After the device has signaled the end of reset by clearing the reset bit,
it will automatically reinit MHI and the internal device structures. Once
That is done, the device will signal it has entered the ready state.
Signaling the ready state involves sending an interrupt (MSI) to the host
which might cause IOMMU faults if it occurs at the wrong time.
If the controller is being powered down, and possibly removed, then the
reset flow would only wait for the end of reset. At which point, the host
and device would start a race. The host may complete its reset work, and
remove the interrupt handler, which would cause the interrupt to be
disabled in the IOMMU. If that occurs before the device signals the ready
state, then the IOMMU will fault since it blocked an interrupt. While
harmless, the fault would appear like a serious issue has occurred so let's
silence it by making sure the device hits the ready state before the host
completes its reset processing.
Signed-off-by: Jeffrey Hugo <[email protected]>
Reviewed-by: Hemant Kumar <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
---
v4:
Cleanup email domain change
v3:
Rebase and use dev_err over dev_warn
v2:
Fix subject and remove use of cur_state
drivers/bus/mhi/host/pm.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/bus/mhi/host/pm.c b/drivers/bus/mhi/host/pm.c
index 3d90b8e..c000a92 100644
--- a/drivers/bus/mhi/host/pm.c
+++ b/drivers/bus/mhi/host/pm.c
@@ -476,6 +476,15 @@ static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl)
* hence re-program it
*/
mhi_write_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_INTVEC, 0);
+
+ if (!MHI_IN_PBL(mhi_get_exec_env(mhi_cntrl))) {
+ /* wait for ready to be set */
+ ret = mhi_poll_reg_field(mhi_cntrl, mhi_cntrl->regs,
+ MHISTATUS,
+ MHISTATUS_READY_MASK, 1, 25000);
+ if (ret)
+ dev_err(dev, "Device failed to enter READY state\n");
+ }
}
dev_dbg(dev,
--
2.7.4
On Mon, Apr 18, 2022 at 11:22:42AM -0600, Jeffrey Hugo wrote:
> After the device has signaled the end of reset by clearing the reset bit,
> it will automatically reinit MHI and the internal device structures. Once
> That is done, the device will signal it has entered the ready state.
>
> Signaling the ready state involves sending an interrupt (MSI) to the host
> which might cause IOMMU faults if it occurs at the wrong time.
>
> If the controller is being powered down, and possibly removed, then the
> reset flow would only wait for the end of reset. At which point, the host
> and device would start a race. The host may complete its reset work, and
> remove the interrupt handler, which would cause the interrupt to be
> disabled in the IOMMU. If that occurs before the device signals the ready
> state, then the IOMMU will fault since it blocked an interrupt. While
> harmless, the fault would appear like a serious issue has occurred so let's
> silence it by making sure the device hits the ready state before the host
> completes its reset processing.
>
> Signed-off-by: Jeffrey Hugo <[email protected]>
> Reviewed-by: Hemant Kumar <[email protected]>
> Reviewed-by: Manivannan Sadhasivam <[email protected]>
Applied to mhi-next!
Thanks,
Mani
> ---
>
> v4:
> Cleanup email domain change
>
> v3:
> Rebase and use dev_err over dev_warn
>
> v2:
> Fix subject and remove use of cur_state
>
> drivers/bus/mhi/host/pm.c | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/drivers/bus/mhi/host/pm.c b/drivers/bus/mhi/host/pm.c
> index 3d90b8e..c000a92 100644
> --- a/drivers/bus/mhi/host/pm.c
> +++ b/drivers/bus/mhi/host/pm.c
> @@ -476,6 +476,15 @@ static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl)
> * hence re-program it
> */
> mhi_write_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_INTVEC, 0);
> +
> + if (!MHI_IN_PBL(mhi_get_exec_env(mhi_cntrl))) {
> + /* wait for ready to be set */
> + ret = mhi_poll_reg_field(mhi_cntrl, mhi_cntrl->regs,
> + MHISTATUS,
> + MHISTATUS_READY_MASK, 1, 25000);
> + if (ret)
> + dev_err(dev, "Device failed to enter READY state\n");
> + }
> }
>
> dev_dbg(dev,
> --
> 2.7.4
>