWMON
>> bool
>> prompt "Expose thermal sensors as hwmon device"
>> diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c
>> index 7462ae5..d60fa9e 100644
>> --- a/drivers/thermal/thermal_core.c
>> +++ b/drivers/thermal/thermal_core.c
>> @@ -323,12 +323,54 @@ static void handle_non_critical_trips(struct thermal_zone_device *tz,
>> def_governor->throttle(tz, trip);
>> }
>>
>> +/**
>> + * emergency_poweroff_func - emergency poweroff work after a known delay
>> + * @work: work_struct associated with the emergency poweroff function
>> + *
>> + * This function is called in very critical situations to force
>> + * a kernel poweroff after a configurable timeout value.
>> + */
>> +static void emergency_poweroff_func(struct work_struct *work)
>> +{
>> + /*
>> + * We have reached here after the emergency thermal shutdown
>> + * Waiting period has expired. This means orderly_poweroff has
>> + * not been able to shut off the system for some reason.
>> + * Try to shut down the system immediately using kernel_power_off
>> + * if populated
>> + */
>> + pr_warn("Attempting kernel_power_off\n");
>
> This message needs to be specific to thermal (forced) shutdown.
Sure.
>
>> + kernel_power_off();
>> +
>> + /*
>> + * Worst of the worst case trigger emergency restart
>> + */
>> + pr_warn("kernel_power_off has failed! Attempting emergency_restart\n");
>
> Same here..
okay.
>
> also, I think if your system reached this point, we should probably be more
> dramatic at the kernel log a scream louder, I would say a big farty WARN
> to say the least. Or a crash.
warning should do.
>
>> + emergency_restart();
>> +}
>> +
>> +static DECLARE_DELAYED_WORK(emergency_poweroff_work, emergency_poweroff_func);
>> +
>> +/**
>> + * emergency_poweroff - Trigger an emergency system poweroff
>> + *
>> + * This may be called from any critical situation to trigger a system shutdown
>> + * after a known period of time. By default the delay is 0 millisecond
>> + */
>> +void thermal_emergency_poweroff(void)
>> +{
>> + schedule_delayed_work(&emergency_poweroff_work,
>> + msecs_to_jiffies(CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS));
>> +}
>> +
>> static void handle_critical_trips(struct thermal_zone_device *tz,
>> int trip, enum thermal_trip_type trip_type)
>> {
>> int trip_temp;
>> static bool power_off_triggered;
>> + static struct mutex poweroff_lock;
>>
>> + mutex_init(&poweroff_lock);
>> tz->ops->get_trip_temp(tz, trip, &trip_temp);
>>
>
> the above is probably a quirk?
Ya unnecessary. Thanks for catching this.
>
>> /* If we have not crossed the trip_temp, we do not care. */
>> @@ -345,6 +387,11 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
>> "critical temperature reached(%d C),shutting down\n",
>> tz->temperature / 1000);
>> mutex_lock(&poweroff_lock);
>> + /*
>> + * Queue a backup emergency shutdown in the event of
>> + * orderly_poweroff failure.
>> + */
>> + thermal_emergency_poweroff();
>> orderly_poweroff(true);
>> power_off_triggered = true;
>> mutex_unlock(&poweroff_lock);
>> --
>> 1.9.1
>>