This series is a major overhaul and adds support for the V1.1 hardware
revision of the Toradex Apalis T30 system on module.
Changes in v2:
- Clean-up PCIe controller/port status' as well.
- Also move serial UART "nvidia,tegra30-hsuart" compatible to module
level device trees.
- Also add two missing newlines.
- Also replace underscores in node names with dashes.
- Explicitly disable input of BKL1_ON as well.
- Replace underscores in node names with dashes.
- When running some more tests I realized that the reg-addr should
really be 0x3f. Fix this.
- Get rid of fake clocks simple bus as suggested by Rob.
- Replace "[PATCH 27/28] ARM: tegra: apalis_t30: fix pcie switch vendor
compatible" with "[PATCH v2 26/34] dt-bindings: add broadcom (formerly
plx technology) vendor prefix" as suggested by Stefan.
- New patch as suggested by Rob.
- New patch.
- Drop "[PATCH 01/28] ARM: tegra: apalis_t30: enable broken-hpi on emmc"
which should already be handled by the broken-hpi quirk as pointed out
by Dmitry. If I would find more eMMC parts which exhibit the issue I
will add them to the quirk as a separate patch.
- Updated V1.1 device trees with all applicable previous fixes.
Marcel Ziswiler (34):
ARM: tegra: apalis_t30: fix mmc1 cmd pull-up
ARM: tegra: apalis_t30: pull-up sd card detect pins
ARM: tegra: apalis_t30: add local-mac-address property
ARM: tegra: apalis_t30: reorder pcie properties
ARM: tegra: apalis_t30: annotate/clean-up pcie controller/port nodes
ARM: tegra: apalis_t30: reorder host1x/hdmi properties
ARM: tegra: apalis_t30: regulator clean-up
ARM: tegra: apalis_t30: add missing regulators
ARM: tegra: apalis_t30: annotate uarts and move compatible to board
ARM: tegra: apalis_t30: drop unused cami2c label
ARM: tegra: apalis_t30: white-space/newline clean-up
ARM: tegra: apalis_t30: drop unused mmc1/sd1 labels
ARM: tegra: apalis_t30: annotate mmc1/sd1
ARM: tegra: apalis_t30: move dr_mode property from phy to controller
ARM: tegra: apalis_t30: reorder backlight properties
ARM: tegra: apalis_t30: drop pwmleds
ARM: tegra: apalis_t30: pinmux clean-up
ARM: tegra: apalis_t30: add missing pinmux
ARM: tegra: apalis_t30: use proper irq-gpio for stmpe811
ARM: tegra: apalis_t30: further lm95245 temperature sensor annotation
ARM: tegra: apalis_t30: add i2c-thermtrip
ARM: tegra: apalis_t30: add proper emmc vmmc and vqmmc supplies
ARM: tegra: apalis_t30: enable emmc ddr52 mode
ARM: tegra: apalis_t30: get rid of fake clocks simple bus
ARM: tegra: apalis_t30: line break long compatible property line
dt-bindings: add broadcom (formerly plx technology) vendor prefix
ARM: tegra: apalis_t30: drop module level model and compatible
ARM: tegra: apalis_t30: drop obsolete spidev nodes
ARM: tegra: apalis_t30: hog group for pcie switch reset gpio
ARM: tegra: apalis_t30: rename hdmiddc to hdmi_ddc
ARM: tegra: apalis_t30: rename tps65911@2d, stmpe811@41 and
tps62362@60
ARM: tegra: apalis_t30: fix mcp2515 can controller interrupt polarity
ARM: tegra: apalis_t30: move hda node from carrier to module
ARM: tegra: apalis_t30: support v1.1 hardware revision
Documentation/devicetree/bindings/arm/tegra.txt | 2 +
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/tegra30-apalis-eval.dts | 148 +--
arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts | 266 +++++
arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi | 1189 ++++++++++++++++++++
arch/arm/boot/dts/tegra30-apalis.dtsi | 705 +++++++++---
7 files changed, 2064 insertions(+), 248 deletions(-)
create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
--
2.14.4
From: Marcel Ziswiler <[email protected]>
In order to avoid any floating SD card detect pins as may e.g. happen on
Ixora V1.1A pull them all up.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis.dtsi | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index e749e047db7a..69bb11c31d77 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -194,7 +194,7 @@
pv3 {
nvidia,pins = "pv3";
nvidia,function = "rsvd2";
- nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
@@ -260,7 +260,7 @@
clk2_req_pcc5 {
nvidia,pins = "clk2_req_pcc5";
nvidia,function = "rsvd2";
- nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Annotate MMC1/SD1.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis-eval.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 3f25bb307397..15e9de06c59a 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -134,6 +134,7 @@
status = "okay";
};
+ /* Apalis SD1 */
sdhci@78000000 {
status = "okay";
bus-width = <4>;
@@ -142,6 +143,7 @@
no-1-8-v;
};
+ /* Apalis MMC1 */
sdhci@78000400 {
status = "okay";
bus-width = <8>;
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Move dr_mode property from USB PHY node to controller.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis-eval.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 15e9de06c59a..9f2392a05532 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -155,11 +155,11 @@
/* EHCI instance 0: USB1_DP/N -> USBO1_DP/N */
usb@7d000000 {
status = "okay";
+ dr_mode = "otg";
};
usb-phy@7d000000 {
status = "okay";
- dr_mode = "otg";
vbus-supply = <®_usbo1_vbus>;
};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Drop pwmleds in favour of using regular PWMs.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis-eval.dts | 22 ----------------------
1 file changed, 22 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 300ce726ff4d..5d1bc8560dbe 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -215,28 +215,6 @@
power-supply = <®_3v3>;
};
- pwmleds {
- compatible = "pwm-leds";
-
- pwm1 {
- label = "PWM1";
- pwms = <&pwm 3 19600>;
- max-brightness = <255>;
- };
-
- pwm2 {
- label = "PWM2";
- pwms = <&pwm 2 19600>;
- max-brightness = <255>;
- };
-
- pwm3 {
- label = "PWM3";
- pwms = <&pwm 1 19600>;
- max-brightness = <255>;
- };
- };
-
reg_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3.3V_SW";
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Clean-up pinmuxing:
- white-space clean-up
- explicitly disable input of BKL1_ON, BKL1_PWM and BKL1_PWM_EN#
- annotate Apalis I2C3 usage for CAM
- get rid of nvidia,lock property
- add missing eMMC sdmmc4_cmd_pt7 and explicitly enable input
- explicitly disable lcd_dc1_pd2 (e.g. LM95245 I2C address pin)
- annotate TOUCH_PEN_INT# being on-module
- As underscores in node names are not recommended replace them all
where possible with dashes.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- Also replace underscores in node names with dashes.
- Explicitly disable input of BKL1_ON as well.
arch/arm/boot/dts/tegra30-apalis.dtsi | 88 ++++++++++++++++++-----------------
1 file changed, 45 insertions(+), 43 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index e84feac9b992..cb587670a5af 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -63,18 +63,18 @@
state_default: pinmux {
/* Analogue Audio (On-module) */
- clk1_out_pw4 {
+ clk1-out-pw4 {
nvidia,pins = "clk1_out_pw4";
nvidia,function = "extperiph1";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_DISABLE>;
};
- dap3_fs_pp0 {
- nvidia,pins = "dap3_fs_pp0",
- "dap3_sclk_pp3",
- "dap3_din_pp1",
- "dap3_dout_pp2";
+ dap3-fs-pp0 {
+ nvidia,pins = "dap3_fs_pp0",
+ "dap3_sclk_pp3",
+ "dap3_din_pp1",
+ "dap3_dout_pp2";
nvidia,function = "i2s2";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
@@ -86,25 +86,28 @@
nvidia,function = "rsvd4";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
};
/* Apalis BKL1_PWM */
- uart3_rts_n_pc0 {
+ uart3-rts-n-pc0 {
nvidia,pins = "uart3_rts_n_pc0";
nvidia,function = "pwm0";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
};
/* BKL1_PWM_EN#, disable TPS65911 PMIC PWM backlight */
- uart3_cts_n_pa1 {
+ uart3-cts-n-pa1 {
nvidia,pins = "uart3_cts_n_pa1";
nvidia,function = "rsvd2";
nvidia,pull = <TEGRA_PIN_PULL_UP>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
};
/* Apalis CAN1 on SPI6 */
- spi2_cs0_n_px3 {
+ spi2-cs0-n-px3 {
nvidia,pins = "spi2_cs0_n_px3",
"spi2_miso_px1",
"spi2_mosi_px0",
@@ -114,7 +117,7 @@
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
/* CAN_INT1 */
- spi2_cs1_n_pw2 {
+ spi2-cs1-n-pw2 {
nvidia,pins = "spi2_cs1_n_pw2";
nvidia,function = "spi3";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -123,7 +126,7 @@
};
/* Apalis CAN2 on SPI4 */
- gmi_a16_pj7 {
+ gmi-a16-pj7 {
nvidia,pins = "gmi_a16_pj7",
"gmi_a17_pb0",
"gmi_a18_pb1",
@@ -134,7 +137,7 @@
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
/* CAN_INT2 */
- spi2_cs2_n_pw3 {
+ spi2-cs2-n-pw3 {
nvidia,pins = "spi2_cs2_n_pw3";
nvidia,function = "spi3";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -143,20 +146,20 @@
};
/* Apalis Digital Audio */
- clk1_req_pee2 {
+ clk1-req-pee2 {
nvidia,pins = "clk1_req_pee2";
nvidia,function = "hda";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
- clk2_out_pw5 {
+ clk2-out-pw5 {
nvidia,pins = "clk2_out_pw5";
nvidia,function = "extperiph2";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_DISABLE>;
};
- dap1_fs_pn0 {
+ dap1-fs-pn0 {
nvidia,pins = "dap1_fs_pn0",
"dap1_din_pn1",
"dap1_dout_pn2",
@@ -166,26 +169,25 @@
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
- /* Apalis I2C3 */
- cam_i2c_scl_pbb1 {
+ /* Apalis I2C3 (CAM) */
+ cam-i2c-scl-pbb1 {
nvidia,pins = "cam_i2c_scl_pbb1",
"cam_i2c_sda_pbb2";
nvidia,function = "i2c3";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
- nvidia,lock = <TEGRA_PIN_DISABLE>;
nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
/* Apalis MMC1 */
- sdmmc3_clk_pa6 {
+ sdmmc3-clk-pa6 {
nvidia,pins = "sdmmc3_clk_pa6";
nvidia,function = "sdmmc3";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
- sdmmc3_dat0_pb7 {
+ sdmmc3-dat0-pb7 {
nvidia,pins = "sdmmc3_cmd_pa7",
"sdmmc3_dat0_pb7",
"sdmmc3_dat1_pb6",
@@ -241,7 +243,7 @@
};
/* Apalis RESET_MOCI# */
- gmi_rst_n_pi4 {
+ gmi-rst-n-pi4 {
nvidia,pins = "gmi_rst_n_pi4";
nvidia,function = "gmi";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -249,13 +251,13 @@
};
/* Apalis SD1 */
- sdmmc1_clk_pz0 {
+ sdmmc1-clk-pz0 {
nvidia,pins = "sdmmc1_clk_pz0";
nvidia,function = "sdmmc1";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
- sdmmc1_cmd_pz1 {
+ sdmmc1-cmd-pz1 {
nvidia,pins = "sdmmc1_cmd_pz1",
"sdmmc1_dat0_py7",
"sdmmc1_dat1_py6",
@@ -266,7 +268,7 @@
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
/* Apalis SD1_CD# */
- clk2_req_pcc5 {
+ clk2-req-pcc5 {
nvidia,pins = "clk2_req_pcc5";
nvidia,function = "rsvd2";
nvidia,pull = <TEGRA_PIN_PULL_UP>;
@@ -275,7 +277,7 @@
};
/* Apalis SPI1 */
- spi1_sck_px5 {
+ spi1-sck-px5 {
nvidia,pins = "spi1_sck_px5",
"spi1_mosi_px4",
"spi1_miso_px7",
@@ -286,7 +288,7 @@
};
/* Apalis SPI2 */
- lcd_sck_pz4 {
+ lcd-sck-pz4 {
nvidia,pins = "lcd_sck_pz4",
"lcd_sdout_pn5",
"lcd_sdin_pz2",
@@ -297,7 +299,7 @@
};
/* Apalis UART1 */
- ulpi_data0 {
+ ulpi-data0 {
nvidia,pins = "ulpi_data0_po1",
"ulpi_data1_po2",
"ulpi_data2_po3",
@@ -312,7 +314,7 @@
};
/* Apalis UART2 */
- ulpi_clk_py0 {
+ ulpi-clk-py0 {
nvidia,pins = "ulpi_clk_py0",
"ulpi_dir_py1",
"ulpi_nxt_py2",
@@ -323,7 +325,7 @@
};
/* Apalis UART3 */
- uart2_rxd_pc3 {
+ uart2-rxd-pc3 {
nvidia,pins = "uart2_rxd_pc3",
"uart2_txd_pc2";
nvidia,function = "uartb";
@@ -332,7 +334,7 @@
};
/* Apalis UART4 */
- uart3_rxd_pw7 {
+ uart3-rxd-pw7 {
nvidia,pins = "uart3_rxd_pw7",
"uart3_txd_pw6";
nvidia,function = "uartc";
@@ -341,7 +343,7 @@
};
/* Apalis USBO1_EN */
- gen2_i2c_scl_pt5 {
+ gen2-i2c-scl-pt5 {
nvidia,pins = "gen2_i2c_scl_pt5";
nvidia,function = "rsvd4";
nvidia,open-drain = <TEGRA_PIN_DISABLE>;
@@ -350,7 +352,7 @@
};
/* Apalis USBO1_OC# */
- gen2_i2c_sda_pt6 {
+ gen2-i2c-sda-pt6 {
nvidia,pins = "gen2_i2c_sda_pt6";
nvidia,function = "rsvd4";
nvidia,open-drain = <TEGRA_PIN_DISABLE>;
@@ -369,14 +371,16 @@
};
/* eMMC (On-module) */
- sdmmc4_clk_pcc4 {
+ sdmmc4-clk-pcc4 {
nvidia,pins = "sdmmc4_clk_pcc4",
+ "sdmmc4_cmd_pt7",
"sdmmc4_rst_n_pcc3";
nvidia,function = "sdmmc4";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
- sdmmc4_dat0_paa0 {
+ sdmmc4-dat0-paa0 {
nvidia,pins = "sdmmc4_dat0_paa0",
"sdmmc4_dat1_paa1",
"sdmmc4_dat2_paa2",
@@ -388,6 +392,7 @@
nvidia,function = "sdmmc4";
nvidia,pull = <TEGRA_PIN_PULL_UP>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
/* LVDS Transceiver Configuration */
@@ -400,7 +405,6 @@
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,lock = <TEGRA_PIN_DISABLE>;
};
pbb3 {
nvidia,pins = "pbb3",
@@ -411,18 +415,16 @@
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,lock = <TEGRA_PIN_DISABLE>;
};
/* Power I2C (On-module) */
- pwr_i2c_scl_pz6 {
+ pwr-i2c-scl-pz6 {
nvidia,pins = "pwr_i2c_scl_pz6",
"pwr_i2c_sda_pz7";
nvidia,function = "i2cpwr";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
- nvidia,lock = <TEGRA_PIN_DISABLE>;
nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
@@ -431,15 +433,15 @@
* temperature sensor therefore requires disabling for
* now
*/
- lcd_dc1_pd2 {
+ lcd-dc1-pd2 {
nvidia,pins = "lcd_dc1_pd2";
nvidia,function = "rsvd3";
- nvidia,pull = <TEGRA_PIN_PULL_NONE>;
- nvidia,tristate = <TEGRA_PIN_DISABLE>;
- nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
};
- /* TOUCH_PEN_INT# */
+ /* TOUCH_PEN_INT# (On-module) */
pv0 {
nvidia,pins = "pv0";
nvidia,function = "rsvd1";
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Add proper eMMC vmmc and vqmmc supplies e.g. fixing signalling voltage.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 02d0117e9398..2e2cdd454fe3 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -1092,6 +1092,8 @@
status = "okay";
bus-width = <8>;
non-removable;
+ vmmc-supply = <®_module_3v3>; /* VCC */
+ vqmmc-supply = <®_1v8_vio>; /* VCCQ */
};
clocks {
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Fix the MCP2515 SPI CAN controller interrupt polarity which according
to its datasheet defaults to low-active aka falling edge.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- New patch.
arch/arm/boot/dts/tegra30-apalis.dtsi | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index a31b112f631d..e44b2bce6736 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -1039,7 +1039,7 @@
reg = <1>;
clocks = <&clk16m>;
interrupt-parent = <&gpio>;
- interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_RISING>;
+ interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
spi-max-frequency = <10000000>;
};
};
@@ -1054,7 +1054,7 @@
reg = <0>;
clocks = <&clk16m>;
interrupt-parent = <&gpio>;
- interrupts = <TEGRA_GPIO(W, 2) IRQ_TYPE_EDGE_RISING>;
+ interrupts = <TEGRA_GPIO(W, 2) IRQ_TYPE_EDGE_FALLING>;
spi-max-frequency = <10000000>;
};
};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Annotate UARTs and move the serial UART "nvidia,tegra30-hsuart"
compatible definitions from the carrier board to the module level device
trees. One could still override this in a custom carrier board device
tree if required.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- Also move serial UART "nvidia,tegra30-hsuart" compatible to module
level device trees.
arch/arm/boot/dts/tegra30-apalis-eval.dts | 7 ++++---
arch/arm/boot/dts/tegra30-apalis.dtsi | 12 ++++++++++++
2 files changed, 16 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 14a62b5111ec..cd4e45759ac8 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -45,22 +45,23 @@
};
};
+ /* Apalis UART1 */
serial@70006000 {
status = "okay";
};
+ /* Apalis UART2 */
serial@70006040 {
- compatible = "nvidia,tegra30-hsuart";
status = "okay";
};
+ /* Apalis UART3 */
serial@70006200 {
- compatible = "nvidia,tegra30-hsuart";
status = "okay";
};
+ /* Apalis UART4 */
serial@70006300 {
- compatible = "nvidia,tegra30-hsuart";
status = "okay";
};
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 3b2e15519e4b..7e9d1b022982 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -449,6 +449,18 @@
};
};
+ serial@70006040 {
+ compatible = "nvidia,tegra30-hsuart";
+ };
+
+ serial@70006200 {
+ compatible = "nvidia,tegra30-hsuart";
+ };
+
+ serial@70006300 {
+ compatible = "nvidia,tegra30-hsuart";
+ };
+
hdmiddc: i2c@7000c700 {
clock-frequency = <10000>;
};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Drop model and compatible nodes from the module level device tree as
they get overridden by the carrier board device tree anyway.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- New patch as suggested by Rob.
arch/arm/boot/dts/tegra30-apalis.dtsi | 3 ---
1 file changed, 3 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index d80101df2228..e7793f3b19d2 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -7,9 +7,6 @@
* 2GB: V1.0B, V1.0C, V1.0E, V1.1A
*/
/ {
- model = "Toradex Apalis T30";
- compatible = "toradex,apalis_t30", "nvidia,tegra30";
-
memory@80000000 {
reg = <0x80000000 0x40000000>;
};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Drop obsolete spidev device tree nodes as nowadays one should do this
by binding the spidev driver to specific instances/chip selects at
runtime.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- New patch.
arch/arm/boot/dts/tegra30-apalis-eval.dts | 12 ------------
1 file changed, 12 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 97e2f1822a94..bbde98fd9712 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -111,24 +111,12 @@
spi@7000d400 {
status = "okay";
spi-max-frequency = <25000000>;
-
- spidev0: spidev@1 {
- compatible = "spidev";
- reg = <1>;
- spi-max-frequency = <25000000>;
- };
};
/* SPI5: Apalis SPI2 */
spi@7000dc00 {
status = "okay";
spi-max-frequency = <25000000>;
-
- spidev1: spidev@2 {
- compatible = "spidev";
- reg = <2>;
- spi-max-frequency = <25000000>;
- };
};
hda@70030000 {
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Add mmc-ddr-1_8v property enabling eMMC DDR52 mode.
root@apalis-t30:~# cat /sys/kernel/debug/mmc1/ios
clock: 52000000 Hz
actual clock: 52000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 3 (8 bits)
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
driver type: 0 (driver type B)
root@apalis-t30:~# hdparm -t /dev/mmcblk1
/dev/mmcblk1:
Timing buffered disk reads: 232 MB in 3.01 seconds = 77.10 MB/sec
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 2e2cdd454fe3..6d6f17422478 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -1094,6 +1094,7 @@
non-removable;
vmmc-supply = <®_module_3v3>; /* VCC */
vqmmc-supply = <®_1v8_vio>; /* VCCQ */
+ mmc-ddr-1_8v;
};
clocks {
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Get rid of the fake clocks simple bus and use node names as per the
actual schematics.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- Get rid of fake clocks simple bus as suggested by Rob.
arch/arm/boot/dts/tegra30-apalis.dtsi | 27 +++++++++------------------
1 file changed, 9 insertions(+), 18 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 6d6f17422478..d80101df2228 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -1097,25 +1097,16 @@
mmc-ddr-1_8v;
};
- clocks {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- clk32k_in: clk@0 {
- compatible = "fixed-clock";
- reg = <0>;
- #clock-cells = <0>;
- clock-frequency = <32768>;
- };
+ clk32k_in: xtal1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
- clk16m: clk@1 {
- compatible = "fixed-clock";
- reg = <1>;
- #clock-cells = <0>;
- clock-frequency = <16000000>;
- clock-output-names = "clk16m";
- };
+ clk16m: osc4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
};
reg_1v8_avdd_hdmi_pll: regulator-1v8-avdd-hdmi-pll {
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Use proper irq-gpio for stmpe811 touch controller.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index e37d22e2ceef..43d914f754e8 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -975,8 +975,7 @@
stmpe811@41 {
compatible = "st,stmpe811";
reg = <0x41>;
- interrupts = <TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
- interrupt-parent = <&gpio>;
+ irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
id = <0>;
blocks = <0x5>;
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Rename hdmiddc to hdmi_ddc to be more in-line with other device trees.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- New patch.
arch/arm/boot/dts/tegra30-apalis-eval.dts | 2 +-
arch/arm/boot/dts/tegra30-apalis.dtsi | 4 ++--
2 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 9d9dda6c0246..9381f65a9bf5 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -103,7 +103,7 @@
};
/* DDC: I2C2_SDA/SCL on MXM3 pin 205/207 (e.g. display EDID) */
- hdmiddc: i2c@7000c700 {
+ i2c@7000c700 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index e7793f3b19d2..f15954995231 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -46,7 +46,7 @@
host1x@50000000 {
hdmi@54280000 {
- nvidia,ddc-i2c-bus = <&hdmiddc>;
+ nvidia,ddc-i2c-bus = <&hdmi_ddc>;
nvidia,hpd-gpio =
<&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
pll-supply = <®_1v8_avdd_hdmi_pll>;
@@ -831,7 +831,7 @@
compatible = "nvidia,tegra30-hsuart";
};
- hdmiddc: i2c@7000c700 {
+ hdmi_ddc: i2c@7000c700 {
clock-frequency = <10000>;
};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Reorder Host1x/HDMI properties.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis.dtsi | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index c810c044025a..648db524abae 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -48,12 +48,11 @@
host1x@50000000 {
hdmi@54280000 {
- vdd-supply = <&avdd_hdmi_3v3_reg>;
- pll-supply = <&avdd_hdmi_pll_1v8_reg>;
-
+ nvidia,ddc-i2c-bus = <&hdmiddc>;
nvidia,hpd-gpio =
<&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
- nvidia,ddc-i2c-bus = <&hdmiddc>;
+ pll-supply = <&avdd_hdmi_pll_1v8_reg>;
+ vdd-supply = <&avdd_hdmi_3v3_reg>;
};
};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Further LM95245 temperature sensor annotation.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 43d914f754e8..c3e37d944c62 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -1009,7 +1009,7 @@
/*
* LM95245 temperature sensor
- * Note: OVERT_N directly connected to PMIC PWRDN
+ * Note: OVERT1# directly connected to TPS65911 PMIC PWRDN
*/
temp-sensor@4c {
compatible = "national,lm95245";
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Add i2c-thermtrip which would set the DEV_OFF bit in the DCDC control
register of the TPS65911 PMIC.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- When running some more tests I realized that the reg-addr should
really be 0x3f. Fix this.
arch/arm/boot/dts/tegra30-apalis.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index c3e37d944c62..02d0117e9398 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -1071,6 +1071,14 @@
nvidia,core-pwr-off-time = <0>;
nvidia,core-power-req-active-high;
nvidia,sys-clock-req-active-high;
+
+ /* Set DEV_OFF bit in DCDC control register of TPS65911 PMIC */
+ i2c-thermtrip {
+ nvidia,i2c-controller-id = <4>;
+ nvidia,bus-addr = <0x2d>;
+ nvidia,reg-addr = <0x3f>;
+ nvidia,reg-data = <0x1>;
+ };
};
ahub@70080000 {
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Add missing regulators:
- reg_module_3v3_audio being VDDA supply of SGTL5000
- VDDD supply of SGTL5000 actually being reg_1v8_vio
- carrier board HDMI supply being reg_5v0
- carrier board reg_3v3 actually being backlight and panel power supply
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis-eval.dts | 10 ++++++++++
arch/arm/boot/dts/tegra30-apalis.dtsi | 11 ++++++++++-
2 files changed, 20 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 07da481bc441..14a62b5111ec 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -41,6 +41,7 @@
};
hdmi@54280000 {
status = "okay";
+ hdmi-supply = <®_5v0>;
};
};
@@ -185,6 +186,7 @@
default-brightness-level = <6>;
/* BKL1_ON */
enable-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+ power-supply = <®_3v3>;
};
gpio-keys {
@@ -207,6 +209,7 @@
compatible = "edt,et057090dhu", "simple-panel";
backlight = <&backlight>;
+ power-supply = <®_3v3>;
};
pwmleds {
@@ -231,6 +234,13 @@
};
};
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3.3V_SW";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
reg_5v0: regulator-5v0 {
compatible = "regulator-fixed";
regulator-name = "5V_SW";
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 214a23722ab4..3b2e15519e4b 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -465,7 +465,8 @@
sgtl5000: codec@a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
- VDDA-supply = <®_module_3v3>;
+ VDDA-supply = <®_module_3v3_audio>;
+ VDDD-supply = <®_1v8_vio>;
VDDIO-supply = <®_module_3v3>;
clocks = <&tegra_car TEGRA30_CLK_EXTERN1>;
};
@@ -758,6 +759,14 @@
regulator-always-on;
};
+ reg_module_3v3_audio: regulator-module-3v3-audio {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3_AUDIO_AVDD_S";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
sound {
compatible = "toradex,tegra-audio-sgtl5000-apalis_t30",
"nvidia,tegra-audio-sgtl5000";
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Just cosmetic regulator clean-up.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis-eval.dts | 62 ++++++-------
arch/arm/boot/dts/tegra30-apalis.dtsi | 140 +++++++++++++-----------------
2 files changed, 88 insertions(+), 114 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index e3c70e7d8d37..07da481bc441 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -153,7 +153,7 @@
usb-phy@7d000000 {
status = "okay";
dr_mode = "otg";
- vbus-supply = <&usbo1_vbus_reg>;
+ vbus-supply = <®_usbo1_vbus>;
};
/* EHCI instance 1: USB2_DP/N -> USBH2_DP/N */
@@ -163,7 +163,7 @@
usb-phy@7d004000 {
status = "okay";
- vbus-supply = <&usbh_vbus_reg>;
+ vbus-supply = <®_usbh_vbus>;
};
/* EHCI instance 2: USB3_DP/N -> USBH3_DP/N */
@@ -173,7 +173,7 @@
usb-phy@7d008000 {
status = "okay";
- vbus-supply = <&usbh_vbus_reg>;
+ vbus-supply = <®_usbh_vbus>;
};
backlight: backlight {
@@ -231,38 +231,32 @@
};
};
- regulators {
- sys_5v0_reg: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "5v0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5V_SW";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
- /* USBO1_EN */
- usbo1_vbus_reg: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "usbo1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio TEGRA_GPIO(T, 5) GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin-supply = <&sys_5v0_reg>;
- };
+ /* USBO1_EN */
+ reg_usbo1_vbus: regulator-usbo1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_USBO1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(T, 5) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_5v0>;
+ };
- /* USBH_EN */
- usbh_vbus_reg: regulator@3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "usbh_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin-supply = <&sys_5v0_reg>;
- };
+ /* USBH_EN */
+ reg_usbh_vbus: regulator-usbh-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_USBH(2A|2C|2D|3|4)";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_5v0>;
};
};
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 648db524abae..214a23722ab4 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -20,8 +20,8 @@
avdd-pexb-supply = <&vdd2_reg>;
avdd-pex-pll-supply = <&vdd2_reg>;
avdd-plle-supply = <&ldo6_reg>;
- hvdd-pex-supply = <&sys_3v3_reg>;
- vddio-pex-ctl-supply = <&sys_3v3_reg>;
+ hvdd-pex-supply = <®_module_3v3>;
+ vddio-pex-ctl-supply = <®_module_3v3>;
vdd-pexa-supply = <&vdd2_reg>;
vdd-pexb-supply = <&vdd2_reg>;
@@ -51,8 +51,8 @@
nvidia,ddc-i2c-bus = <&hdmiddc>;
nvidia,hpd-gpio =
<&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
- pll-supply = <&avdd_hdmi_pll_1v8_reg>;
- vdd-supply = <&avdd_hdmi_3v3_reg>;
+ pll-supply = <®_1v8_avdd_hdmi_pll>;
+ vdd-supply = <®_3v3_avdd_hdmi>;
};
};
@@ -465,8 +465,8 @@
sgtl5000: codec@a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
- VDDA-supply = <&sys_3v3_reg>;
- VDDIO-supply = <&sys_3v3_reg>;
+ VDDA-supply = <®_module_3v3>;
+ VDDIO-supply = <®_module_3v3>;
clocks = <&tegra_car TEGRA30_CLK_EXTERN1>;
};
@@ -483,43 +483,38 @@
#gpio-cells = <2>;
gpio-controller;
- vcc1-supply = <&sys_3v3_reg>;
- vcc2-supply = <&sys_3v3_reg>;
- vcc3-supply = <&vio_reg>;
- vcc4-supply = <&sys_3v3_reg>;
- vcc5-supply = <&sys_3v3_reg>;
- vcc6-supply = <&vio_reg>;
- vcc7-supply = <&charge_pump_5v0_reg>;
- vccio-supply = <&sys_3v3_reg>;
+ vcc1-supply = <®_module_3v3>;
+ vcc2-supply = <®_module_3v3>;
+ vcc3-supply = <®_1v8_vio>;
+ vcc4-supply = <®_module_3v3>;
+ vcc5-supply = <®_module_3v3>;
+ vcc6-supply = <®_1v8_vio>;
+ vcc7-supply = <®_5v0_charge_pump>;
+ vccio-supply = <®_module_3v3>;
regulators {
- /* SW1: +V1.35_VDDIO_DDR */
vdd1_reg: vdd1 {
- regulator-name = "vddio_ddr_1v35";
+ regulator-name = "+V1.35_VDDIO_DDR";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
};
- /* SW2: +V1.05 */
vdd2_reg: vdd2 {
- regulator-name =
- "vdd_pexa,vdd_pexb,vdd_sata";
+ regulator-name = "+V1.05";
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
};
- /* SW CTRL: +V1.0_VDD_CPU */
vddctrl_reg: vddctrl {
- regulator-name = "vdd_cpu,vdd_sys";
+ regulator-name = "+V1.0_VDD_CPU";
regulator-min-microvolt = <1150000>;
regulator-max-microvolt = <1150000>;
regulator-always-on;
};
- /* SWIO: +V1.8 */
- vio_reg: vio {
- regulator-name = "vdd_1v8_gen";
+ reg_1v8_vio: vio {
+ regulator-name = "+V1.8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
@@ -529,27 +524,24 @@
/*
* EN_+V3.3 switching via FET:
- * +V3.3_AUDIO_AVDD_S, +V3.3 and +V1.8_VDD_LAN
- * see also v3_3 fixed supply
+ * +V3.3_AUDIO_AVDD_S, +V3.3
+ * see also +V3.3 fixed supply
*/
ldo2_reg: ldo2 {
- regulator-name = "en_3v3";
+ regulator-name = "EN_+V3.3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
- /* +V1.2_CSI */
ldo3_reg: ldo3 {
- regulator-name =
- "avdd_dsi_csi,pwrdet_mipi";
+ regulator-name = "+V1.2_CSI";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
- /* +V1.2_VDD_RTC */
ldo4_reg: ldo4 {
- regulator-name = "vdd_rtc";
+ regulator-name = "+V1.2_VDD_RTC";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
@@ -557,10 +549,10 @@
/*
* +V2.8_AVDD_VDAC:
- * only required for analog RGB
+ * only required for (unsupported) analog RGB
*/
ldo5_reg: ldo5 {
- regulator-name = "avdd_vdac";
+ regulator-name = "+V2.8_AVDD_VDAC";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
@@ -572,22 +564,20 @@
* granularity
*/
ldo6_reg: ldo6 {
- regulator-name = "avdd_plle";
+ regulator-name = "+V1.05_AVDD_PLLE";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
- /* +V1.2_AVDD_PLL */
ldo7_reg: ldo7 {
- regulator-name = "avdd_pll";
+ regulator-name = "+V1.2_AVDD_PLL";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
- /* +V1.0_VDD_DDR_HS */
ldo8_reg: ldo8 {
- regulator-name = "vdd_ddr_hs";
+ regulator-name = "+V1.0_VDD_DDR_HS";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
@@ -732,50 +722,40 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- avdd_hdmi_pll_1v8_reg: regulator@100 {
- compatible = "regulator-fixed";
- reg = <100>;
- regulator-name = "+V1.8_AVDD_HDMI_PLL";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- enable-active-high;
- gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
- vin-supply = <&vio_reg>;
- };
+ reg_1v8_avdd_hdmi_pll: regulator-1v8-avdd-hdmi-pll {
+ compatible = "regulator-fixed";
+ regulator-name = "+V1.8_AVDD_HDMI_PLL";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+ vin-supply = <®_1v8_vio>;
+ };
- sys_3v3_reg: regulator@101 {
- compatible = "regulator-fixed";
- reg = <101>;
- regulator-name = "3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
+ reg_3v3_avdd_hdmi: regulator-3v3-avdd-hdmi {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3_AVDD_HDMI";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+ vin-supply = <®_module_3v3>;
+ };
- avdd_hdmi_3v3_reg: regulator@102 {
- compatible = "regulator-fixed";
- reg = <102>;
- regulator-name = "+V3.3_AVDD_HDMI";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- enable-active-high;
- gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
- vin-supply = <&sys_3v3_reg>;
- };
+ reg_5v0_charge_pump: regulator-5v0-charge-pump {
+ compatible = "regulator-fixed";
+ regulator-name = "+V5.0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
- charge_pump_5v0_reg: regulator@103 {
- compatible = "regulator-fixed";
- reg = <103>;
- regulator-name = "5v0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
+ reg_module_3v3: regulator-module-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};
sound {
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Drop unused mmc1/sd1 labels.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis-eval.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 0a8900be0008..3f25bb307397 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -134,7 +134,7 @@
status = "okay";
};
- sd1: sdhci@78000000 {
+ sdhci@78000000 {
status = "okay";
bus-width = <4>;
/* SD1_CD# */
@@ -142,7 +142,7 @@
no-1-8-v;
};
- mmc1: sdhci@78000400 {
+ sdhci@78000400 {
status = "okay";
bus-width = <8>;
/* MMC1_CD# */
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Fix MMC1 cmd pin pull-up causing issues on carrier boards without
external pull-up.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 2f807d40c1b7..e749e047db7a 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -171,14 +171,14 @@
/* Apalis MMC1 */
sdmmc3_clk_pa6 {
- nvidia,pins = "sdmmc3_clk_pa6",
- "sdmmc3_cmd_pa7";
+ nvidia,pins = "sdmmc3_clk_pa6";
nvidia,function = "sdmmc3";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
sdmmc3_dat0_pb7 {
- nvidia,pins = "sdmmc3_dat0_pb7",
+ nvidia,pins = "sdmmc3_cmd_pa7",
+ "sdmmc3_dat0_pb7",
"sdmmc3_dat1_pb6",
"sdmmc3_dat2_pb5",
"sdmmc3_dat3_pb4",
--
2.14.4
From: Marcel Ziswiler <[email protected]>
White-space and newline clean-up.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- Also add two missing newlines.
arch/arm/boot/dts/tegra30-apalis-eval.dts | 5 +++--
arch/arm/boot/dts/tegra30-apalis.dtsi | 1 +
2 files changed, 4 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 3f15f327f293..0a8900be0008 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -39,6 +39,7 @@
nvidia,panel = <&panel>;
};
};
+
hdmi@54280000 {
status = "okay";
hdmi-supply = <®_5v0>;
@@ -109,6 +110,7 @@
spi@7000d400 {
status = "okay";
spi-max-frequency = <25000000>;
+
spidev0: spidev@1 {
compatible = "spidev";
reg = <1>;
@@ -120,6 +122,7 @@
spi@7000dc00 {
status = "okay";
spi-max-frequency = <25000000>;
+
spidev1: spidev@2 {
compatible = "spidev";
reg = <2>;
@@ -180,7 +183,6 @@
backlight: backlight {
compatible = "pwm-backlight";
-
/* PWM_BKL1 */
pwms = <&pwm 0 5000000>;
brightness-levels = <255 231 223 207 191 159 127 0>;
@@ -208,7 +210,6 @@
* edt,et070080dh6: EDT 7.0" LCD TFT
*/
compatible = "edt,et057090dhu", "simple-panel";
-
backlight = <&backlight>;
power-supply = <®_3v3>;
};
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 7e9d1b022982..e84feac9b992 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -39,6 +39,7 @@
pci@3,0 {
status = "okay";
nvidia,num-lanes = <1>;
+
pcie@0 {
reg = <0 0 0 0 0>;
local-mac-address = [00 00 00 00 00 00];
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Add empty local-mac-address property to be filled in by boot loader
(e.g. U-Boot).
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 69bb11c31d77..f13df31b5e25 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -34,6 +34,10 @@
pci@3,0 {
nvidia,num-lanes = <1>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ local-mac-address = [00 00 00 00 00 00];
+ };
};
};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Reorder PCIe properties.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index f13df31b5e25..fc279a073ac5 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -16,13 +16,13 @@
pcie@3000 {
avdd-pexa-supply = <&vdd2_reg>;
- vdd-pexa-supply = <&vdd2_reg>;
avdd-pexb-supply = <&vdd2_reg>;
- vdd-pexb-supply = <&vdd2_reg>;
avdd-pex-pll-supply = <&vdd2_reg>;
avdd-plle-supply = <&ldo6_reg>;
- vddio-pex-ctl-supply = <&sys_3v3_reg>;
hvdd-pex-supply = <&sys_3v3_reg>;
+ vddio-pex-ctl-supply = <&sys_3v3_reg>;
+ vdd-pexa-supply = <&vdd2_reg>;
+ vdd-pexb-supply = <&vdd2_reg>;
pci@1,0 {
nvidia,num-lanes = <4>;
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Annotate PCIe port nodes and clean-up PCIe controller/port status' with
respect to carrier board vs. module level device trees. As port 3
connects to the on-module Gigabit Ethernet MACPHY it is always enabled
together with the PCIe controller itself.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- Clean-up PCIe controller/port status' as well.
arch/arm/boot/dts/tegra30-apalis-eval.dts | 6 ------
arch/arm/boot/dts/tegra30-apalis.dtsi | 5 +++++
2 files changed, 5 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 0dc85a20bd45..e3c70e7d8d37 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -23,8 +23,6 @@
};
pcie@3000 {
- status = "okay";
-
pci@1,0 {
status = "okay";
};
@@ -32,10 +30,6 @@
pci@2,0 {
status = "okay";
};
-
- pci@3,0 {
- status = "okay";
- };
};
host1x@50000000 {
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index fc279a073ac5..c810c044025a 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -15,6 +15,7 @@
};
pcie@3000 {
+ status = "okay";
avdd-pexa-supply = <&vdd2_reg>;
avdd-pexb-supply = <&vdd2_reg>;
avdd-pex-pll-supply = <&vdd2_reg>;
@@ -24,15 +25,19 @@
vdd-pexa-supply = <&vdd2_reg>;
vdd-pexb-supply = <&vdd2_reg>;
+ /* Apalis type specific */
pci@1,0 {
nvidia,num-lanes = <4>;
};
+ /* Apalis PCIe */
pci@2,0 {
nvidia,num-lanes = <1>;
};
+ /* I210/I211 Gigabit Ethernet Controller (on-module) */
pci@3,0 {
+ status = "okay";
nvidia,num-lanes = <1>;
pcie@0 {
reg = <0 0 0 0 0>;
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Drop unused cami2c label.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis-eval.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index cd4e45759ac8..3f15f327f293 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -95,7 +95,7 @@
* CAM_I2C: I2C3_SDA/SCL on MXM3 pin 201/203 (e.g. camera sensor on
* carrier board)
*/
- cami2c: i2c@7000c500 {
+ i2c@7000c500 {
status = "okay";
clock-frequency = <400000>;
};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Reorder backlight properties.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis-eval.dts | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 9f2392a05532..300ce726ff4d 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -185,13 +185,12 @@
backlight: backlight {
compatible = "pwm-backlight";
- /* PWM_BKL1 */
- pwms = <&pwm 0 5000000>;
brightness-levels = <255 231 223 207 191 159 127 0>;
default-brightness-level = <6>;
/* BKL1_ON */
enable-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
power-supply = <®_3v3>;
+ pwms = <&pwm 0 5000000>; /* BKL1_PWM */
};
gpio-keys {
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Explicitly mux all T30 SoC balls now:
- Apalis GPIO
- Apalis HDMI1
- Apalis I2C1
- Apalis I2C2 (DDC)
- Apalis LCD1
- Apalis Parallel Camera
- Apalis SATA1_ACT#
- Apalis SPDIF1
- Apalis TS (Low-speed type specific)
- Apalis USBH_EN
- Apalis USBH_OC#
- Apalis VGA1
- on-module i210/i211 LAN control signals
- not connected and therefore disabled signals
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- Replace underscores in node names with dashes.
arch/arm/boot/dts/tegra30-apalis.dtsi | 370 ++++++++++++++++++++++++++++++++++
1 file changed, 370 insertions(+)
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index cb587670a5af..e37d22e2ceef 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -169,6 +169,68 @@
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
+ /* Apalis GPIO */
+ kb-col0-pq0 {
+ nvidia,pins = "kb_col0_pq0",
+ "kb_col1_pq1",
+ "kb_row10_ps2",
+ "kb_row11_ps3",
+ "kb_row12_ps4",
+ "kb_row13_ps5",
+ "kb_row14_ps6",
+ "kb_row15_ps7";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ /* Multiplexed and therefore disabled */
+ owr {
+ nvidia,pins = "owr";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis HDMI1 */
+ hdmi-cec-pee3 {
+ nvidia,pins = "hdmi_cec_pee3";
+ nvidia,function = "cec";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ };
+ hdmi-int-pn7 {
+ nvidia,pins = "hdmi_int_pn7";
+ nvidia,function = "hdmi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis I2C1 */
+ gen1-i2c-scl-pc4 {
+ nvidia,pins = "gen1_i2c_scl_pc4",
+ "gen1_i2c_sda_pc5";
+ nvidia,function = "i2c1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis I2C2 (DDC) */
+ ddc-scl-pv4 {
+ nvidia,pins = "ddc_scl_pv4",
+ "ddc_sda_pv5";
+ nvidia,function = "i2c4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
/* Apalis I2C3 (CAM) */
cam-i2c-scl-pbb1 {
nvidia,pins = "cam_i2c_scl_pbb1",
@@ -180,6 +242,42 @@
nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
+ /* Apalis LCD1 */
+ lcd-d0-pe0 {
+ nvidia,pins = "lcd_d0_pe0",
+ "lcd_d1_pe1",
+ "lcd_d2_pe2",
+ "lcd_d3_pe3",
+ "lcd_d4_pe4",
+ "lcd_d5_pe5",
+ "lcd_d6_pe6",
+ "lcd_d7_pe7",
+ "lcd_d8_pf0",
+ "lcd_d9_pf1",
+ "lcd_d10_pf2",
+ "lcd_d11_pf3",
+ "lcd_d12_pf4",
+ "lcd_d13_pf5",
+ "lcd_d14_pf6",
+ "lcd_d15_pf7",
+ "lcd_d16_pm0",
+ "lcd_d17_pm1",
+ "lcd_d18_pm2",
+ "lcd_d19_pm3",
+ "lcd_d20_pm4",
+ "lcd_d21_pm5",
+ "lcd_d22_pm6",
+ "lcd_d23_pm7",
+ "lcd_de_pj1",
+ "lcd_hsync_pj3",
+ "lcd_pclk_pb3",
+ "lcd_vsync_pj4";
+ nvidia,function = "displaya";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
/* Apalis MMC1 */
sdmmc3-clk-pa6 {
nvidia,pins = "sdmmc3_clk_pa6";
@@ -210,6 +308,77 @@
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
+ /* Apalis Parallel Camera */
+ cam-mclk-pcc0 {
+ nvidia,pins = "cam_mclk_pcc0";
+ nvidia,function = "vi_alt3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ vi-vsync-pd6 {
+ nvidia,pins = "vi_d0_pt4",
+ "vi_d1_pd5",
+ "vi_d2_pl0",
+ "vi_d3_pl1",
+ "vi_d4_pl2",
+ "vi_d5_pl3",
+ "vi_d6_pl4",
+ "vi_d7_pl5",
+ "vi_d8_pl6",
+ "vi_d9_pl7",
+ "vi_d10_pt2",
+ "vi_d11_pt3",
+ "vi_hsync_pd7",
+ "vi_pclk_pt0",
+ "vi_vsync_pd6";
+ nvidia,function = "vi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ /* Multiplexed and therefore disabled */
+ kb-col2-pq2 {
+ nvidia,pins = "kb_col2_pq2",
+ "kb_col3_pq3",
+ "kb_col4_pq4",
+ "kb_row4_pr4";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb-row0-pr0 {
+ nvidia,pins = "kb_row0_pr0",
+ "kb_row1_pr1",
+ "kb_row2_pr2",
+ "kb_row3_pr3";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb-row5-pr5 {
+ nvidia,pins = "kb_row5_pr5",
+ "kb_row6_pr6",
+ "kb_row7_pr7";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ /*
+ * VI level-shifter direction
+ * (pull-down => default direction input)
+ */
+ vi-mclk-pt1 {
+ nvidia,pins = "vi_mclk_pt1";
+ nvidia,function = "vi_alt3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
/* Apalis PWM1 */
pu6 {
nvidia,pins = "pu6";
@@ -250,6 +419,15 @@
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
+ /* Apalis SATA1_ACT# */
+ pex-l0-prsnt-n-pdd0 {
+ nvidia,pins = "pex_l0_prsnt_n_pdd0";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
/* Apalis SD1 */
sdmmc1-clk-pz0 {
nvidia,pins = "sdmmc1_clk_pz0";
@@ -276,6 +454,16 @@
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
+ /* Apalis SPDIF1 */
+ spdif-out-pk5 {
+ nvidia,pins = "spdif_out_pk5",
+ "spdif_in_pk6";
+ nvidia,function = "spdif";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
/* Apalis SPI1 */
spi1-sck-px5 {
nvidia,pins = "spi1_sck_px5",
@@ -298,6 +486,28 @@
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
+ /*
+ * Apalis TS (Low-speed type specific)
+ * pins may be used as GPIOs
+ */
+ kb-col5-pq5 {
+ nvidia,pins = "kb_col5_pq5";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ kb-col6-pq6 {
+ nvidia,pins = "kb_col6_pq6",
+ "kb_col7_pq7",
+ "kb_row8_ps0",
+ "kb_row9_ps1";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
/* Apalis UART1 */
ulpi-data0 {
nvidia,pins = "ulpi_data0_po1",
@@ -342,6 +552,24 @@
nvidia,tristate = <TEGRA_PIN_DISABLE>;
};
+ /* Apalis USBH_EN */
+ pex-l0-rst-n-pdd1 {
+ nvidia,pins = "pex_l0_rst_n_pdd1";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis USBH_OC# */
+ pex-l0-clkreq-n-pdd2 {
+ nvidia,pins = "pex_l0_clkreq_n_pdd2";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
/* Apalis USBO1_EN */
gen2-i2c-scl-pt5 {
nvidia,pins = "gen2_i2c_scl_pt5";
@@ -361,6 +589,16 @@
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
+ /* Apalis VGA1 not supported and therefore disabled */
+ crt-hsync-pv6 {
+ nvidia,pins = "crt_hsync_pv6",
+ "crt_vsync_pv7";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
/* Apalis WAKE1_MICO */
pv1 {
nvidia,pins = "pv1";
@@ -395,6 +633,33 @@
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
};
+ /* LAN i210/i211 DEV_OFF_N, PE_RST_N (On-module) */
+ pex-l2-prsnt-n-pdd7 {
+ nvidia,pins = "pex_l2_prsnt_n_pdd7",
+ "pex_l2_rst_n_pcc6";
+ nvidia,function = "pcie";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ /* LAN i210/i211 PE_WAKE_N, SDP3 (On-module) */
+ pex-wake-n-pdd3 {
+ nvidia,pins = "pex_wake_n_pdd3",
+ "pex_l2_clkreq_n_pcc7";
+ nvidia,function = "pcie";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ /* LAN i210/i211 SMB_ALERT_N (On-module) */
+ sys-clk-req-pz5 {
+ nvidia,pins = "sys_clk_req_pz5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
/* LVDS Transceiver Configuration */
pbb0 {
nvidia,pins = "pbb0",
@@ -417,6 +682,111 @@
nvidia,enable-input = <TEGRA_PIN_DISABLE>;
};
+ /* Not connected and therefore disabled */
+ clk-32k-out-pa0 {
+ nvidia,pins = "clk3_out_pee0",
+ "clk3_req_pee1",
+ "clk_32k_out_pa0",
+ "dap4_din_pp5",
+ "dap4_dout_pp6",
+ "dap4_fs_pp4",
+ "dap4_sclk_pp7";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap2-fs-pa2 {
+ nvidia,pins = "dap2_fs_pa2",
+ "dap2_sclk_pa3",
+ "dap2_din_pa4",
+ "dap2_dout_pa5",
+ "lcd_dc0_pn6",
+ "lcd_m1_pw1",
+ "lcd_pwr1_pc1",
+ "pex_l1_clkreq_n_pdd6",
+ "pex_l1_prsnt_n_pdd4",
+ "pex_l1_rst_n_pdd5";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gmi-ad0-pg0 {
+ nvidia,pins = "gmi_ad0_pg0",
+ "gmi_ad2_pg2",
+ "gmi_ad3_pg3",
+ "gmi_ad4_pg4",
+ "gmi_ad5_pg5",
+ "gmi_ad6_pg6",
+ "gmi_ad7_pg7",
+ "gmi_ad8_ph0",
+ "gmi_ad9_ph1",
+ "gmi_ad10_ph2",
+ "gmi_ad11_ph3",
+ "gmi_ad12_ph4",
+ "gmi_ad13_ph5",
+ "gmi_ad14_ph6",
+ "gmi_ad15_ph7",
+ "gmi_adv_n_pk0",
+ "gmi_clk_pk1",
+ "gmi_cs4_n_pk2",
+ "gmi_cs2_n_pk3",
+ "gmi_dqs_pi2",
+ "gmi_iordy_pi5",
+ "gmi_oe_n_pi1",
+ "gmi_wait_pi7",
+ "gmi_wr_n_pi0",
+ "lcd_cs1_n_pw0",
+ "pu0",
+ "pu1",
+ "pu2";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gmi-cs0-n-pj0 {
+ nvidia,pins = "gmi_cs0_n_pj0",
+ "gmi_cs1_n_pj2",
+ "gmi_cs3_n_pk4";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gmi-cs6-n-pi3 {
+ nvidia,pins = "gmi_cs6_n_pi3";
+ nvidia,function = "sata";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gmi-cs7-n-pi6 {
+ nvidia,pins = "gmi_cs7_n_pi6";
+ nvidia,function = "gmi_alt";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ lcd-pwr0-pb2 {
+ nvidia,pins = "lcd_pwr0_pb2",
+ "lcd_pwr2_pc6",
+ "lcd_wr_n_pz3";
+ nvidia,function = "hdcp";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ uart2-cts-n-pj5 {
+ nvidia,pins = "uart2_cts_n_pj5",
+ "uart2_rts_n_pj6";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
/* Power I2C (On-module) */
pwr-i2c-scl-pz6 {
nvidia,pins = "pwr_i2c_scl_pz6",
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Line break long compatible property line.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: None
arch/arm/boot/dts/tegra30-apalis-eval.dts | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 5d1bc8560dbe..97e2f1822a94 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -6,7 +6,8 @@
/ {
model = "Toradex Apalis T30 on Apalis Evaluation Board";
- compatible = "toradex,apalis_t30-eval", "toradex,apalis_t30", "nvidia,tegra30";
+ compatible = "toradex,apalis_t30-eval", "toradex,apalis_t30",
+ "nvidia,tegra30";
aliases {
rtc0 = "/i2c@7000c000/rtc@68";
--
2.14.4
From: Marcel Ziswiler <[email protected]>
The Apalis Evaluation Board uses Apalis GPIO7 on MXM3 pin 15 as reset
signal for its PLX PEX 8605 PCIe Switch.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- New patch.
arch/arm/boot/dts/tegra30-apalis-eval.dts | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index bbde98fd9712..9d9dda6c0246 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -240,3 +240,13 @@
vin-supply = <®_5v0>;
};
};
+
+&gpio {
+ /* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+ pex-perst-n {
+ gpio-hog;
+ gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PEX_PERST_N";
+ };
+};
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Rename a few nodes using more common names:
- rename tps65911@2d to pmic@2d
- rename stmpe811@41 to touchscreen@41
- rename tps62362@60 to regulator@60
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- New patch as suggested by Rob.
arch/arm/boot/dts/tegra30-apalis-eval.dts | 2 +-
arch/arm/boot/dts/tegra30-apalis.dtsi | 6 +++---
2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 9381f65a9bf5..fdfadda72e0d 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -11,7 +11,7 @@
aliases {
rtc0 = "/i2c@7000c000/rtc@68";
- rtc1 = "/i2c@7000d000/tps65911@2d";
+ rtc1 = "/i2c@7000d000/pmic@2d";
rtc2 = "/rtc@7000e000";
serial0 = &uarta;
serial1 = &uartb;
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index f15954995231..a31b112f631d 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -853,7 +853,7 @@
clocks = <&tegra_car TEGRA30_CLK_EXTERN1>;
};
- pmic: tps65911@2d {
+ pmic: pmic@2d {
compatible = "ti,tps65911";
reg = <0x2d>;
@@ -969,7 +969,7 @@
};
/* STMPE811 touch screen controller */
- stmpe811@41 {
+ touchscreen@41 {
compatible = "st,stmpe811";
reg = <0x41>;
irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
@@ -1014,7 +1014,7 @@
};
/* SW: +V1.2_VDD_CORE */
- tps62362@60 {
+ regulator@60 {
compatible = "ti,tps62362";
reg = <0x60>;
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Support the V1.1 hardware revisions with the following change:
Changed power rail for MMC1 interface to a 3.3V/1.8V switchable rail in
order to be able to run UHS SD cards in ultra high speed 1.8V mode.
[ 207.502011] mmc2: host does not support reading read-only switch,
assuming write-enable
[ 207.517011] mmc2: new ultra high speed SDR104 SDHC card at address
aaaa
[ 207.534190] mmcblk2: mmc2:aaaa SE32G 29.7 GiB
[ 207.545096] mmcblk2: p1
root@apalis-t30:~# cat /sys/kernel/debug/mmc2/ios
clock: 208000000 Hz
actual clock: 204000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 6 (sd uhs SDR104)
signal voltage: 1 (1.80 V)
driver type: 0 (driver type B)
root@apalis-t30:~# hdparm -t /dev/mmcblk2
/dev/mmcblk2:
Timing buffered disk reads: 256 MB in 3.02 seconds = 84.71 MB/sec
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- Updated V1.1 device trees with all applicable previous fixes.
Documentation/devicetree/bindings/arm/tegra.txt | 2 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts | 266 +++++
arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi | 1189 +++++++++++++++++++++++
arch/arm/boot/dts/tegra30-apalis.dtsi | 3 +-
5 files changed, 1459 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt
index 32f62bb7006d..1073a5e66122 100644
--- a/Documentation/devicetree/bindings/arm/tegra.txt
+++ b/Documentation/devicetree/bindings/arm/tegra.txt
@@ -47,6 +47,8 @@ board-specific compatible values:
nvidia,ventana
toradex,apalis_t30
toradex,apalis_t30-eval
+ toradex,apalis_t30-v1.1
+ toradex,apalis_t30-v1.1-eval
toradex,apalis-tk1
toradex,apalis-tk1-eval
toradex,colibri_t20-512
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 92dc4f05cf23..f67a87c66e9e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1072,6 +1072,7 @@ dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
tegra20-ventana.dtb
dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += \
tegra30-apalis-eval.dtb \
+ tegra30-apalis-v1.1-eval.dtb \
tegra30-beaver.dtb \
tegra30-cardhu-a02.dtb \
tegra30-cardhu-a04.dtb \
diff --git a/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts b/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
new file mode 100644
index 000000000000..0be50e881684
--- /dev/null
+++ b/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "tegra30-apalis-v1.1.dtsi"
+
+/ {
+ model = "Toradex Apalis T30 on Apalis Evaluation Board";
+ compatible = "toradex,apalis_t30-v1.1-eval", "toradex,apalis_t30-eval",
+ "toradex,apalis_t30-v1.1", "toradex,apalis_t30",
+ "nvidia,tegra30";
+
+ aliases {
+ rtc0 = "/i2c@7000c000/rtc@68";
+ rtc1 = "/i2c@7000d000/pmic@2d";
+ rtc2 = "/rtc@7000e000";
+ serial0 = &uarta;
+ serial1 = &uartb;
+ serial2 = &uartc;
+ serial3 = &uartd;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ pcie@3000 {
+ pci@1,0 {
+ status = "okay";
+ };
+
+ pci@2,0 {
+ status = "okay";
+ };
+ };
+
+ host1x@50000000 {
+ dc@54200000 {
+ rgb {
+ status = "okay";
+ nvidia,panel = <&panel>;
+ };
+ };
+
+ hdmi@54280000 {
+ status = "okay";
+ hdmi-supply = <®_5v0>;
+ };
+ };
+
+ /* Apalis UART1 */
+ serial@70006000 {
+ status = "okay";
+ };
+
+ /* Apalis UART2 */
+ serial@70006040 {
+ status = "okay";
+ };
+
+ /* Apalis UART3 */
+ serial@70006200 {
+ status = "okay";
+ };
+
+ /* Apalis UART4 */
+ serial@70006300 {
+ status = "okay";
+ };
+
+ pwm@7000a000 {
+ status = "okay";
+ };
+
+ /*
+ * GEN1_I2C: I2C1_SDA/SCL on MXM3 pin 209/211 (e.g. RTC on carrier
+ * board)
+ */
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ pcie-switch@58 {
+ compatible = "plx,pex8605";
+ reg = <0x58>;
+ };
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc@68 {
+ compatible = "st,m41t0";
+ reg = <0x68>;
+ };
+ };
+
+ /* GEN2_I2C: unused */
+
+ /*
+ * CAM_I2C: I2C3_SDA/SCL on MXM3 pin 201/203 (e.g. camera sensor on
+ * carrier board)
+ */
+ i2c@7000c500 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ /* DDC: I2C2_SDA/SCL on MXM3 pin 205/207 (e.g. display EDID) */
+ i2c@7000c700 {
+ status = "okay";
+ };
+
+ /* SPI1: Apalis SPI1 */
+ spi@7000d400 {
+ status = "okay";
+ spi-max-frequency = <25000000>;
+ };
+
+ /* SPI5: Apalis SPI2 */
+ spi@7000dc00 {
+ status = "okay";
+ spi-max-frequency = <25000000>;
+ };
+
+ /* Apalis SD1 */
+ sdhci@78000000 {
+ status = "okay";
+ bus-width = <4>;
+ /* SD1_CD# */
+ cd-gpios = <&gpio TEGRA_GPIO(CC, 5) GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ };
+
+ /* Apalis MMC1 */
+ sdhci@78000400 {
+ status = "okay";
+ bus-width = <8>;
+ /* MMC1_CD# */
+ cd-gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_LOW>;
+ vqmmc-supply = <®_vddio_sdmmc3>;
+ };
+
+ /* EHCI instance 0: USB1_DP/N -> USBO1_DP/N */
+ usb@7d000000 {
+ status = "okay";
+ dr_mode = "otg";
+ };
+
+ usb-phy@7d000000 {
+ status = "okay";
+ vbus-supply = <®_usbo1_vbus>;
+ };
+
+ /* EHCI instance 1: USB2_DP/N -> USBH2_DP/N */
+ usb@7d004000 {
+ status = "okay";
+ };
+
+ usb-phy@7d004000 {
+ status = "okay";
+ vbus-supply = <®_usbh_vbus>;
+ };
+
+ /* EHCI instance 2: USB3_DP/N -> USBH3_DP/N */
+ usb@7d008000 {
+ status = "okay";
+ };
+
+ usb-phy@7d008000 {
+ status = "okay";
+ vbus-supply = <®_usbh_vbus>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <255 231 223 207 191 159 127 0>;
+ default-brightness-level = <6>;
+ /* BKL1_ON */
+ enable-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+ power-supply = <®_3v3>;
+ pwms = <&pwm 0 5000000>; /* BKL1_PWM */
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ wakeup {
+ label = "WAKE1_MICO";
+ gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WAKEUP>;
+ debounce-interval = <10>;
+ wakeup-source;
+ };
+ };
+
+ panel: panel {
+ /*
+ * edt,et057090dhu: EDT 5.7" LCD TFT
+ * edt,et070080dh6: EDT 7.0" LCD TFT
+ */
+ compatible = "edt,et057090dhu", "simple-panel";
+ backlight = <&backlight>;
+ power-supply = <®_3v3>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3.3V_SW";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_5v0: regulator-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5V_SW";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ /* USBO1_EN */
+ reg_usbo1_vbus: regulator-usbo1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_USBO1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(T, 5) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_5v0>;
+ };
+
+ /* USBH_EN */
+ reg_usbh_vbus: regulator-usbh-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_USBH(2A|2C|2D|3|4)";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_5v0>;
+ };
+
+ /*
+ * 1.8 volt resp. 3.3 volt VDDIO_SDMMC3 depending on
+ * EN_+3.3_SDMMC3 GPIO
+ */
+ reg_vddio_sdmmc3: regulator-vddio-sdmmc3 {
+ compatible = "regulator-gpio";
+ regulator-name = "VDDIO_SDMMC3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-type = "voltage";
+ gpios = <&gpio TEGRA_GPIO(J, 5) GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0
+ 3300000 0x1>;
+ startup-delay-us = <100000>;
+ vin-supply = <&vddio_sdmmc_1v8_reg>;
+ };
+};
+
+&gpio {
+ /* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+ pex-perst-n {
+ gpio-hog;
+ gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PEX_PERST_N";
+ };
+};
diff --git a/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi b/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
new file mode 100644
index 000000000000..02f8126481a2
--- /dev/null
+++ b/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
@@ -0,0 +1,1189 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+#include "tegra30.dtsi"
+
+/*
+ * Toradex Apalis T30 Module Device Tree
+ * Compatible for Revisions 1GB: V1.1A, V1.1B; 1GB IT: V1.1A, V1.1B;
+ * 2GB: V1.1A, V1.1B
+ */
+/ {
+ memory@80000000 {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ pcie@3000 {
+ status = "okay";
+ avdd-pexa-supply = <&vdd2_reg>;
+ avdd-pexb-supply = <&vdd2_reg>;
+ avdd-pex-pll-supply = <&vdd2_reg>;
+ avdd-plle-supply = <&ldo6_reg>;
+ hvdd-pex-supply = <®_module_3v3>;
+ vddio-pex-ctl-supply = <®_module_3v3>;
+ vdd-pexa-supply = <&vdd2_reg>;
+ vdd-pexb-supply = <&vdd2_reg>;
+
+ /* Apalis type specific */
+ pci@1,0 {
+ nvidia,num-lanes = <4>;
+ };
+
+ /* Apalis PCIe */
+ pci@2,0 {
+ nvidia,num-lanes = <1>;
+ };
+
+ /* I210/I211 Gigabit Ethernet Controller (on-module) */
+ pci@3,0 {
+ status = "okay";
+ nvidia,num-lanes = <1>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ local-mac-address = [00 00 00 00 00 00];
+ };
+ };
+ };
+
+ host1x@50000000 {
+ hdmi@54280000 {
+ nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+ nvidia,hpd-gpio =
+ <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+ pll-supply = <®_1v8_avdd_hdmi_pll>;
+ vdd-supply = <®_3v3_avdd_hdmi>;
+ };
+ };
+
+ pinmux@70000868 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ /* Analogue Audio (On-module) */
+ clk1-out-pw4 {
+ nvidia,pins = "clk1_out_pw4";
+ nvidia,function = "extperiph1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap3-fs-pp0 {
+ nvidia,pins = "dap3_fs_pp0",
+ "dap3_sclk_pp3",
+ "dap3_din_pp1",
+ "dap3_dout_pp2";
+ nvidia,function = "i2s2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis BKL1_ON */
+ pv2 {
+ nvidia,pins = "pv2";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis BKL1_PWM */
+ uart3-rts-n-pc0 {
+ nvidia,pins = "uart3_rts_n_pc0";
+ nvidia,function = "pwm0";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ /* BKL1_PWM_EN#, disable TPS65911 PMIC PWM backlight */
+ uart3-cts-n-pa1 {
+ nvidia,pins = "uart3_cts_n_pa1";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis CAN1 on SPI6 */
+ spi2-cs0-n-px3 {
+ nvidia,pins = "spi2_cs0_n_px3",
+ "spi2_miso_px1",
+ "spi2_mosi_px0",
+ "spi2_sck_px2";
+ nvidia,function = "spi6";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+ /* CAN_INT1 */
+ spi2-cs1-n-pw2 {
+ nvidia,pins = "spi2_cs1_n_pw2";
+ nvidia,function = "spi3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis CAN2 on SPI4 */
+ gmi-a16-pj7 {
+ nvidia,pins = "gmi_a16_pj7",
+ "gmi_a17_pb0",
+ "gmi_a18_pb1",
+ "gmi_a19_pk7";
+ nvidia,function = "spi4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ /* CAN_INT2 */
+ spi2-cs2-n-pw3 {
+ nvidia,pins = "spi2_cs2_n_pw3";
+ nvidia,function = "spi3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis Digital Audio */
+ clk1-req-pee2 {
+ nvidia,pins = "clk1_req_pee2";
+ nvidia,function = "hda";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+ clk2-out-pw5 {
+ nvidia,pins = "clk2_out_pw5";
+ nvidia,function = "extperiph2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap1-fs-pn0 {
+ nvidia,pins = "dap1_fs_pn0",
+ "dap1_din_pn1",
+ "dap1_dout_pn2",
+ "dap1_sclk_pn3";
+ nvidia,function = "hda";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis GPIO */
+ kb-col0-pq0 {
+ nvidia,pins = "kb_col0_pq0",
+ "kb_col1_pq1",
+ "kb_row10_ps2",
+ "kb_row11_ps3",
+ "kb_row12_ps4",
+ "kb_row13_ps5",
+ "kb_row14_ps6",
+ "kb_row15_ps7";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ /* Multiplexed and therefore disabled */
+ owr {
+ nvidia,pins = "owr";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis HDMI1 */
+ hdmi-cec-pee3 {
+ nvidia,pins = "hdmi_cec_pee3";
+ nvidia,function = "cec";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ };
+ hdmi-int-pn7 {
+ nvidia,pins = "hdmi_int_pn7";
+ nvidia,function = "hdmi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis I2C1 */
+ gen1-i2c-scl-pc4 {
+ nvidia,pins = "gen1_i2c_scl_pc4",
+ "gen1_i2c_sda_pc5";
+ nvidia,function = "i2c1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis I2C2 (DDC) */
+ ddc-scl-pv4 {
+ nvidia,pins = "ddc_scl_pv4",
+ "ddc_sda_pv5";
+ nvidia,function = "i2c4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis I2C3 (CAM) */
+ cam-i2c-scl-pbb1 {
+ nvidia,pins = "cam_i2c_scl_pbb1",
+ "cam_i2c_sda_pbb2";
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis LCD1 */
+ lcd-d0-pe0 {
+ nvidia,pins = "lcd_d0_pe0",
+ "lcd_d1_pe1",
+ "lcd_d2_pe2",
+ "lcd_d3_pe3",
+ "lcd_d4_pe4",
+ "lcd_d5_pe5",
+ "lcd_d6_pe6",
+ "lcd_d7_pe7",
+ "lcd_d8_pf0",
+ "lcd_d9_pf1",
+ "lcd_d10_pf2",
+ "lcd_d11_pf3",
+ "lcd_d12_pf4",
+ "lcd_d13_pf5",
+ "lcd_d14_pf6",
+ "lcd_d15_pf7",
+ "lcd_d16_pm0",
+ "lcd_d17_pm1",
+ "lcd_d18_pm2",
+ "lcd_d19_pm3",
+ "lcd_d20_pm4",
+ "lcd_d21_pm5",
+ "lcd_d22_pm6",
+ "lcd_d23_pm7",
+ "lcd_de_pj1",
+ "lcd_hsync_pj3",
+ "lcd_pclk_pb3",
+ "lcd_vsync_pj4";
+ nvidia,function = "displaya";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis MMC1 */
+ sdmmc3-clk-pa6 {
+ nvidia,pins = "sdmmc3_clk_pa6";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+ sdmmc3-dat0-pb7 {
+ nvidia,pins = "sdmmc3_cmd_pa7",
+ "sdmmc3_dat0_pb7",
+ "sdmmc3_dat1_pb6",
+ "sdmmc3_dat2_pb5",
+ "sdmmc3_dat3_pb4",
+ "sdmmc3_dat4_pd1",
+ "sdmmc3_dat5_pd0",
+ "sdmmc3_dat6_pd3",
+ "sdmmc3_dat7_pd4";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+ /* Apalis MMC1_CD# */
+ pv3 {
+ nvidia,pins = "pv3";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis Parallel Camera */
+ cam-mclk-pcc0 {
+ nvidia,pins = "cam_mclk_pcc0";
+ nvidia,function = "vi_alt3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ vi-vsync-pd6 {
+ nvidia,pins = "vi_d0_pt4",
+ "vi_d1_pd5",
+ "vi_d2_pl0",
+ "vi_d3_pl1",
+ "vi_d4_pl2",
+ "vi_d5_pl3",
+ "vi_d6_pl4",
+ "vi_d7_pl5",
+ "vi_d8_pl6",
+ "vi_d9_pl7",
+ "vi_d10_pt2",
+ "vi_d11_pt3",
+ "vi_hsync_pd7",
+ "vi_pclk_pt0",
+ "vi_vsync_pd6";
+ nvidia,function = "vi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ /* Multiplexed and therefore disabled */
+ kb-col2-pq2 {
+ nvidia,pins = "kb_col2_pq2",
+ "kb_col3_pq3",
+ "kb_col4_pq4",
+ "kb_row4_pr4";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb-row0-pr0 {
+ nvidia,pins = "kb_row0_pr0",
+ "kb_row1_pr1",
+ "kb_row2_pr2",
+ "kb_row3_pr3";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ kb-row5-pr5 {
+ nvidia,pins = "kb_row5_pr5",
+ "kb_row6_pr6",
+ "kb_row7_pr7";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ /*
+ * VI level-shifter direction
+ * (pull-down => default direction input)
+ */
+ vi-mclk-pt1 {
+ nvidia,pins = "vi_mclk_pt1";
+ nvidia,function = "vi_alt3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis PWM1 */
+ pu6 {
+ nvidia,pins = "pu6";
+ nvidia,function = "pwm3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis PWM2 */
+ pu5 {
+ nvidia,pins = "pu5";
+ nvidia,function = "pwm2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis PWM3 */
+ pu4 {
+ nvidia,pins = "pu4";
+ nvidia,function = "pwm1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis PWM4 */
+ pu3 {
+ nvidia,pins = "pu3";
+ nvidia,function = "pwm0";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis RESET_MOCI# */
+ gmi-rst-n-pi4 {
+ nvidia,pins = "gmi_rst_n_pi4";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis SATA1_ACT# */
+ pex-l0-prsnt-n-pdd0 {
+ nvidia,pins = "pex_l0_prsnt_n_pdd0";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis SD1 */
+ sdmmc1-clk-pz0 {
+ nvidia,pins = "sdmmc1_clk_pz0";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+ sdmmc1-cmd-pz1 {
+ nvidia,pins = "sdmmc1_cmd_pz1",
+ "sdmmc1_dat0_py7",
+ "sdmmc1_dat1_py6",
+ "sdmmc1_dat2_py5",
+ "sdmmc1_dat3_py4";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+ /* Apalis SD1_CD# */
+ clk2-req-pcc5 {
+ nvidia,pins = "clk2_req_pcc5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis SPDIF1 */
+ spdif-out-pk5 {
+ nvidia,pins = "spdif_out_pk5",
+ "spdif_in_pk6";
+ nvidia,function = "spdif";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis SPI1 */
+ spi1-sck-px5 {
+ nvidia,pins = "spi1_sck_px5",
+ "spi1_mosi_px4",
+ "spi1_miso_px7",
+ "spi1_cs0_n_px6";
+ nvidia,function = "spi1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis SPI2 */
+ lcd-sck-pz4 {
+ nvidia,pins = "lcd_sck_pz4",
+ "lcd_sdout_pn5",
+ "lcd_sdin_pz2",
+ "lcd_cs0_n_pn4";
+ nvidia,function = "spi5";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /*
+ * Apalis TS (Low-speed type specific)
+ * pins may be used as GPIOs
+ */
+ kb-col5-pq5 {
+ nvidia,pins = "kb_col5_pq5";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ kb-col6-pq6 {
+ nvidia,pins = "kb_col6_pq6",
+ "kb_col7_pq7",
+ "kb_row8_ps0",
+ "kb_row9_ps1";
+ nvidia,function = "kbc";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis UART1 */
+ ulpi-data0 {
+ nvidia,pins = "ulpi_data0_po1",
+ "ulpi_data1_po2",
+ "ulpi_data2_po3",
+ "ulpi_data3_po4",
+ "ulpi_data4_po5",
+ "ulpi_data5_po6",
+ "ulpi_data6_po7",
+ "ulpi_data7_po0";
+ nvidia,function = "uarta";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis UART2 */
+ ulpi-clk-py0 {
+ nvidia,pins = "ulpi_clk_py0",
+ "ulpi_dir_py1",
+ "ulpi_nxt_py2",
+ "ulpi_stp_py3";
+ nvidia,function = "uartd";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis UART3 */
+ uart2-rxd-pc3 {
+ nvidia,pins = "uart2_rxd_pc3",
+ "uart2_txd_pc2";
+ nvidia,function = "uartb";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis UART4 */
+ uart3-rxd-pw7 {
+ nvidia,pins = "uart3_rxd_pw7",
+ "uart3_txd_pw6";
+ nvidia,function = "uartc";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis USBH_EN */
+ pex-l0-rst-n-pdd1 {
+ nvidia,pins = "pex_l0_rst_n_pdd1";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis USBH_OC# */
+ pex-l0-clkreq-n-pdd2 {
+ nvidia,pins = "pex_l0_clkreq_n_pdd2";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis USBO1_EN */
+ gen2-i2c-scl-pt5 {
+ nvidia,pins = "gen2_i2c_scl_pt5";
+ nvidia,function = "rsvd4";
+ nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis USBO1_OC# */
+ gen2-i2c-sda-pt6 {
+ nvidia,pins = "gen2_i2c_sda_pt6";
+ nvidia,function = "rsvd4";
+ nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* Apalis VGA1 not supported and therefore disabled */
+ crt-hsync-pv6 {
+ nvidia,pins = "crt_hsync_pv6",
+ "crt_vsync_pv7";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Apalis WAKE1_MICO */
+ pv1 {
+ nvidia,pins = "pv1";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* eMMC (On-module) */
+ sdmmc4-clk-pcc4 {
+ nvidia,pins = "sdmmc4_clk_pcc4",
+ "sdmmc4_cmd_pt7",
+ "sdmmc4_rst_n_pcc3";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ sdmmc4-dat0-paa0 {
+ nvidia,pins = "sdmmc4_dat0_paa0",
+ "sdmmc4_dat1_paa1",
+ "sdmmc4_dat2_paa2",
+ "sdmmc4_dat3_paa3",
+ "sdmmc4_dat4_paa4",
+ "sdmmc4_dat5_paa5",
+ "sdmmc4_dat6_paa6",
+ "sdmmc4_dat7_paa7";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* EN_+3.3_SDMMC3 */
+ uart2-cts-n-pj5 {
+ nvidia,pins = "uart2_cts_n_pj5";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* LAN i210/i211 DEV_OFF_N, PE_RST_N (On-module) */
+ pex-l2-prsnt-n-pdd7 {
+ nvidia,pins = "pex_l2_prsnt_n_pdd7",
+ "pex_l2_rst_n_pcc6";
+ nvidia,function = "pcie";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ /* LAN i210/i211 PE_WAKE_N, SDP3 (On-module) */
+ pex-wake-n-pdd3 {
+ nvidia,pins = "pex_wake_n_pdd3",
+ "pex_l2_clkreq_n_pcc7";
+ nvidia,function = "pcie";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ /* LAN i210/i211 SMB_ALERT_N (On-module) */
+ sys-clk-req-pz5 {
+ nvidia,pins = "sys_clk_req_pz5";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+
+ /* LVDS Transceiver Configuration */
+ pbb0 {
+ nvidia,pins = "pbb0",
+ "pbb7",
+ "pcc1",
+ "pcc2";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ pbb3 {
+ nvidia,pins = "pbb3",
+ "pbb4",
+ "pbb5",
+ "pbb6";
+ nvidia,function = "displayb";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Not connected and therefore disabled */
+ clk-32k-out-pa0 {
+ nvidia,pins = "clk3_out_pee0",
+ "clk3_req_pee1",
+ "clk_32k_out_pa0",
+ "dap4_din_pp5",
+ "dap4_dout_pp6",
+ "dap4_fs_pp4",
+ "dap4_sclk_pp7";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ dap2-fs-pa2 {
+ nvidia,pins = "dap2_fs_pa2",
+ "dap2_sclk_pa3",
+ "dap2_din_pa4",
+ "dap2_dout_pa5",
+ "lcd_dc0_pn6",
+ "lcd_m1_pw1",
+ "lcd_pwr1_pc1",
+ "pex_l1_clkreq_n_pdd6",
+ "pex_l1_prsnt_n_pdd4",
+ "pex_l1_rst_n_pdd5";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gmi-ad0-pg0 {
+ nvidia,pins = "gmi_ad0_pg0",
+ "gmi_ad2_pg2",
+ "gmi_ad3_pg3",
+ "gmi_ad4_pg4",
+ "gmi_ad5_pg5",
+ "gmi_ad6_pg6",
+ "gmi_ad7_pg7",
+ "gmi_ad8_ph0",
+ "gmi_ad9_ph1",
+ "gmi_ad10_ph2",
+ "gmi_ad11_ph3",
+ "gmi_ad12_ph4",
+ "gmi_ad13_ph5",
+ "gmi_ad14_ph6",
+ "gmi_ad15_ph7",
+ "gmi_adv_n_pk0",
+ "gmi_clk_pk1",
+ "gmi_cs4_n_pk2",
+ "gmi_cs2_n_pk3",
+ "gmi_dqs_pi2",
+ "gmi_iordy_pi5",
+ "gmi_oe_n_pi1",
+ "gmi_wait_pi7",
+ "gmi_wr_n_pi0",
+ "lcd_cs1_n_pw0",
+ "pu0",
+ "pu1",
+ "pu2";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gmi-cs0-n-pj0 {
+ nvidia,pins = "gmi_cs0_n_pj0",
+ "gmi_cs1_n_pj2",
+ "gmi_cs3_n_pk4";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gmi-cs6-n-pi3 {
+ nvidia,pins = "gmi_cs6_n_pi3";
+ nvidia,function = "sata";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ gmi-cs7-n-pi6 {
+ nvidia,pins = "gmi_cs7_n_pi6";
+ nvidia,function = "gmi_alt";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ lcd-pwr0-pb2 {
+ nvidia,pins = "lcd_pwr0_pb2",
+ "lcd_pwr2_pc6",
+ "lcd_wr_n_pz3";
+ nvidia,function = "hdcp";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+ uart2-rts-n-pj6 {
+ nvidia,pins = "uart2_rts_n_pj6";
+ nvidia,function = "gmi";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* Power I2C (On-module) */
+ pwr-i2c-scl-pz6 {
+ nvidia,pins = "pwr_i2c_scl_pz6",
+ "pwr_i2c_sda_pz7";
+ nvidia,function = "i2cpwr";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+ };
+
+ /*
+ * THERMD_ALERT#, unlatched I2C address pin of LM95245
+ * temperature sensor therefore requires disabling for
+ * now
+ */
+ lcd-dc1-pd2 {
+ nvidia,pins = "lcd_dc1_pd2";
+ nvidia,function = "rsvd3";
+ nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+ nvidia,tristate = <TEGRA_PIN_ENABLE>;
+ nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+ };
+
+ /* TOUCH_PEN_INT# (On-module) */
+ pv0 {
+ nvidia,pins = "pv0";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ };
+ };
+ };
+
+ serial@70006040 {
+ compatible = "nvidia,tegra30-hsuart";
+ };
+
+ serial@70006200 {
+ compatible = "nvidia,tegra30-hsuart";
+ };
+
+ serial@70006300 {
+ compatible = "nvidia,tegra30-hsuart";
+ };
+
+ hdmi_ddc: i2c@7000c700 {
+ clock-frequency = <10000>;
+ };
+
+ /*
+ * PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
+ * touch screen controller
+ */
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ /* SGTL5000 audio codec */
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_module_3v3_audio>;
+ VDDD-supply = <®_1v8_vio>;
+ VDDIO-supply = <®_module_3v3>;
+ clocks = <&tegra_car TEGRA30_CLK_EXTERN1>;
+ };
+
+ pmic: pmic@2d {
+ compatible = "ti,tps65911";
+ reg = <0x2d>;
+
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ ti,system-power-controller;
+
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ vcc1-supply = <®_module_3v3>;
+ vcc2-supply = <®_module_3v3>;
+ vcc3-supply = <®_1v8_vio>;
+ vcc4-supply = <®_module_3v3>;
+ vcc5-supply = <®_module_3v3>;
+ vcc6-supply = <®_1v8_vio>;
+ vcc7-supply = <®_5v0_charge_pump>;
+ vccio-supply = <®_module_3v3>;
+
+ regulators {
+ vdd1_reg: vdd1 {
+ regulator-name = "+V1.35_VDDIO_DDR";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+
+ vdd2_reg: vdd2 {
+ regulator-name = "+V1.05";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ vddctrl_reg: vddctrl {
+ regulator-name = "+V1.0_VDD_CPU";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ };
+
+ reg_1v8_vio: vio {
+ regulator-name = "+V1.8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ /*
+ * 1.8 volt +VDDIO_SDMMC3 in case EN_+3.3_SDMMC3
+ * is off
+ */
+ vddio_sdmmc_1v8_reg: ldo1 {
+ regulator-name = "+VDDIO_SDMMC3_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ /*
+ * EN_+V3.3 switching via FET:
+ * +V3.3_AUDIO_AVDD_S, +V3.3
+ * see also +V3.3 fixed supply
+ */
+ ldo2_reg: ldo2 {
+ regulator-name = "EN_+V3.3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-name = "+V1.2_CSI";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-name = "+V1.2_VDD_RTC";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ /*
+ * +V2.8_AVDD_VDAC:
+ * only required for (unsupported) analog RGB
+ */
+ ldo5_reg: ldo5 {
+ regulator-name = "+V2.8_AVDD_VDAC";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ /*
+ * +V1.05_AVDD_PLLE: avdd_plle should be 1.05V
+ * but LDO6 can't set voltage in 50mV
+ * granularity
+ */
+ ldo6_reg: ldo6 {
+ regulator-name = "+V1.05_AVDD_PLLE";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ ldo7_reg: ldo7 {
+ regulator-name = "+V1.2_AVDD_PLL";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ ldo8_reg: ldo8 {
+ regulator-name = "+V1.0_VDD_DDR_HS";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ /* STMPE811 touch screen controller */
+ touchscreen@41 {
+ compatible = "st,stmpe811";
+ reg = <0x41>;
+ irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ id = <0>;
+ blocks = <0x5>;
+ irq-trigger = <0x1>;
+
+ stmpe_touchscreen {
+ compatible = "st,stmpe-ts";
+ /* 3.25 MHz ADC clock speed */
+ st,adc-freq = <1>;
+ /* 8 sample average control */
+ st,ave-ctrl = <3>;
+ /* 7 length fractional part in z */
+ st,fraction-z = <7>;
+ /*
+ * 50 mA typical 80 mA max touchscreen drivers
+ * current limit value
+ */
+ st,i-drive = <1>;
+ /* 12-bit ADC */
+ st,mod-12b = <1>;
+ /* internal ADC reference */
+ st,ref-sel = <0>;
+ /* ADC converstion time: 80 clocks */
+ st,sample-time = <4>;
+ /* 1 ms panel driver settling time */
+ st,settling = <3>;
+ /* 5 ms touch detect interrupt delay */
+ st,touch-det-delay = <5>;
+ };
+ };
+
+ /*
+ * LM95245 temperature sensor
+ * Note: OVERT1# directly connected to TPS65911 PMIC PWRDN
+ */
+ temp-sensor@4c {
+ compatible = "national,lm95245";
+ reg = <0x4c>;
+ };
+
+ /* SW: +V1.2_VDD_CORE */
+ regulator@60 {
+ compatible = "ti,tps62362";
+ reg = <0x60>;
+
+ regulator-name = "tps62362-vout";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ ti,vsel0-state-low;
+ /* VSEL1: EN_CORE_DVFS_N low for DVFS */
+ ti,vsel1-state-low;
+ };
+ };
+
+ /* SPI4: CAN2 */
+ spi@7000da00 {
+ status = "okay";
+ spi-max-frequency = <10000000>;
+
+ can@1 {
+ compatible = "microchip,mcp2515";
+ reg = <1>;
+ clocks = <&clk16m>;
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
+ spi-max-frequency = <10000000>;
+ };
+ };
+
+ /* SPI6: CAN1 */
+ spi@7000de00 {
+ status = "okay";
+ spi-max-frequency = <10000000>;
+
+ can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ clocks = <&clk16m>;
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(W, 2) IRQ_TYPE_EDGE_FALLING>;
+ spi-max-frequency = <10000000>;
+ };
+ };
+
+ pmc@7000e400 {
+ nvidia,invert-interrupt;
+ nvidia,suspend-mode = <1>;
+ nvidia,cpu-pwr-good-time = <5000>;
+ nvidia,cpu-pwr-off-time = <5000>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <0>;
+ nvidia,core-power-req-active-high;
+ nvidia,sys-clock-req-active-high;
+
+ /* Set DEV_OFF bit in DCDC control register of TPS65911 PMIC */
+ i2c-thermtrip {
+ nvidia,i2c-controller-id = <4>;
+ nvidia,bus-addr = <0x2d>;
+ nvidia,reg-addr = <0x3f>;
+ nvidia,reg-data = <0x1>;
+ };
+ };
+
+ hda@70030000 {
+ status = "okay";
+ };
+
+ ahub@70080000 {
+ i2s@70080500 {
+ status = "okay";
+ };
+ };
+
+ /* eMMC */
+ sdhci@78000600 {
+ status = "okay";
+ bus-width = <8>;
+ non-removable;
+ vmmc-supply = <®_module_3v3>; /* VCC */
+ vqmmc-supply = <®_1v8_vio>; /* VCCQ */
+ mmc-ddr-1_8v;
+ };
+
+ clk32k_in: xtal1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+
+ clk16m: osc4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ };
+
+ reg_1v8_avdd_hdmi_pll: regulator-1v8-avdd-hdmi-pll {
+ compatible = "regulator-fixed";
+ regulator-name = "+V1.8_AVDD_HDMI_PLL";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+ vin-supply = <®_1v8_vio>;
+ };
+
+ reg_3v3_avdd_hdmi: regulator-3v3-avdd-hdmi {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3_AVDD_HDMI";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+ vin-supply = <®_module_3v3>;
+ };
+
+ reg_5v0_charge_pump: regulator-5v0-charge-pump {
+ compatible = "regulator-fixed";
+ regulator-name = "+V5.0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_module_3v3: regulator-module-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_module_3v3_audio: regulator-module-3v3-audio {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3_AUDIO_AVDD_S";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "toradex,tegra-audio-sgtl5000-apalis_t30",
+ "nvidia,tegra-audio-sgtl5000";
+ nvidia,model = "Toradex Apalis T30";
+ nvidia,audio-routing =
+ "Headphone Jack", "HP_OUT",
+ "LINE_IN", "Line In Jack",
+ "MIC_IN", "Mic Jack";
+ nvidia,i2s-controller = <&tegra_i2s2>;
+ nvidia,audio-codec = <&sgtl5000>;
+ clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
+ <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+ <&tegra_car TEGRA30_CLK_EXTERN1>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
+ };
+};
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index 23cecd327172..7f112f192fe9 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -3,8 +3,7 @@
/*
* Toradex Apalis T30 Module Device Tree
- * Compatible for Revisions 1GB: V1.0A, V1.1A; 1GB IT: V1.1A;
- * 2GB: V1.0B, V1.0C, V1.0E, V1.1A
+ * Compatible for Revisions 1GB: V1.0A; 2GB: V1.0B, V1.0C, V1.0E
*/
/ {
memory@80000000 {
--
2.14.4
From: Marcel Ziswiler <[email protected]>
Move the hda node from the carrier board to the module level device
tree.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- New patch.
arch/arm/boot/dts/tegra30-apalis-eval.dts | 4 ----
arch/arm/boot/dts/tegra30-apalis.dtsi | 4 ++++
2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index fdfadda72e0d..749fc6d1ff70 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -119,10 +119,6 @@
spi-max-frequency = <25000000>;
};
- hda@70030000 {
- status = "okay";
- };
-
/* Apalis SD1 */
sdhci@78000000 {
status = "okay";
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index e44b2bce6736..23cecd327172 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -1078,6 +1078,10 @@
};
};
+ hda@70030000 {
+ status = "okay";
+ };
+
ahub@70080000 {
i2s@70080500 {
status = "okay";
--
2.14.4
From: Marcel Ziswiler <[email protected]>
PLX Technology meanwhile got bought by Broadcom Corporation but the
vendor prefix plx is still used in 8 current device trees. This silences
the following checkpatch.pl warning:
WARNING: DT compatible string vendor "plx" appears un-documented
-- check ./Documentation/devicetree/bindings/vendor-prefixes.txt
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- Replace "[PATCH 27/28] ARM: tegra: apalis_t30: fix pcie switch vendor
compatible" with "[PATCH v2 26/34] dt-bindings: add broadcom (formerly
plx technology) vendor prefix" as suggested by Stefan.
Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 2c3fc512e746..e40312dcba7d 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -297,6 +297,7 @@ pine64 Pine64
pixcir PIXCIR MICROELECTRONICS Co., Ltd
plathome Plat'Home Co., Ltd.
plda PLDA
+plx Broadcom Corporation (formerly PLX Technology)
portwell Portwell Inc.
poslab Poslab Technology Co., Ltd.
powervr PowerVR (deprecated, use img)
--
2.14.4
Am 31.08.2018 um 18:38 schrieb Marcel Ziswiler:
> From: Marcel Ziswiler <[email protected]>
>
> PLX Technology meanwhile got bought by Broadcom Corporation but the
> vendor prefix plx is still used in 8 current device trees. This silences
> the following checkpatch.pl warning:
>
> WARNING: DT compatible string vendor "plx" appears un-documented
> -- check ./Documentation/devicetree/bindings/vendor-prefixes.txt
>
> Signed-off-by: Marcel Ziswiler <[email protected]>
Sounds sensible,
Reviewed-by: Andreas Färber <[email protected]>
You may want to tweak the subject though, it is slightly confusing as
Broadcom already has a vendor prefix.
Cheers,
Andreas
--
SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer, Jane Smithard, Graham Norton
HRB 21284 (AG Nürnberg)
On Fri, Aug 31, 2018 at 06:37:57PM +0200, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <[email protected]>
>
> Reorder backlight properties.
This is a bit terse. Should the header explain why too?
>
> Signed-off-by: Marcel Ziswiler <[email protected]>
>
> ---
>
> Changes in v2: None
>
> arch/arm/boot/dts/tegra30-apalis-eval.dts | 3 +--
> 1 file changed, 1 insertion(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
> index 9f2392a05532..300ce726ff4d 100644
> --- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
> +++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
> @@ -185,13 +185,12 @@
>
> backlight: backlight {
> compatible = "pwm-backlight";
> - /* PWM_BKL1 */
> - pwms = <&pwm 0 5000000>;
> brightness-levels = <255 231 223 207 191 159 127 0>;
> default-brightness-level = <6>;
> /* BKL1_ON */
> enable-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
> power-supply = <®_3v3>;
> + pwms = <&pwm 0 5000000>; /* BKL1_PWM */
> };
>
> gpio-keys {
> --
> 2.14.4
>
On Mon, 2018-09-03 at 10:22 +0100, Daniel Thompson wrote:
> On Fri, Aug 31, 2018 at 06:37:57PM +0200, Marcel Ziswiler wrote:
> > From: Marcel Ziswiler <[email protected]>
> >
> > Reorder backlight properties.
>
> This is a bit terse. Should the header explain why too?
I agree. I guess I missed mentioning it here explicitly. At other
places I did usually mentioned that it improves the situation in
regards to all our other device trees. It's just a pain to look at
various device trees if stuff is randomly ordered.
> > Signed-off-by: Marcel Ziswiler <[email protected]>
> >
> > ---
> >
> > Changes in v2: None
> >
> > arch/arm/boot/dts/tegra30-apalis-eval.dts | 3 +--
> > 1 file changed, 1 insertion(+), 2 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts
> > b/arch/arm/boot/dts/tegra30-apalis-eval.dts
> > index 9f2392a05532..300ce726ff4d 100644
> > --- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
> > +++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
> > @@ -185,13 +185,12 @@
> >
> > backlight: backlight {
> > compatible = "pwm-backlight";
> > - /* PWM_BKL1 */
> > - pwms = <&pwm 0 5000000>;
> > brightness-levels = <255 231 223 207 191 159 127
> > 0>;
> > default-brightness-level = <6>;
> > /* BKL1_ON */
> > enable-gpios = <&gpio TEGRA_GPIO(V, 2)
> > GPIO_ACTIVE_HIGH>;
> > power-supply = <®_3v3>;
> > + pwms = <&pwm 0 5000000>; /* BKL1_PWM */
> > };
> >
> > gpio-keys {
> > --
> > 2.14.4
On Fri, Aug 31, 2018 at 08:01:01PM +0200, Andreas F?rber wrote:
> Am 31.08.2018 um 18:38 schrieb Marcel Ziswiler:
> > From: Marcel Ziswiler <[email protected]>
> >
> > PLX Technology meanwhile got bought by Broadcom Corporation but the
> > vendor prefix plx is still used in 8 current device trees. This silences
> > the following checkpatch.pl warning:
> >
> > WARNING: DT compatible string vendor "plx" appears un-documented
> > -- check ./Documentation/devicetree/bindings/vendor-prefixes.txt
> >
> > Signed-off-by: Marcel Ziswiler <[email protected]>
>
> Sounds sensible,
>
> Reviewed-by: Andreas F?rber <[email protected]>
>
> You may want to tweak the subject though, it is slightly confusing as
> Broadcom already has a vendor prefix.
Yes, please.
With that,
Acked-by: Rob Herring <[email protected]>
On Fri, Aug 31, 2018 at 06:38:16PM +0200, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <[email protected]>
>
> Support the V1.1 hardware revisions with the following change:
>
> Changed power rail for MMC1 interface to a 3.3V/1.8V switchable rail in
> order to be able to run UHS SD cards in ultra high speed 1.8V mode.
>
> [ 207.502011] mmc2: host does not support reading read-only switch,
> assuming write-enable
> [ 207.517011] mmc2: new ultra high speed SDR104 SDHC card at address
> aaaa
> [ 207.534190] mmcblk2: mmc2:aaaa SE32G 29.7 GiB
> [ 207.545096] mmcblk2: p1
>
> root@apalis-t30:~# cat /sys/kernel/debug/mmc2/ios
> clock: 208000000 Hz
> actual clock: 204000000 Hz
> vdd: 21 (3.3 ~ 3.4 V)
> bus mode: 2 (push-pull)
> chip select: 0 (don't care)
> power mode: 2 (on)
> bus width: 2 (4 bits)
> timing spec: 6 (sd uhs SDR104)
> signal voltage: 1 (1.80 V)
> driver type: 0 (driver type B)
> root@apalis-t30:~# hdparm -t /dev/mmcblk2
>
> /dev/mmcblk2:
> Timing buffered disk reads: 256 MB in 3.02 seconds = 84.71 MB/sec
>
> Signed-off-by: Marcel Ziswiler <[email protected]>
>
> ---
> + panel: panel {
> + /*
> + * edt,et057090dhu: EDT 5.7" LCD TFT
> + * edt,et070080dh6: EDT 7.0" LCD TFT
> + */
> + compatible = "edt,et057090dhu", "simple-panel";
"simple-panel" is not a valid compatible string.
> + backlight = <&backlight>;
> + power-supply = <®_3v3>;
> + };
With that,
Reviewed-by: Rob Herring <[email protected]>
On Fri, Aug 31, 2018 at 06:37:42PM +0200, Marcel Ziswiler wrote:
> This series is a major overhaul and adds support for the V1.1 hardware
> revision of the Toradex Apalis T30 system on module.
>
> Changes in v2:
> - Clean-up PCIe controller/port status' as well.
> - Also move serial UART "nvidia,tegra30-hsuart" compatible to module
> level device trees.
> - Also add two missing newlines.
> - Also replace underscores in node names with dashes.
> - Explicitly disable input of BKL1_ON as well.
> - Replace underscores in node names with dashes.
> - When running some more tests I realized that the reg-addr should
> really be 0x3f. Fix this.
> - Get rid of fake clocks simple bus as suggested by Rob.
> - Replace "[PATCH 27/28] ARM: tegra: apalis_t30: fix pcie switch vendor
> compatible" with "[PATCH v2 26/34] dt-bindings: add broadcom (formerly
> plx technology) vendor prefix" as suggested by Stefan.
> - New patch as suggested by Rob.
> - New patch.
> - Drop "[PATCH 01/28] ARM: tegra: apalis_t30: enable broken-hpi on emmc"
> which should already be handled by the broken-hpi quirk as pointed out
> by Dmitry. If I would find more eMMC parts which exhibit the issue I
> will add them to the quirk as a separate patch.
> - Updated V1.1 device trees with all applicable previous fixes.
>
> Marcel Ziswiler (34):
> ARM: tegra: apalis_t30: fix mmc1 cmd pull-up
> ARM: tegra: apalis_t30: pull-up sd card detect pins
> ARM: tegra: apalis_t30: add local-mac-address property
> ARM: tegra: apalis_t30: reorder pcie properties
> ARM: tegra: apalis_t30: annotate/clean-up pcie controller/port nodes
> ARM: tegra: apalis_t30: reorder host1x/hdmi properties
> ARM: tegra: apalis_t30: regulator clean-up
> ARM: tegra: apalis_t30: add missing regulators
> ARM: tegra: apalis_t30: annotate uarts and move compatible to board
> ARM: tegra: apalis_t30: drop unused cami2c label
> ARM: tegra: apalis_t30: white-space/newline clean-up
> ARM: tegra: apalis_t30: drop unused mmc1/sd1 labels
> ARM: tegra: apalis_t30: annotate mmc1/sd1
> ARM: tegra: apalis_t30: move dr_mode property from phy to controller
> ARM: tegra: apalis_t30: reorder backlight properties
> ARM: tegra: apalis_t30: drop pwmleds
> ARM: tegra: apalis_t30: pinmux clean-up
> ARM: tegra: apalis_t30: add missing pinmux
> ARM: tegra: apalis_t30: use proper irq-gpio for stmpe811
> ARM: tegra: apalis_t30: further lm95245 temperature sensor annotation
> ARM: tegra: apalis_t30: add i2c-thermtrip
> ARM: tegra: apalis_t30: add proper emmc vmmc and vqmmc supplies
> ARM: tegra: apalis_t30: enable emmc ddr52 mode
> ARM: tegra: apalis_t30: get rid of fake clocks simple bus
> ARM: tegra: apalis_t30: line break long compatible property line
> dt-bindings: add broadcom (formerly plx technology) vendor prefix
> ARM: tegra: apalis_t30: drop module level model and compatible
> ARM: tegra: apalis_t30: drop obsolete spidev nodes
> ARM: tegra: apalis_t30: hog group for pcie switch reset gpio
> ARM: tegra: apalis_t30: rename hdmiddc to hdmi_ddc
> ARM: tegra: apalis_t30: rename tps65911@2d, stmpe811@41 and
> tps62362@60
> ARM: tegra: apalis_t30: fix mcp2515 can controller interrupt polarity
> ARM: tegra: apalis_t30: move hda node from carrier to module
> ARM: tegra: apalis_t30: support v1.1 hardware revision
>
> Documentation/devicetree/bindings/arm/tegra.txt | 2 +
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/tegra30-apalis-eval.dts | 148 +--
> arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts | 266 +++++
> arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi | 1189 ++++++++++++++++++++
> arch/arm/boot/dts/tegra30-apalis.dtsi | 705 +++++++++---
> 7 files changed, 2064 insertions(+), 248 deletions(-)
> create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
> create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
Applied, thanks.
Thierry