Bug report from Martin Bruchanov ([email protected], [email protected])
############################################################################
[1.] One line summary of the problem:
USB doesn't work properly with SMP kernel on dual-mainboard or with APIC.
############################################################################
[2.] Full description of the problem/report:
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=18 (error=-110)
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=20 (error=-110)
This message was echoed, when i plug-in SMP device Wacom Graphire or
keyboard to USB plug. I test it with three identicals kernel, only
difference was in "Processor type and features".
There was USB non-functional with Symmetric multi-processing support
was US on fistr kernel.
Second kernel without SMP correctly detect the USB device and without
APIC.
Third kernel with APIC and IO-APIC support on uniprocessors was not
detect USB device.
############################################################################
[3.] Keywords (i.e., modules, networking, kernel):
modules, USB
############################################################################
[4.] Kernel version (from /proc/version):
2.4.2
############################################################################
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
############################################################################
[6.] A small shell script or example program which triggers the
problem (if possible)
############################################################################
[7.] Environment
############################################################################
[7.1.] Software (add the output of the ver_linux script here)
############################################################################
[7.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 3
cpu MHz : 859.113
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov
pat pse36 mmx fxsr sse
bogomips : 1710.48
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 3
cpu MHz : 859.113
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 3
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov
pat pse36 mmx fxsr sse
bogomips : 1717.04
############################################################################
[7.3.] Module information (from /proc/modules):
evdev 3712 0 (unused)
mousedev 4288 0 (unused)
wacom 3344 0 (unused)
input 3680 0 [evdev mousedev wacom]
usb-uhci 23248 0 (unused)
usbcore 53776 2 [wacom usb-uhci]
############################################################################
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(auto)
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
4000-40ff : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
6000-607f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
9000-900f : VIA Technologies, Inc. Bus Master IDE
9400-941f : VIA Technologies, Inc. UHCI USB
9400-941f : usb-uhci
9800-981f : VIA Technologies, Inc. UHCI USB (#2)
9800-981f : usb-uhci
9c00-9cff : VIA Technologies, Inc. AC97 Audio Controller
a000-a003 : VIA Technologies, Inc. AC97 Audio Controller
a400-a403 : VIA Technologies, Inc. AC97 Audio Controller
ac00-ac07 : Promise Technology, Inc. 20265
b000-b003 : Promise Technology, Inc. 20265
b400-b407 : Promise Technology, Inc. 20265
b800-b803 : Promise Technology, Inc. 20265
bc00-bc3f : Promise Technology, Inc. 20265
c000-c0ff : Realtek Semiconductor Co., Ltd. RTL-8139
c000-c0ff : eth0
############################################################################
[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: VIA Technologies, Inc. VT82C691 [Apollo PRO] (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev 22)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 10) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at 9000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at 9400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at 9800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 [Apollo Super AC97/Audio] (rev 20)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super AC97/Audio]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at 9c00 [size=256]
Region 1: I/O ports at a000 [size=4]
Region 2: I/O ports at a400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 RAID bus controller: Promise Technology, Inc.: Unknown device 0d30 (rev 02)
Subsystem: Promise Technology, Inc.: Unknown device 4d39
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at ac00 [size=8]
Region 1: I/O ports at b000 [size=4]
Region 2: I/O ports at b400 [size=8]
Region 3: I/O ports at b800 [size=4]
Region 4: I/O ports at bc00 [size=64]
Region 5: Memory at df000000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8020 (prog-if 10 [OHCI])
Subsystem: Texas Instruments: Unknown device 8020
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 19
Region 0: Memory at df024000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at df020000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at c000 [size=256]
Region 1: Memory at df025000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation GeForce 256 (rev 10) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
############################################################################
[7.6.] SCSI information (from /proc/scsi/scsi)
############################################################################
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
Kernel with SMP /proc/bus/usb/devices:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 3 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=9800
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=9400
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
Kernel with ACPI (without SMP):
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 3 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=9800
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=9400
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
Kernel without SMP and ACPI:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 3 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=9800
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB UHCI Root Hub
S: SerialNumber=9400
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=056a ProdID=0010 Rev= 1.20
S: Manufacturer=WACOM
S: Product=ET-0405-UV1.2-0
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 40mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=wacom
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl= 10ms
############################################################################
[X.] Other notes, patches, fixes, workarounds:
On Sun, Mar 11, 2001 at 06:06:24PM +0100, Martin Bruchanov wrote:
>
> Bug report from Martin Bruchanov ([email protected], [email protected])
>
> ############################################################################
> [1.] One line summary of the problem:
> USB doesn't work properly with SMP kernel on dual-mainboard or with APIC.
What kind of motherboard is this?
And does USB work in SMP mode with "noapic" given on the kernel command
line?
thanks,
greg k-h
--
greg@(kroah|wirex).com
http://immunix.org/~greg
On Sun, Mar 11, 2001 at 09:03:09PM -0800, Greg KH wrote:
> On Sun, Mar 11, 2001 at 06:06:24PM +0100, Martin Bruchanov wrote:
> >
> > Bug report from Martin Bruchanov ([email protected], [email protected])
> >
> > ############################################################################
> > [1.] One line summary of the problem:
> > USB doesn't work properly with SMP kernel on dual-mainboard or with APIC.
>
> What kind of motherboard is this?
>
>From the lspci output, looks like I have the same mainboard or at
least one with an identical chipset. I've got an MSI 694D Pro
Mainboard with 694X VIA chipset, with 2 cpus installed, and I had the
same USB problem with 2.4.0, but haven't had time to test it on a
recent kernel.
robert
> And does USB work in SMP mode with "noapic" given on the kernel command
> line?
>
> thanks,
>
> greg k-h
>
> --
> greg@(kroah|wirex).com
> http://immunix.org/~greg
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/