Changes since v1:
- merge auo,kd101n80-45a and boe,tv101wum-nl6 in one driver
This patch is based on v5.2-rc1 and these patches:
https://patchwork.kernel.org/cover/11012355/
https://patchwork.kernel.org/patch/11012345/
https://patchwork.kernel.org/patch/11012349/
Jitao Shi (2):
dt-bindings: display: panel: add auo kd101n80-45na panel bindings
drm/panel: support for auo,kd101n80-45na wuxga dsi video mode panel
.../display/panel/auo,kd101n80-45na.txt | 34 ++++++++++++++++
.../gpu/drm/panel/panel-boe-tv101wum-nl6.c | 40 +++++++++++++++++++
2 files changed, 74 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/auo,kd101n80-45na.txt
--
2.21.0
Add documentation for auo kd101n80-45na panel.
Signed-off-by: Jitao Shi <[email protected]>
Reviewed-by: Sam Ravnborg <[email protected]>
---
.../display/panel/auo,kd101n80-45na.txt | 34 +++++++++++++++++++
1 file changed, 34 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/auo,kd101n80-45na.txt
diff --git a/Documentation/devicetree/bindings/display/panel/auo,kd101n80-45na.txt b/Documentation/devicetree/bindings/display/panel/auo,kd101n80-45na.txt
new file mode 100644
index 000000000000..994c2a13f942
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/auo,kd101n80-45na.txt
@@ -0,0 +1,34 @@
+AUO Corporation 10.1" WUXGA TFT LCD panel
+
+Required properties:
+- compatible: should be "auo,kd101n80-45na"
+- reg: the virtual channel number of a DSI peripheral
+- enable-gpios: a GPIO spec for the enable pin
+- pp1800-supply: core voltage supply
+- avdd-supply: phandle of the regulator that provides positive voltage
+- avee-supply: phandle of the regulator that provides negative voltage
+- backlight: phandle of the backlight device attached to the panel
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in
+media/video-interfaces.txt. This node should describe panel's video bus.
+
+Example:
+&dsi {
+ ...
+ panel@0 {
+ compatible = "auo,kd101n80-45na";
+ reg = <0>;
+ enable-gpios = <&pio 45 0>;
+ avdd-supply = <&ppvarn_lcd>;
+ avee-supply = <&ppvarp_lcd>;
+ pp1800-supply = <&pp1800_lcd>;
+ backlight = <&backlight_lcd0>;
+ status = "okay";
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
+};
--
2.21.0
Auo,kd101n80-45na's connector is same as boe,tv101wum-nl6.
The most codes can be reuse.
So auo,kd101n80-45na and boe,tv101wum-nl6 use one driver file.
Add the different parts in driver data.
Signed-off-by: Jitao Shi <[email protected]>
---
.../gpu/drm/panel/panel-boe-tv101wum-nl6.c | 40 +++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c b/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c
index 6e06c8506623..d1ee43cfcbe2 100644
--- a/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c
+++ b/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c
@@ -372,6 +372,15 @@ static const struct panel_init_cmd boe_init_cmd[] = {
{},
};
+static const struct panel_init_cmd auo_init_cmd[] = {
+ _INIT_DELAY_CMD(24),
+ _INIT_DCS_CMD(0x11),
+ _INIT_DELAY_CMD(120),
+ _INIT_DCS_CMD(0x29),
+ _INIT_DELAY_CMD(120),
+ {},
+};
+
static inline struct boe_panel *to_boe_panel(struct drm_panel *panel)
{
return container_of(panel, struct boe_panel, base);
@@ -572,6 +581,34 @@ static const struct panel_desc boe_tv101wum_nl6_desc = {
.init_cmds = boe_init_cmd,
};
+static const struct drm_display_mode auo_default_mode = {
+ .clock = 157000,
+ .hdisplay = 1200,
+ .hsync_start = 1200 + 80,
+ .hsync_end = 1200 + 80 + 24,
+ .htotal = 1200 + 80 + 24 + 36,
+ .vdisplay = 1920,
+ .vsync_start = 1920 + 16,
+ .vsync_end = 1920 + 16 + 4,
+ .vtotal = 1920 + 16 + 4 + 16,
+ .vrefresh = 60,
+ .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+};
+
+static const struct panel_desc auo_kd101n80_45na_desc = {
+ .modes = &auo_default_mode,
+ .bpc = 8,
+ .size = {
+ .width = 216,
+ .height = 135,
+ },
+ .lanes = 4,
+ .format = MIPI_DSI_FMT_RGB888,
+ .mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
+ MIPI_DSI_MODE_LPM,
+ .init_cmds = auo_init_cmd,
+};
+
static int boe_panel_get_modes(struct drm_panel *panel)
{
struct boe_panel *boe = to_boe_panel(panel);
@@ -695,6 +732,9 @@ static const struct of_device_id boe_of_match[] = {
{ .compatible = "boe,tv101wum-nl6",
.data = &boe_tv101wum_nl6_desc
},
+ { .compatible = "auo,kd101n80-45na",
+ .data = &auo_kd101n80_45na_desc
+ },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, boe_of_match);
--
2.21.0
On Mon, Jun 24, 2019 at 4:00 PM Jitao Shi <[email protected]> wrote:
>
> Auo,kd101n80-45na's connector is same as boe,tv101wum-nl6.
> The most codes can be reuse.
> So auo,kd101n80-45na and boe,tv101wum-nl6 use one driver file.
> Add the different parts in driver data.
>
> Signed-off-by: Jitao Shi <[email protected]>
> ---
> .../gpu/drm/panel/panel-boe-tv101wum-nl6.c | 40 +++++++++++++++++++
> 1 file changed, 40 insertions(+)
>
> diff --git a/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c b/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c
> index 6e06c8506623..d1ee43cfcbe2 100644
> --- a/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c
> +++ b/drivers/gpu/drm/panel/panel-boe-tv101wum-nl6.c
> @@ -372,6 +372,15 @@ static const struct panel_init_cmd boe_init_cmd[] = {
> {},
> };
>
> +static const struct panel_init_cmd auo_init_cmd[] = {
> + _INIT_DELAY_CMD(24),
> + _INIT_DCS_CMD(0x11),
> + _INIT_DELAY_CMD(120),
> + _INIT_DCS_CMD(0x29),
> + _INIT_DELAY_CMD(120),
> + {},
> +};
> +
> static inline struct boe_panel *to_boe_panel(struct drm_panel *panel)
> {
> return container_of(panel, struct boe_panel, base);
> @@ -572,6 +581,34 @@ static const struct panel_desc boe_tv101wum_nl6_desc = {
> .init_cmds = boe_init_cmd,
> };
>
> +static const struct drm_display_mode auo_default_mode = {
> + .clock = 157000,
> + .hdisplay = 1200,
> + .hsync_start = 1200 + 80,
> + .hsync_end = 1200 + 80 + 24,
> + .htotal = 1200 + 80 + 24 + 36,
> + .vdisplay = 1920,
> + .vsync_start = 1920 + 16,
> + .vsync_end = 1920 + 16 + 4,
> + .vtotal = 1920 + 16 + 4 + 16,
> + .vrefresh = 60,
> + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
> +};
> +
> +static const struct panel_desc auo_kd101n80_45na_desc = {
> + .modes = &auo_default_mode,
> + .bpc = 8,
> + .size = {
> + .width = 216,
> + .height = 135,
Same issue as the BOE panel:
This is wrong, as this is a portrait panel, should be: width=135, height=216.
> + },
> + .lanes = 4,
> + .format = MIPI_DSI_FMT_RGB888,
> + .mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
> + MIPI_DSI_MODE_LPM,
> + .init_cmds = auo_init_cmd,
> +};
> +
> static int boe_panel_get_modes(struct drm_panel *panel)
> {
> struct boe_panel *boe = to_boe_panel(panel);
> @@ -695,6 +732,9 @@ static const struct of_device_id boe_of_match[] = {
> { .compatible = "boe,tv101wum-nl6",
> .data = &boe_tv101wum_nl6_desc
> },
> + { .compatible = "auo,kd101n80-45na",
> + .data = &auo_kd101n80_45na_desc
> + },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(of, boe_of_match);
> --
> 2.21.0
>
> _______________________________________________
> dri-devel mailing list
> [email protected]
> https://lists.freedesktop.org/mailman/listinfo/dri-devel