Everyone:
This series contains various improvements (at least in my mind) and
fixes that I made to tc358767 while working with the code of the
driver. Hopefuly each patch is self explanatory.
Feedback is welcome!
Thanks,
Andrey Smirnov
Changes since [v4]:
- tc_pllupdate_pllen() renamed to tc_pllupdate()
- Collected Reviewed-bys from Andrzej for the rest of the series
Changes since [v3]:
- Collected Reviewed-bys from Andrzej
- Dropped explicit check for -ETIMEDOUT in "drm/bridge: tc358767:
Simplify polling in tc_main_link_setup()" for consistency
- AUX transfer code converted to user regmap_raw_read(),
regmap_raw_write()
Changes since [v2]:
- Patchset rebased on top of v4 of Tomi's series that recently
went in (https://patchwork.freedesktop.org/series/58176/#rev5)
- AUX transfer code converted to user regmap_bulk_read(),
regmap_bulk_write()
Changes since [v1]:
- Patchset rebased on top of
https://patchwork.freedesktop.org/series/58176/
- Patches to remove both tc_write() and tc_read() helpers added
- Patches to rework AUX transfer code added
- Both "drm/bridge: tc358767: Simplify polling in
tc_main_link_setup()" and "drm/bridge: tc358767: Simplify
polling in tc_link_training()" changed to use tc_poll_timeout()
instead of regmap_read_poll_timeout()
[v4] lkml.kernel.org/r/[email protected]
[v3] lkml.kernel.org/r/[email protected]
[v2] lkml.kernel.org/r/[email protected]
[v1] lkml.kernel.org/r/[email protected]
Andrey Smirnov (15):
drm/bridge: tc358767: Simplify tc_poll_timeout()
drm/bridge: tc358767: Simplify polling in tc_main_link_setup()
drm/bridge: tc358767: Simplify polling in tc_link_training()
drm/bridge: tc358767: Simplify tc_set_video_mode()
drm/bridge: tc358767: Drop custom tc_write()/tc_read() accessors
drm/bridge: tc358767: Simplify AUX data read
drm/bridge: tc358767: Simplify AUX data write
drm/bridge: tc358767: Increase AUX transfer length limit
drm/bridge: tc358767: Use reported AUX transfer size
drm/bridge: tc358767: Add support for address-only I2C transfers
drm/bridge: tc358767: Introduce tc_set_syspllparam()
drm/bridge: tc358767: Introduce tc_pllupdate()
drm/bridge: tc358767: Simplify tc_aux_wait_busy()
drm/bridge: tc358767: Drop unnecessary 8 byte buffer
drm/bridge: tc358767: Replace magic number in tc_main_link_enable()
drivers/gpu/drm/bridge/tc358767.c | 648 +++++++++++++++++-------------
1 file changed, 372 insertions(+), 276 deletions(-)
--
2.21.0
Replace explicit polling loop with equivalent call to
tc_poll_timeout() for brevity. No functional change intended.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 12 +++---------
1 file changed, 3 insertions(+), 9 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index fb8a1942ec54..f463ef6d4271 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -774,7 +774,6 @@ static int tc_main_link_enable(struct tc_data *tc)
struct device *dev = tc->dev;
unsigned int rate;
u32 dp_phy_ctrl;
- int timeout;
u32 value;
int ret;
u8 tmp[8];
@@ -831,15 +830,10 @@ static int tc_main_link_enable(struct tc_data *tc)
dp_phy_ctrl &= ~(DP_PHY_RST | PHY_M1_RST | PHY_M0_RST);
tc_write(DP_PHY_CTRL, dp_phy_ctrl);
- timeout = 1000;
- do {
- tc_read(DP_PHY_CTRL, &value);
- udelay(1);
- } while ((!(value & PHY_RDY)) && (--timeout));
-
- if (timeout == 0) {
+ ret = tc_poll_timeout(tc, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 1, 1000);
+ if (ret) {
dev_err(dev, "timeout waiting for phy become ready");
- return -ETIMEDOUT;
+ return ret;
}
/* Set misc: 8 bits per color */
--
2.21.0
Replace explicit polling in tc_link_training() with equivalent call to
tc_poll_timeout() for simplicity. No functional change intended (not
including slightly altered debug output).
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 15 ++++++---------
1 file changed, 6 insertions(+), 9 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index f463ef6d4271..31f5045e7e42 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -748,22 +748,19 @@ static int tc_set_video_mode(struct tc_data *tc,
static int tc_wait_link_training(struct tc_data *tc)
{
- u32 timeout = 1000;
u32 value;
int ret;
- do {
- udelay(1);
- tc_read(DP0_LTSTAT, &value);
- } while ((!(value & LT_LOOPDONE)) && (--timeout));
-
- if (timeout == 0) {
+ ret = tc_poll_timeout(tc, DP0_LTSTAT, LT_LOOPDONE,
+ LT_LOOPDONE, 1, 1000);
+ if (ret) {
dev_err(tc->dev, "Link training timeout waiting for LT_LOOPDONE!\n");
- return -ETIMEDOUT;
+ return ret;
}
- return (value >> 8) & 0x7;
+ tc_read(DP0_LTSTAT, &value);
+ return (value >> 8) & 0x7;
err:
return ret;
}
--
2.21.0
Simplify tc_set_video_mode() by replacing explicit shifting using
macros from <linux/bitfield.h>. No functional change intended.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 106 ++++++++++++++++++++++--------
1 file changed, 78 insertions(+), 28 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 31f5045e7e42..5b78021d6c5b 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -24,6 +24,7 @@
* GNU General Public License for more details.
*/
+#include <linux/bitfield.h>
#include <linux/clk.h>
#include <linux/device.h>
#include <linux/gpio/consumer.h>
@@ -56,6 +57,7 @@
/* Video Path */
#define VPCTRL0 0x0450
+#define VSDELAY GENMASK(31, 20)
#define OPXLFMT_RGB666 (0 << 8)
#define OPXLFMT_RGB888 (1 << 8)
#define FRMSYNC_DISABLED (0 << 4) /* Video Timing Gen Disabled */
@@ -63,9 +65,17 @@
#define MSF_DISABLED (0 << 0) /* Magic Square FRC disabled */
#define MSF_ENABLED (1 << 0) /* Magic Square FRC enabled */
#define HTIM01 0x0454
+#define HPW GENMASK(8, 0)
+#define HBPR GENMASK(24, 16)
#define HTIM02 0x0458
+#define HDISPR GENMASK(10, 0)
+#define HFPR GENMASK(24, 16)
#define VTIM01 0x045c
+#define VSPR GENMASK(7, 0)
+#define VBPR GENMASK(23, 16)
#define VTIM02 0x0460
+#define VFPR GENMASK(23, 16)
+#define VDISPR GENMASK(10, 0)
#define VFUEN0 0x0464
#define VFUEN BIT(0) /* Video Frame Timing Upload */
@@ -108,14 +118,28 @@
/* Main Channel */
#define DP0_SECSAMPLE 0x0640
#define DP0_VIDSYNCDELAY 0x0644
+#define VID_SYNC_DLY GENMASK(15, 0)
+#define THRESH_DLY GENMASK(31, 16)
+
#define DP0_TOTALVAL 0x0648
+#define H_TOTAL GENMASK(15, 0)
+#define V_TOTAL GENMASK(31, 16)
#define DP0_STARTVAL 0x064c
+#define H_START GENMASK(15, 0)
+#define V_START GENMASK(31, 16)
#define DP0_ACTIVEVAL 0x0650
+#define H_ACT GENMASK(15, 0)
+#define V_ACT GENMASK(31, 16)
+
#define DP0_SYNCVAL 0x0654
+#define VS_WIDTH GENMASK(30, 16)
+#define HS_WIDTH GENMASK(14, 0)
#define SYNCVAL_HS_POL_ACTIVE_LOW (1 << 15)
#define SYNCVAL_VS_POL_ACTIVE_LOW (1 << 31)
#define DP0_MISC 0x0658
#define TU_SIZE_RECOMMENDED (63) /* LSCLK cycles per TU */
+#define MAX_TU_SYMBOL GENMASK(28, 23)
+#define TU_SIZE GENMASK(21, 16)
#define BPC_6 (0 << 5)
#define BPC_8 (1 << 5)
@@ -192,6 +216,12 @@
/* Test & Debug */
#define TSTCTL 0x0a00
+#define COLOR_R GENMASK(31, 24)
+#define COLOR_G GENMASK(23, 16)
+#define COLOR_B GENMASK(15, 8)
+#define ENI2CFILTER BIT(4)
+#define COLOR_BAR_MODE GENMASK(1, 0)
+#define COLOR_BAR_MODE_BARS 2
#define PLL_DBG 0x0a04
static bool tc_test_pattern;
@@ -672,6 +702,7 @@ static int tc_set_video_mode(struct tc_data *tc,
int upper_margin = mode->vtotal - mode->vsync_end;
int lower_margin = mode->vsync_start - mode->vdisplay;
int vsync_len = mode->vsync_end - mode->vsync_start;
+ u32 dp0_syncval;
/*
* Recommended maximum number of symbols transferred in a transfer unit:
@@ -696,50 +727,69 @@ static int tc_set_video_mode(struct tc_data *tc,
* assume we do not need any delay when DPI is a source of
* sync signals
*/
- tc_write(VPCTRL0, (0 << 20) /* VSDELAY */ |
+ tc_write(VPCTRL0,
+ FIELD_PREP(VSDELAY, 0) |
OPXLFMT_RGB888 | FRMSYNC_DISABLED | MSF_DISABLED);
- tc_write(HTIM01, (ALIGN(left_margin, 2) << 16) | /* H back porch */
- (ALIGN(hsync_len, 2) << 0)); /* Hsync */
- tc_write(HTIM02, (ALIGN(right_margin, 2) << 16) | /* H front porch */
- (ALIGN(mode->hdisplay, 2) << 0)); /* width */
- tc_write(VTIM01, (upper_margin << 16) | /* V back porch */
- (vsync_len << 0)); /* Vsync */
- tc_write(VTIM02, (lower_margin << 16) | /* V front porch */
- (mode->vdisplay << 0)); /* height */
+ tc_write(HTIM01,
+ FIELD_PREP(HBPR, ALIGN(left_margin, 2)) |
+ FIELD_PREP(HPW, ALIGN(hsync_len, 2)));
+ tc_write(HTIM02,
+ FIELD_PREP(HDISPR, ALIGN(mode->hdisplay, 2)) |
+ FIELD_PREP(HFPR, ALIGN(right_margin, 2)));
+ tc_write(VTIM01,
+ FIELD_PREP(VBPR, upper_margin) |
+ FIELD_PREP(VSPR, vsync_len));
+ tc_write(VTIM02,
+ FIELD_PREP(VFPR, lower_margin) |
+ FIELD_PREP(VDISPR, mode->vdisplay));
tc_write(VFUEN0, VFUEN); /* update settings */
/* Test pattern settings */
tc_write(TSTCTL,
- (120 << 24) | /* Red Color component value */
- (20 << 16) | /* Green Color component value */
- (99 << 8) | /* Blue Color component value */
- (1 << 4) | /* Enable I2C Filter */
- (2 << 0) | /* Color bar Mode */
- 0);
+ FIELD_PREP(COLOR_R, 120) |
+ FIELD_PREP(COLOR_G, 20) |
+ FIELD_PREP(COLOR_B, 99) |
+ ENI2CFILTER |
+ FIELD_PREP(COLOR_BAR_MODE, COLOR_BAR_MODE_BARS));
/* DP Main Stream Attributes */
vid_sync_dly = hsync_len + left_margin + mode->hdisplay;
tc_write(DP0_VIDSYNCDELAY,
- (max_tu_symbol << 16) | /* thresh_dly */
- (vid_sync_dly << 0));
+ FIELD_PREP(THRESH_DLY, max_tu_symbol) |
+ FIELD_PREP(VID_SYNC_DLY, vid_sync_dly));
- tc_write(DP0_TOTALVAL, (mode->vtotal << 16) | (mode->htotal));
+ tc_write(DP0_TOTALVAL,
+ FIELD_PREP(H_TOTAL, mode->htotal) |
+ FIELD_PREP(V_TOTAL, mode->vtotal));
tc_write(DP0_STARTVAL,
- ((upper_margin + vsync_len) << 16) |
- ((left_margin + hsync_len) << 0));
+ FIELD_PREP(H_START, left_margin + hsync_len) |
+ FIELD_PREP(V_START, upper_margin + vsync_len));
+
+ tc_write(DP0_ACTIVEVAL,
+ FIELD_PREP(V_ACT, mode->vdisplay) |
+ FIELD_PREP(H_ACT, mode->hdisplay));
+
+ dp0_syncval = FIELD_PREP(VS_WIDTH, vsync_len) |
+ FIELD_PREP(HS_WIDTH, hsync_len);
+
+ if (mode->flags & DRM_MODE_FLAG_NVSYNC)
+ dp0_syncval |= SYNCVAL_VS_POL_ACTIVE_LOW;
- tc_write(DP0_ACTIVEVAL, (mode->vdisplay << 16) | (mode->hdisplay));
+ if (mode->flags & DRM_MODE_FLAG_NHSYNC)
+ dp0_syncval |= SYNCVAL_HS_POL_ACTIVE_LOW;
- tc_write(DP0_SYNCVAL, (vsync_len << 16) | (hsync_len << 0) |
- ((mode->flags & DRM_MODE_FLAG_NHSYNC) ? SYNCVAL_HS_POL_ACTIVE_LOW : 0) |
- ((mode->flags & DRM_MODE_FLAG_NVSYNC) ? SYNCVAL_VS_POL_ACTIVE_LOW : 0));
+ tc_write(DP0_SYNCVAL, dp0_syncval);
- tc_write(DPIPXLFMT, VS_POL_ACTIVE_LOW | HS_POL_ACTIVE_LOW |
- DE_POL_ACTIVE_HIGH | SUB_CFG_TYPE_CONFIG1 | DPI_BPP_RGB888);
+ tc_write(DPIPXLFMT,
+ VS_POL_ACTIVE_LOW | HS_POL_ACTIVE_LOW |
+ DE_POL_ACTIVE_HIGH | SUB_CFG_TYPE_CONFIG1 |
+ DPI_BPP_RGB888);
- tc_write(DP0_MISC, (max_tu_symbol << 23) | (TU_SIZE_RECOMMENDED << 16) |
- BPC_8);
+ tc_write(DP0_MISC,
+ FIELD_PREP(MAX_TU_SYMBOL, max_tu_symbol) |
+ FIELD_PREP(TU_SIZE, TU_SIZE_RECOMMENDED) |
+ BPC_8);
return 0;
err:
--
2.21.0
Simplify AUX data write by dropping index arithmetic and shifting and
replacing it with a call to a helper function that does two things:
1. Copies user-provided data into a write buffer
2. Transfers contents of the write buffer to up to 4 32-bit
registers on the chip
Note that separate data endianness fix:
tmp = (tmp << 8) | buf[i];
that was reserved for DP_AUX_I2C_WRITE looks really strange, since it
will place data differently depending on the passed user-data
size. E.g. for a write of 1 byte, data transferred to the chip would
look like:
[byte0] [dummy1] [dummy2] [dummy3]
whereas for a write of 4 bytes we'd get:
[byte3] [byte2] [byte1] [byte0]
Since there's no indication in the datasheet that I2C write buffer
should be treated differently than AUX write buffer and no comment in
the original code explaining why it was done this way, that special
I2C write buffer transformation was dropped in this patch.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 48 +++++++++++++++++--------------
1 file changed, 26 insertions(+), 22 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 7152b44db8a3..e60692b8cd69 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -321,6 +321,21 @@ static int tc_aux_get_status(struct tc_data *tc, u8 *reply)
return 0;
}
+static int tc_aux_write_data(struct tc_data *tc, const void *data,
+ size_t size)
+{
+ u32 auxwdata[DP_AUX_MAX_PAYLOAD_BYTES / sizeof(u32)] = { 0 };
+ int ret, count = ALIGN(size, sizeof(u32));
+
+ memcpy(auxwdata, data, size);
+
+ ret = regmap_raw_write(tc->regmap, DP0_AUXWDATA(0), auxwdata, count);
+ if (ret)
+ return ret;
+
+ return size;
+}
+
static int tc_aux_read_data(struct tc_data *tc, void *data, size_t size)
{
u32 auxrdata[DP_AUX_MAX_PAYLOAD_BYTES / sizeof(u32)];
@@ -341,9 +356,6 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
struct tc_data *tc = aux_to_tc(aux);
size_t size = min_t(size_t, 8, msg->size);
u8 request = msg->request & ~DP_AUX_I2C_MOT;
- u8 *buf = msg->buffer;
- u32 tmp = 0;
- int i = 0;
int ret;
if (size == 0)
@@ -353,25 +365,17 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
if (ret)
return ret;
- if (request == DP_AUX_I2C_WRITE || request == DP_AUX_NATIVE_WRITE) {
- /* Store data */
- while (i < size) {
- if (request == DP_AUX_NATIVE_WRITE)
- tmp = tmp | (buf[i] << (8 * (i & 0x3)));
- else
- tmp = (tmp << 8) | buf[i];
- i++;
- if (((i % 4) == 0) || (i == size)) {
- ret = regmap_write(tc->regmap,
- DP0_AUXWDATA((i - 1) >> 2),
- tmp);
- if (ret)
- return ret;
- tmp = 0;
- }
- }
- } else if (request != DP_AUX_I2C_READ &&
- request != DP_AUX_NATIVE_READ) {
+ switch (request) {
+ case DP_AUX_NATIVE_READ:
+ case DP_AUX_I2C_READ:
+ break;
+ case DP_AUX_NATIVE_WRITE:
+ case DP_AUX_I2C_WRITE:
+ ret = tc_aux_write_data(tc, msg->buffer, size);
+ if (ret < 0)
+ return ret;
+ break;
+ default:
return -EINVAL;
}
--
2.21.0
We don't need 8 byte array, DP_LINK_STATUS_SIZE (6) should be
enough. This also gets rid of a magic number as a bonus.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 81ed359487c7..b403c7bad156 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -874,7 +874,7 @@ static int tc_main_link_enable(struct tc_data *tc)
u32 dp_phy_ctrl;
u32 value;
int ret;
- u8 tmp[8];
+ u8 tmp[DP_LINK_STATUS_SIZE];
dev_dbg(tc->dev, "link enable\n");
--
2.21.0
tc_get_display_props() never reads more than a byte via AUX, so
there's no need to reserve 8 for that purpose. No function change
intended.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 13 ++++++-------
1 file changed, 6 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 01ca92a6d9c8..81ed359487c7 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -661,8 +661,7 @@ static int tc_aux_link_setup(struct tc_data *tc)
static int tc_get_display_props(struct tc_data *tc)
{
int ret;
- /* temp buffer */
- u8 tmp[8];
+ u8 reg;
/* Read DP Rx Link Capability */
ret = drm_dp_link_probe(&tc->aux, &tc->link.base);
@@ -678,21 +677,21 @@ static int tc_get_display_props(struct tc_data *tc)
tc->link.base.num_lanes = 2;
}
- ret = drm_dp_dpcd_readb(&tc->aux, DP_MAX_DOWNSPREAD, tmp);
+ ret = drm_dp_dpcd_readb(&tc->aux, DP_MAX_DOWNSPREAD, ®);
if (ret < 0)
goto err_dpcd_read;
- tc->link.spread = tmp[0] & DP_MAX_DOWNSPREAD_0_5;
+ tc->link.spread = reg & DP_MAX_DOWNSPREAD_0_5;
- ret = drm_dp_dpcd_readb(&tc->aux, DP_MAIN_LINK_CHANNEL_CODING, tmp);
+ ret = drm_dp_dpcd_readb(&tc->aux, DP_MAIN_LINK_CHANNEL_CODING, ®);
if (ret < 0)
goto err_dpcd_read;
tc->link.scrambler_dis = false;
/* read assr */
- ret = drm_dp_dpcd_readb(&tc->aux, DP_EDP_CONFIGURATION_SET, tmp);
+ ret = drm_dp_dpcd_readb(&tc->aux, DP_EDP_CONFIGURATION_SET, ®);
if (ret < 0)
goto err_dpcd_read;
- tc->link.assr = tmp[0] & DP_ALTERNATE_SCRAMBLER_RESET_ENABLE;
+ tc->link.assr = reg & DP_ALTERNATE_SCRAMBLER_RESET_ENABLE;
dev_dbg(tc->dev, "DPCD rev: %d.%d, rate: %s, lanes: %d, framing: %s\n",
tc->link.base.revision >> 4, tc->link.base.revision & 0x0f,
--
2.21.0
Move common code converting clock rate to an appropriate constant and
configuring SYS_PLLPARAM register into a separate routine and convert
the rest of the code to use it. No functional change intended.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 46 +++++++++++--------------------
1 file changed, 16 insertions(+), 30 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 4bb9b15e1324..ac55b59249e3 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -581,35 +581,40 @@ static int tc_stream_clock_calc(struct tc_data *tc)
return regmap_write(tc->regmap, DP0_VIDMNGEN1, 32768);
}
-static int tc_aux_link_setup(struct tc_data *tc)
+static int tc_set_syspllparam(struct tc_data *tc)
{
unsigned long rate;
- u32 dp0_auxcfg1;
- u32 value;
- int ret;
+ u32 pllparam = SYSCLK_SEL_LSCLK | LSCLK_DIV_2;
rate = clk_get_rate(tc->refclk);
switch (rate) {
case 38400000:
- value = REF_FREQ_38M4;
+ pllparam |= REF_FREQ_38M4;
break;
case 26000000:
- value = REF_FREQ_26M;
+ pllparam |= REF_FREQ_26M;
break;
case 19200000:
- value = REF_FREQ_19M2;
+ pllparam |= REF_FREQ_19M2;
break;
case 13000000:
- value = REF_FREQ_13M;
+ pllparam |= REF_FREQ_13M;
break;
default:
dev_err(tc->dev, "Invalid refclk rate: %lu Hz\n", rate);
return -EINVAL;
}
+ return regmap_write(tc->regmap, SYS_PLLPARAM, pllparam);
+}
+
+static int tc_aux_link_setup(struct tc_data *tc)
+{
+ int ret;
+ u32 dp0_auxcfg1;
+
/* Setup DP-PHY / PLL */
- value |= SYSCLK_SEL_LSCLK | LSCLK_DIV_2;
- ret = regmap_write(tc->regmap, SYS_PLLPARAM, value);
+ ret = tc_set_syspllparam(tc);
if (ret)
goto err;
@@ -868,7 +873,6 @@ static int tc_main_link_enable(struct tc_data *tc)
{
struct drm_dp_aux *aux = &tc->aux;
struct device *dev = tc->dev;
- unsigned int rate;
u32 dp_phy_ctrl;
u32 value;
int ret;
@@ -896,25 +900,7 @@ static int tc_main_link_enable(struct tc_data *tc)
if (ret)
return ret;
- rate = clk_get_rate(tc->refclk);
- switch (rate) {
- case 38400000:
- value = REF_FREQ_38M4;
- break;
- case 26000000:
- value = REF_FREQ_26M;
- break;
- case 19200000:
- value = REF_FREQ_19M2;
- break;
- case 13000000:
- value = REF_FREQ_13M;
- break;
- default:
- return -EINVAL;
- }
- value |= SYSCLK_SEL_LSCLK | LSCLK_DIV_2;
- ret = regmap_write(tc->regmap, SYS_PLLPARAM, value);
+ ret = tc_set_syspllparam(tc);
if (ret)
return ret;
--
2.21.0
We never pass anything but 100 as timeout_ms to tc_aux_wait_busy(), so
we may as well hardcode that value and simplify function's signature.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 9 ++++-----
1 file changed, 4 insertions(+), 5 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 28df53f7c349..01ca92a6d9c8 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -294,10 +294,9 @@ static inline int tc_poll_timeout(struct tc_data *tc, unsigned int addr,
sleep_us, timeout_us);
}
-static int tc_aux_wait_busy(struct tc_data *tc, unsigned int timeout_ms)
+static int tc_aux_wait_busy(struct tc_data *tc)
{
- return tc_poll_timeout(tc, DP0_AUXSTATUS, AUX_BUSY, 0,
- 1000, 1000 * timeout_ms);
+ return tc_poll_timeout(tc, DP0_AUXSTATUS, AUX_BUSY, 0, 1000, 100000);
}
static int tc_aux_write_data(struct tc_data *tc, const void *data,
@@ -350,7 +349,7 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
u32 auxstatus;
int ret;
- ret = tc_aux_wait_busy(tc, 100);
+ ret = tc_aux_wait_busy(tc);
if (ret)
return ret;
@@ -377,7 +376,7 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
if (ret)
return ret;
- ret = tc_aux_wait_busy(tc, 100);
+ ret = tc_aux_wait_busy(tc);
if (ret)
return ret;
--
2.21.0
Transfer size of zero means a request to do an address-only
transfer. Since the HW support this, we probably shouldn't be just
ignoring such requests. While at it allow DP_AUX_I2C_MOT flag to pass
through, since it is supported by the HW as well.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 30 +++++++++++++++++++++++-------
1 file changed, 23 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 7d0fbb12195b..4bb9b15e1324 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -145,6 +145,8 @@
/* AUX channel */
#define DP0_AUXCFG0 0x0660
+#define DP0_AUXCFG0_BSIZE GENMASK(11, 8)
+#define DP0_AUXCFG0_ADDR_ONLY BIT(4)
#define DP0_AUXCFG1 0x0664
#define AUX_RX_FILTER_EN BIT(16)
@@ -327,6 +329,18 @@ static int tc_aux_read_data(struct tc_data *tc, void *data, size_t size)
return size;
}
+static u32 tc_auxcfg0(struct drm_dp_aux_msg *msg, size_t size)
+{
+ u32 auxcfg0 = msg->request;
+
+ if (size)
+ auxcfg0 |= FIELD_PREP(DP0_AUXCFG0_BSIZE, size - 1);
+ else
+ auxcfg0 |= DP0_AUXCFG0_ADDR_ONLY;
+
+ return auxcfg0;
+}
+
static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
struct drm_dp_aux_msg *msg)
{
@@ -336,9 +350,6 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
u32 auxstatus;
int ret;
- if (size == 0)
- return 0;
-
ret = tc_aux_wait_busy(tc, 100);
if (ret)
return ret;
@@ -362,8 +373,7 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
if (ret)
return ret;
/* Start transfer */
- ret = regmap_write(tc->regmap, DP0_AUXCFG0,
- ((size - 1) << 8) | request);
+ ret = regmap_write(tc->regmap, DP0_AUXCFG0, tc_auxcfg0(msg, size));
if (ret)
return ret;
@@ -377,8 +387,14 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
if (auxstatus & AUX_TIMEOUT)
return -ETIMEDOUT;
-
- size = FIELD_GET(AUX_BYTES, auxstatus);
+ /*
+ * For some reason address-only DP_AUX_I2C_WRITE (MOT), still
+ * reports 1 byte transferred in its status. To deal we that
+ * we ignore aux_bytes field if we know that this was an
+ * address-only transfer
+ */
+ if (size)
+ size = FIELD_GET(AUX_BYTES, auxstatus);
msg->reply = FIELD_GET(AUX_STATUS, auxstatus);
switch (request) {
--
2.21.0
tc_wait_pll_lock() is always called as a follow-up for updating
PLLUPDATE and PLLEN bit of a given PLL control register. To simplify
things, merge the two operation into a single helper function
tc_pllupdate() and convert the rest of the code to use it. No
functional change intended.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 30 ++++++++++++++----------------
1 file changed, 14 insertions(+), 16 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index ac55b59249e3..28df53f7c349 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -443,10 +443,18 @@ static u32 tc_srcctrl(struct tc_data *tc)
return reg;
}
-static void tc_wait_pll_lock(struct tc_data *tc)
+static int tc_pllupdate(struct tc_data *tc, unsigned int pllctrl)
{
+ int ret;
+
+ ret = regmap_write(tc->regmap, pllctrl, PLLUPDATE | PLLEN);
+ if (ret)
+ return ret;
+
/* Wait for PLL to lock: up to 2.09 ms, depending on refclk */
usleep_range(3000, 6000);
+
+ return 0;
}
static int tc_pxl_pll_en(struct tc_data *tc, u32 refclk, u32 pixelclock)
@@ -546,13 +554,7 @@ static int tc_pxl_pll_en(struct tc_data *tc, u32 refclk, u32 pixelclock)
return ret;
/* Force PLL parameter update and disable bypass */
- ret = regmap_write(tc->regmap, PXL_PLLCTRL, PLLUPDATE | PLLEN);
- if (ret)
- return ret;
-
- tc_wait_pll_lock(tc);
-
- return 0;
+ return tc_pllupdate(tc, PXL_PLLCTRL);
}
static int tc_pxl_pll_dis(struct tc_data *tc)
@@ -626,15 +628,13 @@ static int tc_aux_link_setup(struct tc_data *tc)
* Initially PLLs are in bypass. Force PLL parameter update,
* disable PLL bypass, enable PLL
*/
- ret = regmap_write(tc->regmap, DP0_PLLCTRL, PLLUPDATE | PLLEN);
+ ret = tc_pllupdate(tc, DP0_PLLCTRL);
if (ret)
goto err;
- tc_wait_pll_lock(tc);
- ret = regmap_write(tc->regmap, DP1_PLLCTRL, PLLUPDATE | PLLEN);
+ ret = tc_pllupdate(tc, DP1_PLLCTRL);
if (ret)
goto err;
- tc_wait_pll_lock(tc);
ret = tc_poll_timeout(tc, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 1, 1000);
if (ret == -ETIMEDOUT) {
@@ -914,15 +914,13 @@ static int tc_main_link_enable(struct tc_data *tc)
return ret;
/* PLL setup */
- ret = regmap_write(tc->regmap, DP0_PLLCTRL, PLLUPDATE | PLLEN);
+ ret = tc_pllupdate(tc, DP0_PLLCTRL);
if (ret)
return ret;
- tc_wait_pll_lock(tc);
- ret = regmap_write(tc->regmap, DP1_PLLCTRL, PLLUPDATE | PLLEN);
+ ret = tc_pllupdate(tc, DP1_PLLCTRL);
if (ret)
return ret;
- tc_wait_pll_lock(tc);
/* Reset/Enable Main Links */
dp_phy_ctrl |= DP_PHY_RST | PHY_M1_RST | PHY_M0_RST;
--
2.21.0
According to the datasheet tc358767 can transfer up to 16 bytes via
its AUX channel, so the artificial limit of 8 appears to be too
low. However only up to 15-bytes seem to be actually supported and
trying to use 16-byte transfers results in transfers failing
sporadically (with bogus status in case of I2C transfers), so limit it
to 15.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index e60692b8cd69..8b53dc8908d3 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -354,7 +354,7 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
struct drm_dp_aux_msg *msg)
{
struct tc_data *tc = aux_to_tc(aux);
- size_t size = min_t(size_t, 8, msg->size);
+ size_t size = min_t(size_t, DP_AUX_MAX_PAYLOAD_BYTES - 1, msg->size);
u8 request = msg->request & ~DP_AUX_I2C_MOT;
int ret;
--
2.21.0
Don't assume that requested data transfer size is the same as amount
of data that was transferred. Change the code to get that information
from DP0_AUXSTATUS instead.
Since the check for AUX_BUSY in tc_aux_get_status() is pointless (it
will always called after tc_aux_wait_busy()) and there's only one user
of it, inline its code into tc_aux_transfer() instead of trying to
accommodate the change above.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 40 ++++++++++---------------------
1 file changed, 12 insertions(+), 28 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 8b53dc8908d3..7d0fbb12195b 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -152,10 +152,10 @@
#define DP0_AUXWDATA(i) (0x066c + (i) * 4)
#define DP0_AUXRDATA(i) (0x067c + (i) * 4)
#define DP0_AUXSTATUS 0x068c
-#define AUX_STATUS_MASK 0xf0
-#define AUX_STATUS_SHIFT 4
-#define AUX_TIMEOUT BIT(1)
-#define AUX_BUSY BIT(0)
+#define AUX_BYTES GENMASK(15, 8)
+#define AUX_STATUS GENMASK(7, 4)
+#define AUX_TIMEOUT BIT(1)
+#define AUX_BUSY BIT(0)
#define DP0_AUXI2CADR 0x0698
/* Link Training */
@@ -298,29 +298,6 @@ static int tc_aux_wait_busy(struct tc_data *tc, unsigned int timeout_ms)
1000, 1000 * timeout_ms);
}
-static int tc_aux_get_status(struct tc_data *tc, u8 *reply)
-{
- int ret;
- u32 value;
-
- ret = regmap_read(tc->regmap, DP0_AUXSTATUS, &value);
- if (ret < 0)
- return ret;
-
- if (value & AUX_BUSY) {
- dev_err(tc->dev, "aux busy!\n");
- return -EBUSY;
- }
-
- if (value & AUX_TIMEOUT) {
- dev_err(tc->dev, "aux access timeout!\n");
- return -ETIMEDOUT;
- }
-
- *reply = (value & AUX_STATUS_MASK) >> AUX_STATUS_SHIFT;
- return 0;
-}
-
static int tc_aux_write_data(struct tc_data *tc, const void *data,
size_t size)
{
@@ -356,6 +333,7 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
struct tc_data *tc = aux_to_tc(aux);
size_t size = min_t(size_t, DP_AUX_MAX_PAYLOAD_BYTES - 1, msg->size);
u8 request = msg->request & ~DP_AUX_I2C_MOT;
+ u32 auxstatus;
int ret;
if (size == 0)
@@ -393,10 +371,16 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
if (ret)
return ret;
- ret = tc_aux_get_status(tc, &msg->reply);
+ ret = regmap_read(tc->regmap, DP0_AUXSTATUS, &auxstatus);
if (ret)
return ret;
+ if (auxstatus & AUX_TIMEOUT)
+ return -ETIMEDOUT;
+
+ size = FIELD_GET(AUX_BYTES, auxstatus);
+ msg->reply = FIELD_GET(AUX_STATUS, auxstatus);
+
switch (request) {
case DP_AUX_NATIVE_READ:
case DP_AUX_I2C_READ:
--
2.21.0
Simplify AUX data read by removing index arithmetic and shifting with
a helper function that does two things:
1. Fetch data from up to 4 32-bit registers from the chip
2. Copy read data into user provided array.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 31 ++++++++++++++++++-------------
1 file changed, 18 insertions(+), 13 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 7b15caec2ce5..7152b44db8a3 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -321,6 +321,20 @@ static int tc_aux_get_status(struct tc_data *tc, u8 *reply)
return 0;
}
+static int tc_aux_read_data(struct tc_data *tc, void *data, size_t size)
+{
+ u32 auxrdata[DP_AUX_MAX_PAYLOAD_BYTES / sizeof(u32)];
+ int ret, count = ALIGN(size, sizeof(u32));
+
+ ret = regmap_raw_read(tc->regmap, DP0_AUXRDATA(0), auxrdata, count);
+ if (ret)
+ return ret;
+
+ memcpy(data, auxrdata, size);
+
+ return size;
+}
+
static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
struct drm_dp_aux_msg *msg)
{
@@ -379,19 +393,10 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
if (ret)
return ret;
- if (request == DP_AUX_I2C_READ || request == DP_AUX_NATIVE_READ) {
- /* Read data */
- while (i < size) {
- if ((i % 4) == 0) {
- ret = regmap_read(tc->regmap,
- DP0_AUXRDATA(i >> 2), &tmp);
- if (ret)
- return ret;
- }
- buf[i] = tmp & 0xff;
- tmp = tmp >> 8;
- i++;
- }
+ switch (request) {
+ case DP_AUX_NATIVE_READ:
+ case DP_AUX_I2C_READ:
+ return tc_aux_read_data(tc, msg->buffer, size);
}
return size;
--
2.21.0
A very unfortunate aspect of tc_write()/tc_read() macro helpers is
that they capture quite a bit of context around them and thus require
the caller to have magic variables 'ret' and 'tc' as well as label
'err'. That makes a number of code paths rather counter-intuitive and
somewhat clunky, for example tc_stream_clock_calc() ends up being like
this:
int ret;
tc_write(DP0_VIDMNGEN1, 32768);
return 0;
err:
return ret;
which is rather surprising when you read the code for the first
time. Since those helpers arguably aren't really saving that much code
and there's no way of fixing them without making them too verbose to
be worth it change the driver code to not use them at all.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 382 ++++++++++++++++++------------
1 file changed, 230 insertions(+), 152 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 5b78021d6c5b..7b15caec2ce5 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -280,20 +280,6 @@ static inline struct tc_data *connector_to_tc(struct drm_connector *c)
return container_of(c, struct tc_data, connector);
}
-/* Simple macros to avoid repeated error checks */
-#define tc_write(reg, var) \
- do { \
- ret = regmap_write(tc->regmap, reg, var); \
- if (ret) \
- goto err; \
- } while (0)
-#define tc_read(reg, var) \
- do { \
- ret = regmap_read(tc->regmap, reg, var); \
- if (ret) \
- goto err; \
- } while (0)
-
static inline int tc_poll_timeout(struct tc_data *tc, unsigned int addr,
unsigned int cond_mask,
unsigned int cond_value,
@@ -351,7 +337,7 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
ret = tc_aux_wait_busy(tc, 100);
if (ret)
- goto err;
+ return ret;
if (request == DP_AUX_I2C_WRITE || request == DP_AUX_NATIVE_WRITE) {
/* Store data */
@@ -362,7 +348,11 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
tmp = (tmp << 8) | buf[i];
i++;
if (((i % 4) == 0) || (i == size)) {
- tc_write(DP0_AUXWDATA((i - 1) >> 2), tmp);
+ ret = regmap_write(tc->regmap,
+ DP0_AUXWDATA((i - 1) >> 2),
+ tmp);
+ if (ret)
+ return ret;
tmp = 0;
}
}
@@ -372,23 +362,32 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
}
/* Store address */
- tc_write(DP0_AUXADDR, msg->address);
+ ret = regmap_write(tc->regmap, DP0_AUXADDR, msg->address);
+ if (ret)
+ return ret;
/* Start transfer */
- tc_write(DP0_AUXCFG0, ((size - 1) << 8) | request);
+ ret = regmap_write(tc->regmap, DP0_AUXCFG0,
+ ((size - 1) << 8) | request);
+ if (ret)
+ return ret;
ret = tc_aux_wait_busy(tc, 100);
if (ret)
- goto err;
+ return ret;
ret = tc_aux_get_status(tc, &msg->reply);
if (ret)
- goto err;
+ return ret;
if (request == DP_AUX_I2C_READ || request == DP_AUX_NATIVE_READ) {
/* Read data */
while (i < size) {
- if ((i % 4) == 0)
- tc_read(DP0_AUXRDATA(i >> 2), &tmp);
+ if ((i % 4) == 0) {
+ ret = regmap_read(tc->regmap,
+ DP0_AUXRDATA(i >> 2), &tmp);
+ if (ret)
+ return ret;
+ }
buf[i] = tmp & 0xff;
tmp = tmp >> 8;
i++;
@@ -396,8 +395,6 @@ static ssize_t tc_aux_transfer(struct drm_dp_aux *aux,
}
return size;
-err:
- return ret;
}
static const char * const training_pattern1_errors[] = {
@@ -454,6 +451,7 @@ static int tc_pxl_pll_en(struct tc_data *tc, u32 refclk, u32 pixelclock)
int ext_div[] = {1, 2, 3, 5, 7};
int best_pixelclock = 0;
int vco_hi = 0;
+ u32 pxl_pllparam;
dev_dbg(tc->dev, "PLL: requested %d pixelclock, ref %d\n", pixelclock,
refclk);
@@ -523,24 +521,29 @@ static int tc_pxl_pll_en(struct tc_data *tc, u32 refclk, u32 pixelclock)
best_mul = 0;
/* Power up PLL and switch to bypass */
- tc_write(PXL_PLLCTRL, PLLBYP | PLLEN);
+ ret = regmap_write(tc->regmap, PXL_PLLCTRL, PLLBYP | PLLEN);
+ if (ret)
+ return ret;
+
+ pxl_pllparam = vco_hi << 24; /* For PLL VCO >= 300 MHz = 1 */
+ pxl_pllparam |= ext_div[best_pre] << 20; /* External Pre-divider */
+ pxl_pllparam |= ext_div[best_post] << 16; /* External Post-divider */
+ pxl_pllparam |= IN_SEL_REFCLK; /* Use RefClk as PLL input */
+ pxl_pllparam |= best_div << 8; /* Divider for PLL RefClk */
+ pxl_pllparam |= best_mul; /* Multiplier for PLL */
- tc_write(PXL_PLLPARAM,
- (vco_hi << 24) | /* For PLL VCO >= 300 MHz = 1 */
- (ext_div[best_pre] << 20) | /* External Pre-divider */
- (ext_div[best_post] << 16) | /* External Post-divider */
- IN_SEL_REFCLK | /* Use RefClk as PLL input */
- (best_div << 8) | /* Divider for PLL RefClk */
- (best_mul << 0)); /* Multiplier for PLL */
+ ret = regmap_write(tc->regmap, PXL_PLLPARAM, pxl_pllparam);
+ if (ret)
+ return ret;
/* Force PLL parameter update and disable bypass */
- tc_write(PXL_PLLCTRL, PLLUPDATE | PLLEN);
+ ret = regmap_write(tc->regmap, PXL_PLLCTRL, PLLUPDATE | PLLEN);
+ if (ret)
+ return ret;
tc_wait_pll_lock(tc);
return 0;
-err:
- return ret;
}
static int tc_pxl_pll_dis(struct tc_data *tc)
@@ -551,7 +554,6 @@ static int tc_pxl_pll_dis(struct tc_data *tc)
static int tc_stream_clock_calc(struct tc_data *tc)
{
- int ret;
/*
* If the Stream clock and Link Symbol clock are
* asynchronous with each other, the value of M changes over
@@ -567,16 +569,13 @@ static int tc_stream_clock_calc(struct tc_data *tc)
* M/N = f_STRMCLK / f_LSCLK
*
*/
- tc_write(DP0_VIDMNGEN1, 32768);
-
- return 0;
-err:
- return ret;
+ return regmap_write(tc->regmap, DP0_VIDMNGEN1, 32768);
}
static int tc_aux_link_setup(struct tc_data *tc)
{
unsigned long rate;
+ u32 dp0_auxcfg1;
u32 value;
int ret;
@@ -601,18 +600,26 @@ static int tc_aux_link_setup(struct tc_data *tc)
/* Setup DP-PHY / PLL */
value |= SYSCLK_SEL_LSCLK | LSCLK_DIV_2;
- tc_write(SYS_PLLPARAM, value);
-
- tc_write(DP_PHY_CTRL, BGREN | PWR_SW_EN | PHY_A0_EN);
+ ret = regmap_write(tc->regmap, SYS_PLLPARAM, value);
+ if (ret)
+ goto err;
+ ret = regmap_write(tc->regmap, DP_PHY_CTRL,
+ BGREN | PWR_SW_EN | PHY_A0_EN);
+ if (ret)
+ goto err;
/*
* Initially PLLs are in bypass. Force PLL parameter update,
* disable PLL bypass, enable PLL
*/
- tc_write(DP0_PLLCTRL, PLLUPDATE | PLLEN);
+ ret = regmap_write(tc->regmap, DP0_PLLCTRL, PLLUPDATE | PLLEN);
+ if (ret)
+ goto err;
tc_wait_pll_lock(tc);
- tc_write(DP1_PLLCTRL, PLLUPDATE | PLLEN);
+ ret = regmap_write(tc->regmap, DP1_PLLCTRL, PLLUPDATE | PLLEN);
+ if (ret)
+ goto err;
tc_wait_pll_lock(tc);
ret = tc_poll_timeout(tc, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 1, 1000);
@@ -624,9 +631,13 @@ static int tc_aux_link_setup(struct tc_data *tc)
}
/* Setup AUX link */
- tc_write(DP0_AUXCFG1, AUX_RX_FILTER_EN |
- (0x06 << 8) | /* Aux Bit Period Calculator Threshold */
- (0x3f << 0)); /* Aux Response Timeout Timer */
+ dp0_auxcfg1 = AUX_RX_FILTER_EN;
+ dp0_auxcfg1 |= 0x06 << 8; /* Aux Bit Period Calculator Threshold */
+ dp0_auxcfg1 |= 0x3f << 0; /* Aux Response Timeout Timer */
+
+ ret = regmap_write(tc->regmap, DP0_AUXCFG1, dp0_auxcfg1);
+ if (ret)
+ goto err;
return 0;
err:
@@ -727,48 +738,73 @@ static int tc_set_video_mode(struct tc_data *tc,
* assume we do not need any delay when DPI is a source of
* sync signals
*/
- tc_write(VPCTRL0,
- FIELD_PREP(VSDELAY, 0) |
- OPXLFMT_RGB888 | FRMSYNC_DISABLED | MSF_DISABLED);
- tc_write(HTIM01,
- FIELD_PREP(HBPR, ALIGN(left_margin, 2)) |
- FIELD_PREP(HPW, ALIGN(hsync_len, 2)));
- tc_write(HTIM02,
- FIELD_PREP(HDISPR, ALIGN(mode->hdisplay, 2)) |
- FIELD_PREP(HFPR, ALIGN(right_margin, 2)));
- tc_write(VTIM01,
- FIELD_PREP(VBPR, upper_margin) |
- FIELD_PREP(VSPR, vsync_len));
- tc_write(VTIM02,
- FIELD_PREP(VFPR, lower_margin) |
- FIELD_PREP(VDISPR, mode->vdisplay));
- tc_write(VFUEN0, VFUEN); /* update settings */
+ ret = regmap_write(tc->regmap, VPCTRL0,
+ FIELD_PREP(VSDELAY, 0) |
+ OPXLFMT_RGB888 | FRMSYNC_DISABLED | MSF_DISABLED);
+ if (ret)
+ return ret;
+
+ ret = regmap_write(tc->regmap, HTIM01,
+ FIELD_PREP(HBPR, ALIGN(left_margin, 2)) |
+ FIELD_PREP(HPW, ALIGN(hsync_len, 2)));
+ if (ret)
+ return ret;
+
+ ret = regmap_write(tc->regmap, HTIM02,
+ FIELD_PREP(HDISPR, ALIGN(mode->hdisplay, 2)) |
+ FIELD_PREP(HFPR, ALIGN(right_margin, 2)));
+ if (ret)
+ return ret;
+
+ ret = regmap_write(tc->regmap, VTIM01,
+ FIELD_PREP(VBPR, upper_margin) |
+ FIELD_PREP(VSPR, vsync_len));
+ if (ret)
+ return ret;
+
+ ret = regmap_write(tc->regmap, VTIM02,
+ FIELD_PREP(VFPR, lower_margin) |
+ FIELD_PREP(VDISPR, mode->vdisplay));
+ if (ret)
+ return ret;
+
+ ret = regmap_write(tc->regmap, VFUEN0, VFUEN); /* update settings */
+ if (ret)
+ return ret;
/* Test pattern settings */
- tc_write(TSTCTL,
- FIELD_PREP(COLOR_R, 120) |
- FIELD_PREP(COLOR_G, 20) |
- FIELD_PREP(COLOR_B, 99) |
- ENI2CFILTER |
- FIELD_PREP(COLOR_BAR_MODE, COLOR_BAR_MODE_BARS));
+ ret = regmap_write(tc->regmap, TSTCTL,
+ FIELD_PREP(COLOR_R, 120) |
+ FIELD_PREP(COLOR_G, 20) |
+ FIELD_PREP(COLOR_B, 99) |
+ ENI2CFILTER |
+ FIELD_PREP(COLOR_BAR_MODE, COLOR_BAR_MODE_BARS));
+ if (ret)
+ return ret;
/* DP Main Stream Attributes */
vid_sync_dly = hsync_len + left_margin + mode->hdisplay;
- tc_write(DP0_VIDSYNCDELAY,
+ ret = regmap_write(tc->regmap, DP0_VIDSYNCDELAY,
FIELD_PREP(THRESH_DLY, max_tu_symbol) |
FIELD_PREP(VID_SYNC_DLY, vid_sync_dly));
- tc_write(DP0_TOTALVAL,
- FIELD_PREP(H_TOTAL, mode->htotal) |
- FIELD_PREP(V_TOTAL, mode->vtotal));
+ ret = regmap_write(tc->regmap, DP0_TOTALVAL,
+ FIELD_PREP(H_TOTAL, mode->htotal) |
+ FIELD_PREP(V_TOTAL, mode->vtotal));
+ if (ret)
+ return ret;
- tc_write(DP0_STARTVAL,
- FIELD_PREP(H_START, left_margin + hsync_len) |
- FIELD_PREP(V_START, upper_margin + vsync_len));
+ ret = regmap_write(tc->regmap, DP0_STARTVAL,
+ FIELD_PREP(H_START, left_margin + hsync_len) |
+ FIELD_PREP(V_START, upper_margin + vsync_len));
+ if (ret)
+ return ret;
- tc_write(DP0_ACTIVEVAL,
- FIELD_PREP(V_ACT, mode->vdisplay) |
- FIELD_PREP(H_ACT, mode->hdisplay));
+ ret = regmap_write(tc->regmap, DP0_ACTIVEVAL,
+ FIELD_PREP(V_ACT, mode->vdisplay) |
+ FIELD_PREP(H_ACT, mode->hdisplay));
+ if (ret)
+ return ret;
dp0_syncval = FIELD_PREP(VS_WIDTH, vsync_len) |
FIELD_PREP(HS_WIDTH, hsync_len);
@@ -779,21 +815,25 @@ static int tc_set_video_mode(struct tc_data *tc,
if (mode->flags & DRM_MODE_FLAG_NHSYNC)
dp0_syncval |= SYNCVAL_HS_POL_ACTIVE_LOW;
- tc_write(DP0_SYNCVAL, dp0_syncval);
+ ret = regmap_write(tc->regmap, DP0_SYNCVAL, dp0_syncval);
+ if (ret)
+ return ret;
- tc_write(DPIPXLFMT,
- VS_POL_ACTIVE_LOW | HS_POL_ACTIVE_LOW |
- DE_POL_ACTIVE_HIGH | SUB_CFG_TYPE_CONFIG1 |
- DPI_BPP_RGB888);
+ ret = regmap_write(tc->regmap, DPIPXLFMT,
+ VS_POL_ACTIVE_LOW | HS_POL_ACTIVE_LOW |
+ DE_POL_ACTIVE_HIGH | SUB_CFG_TYPE_CONFIG1 |
+ DPI_BPP_RGB888);
+ if (ret)
+ return ret;
- tc_write(DP0_MISC,
- FIELD_PREP(MAX_TU_SYMBOL, max_tu_symbol) |
- FIELD_PREP(TU_SIZE, TU_SIZE_RECOMMENDED) |
- BPC_8);
+ ret = regmap_write(tc->regmap, DP0_MISC,
+ FIELD_PREP(MAX_TU_SYMBOL, max_tu_symbol) |
+ FIELD_PREP(TU_SIZE, TU_SIZE_RECOMMENDED) |
+ BPC_8);
+ if (ret)
+ return ret;
return 0;
-err:
- return ret;
}
static int tc_wait_link_training(struct tc_data *tc)
@@ -808,11 +848,11 @@ static int tc_wait_link_training(struct tc_data *tc)
return ret;
}
- tc_read(DP0_LTSTAT, &value);
+ ret = regmap_read(tc->regmap, DP0_LTSTAT, &value);
+ if (ret)
+ return ret;
return (value >> 8) & 0x7;
-err:
- return ret;
}
static int tc_main_link_enable(struct tc_data *tc)
@@ -827,15 +867,25 @@ static int tc_main_link_enable(struct tc_data *tc)
dev_dbg(tc->dev, "link enable\n");
- tc_read(DP0CTL, &value);
- if (WARN_ON(value & DP_EN))
- tc_write(DP0CTL, 0);
+ ret = regmap_read(tc->regmap, DP0CTL, &value);
+ if (ret)
+ return ret;
+
+ if (WARN_ON(value & DP_EN)) {
+ ret = regmap_write(tc->regmap, DP0CTL, 0);
+ if (ret)
+ return ret;
+ }
- tc_write(DP0_SRCCTRL, tc_srcctrl(tc));
+ ret = regmap_write(tc->regmap, DP0_SRCCTRL, tc_srcctrl(tc));
+ if (ret)
+ return ret;
/* SSCG and BW27 on DP1 must be set to the same as on DP0 */
- tc_write(DP1_SRCCTRL,
+ ret = regmap_write(tc->regmap, DP1_SRCCTRL,
(tc->link.spread ? DP0_SRCCTRL_SSCG : 0) |
((tc->link.base.rate != 162000) ? DP0_SRCCTRL_BW27 : 0));
+ if (ret)
+ return ret;
rate = clk_get_rate(tc->refclk);
switch (rate) {
@@ -855,27 +905,36 @@ static int tc_main_link_enable(struct tc_data *tc)
return -EINVAL;
}
value |= SYSCLK_SEL_LSCLK | LSCLK_DIV_2;
- tc_write(SYS_PLLPARAM, value);
+ ret = regmap_write(tc->regmap, SYS_PLLPARAM, value);
+ if (ret)
+ return ret;
/* Setup Main Link */
dp_phy_ctrl = BGREN | PWR_SW_EN | PHY_A0_EN | PHY_M0_EN;
if (tc->link.base.num_lanes == 2)
dp_phy_ctrl |= PHY_2LANE;
- tc_write(DP_PHY_CTRL, dp_phy_ctrl);
+
+ ret = regmap_write(tc->regmap, DP_PHY_CTRL, dp_phy_ctrl);
+ if (ret)
+ return ret;
/* PLL setup */
- tc_write(DP0_PLLCTRL, PLLUPDATE | PLLEN);
+ ret = regmap_write(tc->regmap, DP0_PLLCTRL, PLLUPDATE | PLLEN);
+ if (ret)
+ return ret;
tc_wait_pll_lock(tc);
- tc_write(DP1_PLLCTRL, PLLUPDATE | PLLEN);
+ ret = regmap_write(tc->regmap, DP1_PLLCTRL, PLLUPDATE | PLLEN);
+ if (ret)
+ return ret;
tc_wait_pll_lock(tc);
/* Reset/Enable Main Links */
dp_phy_ctrl |= DP_PHY_RST | PHY_M1_RST | PHY_M0_RST;
- tc_write(DP_PHY_CTRL, dp_phy_ctrl);
+ ret = regmap_write(tc->regmap, DP_PHY_CTRL, dp_phy_ctrl);
usleep_range(100, 200);
dp_phy_ctrl &= ~(DP_PHY_RST | PHY_M1_RST | PHY_M0_RST);
- tc_write(DP_PHY_CTRL, dp_phy_ctrl);
+ ret = regmap_write(tc->regmap, DP_PHY_CTRL, dp_phy_ctrl);
ret = tc_poll_timeout(tc, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 1, 1000);
if (ret) {
@@ -886,7 +945,7 @@ static int tc_main_link_enable(struct tc_data *tc)
/* Set misc: 8 bits per color */
ret = regmap_update_bits(tc->regmap, DP0_MISC, BPC_8, BPC_8);
if (ret)
- goto err;
+ return ret;
/*
* ASSR mode
@@ -939,53 +998,71 @@ static int tc_main_link_enable(struct tc_data *tc)
/* Clock-Recovery */
/* Set DPCD 0x102 for Training Pattern 1 */
- tc_write(DP0_SNKLTCTRL, DP_LINK_SCRAMBLING_DISABLE |
- DP_TRAINING_PATTERN_1);
+ ret = regmap_write(tc->regmap, DP0_SNKLTCTRL,
+ DP_LINK_SCRAMBLING_DISABLE |
+ DP_TRAINING_PATTERN_1);
+ if (ret)
+ return ret;
- tc_write(DP0_LTLOOPCTRL,
- (15 << 28) | /* Defer Iteration Count */
- (15 << 24) | /* Loop Iteration Count */
- (0xd << 0)); /* Loop Timer Delay */
+ ret = regmap_write(tc->regmap, DP0_LTLOOPCTRL,
+ (15 << 28) | /* Defer Iteration Count */
+ (15 << 24) | /* Loop Iteration Count */
+ (0xd << 0)); /* Loop Timer Delay */
+ if (ret)
+ return ret;
- tc_write(DP0_SRCCTRL, tc_srcctrl(tc) | DP0_SRCCTRL_SCRMBLDIS |
- DP0_SRCCTRL_AUTOCORRECT | DP0_SRCCTRL_TP1);
+ ret = regmap_write(tc->regmap, DP0_SRCCTRL,
+ tc_srcctrl(tc) | DP0_SRCCTRL_SCRMBLDIS |
+ DP0_SRCCTRL_AUTOCORRECT |
+ DP0_SRCCTRL_TP1);
+ if (ret)
+ return ret;
/* Enable DP0 to start Link Training */
- tc_write(DP0CTL,
- ((tc->link.base.capabilities & DP_LINK_CAP_ENHANCED_FRAMING) ? EF_EN : 0) |
- DP_EN);
+ ret = regmap_write(tc->regmap, DP0CTL,
+ ((tc->link.base.capabilities &
+ DP_LINK_CAP_ENHANCED_FRAMING) ? EF_EN : 0) |
+ DP_EN);
+ if (ret)
+ return ret;
/* wait */
+
ret = tc_wait_link_training(tc);
if (ret < 0)
- goto err;
+ return ret;
if (ret) {
dev_err(tc->dev, "Link training phase 1 failed: %s\n",
training_pattern1_errors[ret]);
- ret = -ENODEV;
- goto err;
+ return -ENODEV;
}
/* Channel Equalization */
/* Set DPCD 0x102 for Training Pattern 2 */
- tc_write(DP0_SNKLTCTRL, DP_LINK_SCRAMBLING_DISABLE |
- DP_TRAINING_PATTERN_2);
+ ret = regmap_write(tc->regmap, DP0_SNKLTCTRL,
+ DP_LINK_SCRAMBLING_DISABLE |
+ DP_TRAINING_PATTERN_2);
+ if (ret)
+ return ret;
- tc_write(DP0_SRCCTRL, tc_srcctrl(tc) | DP0_SRCCTRL_SCRMBLDIS |
- DP0_SRCCTRL_AUTOCORRECT | DP0_SRCCTRL_TP2);
+ ret = regmap_write(tc->regmap, DP0_SRCCTRL,
+ tc_srcctrl(tc) | DP0_SRCCTRL_SCRMBLDIS |
+ DP0_SRCCTRL_AUTOCORRECT |
+ DP0_SRCCTRL_TP2);
+ if (ret)
+ return ret;
/* wait */
ret = tc_wait_link_training(tc);
if (ret < 0)
- goto err;
+ return ret;
if (ret) {
dev_err(tc->dev, "Link training phase 2 failed: %s\n",
training_pattern2_errors[ret]);
- ret = -ENODEV;
- goto err;
+ return -ENODEV;
}
/*
@@ -998,7 +1075,10 @@ static int tc_main_link_enable(struct tc_data *tc)
*/
/* Clear Training Pattern, set AutoCorrect Mode = 1 */
- tc_write(DP0_SRCCTRL, tc_srcctrl(tc) | DP0_SRCCTRL_AUTOCORRECT);
+ ret = regmap_write(tc->regmap, DP0_SRCCTRL, tc_srcctrl(tc) |
+ DP0_SRCCTRL_AUTOCORRECT);
+ if (ret)
+ return ret;
/* Clear DPCD 0x102 */
/* Note: Can Not use DP0_SNKLTCTRL (0x06E4) short cut */
@@ -1042,7 +1122,7 @@ static int tc_main_link_enable(struct tc_data *tc)
dev_err(dev, "0x0205 SINK_STATUS: 0x%02x\n", tmp[3]);
dev_err(dev, "0x0206 ADJUST_REQUEST_LANE0_1: 0x%02x\n", tmp[4]);
dev_err(dev, "0x0207 ADJUST_REQUEST_LANE2_3: 0x%02x\n", tmp[5]);
- goto err;
+ return ret;
}
return 0;
@@ -1051,7 +1131,6 @@ static int tc_main_link_enable(struct tc_data *tc)
return ret;
err_dpcd_write:
dev_err(tc->dev, "Failed to write DPCD: %d\n", ret);
-err:
return ret;
}
@@ -1061,12 +1140,11 @@ static int tc_main_link_disable(struct tc_data *tc)
dev_dbg(tc->dev, "link disable\n");
- tc_write(DP0_SRCCTRL, 0);
- tc_write(DP0CTL, 0);
+ ret = regmap_write(tc->regmap, DP0_SRCCTRL, 0);
+ if (ret)
+ return ret;
- return 0;
-err:
- return ret;
+ return regmap_write(tc->regmap, DP0CTL, 0);
}
static int tc_stream_enable(struct tc_data *tc)
@@ -1081,7 +1159,7 @@ static int tc_stream_enable(struct tc_data *tc)
ret = tc_pxl_pll_en(tc, clk_get_rate(tc->refclk),
1000 * tc->mode.clock);
if (ret)
- goto err;
+ return ret;
}
ret = tc_set_video_mode(tc, &tc->mode);
@@ -1096,7 +1174,9 @@ static int tc_stream_enable(struct tc_data *tc)
value = VID_MN_GEN | DP_EN;
if (tc->link.base.capabilities & DP_LINK_CAP_ENHANCED_FRAMING)
value |= EF_EN;
- tc_write(DP0CTL, value);
+ ret = regmap_write(tc->regmap, DP0CTL, value);
+ if (ret)
+ return ret;
/*
* VID_EN assertion should be delayed by at least N * LSCLK
* cycles from the time VID_MN_GEN is enabled in order to
@@ -1106,36 +1186,35 @@ static int tc_stream_enable(struct tc_data *tc)
*/
usleep_range(500, 1000);
value |= VID_EN;
- tc_write(DP0CTL, value);
+ ret = regmap_write(tc->regmap, DP0CTL, value);
+ if (ret)
+ return ret;
/* Set input interface */
value = DP0_AUDSRC_NO_INPUT;
if (tc_test_pattern)
value |= DP0_VIDSRC_COLOR_BAR;
else
value |= DP0_VIDSRC_DPI_RX;
- tc_write(SYSCTRL, value);
+ ret = regmap_write(tc->regmap, SYSCTRL, value);
+ if (ret)
+ return ret;
return 0;
-err:
- return ret;
}
static int tc_stream_disable(struct tc_data *tc)
{
int ret;
- u32 val;
dev_dbg(tc->dev, "disable video stream\n");
- tc_read(DP0CTL, &val);
- val &= ~VID_EN;
- tc_write(DP0CTL, val);
+ ret = regmap_update_bits(tc->regmap, DP0CTL, VID_EN, 0);
+ if (ret)
+ return ret;
tc_pxl_pll_dis(tc);
return 0;
-err:
- return ret;
}
static void tc_bridge_pre_enable(struct drm_bridge *bridge)
@@ -1327,7 +1406,9 @@ static enum drm_connector_status tc_connector_detect(struct drm_connector *conne
return connector_status_unknown;
}
- tc_read(GPIOI, &val);
+ ret = regmap_read(tc->regmap, GPIOI, &val);
+ if (ret)
+ return connector_status_unknown;
conn = val & BIT(tc->hpd_pin);
@@ -1335,9 +1416,6 @@ static enum drm_connector_status tc_connector_detect(struct drm_connector *conne
return connector_status_connected;
else
return connector_status_disconnected;
-
-err:
- return connector_status_unknown;
}
static const struct drm_connector_funcs tc_connector_funcs = {
--
2.21.0
Implementation of tc_poll_timeout() is almost a 100% copy-and-paste of
the code for regmap_read_poll_timeout(). Replace copied code with a
call to the original. While at it change tc_poll_timeout to accept
"struct tc_data *" instead of "struct regmap *" for brevity. No
functional change intended.
Signed-off-by: Andrey Smirnov <[email protected]>
Reviewed-by: Andrzej Hajda <[email protected]>
Reviewed-by: Laurent Pinchart <[email protected]>
Cc: Andrzej Hajda <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Cc: Andrey Gusakov <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Cory Tusar <[email protected]>
Cc: Chris Healy <[email protected]>
Cc: Lucas Stach <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
drivers/gpu/drm/bridge/tc358767.c | 26 ++++++--------------------
1 file changed, 6 insertions(+), 20 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 58e3ca0e25af..fb8a1942ec54 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -264,34 +264,21 @@ static inline struct tc_data *connector_to_tc(struct drm_connector *c)
goto err; \
} while (0)
-static inline int tc_poll_timeout(struct regmap *map, unsigned int addr,
+static inline int tc_poll_timeout(struct tc_data *tc, unsigned int addr,
unsigned int cond_mask,
unsigned int cond_value,
unsigned long sleep_us, u64 timeout_us)
{
- ktime_t timeout = ktime_add_us(ktime_get(), timeout_us);
unsigned int val;
- int ret;
- for (;;) {
- ret = regmap_read(map, addr, &val);
- if (ret)
- break;
- if ((val & cond_mask) == cond_value)
- break;
- if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) {
- ret = regmap_read(map, addr, &val);
- break;
- }
- if (sleep_us)
- usleep_range((sleep_us >> 2) + 1, sleep_us);
- }
- return ret ?: (((val & cond_mask) == cond_value) ? 0 : -ETIMEDOUT);
+ return regmap_read_poll_timeout(tc->regmap, addr, val,
+ (val & cond_mask) == cond_value,
+ sleep_us, timeout_us);
}
static int tc_aux_wait_busy(struct tc_data *tc, unsigned int timeout_ms)
{
- return tc_poll_timeout(tc->regmap, DP0_AUXSTATUS, AUX_BUSY, 0,
+ return tc_poll_timeout(tc, DP0_AUXSTATUS, AUX_BUSY, 0,
1000, 1000 * timeout_ms);
}
@@ -598,8 +585,7 @@ static int tc_aux_link_setup(struct tc_data *tc)
tc_write(DP1_PLLCTRL, PLLUPDATE | PLLEN);
tc_wait_pll_lock(tc);
- ret = tc_poll_timeout(tc->regmap, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 1,
- 1000);
+ ret = tc_poll_timeout(tc, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 1, 1000);
if (ret == -ETIMEDOUT) {
dev_err(tc->dev, "Timeout waiting for PHY to become ready");
return ret;
--
2.21.0
On 12.06.2019 10:32, Andrey Smirnov wrote:
> Everyone:
>
> This series contains various improvements (at least in my mind) and
> fixes that I made to tc358767 while working with the code of the
> driver. Hopefuly each patch is self explanatory.
>
> Feedback is welcome!
>
> Thanks,
> Andrey Smirnov
Tomi, you can queue it to drm-misc-next.
Regards
Andrzej
>
> Changes since [v4]:
>
> - tc_pllupdate_pllen() renamed to tc_pllupdate()
>
> - Collected Reviewed-bys from Andrzej for the rest of the series
>
> Changes since [v3]:
>
> - Collected Reviewed-bys from Andrzej
>
> - Dropped explicit check for -ETIMEDOUT in "drm/bridge: tc358767:
> Simplify polling in tc_main_link_setup()" for consistency
>
> - AUX transfer code converted to user regmap_raw_read(),
> regmap_raw_write()
>
> Changes since [v2]:
>
> - Patchset rebased on top of v4 of Tomi's series that recently
> went in (https://patchwork.freedesktop.org/series/58176/#rev5)
>
> - AUX transfer code converted to user regmap_bulk_read(),
> regmap_bulk_write()
>
> Changes since [v1]:
>
> - Patchset rebased on top of
> https://patchwork.freedesktop.org/series/58176/
>
> - Patches to remove both tc_write() and tc_read() helpers added
>
> - Patches to rework AUX transfer code added
>
> - Both "drm/bridge: tc358767: Simplify polling in
> tc_main_link_setup()" and "drm/bridge: tc358767: Simplify
> polling in tc_link_training()" changed to use tc_poll_timeout()
> instead of regmap_read_poll_timeout()
>
> [v4] lkml.kernel.org/r/[email protected]
> [v3] lkml.kernel.org/r/[email protected]
> [v2] lkml.kernel.org/r/[email protected]
> [v1] lkml.kernel.org/r/[email protected]
>
> Andrey Smirnov (15):
> drm/bridge: tc358767: Simplify tc_poll_timeout()
> drm/bridge: tc358767: Simplify polling in tc_main_link_setup()
> drm/bridge: tc358767: Simplify polling in tc_link_training()
> drm/bridge: tc358767: Simplify tc_set_video_mode()
> drm/bridge: tc358767: Drop custom tc_write()/tc_read() accessors
> drm/bridge: tc358767: Simplify AUX data read
> drm/bridge: tc358767: Simplify AUX data write
> drm/bridge: tc358767: Increase AUX transfer length limit
> drm/bridge: tc358767: Use reported AUX transfer size
> drm/bridge: tc358767: Add support for address-only I2C transfers
> drm/bridge: tc358767: Introduce tc_set_syspllparam()
> drm/bridge: tc358767: Introduce tc_pllupdate()
> drm/bridge: tc358767: Simplify tc_aux_wait_busy()
> drm/bridge: tc358767: Drop unnecessary 8 byte buffer
> drm/bridge: tc358767: Replace magic number in tc_main_link_enable()
>
> drivers/gpu/drm/bridge/tc358767.c | 648 +++++++++++++++++-------------
> 1 file changed, 372 insertions(+), 276 deletions(-)
>
Hi,
On 12/06/2019 11:32, Andrey Smirnov wrote:
> Everyone:
>
> This series contains various improvements (at least in my mind) and
> fixes that I made to tc358767 while working with the code of the
> driver. Hopefuly each patch is self explanatory.
I haven't had time to debug, but I did a quick test with the series, and
EDID read no longer works on my setup. drm_get_edid() returns 0. I need
to dig in further.
Tomi
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Hi,
On 12/06/2019 11:32, Andrey Smirnov wrote:
> Transfer size of zero means a request to do an address-only
> transfer. Since the HW support this, we probably shouldn't be just
> ignoring such requests. While at it allow DP_AUX_I2C_MOT flag to pass
> through, since it is supported by the HW as well.
I bisected the EDID read issue to this patch...
Tomi
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
On Wed, Jun 12, 2019 at 5:48 AM Tomi Valkeinen <[email protected]> wrote:
>
> Hi,
>
> On 12/06/2019 11:32, Andrey Smirnov wrote:
> > Transfer size of zero means a request to do an address-only
> > transfer. Since the HW support this, we probably shouldn't be just
> > ignoring such requests. While at it allow DP_AUX_I2C_MOT flag to pass
> > through, since it is supported by the HW as well.
>
> I bisected the EDID read issue to this patch...
>
I don't think I've had any problems on my end with this. I'll double
check. It might be the case that yours is the only setup where the
problem can be repro'd, though. We can drop this patch if you don't
have time/would rather not dig into this.
Thanks,
Andrey Smirnov
On Wed, Jun 12, 2019 at 9:22 AM Andrey Smirnov <[email protected]> wrote:
>
> On Wed, Jun 12, 2019 at 5:48 AM Tomi Valkeinen <[email protected]> wrote:
> >
> > Hi,
> >
> > On 12/06/2019 11:32, Andrey Smirnov wrote:
> > > Transfer size of zero means a request to do an address-only
> > > transfer. Since the HW support this, we probably shouldn't be just
> > > ignoring such requests. While at it allow DP_AUX_I2C_MOT flag to pass
> > > through, since it is supported by the HW as well.
> >
> > I bisected the EDID read issue to this patch...
> >
>
> I don't think I've had any problems on my end with this. I'll double
> check. It might be the case that yours is the only setup where the
> problem can be repro'd, though. We can drop this patch if you don't
> have time/would rather not dig into this.
>
Turns out I do have this problem. Just didn't pay enough attention to
notice. Will fix in v6.
Thanks,
Andrey Smirnov