Change since v4:
- fine tune the mipi_tx->ref_clk and mipi_tx->pll sequence
1. Prepare mipi_tx->ref_clk
2. Prepare mipi_tx->pll
3. Enable mipi_tx->ref_clk
4. Enable mipi_tx->pll
Changes since v3:
- turn off PLL before setting PLL parameters.
Changes since v2:
- update Acked-by: Rob Herring <[email protected]>
- update mt8183 max bit rate support
Changes since v1:
- update dt-bindings document for mt8183 mipitx.
- remove mtk_mipitx_clk_get_ops and assign clk_ops in probe.
- fix the lincence
- remove txdiv1 from mtk_mipi_tx_pll_prepare
Jitao Shi (3):
dt-bindings: display: mediatek: update dsi supported chips
drm/mediatek: separate mipi_tx to different file
drm/mediatek: add mipi_tx driver for mt8183
.../display/mediatek/mediatek,dsi.txt | 4 +-
drivers/gpu/drm/mediatek/Makefile | 2 +
drivers/gpu/drm/mediatek/mtk_mipi_tx.c | 345 ++----------------
drivers/gpu/drm/mediatek/mtk_mipi_tx.h | 50 +++
drivers/gpu/drm/mediatek/mtk_mt8173_mipi_tx.c | 289 +++++++++++++++
drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c | 181 +++++++++
6 files changed, 550 insertions(+), 321 deletions(-)
create mode 100644 drivers/gpu/drm/mediatek/mtk_mipi_tx.h
create mode 100644 drivers/gpu/drm/mediatek/mtk_mt8173_mipi_tx.c
create mode 100644 drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
--
2.21.0
Update device tree binding documentation for the dsi for
Mediatek MT8183 SoCs.
Signed-off-by: Jitao Shi <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
.../devicetree/bindings/display/mediatek/mediatek,dsi.txt | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
index fadf327c7cdf..a19a6cc375ed 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
@@ -7,7 +7,7 @@ channel output.
Required properties:
- compatible: "mediatek,<chip>-dsi"
- the supported chips are mt2701 and mt8173.
+ the supported chips are mt2701, mt8173 and mt8183.
- reg: Physical base address and length of the controller's registers
- interrupts: The interrupt signal from the function block.
- clocks: device clocks
@@ -26,7 +26,7 @@ The MIPI TX configuration module controls the MIPI D-PHY.
Required properties:
- compatible: "mediatek,<chip>-mipi-tx"
- the supported chips are mt2701 and mt8173.
+ the supported chips are mt2701, mt8173 and mt8183.
- reg: Physical base address and length of the controller's registers
- clocks: PLL reference clock
- clock-output-names: name of the output clock line to the DSI encoder
--
2.21.0
Different IC has different mipi_tx setting of dsi.
This patch separates the mipi_tx hardware relate part for mt8173.
Signed-off-by: Jitao Shi <[email protected]>
Reviewed-by: CK Hu <[email protected]>
---
drivers/gpu/drm/mediatek/Makefile | 1 +
drivers/gpu/drm/mediatek/mtk_mipi_tx.c | 343 ++----------------
drivers/gpu/drm/mediatek/mtk_mipi_tx.h | 49 +++
drivers/gpu/drm/mediatek/mtk_mt8173_mipi_tx.c | 289 +++++++++++++++
4 files changed, 363 insertions(+), 319 deletions(-)
create mode 100644 drivers/gpu/drm/mediatek/mtk_mipi_tx.h
create mode 100644 drivers/gpu/drm/mediatek/mtk_mt8173_mipi_tx.c
diff --git a/drivers/gpu/drm/mediatek/Makefile b/drivers/gpu/drm/mediatek/Makefile
index 82ae49c64221..2c8de1f5a5ee 100644
--- a/drivers/gpu/drm/mediatek/Makefile
+++ b/drivers/gpu/drm/mediatek/Makefile
@@ -12,6 +12,7 @@ mediatek-drm-y := mtk_disp_color.o \
mtk_drm_plane.o \
mtk_dsi.o \
mtk_mipi_tx.o \
+ mtk_mt8173_mipi_tx.o \
mtk_dpi.o
obj-$(CONFIG_DRM_MEDIATEK) += mediatek-drm.o
diff --git a/drivers/gpu/drm/mediatek/mtk_mipi_tx.c b/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
index 90e913108950..cdc68b88cefd 100644
--- a/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
+++ b/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
@@ -11,292 +11,39 @@
* GNU General Public License for more details.
*/
-#include <linux/clk.h>
-#include <linux/clk-provider.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/module.h>
-#include <linux/of_device.h>
-#include <linux/platform_device.h>
-#include <linux/phy/phy.h>
-
-#define MIPITX_DSI_CON 0x00
-#define RG_DSI_LDOCORE_EN BIT(0)
-#define RG_DSI_CKG_LDOOUT_EN BIT(1)
-#define RG_DSI_BCLK_SEL (3 << 2)
-#define RG_DSI_LD_IDX_SEL (7 << 4)
-#define RG_DSI_PHYCLK_SEL (2 << 8)
-#define RG_DSI_DSICLK_FREQ_SEL BIT(10)
-#define RG_DSI_LPTX_CLMP_EN BIT(11)
-
-#define MIPITX_DSI_CLOCK_LANE 0x04
-#define MIPITX_DSI_DATA_LANE0 0x08
-#define MIPITX_DSI_DATA_LANE1 0x0c
-#define MIPITX_DSI_DATA_LANE2 0x10
-#define MIPITX_DSI_DATA_LANE3 0x14
-#define RG_DSI_LNTx_LDOOUT_EN BIT(0)
-#define RG_DSI_LNTx_CKLANE_EN BIT(1)
-#define RG_DSI_LNTx_LPTX_IPLUS1 BIT(2)
-#define RG_DSI_LNTx_LPTX_IPLUS2 BIT(3)
-#define RG_DSI_LNTx_LPTX_IMINUS BIT(4)
-#define RG_DSI_LNTx_LPCD_IPLUS BIT(5)
-#define RG_DSI_LNTx_LPCD_IMINUS BIT(6)
-#define RG_DSI_LNTx_RT_CODE (0xf << 8)
-
-#define MIPITX_DSI_TOP_CON 0x40
-#define RG_DSI_LNT_INTR_EN BIT(0)
-#define RG_DSI_LNT_HS_BIAS_EN BIT(1)
-#define RG_DSI_LNT_IMP_CAL_EN BIT(2)
-#define RG_DSI_LNT_TESTMODE_EN BIT(3)
-#define RG_DSI_LNT_IMP_CAL_CODE (0xf << 4)
-#define RG_DSI_LNT_AIO_SEL (7 << 8)
-#define RG_DSI_PAD_TIE_LOW_EN BIT(11)
-#define RG_DSI_DEBUG_INPUT_EN BIT(12)
-#define RG_DSI_PRESERVE (7 << 13)
-
-#define MIPITX_DSI_BG_CON 0x44
-#define RG_DSI_BG_CORE_EN BIT(0)
-#define RG_DSI_BG_CKEN BIT(1)
-#define RG_DSI_BG_DIV (0x3 << 2)
-#define RG_DSI_BG_FAST_CHARGE BIT(4)
-#define RG_DSI_VOUT_MSK (0x3ffff << 5)
-#define RG_DSI_V12_SEL (7 << 5)
-#define RG_DSI_V10_SEL (7 << 8)
-#define RG_DSI_V072_SEL (7 << 11)
-#define RG_DSI_V04_SEL (7 << 14)
-#define RG_DSI_V032_SEL (7 << 17)
-#define RG_DSI_V02_SEL (7 << 20)
-#define RG_DSI_BG_R1_TRIM (0xf << 24)
-#define RG_DSI_BG_R2_TRIM (0xf << 28)
-
-#define MIPITX_DSI_PLL_CON0 0x50
-#define RG_DSI_MPPLL_PLL_EN BIT(0)
-#define RG_DSI_MPPLL_DIV_MSK (0x1ff << 1)
-#define RG_DSI_MPPLL_PREDIV (3 << 1)
-#define RG_DSI_MPPLL_TXDIV0 (3 << 3)
-#define RG_DSI_MPPLL_TXDIV1 (3 << 5)
-#define RG_DSI_MPPLL_POSDIV (7 << 7)
-#define RG_DSI_MPPLL_MONVC_EN BIT(10)
-#define RG_DSI_MPPLL_MONREF_EN BIT(11)
-#define RG_DSI_MPPLL_VOD_EN BIT(12)
-
-#define MIPITX_DSI_PLL_CON1 0x54
-#define RG_DSI_MPPLL_SDM_FRA_EN BIT(0)
-#define RG_DSI_MPPLL_SDM_SSC_PH_INIT BIT(1)
-#define RG_DSI_MPPLL_SDM_SSC_EN BIT(2)
-#define RG_DSI_MPPLL_SDM_SSC_PRD (0xffff << 16)
-
-#define MIPITX_DSI_PLL_CON2 0x58
-
-#define MIPITX_DSI_PLL_TOP 0x64
-#define RG_DSI_MPPLL_PRESERVE (0xff << 8)
-
-#define MIPITX_DSI_PLL_PWR 0x68
-#define RG_DSI_MPPLL_SDM_PWR_ON BIT(0)
-#define RG_DSI_MPPLL_SDM_ISO_EN BIT(1)
-#define RG_DSI_MPPLL_SDM_PWR_ACK BIT(8)
-
-#define MIPITX_DSI_SW_CTRL 0x80
-#define SW_CTRL_EN BIT(0)
-
-#define MIPITX_DSI_SW_CTRL_CON0 0x84
-#define SW_LNTC_LPTX_PRE_OE BIT(0)
-#define SW_LNTC_LPTX_OE BIT(1)
-#define SW_LNTC_LPTX_P BIT(2)
-#define SW_LNTC_LPTX_N BIT(3)
-#define SW_LNTC_HSTX_PRE_OE BIT(4)
-#define SW_LNTC_HSTX_OE BIT(5)
-#define SW_LNTC_HSTX_ZEROCLK BIT(6)
-#define SW_LNT0_LPTX_PRE_OE BIT(7)
-#define SW_LNT0_LPTX_OE BIT(8)
-#define SW_LNT0_LPTX_P BIT(9)
-#define SW_LNT0_LPTX_N BIT(10)
-#define SW_LNT0_HSTX_PRE_OE BIT(11)
-#define SW_LNT0_HSTX_OE BIT(12)
-#define SW_LNT0_LPRX_EN BIT(13)
-#define SW_LNT1_LPTX_PRE_OE BIT(14)
-#define SW_LNT1_LPTX_OE BIT(15)
-#define SW_LNT1_LPTX_P BIT(16)
-#define SW_LNT1_LPTX_N BIT(17)
-#define SW_LNT1_HSTX_PRE_OE BIT(18)
-#define SW_LNT1_HSTX_OE BIT(19)
-#define SW_LNT2_LPTX_PRE_OE BIT(20)
-#define SW_LNT2_LPTX_OE BIT(21)
-#define SW_LNT2_LPTX_P BIT(22)
-#define SW_LNT2_LPTX_N BIT(23)
-#define SW_LNT2_HSTX_PRE_OE BIT(24)
-#define SW_LNT2_HSTX_OE BIT(25)
-
-struct mtk_mipitx_data {
- const u32 mppll_preserve;
-};
-
-struct mtk_mipi_tx {
- struct device *dev;
- void __iomem *regs;
- u32 data_rate;
- const struct mtk_mipitx_data *driver_data;
- struct clk_hw pll_hw;
- struct clk *pll;
-};
+#include "mtk_mipi_tx.h"
-static inline struct mtk_mipi_tx *mtk_mipi_tx_from_clk_hw(struct clk_hw *hw)
+inline struct mtk_mipi_tx *mtk_mipi_tx_from_clk_hw(struct clk_hw *hw)
{
return container_of(hw, struct mtk_mipi_tx, pll_hw);
}
-static void mtk_mipi_tx_clear_bits(struct mtk_mipi_tx *mipi_tx, u32 offset,
- u32 bits)
+void mtk_mipi_tx_clear_bits(struct mtk_mipi_tx *mipi_tx, u32 offset,
+ u32 bits)
{
u32 temp = readl(mipi_tx->regs + offset);
writel(temp & ~bits, mipi_tx->regs + offset);
}
-static void mtk_mipi_tx_set_bits(struct mtk_mipi_tx *mipi_tx, u32 offset,
- u32 bits)
+void mtk_mipi_tx_set_bits(struct mtk_mipi_tx *mipi_tx, u32 offset,
+ u32 bits)
{
u32 temp = readl(mipi_tx->regs + offset);
writel(temp | bits, mipi_tx->regs + offset);
}
-static void mtk_mipi_tx_update_bits(struct mtk_mipi_tx *mipi_tx, u32 offset,
- u32 mask, u32 data)
+void mtk_mipi_tx_update_bits(struct mtk_mipi_tx *mipi_tx, u32 offset,
+ u32 mask, u32 data)
{
u32 temp = readl(mipi_tx->regs + offset);
writel((temp & ~mask) | (data & mask), mipi_tx->regs + offset);
}
-static int mtk_mipi_tx_pll_prepare(struct clk_hw *hw)
-{
- struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
- u8 txdiv, txdiv0, txdiv1;
- u64 pcw;
-
- dev_dbg(mipi_tx->dev, "prepare: %u Hz\n", mipi_tx->data_rate);
-
- if (mipi_tx->data_rate >= 500000000) {
- txdiv = 1;
- txdiv0 = 0;
- txdiv1 = 0;
- } else if (mipi_tx->data_rate >= 250000000) {
- txdiv = 2;
- txdiv0 = 1;
- txdiv1 = 0;
- } else if (mipi_tx->data_rate >= 125000000) {
- txdiv = 4;
- txdiv0 = 2;
- txdiv1 = 0;
- } else if (mipi_tx->data_rate > 62000000) {
- txdiv = 8;
- txdiv0 = 2;
- txdiv1 = 1;
- } else if (mipi_tx->data_rate >= 50000000) {
- txdiv = 16;
- txdiv0 = 2;
- txdiv1 = 2;
- } else {
- return -EINVAL;
- }
-
- mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_BG_CON,
- RG_DSI_VOUT_MSK |
- RG_DSI_BG_CKEN | RG_DSI_BG_CORE_EN,
- (4 << 20) | (4 << 17) | (4 << 14) |
- (4 << 11) | (4 << 8) | (4 << 5) |
- RG_DSI_BG_CKEN | RG_DSI_BG_CORE_EN);
-
- usleep_range(30, 100);
-
- mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_TOP_CON,
- RG_DSI_LNT_IMP_CAL_CODE | RG_DSI_LNT_HS_BIAS_EN,
- (8 << 4) | RG_DSI_LNT_HS_BIAS_EN);
-
- mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_CON,
- RG_DSI_CKG_LDOOUT_EN | RG_DSI_LDOCORE_EN);
-
- mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_PWR,
- RG_DSI_MPPLL_SDM_PWR_ON |
- RG_DSI_MPPLL_SDM_ISO_EN,
- RG_DSI_MPPLL_SDM_PWR_ON);
-
- mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
- RG_DSI_MPPLL_PLL_EN);
-
- mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
- RG_DSI_MPPLL_TXDIV0 | RG_DSI_MPPLL_TXDIV1 |
- RG_DSI_MPPLL_PREDIV,
- (txdiv0 << 3) | (txdiv1 << 5));
-
- /*
- * PLL PCW config
- * PCW bit 24~30 = integer part of pcw
- * PCW bit 0~23 = fractional part of pcw
- * pcw = data_Rate*4*txdiv/(Ref_clk*2);
- * Post DIV =4, so need data_Rate*4
- * Ref_clk is 26MHz
- */
- pcw = div_u64(((u64)mipi_tx->data_rate * 2 * txdiv) << 24,
- 26000000);
- writel(pcw, mipi_tx->regs + MIPITX_DSI_PLL_CON2);
-
- mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_PLL_CON1,
- RG_DSI_MPPLL_SDM_FRA_EN);
-
- mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_PLL_CON0, RG_DSI_MPPLL_PLL_EN);
-
- usleep_range(20, 100);
-
- mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_PLL_CON1,
- RG_DSI_MPPLL_SDM_SSC_EN);
-
- mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_TOP,
- RG_DSI_MPPLL_PRESERVE,
- mipi_tx->driver_data->mppll_preserve);
-
- return 0;
-}
-
-static void mtk_mipi_tx_pll_unprepare(struct clk_hw *hw)
-{
- struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
-
- dev_dbg(mipi_tx->dev, "unprepare\n");
-
- mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
- RG_DSI_MPPLL_PLL_EN);
-
- mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_TOP,
- RG_DSI_MPPLL_PRESERVE, 0);
-
- mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_PWR,
- RG_DSI_MPPLL_SDM_ISO_EN |
- RG_DSI_MPPLL_SDM_PWR_ON,
- RG_DSI_MPPLL_SDM_ISO_EN);
-
- mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_TOP_CON,
- RG_DSI_LNT_HS_BIAS_EN);
-
- mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_CON,
- RG_DSI_CKG_LDOOUT_EN | RG_DSI_LDOCORE_EN);
-
- mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_BG_CON,
- RG_DSI_BG_CKEN | RG_DSI_BG_CORE_EN);
-
- mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
- RG_DSI_MPPLL_DIV_MSK);
-}
-
-static long mtk_mipi_tx_pll_round_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long *prate)
-{
- return clamp_val(rate, 50000000, 1250000000);
-}
-
-static int mtk_mipi_tx_pll_set_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long parent_rate)
+int mtk_mipi_tx_pll_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
{
struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
@@ -307,37 +54,14 @@ static int mtk_mipi_tx_pll_set_rate(struct clk_hw *hw, unsigned long rate,
return 0;
}
-static unsigned long mtk_mipi_tx_pll_recalc_rate(struct clk_hw *hw,
- unsigned long parent_rate)
+unsigned long mtk_mipi_tx_pll_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
{
struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
return mipi_tx->data_rate;
}
-static const struct clk_ops mtk_mipi_tx_pll_ops = {
- .prepare = mtk_mipi_tx_pll_prepare,
- .unprepare = mtk_mipi_tx_pll_unprepare,
- .round_rate = mtk_mipi_tx_pll_round_rate,
- .set_rate = mtk_mipi_tx_pll_set_rate,
- .recalc_rate = mtk_mipi_tx_pll_recalc_rate,
-};
-
-static int mtk_mipi_tx_power_on_signal(struct phy *phy)
-{
- struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
- u32 reg;
-
- for (reg = MIPITX_DSI_CLOCK_LANE;
- reg <= MIPITX_DSI_DATA_LANE3; reg += 4)
- mtk_mipi_tx_set_bits(mipi_tx, reg, RG_DSI_LNTx_LDOOUT_EN);
-
- mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_TOP_CON,
- RG_DSI_PAD_TIE_LOW_EN);
-
- return 0;
-}
-
static int mtk_mipi_tx_power_on(struct phy *phy)
{
struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
@@ -349,30 +73,16 @@ static int mtk_mipi_tx_power_on(struct phy *phy)
return ret;
/* Enable DSI Lane LDO outputs, disable pad tie low */
- mtk_mipi_tx_power_on_signal(phy);
-
+ mipi_tx->driver_data->mipi_tx_enable_signal(phy);
return 0;
}
-static void mtk_mipi_tx_power_off_signal(struct phy *phy)
-{
- struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
- u32 reg;
-
- mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_TOP_CON,
- RG_DSI_PAD_TIE_LOW_EN);
-
- for (reg = MIPITX_DSI_CLOCK_LANE;
- reg <= MIPITX_DSI_DATA_LANE3; reg += 4)
- mtk_mipi_tx_clear_bits(mipi_tx, reg, RG_DSI_LNTx_LDOOUT_EN);
-}
-
static int mtk_mipi_tx_power_off(struct phy *phy)
{
struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
/* Enable pad tie low, disable DSI Lane LDO outputs */
- mtk_mipi_tx_power_off_signal(phy);
+ mipi_tx->driver_data->mipi_tx_disable_signal(phy);
/* Disable PLL and power down core */
clk_disable_unprepare(mipi_tx->pll);
@@ -391,10 +101,8 @@ static int mtk_mipi_tx_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct mtk_mipi_tx *mipi_tx;
struct resource *mem;
- struct clk *ref_clk;
const char *ref_clk_name;
struct clk_init_data clk_init = {
- .ops = &mtk_mipi_tx_pll_ops,
.num_parents = 1,
.parent_names = (const char * const *)&ref_clk_name,
.flags = CLK_SET_RATE_GATE,
@@ -408,6 +116,7 @@ static int mtk_mipi_tx_probe(struct platform_device *pdev)
return -ENOMEM;
mipi_tx->driver_data = of_device_get_match_data(dev);
+
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
mipi_tx->regs = devm_ioremap_resource(dev, mem);
if (IS_ERR(mipi_tx->regs)) {
@@ -416,13 +125,14 @@ static int mtk_mipi_tx_probe(struct platform_device *pdev)
return ret;
}
- ref_clk = devm_clk_get(dev, NULL);
- if (IS_ERR(ref_clk)) {
- ret = PTR_ERR(ref_clk);
+ mipi_tx->ref_clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(mipi_tx->ref_clk)) {
+ ret = PTR_ERR(mipi_tx->ref_clk);
dev_err(dev, "Failed to get reference clock: %d\n", ret);
return ret;
}
- ref_clk_name = __clk_get_name(ref_clk);
+
+ ref_clk_name = __clk_get_name(mipi_tx->ref_clk);
ret = of_property_read_string(dev->of_node, "clock-output-names",
&clk_init.name);
@@ -431,6 +141,8 @@ static int mtk_mipi_tx_probe(struct platform_device *pdev)
return ret;
}
+ clk_init.ops = mipi_tx->driver_data->mipi_tx_clk_ops;
+
mipi_tx->pll_hw.init = &clk_init;
mipi_tx->pll = devm_clk_register(dev, &mipi_tx->pll_hw);
if (IS_ERR(mipi_tx->pll)) {
@@ -465,20 +177,12 @@ static int mtk_mipi_tx_remove(struct platform_device *pdev)
return 0;
}
-static const struct mtk_mipitx_data mt2701_mipitx_data = {
- .mppll_preserve = (3 << 8)
-};
-
-static const struct mtk_mipitx_data mt8173_mipitx_data = {
- .mppll_preserve = (0 << 8)
-};
-
static const struct of_device_id mtk_mipi_tx_match[] = {
{ .compatible = "mediatek,mt2701-mipi-tx",
.data = &mt2701_mipitx_data },
{ .compatible = "mediatek,mt8173-mipi-tx",
.data = &mt8173_mipitx_data },
- {},
+ { },
};
struct platform_driver mtk_mipi_tx_driver = {
@@ -489,3 +193,4 @@ struct platform_driver mtk_mipi_tx_driver = {
.of_match_table = mtk_mipi_tx_match,
},
};
+
diff --git a/drivers/gpu/drm/mediatek/mtk_mipi_tx.h b/drivers/gpu/drm/mediatek/mtk_mipi_tx.h
new file mode 100644
index 000000000000..660726924992
--- /dev/null
+++ b/drivers/gpu/drm/mediatek/mtk_mipi_tx.h
@@ -0,0 +1,49 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2019 MediaTek Inc.
+ * Author: Jitao Shi <[email protected]>
+ */
+
+#ifndef _MTK_MIPI_TX_H
+#define _MTK_MIPI_TX_H
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+
+struct mtk_mipitx_data {
+ const u32 mppll_preserve;
+ const struct clk_ops *mipi_tx_clk_ops;
+ void (*mipi_tx_enable_signal)(struct phy *phy);
+ void (*mipi_tx_disable_signal)(struct phy *phy);
+};
+
+struct mtk_mipi_tx {
+ struct device *dev;
+ void __iomem *regs;
+ u32 data_rate;
+ struct clk *ref_clk;
+ const struct mtk_mipitx_data *driver_data;
+ struct clk_hw pll_hw;
+ struct clk *pll;
+};
+
+struct mtk_mipi_tx *mtk_mipi_tx_from_clk_hw(struct clk_hw *hw);
+void mtk_mipi_tx_clear_bits(struct mtk_mipi_tx *mipi_tx, u32 offset, u32 bits);
+void mtk_mipi_tx_set_bits(struct mtk_mipi_tx *mipi_tx, u32 offset, u32 bits);
+void mtk_mipi_tx_update_bits(struct mtk_mipi_tx *mipi_tx, u32 offset, u32 mask,
+ u32 data);
+int mtk_mipi_tx_pll_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate);
+unsigned long mtk_mipi_tx_pll_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate);
+
+extern const struct mtk_mipitx_data mt2701_mipitx_data;
+extern const struct mtk_mipitx_data mt8173_mipitx_data;
+
+#endif
diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_mipi_tx.c b/drivers/gpu/drm/mediatek/mtk_mt8173_mipi_tx.c
new file mode 100644
index 000000000000..95ef0c5252b9
--- /dev/null
+++ b/drivers/gpu/drm/mediatek/mtk_mt8173_mipi_tx.c
@@ -0,0 +1,289 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 MediaTek Inc.
+ * Author: jitao.shi <[email protected]>
+ */
+
+#include "mtk_mipi_tx.h"
+
+#define MIPITX_DSI_CON 0x00
+#define RG_DSI_LDOCORE_EN BIT(0)
+#define RG_DSI_CKG_LDOOUT_EN BIT(1)
+#define RG_DSI_BCLK_SEL (3 << 2)
+#define RG_DSI_LD_IDX_SEL (7 << 4)
+#define RG_DSI_PHYCLK_SEL (2 << 8)
+#define RG_DSI_DSICLK_FREQ_SEL BIT(10)
+#define RG_DSI_LPTX_CLMP_EN BIT(11)
+
+#define MIPITX_DSI_CLOCK_LANE 0x04
+#define MIPITX_DSI_DATA_LANE0 0x08
+#define MIPITX_DSI_DATA_LANE1 0x0c
+#define MIPITX_DSI_DATA_LANE2 0x10
+#define MIPITX_DSI_DATA_LANE3 0x14
+#define RG_DSI_LNTx_LDOOUT_EN BIT(0)
+#define RG_DSI_LNTx_CKLANE_EN BIT(1)
+#define RG_DSI_LNTx_LPTX_IPLUS1 BIT(2)
+#define RG_DSI_LNTx_LPTX_IPLUS2 BIT(3)
+#define RG_DSI_LNTx_LPTX_IMINUS BIT(4)
+#define RG_DSI_LNTx_LPCD_IPLUS BIT(5)
+#define RG_DSI_LNTx_LPCD_IMINUS BIT(6)
+#define RG_DSI_LNTx_RT_CODE (0xf << 8)
+
+#define MIPITX_DSI_TOP_CON 0x40
+#define RG_DSI_LNT_INTR_EN BIT(0)
+#define RG_DSI_LNT_HS_BIAS_EN BIT(1)
+#define RG_DSI_LNT_IMP_CAL_EN BIT(2)
+#define RG_DSI_LNT_TESTMODE_EN BIT(3)
+#define RG_DSI_LNT_IMP_CAL_CODE (0xf << 4)
+#define RG_DSI_LNT_AIO_SEL (7 << 8)
+#define RG_DSI_PAD_TIE_LOW_EN BIT(11)
+#define RG_DSI_DEBUG_INPUT_EN BIT(12)
+#define RG_DSI_PRESERVE (7 << 13)
+
+#define MIPITX_DSI_BG_CON 0x44
+#define RG_DSI_BG_CORE_EN BIT(0)
+#define RG_DSI_BG_CKEN BIT(1)
+#define RG_DSI_BG_DIV (0x3 << 2)
+#define RG_DSI_BG_FAST_CHARGE BIT(4)
+#define RG_DSI_VOUT_MSK (0x3ffff << 5)
+#define RG_DSI_V12_SEL (7 << 5)
+#define RG_DSI_V10_SEL (7 << 8)
+#define RG_DSI_V072_SEL (7 << 11)
+#define RG_DSI_V04_SEL (7 << 14)
+#define RG_DSI_V032_SEL (7 << 17)
+#define RG_DSI_V02_SEL (7 << 20)
+#define RG_DSI_BG_R1_TRIM (0xf << 24)
+#define RG_DSI_BG_R2_TRIM (0xf << 28)
+
+#define MIPITX_DSI_PLL_CON0 0x50
+#define RG_DSI_MPPLL_PLL_EN BIT(0)
+#define RG_DSI_MPPLL_DIV_MSK (0x1ff << 1)
+#define RG_DSI_MPPLL_PREDIV (3 << 1)
+#define RG_DSI_MPPLL_TXDIV0 (3 << 3)
+#define RG_DSI_MPPLL_TXDIV1 (3 << 5)
+#define RG_DSI_MPPLL_POSDIV (7 << 7)
+#define RG_DSI_MPPLL_MONVC_EN BIT(10)
+#define RG_DSI_MPPLL_MONREF_EN BIT(11)
+#define RG_DSI_MPPLL_VOD_EN BIT(12)
+
+#define MIPITX_DSI_PLL_CON1 0x54
+#define RG_DSI_MPPLL_SDM_FRA_EN BIT(0)
+#define RG_DSI_MPPLL_SDM_SSC_PH_INIT BIT(1)
+#define RG_DSI_MPPLL_SDM_SSC_EN BIT(2)
+#define RG_DSI_MPPLL_SDM_SSC_PRD (0xffff << 16)
+
+#define MIPITX_DSI_PLL_CON2 0x58
+
+#define MIPITX_DSI_PLL_TOP 0x64
+#define RG_DSI_MPPLL_PRESERVE (0xff << 8)
+
+#define MIPITX_DSI_PLL_PWR 0x68
+#define RG_DSI_MPPLL_SDM_PWR_ON BIT(0)
+#define RG_DSI_MPPLL_SDM_ISO_EN BIT(1)
+#define RG_DSI_MPPLL_SDM_PWR_ACK BIT(8)
+
+#define MIPITX_DSI_SW_CTRL 0x80
+#define SW_CTRL_EN BIT(0)
+
+#define MIPITX_DSI_SW_CTRL_CON0 0x84
+#define SW_LNTC_LPTX_PRE_OE BIT(0)
+#define SW_LNTC_LPTX_OE BIT(1)
+#define SW_LNTC_LPTX_P BIT(2)
+#define SW_LNTC_LPTX_N BIT(3)
+#define SW_LNTC_HSTX_PRE_OE BIT(4)
+#define SW_LNTC_HSTX_OE BIT(5)
+#define SW_LNTC_HSTX_ZEROCLK BIT(6)
+#define SW_LNT0_LPTX_PRE_OE BIT(7)
+#define SW_LNT0_LPTX_OE BIT(8)
+#define SW_LNT0_LPTX_P BIT(9)
+#define SW_LNT0_LPTX_N BIT(10)
+#define SW_LNT0_HSTX_PRE_OE BIT(11)
+#define SW_LNT0_HSTX_OE BIT(12)
+#define SW_LNT0_LPRX_EN BIT(13)
+#define SW_LNT1_LPTX_PRE_OE BIT(14)
+#define SW_LNT1_LPTX_OE BIT(15)
+#define SW_LNT1_LPTX_P BIT(16)
+#define SW_LNT1_LPTX_N BIT(17)
+#define SW_LNT1_HSTX_PRE_OE BIT(18)
+#define SW_LNT1_HSTX_OE BIT(19)
+#define SW_LNT2_LPTX_PRE_OE BIT(20)
+#define SW_LNT2_LPTX_OE BIT(21)
+#define SW_LNT2_LPTX_P BIT(22)
+#define SW_LNT2_LPTX_N BIT(23)
+#define SW_LNT2_HSTX_PRE_OE BIT(24)
+#define SW_LNT2_HSTX_OE BIT(25)
+
+static int mtk_mipi_tx_pll_prepare(struct clk_hw *hw)
+{
+ struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
+ u8 txdiv, txdiv0, txdiv1;
+ u64 pcw;
+
+ dev_dbg(mipi_tx->dev, "prepare: %u Hz\n", mipi_tx->data_rate);
+
+ if (mipi_tx->data_rate >= 500000000) {
+ txdiv = 1;
+ txdiv0 = 0;
+ txdiv1 = 0;
+ } else if (mipi_tx->data_rate >= 250000000) {
+ txdiv = 2;
+ txdiv0 = 1;
+ txdiv1 = 0;
+ } else if (mipi_tx->data_rate >= 125000000) {
+ txdiv = 4;
+ txdiv0 = 2;
+ txdiv1 = 0;
+ } else if (mipi_tx->data_rate > 62000000) {
+ txdiv = 8;
+ txdiv0 = 2;
+ txdiv1 = 1;
+ } else if (mipi_tx->data_rate >= 50000000) {
+ txdiv = 16;
+ txdiv0 = 2;
+ txdiv1 = 2;
+ } else {
+ return -EINVAL;
+ }
+
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_BG_CON,
+ RG_DSI_VOUT_MSK |
+ RG_DSI_BG_CKEN | RG_DSI_BG_CORE_EN,
+ (4 << 20) | (4 << 17) | (4 << 14) |
+ (4 << 11) | (4 << 8) | (4 << 5) |
+ RG_DSI_BG_CKEN | RG_DSI_BG_CORE_EN);
+
+ usleep_range(30, 100);
+
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_TOP_CON,
+ RG_DSI_LNT_IMP_CAL_CODE | RG_DSI_LNT_HS_BIAS_EN,
+ (8 << 4) | RG_DSI_LNT_HS_BIAS_EN);
+
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_CON,
+ RG_DSI_CKG_LDOOUT_EN | RG_DSI_LDOCORE_EN);
+
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_PWR,
+ RG_DSI_MPPLL_SDM_PWR_ON |
+ RG_DSI_MPPLL_SDM_ISO_EN,
+ RG_DSI_MPPLL_SDM_PWR_ON);
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
+ RG_DSI_MPPLL_PLL_EN);
+
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
+ RG_DSI_MPPLL_TXDIV0 | RG_DSI_MPPLL_TXDIV1 |
+ RG_DSI_MPPLL_PREDIV,
+ (txdiv0 << 3) | (txdiv1 << 5));
+
+ /*
+ * PLL PCW config
+ * PCW bit 24~30 = integer part of pcw
+ * PCW bit 0~23 = fractional part of pcw
+ * pcw = data_Rate*4*txdiv/(Ref_clk*2);
+ * Post DIV =4, so need data_Rate*4
+ * Ref_clk is 26MHz
+ */
+ pcw = div_u64(((u64)mipi_tx->data_rate * 2 * txdiv) << 24,
+ 26000000);
+ writel(pcw, mipi_tx->regs + MIPITX_DSI_PLL_CON2);
+
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_PLL_CON1,
+ RG_DSI_MPPLL_SDM_FRA_EN);
+
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_PLL_CON0, RG_DSI_MPPLL_PLL_EN);
+
+ usleep_range(20, 100);
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_PLL_CON1,
+ RG_DSI_MPPLL_SDM_SSC_EN);
+
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_TOP,
+ RG_DSI_MPPLL_PRESERVE,
+ mipi_tx->driver_data->mppll_preserve);
+
+ return 0;
+}
+
+static void mtk_mipi_tx_pll_unprepare(struct clk_hw *hw)
+{
+ struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
+
+ dev_dbg(mipi_tx->dev, "unprepare\n");
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
+ RG_DSI_MPPLL_PLL_EN);
+
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_TOP,
+ RG_DSI_MPPLL_PRESERVE, 0);
+
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_DSI_PLL_PWR,
+ RG_DSI_MPPLL_SDM_ISO_EN |
+ RG_DSI_MPPLL_SDM_PWR_ON,
+ RG_DSI_MPPLL_SDM_ISO_EN);
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_TOP_CON,
+ RG_DSI_LNT_HS_BIAS_EN);
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_CON,
+ RG_DSI_CKG_LDOOUT_EN | RG_DSI_LDOCORE_EN);
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_BG_CON,
+ RG_DSI_BG_CKEN | RG_DSI_BG_CORE_EN);
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_PLL_CON0,
+ RG_DSI_MPPLL_DIV_MSK);
+}
+
+static long mtk_mipi_tx_pll_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *prate)
+{
+ return clamp_val(rate, 50000000, 1250000000);
+}
+
+static const struct clk_ops mtk_mipi_tx_pll_ops = {
+ .prepare = mtk_mipi_tx_pll_prepare,
+ .unprepare = mtk_mipi_tx_pll_unprepare,
+ .round_rate = mtk_mipi_tx_pll_round_rate,
+ .set_rate = mtk_mipi_tx_pll_set_rate,
+ .recalc_rate = mtk_mipi_tx_pll_recalc_rate,
+};
+
+static void mtk_mipi_tx_power_on_signal(struct phy *phy)
+{
+ struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
+ u32 reg;
+
+ for (reg = MIPITX_DSI_CLOCK_LANE;
+ reg <= MIPITX_DSI_DATA_LANE3; reg += 4)
+ mtk_mipi_tx_set_bits(mipi_tx, reg, RG_DSI_LNTx_LDOOUT_EN);
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_DSI_TOP_CON,
+ RG_DSI_PAD_TIE_LOW_EN);
+}
+
+static void mtk_mipi_tx_power_off_signal(struct phy *phy)
+{
+ struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
+ u32 reg;
+
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_DSI_TOP_CON,
+ RG_DSI_PAD_TIE_LOW_EN);
+
+ for (reg = MIPITX_DSI_CLOCK_LANE;
+ reg <= MIPITX_DSI_DATA_LANE3; reg += 4)
+ mtk_mipi_tx_clear_bits(mipi_tx, reg, RG_DSI_LNTx_LDOOUT_EN);
+}
+
+const struct mtk_mipitx_data mt2701_mipitx_data = {
+ .mppll_preserve = (3 << 8),
+ .mipi_tx_clk_ops = &mtk_mipi_tx_pll_ops,
+ .mipi_tx_enable_signal = mtk_mipi_tx_power_on_signal,
+ .mipi_tx_disable_signal = mtk_mipi_tx_power_off_signal,
+};
+
+const struct mtk_mipitx_data mt8173_mipitx_data = {
+ .mppll_preserve = (0 << 8),
+ .mipi_tx_clk_ops = &mtk_mipi_tx_pll_ops,
+ .mipi_tx_enable_signal = mtk_mipi_tx_power_on_signal,
+ .mipi_tx_disable_signal = mtk_mipi_tx_power_off_signal,
+};
+
--
2.21.0
This patch add mt8183 mipi_tx driver.
And also support other chips that use the same binding and driver.
Signed-off-by: Jitao Shi <[email protected]>
---
drivers/gpu/drm/mediatek/Makefile | 1 +
drivers/gpu/drm/mediatek/mtk_mipi_tx.c | 2 +
drivers/gpu/drm/mediatek/mtk_mipi_tx.h | 1 +
drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c | 181 ++++++++++++++++++
4 files changed, 185 insertions(+)
create mode 100644 drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
diff --git a/drivers/gpu/drm/mediatek/Makefile b/drivers/gpu/drm/mediatek/Makefile
index 2c8de1f5a5ee..8067a4be8311 100644
--- a/drivers/gpu/drm/mediatek/Makefile
+++ b/drivers/gpu/drm/mediatek/Makefile
@@ -13,6 +13,7 @@ mediatek-drm-y := mtk_disp_color.o \
mtk_dsi.o \
mtk_mipi_tx.o \
mtk_mt8173_mipi_tx.o \
+ mtk_mt8183_mipi_tx.o \
mtk_dpi.o
obj-$(CONFIG_DRM_MEDIATEK) += mediatek-drm.o
diff --git a/drivers/gpu/drm/mediatek/mtk_mipi_tx.c b/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
index cdc68b88cefd..ab0fbfba5572 100644
--- a/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
+++ b/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
@@ -182,6 +182,8 @@ static const struct of_device_id mtk_mipi_tx_match[] = {
.data = &mt2701_mipitx_data },
{ .compatible = "mediatek,mt8173-mipi-tx",
.data = &mt8173_mipitx_data },
+ { .compatible = "mediatek,mt8183-mipi-tx",
+ .data = &mt8183_mipitx_data },
{ },
};
diff --git a/drivers/gpu/drm/mediatek/mtk_mipi_tx.h b/drivers/gpu/drm/mediatek/mtk_mipi_tx.h
index 660726924992..3fd24563952e 100644
--- a/drivers/gpu/drm/mediatek/mtk_mipi_tx.h
+++ b/drivers/gpu/drm/mediatek/mtk_mipi_tx.h
@@ -45,5 +45,6 @@ unsigned long mtk_mipi_tx_pll_recalc_rate(struct clk_hw *hw,
extern const struct mtk_mipitx_data mt2701_mipitx_data;
extern const struct mtk_mipitx_data mt8173_mipitx_data;
+extern const struct mtk_mipitx_data mt8183_mipitx_data;
#endif
diff --git a/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c b/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
new file mode 100644
index 000000000000..7758bc95555c
--- /dev/null
+++ b/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 MediaTek Inc.
+ * Author: jitao.shi <[email protected]>
+ */
+
+#include "mtk_mipi_tx.h"
+
+#define MIPITX_LANE_CON 0x000c
+#define RG_DSI_CPHY_T1DRV_EN BIT(0)
+#define RG_DSI_ANA_CK_SEL BIT(1)
+#define RG_DSI_PHY_CK_SEL BIT(2)
+#define RG_DSI_CPHY_EN BIT(3)
+#define RG_DSI_PHYCK_INV_EN BIT(4)
+#define RG_DSI_PWR04_EN BIT(5)
+#define RG_DSI_BG_LPF_EN BIT(6)
+#define RG_DSI_BG_CORE_EN BIT(7)
+#define RG_DSI_PAD_TIEL_SEL BIT(8)
+
+#define MIPITX_PLL_PWR 0x0028
+#define MIPITX_PLL_CON0 0x002c
+#define MIPITX_PLL_CON1 0x0030
+#define MIPITX_PLL_CON2 0x0034
+#define MIPITX_PLL_CON3 0x0038
+#define MIPITX_PLL_CON4 0x003c
+#define RG_DSI_PLL_IBIAS (3 << 10)
+
+#define MIPITX_D2_SW_CTL_EN 0x0144
+#define MIPITX_D0_SW_CTL_EN 0x0244
+#define MIPITX_CK_CKMODE_EN 0x0328
+#define DSI_CK_CKMODE_EN BIT(0)
+#define MIPITX_CK_SW_CTL_EN 0x0344
+#define MIPITX_D1_SW_CTL_EN 0x0444
+#define MIPITX_D3_SW_CTL_EN 0x0544
+#define DSI_SW_CTL_EN BIT(0)
+#define AD_DSI_PLL_SDM_PWR_ON BIT(0)
+#define AD_DSI_PLL_SDM_ISO_EN BIT(1)
+
+#define RG_DSI_PLL_EN BIT(4)
+#define RG_DSI_PLL_POSDIV (0x7 << 8)
+
+static int mtk_mipi_tx_pll_prepare(struct clk_hw *hw)
+{
+ struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
+ int ret = 0;
+
+ ret = clk_prepare(mipi_tx->ref_clk);
+ if (ret < 0)
+ dev_err(mipi_tx->dev,
+ "can't prepare mipi_tx ref_clk %d\n", ret);
+
+ return ret;
+}
+
+static int mtk_mipi_tx_pll_enable(struct clk_hw *hw)
+{
+ struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
+ unsigned int txdiv, txdiv0;
+ u64 pcw;
+ int ret;
+
+ dev_dbg(mipi_tx->dev, "enable: %u bps\n", mipi_tx->data_rate);
+
+ if (mipi_tx->data_rate >= 2000000000) {
+ txdiv = 1;
+ txdiv0 = 0;
+ } else if (mipi_tx->data_rate >= 1000000000) {
+ txdiv = 2;
+ txdiv0 = 1;
+ } else if (mipi_tx->data_rate >= 500000000) {
+ txdiv = 4;
+ txdiv0 = 2;
+ } else if (mipi_tx->data_rate > 250000000) {
+ txdiv = 8;
+ txdiv0 = 3;
+ } else if (mipi_tx->data_rate >= 125000000) {
+ txdiv = 16;
+ txdiv0 = 4;
+ } else {
+ return -EINVAL;
+ }
+
+ ret = clk_enable(mipi_tx->ref_clk);
+ if (ret < 0) {
+ dev_err(mipi_tx->dev,
+ "can't enable mipi_tx ref_clk %d\n", ret);
+ return ret;
+ }
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_CON4, RG_DSI_PLL_IBIAS);
+
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_PLL_PWR, AD_DSI_PLL_SDM_PWR_ON);
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_CON1, RG_DSI_PLL_EN);
+ udelay(1);
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_PWR, AD_DSI_PLL_SDM_ISO_EN);
+ pcw = div_u64(((u64)mipi_tx->data_rate * txdiv) << 24, 26000000);
+ writel(pcw, mipi_tx->regs + MIPITX_PLL_CON0);
+ mtk_mipi_tx_update_bits(mipi_tx, MIPITX_PLL_CON1, RG_DSI_PLL_POSDIV,
+ txdiv0 << 8);
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_PLL_CON1, RG_DSI_PLL_EN);
+
+ return 0;
+}
+
+static void mtk_mipi_tx_pll_unprepare(struct clk_hw *hw)
+{
+ struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
+
+ clk_unprepare(mipi_tx->ref_clk);
+}
+
+static void mtk_mipi_tx_pll_disable(struct clk_hw *hw)
+{
+ struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
+
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_CON1, RG_DSI_PLL_EN);
+
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_PLL_PWR, AD_DSI_PLL_SDM_ISO_EN);
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_PWR, AD_DSI_PLL_SDM_PWR_ON);
+ clk_disable(mipi_tx->ref_clk);
+}
+
+static long mtk_mipi_tx_pll_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *prate)
+{
+ return clamp_val(rate, 50000000, 1600000000);
+}
+
+static const struct clk_ops mtk_mipi_tx_pll_ops = {
+ .prepare = mtk_mipi_tx_pll_prepare,
+ .enable = mtk_mipi_tx_pll_enable,
+ .unprepare = mtk_mipi_tx_pll_unprepare,
+ .disable = mtk_mipi_tx_pll_disable,
+ .round_rate = mtk_mipi_tx_pll_round_rate,
+ .set_rate = mtk_mipi_tx_pll_set_rate,
+ .recalc_rate = mtk_mipi_tx_pll_recalc_rate,
+};
+
+static void mtk_mipi_tx_power_on_signal(struct phy *phy)
+{
+ struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
+
+ /* BG_LPF_EN / BG_CORE_EN */
+ writel(RG_DSI_PAD_TIEL_SEL | RG_DSI_BG_CORE_EN,
+ mipi_tx->regs + MIPITX_LANE_CON);
+ usleep_range(30, 100);
+ writel(RG_DSI_BG_CORE_EN | RG_DSI_BG_LPF_EN,
+ mipi_tx->regs + MIPITX_LANE_CON);
+
+ /* Switch OFF each Lane */
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_D0_SW_CTL_EN, DSI_SW_CTL_EN);
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_D1_SW_CTL_EN, DSI_SW_CTL_EN);
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_D2_SW_CTL_EN, DSI_SW_CTL_EN);
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_D3_SW_CTL_EN, DSI_SW_CTL_EN);
+ mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_CK_SW_CTL_EN, DSI_SW_CTL_EN);
+
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_CK_CKMODE_EN, DSI_CK_CKMODE_EN);
+}
+
+static void mtk_mipi_tx_power_off_signal(struct phy *phy)
+{
+ struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
+
+ /* Switch ON each Lane */
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_D0_SW_CTL_EN, DSI_SW_CTL_EN);
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_D1_SW_CTL_EN, DSI_SW_CTL_EN);
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_D2_SW_CTL_EN, DSI_SW_CTL_EN);
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_D3_SW_CTL_EN, DSI_SW_CTL_EN);
+ mtk_mipi_tx_set_bits(mipi_tx, MIPITX_CK_SW_CTL_EN, DSI_SW_CTL_EN);
+
+ writel(RG_DSI_PAD_TIEL_SEL | RG_DSI_BG_CORE_EN,
+ mipi_tx->regs + MIPITX_LANE_CON);
+ writel(RG_DSI_PAD_TIEL_SEL, mipi_tx->regs + MIPITX_LANE_CON);
+}
+
+const struct mtk_mipitx_data mt8183_mipitx_data = {
+ .mipi_tx_clk_ops = &mtk_mipi_tx_pll_ops,
+ .mipi_tx_enable_signal = mtk_mipi_tx_power_on_signal,
+ .mipi_tx_disable_signal = mtk_mipi_tx_power_off_signal,
+};
+
--
2.21.0
Hi, Jitao:
On Thu, 2019-06-27 at 10:59 +0800, Jitao Shi wrote:
> This patch add mt8183 mipi_tx driver.
> And also support other chips that use the same binding and driver.
>
> Signed-off-by: Jitao Shi <[email protected]>
> ---
> drivers/gpu/drm/mediatek/Makefile | 1 +
> drivers/gpu/drm/mediatek/mtk_mipi_tx.c | 2 +
> drivers/gpu/drm/mediatek/mtk_mipi_tx.h | 1 +
> drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c | 181 ++++++++++++++++++
> 4 files changed, 185 insertions(+)
> create mode 100644 drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
>
> diff --git a/drivers/gpu/drm/mediatek/Makefile b/drivers/gpu/drm/mediatek/Makefile
> index 2c8de1f5a5ee..8067a4be8311 100644
> --- a/drivers/gpu/drm/mediatek/Makefile
> +++ b/drivers/gpu/drm/mediatek/Makefile
> @@ -13,6 +13,7 @@ mediatek-drm-y := mtk_disp_color.o \
> mtk_dsi.o \
> mtk_mipi_tx.o \
> mtk_mt8173_mipi_tx.o \
> + mtk_mt8183_mipi_tx.o \
> mtk_dpi.o
>
> obj-$(CONFIG_DRM_MEDIATEK) += mediatek-drm.o
> diff --git a/drivers/gpu/drm/mediatek/mtk_mipi_tx.c b/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
> index cdc68b88cefd..ab0fbfba5572 100644
> --- a/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
> +++ b/drivers/gpu/drm/mediatek/mtk_mipi_tx.c
> @@ -182,6 +182,8 @@ static const struct of_device_id mtk_mipi_tx_match[] = {
> .data = &mt2701_mipitx_data },
> { .compatible = "mediatek,mt8173-mipi-tx",
> .data = &mt8173_mipitx_data },
> + { .compatible = "mediatek,mt8183-mipi-tx",
> + .data = &mt8183_mipitx_data },
> { },
> };
>
> diff --git a/drivers/gpu/drm/mediatek/mtk_mipi_tx.h b/drivers/gpu/drm/mediatek/mtk_mipi_tx.h
> index 660726924992..3fd24563952e 100644
> --- a/drivers/gpu/drm/mediatek/mtk_mipi_tx.h
> +++ b/drivers/gpu/drm/mediatek/mtk_mipi_tx.h
> @@ -45,5 +45,6 @@ unsigned long mtk_mipi_tx_pll_recalc_rate(struct clk_hw *hw,
>
> extern const struct mtk_mipitx_data mt2701_mipitx_data;
> extern const struct mtk_mipitx_data mt8173_mipitx_data;
> +extern const struct mtk_mipitx_data mt8183_mipitx_data;
>
> #endif
> diff --git a/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c b/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
> new file mode 100644
> index 000000000000..7758bc95555c
> --- /dev/null
> +++ b/drivers/gpu/drm/mediatek/mtk_mt8183_mipi_tx.c
> @@ -0,0 +1,181 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019 MediaTek Inc.
> + * Author: jitao.shi <[email protected]>
> + */
> +
> +#include "mtk_mipi_tx.h"
> +
> +#define MIPITX_LANE_CON 0x000c
> +#define RG_DSI_CPHY_T1DRV_EN BIT(0)
> +#define RG_DSI_ANA_CK_SEL BIT(1)
> +#define RG_DSI_PHY_CK_SEL BIT(2)
> +#define RG_DSI_CPHY_EN BIT(3)
> +#define RG_DSI_PHYCK_INV_EN BIT(4)
> +#define RG_DSI_PWR04_EN BIT(5)
> +#define RG_DSI_BG_LPF_EN BIT(6)
> +#define RG_DSI_BG_CORE_EN BIT(7)
> +#define RG_DSI_PAD_TIEL_SEL BIT(8)
> +
> +#define MIPITX_PLL_PWR 0x0028
> +#define MIPITX_PLL_CON0 0x002c
> +#define MIPITX_PLL_CON1 0x0030
> +#define MIPITX_PLL_CON2 0x0034
> +#define MIPITX_PLL_CON3 0x0038
> +#define MIPITX_PLL_CON4 0x003c
> +#define RG_DSI_PLL_IBIAS (3 << 10)
> +
> +#define MIPITX_D2_SW_CTL_EN 0x0144
> +#define MIPITX_D0_SW_CTL_EN 0x0244
> +#define MIPITX_CK_CKMODE_EN 0x0328
> +#define DSI_CK_CKMODE_EN BIT(0)
> +#define MIPITX_CK_SW_CTL_EN 0x0344
> +#define MIPITX_D1_SW_CTL_EN 0x0444
> +#define MIPITX_D3_SW_CTL_EN 0x0544
> +#define DSI_SW_CTL_EN BIT(0)
> +#define AD_DSI_PLL_SDM_PWR_ON BIT(0)
> +#define AD_DSI_PLL_SDM_ISO_EN BIT(1)
> +
> +#define RG_DSI_PLL_EN BIT(4)
> +#define RG_DSI_PLL_POSDIV (0x7 << 8)
> +
> +static int mtk_mipi_tx_pll_prepare(struct clk_hw *hw)
> +{
> + struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
> + int ret = 0;
> +
> + ret = clk_prepare(mipi_tx->ref_clk);
In mtk_mipi_tx_power_on(), it calls
clk_prepare_enable(mipi_tx->pll);
This function break into
clk_prepare(mipi_tx->pll);
and
clk_enable(mipi_tx->pll);
In clk_prepare(), it would finally call into clk_core_prepare() [1], and
you could see
ret = clk_core_prepare(core->parent);
if (core->ops->prepare)
ret = core->ops->prepare(core->hw);
This mean, before this clock is prepare, ccf would prepare its parent
clock, so you need not to prepare parent clock in this clock's prepare
callback function.
[1]
https://elixir.bootlin.com/linux/v5.2-rc6/source/drivers/clk/clk.c#L836
> + if (ret < 0)
> + dev_err(mipi_tx->dev,
> + "can't prepare mipi_tx ref_clk %d\n", ret);
> +
> + return ret;
> +}
> +
> +static int mtk_mipi_tx_pll_enable(struct clk_hw *hw)
> +{
> + struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
> + unsigned int txdiv, txdiv0;
> + u64 pcw;
> + int ret;
> +
> + dev_dbg(mipi_tx->dev, "enable: %u bps\n", mipi_tx->data_rate);
> +
> + if (mipi_tx->data_rate >= 2000000000) {
> + txdiv = 1;
> + txdiv0 = 0;
> + } else if (mipi_tx->data_rate >= 1000000000) {
> + txdiv = 2;
> + txdiv0 = 1;
> + } else if (mipi_tx->data_rate >= 500000000) {
> + txdiv = 4;
> + txdiv0 = 2;
> + } else if (mipi_tx->data_rate > 250000000) {
> + txdiv = 8;
> + txdiv0 = 3;
> + } else if (mipi_tx->data_rate >= 125000000) {
> + txdiv = 16;
> + txdiv0 = 4;
> + } else {
> + return -EINVAL;
> + }
> +
> + ret = clk_enable(mipi_tx->ref_clk);
Ditto.
Regards,
CK
> + if (ret < 0) {
> + dev_err(mipi_tx->dev,
> + "can't enable mipi_tx ref_clk %d\n", ret);
> + return ret;
> + }
> +
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_CON4, RG_DSI_PLL_IBIAS);
> +
> + mtk_mipi_tx_set_bits(mipi_tx, MIPITX_PLL_PWR, AD_DSI_PLL_SDM_PWR_ON);
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_CON1, RG_DSI_PLL_EN);
> + udelay(1);
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_PWR, AD_DSI_PLL_SDM_ISO_EN);
> + pcw = div_u64(((u64)mipi_tx->data_rate * txdiv) << 24, 26000000);
> + writel(pcw, mipi_tx->regs + MIPITX_PLL_CON0);
> + mtk_mipi_tx_update_bits(mipi_tx, MIPITX_PLL_CON1, RG_DSI_PLL_POSDIV,
> + txdiv0 << 8);
> + mtk_mipi_tx_set_bits(mipi_tx, MIPITX_PLL_CON1, RG_DSI_PLL_EN);
> +
> + return 0;
> +}
> +
> +static void mtk_mipi_tx_pll_unprepare(struct clk_hw *hw)
> +{
> + struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
> +
> + clk_unprepare(mipi_tx->ref_clk);
> +}
> +
> +static void mtk_mipi_tx_pll_disable(struct clk_hw *hw)
> +{
> + struct mtk_mipi_tx *mipi_tx = mtk_mipi_tx_from_clk_hw(hw);
> +
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_CON1, RG_DSI_PLL_EN);
> +
> + mtk_mipi_tx_set_bits(mipi_tx, MIPITX_PLL_PWR, AD_DSI_PLL_SDM_ISO_EN);
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_PLL_PWR, AD_DSI_PLL_SDM_PWR_ON);
> + clk_disable(mipi_tx->ref_clk);
> +}
> +
> +static long mtk_mipi_tx_pll_round_rate(struct clk_hw *hw, unsigned long rate,
> + unsigned long *prate)
> +{
> + return clamp_val(rate, 50000000, 1600000000);
> +}
> +
> +static const struct clk_ops mtk_mipi_tx_pll_ops = {
> + .prepare = mtk_mipi_tx_pll_prepare,
> + .enable = mtk_mipi_tx_pll_enable,
> + .unprepare = mtk_mipi_tx_pll_unprepare,
> + .disable = mtk_mipi_tx_pll_disable,
> + .round_rate = mtk_mipi_tx_pll_round_rate,
> + .set_rate = mtk_mipi_tx_pll_set_rate,
> + .recalc_rate = mtk_mipi_tx_pll_recalc_rate,
> +};
> +
> +static void mtk_mipi_tx_power_on_signal(struct phy *phy)
> +{
> + struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
> +
> + /* BG_LPF_EN / BG_CORE_EN */
> + writel(RG_DSI_PAD_TIEL_SEL | RG_DSI_BG_CORE_EN,
> + mipi_tx->regs + MIPITX_LANE_CON);
> + usleep_range(30, 100);
> + writel(RG_DSI_BG_CORE_EN | RG_DSI_BG_LPF_EN,
> + mipi_tx->regs + MIPITX_LANE_CON);
> +
> + /* Switch OFF each Lane */
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_D0_SW_CTL_EN, DSI_SW_CTL_EN);
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_D1_SW_CTL_EN, DSI_SW_CTL_EN);
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_D2_SW_CTL_EN, DSI_SW_CTL_EN);
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_D3_SW_CTL_EN, DSI_SW_CTL_EN);
> + mtk_mipi_tx_clear_bits(mipi_tx, MIPITX_CK_SW_CTL_EN, DSI_SW_CTL_EN);
> +
> + mtk_mipi_tx_set_bits(mipi_tx, MIPITX_CK_CKMODE_EN, DSI_CK_CKMODE_EN);
> +}
> +
> +static void mtk_mipi_tx_power_off_signal(struct phy *phy)
> +{
> + struct mtk_mipi_tx *mipi_tx = phy_get_drvdata(phy);
> +
> + /* Switch ON each Lane */
> + mtk_mipi_tx_set_bits(mipi_tx, MIPITX_D0_SW_CTL_EN, DSI_SW_CTL_EN);
> + mtk_mipi_tx_set_bits(mipi_tx, MIPITX_D1_SW_CTL_EN, DSI_SW_CTL_EN);
> + mtk_mipi_tx_set_bits(mipi_tx, MIPITX_D2_SW_CTL_EN, DSI_SW_CTL_EN);
> + mtk_mipi_tx_set_bits(mipi_tx, MIPITX_D3_SW_CTL_EN, DSI_SW_CTL_EN);
> + mtk_mipi_tx_set_bits(mipi_tx, MIPITX_CK_SW_CTL_EN, DSI_SW_CTL_EN);
> +
> + writel(RG_DSI_PAD_TIEL_SEL | RG_DSI_BG_CORE_EN,
> + mipi_tx->regs + MIPITX_LANE_CON);
> + writel(RG_DSI_PAD_TIEL_SEL, mipi_tx->regs + MIPITX_LANE_CON);
> +}
> +
> +const struct mtk_mipitx_data mt8183_mipitx_data = {
> + .mipi_tx_clk_ops = &mtk_mipi_tx_pll_ops,
> + .mipi_tx_enable_signal = mtk_mipi_tx_power_on_signal,
> + .mipi_tx_disable_signal = mtk_mipi_tx_power_off_signal,
> +};
> +
Hi, Jitao:
On Thu, 2019-06-27 at 10:59 +0800, Jitao Shi wrote:
> Different IC has different mipi_tx setting of dsi.
> This patch separates the mipi_tx hardware relate part for mt8173.
>
> Signed-off-by: Jitao Shi <[email protected]>
> Reviewed-by: CK Hu <[email protected]>
> ---
> drivers/gpu/drm/mediatek/Makefile | 1 +
> drivers/gpu/drm/mediatek/mtk_mipi_tx.c | 343 ++----------------
> drivers/gpu/drm/mediatek/mtk_mipi_tx.h | 49 +++
> drivers/gpu/drm/mediatek/mtk_mt8173_mipi_tx.c | 289 +++++++++++++++
> 4 files changed, 363 insertions(+), 319 deletions(-)
> create mode 100644 drivers/gpu/drm/mediatek/mtk_mipi_tx.h
> create mode 100644 drivers/gpu/drm/mediatek/mtk_mt8173_mipi_tx.c
>
[snip]
> @@ -391,10 +101,8 @@ static int mtk_mipi_tx_probe(struct platform_device *pdev)
> struct device *dev = &pdev->dev;
> struct mtk_mipi_tx *mipi_tx;
> struct resource *mem;
> - struct clk *ref_clk;
> const char *ref_clk_name;
> struct clk_init_data clk_init = {
> - .ops = &mtk_mipi_tx_pll_ops,
> .num_parents = 1,
> .parent_names = (const char * const *)&ref_clk_name,
> .flags = CLK_SET_RATE_GATE,
> @@ -408,6 +116,7 @@ static int mtk_mipi_tx_probe(struct platform_device *pdev)
> return -ENOMEM;
>
> mipi_tx->driver_data = of_device_get_match_data(dev);
> +
> mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> mipi_tx->regs = devm_ioremap_resource(dev, mem);
> if (IS_ERR(mipi_tx->regs)) {
> @@ -416,13 +125,14 @@ static int mtk_mipi_tx_probe(struct platform_device *pdev)
> return ret;
> }
>
> - ref_clk = devm_clk_get(dev, NULL);
> - if (IS_ERR(ref_clk)) {
> - ret = PTR_ERR(ref_clk);
> + mipi_tx->ref_clk = devm_clk_get(dev, NULL);
I think you need not to keep ref_clk in driver private data because you
would not use it any more.
Regards,
CK
> + if (IS_ERR(mipi_tx->ref_clk)) {
> + ret = PTR_ERR(mipi_tx->ref_clk);
> dev_err(dev, "Failed to get reference clock: %d\n", ret);
> return ret;
> }
> - ref_clk_name = __clk_get_name(ref_clk);
> +
> + ref_clk_name = __clk_get_name(mipi_tx->ref_clk);
>
> ret = of_property_read_string(dev->of_node, "clock-output-names",
> &clk_init.name);
> @@ -431,6 +141,8 @@ static int mtk_mipi_tx_probe(struct platform_device *pdev)
> return ret;
> }
>
> + clk_init.ops = mipi_tx->driver_data->mipi_tx_clk_ops;
> +
> mipi_tx->pll_hw.init = &clk_init;
> mipi_tx->pll = devm_clk_register(dev, &mipi_tx->pll_hw);
> if (IS_ERR(mipi_tx->pll)) {
> @@ -465,20 +177,12 @@ static int mtk_mipi_tx_remove(struct platform_device *pdev)
> return 0;
> }
>
Hi, Jitao:
On Thu, 2019-06-27 at 10:58 +0800, Jitao Shi wrote:
> Update device tree binding documentation for the dsi for
> Mediatek MT8183 SoCs.
>
> Signed-off-by: Jitao Shi <[email protected]>
> Acked-by: Rob Herring <[email protected]>
This version is different than previous version, so I think you should
remove the Acked-by tag. Or Rob could give a tag again on this patch.
Regards,
CK
> ---
> .../devicetree/bindings/display/mediatek/mediatek,dsi.txt | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
> index fadf327c7cdf..a19a6cc375ed 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
> @@ -7,7 +7,7 @@ channel output.
>
> Required properties:
> - compatible: "mediatek,<chip>-dsi"
> - the supported chips are mt2701 and mt8173.
> + the supported chips are mt2701, mt8173 and mt8183.
> - reg: Physical base address and length of the controller's registers
> - interrupts: The interrupt signal from the function block.
> - clocks: device clocks
> @@ -26,7 +26,7 @@ The MIPI TX configuration module controls the MIPI D-PHY.
>
> Required properties:
> - compatible: "mediatek,<chip>-mipi-tx"
> - the supported chips are mt2701 and mt8173.
> + the supported chips are mt2701, mt8173 and mt8183.
> - reg: Physical base address and length of the controller's registers
> - clocks: PLL reference clock
> - clock-output-names: name of the output clock line to the DSI encoder