This series adds a new devfreq driver for the MBUS/DRAM controller in
some Allwinner SoCs, and enables it for the A64 and H5.
The binding and DTs are updated in patches 1-5. The MBUS nodes already
existed, but were not bound to any driver before; they were only used
for their dma-ranges property. Finally, the driver is added in patch 6.
I am not quite sure the best way to handle DRAM register range in the
DT binding -- as a separate reg property, a separate node, or simply
enlarging the MBUS register range. While the DRAM controller is a
separate IP block, the MBUS hardware has the ability to double-buffer
certain DRAM controller registers, and the hardware MDFS process writes
to some DRAM controller registers as well. So they are rather tightly
integrated.
Like the driver commit description says, this driver could support
additional SoCs: at least A33, A83T, and H3. I can send follow-up
patches adding compatibles for these, but I cannot test A33 or A83T.
Changes from v1:
- Patch 1 was merged
- Drop patches 2-4 (support for devfreq drivers without OPPs)
- Convert the driver to use dynamic OPPs
Samuel Holland (6):
dt-bindings: clock: sunxi: Export CLK_DRAM for devfreq
dt-bindings: arm: sunxi: Expand MBUS binding
dt-bindings: arm: sunxi: Add H5 MBUS compatible
ARM: dts: sunxi: h3/h5: Update MBUS node
arm64: dts: allwinner: a64: Update MBUS node
PM / devfreq: Add a driver for the sun8i/sun50i MBUS
.../arm/sunxi/allwinner,sun4i-a10-mbus.yaml | 77 ++-
arch/arm/boot/dts/sun8i-h3.dtsi | 4 +
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 11 +-
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 10 +-
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 4 +
drivers/clk/sunxi-ng/ccu-sun50i-a64.h | 2 -
drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 2 -
drivers/devfreq/Kconfig | 8 +
drivers/devfreq/Makefile | 1 +
drivers/devfreq/sun8i-a33-mbus.c | 511 ++++++++++++++++++
include/dt-bindings/clock/sun50i-a64-ccu.h | 2 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 2 +-
12 files changed, 620 insertions(+), 14 deletions(-)
create mode 100644 drivers/devfreq/sun8i-a33-mbus.c
--
2.32.0
The MBUS node needs to reference the CLK_DRAM clock, as the MBUS
hardware implements memory dynamic frequency scaling using this clock.
Export this clock for SoCs which will be getting a devfreq driver.
Signed-off-by: Samuel Holland <[email protected]>
---
drivers/clk/sunxi-ng/ccu-sun50i-a64.h | 2 --
drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 2 --
include/dt-bindings/clock/sun50i-a64-ccu.h | 2 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 2 +-
4 files changed, 2 insertions(+), 6 deletions(-)
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a64.h b/drivers/clk/sunxi-ng/ccu-sun50i-a64.h
index 54d1f96f4b68..a8c11c0b4e06 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-a64.h
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a64.h
@@ -51,8 +51,6 @@
#define CLK_USB_OHCI1_12M 92
-#define CLK_DRAM 94
-
/* All the DRAM gates are exported */
/* And the DSI and GPU module clock is exported */
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
index d8c38447e11b..e13f3c4b57d0 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
@@ -42,8 +42,6 @@
/* The first bunch of module clocks are exported */
-#define CLK_DRAM 96
-
/* All the DRAM gates are exported */
/* Some more module clocks are exported */
diff --git a/include/dt-bindings/clock/sun50i-a64-ccu.h b/include/dt-bindings/clock/sun50i-a64-ccu.h
index 318eb15c414c..175892189e9d 100644
--- a/include/dt-bindings/clock/sun50i-a64-ccu.h
+++ b/include/dt-bindings/clock/sun50i-a64-ccu.h
@@ -113,7 +113,7 @@
#define CLK_USB_OHCI0 91
#define CLK_USB_OHCI1 93
-
+#define CLK_DRAM 94
#define CLK_DRAM_VE 95
#define CLK_DRAM_CSI 96
#define CLK_DRAM_DEINTERLACE 97
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
index 30d2d15373a2..5d4ada2c22e6 100644
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -126,7 +126,7 @@
#define CLK_USB_OHCI1 93
#define CLK_USB_OHCI2 94
#define CLK_USB_OHCI3 95
-
+#define CLK_DRAM 96
#define CLK_DRAM_VE 97
#define CLK_DRAM_CSI 98
#define CLK_DRAM_DEINTERLACE 99
--
2.32.0
The MBUS provides more than address translation and bandwidth control.
It also provides a PMU to measure bandwidth usage by certain masters,
and it provides notification via IRQ when they are active or idle.
The MBUS is also tightly integrated with the DRAM controller to provide
a Memory Dynamic Frequency Scaling (MDFS) feature. In view of this, the
MBUS binding needs to represent the hardware resources needed for MDFS,
which include the clocks and MMIO range of the adjacent DRAM controller.
Add the additional resources for the H3 and A64 compatibles, and a new
example showing how they are used.
Signed-off-by: Samuel Holland <[email protected]>
---
.../arm/sunxi/allwinner,sun4i-a10-mbus.yaml | 75 ++++++++++++++++++-
1 file changed, 72 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
index e713a6fe4cf7..c1fb404d2fb3 100644
--- a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
@@ -33,10 +33,33 @@ properties:
- allwinner,sun50i-a64-mbus
reg:
- maxItems: 1
+ minItems: 1
+ items:
+ - description: MBUS interconnect/bandwidth/PMU registers
+ - description: DRAM controller/PHY registers
+
+ reg-names:
+ items:
+ - const: "mbus"
+ - const: "dram"
clocks:
+ minItems: 1
+ items:
+ - description: MBUS interconnect module clock
+ - description: DRAM controller/PHY module clock
+ - description: Register bus clock, shared by MBUS and DRAM
+
+ clock-names:
+ items:
+ - const: "mbus"
+ - const: "dram"
+ - const: "bus"
+
+ interrupts:
maxItems: 1
+ description:
+ MBUS PMU activity interrupt.
dma-ranges:
description:
@@ -53,13 +76,42 @@ required:
- clocks
- dma-ranges
+if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - allwinner,sun8i-h3-mbus
+ - allwinner,sun50i-a64-mbus
+
+then:
+ properties:
+ reg:
+ minItems: 2
+
+ clocks:
+ minItems: 3
+
+ required:
+ - reg-names
+ - clock-names
+
+else:
+ properties:
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
additionalProperties: false
examples:
- |
- #include <dt-bindings/clock/sun5i-ccu.h>
+ #include <dt-bindings/clock/sun50i-a64-ccu.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
- mbus: dram-controller@1c01000 {
+ dram-controller@1c01000 {
compatible = "allwinner,sun5i-a13-mbus";
reg = <0x01c01000 0x1000>;
clocks = <&ccu CLK_MBUS>;
@@ -69,4 +121,21 @@ examples:
#interconnect-cells = <1>;
};
+ - |
+ dram-controller@1c62000 {
+ compatible = "allwinner,sun50i-a64-mbus";
+ reg = <0x01c62000 0x1000>,
+ <0x01c63000 0x1000>;
+ reg-names = "mbus", "dram";
+ clocks = <&ccu CLK_MBUS>,
+ <&ccu CLK_DRAM>,
+ <&ccu CLK_BUS_DRAM>;
+ clock-names = "mbus", "dram", "bus";
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ dma-ranges = <0x00000000 0x40000000 0xc0000000>;
+ #interconnect-cells = <1>;
+ };
+
...
--
2.32.0
In order to support memory dynamic frequency scaling (MDFS), the MBUS
binding now requires enumerating more resources. Provide them in the
device tree.
Since the H3 and H5 have different clock divider limits, they need
separate compatibles.
Signed-off-by: Samuel Holland <[email protected]>
---
arch/arm/boot/dts/sun8i-h3.dtsi | 4 ++++
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 11 ++++++++---
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 4 ++++
3 files changed, 16 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 4e89701df91f..43acb98cf390 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -282,6 +282,10 @@ &display_clocks {
compatible = "allwinner,sun8i-h3-de2-clk";
};
+&mbus {
+ compatible = "allwinner,sun8i-h3-mbus";
+};
+
&mmc0 {
compatible = "allwinner,sun7i-a20-mmc";
clocks = <&ccu CLK_BUS_MMC0>,
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index c7428df9469e..3a683e190dab 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -568,9 +568,14 @@ external_mdio: mdio@2 {
};
mbus: dram-controller@1c62000 {
- compatible = "allwinner,sun8i-h3-mbus";
- reg = <0x01c62000 0x1000>;
- clocks = <&ccu CLK_MBUS>;
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c62000 0x1000>,
+ <0x01c63000 0x1000>;
+ reg-names = "mbus", "dram";
+ clocks = <&ccu CLK_MBUS>,
+ <&ccu CLK_DRAM>,
+ <&ccu CLK_BUS_DRAM>;
+ clock-names = "mbus", "dram", "bus";
#address-cells = <1>;
#size-cells = <1>;
dma-ranges = <0x00000000 0x40000000 0xc0000000>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
index 578a63dedf46..35d5d238e313 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -233,6 +233,10 @@ &display_clocks {
compatible = "allwinner,sun50i-h5-de2-clk";
};
+&mbus {
+ compatible = "allwinner,sun50i-h5-mbus";
+};
+
&mmc0 {
compatible = "allwinner,sun50i-h5-mmc",
"allwinner,sun50i-a64-mmc";
--
2.32.0
In order to support memory dynamic frequency scaling (MDFS), the MBUS
binding now requires enumerating more resources. Provide them in the
device tree.
Signed-off-by: Samuel Holland <[email protected]>
---
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 10 ++++++++--
1 file changed, 8 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 6ddb717f2f98..609a59c6c778 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -1129,8 +1129,14 @@ pwm: pwm@1c21400 {
mbus: dram-controller@1c62000 {
compatible = "allwinner,sun50i-a64-mbus";
- reg = <0x01c62000 0x1000>;
- clocks = <&ccu 112>;
+ reg = <0x01c62000 0x1000>,
+ <0x01c63000 0x1000>;
+ reg-names = "mbus", "dram";
+ clocks = <&ccu CLK_MBUS>,
+ <&ccu CLK_DRAM>,
+ <&ccu CLK_BUS_DRAM>;
+ clock-names = "mbus", "dram", "bus";
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <1>;
dma-ranges = <0x00000000 0x40000000 0xc0000000>;
--
2.32.0
The H5 SoC has a MBUS very similar to the H3 SoC, but it has a smaller
MDFS divider range (1-4 instead of 1-16). Add a separate compatible for
this variant.
Signed-off-by: Samuel Holland <[email protected]>
---
.../devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
index c1fb404d2fb3..c070f99e0bb7 100644
--- a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
@@ -31,6 +31,7 @@ properties:
- allwinner,sun5i-a13-mbus
- allwinner,sun8i-h3-mbus
- allwinner,sun50i-a64-mbus
+ - allwinner,sun50i-h5-mbus
reg:
minItems: 1
@@ -83,6 +84,7 @@ if:
enum:
- allwinner,sun8i-h3-mbus
- allwinner,sun50i-a64-mbus
+ - allwinner,sun50i-h5-mbus
then:
properties:
--
2.32.0
This driver works by adjusting the divider on the DRAM controller's
module clock. Thus there is no fixed set of OPPs, only "full speed" down
to "quarter speed" (or whatever the maximum divider is on that variant).
It makes use of the MDFS hardware in the MBUS, in "DFS" mode, which
takes care of updating registers during the critical section while DRAM
is inaccessible.
This driver should support several sunxi SoCs, starting with the A33,
which have a DesignWare DDR3 controller with merged PHY register space
and the matching MBUS register layout (so not A63 or later). However,
the driver has only been tested on the A64/H5, so those are the only
compatibles enabled for now.
Signed-off-by: Samuel Holland <[email protected]>
---
drivers/devfreq/Kconfig | 8 +
drivers/devfreq/Makefile | 1 +
drivers/devfreq/sun8i-a33-mbus.c | 511 +++++++++++++++++++++++++++++++
3 files changed, 520 insertions(+)
create mode 100644 drivers/devfreq/sun8i-a33-mbus.c
diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
index e87d01c0b76a..b94eb04761f6 100644
--- a/drivers/devfreq/Kconfig
+++ b/drivers/devfreq/Kconfig
@@ -132,6 +132,14 @@ config ARM_RK3399_DMC_DEVFREQ
It sets the frequency for the memory controller and reads the usage counts
from hardware.
+config ARM_SUN8I_A33_MBUS_DEVFREQ
+ tristate "sun8i/sun50i MBUS DEVFREQ Driver"
+ depends on ARCH_SUNXI || COMPILE_TEST
+ select DEVFREQ_GOV_SIMPLE_ONDEMAND
+ help
+ This adds the DEVFREQ driver for the MBUS controller in some
+ Allwinner sun8i (A33 through H3) and sun50i (A64 and H5) SoCs.
+
source "drivers/devfreq/event/Kconfig"
endif # PM_DEVFREQ
diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile
index a16333ea7034..0b6be92a25d9 100644
--- a/drivers/devfreq/Makefile
+++ b/drivers/devfreq/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ) += exynos-bus.o
obj-$(CONFIG_ARM_IMX_BUS_DEVFREQ) += imx-bus.o
obj-$(CONFIG_ARM_IMX8M_DDRC_DEVFREQ) += imx8m-ddrc.o
obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ) += rk3399_dmc.o
+obj-$(CONFIG_ARM_SUN8I_A33_MBUS_DEVFREQ) += sun8i-a33-mbus.o
obj-$(CONFIG_ARM_TEGRA_DEVFREQ) += tegra30-devfreq.o
# DEVFREQ Event Drivers
diff --git a/drivers/devfreq/sun8i-a33-mbus.c b/drivers/devfreq/sun8i-a33-mbus.c
new file mode 100644
index 000000000000..13d32213139f
--- /dev/null
+++ b/drivers/devfreq/sun8i-a33-mbus.c
@@ -0,0 +1,511 @@
+// SPDX-License-Identifier: GPL-2.0-only
+//
+// Copyright (C) 2020-2021 Samuel Holland <[email protected]>
+//
+
+#include <linux/clk.h>
+#include <linux/devfreq.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+
+#define MBUS_CR 0x0000
+#define MBUS_CR_GET_DRAM_TYPE(x) (((x) >> 16) & 0x7)
+#define MBUS_CR_DRAM_TYPE_DDR2 2
+#define MBUS_CR_DRAM_TYPE_DDR3 3
+#define MBUS_CR_DRAM_TYPE_DDR4 4
+#define MBUS_CR_DRAM_TYPE_LPDDR2 6
+#define MBUS_CR_DRAM_TYPE_LPDDR3 7
+
+#define MBUS_TMR 0x000c
+#define MBUS_TMR_PERIOD(x) ((x) - 1)
+
+#define MBUS_PMU_CFG 0x009c
+#define MBUS_PMU_CFG_PERIOD(x) (((x) - 1) << 16)
+#define MBUS_PMU_CFG_UNIT (0x3 << 1)
+#define MBUS_PMU_CFG_UNIT_B (0x0 << 1)
+#define MBUS_PMU_CFG_UNIT_KB (0x1 << 1)
+#define MBUS_PMU_CFG_UNIT_MB (0x2 << 1)
+#define MBUS_PMU_CFG_ENABLE (0x1 << 0)
+
+#define MBUS_PMU_BWCR(n) (0x00a0 + (0x04 * (n)))
+
+#define MBUS_TOTAL_BWCR MBUS_PMU_BWCR(5)
+#define MBUS_TOTAL_BWCR_H616 MBUS_PMU_BWCR(13)
+
+#define MBUS_MDFSCR 0x0100
+#define MBUS_MDFSCR_BUFFER_TIMING (0x1 << 15)
+#define MBUS_MDFSCR_PAD_HOLD (0x1 << 13)
+#define MBUS_MDFSCR_BYPASS (0x1 << 4)
+#define MBUS_MDFSCR_MODE (0x1 << 1)
+#define MBUS_MDFSCR_MODE_DFS (0x0 << 1)
+#define MBUS_MDFSCR_MODE_CFS (0x1 << 1)
+#define MBUS_MDFSCR_START (0x1 << 0)
+
+#define MBUS_MDFSMRMR 0x0108
+
+#define DRAM_PWRCTL 0x0004
+#define DRAM_PWRCTL_SELFREF_EN (0x1 << 0)
+
+#define DRAM_RFSHTMG 0x0090
+#define DRAM_RFSHTMG_TREFI(x) ((x) << 16)
+#define DRAM_RFSHTMG_TRFC(x) ((x) << 0)
+
+#define DRAM_VTFCR 0x00b8
+#define DRAM_VTFCR_VTF_ENABLE (0x3 << 8)
+
+#define DRAM_ODTMAP 0x0120
+
+#define DRAM_DX_MAX 4
+
+#define DRAM_DXnGCR0(n) (0x0344 + 0x80 * (n))
+#define DRAM_DXnGCR0_DXODT (0x3 << 4)
+#define DRAM_DXnGCR0_DXODT_DYNAMIC (0x0 << 4)
+#define DRAM_DXnGCR0_DXODT_ENABLED (0x1 << 4)
+#define DRAM_DXnGCR0_DXODT_DISABLED (0x2 << 4)
+#define DRAM_DXnGCR0_DXEN (0x1 << 0)
+
+struct sun8i_a33_mbus_variant {
+ u32 min_dram_divider;
+ u32 max_dram_divider;
+ u32 odt_freq_mhz;
+};
+
+struct sun8i_a33_mbus {
+ const struct sun8i_a33_mbus_variant *variant;
+ void __iomem *reg_dram;
+ void __iomem *reg_mbus;
+ struct clk *clk_bus;
+ struct clk *clk_dram;
+ struct clk *clk_mbus;
+ struct devfreq *devfreq_dram;
+ struct devfreq_simple_ondemand_data gov_data;
+ struct devfreq_dev_profile profile;
+ u32 data_width;
+ u32 nominal_bw;
+ u32 odtmap;
+ u32 tREFI_ns;
+ u32 tRFC_ns;
+ unsigned long freq_table[];
+};
+
+/*
+ * The unit for this value is (MBUS clock cycles / MBUS_TMR_PERIOD). When
+ * MBUS_TMR_PERIOD is programmed to match the MBUS clock frequency in MHz, as
+ * it is during DRAM init and during probe, the resulting unit is microseconds.
+ */
+static int pmu_period = 50000;
+module_param(pmu_period, int, 0644);
+MODULE_PARM_DESC(pmu_period, "Bandwidth measurement period (microseconds)");
+
+static u32 sun8i_a33_mbus_get_peak_bw(struct sun8i_a33_mbus *priv)
+{
+ /* Returns the peak transfer (in KiB) during any single PMU period. */
+ return readl_relaxed(priv->reg_mbus + MBUS_TOTAL_BWCR);
+}
+
+static void sun8i_a33_mbus_restart_pmu_counters(struct sun8i_a33_mbus *priv)
+{
+ u32 pmu_cfg = MBUS_PMU_CFG_PERIOD(pmu_period) | MBUS_PMU_CFG_UNIT_KB;
+
+ /* All PMU counters are cleared on a disable->enable transition. */
+ writel_relaxed(pmu_cfg,
+ priv->reg_mbus + MBUS_PMU_CFG);
+ writel_relaxed(pmu_cfg | MBUS_PMU_CFG_ENABLE,
+ priv->reg_mbus + MBUS_PMU_CFG);
+
+}
+
+static void sun8i_a33_mbus_update_nominal_bw(struct sun8i_a33_mbus *priv,
+ u32 ddr_freq_mhz)
+{
+ /*
+ * Nominal bandwidth (KiB per PMU period):
+ *
+ * DDR transfers microseconds KiB
+ * ------------- * ------------ * --------
+ * microsecond PMU period transfer
+ */
+ priv->nominal_bw = ddr_freq_mhz * pmu_period * priv->data_width / 1024;
+}
+
+static int sun8i_a33_mbus_set_dram_freq(struct sun8i_a33_mbus *priv,
+ unsigned long freq)
+{
+ u32 ddr_freq_mhz = freq / USEC_PER_SEC; /* DDR */
+ u32 dram_freq_mhz = ddr_freq_mhz / 2; /* SDR */
+ u32 mctl_freq_mhz = dram_freq_mhz / 2; /* HDR */
+ u32 dxodt, mdfscr, pwrctl, vtfcr;
+ u32 i, tREFI_32ck, tRFC_ck;
+ int ret;
+
+ /* The rate change is not effective until the MDFS process runs. */
+ ret = clk_set_rate(priv->clk_dram, freq);
+ if (ret)
+ return ret;
+
+ /* Disable automatic self-refesh and VTF before starting MDFS. */
+ pwrctl = readl_relaxed(priv->reg_dram + DRAM_PWRCTL) &
+ ~DRAM_PWRCTL_SELFREF_EN;
+ writel_relaxed(pwrctl, priv->reg_dram + DRAM_PWRCTL);
+ vtfcr = readl_relaxed(priv->reg_dram + DRAM_VTFCR);
+ writel_relaxed(vtfcr & ~DRAM_VTFCR_VTF_ENABLE,
+ priv->reg_dram + DRAM_VTFCR);
+
+ /* Set up MDFS and enable double buffering for timing registers. */
+ mdfscr = MBUS_MDFSCR_MODE_DFS |
+ MBUS_MDFSCR_BYPASS |
+ MBUS_MDFSCR_PAD_HOLD |
+ MBUS_MDFSCR_BUFFER_TIMING;
+ writel(mdfscr, priv->reg_mbus + MBUS_MDFSCR);
+
+ /* Update the buffered copy of RFSHTMG. */
+ tREFI_32ck = priv->tREFI_ns * mctl_freq_mhz / 1000 / 32;
+ tRFC_ck = DIV_ROUND_UP(priv->tRFC_ns * mctl_freq_mhz, 1000);
+ writel(DRAM_RFSHTMG_TREFI(tREFI_32ck) | DRAM_RFSHTMG_TRFC(tRFC_ck),
+ priv->reg_dram + DRAM_RFSHTMG);
+
+ /* Enable ODT if needed, or disable it to save power. */
+ if (priv->odtmap && dram_freq_mhz > priv->variant->odt_freq_mhz) {
+ dxodt = DRAM_DXnGCR0_DXODT_DYNAMIC;
+ writel(priv->odtmap, priv->reg_dram + DRAM_ODTMAP);
+ } else {
+ dxodt = DRAM_DXnGCR0_DXODT_DISABLED;
+ writel(0, priv->reg_dram + DRAM_ODTMAP);
+ }
+ for (i = 0; i < DRAM_DX_MAX; ++i) {
+ void __iomem *reg = priv->reg_dram + DRAM_DXnGCR0(i);
+
+ writel((readl(reg) & ~DRAM_DXnGCR0_DXODT) | dxodt, reg);
+ }
+
+ dev_dbg(priv->devfreq_dram->dev.parent,
+ "Setting DRAM to %u MHz, tREFI=%u, tRFC=%u, ODT=%s\n",
+ dram_freq_mhz, tREFI_32ck, tRFC_ck,
+ dxodt == DRAM_DXnGCR0_DXODT_DYNAMIC ? "dynamic" : "disabled");
+
+ /* Trigger hardware MDFS. */
+ writel(mdfscr | MBUS_MDFSCR_START, priv->reg_mbus + MBUS_MDFSCR);
+ ret = readl_poll_timeout_atomic(priv->reg_mbus + MBUS_MDFSCR, mdfscr,
+ !(mdfscr & MBUS_MDFSCR_START), 10, 1000);
+ if (ret)
+ return ret;
+
+ /* Disable double buffering. */
+ writel(0, priv->reg_mbus + MBUS_MDFSCR);
+
+ /* Restore VTF configuration. */
+ writel_relaxed(vtfcr, priv->reg_dram + DRAM_VTFCR);
+
+ /* Enable automatic self-refresh at the lowest frequency only. */
+ if (freq == priv->freq_table[0])
+ pwrctl |= DRAM_PWRCTL_SELFREF_EN;
+ writel_relaxed(pwrctl, priv->reg_dram + DRAM_PWRCTL);
+
+ sun8i_a33_mbus_restart_pmu_counters(priv);
+ sun8i_a33_mbus_update_nominal_bw(priv, ddr_freq_mhz);
+
+ return 0;
+}
+
+static int sun8i_a33_mbus_set_dram_target(struct device *dev,
+ unsigned long *freq, u32 flags)
+{
+ struct sun8i_a33_mbus *priv = dev_get_drvdata(dev);
+ struct devfreq *devfreq = priv->devfreq_dram;
+ struct dev_pm_opp *opp;
+ int ret;
+
+ opp = devfreq_recommended_opp(dev, freq, flags);
+ if (IS_ERR(opp))
+ return PTR_ERR(opp);
+
+ dev_pm_opp_put(opp);
+
+ if (*freq == devfreq->previous_freq)
+ return 0;
+
+ ret = sun8i_a33_mbus_set_dram_freq(priv, *freq);
+ if (ret) {
+ dev_warn(dev, "failed to set DRAM frequency: %d\n", ret);
+ *freq = devfreq->previous_freq;
+ }
+
+ return ret;
+}
+
+static int sun8i_a33_mbus_get_dram_status(struct device *dev,
+ struct devfreq_dev_status *stat)
+{
+ struct sun8i_a33_mbus *priv = dev_get_drvdata(dev);
+
+ stat->busy_time = sun8i_a33_mbus_get_peak_bw(priv);
+ stat->total_time = priv->nominal_bw;
+ stat->current_frequency = priv->devfreq_dram->previous_freq;
+
+ sun8i_a33_mbus_restart_pmu_counters(priv);
+
+ dev_dbg(dev, "Using %lu/%lu (%lu%%) at %lu MHz\n",
+ stat->busy_time, stat->total_time,
+ DIV_ROUND_CLOSEST(stat->busy_time * 100, stat->total_time),
+ stat->current_frequency / USEC_PER_SEC);
+
+ return 0;
+}
+
+static int sun8i_a33_mbus_hw_init(struct device *dev,
+ struct sun8i_a33_mbus *priv,
+ unsigned long ddr_freq)
+{
+ u32 i, mbus_cr, mbus_freq_mhz;
+
+ /* Choose tREFI and tRFC to match the configured DRAM type. */
+ mbus_cr = readl_relaxed(priv->reg_mbus + MBUS_CR);
+ switch (MBUS_CR_GET_DRAM_TYPE(mbus_cr)) {
+ case MBUS_CR_DRAM_TYPE_DDR2:
+ case MBUS_CR_DRAM_TYPE_DDR3:
+ case MBUS_CR_DRAM_TYPE_DDR4:
+ priv->tREFI_ns = 7800;
+ priv->tRFC_ns = 350;
+ break;
+ case MBUS_CR_DRAM_TYPE_LPDDR2:
+ case MBUS_CR_DRAM_TYPE_LPDDR3:
+ priv->tREFI_ns = 3900;
+ priv->tRFC_ns = 210;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /* Save ODTMAP so it can be restored when raising the frequency. */
+ priv->odtmap = readl_relaxed(priv->reg_dram + DRAM_ODTMAP);
+
+ /* Compute the DRAM data bus width by counting enabled DATx8 blocks. */
+ for (i = 0; i < DRAM_DX_MAX; ++i) {
+ void __iomem *reg = priv->reg_dram + DRAM_DXnGCR0(i);
+
+ if (!(readl_relaxed(reg) & DRAM_DXnGCR0_DXEN))
+ break;
+ }
+ priv->data_width = i;
+
+ dev_dbg(dev, "Detected %u-bit %sDDRx with%s ODT\n",
+ priv->data_width * 8,
+ MBUS_CR_GET_DRAM_TYPE(mbus_cr) > 4 ? "LP" : "",
+ priv->odtmap ? "" : "out");
+
+ /* Program MBUS_TMR such that the PMU period unit is microseconds. */
+ mbus_freq_mhz = clk_get_rate(priv->clk_mbus) / USEC_PER_SEC;
+ writel_relaxed(MBUS_TMR_PERIOD(mbus_freq_mhz),
+ priv->reg_mbus + MBUS_TMR);
+
+ /* "Master Ready Mask Register" bits must be set or MDFS will block. */
+ writel_relaxed(0xffffffff, priv->reg_mbus + MBUS_MDFSMRMR);
+
+ sun8i_a33_mbus_restart_pmu_counters(priv);
+ sun8i_a33_mbus_update_nominal_bw(priv, ddr_freq / USEC_PER_SEC);
+
+ return 0;
+}
+
+static int __maybe_unused sun8i_a33_mbus_suspend(struct device *dev)
+{
+ struct sun8i_a33_mbus *priv = dev_get_drvdata(dev);
+
+ clk_disable_unprepare(priv->clk_bus);
+
+ return 0;
+}
+
+static int __maybe_unused sun8i_a33_mbus_resume(struct device *dev)
+{
+ struct sun8i_a33_mbus *priv = dev_get_drvdata(dev);
+
+ return clk_prepare_enable(priv->clk_bus);
+}
+
+static int sun8i_a33_mbus_probe(struct platform_device *pdev)
+{
+ const struct sun8i_a33_mbus_variant *variant;
+ struct device *dev = &pdev->dev;
+ struct sun8i_a33_mbus *priv;
+ unsigned long base_freq;
+ unsigned int max_state;
+ const char *err;
+ int i, ret;
+
+ variant = device_get_match_data(dev);
+ if (!variant)
+ return -EINVAL;
+
+ max_state = variant->max_dram_divider - variant->min_dram_divider + 1;
+
+ priv = devm_kzalloc(dev, struct_size(priv, freq_table, max_state), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, priv);
+
+ priv->variant = variant;
+
+ priv->reg_dram = devm_platform_ioremap_resource_byname(pdev, "dram");
+ if (IS_ERR(priv->reg_dram))
+ return PTR_ERR(priv->reg_dram);
+
+ priv->reg_mbus = devm_platform_ioremap_resource_byname(pdev, "mbus");
+ if (IS_ERR(priv->reg_mbus))
+ return PTR_ERR(priv->reg_mbus);
+
+ priv->clk_bus = devm_clk_get(dev, "bus");
+ if (IS_ERR(priv->clk_bus))
+ return dev_err_probe(dev, PTR_ERR(priv->clk_bus),
+ "failed to get bus clock\n");
+
+ priv->clk_dram = devm_clk_get(dev, "dram");
+ if (IS_ERR(priv->clk_dram))
+ return dev_err_probe(dev, PTR_ERR(priv->clk_dram),
+ "failed to get dram clock\n");
+
+ priv->clk_mbus = devm_clk_get(dev, "mbus");
+ if (IS_ERR(priv->clk_mbus))
+ return dev_err_probe(dev, PTR_ERR(priv->clk_mbus),
+ "failed to get mbus clock\n");
+
+ ret = clk_prepare_enable(priv->clk_bus);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "failed to enable bus clock\n");
+
+ /* Lock the DRAM clock rate to keep priv->nominal_bw in sync. */
+ ret = clk_rate_exclusive_get(priv->clk_dram);
+ if (ret) {
+ err = "failed to lock dram clock rate\n";
+ goto err_disable_bus;
+ }
+
+ /* Lock the MBUS clock rate to keep MBUS_TMR_PERIOD in sync. */
+ ret = clk_rate_exclusive_get(priv->clk_mbus);
+ if (ret) {
+ err = "failed to lock mbus clock rate\n";
+ goto err_unlock_dram;
+ }
+
+ priv->gov_data.upthreshold = 10;
+ priv->gov_data.downdifferential = 5;
+
+ priv->profile.initial_freq = clk_get_rate(priv->clk_dram);
+ priv->profile.polling_ms = 1000;
+ priv->profile.target = sun8i_a33_mbus_set_dram_target;
+ priv->profile.get_dev_status = sun8i_a33_mbus_get_dram_status;
+ priv->profile.freq_table = priv->freq_table;
+ priv->profile.max_state = max_state;
+
+ ret = devm_pm_opp_set_clkname(dev, "dram");
+ if (ret) {
+ err = "failed to add OPP table\n";
+ goto err_unlock_mbus;
+ }
+
+ base_freq = clk_get_rate(clk_get_parent(priv->clk_dram));
+ for (i = 0; i < max_state; ++i) {
+ unsigned int div = variant->max_dram_divider - i;
+
+ priv->freq_table[i] = base_freq / div;
+
+ ret = dev_pm_opp_add(dev, priv->freq_table[i], 0);
+ if (ret) {
+ err = "failed to add OPPs\n";
+ goto err_remove_opps;
+ }
+ }
+
+ ret = sun8i_a33_mbus_hw_init(dev, priv, priv->profile.initial_freq);
+ if (ret) {
+ err = "failed to init hardware\n";
+ goto err_remove_opps;
+ }
+
+ priv->devfreq_dram = devfreq_add_device(dev, &priv->profile,
+ DEVFREQ_GOV_SIMPLE_ONDEMAND,
+ &priv->gov_data);
+ if (IS_ERR(priv->devfreq_dram)) {
+ ret = PTR_ERR(priv->devfreq_dram);
+ err = "failed to add devfreq device\n";
+ goto err_remove_opps;
+ }
+
+ /*
+ * This must be set manually after registering the devfreq device,
+ * because there is no way to select a dynamic OPP as the suspend OPP.
+ */
+ priv->devfreq_dram->suspend_freq = priv->freq_table[0];
+
+ return 0;
+
+err_remove_opps:
+ dev_pm_opp_remove_all_dynamic(dev);
+err_unlock_mbus:
+ clk_rate_exclusive_put(priv->clk_mbus);
+err_unlock_dram:
+ clk_rate_exclusive_put(priv->clk_dram);
+err_disable_bus:
+ clk_disable_unprepare(priv->clk_bus);
+
+ return dev_err_probe(dev, ret, err);
+}
+
+static int sun8i_a33_mbus_remove(struct platform_device *pdev)
+{
+ struct sun8i_a33_mbus *priv = platform_get_drvdata(pdev);
+ unsigned long initial_freq = priv->profile.initial_freq;
+ struct device *dev = &pdev->dev;
+ int ret;
+
+ devfreq_remove_device(priv->devfreq_dram);
+
+ ret = sun8i_a33_mbus_set_dram_freq(priv, initial_freq);
+ if (ret)
+ dev_warn(dev, "failed to restore DRAM frequency: %d\n", ret);
+
+ dev_pm_opp_remove_all_dynamic(dev);
+ clk_rate_exclusive_put(priv->clk_mbus);
+ clk_rate_exclusive_put(priv->clk_dram);
+ clk_disable_unprepare(priv->clk_bus);
+
+ return 0;
+}
+
+static const struct sun8i_a33_mbus_variant sun50i_a64_mbus = {
+ .min_dram_divider = 1,
+ .max_dram_divider = 4,
+ .odt_freq_mhz = 400,
+};
+
+static const struct of_device_id sun8i_a33_mbus_of_match[] = {
+ { .compatible = "allwinner,sun50i-a64-mbus", .data = &sun50i_a64_mbus },
+ { .compatible = "allwinner,sun50i-h5-mbus", .data = &sun50i_a64_mbus },
+ { },
+};
+MODULE_DEVICE_TABLE(of, sun8i_a33_mbus_of_match);
+
+static SIMPLE_DEV_PM_OPS(sun8i_a33_mbus_pm_ops,
+ sun8i_a33_mbus_suspend, sun8i_a33_mbus_resume);
+
+static struct platform_driver sun8i_a33_mbus_driver = {
+ .probe = sun8i_a33_mbus_probe,
+ .remove = sun8i_a33_mbus_remove,
+ .driver = {
+ .name = "sun8i-a33-mbus",
+ .of_match_table = sun8i_a33_mbus_of_match,
+ .pm = pm_ptr(&sun8i_a33_mbus_pm_ops),
+ },
+};
+module_platform_driver(sun8i_a33_mbus_driver);
+
+MODULE_AUTHOR("Samuel Holland <[email protected]>");
+MODULE_DESCRIPTION("Allwinner sun8i/sun50i MBUS DEVFREQ Driver");
+MODULE_LICENSE("GPL v2");
--
2.32.0
On Sun, 03 Oct 2021 20:27:36 -0500, Samuel Holland wrote:
> The H5 SoC has a MBUS very similar to the H3 SoC, but it has a smaller
> MDFS divider range (1-4 instead of 1-16). Add a separate compatible for
> this variant.
>
> Signed-off-by: Samuel Holland <[email protected]>
> ---
> .../devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Running 'make dtbs_check' with the schema in this patch gives the
following warnings. Consider if they are expected or the schema is
incorrect. These may not be new warnings.
Note that it is not yet a requirement to have 0 warnings for dtbs_check.
This will change in the future.
Full log is available here: https://patchwork.ozlabs.org/patch/1535893
dram-controller@1c62000: 'clock-names' is a required property
arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-oceanic-5205-5inmfd.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino-emmc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus-v1.2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h3-cc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h3-it.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h5-cc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dt.yaml
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus-v1.2.dt.yaml
arch/arm/boot/dts/sun8i-h3-beelink-x2.dt.yaml
arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dt.yaml
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dt.yaml
arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-m1.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-neo.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-r1.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-2.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-lite.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-one.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dt.yaml
arch/arm/boot/dts/sun8i-h3-rervision-dvk.dt.yaml
arch/arm/boot/dts/sun8i-h3-zeropi.dt.yaml
dram-controller@1c62000: clocks: [[2, 112]] is too short
arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-oceanic-5205-5inmfd.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino-emmc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dt.yaml
dram-controller@1c62000: clocks: [[3, 113]] is too short
arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus-v1.2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h3-cc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h3-it.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h5-cc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dt.yaml
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus-v1.2.dt.yaml
arch/arm/boot/dts/sun8i-h3-beelink-x2.dt.yaml
arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dt.yaml
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dt.yaml
arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-m1.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-neo.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-r1.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-2.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-lite.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-one.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dt.yaml
arch/arm/boot/dts/sun8i-h3-rervision-dvk.dt.yaml
arch/arm/boot/dts/sun8i-h3-zeropi.dt.yaml
dram-controller@1c62000: reg: [[29761536, 4096]] is too short
arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-oceanic-5205-5inmfd.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino-emmc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus-v1.2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h3-cc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h3-it.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h5-cc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dt.yaml
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus-v1.2.dt.yaml
arch/arm/boot/dts/sun8i-h3-beelink-x2.dt.yaml
arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dt.yaml
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dt.yaml
arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-m1.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-neo.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-r1.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-2.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-lite.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-one.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dt.yaml
arch/arm/boot/dts/sun8i-h3-rervision-dvk.dt.yaml
arch/arm/boot/dts/sun8i-h3-zeropi.dt.yaml
dram-controller@1c62000: 'reg-names' is a required property
arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-oceanic-5205-5inmfd.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino-emmc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-bananapi-m2-plus-v1.2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-emlid-neutis-n5-devboard.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h3-cc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h3-it.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-libretech-all-h5-cc.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dt.yaml
arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dt.yaml
arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dt.yaml
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus-v1.2.dt.yaml
arch/arm/boot/dts/sun8i-h3-beelink-x2.dt.yaml
arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dt.yaml
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dt.yaml
arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-m1.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-neo.dt.yaml
arch/arm/boot/dts/sun8i-h3-nanopi-r1.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-2.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-lite.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-one.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dt.yaml
arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dt.yaml
arch/arm/boot/dts/sun8i-h3-rervision-dvk.dt.yaml
arch/arm/boot/dts/sun8i-h3-zeropi.dt.yaml
On Sun, 03 Oct 2021 20:27:34 -0500, Samuel Holland wrote:
> The MBUS node needs to reference the CLK_DRAM clock, as the MBUS
> hardware implements memory dynamic frequency scaling using this clock.
>
> Export this clock for SoCs which will be getting a devfreq driver.
>
> Signed-off-by: Samuel Holland <[email protected]>
> ---
> drivers/clk/sunxi-ng/ccu-sun50i-a64.h | 2 --
> drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 2 --
> include/dt-bindings/clock/sun50i-a64-ccu.h | 2 +-
> include/dt-bindings/clock/sun8i-h3-ccu.h | 2 +-
> 4 files changed, 2 insertions(+), 6 deletions(-)
>
Acked-by: Rob Herring <[email protected]>
On Sun, Oct 03, 2021 at 08:27:35PM -0500, Samuel Holland wrote:
> The MBUS provides more than address translation and bandwidth control.
> It also provides a PMU to measure bandwidth usage by certain masters,
> and it provides notification via IRQ when they are active or idle.
>
> The MBUS is also tightly integrated with the DRAM controller to provide
> a Memory Dynamic Frequency Scaling (MDFS) feature. In view of this, the
> MBUS binding needs to represent the hardware resources needed for MDFS,
> which include the clocks and MMIO range of the adjacent DRAM controller.
>
> Add the additional resources for the H3 and A64 compatibles, and a new
> example showing how they are used.
>
> Signed-off-by: Samuel Holland <[email protected]>
> ---
> .../arm/sunxi/allwinner,sun4i-a10-mbus.yaml | 75 ++++++++++++++++++-
> 1 file changed, 72 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
> index e713a6fe4cf7..c1fb404d2fb3 100644
> --- a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
> +++ b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
> @@ -33,10 +33,33 @@ properties:
> - allwinner,sun50i-a64-mbus
>
> reg:
> - maxItems: 1
> + minItems: 1
> + items:
> + - description: MBUS interconnect/bandwidth/PMU registers
> + - description: DRAM controller/PHY registers
> +
> + reg-names:
> + items:
> + - const: "mbus"
> + - const: "dram"
Don't need quotes.
Is it your intention that reg-names has to have 2 entries. Usually we
aren't that strict and 1 would be allowed (when reg has 1).
>
> clocks:
> + minItems: 1
> + items:
> + - description: MBUS interconnect module clock
> + - description: DRAM controller/PHY module clock
> + - description: Register bus clock, shared by MBUS and DRAM
> +
> + clock-names:
> + items:
> + - const: "mbus"
> + - const: "dram"
> + - const: "bus"
> +
> + interrupts:
> maxItems: 1
> + description:
> + MBUS PMU activity interrupt.
>
> dma-ranges:
> description:
> @@ -53,13 +76,42 @@ required:
> - clocks
> - dma-ranges
>
> +if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - allwinner,sun8i-h3-mbus
> + - allwinner,sun50i-a64-mbus
> +
> +then:
> + properties:
> + reg:
> + minItems: 2
> +
> + clocks:
> + minItems: 3
> +
> + required:
> + - reg-names
> + - clock-names
> +
> +else:
> + properties:
> + reg:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> additionalProperties: false
>
> examples:
> - |
> - #include <dt-bindings/clock/sun5i-ccu.h>
> + #include <dt-bindings/clock/sun50i-a64-ccu.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
>
> - mbus: dram-controller@1c01000 {
> + dram-controller@1c01000 {
> compatible = "allwinner,sun5i-a13-mbus";
> reg = <0x01c01000 0x1000>;
> clocks = <&ccu CLK_MBUS>;
> @@ -69,4 +121,21 @@ examples:
> #interconnect-cells = <1>;
> };
>
> + - |
> + dram-controller@1c62000 {
> + compatible = "allwinner,sun50i-a64-mbus";
> + reg = <0x01c62000 0x1000>,
> + <0x01c63000 0x1000>;
> + reg-names = "mbus", "dram";
> + clocks = <&ccu CLK_MBUS>,
> + <&ccu CLK_DRAM>,
> + <&ccu CLK_BUS_DRAM>;
> + clock-names = "mbus", "dram", "bus";
> + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + dma-ranges = <0x00000000 0x40000000 0xc0000000>;
> + #interconnect-cells = <1>;
> + };
> +
> ...
> --
> 2.32.0
>
>
On Sun, 03 Oct 2021 20:27:36 -0500, Samuel Holland wrote:
> The H5 SoC has a MBUS very similar to the H3 SoC, but it has a smaller
> MDFS divider range (1-4 instead of 1-16). Add a separate compatible for
> this variant.
>
> Signed-off-by: Samuel Holland <[email protected]>
> ---
> .../devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Acked-by: Rob Herring <[email protected]>
On 10/4/21 10:27 AM, Samuel Holland wrote:
> The MBUS node needs to reference the CLK_DRAM clock, as the MBUS
> hardware implements memory dynamic frequency scaling using this clock.
>
> Export this clock for SoCs which will be getting a devfreq driver.
>
> Signed-off-by: Samuel Holland <[email protected]>
> ---
> drivers/clk/sunxi-ng/ccu-sun50i-a64.h | 2 --
> drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 2 --
> include/dt-bindings/clock/sun50i-a64-ccu.h | 2 +-
> include/dt-bindings/clock/sun8i-h3-ccu.h | 2 +-
> 4 files changed, 2 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a64.h b/drivers/clk/sunxi-ng/ccu-sun50i-a64.h
> index 54d1f96f4b68..a8c11c0b4e06 100644
> --- a/drivers/clk/sunxi-ng/ccu-sun50i-a64.h
> +++ b/drivers/clk/sunxi-ng/ccu-sun50i-a64.h
> @@ -51,8 +51,6 @@
>
> #define CLK_USB_OHCI1_12M 92
>
> -#define CLK_DRAM 94
> -
> /* All the DRAM gates are exported */
>
> /* And the DSI and GPU module clock is exported */
> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
> index d8c38447e11b..e13f3c4b57d0 100644
> --- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
> @@ -42,8 +42,6 @@
>
> /* The first bunch of module clocks are exported */
>
> -#define CLK_DRAM 96
> -
> /* All the DRAM gates are exported */
>
> /* Some more module clocks are exported */
> diff --git a/include/dt-bindings/clock/sun50i-a64-ccu.h b/include/dt-bindings/clock/sun50i-a64-ccu.h
> index 318eb15c414c..175892189e9d 100644
> --- a/include/dt-bindings/clock/sun50i-a64-ccu.h
> +++ b/include/dt-bindings/clock/sun50i-a64-ccu.h
> @@ -113,7 +113,7 @@
> #define CLK_USB_OHCI0 91
>
> #define CLK_USB_OHCI1 93
> -
> +#define CLK_DRAM 94
> #define CLK_DRAM_VE 95
> #define CLK_DRAM_CSI 96
> #define CLK_DRAM_DEINTERLACE 97
> diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
> index 30d2d15373a2..5d4ada2c22e6 100644
> --- a/include/dt-bindings/clock/sun8i-h3-ccu.h
> +++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
> @@ -126,7 +126,7 @@
> #define CLK_USB_OHCI1 93
> #define CLK_USB_OHCI2 94
> #define CLK_USB_OHCI3 95
> -
> +#define CLK_DRAM 96
> #define CLK_DRAM_VE 97
> #define CLK_DRAM_CSI 98
> #define CLK_DRAM_DEINTERLACE 99
>
Reviewed-by: Chanwoo Choi <[email protected]>
--
Best Regards,
Chanwoo Choi
Samsung Electronics
Hi Samuel,
On 10/4/21 10:27 AM, Samuel Holland wrote:
> This driver works by adjusting the divider on the DRAM controller's
> module clock. Thus there is no fixed set of OPPs, only "full speed" down
> to "quarter speed" (or whatever the maximum divider is on that variant).
>
> It makes use of the MDFS hardware in the MBUS, in "DFS" mode, which
> takes care of updating registers during the critical section while DRAM
> is inaccessible.
>
> This driver should support several sunxi SoCs, starting with the A33,
> which have a DesignWare DDR3 controller with merged PHY register space
> and the matching MBUS register layout (so not A63 or later). However,
> the driver has only been tested on the A64/H5, so those are the only
> compatibles enabled for now.
>
> Signed-off-by: Samuel Holland <[email protected]>
> ---
> drivers/devfreq/Kconfig | 8 +
> drivers/devfreq/Makefile | 1 +
> drivers/devfreq/sun8i-a33-mbus.c | 511 +++++++++++++++++++++++++++++++
> 3 files changed, 520 insertions(+)
> create mode 100644 drivers/devfreq/sun8i-a33-mbus.c
(snip)
Looks good to me.
Acked-by: Chanwoo Choi <[email protected]>
--
Best Regards,
Chanwoo Choi
Samsung Electronics
On 10/4/21 10:27 AM, Samuel Holland wrote:
> In order to support memory dynamic frequency scaling (MDFS), the MBUS
> binding now requires enumerating more resources. Provide them in the
> device tree.
>
> Signed-off-by: Samuel Holland <[email protected]>
> ---
> arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 10 ++++++++--
> 1 file changed, 8 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> index 6ddb717f2f98..609a59c6c778 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> @@ -1129,8 +1129,14 @@ pwm: pwm@1c21400 {
>
> mbus: dram-controller@1c62000 {
> compatible = "allwinner,sun50i-a64-mbus";
> - reg = <0x01c62000 0x1000>;
> - clocks = <&ccu 112>;
> + reg = <0x01c62000 0x1000>,
> + <0x01c63000 0x1000>;
> + reg-names = "mbus", "dram";
> + clocks = <&ccu CLK_MBUS>,
> + <&ccu CLK_DRAM>,
> + <&ccu CLK_BUS_DRAM>;
> + clock-names = "mbus", "dram", "bus";
> + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
> #address-cells = <1>;
> #size-cells = <1>;
> dma-ranges = <0x00000000 0x40000000 0xc0000000>;
>
Reviewed-by: Chanwoo Choi <[email protected]>
--
Best Regards,
Chanwoo Choi
Samsung Electronics
On 10/4/21 10:27 AM, Samuel Holland wrote:
> In order to support memory dynamic frequency scaling (MDFS), the MBUS
> binding now requires enumerating more resources. Provide them in the
> device tree.
>
> Since the H3 and H5 have different clock divider limits, they need
> separate compatibles.
>
> Signed-off-by: Samuel Holland <[email protected]>
> ---
> arch/arm/boot/dts/sun8i-h3.dtsi | 4 ++++
> arch/arm/boot/dts/sunxi-h3-h5.dtsi | 11 ++++++++---
> arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 4 ++++
> 3 files changed, 16 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> index 4e89701df91f..43acb98cf390 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -282,6 +282,10 @@ &display_clocks {
> compatible = "allwinner,sun8i-h3-de2-clk";
> };
>
> +&mbus {
> + compatible = "allwinner,sun8i-h3-mbus";
> +};
> +
> &mmc0 {
> compatible = "allwinner,sun7i-a20-mmc";
> clocks = <&ccu CLK_BUS_MMC0>,
> diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> index c7428df9469e..3a683e190dab 100644
> --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> @@ -568,9 +568,14 @@ external_mdio: mdio@2 {
> };
>
> mbus: dram-controller@1c62000 {
> - compatible = "allwinner,sun8i-h3-mbus";
> - reg = <0x01c62000 0x1000>;
> - clocks = <&ccu CLK_MBUS>;
> + /* compatible is in per SoC .dtsi file */
> + reg = <0x01c62000 0x1000>,
> + <0x01c63000 0x1000>;
> + reg-names = "mbus", "dram";
> + clocks = <&ccu CLK_MBUS>,
> + <&ccu CLK_DRAM>,
> + <&ccu CLK_BUS_DRAM>;
> + clock-names = "mbus", "dram", "bus";
> #address-cells = <1>;
> #size-cells = <1>;
> dma-ranges = <0x00000000 0x40000000 0xc0000000>;
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
> index 578a63dedf46..35d5d238e313 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
> @@ -233,6 +233,10 @@ &display_clocks {
> compatible = "allwinner,sun50i-h5-de2-clk";
> };
>
> +&mbus {
> + compatible = "allwinner,sun50i-h5-mbus";
> +};
> +
> &mmc0 {
> compatible = "allwinner,sun50i-h5-mmc",
> "allwinner,sun50i-a64-mmc";
>
Reviewed-by: Chanwoo Choi <[email protected]>
--
Best Regards,
Chanwoo Choi
Samsung Electronics
On 10/4/21 10:27 AM, Samuel Holland wrote:
> The MBUS provides more than address translation and bandwidth control.
> It also provides a PMU to measure bandwidth usage by certain masters,
> and it provides notification via IRQ when they are active or idle.
>
> The MBUS is also tightly integrated with the DRAM controller to provide
> a Memory Dynamic Frequency Scaling (MDFS) feature. In view of this, the
> MBUS binding needs to represent the hardware resources needed for MDFS,
> which include the clocks and MMIO range of the adjacent DRAM controller.
>
> Add the additional resources for the H3 and A64 compatibles, and a new
> example showing how they are used.
>
> Signed-off-by: Samuel Holland <[email protected]>
> ---
> .../arm/sunxi/allwinner,sun4i-a10-mbus.yaml | 75 ++++++++++++++++++-
> 1 file changed, 72 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
> index e713a6fe4cf7..c1fb404d2fb3 100644
> --- a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
> +++ b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml
> @@ -33,10 +33,33 @@ properties:
> - allwinner,sun50i-a64-mbus
>
> reg:
> - maxItems: 1
> + minItems: 1
> + items:
> + - description: MBUS interconnect/bandwidth/PMU registers
> + - description: DRAM controller/PHY registers
> +
> + reg-names:
> + items:
> + - const: "mbus"
> + - const: "dram"
>
> clocks:
> + minItems: 1
> + items:
> + - description: MBUS interconnect module clock
> + - description: DRAM controller/PHY module clock
> + - description: Register bus clock, shared by MBUS and DRAM
> +
> + clock-names:
> + items:
> + - const: "mbus"
> + - const: "dram"
> + - const: "bus"
> +
> + interrupts:
> maxItems: 1
> + description:
> + MBUS PMU activity interrupt.
>
> dma-ranges:
> description:
> @@ -53,13 +76,42 @@ required:
> - clocks
> - dma-ranges
>
> +if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - allwinner,sun8i-h3-mbus
> + - allwinner,sun50i-a64-mbus
> +
> +then:
> + properties:
> + reg:
> + minItems: 2
> +
> + clocks:
> + minItems: 3
> +
> + required:
> + - reg-names
> + - clock-names
> +
> +else:
> + properties:
> + reg:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> additionalProperties: false
>
> examples:
> - |
> - #include <dt-bindings/clock/sun5i-ccu.h>
> + #include <dt-bindings/clock/sun50i-a64-ccu.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
>
> - mbus: dram-controller@1c01000 {
> + dram-controller@1c01000 {
> compatible = "allwinner,sun5i-a13-mbus";
> reg = <0x01c01000 0x1000>;
> clocks = <&ccu CLK_MBUS>;
> @@ -69,4 +121,21 @@ examples:
> #interconnect-cells = <1>;
> };
>
> + - |
> + dram-controller@1c62000 {
> + compatible = "allwinner,sun50i-a64-mbus";
> + reg = <0x01c62000 0x1000>,
> + <0x01c63000 0x1000>;
> + reg-names = "mbus", "dram";
> + clocks = <&ccu CLK_MBUS>,
> + <&ccu CLK_DRAM>,
> + <&ccu CLK_BUS_DRAM>;
> + clock-names = "mbus", "dram", "bus";
> + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + dma-ranges = <0x00000000 0x40000000 0xc0000000>;
> + #interconnect-cells = <1>;
> + };
> +
> ...
>
Reviewed-by: Chanwoo Choi <[email protected]>
--
Best Regards,
Chanwoo Choi
Samsung Electronics