This patch set add imx7d adc driver support.
Changes in v5:
-call imx7d_adc_power_down() in driver probe when iio_device_register() failed
-handle with adc channel conversion timeout in imx7d_adc_isr()
Changes in v4:
-sort the include head file alphabetically
-really just clear the bit 31 of register REG_ADC_CH_A\B\C\D_CFG1
in function imx7d_adc_sample_rate_set()
-add document in imx7d_adc_isr() to clarify the clear operation
-add function imx7d_adc_power_down()
-adjust the format of the code and add some small changes
Changes in v3:
-move down the irq request in probe()
-remove the property 'num-channels' in dts
-remove some unused head file
-add clear register operation in imx7d_adc_isr()
Changes in v2:
-prefix defines with IMX7D_ for all the register
-use BIT macro to define a single bit
-remove the dma_en from struct adc_feature which is not support currently
-use static const array to replace the switch case code
Haibo Chen (4):
iio: adc: add IMX7D ADC driver support
Documentation: add the binding file for Freescale imx7d ADC driver
ARM: dts: imx7d.dtsi: add ADC support
ARM: dts: imx7d-sdb: add ADC support
.../devicetree/bindings/iio/adc/imx7d-adc.txt | 22 +
arch/arm/boot/dts/imx7d-sdb.dts | 10 +
arch/arm/boot/dts/imx7d.dtsi | 18 +
drivers/iio/adc/Kconfig | 9 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/imx7d_adc.c | 589 +++++++++++++++++++++
6 files changed, 649 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt
create mode 100644 drivers/iio/adc/imx7d_adc.c
--
1.9.1
Freescale i.MX7D soc contains a new ADC IP. This patch add this ADC
driver support, and the driver only support ADC software trigger.
Signed-off-by: Haibo Chen <[email protected]>
---
drivers/iio/adc/Kconfig | 9 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/imx7d_adc.c | 589 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 599 insertions(+)
create mode 100644 drivers/iio/adc/imx7d_adc.c
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 7868c74..3493a46 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -194,6 +194,15 @@ config HI8435
This driver can also be built as a module. If so, the module will be
called hi8435.
+config IMX7D_ADC
+ tristate "IMX7D ADC driver"
+ depends on ARCH_MXC || COMPILE_TEST
+ help
+ Say yes here to build support for IMX7D ADC.
+
+ This driver can also be built as a module. If so, the module will be
+ called imx7d_adc.
+
config LP8788_ADC
tristate "LP8788 ADC driver"
depends on MFD_LP8788
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 99b37a9..282ffc01 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
obj-$(CONFIG_HI8435) += hi8435.o
+obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
obj-$(CONFIG_MAX1027) += max1027.o
obj-$(CONFIG_MAX1363) += max1363.o
diff --git a/drivers/iio/adc/imx7d_adc.c b/drivers/iio/adc/imx7d_adc.c
new file mode 100644
index 0000000..d3511b9
--- /dev/null
+++ b/drivers/iio/adc/imx7d_adc.c
@@ -0,0 +1,589 @@
+/*
+ * Freescale i.MX7D ADC driver
+ *
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/driver.h>
+#include <linux/iio/sysfs.h>
+
+/* ADC register */
+#define IMX7D_REG_ADC_CH_A_CFG1 0x00
+#define IMX7D_REG_ADC_CH_A_CFG2 0x10
+#define IMX7D_REG_ADC_CH_B_CFG1 0x20
+#define IMX7D_REG_ADC_CH_B_CFG2 0x30
+#define IMX7D_REG_ADC_CH_C_CFG1 0x40
+#define IMX7D_REG_ADC_CH_C_CFG2 0x50
+#define IMX7D_REG_ADC_CH_D_CFG1 0x60
+#define IMX7D_REG_ADC_CH_D_CFG2 0x70
+#define IMX7D_REG_ADC_CH_SW_CFG 0x80
+#define IMX7D_REG_ADC_TIMER_UNIT 0x90
+#define IMX7D_REG_ADC_DMA_FIFO 0xa0
+#define IMX7D_REG_ADC_FIFO_STATUS 0xb0
+#define IMX7D_REG_ADC_INT_SIG_EN 0xc0
+#define IMX7D_REG_ADC_INT_EN 0xd0
+#define IMX7D_REG_ADC_INT_STATUS 0xe0
+#define IMX7D_REG_ADC_CHA_B_CNV_RSLT 0xf0
+#define IMX7D_REG_ADC_CHC_D_CNV_RSLT 0x100
+#define IMX7D_REG_ADC_CH_SW_CNV_RSLT 0x110
+#define IMX7D_REG_ADC_DMA_FIFO_DAT 0x120
+#define IMX7D_REG_ADC_ADC_CFG 0x130
+
+#define IMX7D_REG_ADC_CHANNEL_CFG2_BASE 0x10
+#define IMX7D_EACH_CHANNEL_REG_OFFSET 0x20
+
+#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_EN (0x1 << 31)
+#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_SINGLE BIT(30)
+#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_AVG_EN BIT(29)
+#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_SEL(x) ((x) << 24)
+
+#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_4 (0x0 << 12)
+#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_8 (0x1 << 12)
+#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_16 (0x2 << 12)
+#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_32 (0x3 << 12)
+
+#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_4 (0x0 << 29)
+#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_8 (0x1 << 29)
+#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_16 (0x2 << 29)
+#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_32 (0x3 << 29)
+#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_64 (0x4 << 29)
+#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_128 (0x5 << 29)
+
+#define IMX7D_REG_ADC_ADC_CFG_ADC_CLK_DOWN BIT(31)
+#define IMX7D_REG_ADC_ADC_CFG_ADC_POWER_DOWN BIT(1)
+#define IMX7D_REG_ADC_ADC_CFG_ADC_EN BIT(0)
+
+#define IMX7D_REG_ADC_INT_CHA_COV_INT_EN BIT(8)
+#define IMX7D_REG_ADC_INT_CHB_COV_INT_EN BIT(9)
+#define IMX7D_REG_ADC_INT_CHC_COV_INT_EN BIT(10)
+#define IMX7D_REG_ADC_INT_CHD_COV_INT_EN BIT(11)
+#define IMX7D_REG_ADC_INT_CHANNEL_INT_EN (IMX7D_REG_ADC_INT_CHA_COV_INT_EN | \
+ IMX7D_REG_ADC_INT_CHB_COV_INT_EN | \
+ IMX7D_REG_ADC_INT_CHC_COV_INT_EN | \
+ IMX7D_REG_ADC_INT_CHD_COV_INT_EN)
+#define IMX7D_REG_ADC_INT_STATUS_CHANNEL_INT_STATUS 0xf00
+#define IMX7D_REG_ADC_INT_STATUS_CHANNEL_CONV_TIME_OUT 0xf0000
+
+#define IMX7D_ADC_TIMEOUT msecs_to_jiffies(100)
+
+enum imx7d_adc_clk_pre_div {
+ IMX7D_ADC_ANALOG_CLK_PRE_DIV_4,
+ IMX7D_ADC_ANALOG_CLK_PRE_DIV_8,
+ IMX7D_ADC_ANALOG_CLK_PRE_DIV_16,
+ IMX7D_ADC_ANALOG_CLK_PRE_DIV_32,
+ IMX7D_ADC_ANALOG_CLK_PRE_DIV_64,
+ IMX7D_ADC_ANALOG_CLK_PRE_DIV_128,
+};
+
+enum imx7d_adc_average_num {
+ IMX7D_ADC_AVERAGE_NUM_4,
+ IMX7D_ADC_AVERAGE_NUM_8,
+ IMX7D_ADC_AVERAGE_NUM_16,
+ IMX7D_ADC_AVERAGE_NUM_32,
+};
+
+struct imx7d_adc_feature {
+ enum imx7d_adc_clk_pre_div clk_pre_div;
+ enum imx7d_adc_average_num avg_num;
+
+ u32 core_time_unit; /* impact the sample rate */
+
+ bool average_en;
+};
+
+struct imx7d_adc {
+ struct device *dev;
+ void __iomem *regs;
+ struct clk *clk;
+
+ u32 vref_uv;
+ u32 value;
+ u32 channel;
+ u32 pre_div_num;
+
+ struct regulator *vref;
+ struct imx7d_adc_feature adc_feature;
+
+ struct completion completion;
+};
+
+struct imx7d_adc_analogue_core_clk {
+ u32 pre_div;
+ u32 reg_config;
+};
+
+#define IMX7D_ADC_ANALOGUE_CLK_CONFIG(_pre_div, _reg_conf) { \
+ .pre_div = (_pre_div), \
+ .reg_config = (_reg_conf), \
+}
+
+static const struct imx7d_adc_analogue_core_clk imx7d_adc_analogue_clk[] = {
+ IMX7D_ADC_ANALOGUE_CLK_CONFIG(4, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_4),
+ IMX7D_ADC_ANALOGUE_CLK_CONFIG(8, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_8),
+ IMX7D_ADC_ANALOGUE_CLK_CONFIG(16, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_16),
+ IMX7D_ADC_ANALOGUE_CLK_CONFIG(32, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_32),
+ IMX7D_ADC_ANALOGUE_CLK_CONFIG(64, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_64),
+ IMX7D_ADC_ANALOGUE_CLK_CONFIG(128, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_128),
+};
+
+#define IMX7D_ADC_CHAN(_idx) { \
+ .type = IIO_VOLTAGE, \
+ .indexed = 1, \
+ .channel = (_idx), \
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \
+ BIT(IIO_CHAN_INFO_SAMP_FREQ), \
+}
+
+static const struct iio_chan_spec imx7d_adc_iio_channels[] = {
+ IMX7D_ADC_CHAN(0),
+ IMX7D_ADC_CHAN(1),
+ IMX7D_ADC_CHAN(2),
+ IMX7D_ADC_CHAN(3),
+ IMX7D_ADC_CHAN(4),
+ IMX7D_ADC_CHAN(5),
+ IMX7D_ADC_CHAN(6),
+ IMX7D_ADC_CHAN(7),
+ IMX7D_ADC_CHAN(8),
+ IMX7D_ADC_CHAN(9),
+ IMX7D_ADC_CHAN(10),
+ IMX7D_ADC_CHAN(11),
+ IMX7D_ADC_CHAN(12),
+ IMX7D_ADC_CHAN(13),
+ IMX7D_ADC_CHAN(14),
+ IMX7D_ADC_CHAN(15),
+};
+
+static const u32 imx7d_adc_average_num[] = {
+ IMX7D_REG_ADC_CH_CFG2_AVG_NUM_4,
+ IMX7D_REG_ADC_CH_CFG2_AVG_NUM_8,
+ IMX7D_REG_ADC_CH_CFG2_AVG_NUM_16,
+ IMX7D_REG_ADC_CH_CFG2_AVG_NUM_32,
+};
+
+static void imx7d_adc_feature_config(struct imx7d_adc *info)
+{
+ info->adc_feature.clk_pre_div = IMX7D_ADC_ANALOG_CLK_PRE_DIV_4;
+ info->adc_feature.avg_num = IMX7D_ADC_AVERAGE_NUM_32;
+ info->adc_feature.core_time_unit = 1;
+ info->adc_feature.average_en = true;
+}
+
+static void imx7d_adc_sample_rate_set(struct imx7d_adc *info)
+{
+ struct imx7d_adc_feature *adc_feature = &info->adc_feature;
+ struct imx7d_adc_analogue_core_clk adc_analogure_clk;
+ u32 i;
+ u32 tmp_cfg1;
+ u32 sample_rate = 0;
+
+ /*
+ * Before sample set, disable channel A,B,C,D. Here we
+ * clear the bit 31 of register REG_ADC_CH_A\B\C\D_CFG1.
+ */
+ for (i = 0; i < 4; i++) {
+ tmp_cfg1 = readl(info->regs + i * IMX7D_EACH_CHANNEL_REG_OFFSET);
+ tmp_cfg1 &= ~IMX7D_REG_ADC_CH_CFG1_CHANNEL_EN;
+ writel(tmp_cfg1, info->regs + i * IMX7D_EACH_CHANNEL_REG_OFFSET);
+ }
+
+ adc_analogure_clk = imx7d_adc_analogue_clk[adc_feature->clk_pre_div];
+ sample_rate |= adc_analogure_clk.reg_config;
+ info->pre_div_num = adc_analogure_clk.pre_div;
+
+ sample_rate |= adc_feature->core_time_unit;
+ writel(sample_rate, info->regs + IMX7D_REG_ADC_TIMER_UNIT);
+}
+
+static void imx7d_adc_hw_init(struct imx7d_adc *info)
+{
+ u32 cfg;
+
+ /* power up and enable adc analogue core */
+ cfg = readl(info->regs + IMX7D_REG_ADC_ADC_CFG);
+ cfg &= ~(IMX7D_REG_ADC_ADC_CFG_ADC_CLK_DOWN | IMX7D_REG_ADC_ADC_CFG_ADC_POWER_DOWN);
+ cfg |= IMX7D_REG_ADC_ADC_CFG_ADC_EN;
+ writel(cfg, info->regs + IMX7D_REG_ADC_ADC_CFG);
+
+ /* enable channel A,B,C,D interrupt */
+ writel(IMX7D_REG_ADC_INT_CHANNEL_INT_EN, info->regs + IMX7D_REG_ADC_INT_SIG_EN);
+ writel(IMX7D_REG_ADC_INT_CHANNEL_INT_EN, info->regs + IMX7D_REG_ADC_INT_EN);
+
+ imx7d_adc_sample_rate_set(info);
+}
+
+static void imx7d_adc_channel_set(struct imx7d_adc *info)
+{
+ u32 cfg1 = 0;
+ u32 cfg2;
+ u32 channel;
+
+ channel = info->channel;
+
+ /* the channel choose single conversion, and enable average mode */
+ cfg1 |= (IMX7D_REG_ADC_CH_CFG1_CHANNEL_EN |
+ IMX7D_REG_ADC_CH_CFG1_CHANNEL_SINGLE);
+ if (info->adc_feature.average_en)
+ cfg1 |= IMX7D_REG_ADC_CH_CFG1_CHANNEL_AVG_EN;
+
+ /*
+ * physical channel 0 chose logical channel A
+ * physical channel 1 chose logical channel B
+ * physical channel 2 chose logical channel C
+ * physical channel 3 chose logical channel D
+ */
+ cfg1 |= IMX7D_REG_ADC_CH_CFG1_CHANNEL_SEL(channel);
+
+ /* read register REG_ADC_CH_A\B\C\D_CFG2, according to the channel chosen */
+ cfg2 = readl(info->regs + IMX7D_EACH_CHANNEL_REG_OFFSET * channel + IMX7D_REG_ADC_CHANNEL_CFG2_BASE);
+
+ cfg2 |= imx7d_adc_average_num[info->adc_feature.avg_num];
+
+ /* write the register REG_ADC_CH_A\B\C\D_CFG2, according to the channel chosen */
+ writel(cfg2, info->regs + IMX7D_EACH_CHANNEL_REG_OFFSET * channel + IMX7D_REG_ADC_CHANNEL_CFG2_BASE);
+ writel(cfg1, info->regs + IMX7D_EACH_CHANNEL_REG_OFFSET * channel);
+}
+
+static u32 imx7d_adc_get_sample_rate(struct imx7d_adc *info)
+{
+ /* input clock is always 24MHz */
+ u32 input_clk = 24000000;
+ u32 analogue_core_clk;
+ u32 core_time_unit = info->adc_feature.core_time_unit;
+ u32 tmp;
+
+ analogue_core_clk = input_clk / info->pre_div_num;
+ tmp = (core_time_unit + 1) * 6;
+
+ return analogue_core_clk / tmp;
+}
+
+static int imx7d_adc_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val,
+ int *val2,
+ long mask)
+{
+ struct imx7d_adc *info = iio_priv(indio_dev);
+
+ u32 channel;
+ long ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ mutex_lock(&indio_dev->mlock);
+ reinit_completion(&info->completion);
+
+ channel = chan->channel & 0x03;
+ info->channel = channel;
+ imx7d_adc_channel_set(info);
+
+ ret = wait_for_completion_interruptible_timeout
+ (&info->completion, IMX7D_ADC_TIMEOUT);
+ if (ret == 0) {
+ mutex_unlock(&indio_dev->mlock);
+ return -ETIMEDOUT;
+ }
+ if (ret < 0) {
+ mutex_unlock(&indio_dev->mlock);
+ return ret;
+ }
+
+ *val = info->value;
+ mutex_unlock(&indio_dev->mlock);
+ return IIO_VAL_INT;
+
+ case IIO_CHAN_INFO_SCALE:
+ info->vref_uv = regulator_get_voltage(info->vref);
+ *val = info->vref_uv / 1000;
+ *val2 = 12;
+ return IIO_VAL_FRACTIONAL_LOG2;
+
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ *val = imx7d_adc_get_sample_rate(info);
+ return IIO_VAL_INT;
+
+ default:
+ return -EINVAL;
+ }
+}
+
+static int imx7d_adc_read_data(struct imx7d_adc *info)
+{
+ u32 channel;
+ u32 value;
+
+ channel = info->channel & 0x03;
+
+ /*
+ * channel A and B conversion result share one register,
+ * bit[27~16] is the channel B conversion result,
+ * bit[11~0] is the channel A conversion result.
+ * channel C and D is the same.
+ */
+ if (channel < 2)
+ value = readl(info->regs + IMX7D_REG_ADC_CHA_B_CNV_RSLT);
+ else
+ value = readl(info->regs + IMX7D_REG_ADC_CHC_D_CNV_RSLT);
+ if (channel & 0x1) /* channel B or D */
+ value = (value >> 16) & 0xFFF;
+ else /* channel A or C */
+ value &= 0xFFF;
+
+ return value;
+}
+
+static irqreturn_t imx7d_adc_isr(int irq, void *dev_id)
+{
+ struct imx7d_adc *info = (struct imx7d_adc *)dev_id;
+ int status;
+
+ status = readl(info->regs + IMX7D_REG_ADC_INT_STATUS);
+ if (status & IMX7D_REG_ADC_INT_STATUS_CHANNEL_INT_STATUS) {
+ info->value = imx7d_adc_read_data(info);
+ complete(&info->completion);
+
+ /*
+ * The register IMX7D_REG_ADC_INT_STATUS can't clear
+ * itself after read operation, need software to write
+ * 0 to the related bit. Here we clear the channel A/B/C/D
+ * conversion finished flag.
+ */
+ status &= ~IMX7D_REG_ADC_INT_STATUS_CHANNEL_INT_STATUS;
+ writel(status, info->regs + IMX7D_REG_ADC_INT_STATUS);
+ }
+
+ /*
+ * If the channel A/B/C/D conversion timeout, report it and clear these
+ * timeout flags.
+ */
+ if (status & IMX7D_REG_ADC_INT_STATUS_CHANNEL_CONV_TIME_OUT) {
+ pr_err("%s: ADC got conversion time out interrupt: 0x%08x\n",
+ dev_name(info->dev), status);
+ status &= ~IMX7D_REG_ADC_INT_STATUS_CHANNEL_CONV_TIME_OUT;
+ writel(status, info->regs + IMX7D_REG_ADC_INT_STATUS);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int imx7d_adc_reg_access(struct iio_dev *indio_dev,
+ unsigned reg, unsigned writeval,
+ unsigned *readval)
+{
+ struct imx7d_adc *info = iio_priv(indio_dev);
+
+ if (!readval || reg % 4 || reg > IMX7D_REG_ADC_ADC_CFG)
+ return -EINVAL;
+
+ *readval = readl(info->regs + reg);
+
+ return 0;
+}
+
+static const struct iio_info imx7d_adc_iio_info = {
+ .driver_module = THIS_MODULE,
+ .read_raw = &imx7d_adc_read_raw,
+ .debugfs_reg_access = &imx7d_adc_reg_access,
+};
+
+static const struct of_device_id imx7d_adc_match[] = {
+ { .compatible = "fsl,imx7d-adc", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx7d_adc_match);
+
+static void imx7d_adc_power_down(struct imx7d_adc *info)
+{
+ u32 adc_cfg;
+
+ adc_cfg = readl(info->regs + IMX7D_REG_ADC_ADC_CFG);
+ adc_cfg |= IMX7D_REG_ADC_ADC_CFG_ADC_CLK_DOWN |
+ IMX7D_REG_ADC_ADC_CFG_ADC_POWER_DOWN;
+ adc_cfg &= ~IMX7D_REG_ADC_ADC_CFG_ADC_EN;
+ writel(adc_cfg, info->regs + IMX7D_REG_ADC_ADC_CFG);
+}
+
+static int imx7d_adc_probe(struct platform_device *pdev)
+{
+ struct imx7d_adc *info;
+ struct iio_dev *indio_dev;
+ struct resource *mem;
+ int irq;
+ int ret;
+
+ indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*info));
+ if (!indio_dev) {
+ dev_err(&pdev->dev, "Failed allocating iio device\n");
+ return -ENOMEM;
+ }
+
+ info = iio_priv(indio_dev);
+ info->dev = &pdev->dev;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ info->regs = devm_ioremap_resource(&pdev->dev, mem);
+ if (IS_ERR(info->regs)) {
+ ret = PTR_ERR(info->regs);
+ dev_err(&pdev->dev, "Failed to remap adc memory, err = %d\n", ret);
+ return ret;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "No irq resource?\n");
+ return irq;
+ }
+
+ info->clk = devm_clk_get(&pdev->dev, "adc");
+ if (IS_ERR(info->clk)) {
+ ret = PTR_ERR(info->clk);
+ dev_err(&pdev->dev, "Failed getting clock, err = %d\n", ret);
+ return ret;
+ }
+
+ info->vref = devm_regulator_get(&pdev->dev, "vref");
+ if (IS_ERR(info->vref)) {
+ ret = PTR_ERR(info->vref);
+ dev_err(&pdev->dev, "Failed getting reference voltage, err = %d\n", ret);
+ return ret;
+ }
+
+ ret = regulator_enable(info->vref);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't enable adc reference top voltage, err = %d\n", ret);
+ return ret;
+ }
+
+ platform_set_drvdata(pdev, indio_dev);
+
+ init_completion(&info->completion);
+
+ indio_dev->name = dev_name(&pdev->dev);
+ indio_dev->dev.parent = &pdev->dev;
+ indio_dev->info = &imx7d_adc_iio_info;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->channels = imx7d_adc_iio_channels;
+ indio_dev->num_channels = ARRAY_SIZE(imx7d_adc_iio_channels);
+
+ ret = clk_prepare_enable(info->clk);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "Could not prepare or enable the clock.\n");
+ goto error_adc_clk_enable;
+ }
+
+ ret = devm_request_irq(info->dev, irq,
+ imx7d_adc_isr, 0,
+ dev_name(&pdev->dev), info);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed requesting irq, irq = %d\n", irq);
+ goto error_iio_device_register;
+ }
+
+ imx7d_adc_feature_config(info);
+ imx7d_adc_hw_init(info);
+
+ ret = iio_device_register(indio_dev);
+ if (ret) {
+ imx7d_adc_power_down(info);
+ dev_err(&pdev->dev, "Couldn't register the device.\n");
+ goto error_iio_device_register;
+ }
+
+ return 0;
+
+error_iio_device_register:
+ clk_disable_unprepare(info->clk);
+error_adc_clk_enable:
+ regulator_disable(info->vref);
+
+ return ret;
+}
+
+static int imx7d_adc_remove(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+ struct imx7d_adc *info = iio_priv(indio_dev);
+
+ imx7d_adc_power_down(info);
+
+ iio_device_unregister(indio_dev);
+ clk_disable_unprepare(info->clk);
+ regulator_disable(info->vref);
+
+ return 0;
+}
+
+static int __maybe_unused imx7d_adc_suspend(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct imx7d_adc *info = iio_priv(indio_dev);
+
+ imx7d_adc_power_down(info);
+
+ clk_disable_unprepare(info->clk);
+ regulator_disable(info->vref);
+
+ return 0;
+}
+
+static int __maybe_unused imx7d_adc_resume(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct imx7d_adc *info = iio_priv(indio_dev);
+ int ret;
+
+ ret = regulator_enable(info->vref);
+ if (ret) {
+ dev_err(info->dev,
+ "Can't enable adc reference top voltage, err = %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(info->clk);
+ if (ret) {
+ dev_err(info->dev,
+ "Could not prepare or enable clock.\n");
+ regulator_disable(info->vref);
+ return ret;
+ }
+
+ imx7d_adc_hw_init(info);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(imx7d_adc_pm_ops, imx7d_adc_suspend, imx7d_adc_resume);
+
+static struct platform_driver imx7d_adc_driver = {
+ .probe = imx7d_adc_probe,
+ .remove = imx7d_adc_remove,
+ .driver = {
+ .name = "imx7d_adc",
+ .of_match_table = imx7d_adc_match,
+ .pm = &imx7d_adc_pm_ops,
+ },
+};
+
+module_platform_driver(imx7d_adc_driver);
+
+MODULE_AUTHOR("Haibo Chen <[email protected]>");
+MODULE_DESCRIPTION("Freeacale IMX7D ADC driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
The patch adds the binding file for Freescale imx7d ADC driver.
Signed-off-by: Haibo Chen <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
.../devicetree/bindings/iio/adc/imx7d-adc.txt | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt
diff --git a/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt
new file mode 100644
index 0000000..5c184b9
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt
@@ -0,0 +1,22 @@
+Freescale imx7d ADC bindings
+
+The devicetree bindings are for the ADC driver written for
+imx7d SoC.
+
+Required properties:
+- compatible: Should be "fsl,imx7d-adc"
+- reg: Offset and length of the register set for the ADC device
+- interrupts: The interrupt number for the ADC device
+- clocks: The root clock of the ADC controller
+- clock-names: Must contain "adc", matching entry in the clocks property
+- vref-supply: The regulator supply ADC reference voltage
+
+Example:
+adc1: adc@30610000 {
+ compatible = "fsl,imx7d-adc";
+ reg = <0x30610000 0x10000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+ clock-names = "adc";
+ vref-supply = <®_vcc_3v3_mcu>;
+};
--
1.9.1
Add imx7d ADC support.
Signed-off-by: Haibo Chen <[email protected]>
---
arch/arm/boot/dts/imx7d.dtsi | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi
index ebc053a..aa0624d 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/imx7d.dtsi
@@ -583,6 +583,24 @@
reg = <0x30400000 0x400000>;
ranges;
+ adc1: adc@30610000 {
+ compatible = "fsl,imx7d-adc";
+ reg = <0x30610000 0x10000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+ clock-names = "adc";
+ status = "disabled";
+ };
+
+ adc2: adc@30620000 {
+ compatible = "fsl,imx7d-adc";
+ reg = <0x30620000 0x10000>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+ clock-names = "adc";
+ status = "disabled";
+ };
+
pwm1: pwm@30660000 {
compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
reg = <0x30660000 0x10000>;
--
1.9.1
Add ADC support for imx7d-sdb board.
Signed-off-by: Haibo Chen <[email protected]>
---
arch/arm/boot/dts/imx7d-sdb.dts | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 432aaf5..b2c4536 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -97,6 +97,16 @@
};
};
+&adc1 {
+ vref-supply = <®_vref_1v8>;
+ status = "okay";
+};
+
+&adc2 {
+ vref-supply = <®_vref_1v8>;
+ status = "okay";
+};
+
&cpu0 {
arm-supply = <&sw1a_reg>;
};
--
1.9.1
On 08/12/15 10:26, Haibo Chen wrote:
> The patch adds the binding file for Freescale imx7d ADC driver.
>
> Signed-off-by: Haibo Chen <[email protected]>
> Acked-by: Rob Herring <[email protected]>
Applied
> ---
> .../devicetree/bindings/iio/adc/imx7d-adc.txt | 22 ++++++++++++++++++++++
> 1 file changed, 22 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt
> new file mode 100644
> index 0000000..5c184b9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt
> @@ -0,0 +1,22 @@
> +Freescale imx7d ADC bindings
> +
> +The devicetree bindings are for the ADC driver written for
> +imx7d SoC.
> +
> +Required properties:
> +- compatible: Should be "fsl,imx7d-adc"
> +- reg: Offset and length of the register set for the ADC device
> +- interrupts: The interrupt number for the ADC device
> +- clocks: The root clock of the ADC controller
> +- clock-names: Must contain "adc", matching entry in the clocks property
> +- vref-supply: The regulator supply ADC reference voltage
> +
> +Example:
> +adc1: adc@30610000 {
> + compatible = "fsl,imx7d-adc";
> + reg = <0x30610000 0x10000>;
> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clks IMX7D_ADC_ROOT_CLK>;
> + clock-names = "adc";
> + vref-supply = <®_vcc_3v3_mcu>;
> +};
>
On 08/12/15 10:26, Haibo Chen wrote:
> Add imx7d ADC support.
>
> Signed-off-by: Haibo Chen <[email protected]>
The driver is now working its way in the direction of linux-next via
Greg KHs tree. I'm happy to take these changes as well, but would imagine
they are better routed through the relevant imx trees.
Jonathan
> ---
> arch/arm/boot/dts/imx7d.dtsi | 18 ++++++++++++++++++
> 1 file changed, 18 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi
> index ebc053a..aa0624d 100644
> --- a/arch/arm/boot/dts/imx7d.dtsi
> +++ b/arch/arm/boot/dts/imx7d.dtsi
> @@ -583,6 +583,24 @@
> reg = <0x30400000 0x400000>;
> ranges;
>
> + adc1: adc@30610000 {
> + compatible = "fsl,imx7d-adc";
> + reg = <0x30610000 0x10000>;
> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clks IMX7D_ADC_ROOT_CLK>;
> + clock-names = "adc";
> + status = "disabled";
> + };
> +
> + adc2: adc@30620000 {
> + compatible = "fsl,imx7d-adc";
> + reg = <0x30620000 0x10000>;
> + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clks IMX7D_ADC_ROOT_CLK>;
> + clock-names = "adc";
> + status = "disabled";
> + };
> +
> pwm1: pwm@30660000 {
> compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
> reg = <0x30660000 0x10000>;
>
On 08/12/15 10:26, Haibo Chen wrote:
> Freescale i.MX7D soc contains a new ADC IP. This patch add this ADC
> driver support, and the driver only support ADC software trigger.
>
> Signed-off-by: Haibo Chen <[email protected]>
One significant issue, but as the fix is simple I've made it.
A few formatting bits and bobs that I've also cleaned up (overly long lines).
If I don't clean them up on merge I have to deal with the little 'fix'
patches in the coming weeks :) Easier to do it now.
I left one case where I felt it would hurt readability alone, but fixed the
others.
Applied to the togreg branch of iio.git - initially pushed out as testing
for the autobuilders to play with it.
Thanks,
Jonathan
> ---
> drivers/iio/adc/Kconfig | 9 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/imx7d_adc.c | 589 ++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 599 insertions(+)
> create mode 100644 drivers/iio/adc/imx7d_adc.c
>
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 7868c74..3493a46 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -194,6 +194,15 @@ config HI8435
> This driver can also be built as a module. If so, the module will be
> called hi8435.
>
> +config IMX7D_ADC
> + tristate "IMX7D ADC driver"
> + depends on ARCH_MXC || COMPILE_TEST
> + help
> + Say yes here to build support for IMX7D ADC.
> +
> + This driver can also be built as a module. If so, the module will be
> + called imx7d_adc.
> +
> config LP8788_ADC
> tristate "LP8788 ADC driver"
> depends on MFD_LP8788
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 99b37a9..282ffc01 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -20,6 +20,7 @@ obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
> obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
> obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> obj-$(CONFIG_HI8435) += hi8435.o
> +obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
> obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
> obj-$(CONFIG_MAX1027) += max1027.o
> obj-$(CONFIG_MAX1363) += max1363.o
> diff --git a/drivers/iio/adc/imx7d_adc.c b/drivers/iio/adc/imx7d_adc.c
> new file mode 100644
> index 0000000..d3511b9
> --- /dev/null
> +++ b/drivers/iio/adc/imx7d_adc.c
> @@ -0,0 +1,589 @@
> +/*
> + * Freescale i.MX7D ADC driver
> + *
> + * Copyright (C) 2015 Freescale Semiconductor, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/completion.h>
> +#include <linux/err.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +
> +#include <linux/iio/iio.h>
> +#include <linux/iio/driver.h>
> +#include <linux/iio/sysfs.h>
> +
> +/* ADC register */
> +#define IMX7D_REG_ADC_CH_A_CFG1 0x00
> +#define IMX7D_REG_ADC_CH_A_CFG2 0x10
> +#define IMX7D_REG_ADC_CH_B_CFG1 0x20
> +#define IMX7D_REG_ADC_CH_B_CFG2 0x30
> +#define IMX7D_REG_ADC_CH_C_CFG1 0x40
> +#define IMX7D_REG_ADC_CH_C_CFG2 0x50
> +#define IMX7D_REG_ADC_CH_D_CFG1 0x60
> +#define IMX7D_REG_ADC_CH_D_CFG2 0x70
> +#define IMX7D_REG_ADC_CH_SW_CFG 0x80
> +#define IMX7D_REG_ADC_TIMER_UNIT 0x90
> +#define IMX7D_REG_ADC_DMA_FIFO 0xa0
> +#define IMX7D_REG_ADC_FIFO_STATUS 0xb0
> +#define IMX7D_REG_ADC_INT_SIG_EN 0xc0
> +#define IMX7D_REG_ADC_INT_EN 0xd0
> +#define IMX7D_REG_ADC_INT_STATUS 0xe0
> +#define IMX7D_REG_ADC_CHA_B_CNV_RSLT 0xf0
> +#define IMX7D_REG_ADC_CHC_D_CNV_RSLT 0x100
> +#define IMX7D_REG_ADC_CH_SW_CNV_RSLT 0x110
> +#define IMX7D_REG_ADC_DMA_FIFO_DAT 0x120
> +#define IMX7D_REG_ADC_ADC_CFG 0x130
> +
> +#define IMX7D_REG_ADC_CHANNEL_CFG2_BASE 0x10
> +#define IMX7D_EACH_CHANNEL_REG_OFFSET 0x20
> +
> +#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_EN (0x1 << 31)
> +#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_SINGLE BIT(30)
> +#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_AVG_EN BIT(29)
> +#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_SEL(x) ((x) << 24)
> +
> +#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_4 (0x0 << 12)
> +#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_8 (0x1 << 12)
> +#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_16 (0x2 << 12)
> +#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_32 (0x3 << 12)
> +
> +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_4 (0x0 << 29)
> +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_8 (0x1 << 29)
> +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_16 (0x2 << 29)
> +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_32 (0x3 << 29)
> +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_64 (0x4 << 29)
> +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_128 (0x5 << 29)
> +
> +#define IMX7D_REG_ADC_ADC_CFG_ADC_CLK_DOWN BIT(31)
> +#define IMX7D_REG_ADC_ADC_CFG_ADC_POWER_DOWN BIT(1)
> +#define IMX7D_REG_ADC_ADC_CFG_ADC_EN BIT(0)
> +
> +#define IMX7D_REG_ADC_INT_CHA_COV_INT_EN BIT(8)
> +#define IMX7D_REG_ADC_INT_CHB_COV_INT_EN BIT(9)
> +#define IMX7D_REG_ADC_INT_CHC_COV_INT_EN BIT(10)
> +#define IMX7D_REG_ADC_INT_CHD_COV_INT_EN BIT(11)
> +#define IMX7D_REG_ADC_INT_CHANNEL_INT_EN (IMX7D_REG_ADC_INT_CHA_COV_INT_EN | \
> + IMX7D_REG_ADC_INT_CHB_COV_INT_EN | \
> + IMX7D_REG_ADC_INT_CHC_COV_INT_EN | \
> + IMX7D_REG_ADC_INT_CHD_COV_INT_EN)
> +#define IMX7D_REG_ADC_INT_STATUS_CHANNEL_INT_STATUS 0xf00
> +#define IMX7D_REG_ADC_INT_STATUS_CHANNEL_CONV_TIME_OUT 0xf0000
> +
> +#define IMX7D_ADC_TIMEOUT msecs_to_jiffies(100)
> +
> +enum imx7d_adc_clk_pre_div {
> + IMX7D_ADC_ANALOG_CLK_PRE_DIV_4,
> + IMX7D_ADC_ANALOG_CLK_PRE_DIV_8,
> + IMX7D_ADC_ANALOG_CLK_PRE_DIV_16,
> + IMX7D_ADC_ANALOG_CLK_PRE_DIV_32,
> + IMX7D_ADC_ANALOG_CLK_PRE_DIV_64,
> + IMX7D_ADC_ANALOG_CLK_PRE_DIV_128,
> +};
> +
> +enum imx7d_adc_average_num {
> + IMX7D_ADC_AVERAGE_NUM_4,
> + IMX7D_ADC_AVERAGE_NUM_8,
> + IMX7D_ADC_AVERAGE_NUM_16,
> + IMX7D_ADC_AVERAGE_NUM_32,
> +};
> +
> +struct imx7d_adc_feature {
> + enum imx7d_adc_clk_pre_div clk_pre_div;
> + enum imx7d_adc_average_num avg_num;
> +
> + u32 core_time_unit; /* impact the sample rate */
> +
> + bool average_en;
> +};
> +
> +struct imx7d_adc {
> + struct device *dev;
> + void __iomem *regs;
> + struct clk *clk;
> +
> + u32 vref_uv;
> + u32 value;
> + u32 channel;
> + u32 pre_div_num;
> +
> + struct regulator *vref;
> + struct imx7d_adc_feature adc_feature;
> +
> + struct completion completion;
> +};
> +
> +struct imx7d_adc_analogue_core_clk {
> + u32 pre_div;
> + u32 reg_config;
> +};
> +
> +#define IMX7D_ADC_ANALOGUE_CLK_CONFIG(_pre_div, _reg_conf) { \
> + .pre_div = (_pre_div), \
> + .reg_config = (_reg_conf), \
> +}
> +
> +static const struct imx7d_adc_analogue_core_clk imx7d_adc_analogue_clk[] = {
> + IMX7D_ADC_ANALOGUE_CLK_CONFIG(4, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_4),
> + IMX7D_ADC_ANALOGUE_CLK_CONFIG(8, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_8),
> + IMX7D_ADC_ANALOGUE_CLK_CONFIG(16, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_16),
> + IMX7D_ADC_ANALOGUE_CLK_CONFIG(32, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_32),
> + IMX7D_ADC_ANALOGUE_CLK_CONFIG(64, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_64),
> + IMX7D_ADC_ANALOGUE_CLK_CONFIG(128, IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_128),
> +};
> +
> +#define IMX7D_ADC_CHAN(_idx) { \
> + .type = IIO_VOLTAGE, \
> + .indexed = 1, \
> + .channel = (_idx), \
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \
> + BIT(IIO_CHAN_INFO_SAMP_FREQ), \
> +}
> +
> +static const struct iio_chan_spec imx7d_adc_iio_channels[] = {
> + IMX7D_ADC_CHAN(0),
> + IMX7D_ADC_CHAN(1),
> + IMX7D_ADC_CHAN(2),
> + IMX7D_ADC_CHAN(3),
> + IMX7D_ADC_CHAN(4),
> + IMX7D_ADC_CHAN(5),
> + IMX7D_ADC_CHAN(6),
> + IMX7D_ADC_CHAN(7),
> + IMX7D_ADC_CHAN(8),
> + IMX7D_ADC_CHAN(9),
> + IMX7D_ADC_CHAN(10),
> + IMX7D_ADC_CHAN(11),
> + IMX7D_ADC_CHAN(12),
> + IMX7D_ADC_CHAN(13),
> + IMX7D_ADC_CHAN(14),
> + IMX7D_ADC_CHAN(15),
> +};
> +
> +static const u32 imx7d_adc_average_num[] = {
> + IMX7D_REG_ADC_CH_CFG2_AVG_NUM_4,
> + IMX7D_REG_ADC_CH_CFG2_AVG_NUM_8,
> + IMX7D_REG_ADC_CH_CFG2_AVG_NUM_16,
> + IMX7D_REG_ADC_CH_CFG2_AVG_NUM_32,
> +};
> +
> +static void imx7d_adc_feature_config(struct imx7d_adc *info)
> +{
> + info->adc_feature.clk_pre_div = IMX7D_ADC_ANALOG_CLK_PRE_DIV_4;
> + info->adc_feature.avg_num = IMX7D_ADC_AVERAGE_NUM_32;
> + info->adc_feature.core_time_unit = 1;
> + info->adc_feature.average_en = true;
> +}
> +
> +static void imx7d_adc_sample_rate_set(struct imx7d_adc *info)
> +{
> + struct imx7d_adc_feature *adc_feature = &info->adc_feature;
> + struct imx7d_adc_analogue_core_clk adc_analogure_clk;
> + u32 i;
> + u32 tmp_cfg1;
> + u32 sample_rate = 0;
> +
> + /*
> + * Before sample set, disable channel A,B,C,D. Here we
> + * clear the bit 31 of register REG_ADC_CH_A\B\C\D_CFG1.
> + */
> + for (i = 0; i < 4; i++) {
> + tmp_cfg1 = readl(info->regs + i * IMX7D_EACH_CHANNEL_REG_OFFSET);
> + tmp_cfg1 &= ~IMX7D_REG_ADC_CH_CFG1_CHANNEL_EN;
> + writel(tmp_cfg1, info->regs + i * IMX7D_EACH_CHANNEL_REG_OFFSET);
> + }
> +
> + adc_analogure_clk = imx7d_adc_analogue_clk[adc_feature->clk_pre_div];
> + sample_rate |= adc_analogure_clk.reg_config;
> + info->pre_div_num = adc_analogure_clk.pre_div;
> +
> + sample_rate |= adc_feature->core_time_unit;
> + writel(sample_rate, info->regs + IMX7D_REG_ADC_TIMER_UNIT);
> +}
> +
> +static void imx7d_adc_hw_init(struct imx7d_adc *info)
> +{
> + u32 cfg;
> +
> + /* power up and enable adc analogue core */
> + cfg = readl(info->regs + IMX7D_REG_ADC_ADC_CFG);
> + cfg &= ~(IMX7D_REG_ADC_ADC_CFG_ADC_CLK_DOWN | IMX7D_REG_ADC_ADC_CFG_ADC_POWER_DOWN);
> + cfg |= IMX7D_REG_ADC_ADC_CFG_ADC_EN;
> + writel(cfg, info->regs + IMX7D_REG_ADC_ADC_CFG);
> +
> + /* enable channel A,B,C,D interrupt */
> + writel(IMX7D_REG_ADC_INT_CHANNEL_INT_EN, info->regs + IMX7D_REG_ADC_INT_SIG_EN);
> + writel(IMX7D_REG_ADC_INT_CHANNEL_INT_EN, info->regs + IMX7D_REG_ADC_INT_EN);
> +
> + imx7d_adc_sample_rate_set(info);
> +}
> +
> +static void imx7d_adc_channel_set(struct imx7d_adc *info)
> +{
> + u32 cfg1 = 0;
> + u32 cfg2;
> + u32 channel;
> +
> + channel = info->channel;
> +
> + /* the channel choose single conversion, and enable average mode */
> + cfg1 |= (IMX7D_REG_ADC_CH_CFG1_CHANNEL_EN |
> + IMX7D_REG_ADC_CH_CFG1_CHANNEL_SINGLE);
> + if (info->adc_feature.average_en)
> + cfg1 |= IMX7D_REG_ADC_CH_CFG1_CHANNEL_AVG_EN;
> +
> + /*
> + * physical channel 0 chose logical channel A
> + * physical channel 1 chose logical channel B
> + * physical channel 2 chose logical channel C
> + * physical channel 3 chose logical channel D
> + */
> + cfg1 |= IMX7D_REG_ADC_CH_CFG1_CHANNEL_SEL(channel);
> +
> + /* read register REG_ADC_CH_A\B\C\D_CFG2, according to the channel chosen */
> + cfg2 = readl(info->regs + IMX7D_EACH_CHANNEL_REG_OFFSET * channel + IMX7D_REG_ADC_CHANNEL_CFG2_BASE);
> +
> + cfg2 |= imx7d_adc_average_num[info->adc_feature.avg_num];
> +
> + /* write the register REG_ADC_CH_A\B\C\D_CFG2, according to the channel chosen */
> + writel(cfg2, info->regs + IMX7D_EACH_CHANNEL_REG_OFFSET * channel + IMX7D_REG_ADC_CHANNEL_CFG2_BASE);
Whilst line length limits are not set in stone it is best to stick to them if
there is no good reason to not do so. Here it owuld make no real difference.
> + writel(cfg1, info->regs + IMX7D_EACH_CHANNEL_REG_OFFSET * channel);
> +}
> +
> +static u32 imx7d_adc_get_sample_rate(struct imx7d_adc *info)
> +{
> + /* input clock is always 24MHz */
> + u32 input_clk = 24000000;
> + u32 analogue_core_clk;
> + u32 core_time_unit = info->adc_feature.core_time_unit;
> + u32 tmp;
> +
> + analogue_core_clk = input_clk / info->pre_div_num;
> + tmp = (core_time_unit + 1) * 6;
> +
> + return analogue_core_clk / tmp;
> +}
> +
> +static int imx7d_adc_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val,
> + int *val2,
> + long mask)
> +{
> + struct imx7d_adc *info = iio_priv(indio_dev);
> +
> + u32 channel;
> + long ret;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + mutex_lock(&indio_dev->mlock);
> + reinit_completion(&info->completion);
> +
> + channel = chan->channel & 0x03;
> + info->channel = channel;
> + imx7d_adc_channel_set(info);
> +
> + ret = wait_for_completion_interruptible_timeout
> + (&info->completion, IMX7D_ADC_TIMEOUT);
> + if (ret == 0) {
> + mutex_unlock(&indio_dev->mlock);
> + return -ETIMEDOUT;
> + }
> + if (ret < 0) {
> + mutex_unlock(&indio_dev->mlock);
> + return ret;
> + }
> +
> + *val = info->value;
> + mutex_unlock(&indio_dev->mlock);
> + return IIO_VAL_INT;
> +
> + case IIO_CHAN_INFO_SCALE:
> + info->vref_uv = regulator_get_voltage(info->vref);
> + *val = info->vref_uv / 1000;
> + *val2 = 12;
> + return IIO_VAL_FRACTIONAL_LOG2;
> +
> + case IIO_CHAN_INFO_SAMP_FREQ:
> + *val = imx7d_adc_get_sample_rate(info);
> + return IIO_VAL_INT;
> +
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int imx7d_adc_read_data(struct imx7d_adc *info)
> +{
> + u32 channel;
> + u32 value;
> +
> + channel = info->channel & 0x03;
> +
> + /*
> + * channel A and B conversion result share one register,
> + * bit[27~16] is the channel B conversion result,
> + * bit[11~0] is the channel A conversion result.
> + * channel C and D is the same.
> + */
> + if (channel < 2)
> + value = readl(info->regs + IMX7D_REG_ADC_CHA_B_CNV_RSLT);
> + else
> + value = readl(info->regs + IMX7D_REG_ADC_CHC_D_CNV_RSLT);
> + if (channel & 0x1) /* channel B or D */
> + value = (value >> 16) & 0xFFF;
> + else /* channel A or C */
> + value &= 0xFFF;
> +
> + return value;
> +}
> +
> +static irqreturn_t imx7d_adc_isr(int irq, void *dev_id)
> +{
> + struct imx7d_adc *info = (struct imx7d_adc *)dev_id;
> + int status;
> +
> + status = readl(info->regs + IMX7D_REG_ADC_INT_STATUS);
> + if (status & IMX7D_REG_ADC_INT_STATUS_CHANNEL_INT_STATUS) {
> + info->value = imx7d_adc_read_data(info);
> + complete(&info->completion);
> +
> + /*
> + * The register IMX7D_REG_ADC_INT_STATUS can't clear
> + * itself after read operation, need software to write
> + * 0 to the related bit. Here we clear the channel A/B/C/D
> + * conversion finished flag.
> + */
> + status &= ~IMX7D_REG_ADC_INT_STATUS_CHANNEL_INT_STATUS;
> + writel(status, info->regs + IMX7D_REG_ADC_INT_STATUS);
> + }
> +
> + /*
> + * If the channel A/B/C/D conversion timeout, report it and clear these
> + * timeout flags.
> + */
> + if (status & IMX7D_REG_ADC_INT_STATUS_CHANNEL_CONV_TIME_OUT) {
> + pr_err("%s: ADC got conversion time out interrupt: 0x%08x\n",
> + dev_name(info->dev), status);
> + status &= ~IMX7D_REG_ADC_INT_STATUS_CHANNEL_CONV_TIME_OUT;
> + writel(status, info->regs + IMX7D_REG_ADC_INT_STATUS);
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int imx7d_adc_reg_access(struct iio_dev *indio_dev,
> + unsigned reg, unsigned writeval,
> + unsigned *readval)
> +{
> + struct imx7d_adc *info = iio_priv(indio_dev);
> +
> + if (!readval || reg % 4 || reg > IMX7D_REG_ADC_ADC_CFG)
> + return -EINVAL;
> +
> + *readval = readl(info->regs + reg);
> +
> + return 0;
> +}
> +
> +static const struct iio_info imx7d_adc_iio_info = {
> + .driver_module = THIS_MODULE,
> + .read_raw = &imx7d_adc_read_raw,
> + .debugfs_reg_access = &imx7d_adc_reg_access,
> +};
> +
> +static const struct of_device_id imx7d_adc_match[] = {
> + { .compatible = "fsl,imx7d-adc", },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, imx7d_adc_match);
> +
> +static void imx7d_adc_power_down(struct imx7d_adc *info)
> +{
> + u32 adc_cfg;
> +
> + adc_cfg = readl(info->regs + IMX7D_REG_ADC_ADC_CFG);
> + adc_cfg |= IMX7D_REG_ADC_ADC_CFG_ADC_CLK_DOWN |
> + IMX7D_REG_ADC_ADC_CFG_ADC_POWER_DOWN;
> + adc_cfg &= ~IMX7D_REG_ADC_ADC_CFG_ADC_EN;
> + writel(adc_cfg, info->regs + IMX7D_REG_ADC_ADC_CFG);
> +}
> +
> +static int imx7d_adc_probe(struct platform_device *pdev)
> +{
> + struct imx7d_adc *info;
> + struct iio_dev *indio_dev;
> + struct resource *mem;
> + int irq;
> + int ret;
> +
> + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*info));
> + if (!indio_dev) {
> + dev_err(&pdev->dev, "Failed allocating iio device\n");
> + return -ENOMEM;
> + }
> +
> + info = iio_priv(indio_dev);
> + info->dev = &pdev->dev;
> +
> + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + info->regs = devm_ioremap_resource(&pdev->dev, mem);
> + if (IS_ERR(info->regs)) {
> + ret = PTR_ERR(info->regs);
> + dev_err(&pdev->dev, "Failed to remap adc memory, err = %d\n", ret);
> + return ret;
> + }
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0) {
> + dev_err(&pdev->dev, "No irq resource?\n");
> + return irq;
> + }
> +
> + info->clk = devm_clk_get(&pdev->dev, "adc");
> + if (IS_ERR(info->clk)) {
> + ret = PTR_ERR(info->clk);
> + dev_err(&pdev->dev, "Failed getting clock, err = %d\n", ret);
> + return ret;
> + }
> +
> + info->vref = devm_regulator_get(&pdev->dev, "vref");
> + if (IS_ERR(info->vref)) {
> + ret = PTR_ERR(info->vref);
> + dev_err(&pdev->dev, "Failed getting reference voltage, err = %d\n", ret);
> + return ret;
> + }
> +
> + ret = regulator_enable(info->vref);
> + if (ret) {
> + dev_err(&pdev->dev, "Can't enable adc reference top voltage, err = %d\n", ret);
> + return ret;
> + }
> +
> + platform_set_drvdata(pdev, indio_dev);
> +
> + init_completion(&info->completion);
> +
> + indio_dev->name = dev_name(&pdev->dev);
> + indio_dev->dev.parent = &pdev->dev;
> + indio_dev->info = &imx7d_adc_iio_info;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->channels = imx7d_adc_iio_channels;
> + indio_dev->num_channels = ARRAY_SIZE(imx7d_adc_iio_channels);
> +
> + ret = clk_prepare_enable(info->clk);
> + if (ret) {
> + dev_err(&pdev->dev,
> + "Could not prepare or enable the clock.\n");
> + goto error_adc_clk_enable;
> + }
> +
> + ret = devm_request_irq(info->dev, irq,
> + imx7d_adc_isr, 0,
> + dev_name(&pdev->dev), info);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "Failed requesting irq, irq = %d\n", irq);
> + goto error_iio_device_register;
It's trivial but this goto label naming isn't accurate as the device register
doesn't occur for a few more lines...
> + }
> +
> + imx7d_adc_feature_config(info);
> + imx7d_adc_hw_init(info);
> +
> + ret = iio_device_register(indio_dev);
> + if (ret) {
> + imx7d_adc_power_down(info);
> + dev_err(&pdev->dev, "Couldn't register the device.\n");
> + goto error_iio_device_register;
> + }
> +
> + return 0;
> +
> +error_iio_device_register:
> + clk_disable_unprepare(info->clk);
> +error_adc_clk_enable:
> + regulator_disable(info->vref);
> +
> + return ret;
> +}
> +
> +static int imx7d_adc_remove(struct platform_device *pdev)
> +{
> + struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> + struct imx7d_adc *info = iio_priv(indio_dev);
> +
> + imx7d_adc_power_down(info);
I might fix this up, but the power down definitely wants to occur
'after' you have removed the userspace interface (so after the
iio_device_unregister call).
> +
> + iio_device_unregister(indio_dev);
> + clk_disable_unprepare(info->clk);
> + regulator_disable(info->vref);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused imx7d_adc_suspend(struct device *dev)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct imx7d_adc *info = iio_priv(indio_dev);
> +
> + imx7d_adc_power_down(info);
> +
> + clk_disable_unprepare(info->clk);
> + regulator_disable(info->vref);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused imx7d_adc_resume(struct device *dev)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct imx7d_adc *info = iio_priv(indio_dev);
> + int ret;
> +
> + ret = regulator_enable(info->vref);
> + if (ret) {
> + dev_err(info->dev,
> + "Can't enable adc reference top voltage, err = %d\n", ret);
> + return ret;
> + }
> +
> + ret = clk_prepare_enable(info->clk);
> + if (ret) {
> + dev_err(info->dev,
> + "Could not prepare or enable clock.\n");
> + regulator_disable(info->vref);
> + return ret;
> + }
> +
> + imx7d_adc_hw_init(info);
> +
> + return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(imx7d_adc_pm_ops, imx7d_adc_suspend, imx7d_adc_resume);
> +
> +static struct platform_driver imx7d_adc_driver = {
> + .probe = imx7d_adc_probe,
> + .remove = imx7d_adc_remove,
> + .driver = {
> + .name = "imx7d_adc",
> + .of_match_table = imx7d_adc_match,
> + .pm = &imx7d_adc_pm_ops,
> + },
> +};
> +
> +module_platform_driver(imx7d_adc_driver);
> +
> +MODULE_AUTHOR("Haibo Chen <[email protected]>");
> +MODULE_DESCRIPTION("Freeacale IMX7D ADC driver");
> +MODULE_LICENSE("GPL v2");
>
Hi Jonathan,
Thanks for your careful and patient review!
Best Regards
Haibo Chen
> -----Original Message-----
> From: Jonathan Cameron [mailto:[email protected]]
> Sent: Sunday, December 13, 2015 1:03 AM
> To: Chen Haibo-B51421; [email protected]; [email protected];
> [email protected]; [email protected]; [email protected]
> Cc: [email protected]; [email protected]; linux-arm-
> [email protected]; [email protected]
> Subject: Re: [PATCH v5 1/4] iio: adc: add IMX7D ADC driver support
>
> On 08/12/15 10:26, Haibo Chen wrote:
> > Freescale i.MX7D soc contains a new ADC IP. This patch add this ADC
> > driver support, and the driver only support ADC software trigger.
> >
> > Signed-off-by: Haibo Chen <[email protected]>
> One significant issue, but as the fix is simple I've made it.
> A few formatting bits and bobs that I've also cleaned up (overly long
> lines).
> If I don't clean them up on merge I have to deal with the little 'fix'
> patches in the coming weeks :) Easier to do it now.
> I left one case where I felt it would hurt readability alone, but fixed
> the others.
>
> Applied to the togreg branch of iio.git - initially pushed out as testing
> for the autobuilders to play with it.
>
> Thanks,
>
> Jonathan
> > ---
> > drivers/iio/adc/Kconfig | 9 +
> > drivers/iio/adc/Makefile | 1 +
> > drivers/iio/adc/imx7d_adc.c | 589
> > ++++++++++++++++++++++++++++++++++++++++++++
> > 3 files changed, 599 insertions(+)
> > create mode 100644 drivers/iio/adc/imx7d_adc.c
> >
> > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig index
> > 7868c74..3493a46 100644
> > --- a/drivers/iio/adc/Kconfig
> > +++ b/drivers/iio/adc/Kconfig
> > @@ -194,6 +194,15 @@ config HI8435
> > This driver can also be built as a module. If so, the module will
> be
> > called hi8435.
> >
> > +config IMX7D_ADC
> > + tristate "IMX7D ADC driver"
> > + depends on ARCH_MXC || COMPILE_TEST
> > + help
> > + Say yes here to build support for IMX7D ADC.
> > +
> > + This driver can also be built as a module. If so, the module will
> be
> > + called imx7d_adc.
> > +
> > config LP8788_ADC
> > tristate "LP8788 ADC driver"
> > depends on MFD_LP8788
> > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile index
> > 99b37a9..282ffc01 100644
> > --- a/drivers/iio/adc/Makefile
> > +++ b/drivers/iio/adc/Makefile
> > @@ -20,6 +20,7 @@ obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
> > obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
> > obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> > obj-$(CONFIG_HI8435) += hi8435.o
> > +obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
> > obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
> > obj-$(CONFIG_MAX1027) += max1027.o
> > obj-$(CONFIG_MAX1363) += max1363.o
> > diff --git a/drivers/iio/adc/imx7d_adc.c b/drivers/iio/adc/imx7d_adc.c
> > new file mode 100644 index 0000000..d3511b9
> > --- /dev/null
> > +++ b/drivers/iio/adc/imx7d_adc.c
> > @@ -0,0 +1,589 @@
> > +/*
> > + * Freescale i.MX7D ADC driver
> > + *
> > + * Copyright (C) 2015 Freescale Semiconductor, Inc.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > +modify
> > + * it under the terms of the GNU General Public License as published
> > +by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/completion.h>
> > +#include <linux/err.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/io.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regulator/consumer.h>
> > +
> > +#include <linux/iio/iio.h>
> > +#include <linux/iio/driver.h>
> > +#include <linux/iio/sysfs.h>
> > +
> > +/* ADC register */
> > +#define IMX7D_REG_ADC_CH_A_CFG1 0x00
> > +#define IMX7D_REG_ADC_CH_A_CFG2 0x10
> > +#define IMX7D_REG_ADC_CH_B_CFG1 0x20
> > +#define IMX7D_REG_ADC_CH_B_CFG2 0x30
> > +#define IMX7D_REG_ADC_CH_C_CFG1 0x40
> > +#define IMX7D_REG_ADC_CH_C_CFG2 0x50
> > +#define IMX7D_REG_ADC_CH_D_CFG1 0x60
> > +#define IMX7D_REG_ADC_CH_D_CFG2 0x70
> > +#define IMX7D_REG_ADC_CH_SW_CFG 0x80
> > +#define IMX7D_REG_ADC_TIMER_UNIT 0x90
> > +#define IMX7D_REG_ADC_DMA_FIFO 0xa0
> > +#define IMX7D_REG_ADC_FIFO_STATUS 0xb0
> > +#define IMX7D_REG_ADC_INT_SIG_EN 0xc0
> > +#define IMX7D_REG_ADC_INT_EN 0xd0
> > +#define IMX7D_REG_ADC_INT_STATUS 0xe0
> > +#define IMX7D_REG_ADC_CHA_B_CNV_RSLT 0xf0
> > +#define IMX7D_REG_ADC_CHC_D_CNV_RSLT 0x100
> > +#define IMX7D_REG_ADC_CH_SW_CNV_RSLT 0x110
> > +#define IMX7D_REG_ADC_DMA_FIFO_DAT 0x120
> > +#define IMX7D_REG_ADC_ADC_CFG 0x130
> > +
> > +#define IMX7D_REG_ADC_CHANNEL_CFG2_BASE 0x10
> > +#define IMX7D_EACH_CHANNEL_REG_OFFSET 0x20
> > +
> > +#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_EN (0x1 << 31)
> > +#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_SINGLE BIT(30)
> > +#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_AVG_EN BIT(29)
> > +#define IMX7D_REG_ADC_CH_CFG1_CHANNEL_SEL(x) ((x) << 24)
> > +
> > +#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_4 (0x0 <<
> 12)
> > +#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_8 (0x1 <<
> 12)
> > +#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_16 (0x2 << 12)
> > +#define IMX7D_REG_ADC_CH_CFG2_AVG_NUM_32 (0x3 << 12)
> > +
> > +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_4 (0x0 << 29)
> > +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_8 (0x1 << 29)
> > +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_16 (0x2 << 29)
> > +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_32 (0x3 << 29)
> > +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_64 (0x4 << 29)
> > +#define IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_128 (0x5 << 29)
> > +
> > +#define IMX7D_REG_ADC_ADC_CFG_ADC_CLK_DOWN BIT(31)
> > +#define IMX7D_REG_ADC_ADC_CFG_ADC_POWER_DOWN BIT(1)
> > +#define IMX7D_REG_ADC_ADC_CFG_ADC_EN BIT(0)
> > +
> > +#define IMX7D_REG_ADC_INT_CHA_COV_INT_EN BIT(8)
> > +#define IMX7D_REG_ADC_INT_CHB_COV_INT_EN BIT(9)
> > +#define IMX7D_REG_ADC_INT_CHC_COV_INT_EN BIT(10)
> > +#define IMX7D_REG_ADC_INT_CHD_COV_INT_EN BIT(11)
> > +#define IMX7D_REG_ADC_INT_CHANNEL_INT_EN
> (IMX7D_REG_ADC_INT_CHA_COV_INT_EN | \
> > +
> IMX7D_REG_ADC_INT_CHB_COV_INT_EN | \
> > +
> IMX7D_REG_ADC_INT_CHC_COV_INT_EN | \
> > +
> IMX7D_REG_ADC_INT_CHD_COV_INT_EN)
> > +#define IMX7D_REG_ADC_INT_STATUS_CHANNEL_INT_STATUS 0xf00
> > +#define IMX7D_REG_ADC_INT_STATUS_CHANNEL_CONV_TIME_OUT 0xf0000
> > +
> > +#define IMX7D_ADC_TIMEOUT msecs_to_jiffies(100)
> > +
> > +enum imx7d_adc_clk_pre_div {
> > + IMX7D_ADC_ANALOG_CLK_PRE_DIV_4,
> > + IMX7D_ADC_ANALOG_CLK_PRE_DIV_8,
> > + IMX7D_ADC_ANALOG_CLK_PRE_DIV_16,
> > + IMX7D_ADC_ANALOG_CLK_PRE_DIV_32,
> > + IMX7D_ADC_ANALOG_CLK_PRE_DIV_64,
> > + IMX7D_ADC_ANALOG_CLK_PRE_DIV_128,
> > +};
> > +
> > +enum imx7d_adc_average_num {
> > + IMX7D_ADC_AVERAGE_NUM_4,
> > + IMX7D_ADC_AVERAGE_NUM_8,
> > + IMX7D_ADC_AVERAGE_NUM_16,
> > + IMX7D_ADC_AVERAGE_NUM_32,
> > +};
> > +
> > +struct imx7d_adc_feature {
> > + enum imx7d_adc_clk_pre_div clk_pre_div;
> > + enum imx7d_adc_average_num avg_num;
> > +
> > + u32 core_time_unit; /* impact the sample rate */
> > +
> > + bool average_en;
> > +};
> > +
> > +struct imx7d_adc {
> > + struct device *dev;
> > + void __iomem *regs;
> > + struct clk *clk;
> > +
> > + u32 vref_uv;
> > + u32 value;
> > + u32 channel;
> > + u32 pre_div_num;
> > +
> > + struct regulator *vref;
> > + struct imx7d_adc_feature adc_feature;
> > +
> > + struct completion completion;
> > +};
> > +
> > +struct imx7d_adc_analogue_core_clk {
> > + u32 pre_div;
> > + u32 reg_config;
> > +};
> > +
> > +#define IMX7D_ADC_ANALOGUE_CLK_CONFIG(_pre_div, _reg_conf) { \
> > + .pre_div = (_pre_div), \
> > + .reg_config = (_reg_conf), \
> > +}
> > +
> > +static const struct imx7d_adc_analogue_core_clk
> imx7d_adc_analogue_clk[] = {
> > + IMX7D_ADC_ANALOGUE_CLK_CONFIG(4,
> IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_4),
> > + IMX7D_ADC_ANALOGUE_CLK_CONFIG(8,
> IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_8),
> > + IMX7D_ADC_ANALOGUE_CLK_CONFIG(16,
> IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_16),
> > + IMX7D_ADC_ANALOGUE_CLK_CONFIG(32,
> IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_32),
> > + IMX7D_ADC_ANALOGUE_CLK_CONFIG(64,
> IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_64),
> > + IMX7D_ADC_ANALOGUE_CLK_CONFIG(128,
> > +IMX7D_REG_ADC_TIMER_UNIT_PRE_DIV_128),
> > +};
> > +
> > +#define IMX7D_ADC_CHAN(_idx) { \
> > + .type = IIO_VOLTAGE, \
> > + .indexed = 1, \
> > + .channel = (_idx), \
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \
> > + BIT(IIO_CHAN_INFO_SAMP_FREQ), \
> > +}
> > +
> > +static const struct iio_chan_spec imx7d_adc_iio_channels[] = {
> > + IMX7D_ADC_CHAN(0),
> > + IMX7D_ADC_CHAN(1),
> > + IMX7D_ADC_CHAN(2),
> > + IMX7D_ADC_CHAN(3),
> > + IMX7D_ADC_CHAN(4),
> > + IMX7D_ADC_CHAN(5),
> > + IMX7D_ADC_CHAN(6),
> > + IMX7D_ADC_CHAN(7),
> > + IMX7D_ADC_CHAN(8),
> > + IMX7D_ADC_CHAN(9),
> > + IMX7D_ADC_CHAN(10),
> > + IMX7D_ADC_CHAN(11),
> > + IMX7D_ADC_CHAN(12),
> > + IMX7D_ADC_CHAN(13),
> > + IMX7D_ADC_CHAN(14),
> > + IMX7D_ADC_CHAN(15),
> > +};
> > +
> > +static const u32 imx7d_adc_average_num[] = {
> > + IMX7D_REG_ADC_CH_CFG2_AVG_NUM_4,
> > + IMX7D_REG_ADC_CH_CFG2_AVG_NUM_8,
> > + IMX7D_REG_ADC_CH_CFG2_AVG_NUM_16,
> > + IMX7D_REG_ADC_CH_CFG2_AVG_NUM_32,
> > +};
> > +
> > +static void imx7d_adc_feature_config(struct imx7d_adc *info) {
> > + info->adc_feature.clk_pre_div = IMX7D_ADC_ANALOG_CLK_PRE_DIV_4;
> > + info->adc_feature.avg_num = IMX7D_ADC_AVERAGE_NUM_32;
> > + info->adc_feature.core_time_unit = 1;
> > + info->adc_feature.average_en = true; }
> > +
> > +static void imx7d_adc_sample_rate_set(struct imx7d_adc *info) {
> > + struct imx7d_adc_feature *adc_feature = &info->adc_feature;
> > + struct imx7d_adc_analogue_core_clk adc_analogure_clk;
> > + u32 i;
> > + u32 tmp_cfg1;
> > + u32 sample_rate = 0;
> > +
> > + /*
> > + * Before sample set, disable channel A,B,C,D. Here we
> > + * clear the bit 31 of register REG_ADC_CH_A\B\C\D_CFG1.
> > + */
> > + for (i = 0; i < 4; i++) {
> > + tmp_cfg1 = readl(info->regs + i *
> IMX7D_EACH_CHANNEL_REG_OFFSET);
> > + tmp_cfg1 &= ~IMX7D_REG_ADC_CH_CFG1_CHANNEL_EN;
> > + writel(tmp_cfg1, info->regs + i *
> IMX7D_EACH_CHANNEL_REG_OFFSET);
> > + }
> > +
> > + adc_analogure_clk = imx7d_adc_analogue_clk[adc_feature-
> >clk_pre_div];
> > + sample_rate |= adc_analogure_clk.reg_config;
> > + info->pre_div_num = adc_analogure_clk.pre_div;
> > +
> > + sample_rate |= adc_feature->core_time_unit;
> > + writel(sample_rate, info->regs + IMX7D_REG_ADC_TIMER_UNIT); }
> > +
> > +static void imx7d_adc_hw_init(struct imx7d_adc *info) {
> > + u32 cfg;
> > +
> > + /* power up and enable adc analogue core */
> > + cfg = readl(info->regs + IMX7D_REG_ADC_ADC_CFG);
> > + cfg &= ~(IMX7D_REG_ADC_ADC_CFG_ADC_CLK_DOWN |
> IMX7D_REG_ADC_ADC_CFG_ADC_POWER_DOWN);
> > + cfg |= IMX7D_REG_ADC_ADC_CFG_ADC_EN;
> > + writel(cfg, info->regs + IMX7D_REG_ADC_ADC_CFG);
> > +
> > + /* enable channel A,B,C,D interrupt */
> > + writel(IMX7D_REG_ADC_INT_CHANNEL_INT_EN, info->regs +
> IMX7D_REG_ADC_INT_SIG_EN);
> > + writel(IMX7D_REG_ADC_INT_CHANNEL_INT_EN, info->regs +
> > +IMX7D_REG_ADC_INT_EN);
> > +
> > + imx7d_adc_sample_rate_set(info);
> > +}
> > +
> > +static void imx7d_adc_channel_set(struct imx7d_adc *info) {
> > + u32 cfg1 = 0;
> > + u32 cfg2;
> > + u32 channel;
> > +
> > + channel = info->channel;
> > +
> > + /* the channel choose single conversion, and enable average mode */
> > + cfg1 |= (IMX7D_REG_ADC_CH_CFG1_CHANNEL_EN |
> > + IMX7D_REG_ADC_CH_CFG1_CHANNEL_SINGLE);
> > + if (info->adc_feature.average_en)
> > + cfg1 |= IMX7D_REG_ADC_CH_CFG1_CHANNEL_AVG_EN;
> > +
> > + /*
> > + * physical channel 0 chose logical channel A
> > + * physical channel 1 chose logical channel B
> > + * physical channel 2 chose logical channel C
> > + * physical channel 3 chose logical channel D
> > + */
> > + cfg1 |= IMX7D_REG_ADC_CH_CFG1_CHANNEL_SEL(channel);
> > +
> > + /* read register REG_ADC_CH_A\B\C\D_CFG2, according to the channel
> chosen */
> > + cfg2 = readl(info->regs + IMX7D_EACH_CHANNEL_REG_OFFSET * channel +
> > +IMX7D_REG_ADC_CHANNEL_CFG2_BASE);
> > +
> > + cfg2 |= imx7d_adc_average_num[info->adc_feature.avg_num];
> > +
> > + /* write the register REG_ADC_CH_A\B\C\D_CFG2, according to the
> channel chosen */
> > + writel(cfg2, info->regs + IMX7D_EACH_CHANNEL_REG_OFFSET * channel +
> > +IMX7D_REG_ADC_CHANNEL_CFG2_BASE);
> Whilst line length limits are not set in stone it is best to stick to
> them if there is no good reason to not do so. Here it owuld make no real
> difference.
> > + writel(cfg1, info->regs + IMX7D_EACH_CHANNEL_REG_OFFSET * channel);
> > +}
> > +
> > +static u32 imx7d_adc_get_sample_rate(struct imx7d_adc *info) {
> > + /* input clock is always 24MHz */
> > + u32 input_clk = 24000000;
> > + u32 analogue_core_clk;
> > + u32 core_time_unit = info->adc_feature.core_time_unit;
> > + u32 tmp;
> > +
> > + analogue_core_clk = input_clk / info->pre_div_num;
> > + tmp = (core_time_unit + 1) * 6;
> > +
> > + return analogue_core_clk / tmp;
> > +}
> > +
> > +static int imx7d_adc_read_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan,
> > + int *val,
> > + int *val2,
> > + long mask)
> > +{
> > + struct imx7d_adc *info = iio_priv(indio_dev);
> > +
> > + u32 channel;
> > + long ret;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + mutex_lock(&indio_dev->mlock);
> > + reinit_completion(&info->completion);
> > +
> > + channel = chan->channel & 0x03;
> > + info->channel = channel;
> > + imx7d_adc_channel_set(info);
> > +
> > + ret = wait_for_completion_interruptible_timeout
> > + (&info->completion, IMX7D_ADC_TIMEOUT);
> > + if (ret == 0) {
> > + mutex_unlock(&indio_dev->mlock);
> > + return -ETIMEDOUT;
> > + }
> > + if (ret < 0) {
> > + mutex_unlock(&indio_dev->mlock);
> > + return ret;
> > + }
> > +
> > + *val = info->value;
> > + mutex_unlock(&indio_dev->mlock);
> > + return IIO_VAL_INT;
> > +
> > + case IIO_CHAN_INFO_SCALE:
> > + info->vref_uv = regulator_get_voltage(info->vref);
> > + *val = info->vref_uv / 1000;
> > + *val2 = 12;
> > + return IIO_VAL_FRACTIONAL_LOG2;
> > +
> > + case IIO_CHAN_INFO_SAMP_FREQ:
> > + *val = imx7d_adc_get_sample_rate(info);
> > + return IIO_VAL_INT;
> > +
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static int imx7d_adc_read_data(struct imx7d_adc *info) {
> > + u32 channel;
> > + u32 value;
> > +
> > + channel = info->channel & 0x03;
> > +
> > + /*
> > + * channel A and B conversion result share one register,
> > + * bit[27~16] is the channel B conversion result,
> > + * bit[11~0] is the channel A conversion result.
> > + * channel C and D is the same.
> > + */
> > + if (channel < 2)
> > + value = readl(info->regs + IMX7D_REG_ADC_CHA_B_CNV_RSLT);
> > + else
> > + value = readl(info->regs + IMX7D_REG_ADC_CHC_D_CNV_RSLT);
> > + if (channel & 0x1) /* channel B or D */
> > + value = (value >> 16) & 0xFFF;
> > + else /* channel A or C */
> > + value &= 0xFFF;
> > +
> > + return value;
> > +}
> > +
> > +static irqreturn_t imx7d_adc_isr(int irq, void *dev_id) {
> > + struct imx7d_adc *info = (struct imx7d_adc *)dev_id;
> > + int status;
> > +
> > + status = readl(info->regs + IMX7D_REG_ADC_INT_STATUS);
> > + if (status & IMX7D_REG_ADC_INT_STATUS_CHANNEL_INT_STATUS) {
> > + info->value = imx7d_adc_read_data(info);
> > + complete(&info->completion);
> > +
> > + /*
> > + * The register IMX7D_REG_ADC_INT_STATUS can't clear
> > + * itself after read operation, need software to write
> > + * 0 to the related bit. Here we clear the channel A/B/C/D
> > + * conversion finished flag.
> > + */
> > + status &= ~IMX7D_REG_ADC_INT_STATUS_CHANNEL_INT_STATUS;
> > + writel(status, info->regs + IMX7D_REG_ADC_INT_STATUS);
> > + }
> > +
> > + /*
> > + * If the channel A/B/C/D conversion timeout, report it and clear
> these
> > + * timeout flags.
> > + */
> > + if (status & IMX7D_REG_ADC_INT_STATUS_CHANNEL_CONV_TIME_OUT) {
> > + pr_err("%s: ADC got conversion time out interrupt: 0x%08x\n",
> > + dev_name(info->dev), status);
> > + status &= ~IMX7D_REG_ADC_INT_STATUS_CHANNEL_CONV_TIME_OUT;
> > + writel(status, info->regs + IMX7D_REG_ADC_INT_STATUS);
> > + }
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int imx7d_adc_reg_access(struct iio_dev *indio_dev,
> > + unsigned reg, unsigned writeval,
> > + unsigned *readval)
> > +{
> > + struct imx7d_adc *info = iio_priv(indio_dev);
> > +
> > + if (!readval || reg % 4 || reg > IMX7D_REG_ADC_ADC_CFG)
> > + return -EINVAL;
> > +
> > + *readval = readl(info->regs + reg);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct iio_info imx7d_adc_iio_info = {
> > + .driver_module = THIS_MODULE,
> > + .read_raw = &imx7d_adc_read_raw,
> > + .debugfs_reg_access = &imx7d_adc_reg_access, };
> > +
> > +static const struct of_device_id imx7d_adc_match[] = {
> > + { .compatible = "fsl,imx7d-adc", },
> > + { /* sentinel */ }
> > +};
> > +MODULE_DEVICE_TABLE(of, imx7d_adc_match);
> > +
> > +static void imx7d_adc_power_down(struct imx7d_adc *info) {
> > + u32 adc_cfg;
> > +
> > + adc_cfg = readl(info->regs + IMX7D_REG_ADC_ADC_CFG);
> > + adc_cfg |= IMX7D_REG_ADC_ADC_CFG_ADC_CLK_DOWN |
> > + IMX7D_REG_ADC_ADC_CFG_ADC_POWER_DOWN;
> > + adc_cfg &= ~IMX7D_REG_ADC_ADC_CFG_ADC_EN;
> > + writel(adc_cfg, info->regs + IMX7D_REG_ADC_ADC_CFG); }
> > +
> > +static int imx7d_adc_probe(struct platform_device *pdev) {
> > + struct imx7d_adc *info;
> > + struct iio_dev *indio_dev;
> > + struct resource *mem;
> > + int irq;
> > + int ret;
> > +
> > + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*info));
> > + if (!indio_dev) {
> > + dev_err(&pdev->dev, "Failed allocating iio device\n");
> > + return -ENOMEM;
> > + }
> > +
> > + info = iio_priv(indio_dev);
> > + info->dev = &pdev->dev;
> > +
> > + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + info->regs = devm_ioremap_resource(&pdev->dev, mem);
> > + if (IS_ERR(info->regs)) {
> > + ret = PTR_ERR(info->regs);
> > + dev_err(&pdev->dev, "Failed to remap adc memory, err = %d\n",
> ret);
> > + return ret;
> > + }
> > +
> > + irq = platform_get_irq(pdev, 0);
> > + if (irq < 0) {
> > + dev_err(&pdev->dev, "No irq resource?\n");
> > + return irq;
> > + }
> > +
> > + info->clk = devm_clk_get(&pdev->dev, "adc");
> > + if (IS_ERR(info->clk)) {
> > + ret = PTR_ERR(info->clk);
> > + dev_err(&pdev->dev, "Failed getting clock, err = %d\n", ret);
> > + return ret;
> > + }
> > +
> > + info->vref = devm_regulator_get(&pdev->dev, "vref");
> > + if (IS_ERR(info->vref)) {
> > + ret = PTR_ERR(info->vref);
> > + dev_err(&pdev->dev, "Failed getting reference voltage, err
> = %d\n", ret);
> > + return ret;
> > + }
> > +
> > + ret = regulator_enable(info->vref);
> > + if (ret) {
> > + dev_err(&pdev->dev, "Can't enable adc reference top voltage,
> err = %d\n", ret);
> > + return ret;
> > + }
> > +
> > + platform_set_drvdata(pdev, indio_dev);
> > +
> > + init_completion(&info->completion);
> > +
> > + indio_dev->name = dev_name(&pdev->dev);
> > + indio_dev->dev.parent = &pdev->dev;
> > + indio_dev->info = &imx7d_adc_iio_info;
> > + indio_dev->modes = INDIO_DIRECT_MODE;
> > + indio_dev->channels = imx7d_adc_iio_channels;
> > + indio_dev->num_channels = ARRAY_SIZE(imx7d_adc_iio_channels);
> > +
> > + ret = clk_prepare_enable(info->clk);
> > + if (ret) {
> > + dev_err(&pdev->dev,
> > + "Could not prepare or enable the clock.\n");
> > + goto error_adc_clk_enable;
> > + }
> > +
> > + ret = devm_request_irq(info->dev, irq,
> > + imx7d_adc_isr, 0,
> > + dev_name(&pdev->dev), info);
> > + if (ret < 0) {
> > + dev_err(&pdev->dev, "Failed requesting irq, irq = %d\n", irq);
> > + goto error_iio_device_register;
> It's trivial but this goto label naming isn't accurate as the device
> register doesn't occur for a few more lines...
> > + }
> > +
> > + imx7d_adc_feature_config(info);
> > + imx7d_adc_hw_init(info);
> > +
> > + ret = iio_device_register(indio_dev);
> > + if (ret) {
> > + imx7d_adc_power_down(info);
> > + dev_err(&pdev->dev, "Couldn't register the device.\n");
> > + goto error_iio_device_register;
> > + }
> > +
> > + return 0;
> > +
> > +error_iio_device_register:
> > + clk_disable_unprepare(info->clk);
> > +error_adc_clk_enable:
> > + regulator_disable(info->vref);
> > +
> > + return ret;
> > +}
> > +
> > +static int imx7d_adc_remove(struct platform_device *pdev) {
> > + struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> > + struct imx7d_adc *info = iio_priv(indio_dev);
> > +
> > + imx7d_adc_power_down(info);
> I might fix this up, but the power down definitely wants to occur 'after'
> you have removed the userspace interface (so after the
> iio_device_unregister call).
>
> > +
> > + iio_device_unregister(indio_dev);
> > + clk_disable_unprepare(info->clk);
> > + regulator_disable(info->vref);
> > +
> > + return 0;
> > +}
> > +
> > +static int __maybe_unused imx7d_adc_suspend(struct device *dev) {
> > + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> > + struct imx7d_adc *info = iio_priv(indio_dev);
> > +
> > + imx7d_adc_power_down(info);
> > +
> > + clk_disable_unprepare(info->clk);
> > + regulator_disable(info->vref);
> > +
> > + return 0;
> > +}
> > +
> > +static int __maybe_unused imx7d_adc_resume(struct device *dev) {
> > + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> > + struct imx7d_adc *info = iio_priv(indio_dev);
> > + int ret;
> > +
> > + ret = regulator_enable(info->vref);
> > + if (ret) {
> > + dev_err(info->dev,
> > + "Can't enable adc reference top voltage, err = %d\n",
> ret);
> > + return ret;
> > + }
> > +
> > + ret = clk_prepare_enable(info->clk);
> > + if (ret) {
> > + dev_err(info->dev,
> > + "Could not prepare or enable clock.\n");
> > + regulator_disable(info->vref);
> > + return ret;
> > + }
> > +
> > + imx7d_adc_hw_init(info);
> > +
> > + return 0;
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(imx7d_adc_pm_ops, imx7d_adc_suspend,
> > +imx7d_adc_resume);
> > +
> > +static struct platform_driver imx7d_adc_driver = {
> > + .probe = imx7d_adc_probe,
> > + .remove = imx7d_adc_remove,
> > + .driver = {
> > + .name = "imx7d_adc",
> > + .of_match_table = imx7d_adc_match,
> > + .pm = &imx7d_adc_pm_ops,
> > + },
> > +};
> > +
> > +module_platform_driver(imx7d_adc_driver);
> > +
> > +MODULE_AUTHOR("Haibo Chen <[email protected]>");
> > +MODULE_DESCRIPTION("Freeacale IMX7D ADC driver"); MODULE_LICENSE("GPL
> > +v2");
> >
On Sat, Dec 12, 2015 at 04:27:40PM +0000, Jonathan Cameron wrote:
> On 08/12/15 10:26, Haibo Chen wrote:
> > Add imx7d ADC support.
> >
> > Signed-off-by: Haibo Chen <[email protected]>
> The driver is now working its way in the direction of linux-next via
> Greg KHs tree. I'm happy to take these changes as well, but would imagine
> they are better routed through the relevant imx trees.
Yes. I just applied 2 dts patches on i.MX tree. Thanks.
Shawn