Hi,
I get the following message at boot:
Linux version 2.5.42 (root@dreamland) (gcc version 3.2) #2 Sat Oct 12 21:39:57 CEST 2002
Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages
Normal zone: 61424 pages
HighMem zone: 0 pages
ACPI: RSDP (v000 VIA694 ) @ 0x000f7550
ACPI: RSDT (v001 VIA694 AWRDACPI 16944.11825) @ 0x0fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 16944.11825) @ 0x0fff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 00000.04096) @ 0x00000000
ACPI: Vendor "VIA694" System "AWRDACPI" Revision 0x0 has a known ACPI BIOS problem.
ACPI: Reason: Bogus table. This is a non-recoverable error
Then, at IDE init:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
PCI: No IRQ known for interrupt pin A of device 00:11.1. Please try using pci=biosirq.
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
Rebooting using pci=biosirq as requested:
Linux version 2.5.42 (root@dreamland) (gcc version 3.2) #2 Sat Oct 12 21:39:57 CEST 2002
Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages
Normal zone: 61424 pages
HighMem zone: 0 pages
ACPI: RSDP (v000 VIA694 ) @ 0x000f7550
ACPI: RSDT (v001 VIA694 AWRDACPI 16944.11825) @ 0x0fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 16944.11825) @ 0x0fff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 00000.04096) @ 0x00000000
ACPI: Vendor "VIA694" System "AWRDACPI" Revision 0x0 has a known ACPI BIOS problem.
ACPI: Reason: Bogus table. This is a non-recoverable error
[cut]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
PCI: No IRQ known for interrupt pin A of device 00:11.1.
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
lspci -vvv shows this:
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586 IDE [Apollo]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at e000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
"pin A routed to IRQ 0" seems a bit strange... but everything is
working. Btw, I've been running 2.4.41 with ACPI and it's rock solid.
This is the log:
ACPI: RSDP (v000 VIA694 ) @ 0x000f7550
ACPI: RSDT (v001 VIA694 AWRDACPI 16944.11825) @ 0x0fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 16944.11825) @ 0x0fff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
[cut]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
lspci -vvv:
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586 IDE [Apollo]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at e000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Another strangeness: when I reboot the machine (shutdown -r) my HD is
powered off: I can hear it spinning down when the screen goes blank and
spinning up when BIOS probes IDE channels.
kronos:/usr/src/linux-2.5$ grep ACPI .config | grep -v \#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_DEBUG=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_BUS=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
# CONFIG_SMP is not set
CONFIG_PREEMPT=y
The motherboard is an Epox8K3A (via kt333) with the latest bios.
HTH,
Luca
--
Reply-To: [email protected]
Home: http://kronoz.cjb.net
This message will self distruct in 5 seconds.