Hi,
This patch series adds initial support for the Microsemi MIPS SoCs. It
is currently focusing on the Microsemi Ocelot (VSC7513, VSC7514).
Changes in v5:
- reworked the DT to remove ocelot_measure_hpt_freq()
- fixed the memory node (memory@0)
- fixed indentation
- board-ocelot.config:
o require CONFIG_CPU_MIPS32_R2
o removed CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER
o removed CONFIG_SQUASHFS because generic_defconfig has
# CONFIG_MISC_FILESYSTEMS is not set
- removed DMA_NONCOHERENT from MSCC_OCELOT
Alexandre Belloni (5):
dt-bindings: mips: Add bindings for Microsemi SoCs
MIPS: mscc: add ocelot dtsi
MIPS: mscc: add ocelot PCB123 device tree
MIPS: generic: Add support for Microsemi Ocelot
MAINTAINERS: Add entry for Microsemi MIPS SoCs
Documentation/devicetree/bindings/mips/mscc.txt | 43 +++++++++
MAINTAINERS | 9 ++
arch/mips/Makefile | 4 +
arch/mips/boot/dts/Makefile | 1 +
arch/mips/boot/dts/mscc/Makefile | 3 +
arch/mips/boot/dts/mscc/ocelot.dtsi | 117 ++++++++++++++++++++++++
arch/mips/boot/dts/mscc/ocelot_pcb123.dts | 27 ++++++
arch/mips/configs/generic/board-ocelot.config | 36 ++++++++
arch/mips/generic/Kconfig | 16 ++++
arch/mips/generic/Makefile | 1 +
arch/mips/generic/board-ocelot.c | 67 ++++++++++++++
11 files changed, 324 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mips/mscc.txt
create mode 100644 arch/mips/boot/dts/mscc/Makefile
create mode 100644 arch/mips/boot/dts/mscc/ocelot.dtsi
create mode 100644 arch/mips/boot/dts/mscc/ocelot_pcb123.dts
create mode 100644 arch/mips/configs/generic/board-ocelot.config
create mode 100644 arch/mips/generic/board-ocelot.c
--
2.16.2
Add bindings for Microsemi SoCs. Currently only Ocelot is supported.
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Alexandre Belloni <[email protected]>
---
Documentation/devicetree/bindings/mips/mscc.txt | 43 +++++++++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mips/mscc.txt
diff --git a/Documentation/devicetree/bindings/mips/mscc.txt b/Documentation/devicetree/bindings/mips/mscc.txt
new file mode 100644
index 000000000000..ae15ec333542
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/mscc.txt
@@ -0,0 +1,43 @@
+* Microsemi MIPS CPUs
+
+Boards with a SoC of the Microsemi MIPS family shall have the following
+properties:
+
+Required properties:
+- compatible: "mscc,ocelot"
+
+
+* Other peripherals:
+
+o CPU chip regs:
+
+The SoC has a few registers (DEVCPU_GCB:CHIP_REGS) handling miscellaneous
+functionalities: chip ID, general purpose register for software use, reset
+controller, hardware status and configuration, efuses.
+
+Required properties:
+- compatible: Should be "mscc,ocelot-chip-regs", "simple-mfd", "syscon"
+- reg : Should contain registers location and length
+
+Example:
+ syscon@71070000 {
+ compatible = "mscc,ocelot-chip-regs", "simple-mfd", "syscon";
+ reg = <0x71070000 0x1c>;
+ };
+
+
+o CPU system control:
+
+The SoC has a few registers (ICPU_CFG:CPU_SYSTEM_CTRL) handling configuration of
+the CPU: 8 general purpose registers, reset control, CPU en/disabling, CPU
+endianness, CPU bus control, CPU status.
+
+Required properties:
+- compatible: Should be "mscc,ocelot-cpu-syscon", "syscon"
+- reg : Should contain registers location and length
+
+Example:
+ syscon@70000000 {
+ compatible = "mscc,ocelot-cpu-syscon", "syscon";
+ reg = <0x70000000 0x2c>;
+ };
--
2.16.2
Add a device tree for the Microsemi Ocelot PCB123 evaluation board.
Cc: Rob Herring <[email protected]>
Cc: [email protected]
Signed-off-by: Alexandre Belloni <[email protected]>
---
arch/mips/boot/dts/mscc/Makefile | 2 ++
arch/mips/boot/dts/mscc/ocelot_pcb123.dts | 27 +++++++++++++++++++++++++++
2 files changed, 29 insertions(+)
create mode 100644 arch/mips/boot/dts/mscc/ocelot_pcb123.dts
diff --git a/arch/mips/boot/dts/mscc/Makefile b/arch/mips/boot/dts/mscc/Makefile
index dd08e63a10ba..c51164537c02 100644
--- a/arch/mips/boot/dts/mscc/Makefile
+++ b/arch/mips/boot/dts/mscc/Makefile
@@ -1 +1,3 @@
+dtb-$(CONFIG_LEGACY_BOARD_OCELOT) += ocelot_pcb123.dtb
+
obj-y += $(patsubst %.dtb, %.dtb.o, $(dtb-y))
diff --git a/arch/mips/boot/dts/mscc/ocelot_pcb123.dts b/arch/mips/boot/dts/mscc/ocelot_pcb123.dts
new file mode 100644
index 000000000000..b4e3860c6cf4
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/ocelot_pcb123.dts
@@ -0,0 +1,27 @@
+//SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2017 Microsemi Corporation */
+
+/dts-v1/;
+
+#include "ocelot.dtsi"
+
+/ {
+ compatible = "mscc,ocelot-pcb123", "mscc,ocelot";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0e000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
--
2.16.2
Add myself as a maintainer for the Microsemi MIPS SoCs.
Signed-off-by: Alexandre Belloni <[email protected]>
---
MAINTAINERS | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 3bdc260e36b7..14ce8b290fea 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9156,6 +9156,15 @@ S: Maintained
F: drivers/usb/misc/usb251xb.c
F: Documentation/devicetree/bindings/usb/usb251xb.txt
+MICROSEMI MIPS SOCS
+M: Alexandre Belloni <[email protected]>
+L: [email protected]
+S: Maintained
+F: arch/mips/generic/board-ocelot.c
+F: arch/mips/configs/generic/board-ocelot.config
+F: arch/mips/boot/dts/mscc/
+F: Documentation/devicetree/bindings/mips/mscc.txt
+
MICROSEMI SMART ARRAY SMARTPQI DRIVER (smartpqi)
M: Don Brace <[email protected]>
L: [email protected]
--
2.16.2
Introduce support for the MIPS based Microsemi Ocelot SoCs.
Signed-off-by: Alexandre Belloni <[email protected]>
---
arch/mips/Makefile | 4 ++
arch/mips/configs/generic/board-ocelot.config | 36 ++++++++++++++
arch/mips/generic/Kconfig | 16 +++++++
arch/mips/generic/Makefile | 1 +
arch/mips/generic/board-ocelot.c | 67 +++++++++++++++++++++++++++
5 files changed, 124 insertions(+)
create mode 100644 arch/mips/configs/generic/board-ocelot.config
create mode 100644 arch/mips/generic/board-ocelot.c
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index d1ca839c3981..d2882244cf1f 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -543,6 +543,10 @@ generic_defconfig:
# now that the boards have been converted to use the generic kernel they are
# wrappers around the generic rules above.
#
+.PHONY: ocelot_defconfig
+ocelot_defconfig:
+ $(Q)$(MAKE) -f $(srctree)/Makefile 32r2el_defconfig BOARDS=ocelot
+
.PHONY: sead3_defconfig
sead3_defconfig:
$(Q)$(MAKE) -f $(srctree)/Makefile 32r2el_defconfig BOARDS=sead-3
diff --git a/arch/mips/configs/generic/board-ocelot.config b/arch/mips/configs/generic/board-ocelot.config
new file mode 100644
index 000000000000..fa4e8988ebc8
--- /dev/null
+++ b/arch/mips/configs/generic/board-ocelot.config
@@ -0,0 +1,36 @@
+# require CONFIG_32BIT=y
+# require CONFIG_CPU_MIPS32_R2=y
+
+CONFIG_LEGACY_BOARD_OCELOT=y
+
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_PLATFORM=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_UBI=y
+
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+
+CONFIG_GPIO_SYSFS=y
+
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+
+CONFIG_SPI=y
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_DESIGNWARE=y
+CONFIG_SPI_SPIDEV=y
+
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_OCELOT_RESET=y
+
+CONFIG_MAGIC_SYSRQ=y
diff --git a/arch/mips/generic/Kconfig b/arch/mips/generic/Kconfig
index 2ff3b17bfab1..ba9b2c8cce68 100644
--- a/arch/mips/generic/Kconfig
+++ b/arch/mips/generic/Kconfig
@@ -27,6 +27,22 @@ config LEGACY_BOARD_SEAD3
Enable this to include support for booting on MIPS SEAD-3 FPGA-based
development boards, which boot using a legacy boot protocol.
+comment "MSCC Ocelot doesn't work with SEAD3 enabled"
+ depends on LEGACY_BOARD_SEAD3
+
+config LEGACY_BOARD_OCELOT
+ bool "Support MSCC Ocelot boards"
+ depends on LEGACY_BOARD_SEAD3=n
+ select LEGACY_BOARDS
+ select MSCC_OCELOT
+
+config MSCC_OCELOT
+ bool
+ select GPIOLIB
+ select MSCC_OCELOT_IRQ
+ select SYS_HAS_EARLY_PRINTK
+ select USE_GENERIC_EARLY_PRINTK_8250
+
comment "FIT/UHI Boards"
config FIT_IMAGE_FDT_BOSTON
diff --git a/arch/mips/generic/Makefile b/arch/mips/generic/Makefile
index 5c31e0c4697d..d03a36f869a4 100644
--- a/arch/mips/generic/Makefile
+++ b/arch/mips/generic/Makefile
@@ -14,5 +14,6 @@ obj-y += proc.o
obj-$(CONFIG_YAMON_DT_SHIM) += yamon-dt.o
obj-$(CONFIG_LEGACY_BOARD_SEAD3) += board-sead3.o
+obj-$(CONFIG_LEGACY_BOARD_OCELOT) += board-ocelot.o
obj-$(CONFIG_KEXEC) += kexec.o
obj-$(CONFIG_VIRT_BOARD_RANCHU) += board-ranchu.o
diff --git a/arch/mips/generic/board-ocelot.c b/arch/mips/generic/board-ocelot.c
new file mode 100644
index 000000000000..44b5fdcc2ba0
--- /dev/null
+++ b/arch/mips/generic/board-ocelot.c
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Microsemi MIPS SoC support
+ *
+ * Copyright (c) 2017 Microsemi Corporation
+ */
+#include <asm/machine.h>
+#include <asm/prom.h>
+
+#define DEVCPU_GCB_CHIP_REGS_CHIP_ID 0x71070000
+#define CHIP_ID_PART_ID GENMASK(27, 12)
+
+#define OCELOT_PART_ID (0x7514 << 12)
+
+#define UART_UART 0x70100000
+
+static __init bool ocelot_detect(void)
+{
+ u32 rev;
+
+ rev = __raw_readl((void *)DEVCPU_GCB_CHIP_REGS_CHIP_ID);
+
+ if ((rev & CHIP_ID_PART_ID) != OCELOT_PART_ID)
+ return 0;
+
+ /* Copy command line from bootloader early for Initrd detection */
+ if (fw_arg0 < 10 && (fw_arg1 & 0xFFF00000) == 0x80000000) {
+ unsigned int prom_argc = fw_arg0;
+ const char **prom_argv = (const char **)fw_arg1;
+
+ if (prom_argc > 1 && strlen(prom_argv[1]) > 0)
+ /* ignore all built-in args if any f/w args given */
+ strcpy(arcs_cmdline, prom_argv[1]);
+ }
+
+ return 1;
+}
+
+static void __init ocelot_earlyprintk_init(void)
+{
+ void __iomem *uart_base;
+
+ uart_base = ioremap_nocache(UART_UART, 0x20);
+ setup_8250_early_printk_port((unsigned long)uart_base, 2, 50000);
+}
+
+static void __init ocelot_late_init(void)
+{
+ ocelot_earlyprintk_init();
+}
+
+static __init const void *ocelot_fixup_fdt(const void *fdt,
+ const void *match_data)
+{
+ /* This has to be done so late because ioremap needs to work */
+ late_time_init = ocelot_late_init;
+
+ return fdt;
+}
+
+extern char __dtb_ocelot_pcb123_begin[];
+
+MIPS_MACHINE(ocelot) = {
+ .fdt = __dtb_ocelot_pcb123_begin,
+ .fixup_fdt = ocelot_fixup_fdt,
+ .detect = ocelot_detect,
+};
--
2.16.2
Add a device tree include file for the Microsemi Ocelot SoC.
Cc: Rob Herring <[email protected]>
Cc: [email protected]
Signed-off-by: Alexandre Belloni <[email protected]>
---
arch/mips/boot/dts/Makefile | 1 +
arch/mips/boot/dts/mscc/Makefile | 1 +
arch/mips/boot/dts/mscc/ocelot.dtsi | 117 ++++++++++++++++++++++++++++++++++++
3 files changed, 119 insertions(+)
create mode 100644 arch/mips/boot/dts/mscc/Makefile
create mode 100644 arch/mips/boot/dts/mscc/ocelot.dtsi
diff --git a/arch/mips/boot/dts/Makefile b/arch/mips/boot/dts/Makefile
index e2c6f131c8eb..1e79cab8e269 100644
--- a/arch/mips/boot/dts/Makefile
+++ b/arch/mips/boot/dts/Makefile
@@ -4,6 +4,7 @@ subdir-y += cavium-octeon
subdir-y += img
subdir-y += ingenic
subdir-y += lantiq
+subdir-y += mscc
subdir-y += mti
subdir-y += netlogic
subdir-y += ni
diff --git a/arch/mips/boot/dts/mscc/Makefile b/arch/mips/boot/dts/mscc/Makefile
new file mode 100644
index 000000000000..dd08e63a10ba
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/Makefile
@@ -0,0 +1 @@
+obj-y += $(patsubst %.dtb, %.dtb.o, $(dtb-y))
diff --git a/arch/mips/boot/dts/mscc/ocelot.dtsi b/arch/mips/boot/dts/mscc/ocelot.dtsi
new file mode 100644
index 000000000000..8c3210577410
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/ocelot.dtsi
@@ -0,0 +1,117 @@
+//SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2017 Microsemi Corporation */
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mscc,ocelot";
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "mips,mips24KEc";
+ device_type = "cpu";
+ clocks = <&cpu_clk>;
+ reg = <0>;
+ };
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ cpuintc: interrupt-controller@0 {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ compatible = "mti,cpu-interrupt-controller";
+ };
+
+ cpu_clk: cpu-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <500000000>;
+ };
+
+ ahb_clk: ahb-clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clocks = <&cpu_clk>;
+ clock-div = <2>;
+ clock-mult = <1>;
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x70000000 0x2000000>;
+
+ interrupt-parent = <&intc>;
+
+ cpu_ctrl: syscon@0 {
+ compatible = "mscc,ocelot-cpu-syscon", "syscon";
+ reg = <0x0 0x2c>;
+ };
+
+ intc: interrupt-controller@70 {
+ compatible = "mscc,ocelot-icpu-intr";
+ reg = <0x70 0x70>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&cpuintc>;
+ interrupts = <2>;
+ };
+
+ uart0: serial@100000 {
+ pinctrl-0 = <&uart_pins>;
+ pinctrl-names = "default";
+ compatible = "ns16550a";
+ reg = <0x100000 0x20>;
+ interrupts = <6>;
+ clocks = <&ahb_clk>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+
+ status = "disabled";
+ };
+
+ uart2: serial@100800 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ compatible = "ns16550a";
+ reg = <0x100800 0x20>;
+ interrupts = <7>;
+ clocks = <&ahb_clk>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+
+ status = "disabled";
+ };
+
+ reset@1070008 {
+ compatible = "mscc,ocelot-chip-reset";
+ reg = <0x1070008 0x4>;
+ };
+
+ gpio: pinctrl@1070034 {
+ compatible = "mscc,ocelot-pinctrl";
+ reg = <0x1070034 0x68>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&gpio 0 0 22>;
+
+ uart_pins: uart-pins {
+ pins = "GPIO_6", "GPIO_7";
+ function = "uart";
+ };
+
+ uart2_pins: uart2-pins {
+ pins = "GPIO_12", "GPIO_13";
+ function = "uart2";
+ };
+ };
+ };
+};
--
2.16.2
On Tue, Mar 06, 2018 at 01:16:04PM +0100, Alexandre Belloni wrote:
> diff --git a/arch/mips/boot/dts/mscc/ocelot.dtsi b/arch/mips/boot/dts/mscc/ocelot.dtsi
> new file mode 100644
> index 000000000000..8c3210577410
> --- /dev/null
> +++ b/arch/mips/boot/dts/mscc/ocelot.dtsi
> @@ -0,0 +1,117 @@
> +//SPDX-License-Identifier: (GPL-2.0 OR MIT)
Niggle: there should be a space after // for consistency with other
files. Same in patch 3.
Cheers
James
On 07/03/2018 at 15:17:56 +0000, James Hogan wrote:
> On Tue, Mar 06, 2018 at 01:16:04PM +0100, Alexandre Belloni wrote:
> > diff --git a/arch/mips/boot/dts/mscc/ocelot.dtsi b/arch/mips/boot/dts/mscc/ocelot.dtsi
> > new file mode 100644
> > index 000000000000..8c3210577410
> > --- /dev/null
> > +++ b/arch/mips/boot/dts/mscc/ocelot.dtsi
> > @@ -0,0 +1,117 @@
> > +//SPDX-License-Identifier: (GPL-2.0 OR MIT)
>
> Niggle: there should be a space after // for consistency with other
> files. Same in patch 3.
>
Ah, yes...
If that is the only thing left, I can resend right away
--
Alexandre Belloni, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com
On Tue, Mar 06, 2018 at 01:16:06PM +0100, Alexandre Belloni wrote:
> diff --git a/arch/mips/Makefile b/arch/mips/Makefile
> index d1ca839c3981..d2882244cf1f 100644
> --- a/arch/mips/Makefile
> +++ b/arch/mips/Makefile
> @@ -543,6 +543,10 @@ generic_defconfig:
> # now that the boards have been converted to use the generic kernel they are
> # wrappers around the generic rules above.
> #
> +.PHONY: ocelot_defconfig
> +ocelot_defconfig:
> + $(Q)$(MAKE) -f $(srctree)/Makefile 32r2el_defconfig BOARDS=ocelot
FYI this conflicts with https://patchwork.linux-mips.org/patch/18596/,
but can be trivially fixed up when applied to the following, so no need
for you to rebase:
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index 2ed4c8927701..646a2d98012d 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -565,6 +565,9 @@ generic_defconfig:
# now that the boards have been converted to use the generic kernel they are
# wrappers around the generic rules above.
#
+legacy_defconfigs += ocelot_defconfig
+ocelot_defconfig-y := 32r2el_defconfig BOARDS=ocelot
+
legacy_defconfigs += sead3_defconfig
sead3_defconfig-y := 32r2el_defconfig BOARDS=sead-3
> +
> .PHONY: sead3_defconfig
> sead3_defconfig:
> $(Q)$(MAKE) -f $(srctree)/Makefile 32r2el_defconfig BOARDS=sead-3
> diff --git a/arch/mips/configs/generic/board-ocelot.config b/arch/mips/configs/generic/board-ocelot.config
> new file mode 100644
> index 000000000000..fa4e8988ebc8
> --- /dev/null
> +++ b/arch/mips/configs/generic/board-ocelot.config
> @@ -0,0 +1,36 @@
> +# require CONFIG_32BIT=y
That should be implied now by CPU_SUPPORTS_64BIT_KERNEL=n since
CONFIG_CPU_MIPS32_R2=y.
> +# require CONFIG_CPU_MIPS32_R2=y
> +static __init bool ocelot_detect(void)
> +{
> + u32 rev;
> +
> + rev = __raw_readl((void *)DEVCPU_GCB_CHIP_REGS_CHIP_ID);
How about a TLB check first, a bit like _kvm_mips_host_tlb_inv() in
arch/mips/kvm/tlb.c, i.e.:
int idx;
/* Look for the TLB entry set up by redboot before trying to use it */
write_c0_entryhi(DEVCPU_GCB_CHIP_REGS_CHIP_ID);
mtc0_tlbw_hazard();
tlb_probe();
tlb_probe_hazard();
idx = read_c0_index();
if (idx < 0)
return 0;
/* A TLB entry exists, lets assume its usable and check the CHIP ID */
rev = __raw_readl((void __iomem *)DEVCPU_GCB_CHIP_REGS_CHIP_ID);
(That assumes that if a TLB entry exists that it will be usable, which
isn't technically complete since the entry may not be marked valid, but
its probably sufficient in practice).
Incidentally you need to use __iomem there to avoid the following sparse
error:
arch/mips/generic/board-ocelot.c:21:28: warning: incorrect type in argument 1 (different address spaces)
arch/mips/generic/board-ocelot.c:21:28: expected void const volatile [noderef] <asn:2>*mem
arch/mips/generic/board-ocelot.c:21:28: got void *<noident>
Cheers
James
On Wed, Mar 07, 2018 at 04:27:51PM +0100, Alexandre Belloni wrote:
> On 07/03/2018 at 15:17:56 +0000, James Hogan wrote:
> > On Tue, Mar 06, 2018 at 01:16:04PM +0100, Alexandre Belloni wrote:
> > > diff --git a/arch/mips/boot/dts/mscc/ocelot.dtsi b/arch/mips/boot/dts/mscc/ocelot.dtsi
> > > new file mode 100644
> > > index 000000000000..8c3210577410
> > > --- /dev/null
> > > +++ b/arch/mips/boot/dts/mscc/ocelot.dtsi
> > > @@ -0,0 +1,117 @@
> > > +//SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >
> > Niggle: there should be a space after // for consistency with other
> > files. Same in patch 3.
> >
>
> Ah, yes...
>
> If that is the only thing left, I can resend right away
There are a couple of irqchip patches from v2 which have gone from the
latest versions:
https://patchwork.linux-mips.org/project/linux-mips/list/?series=568
and the vendor prefix too from v4:
https://patchwork.linux-mips.org/project/linux-mips/list/?series=856
I presume they're all still relevant. Were you expecting the irqchip
ones to go through MIPS too? We'd need an ack from the irqchip folk if
so.
Cheers
James
On 07/03/2018 at 15:56:07 +0000, James Hogan wrote:
> On Wed, Mar 07, 2018 at 04:27:51PM +0100, Alexandre Belloni wrote:
> > On 07/03/2018 at 15:17:56 +0000, James Hogan wrote:
> > > On Tue, Mar 06, 2018 at 01:16:04PM +0100, Alexandre Belloni wrote:
> > > > diff --git a/arch/mips/boot/dts/mscc/ocelot.dtsi b/arch/mips/boot/dts/mscc/ocelot.dtsi
> > > > new file mode 100644
> > > > index 000000000000..8c3210577410
> > > > --- /dev/null
> > > > +++ b/arch/mips/boot/dts/mscc/ocelot.dtsi
> > > > @@ -0,0 +1,117 @@
> > > > +//SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > >
> > > Niggle: there should be a space after // for consistency with other
> > > files. Same in patch 3.
> > >
> >
> > Ah, yes...
> >
> > If that is the only thing left, I can resend right away
>
> There are a couple of irqchip patches from v2 which have gone from the
> latest versions:
> https://patchwork.linux-mips.org/project/linux-mips/list/?series=568
>
I'll get those through the irqchip tree.
> and the vendor prefix too from v4:
> https://patchwork.linux-mips.org/project/linux-mips/list/?series=856
>
My mistake, I prepared my series from that patch, excluded instead of
from that patch, included.
> I presume they're all still relevant. Were you expecting the irqchip
> ones to go through MIPS too? We'd need an ack from the irqchip folk if
> so.
>
> Cheers
> James
--
Alexandre Belloni, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com
On Tue, Mar 6, 2018 at 6:16 AM, Alexandre Belloni
<[email protected]> wrote:
> Add a device tree include file for the Microsemi Ocelot SoC.
>
> Cc: Rob Herring <[email protected]>
> Cc: [email protected]
> Signed-off-by: Alexandre Belloni <[email protected]>
> ---
> arch/mips/boot/dts/Makefile | 1 +
> arch/mips/boot/dts/mscc/Makefile | 1 +
> arch/mips/boot/dts/mscc/ocelot.dtsi | 117 ++++++++++++++++++++++++++++++++++++
> 3 files changed, 119 insertions(+)
> create mode 100644 arch/mips/boot/dts/mscc/Makefile
> create mode 100644 arch/mips/boot/dts/mscc/ocelot.dtsi
>
> diff --git a/arch/mips/boot/dts/Makefile b/arch/mips/boot/dts/Makefile
> index e2c6f131c8eb..1e79cab8e269 100644
> --- a/arch/mips/boot/dts/Makefile
> +++ b/arch/mips/boot/dts/Makefile
> @@ -4,6 +4,7 @@ subdir-y += cavium-octeon
> subdir-y += img
> subdir-y += ingenic
> subdir-y += lantiq
> +subdir-y += mscc
> subdir-y += mti
> subdir-y += netlogic
> subdir-y += ni
> diff --git a/arch/mips/boot/dts/mscc/Makefile b/arch/mips/boot/dts/mscc/Makefile
> new file mode 100644
> index 000000000000..dd08e63a10ba
> --- /dev/null
> +++ b/arch/mips/boot/dts/mscc/Makefile
> @@ -0,0 +1 @@
> +obj-y += $(patsubst %.dtb, %.dtb.o, $(dtb-y))
> diff --git a/arch/mips/boot/dts/mscc/ocelot.dtsi b/arch/mips/boot/dts/mscc/ocelot.dtsi
> new file mode 100644
> index 000000000000..8c3210577410
> --- /dev/null
> +++ b/arch/mips/boot/dts/mscc/ocelot.dtsi
> @@ -0,0 +1,117 @@
> +//SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/* Copyright (c) 2017 Microsemi Corporation */
> +
> +/ {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "mscc,ocelot";
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + compatible = "mips,mips24KEc";
> + device_type = "cpu";
> + clocks = <&cpu_clk>;
> + reg = <0>;
> + };
> + };
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + cpuintc: interrupt-controller@0 {
Please compile with W=1 and fix any issues like this one which is a
unit-address without a reg property. Drop the unit-address.
> + #address-cells = <0>;
> + #interrupt-cells = <1>;
> + interrupt-controller;
> + compatible = "mti,cpu-interrupt-controller";
Hi Rob,
On Wed, Mar 07, 2018 at 10:08:28AM -0600, Rob Herring wrote:
> Please compile with W=1 and fix any issues like this one which is a
> unit-address without a reg property. Drop the unit-address.
I was just giving the BMIPS W=1 DT warnings a look, and a few look
spurious. I'd value your opinion on their legitimacy (its hard to care
about W=1 if spurious or seemingly pedantic warnings are going to be
common). e.g.
1)
arch/mips/boot/dts/brcm/bcm9ejtagprb.dtb: Warning (unit_address_vs_reg): Node /ubus/syscon-reboot@10000068 has a unit name, but no reg property
due to:
periph_cntl: syscon@fff8c000 {
compatible = "syscon";
reg = <0xfff8c000 0xc>;
native-endian;
};
reboot: syscon-reboot@fff8c008 {
compatible = "syscon-reboot";
regmap = <&periph_cntl>;
offset = <0x8>;
mask = <0x1>;
};
That doesn't seem to take regmap into account. Would you strictly drop
the unit-address in this case, or is there a way the DT compiler can be
fixed (i presume offset and mask are binding specific, so the best it
could do is probably to allow the unit-address due to the regmap without
checking the actual address)?
2)
arch/mips/boot/dts/brcm/bcm9ejtagprb.dtb: Warning (simple_bus_reg): Node /ubus/syscon-reboot@10000068 missing or empty reg/ranges property
Same code as above. Should syscon-reboot be outside of the simple-bus
that both nodes are in, or is it fine there? There's a similar warning
from a DTS which has a syscon property instead of regmap.
3)
arch/mips/boot/dts/brcm/bcm97425svmb.dtb: Warning (simple_bus_reg): Node /rdb@10000000/spi@41c000 simple-bus unit address format error, expected "419920"
qspi: spi@41c000 {
#address-cells = <0x1>;
#size-cells = <0x0>;
compatible = "brcm,spi-bcm-qspi",
"brcm,spi-brcmstb-qspi";
clocks = <&upg_clk>;
reg = <0x419920 0x4 0x41c200 0x188 0x41c000 0x50>;
reg-names = "cs_reg", "hif_mspi", "bspi";
...
Well 41c000 is one of the reg entries, just not the first. I presume
bspi is the "main" one, perhaps that should come first since we have
reg-names, but even that could potentially confuse driver code if it
didn't find reg resources by name (in this case it does appear to, so
perhaps that would fine)?
Thanks
James