Hi,
This series adds support for another General Electric patient
monitor series (similar to existing Bx50v3), which is based on
i.MX6DL using Congatec's QMX6 module.
The module uses an I2C RTC to provide the i.MX6 32768 Hz clock,
so it's important to keep it enabled. Not doing so results in
incorrect timings of watchdog and i.MX6 RTC. The bootloader
enables the watchdog, so disabling the clock results in system
reboot. [0]
The second patch is required for B155v2, which uses a 1366x768
G156XTN01 panel. The 1366 width is not supported by the display
pipeline and result in boot hanging without the patch. [1]
Patches 3+4 are updating DT bindings for the new board compatible
values.
Patch 5 adds the board files.
Changes since PATCHv1:
* https://lore.kernel.org/lkml/[email protected]/
* drop patch 5 (applied)
* instead of using 'protected-clocks' in RTC node, add fixed-clock
node as suggested by Saravana Kannan
* rebased to current master (68a32ba14177)
Thanks,
[0] There has been a discussion for the problem on the mailinglists
last year. The discussion died off, when I told people their ideas
don't work. I hope using protected-clocks is fine for this usecase.
https://lore.kernel.org/linux-clk/[email protected]/
[1] I've sent this before as a separate patch in September, but
nobody seemed to care. This adds full context for the problem.
https://lore.kernel.org/dri-devel/[email protected]/
-- Sebastian
Sebastian Reichel (5):
rtc: m41t80: add support for fixed clock
drm/imx: Add 8 pixel alignment fix
dt-bindings: vendor-prefixes: add congatec
dt-bindings: arm: fsl: add GE B1x5pv2 boards
ARM: dts: imx6: Add GE B1x5v2
.../devicetree/bindings/arm/fsl.yaml | 11 +
.../devicetree/bindings/rtc/rtc-m41t80.txt | 9 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/imx6dl-b105pv2.dts | 35 +
arch/arm/boot/dts/imx6dl-b105v2.dts | 35 +
arch/arm/boot/dts/imx6dl-b125pv2.dts | 33 +
arch/arm/boot/dts/imx6dl-b125v2.dts | 33 +
arch/arm/boot/dts/imx6dl-b155v2.dts | 36 +
arch/arm/boot/dts/imx6dl-b1x5pv2.dtsi | 434 ++++++++++++
arch/arm/boot/dts/imx6dl-b1x5v2.dtsi | 61 ++
arch/arm/boot/dts/imx6dl-qmx6.dtsi | 624 ++++++++++++++++++
drivers/gpu/drm/imx/imx-drm-core.c | 19 +-
drivers/gpu/drm/imx/imx-ldb.c | 5 +
drivers/gpu/drm/imx/ipuv3-crtc.c | 11 +-
drivers/gpu/drm/imx/ipuv3-plane.c | 19 +-
drivers/gpu/ipu-v3/ipu-dc.c | 5 +
drivers/gpu/ipu-v3/ipu-di.c | 7 +
drivers/rtc/rtc-m41t80.c | 12 +
19 files changed, 1390 insertions(+), 6 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6dl-b105pv2.dts
create mode 100644 arch/arm/boot/dts/imx6dl-b105v2.dts
create mode 100644 arch/arm/boot/dts/imx6dl-b125pv2.dts
create mode 100644 arch/arm/boot/dts/imx6dl-b125v2.dts
create mode 100644 arch/arm/boot/dts/imx6dl-b155v2.dts
create mode 100644 arch/arm/boot/dts/imx6dl-b1x5pv2.dtsi
create mode 100644 arch/arm/boot/dts/imx6dl-b1x5v2.dtsi
create mode 100644 arch/arm/boot/dts/imx6dl-qmx6.dtsi
--
2.30.2
On Thu, 29 Apr 2021 00:29:48 +0200, Sebastian Reichel wrote:
> This series adds support for another General Electric patient
> monitor series (similar to existing Bx50v3), which is based on
> i.MX6DL using Congatec's QMX6 module.
>
> The module uses an I2C RTC to provide the i.MX6 32768 Hz clock,
> so it's important to keep it enabled. Not doing so results in
> incorrect timings of watchdog and i.MX6 RTC. The bootloader
> enables the watchdog, so disabling the clock results in system
> reboot. [0]
>
> [...]
Applied, thanks!
[1/5] rtc: m41t80: add support for fixed clock
commit: f765e349c3e1f2e676ad4bd61197216b26976022
Best regards,
--
Alexandre Belloni <[email protected]>