2019-07-31 12:46:12

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 00/20] Common patches from downstream development


This patchset holds some common changes that were never upstreamed.
With latest downstream kernel upgrade, I took the aproach to select
mainline devicetrees and atomically add missing stuff for downstream.

These patches I send here are separated out with changes that also
have a benfit for mainline.

Philippe

Changes in v2:
- Deleted touchrevolution downstream stuff
- Use generic node name
- Better comment
- Changed commit title to '...imx6qdl-apalis:...'
- Deleted touchrevolution downstream stuff
- Use generic node name
- Put a better comment in there
- Commit title
- Removed f0710a, that is downstream only
- Changed to generic node name
- Better comment

Marcel Ziswiler (1):
ARM: dts: imx7-colibri: make sure module supplies are always on

Max Krummenacher (2):
ARM: dts: imx6ull-colibri: reduce v_batt current in power off
ARM: dts: imx6ull: improve can templates

Oleksandr Suvorov (1):
ARM: dts: add recovery for I2C for iMX7

Philippe Schenker (13):
ARM: dts: imx7-colibri: prepare module device tree for FlexCAN
ARM: dts: imx7-colibri: Add sleep mode to ethernet
ARM: dts: imx7-colibri: Add touch controllers
ARM: dts: imx6qdl-colibri: add phy to fec
ARM: dts: imx6qdl-colibri: Add missing pin declaration in iomuxc
ARM: dts: imx6qdl-apalis: Add sleep state to can interfaces
ARM: dts: imx6: Add touchscreens used on Toradex eval boards
ARM: dts: imx6-colibri: Add missing pinmuxing to Toradex eval board
ARM: dts: imx6ull-colibri: Add sleep mode to fec
ARM: dts: imx6ull-colibri: Add watchdog
ARM: dts: imx6ull-colibri: Add general wakeup key used on Colibri
ARM: dts: imx6/7-colibri: switch dr_mode to otg
ARM: dts: imx6ull-colibri: Add touchscreen used with Eval Board

Stefan Agner (3):
ARM: dts: imx7-colibri: disable HS400
ARM: dts: imx7-colibri: add GPIO wakeup key
ARM: dts: imx7-colibri: fix 1.8V/UHS support

arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 39 ++++++
arch/arm/boot/dts/imx6q-apalis-eval.dts | 13 ++
arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts | 13 ++
arch/arm/boot/dts/imx6q-apalis-ixora.dts | 13 ++
arch/arm/boot/dts/imx6qdl-apalis.dtsi | 27 ++++-
arch/arm/boot/dts/imx6qdl-colibri.dtsi | 27 ++++-
.../arm/boot/dts/imx6ull-colibri-eval-v3.dtsi | 50 ++++++++
.../arm/boot/dts/imx6ull-colibri-nonwifi.dtsi | 2 +-
arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi | 2 +-
arch/arm/boot/dts/imx6ull-colibri.dtsi | 52 +++++++-
arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi | 38 ++++++
arch/arm/boot/dts/imx7-colibri.dtsi | 114 ++++++++++++++++--
12 files changed, 364 insertions(+), 26 deletions(-)

--
2.22.0


2019-07-31 12:47:15

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 02/20] ARM: dts: imx7-colibri: disable HS400

From: Stefan Agner <[email protected]>

Force HS200 by masking bit 63 of the SDHCI capability register.
The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With
that the stack checks bit 63 to descide whether HS400 is available.
Using sdhci-caps-mask allows to mask bit 63. The stack then selects
HS200 as operating mode.

This prevents rare communication errors with minimal effect on
performance:
sdhci-esdhc-imx 30b60000.usdhc: warning! HS400 strobe DLL
status REF not lock!

Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx7-colibri.dtsi | 1 +
1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index f1c1971f2160..f7c9ce5bed47 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -325,6 +325,7 @@
vmmc-supply = <&reg_module_3v3>;
vqmmc-supply = <&reg_DCDC3>;
non-removable;
+ sdhci-caps-mask = <0x80000000 0x0>;
};

&iomuxc {
--
2.22.0

2019-07-31 12:47:51

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 08/20] ARM: dts: imx7-colibri: Add touch controllers

Add atmel mxt multitouch controller and TouchRevolution multitouch
controller which are connected over an I2C bus.

Signed-off-by: Philippe Schenker <[email protected]>

---

Changes in v2:
- Deleted touchrevolution downstream stuff
- Use generic node name
- Better comment

arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi | 24 +++++++++++++++++++++
1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
index d4dbc4fc1adf..576dec9ff81c 100644
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
@@ -145,6 +145,21 @@
&i2c4 {
status = "okay";

+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiotouch>;
+ reg = <0x4a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
+ reset-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; /* SODIMM 30 */
+ status = "disabled";
+ };
+
/* M41T0M6 real time clock on carrier board */
rtc: m41t0m6@68 {
compatible = "st,m41t0";
@@ -200,3 +215,12 @@
vmmc-supply = <&reg_3v3>;
status = "okay";
};
+
+&iomuxc {
+ pinctrl_gpiotouch: touchgpios {
+ fsl,pins = <
+ MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x74
+ MX7D_PAD_GPIO1_IO10__GPIO1_IO10 0x14
+ >;
+ };
+};
--
2.22.0

2019-07-31 12:47:57

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 07/20] ARM: dts: imx7-colibri: fix 1.8V/UHS support

From: Stefan Agner <[email protected]>

Add pinmuxing and do not specify voltage restrictions in the
module level device tree.

Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx7-colibri.dtsi | 23 ++++++++++++++++++++++-
1 file changed, 22 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index 16d1a1ed1aff..67f5e0c87fdc 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -326,7 +326,6 @@
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
- no-1-8-v;
cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
disable-wp;
vqmmc-supply = <&reg_LDO2>;
@@ -671,6 +670,28 @@
>;
};

+ pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+ fsl,pins = <
+ MX7D_PAD_SD1_CMD__SD1_CMD 0x5a
+ MX7D_PAD_SD1_CLK__SD1_CLK 0x1a
+ MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5a
+ MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5a
+ MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5a
+ MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5a
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+ fsl,pins = <
+ MX7D_PAD_SD1_CMD__SD1_CMD 0x5b
+ MX7D_PAD_SD1_CLK__SD1_CLK 0x1b
+ MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5b
+ MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5b
+ MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5b
+ MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5b
+ >;
+ };
+
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX7D_PAD_SD3_CMD__SD3_CMD 0x59
--
2.22.0

2019-07-31 12:48:30

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 15/20] ARM: dts: imx6ull-colibri: reduce v_batt current in power off

From: Max Krummenacher <[email protected]>

Reduce the current drawn from VCC_BATT when the main power on the 3V3
pins to the module are switched off.

This switches off SoC internal pull resistors which are provided on the
module for TAMPER7 and TAMPER9 SoC pin and switches on a pull down
instead of a pullup for the USBC_DET module pin (TAMPER2).

Signed-off-by: Max Krummenacher <[email protected]>
Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx6ull-colibri.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/imx6ull-colibri.dtsi
index 1019ce69a242..1f112ec55e5c 100644
--- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri.dtsi
@@ -533,19 +533,19 @@

pinctrl_snvs_ad7879_int: snvs-ad7879-int-grp { /* TOUCH Interrupt */
fsl,pins = <
- MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0
+ MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x100b0
>;
};

pinctrl_snvs_reg_sd: snvs-reg-sd-grp {
fsl,pins = <
- MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x4001b8b0
+ MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x400100b0
>;
};

pinctrl_snvs_usbc_det: snvs-usbc-det-grp {
fsl,pins = <
- MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0
+ MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x130b0
>;
};

--
2.22.0

2019-07-31 12:48:56

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 19/20] ARM: dts: imx6/7-colibri: switch dr_mode to otg

In order for the otg ports, that these modules support, it is needed
that dr_mode is on otg. Switch to use that feature.

Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx6qdl-colibri.dtsi | 2 +-
arch/arm/boot/dts/imx7-colibri.dtsi | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 9a63debab0b5..6674198346d2 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -388,7 +388,7 @@
&usbotg {
pinctrl-names = "default";
disable-over-current;
- dr_mode = "peripheral";
+ dr_mode = "otg";
status = "disabled";
};

diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index 67f5e0c87fdc..42478f1aa146 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -320,7 +320,7 @@
};

&usbotg1 {
- dr_mode = "host";
+ dr_mode = "otg";
};

&usdhc1 {
--
2.22.0

2019-07-31 12:48:56

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 16/20] ARM: dts: imx6ull-colibri: Add watchdog

This patch adds the watchdog to the imx6ull-colibri devicetree

Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx6ull-colibri.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/imx6ull-colibri.dtsi
index 1f112ec55e5c..e3220298dd6f 100644
--- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri.dtsi
@@ -199,6 +199,12 @@
assigned-clock-rates = <0>, <198000000>;
};

+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
&iomuxc {
pinctrl_can_int: canint-grp {
fsl,pins = <
@@ -506,6 +512,12 @@
MX6UL_PAD_GPIO1_IO03__OSC32K_32K_OUT 0x14
>;
};
+
+ pinctrl_wdog: wdog-grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
};

&iomuxc_snvs {
--
2.22.0

2019-07-31 12:50:48

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 12/20] ARM: dts: imx6: Add touchscreens used on Toradex eval boards

This commit adds the touchscreens from Toradex so one can enable it.

Signed-off-by: Philippe Schenker <[email protected]>

---

Changes in v2:
- Deleted touchrevolution downstream stuff
- Use generic node name
- Put a better comment in there

arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 31 +++++++++++++++++++
arch/arm/boot/dts/imx6q-apalis-eval.dts | 13 ++++++++
arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts | 13 ++++++++
arch/arm/boot/dts/imx6q-apalis-ixora.dts | 13 ++++++++
4 files changed, 70 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
index 9a5d6c94cca4..763fb5e90bd3 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
@@ -168,6 +168,21 @@
&i2c3 {
status = "okay";

+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcap_1>;
+ reg = <0x4a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
+ reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; /* SODIMM 30 */
+ status = "disabled";
+ };
+
/* M41T0M6 real time clock on carrier board */
rtc_i2c: rtc@68 {
compatible = "st,m41t0";
@@ -175,6 +190,22 @@
};
};

+&iomuxc {
+ pinctrl_pcap_1: pcap-1 {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 /* SODIMM 28 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* SODIMM 30 */
+ >;
+ };
+
+ pinctrl_mxt_ts: mxt-ts {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x130b0 /* SODIMM 107 */
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x130b0 /* SODIMM 106 */
+ >;
+ };
+};
+
&ipu1_di0_disp0 {
remote-endpoint = <&lcd_display_in>;
};
diff --git a/arch/arm/boot/dts/imx6q-apalis-eval.dts b/arch/arm/boot/dts/imx6q-apalis-eval.dts
index 0edd3043d9c1..4665e15b196d 100644
--- a/arch/arm/boot/dts/imx6q-apalis-eval.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-eval.dts
@@ -167,6 +167,19 @@
&i2c1 {
status = "okay";

+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
+ status = "disabled";
+ };
+
pcie-switch@58 {
compatible = "plx,pex8605";
reg = <0x58>;
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
index b94bb687be6b..a3fa04a97d81 100644
--- a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
@@ -172,6 +172,19 @@
&i2c1 {
status = "okay";

+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
+ status = "disabled";
+ };
+
/* M41T0M6 real time clock on carrier board */
rtc_i2c: rtc@68 {
compatible = "st,m41t0";
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora.dts b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
index 302fd6adc8a7..5ba49d0f4880 100644
--- a/arch/arm/boot/dts/imx6q-apalis-ixora.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
@@ -171,6 +171,19 @@
&i2c1 {
status = "okay";

+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
+ status = "disabled";
+ };
+
eeprom@50 {
compatible = "atmel,24c02";
reg = <0x50>;
--
2.22.0

2019-07-31 12:50:55

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 11/20] ARM: dts: imx6qdl-apalis: Add sleep state to can interfaces

This patch prepares the devicetree for the new Ixora V1.2 where we are
able to turn off the supply of the can transceiver. This implies to use
a sleep state on transmission pins in order to prevent backfeeding.

Signed-off-by: Philippe Schenker <[email protected]>

---

Changes in v2:
- Changed commit title to '...imx6qdl-apalis:...'

arch/arm/boot/dts/imx6qdl-apalis.dtsi | 27 +++++++++++++++++++++------
1 file changed, 21 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
index 7c4ad541c3f5..59ed2e4a1fd1 100644
--- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
@@ -148,14 +148,16 @@
};

&can1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexcan1>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pinctrl_flexcan1_default>;
+ pinctrl-1 = <&pinctrl_flexcan1_sleep>;
status = "disabled";
};

&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexcan2>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pinctrl_flexcan2_default>;
+ pinctrl-1 = <&pinctrl_flexcan2_sleep>;
status = "disabled";
};

@@ -599,19 +601,32 @@
>;
};

- pinctrl_flexcan1: flexcan1grp {
+ pinctrl_flexcan1_default: flexcan1defgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
>;
};

- pinctrl_flexcan2: flexcan2grp {
+ pinctrl_flexcan1_sleep: flexcan1slpgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x0
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0
+ >;
+ };
+
+ pinctrl_flexcan2_default: flexcan2defgrp {
fsl,pins = <
MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0
MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
>;
};
+ pinctrl_flexcan2_sleep: flexcan2slpgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x0
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x0
+ >;
+ };

pinctrl_gpio_bl_on: gpioblon {
fsl,pins = <
--
2.22.0

2019-07-31 12:51:05

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 14/20] ARM: dts: imx6ull-colibri: Add sleep mode to fec

Do not change the clock as the power for this phy is switched
with that clock.

Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx6ull-colibri.dtsi | 18 +++++++++++++++++-
1 file changed, 17 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/imx6ull-colibri.dtsi
index d56728f03c35..1019ce69a242 100644
--- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri.dtsi
@@ -62,8 +62,9 @@
};

&fec2 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&pinctrl_enet2>;
+ pinctrl-1 = <&pinctrl_enet2_sleep>;
phy-mode = "rmii";
phy-handle = <&ethphy1>;
status = "okay";
@@ -220,6 +221,21 @@
>;
};

+ pinctrl_enet2_sleep: enet2sleepgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO06__GPIO1_IO06 0x0
+ MX6UL_PAD_GPIO1_IO07__GPIO1_IO07 0x0
+ MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x0
+ MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x0
+ MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x0
+ MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031
+ MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x0
+ MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x0
+ MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x0
+ >;
+ };
+
pinctrl_ecspi1_cs: ecspi1-cs-grp {
fsl,pins = <
MX6UL_PAD_LCD_DATA21__GPIO3_IO26 0x000a0
--
2.22.0

2019-07-31 12:51:23

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 05/20] ARM: dts: add recovery for I2C for iMX7

From: Oleksandr Suvorov <[email protected]>

- add recovery mode for applicable i2c buses for
Colibri iMX7 module.

Signed-off-by: Oleksandr Suvorov <[email protected]>
Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx7-colibri.dtsi | 25 +++++++++++++++++++++++--
1 file changed, 23 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index a8d992f3e897..2480623c92ff 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -140,8 +140,12 @@

&i2c1 {
clock-frequency = <100000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1 &pinctrl_i2c1_int>;
+ pinctrl-1 = <&pinctrl_i2c1_recovery &pinctrl_i2c1_int>;
+ scl-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+
status = "okay";

codec: sgtl5000@a {
@@ -242,8 +246,11 @@

&i2c4 {
clock-frequency = <100000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c4>;
+ pinctrl-1 = <&pinctrl_i2c4_recovery>;
+ scl-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>;
};

&lcdif {
@@ -540,6 +547,13 @@
>;
};

+ pinctrl_i2c4_recovery: i2c4-recoverygrp {
+ fsl,pins = <
+ MX7D_PAD_ENET1_RGMII_TD2__GPIO7_IO8 0x4000007f
+ MX7D_PAD_ENET1_RGMII_TD3__GPIO7_IO9 0x4000007f
+ >;
+ };
+
pinctrl_lcdif_dat: lcdif-dat-grp {
fsl,pins = <
MX7D_PAD_LCD_DATA00__LCD_DATA0 0x79
@@ -740,6 +754,13 @@
>;
};

+ pinctrl_i2c1_recovery: i2c1-recoverygrp {
+ fsl,pins = <
+ MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4 0x4000007f
+ MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5 0x4000007f
+ >;
+ };
+
pinctrl_cd_usdhc1: usdhc1-cd-grp {
fsl,pins = <
MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0 0x59 /* CD */
--
2.22.0

2019-07-31 12:51:48

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 06/20] ARM: dts: imx7-colibri: add GPIO wakeup key

From: Stefan Agner <[email protected]>

Add wakeup GPIO key which is able to wake the system from sleep
modes (e.g. Suspend-to-Memory).

Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi | 14 ++++++++++++++
arch/arm/boot/dts/imx7-colibri.dtsi | 7 ++++++-
2 files changed, 20 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
index 3f2746169181..d4dbc4fc1adf 100644
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
@@ -52,6 +52,20 @@
clock-frequency = <16000000>;
};

+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+
+ power {
+ label = "Wake-Up";
+ gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_WAKEUP>;
+ debounce-interval = <10>;
+ gpio-key,wakeup;
+ };
+ };
+
panel: panel {
compatible = "edt,et057090dhu";
backlight = <&bl>;
diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index 2480623c92ff..16d1a1ed1aff 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -741,12 +741,17 @@

pinctrl_gpio_lpsr: gpio1-grp {
fsl,pins = <
- MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1 0x59
MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2 0x59
MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3 0x59
>;
};

+ pinctrl_gpiokeys: gpiokeysgrp {
+ fsl,pins = <
+ MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1 0x19
+ >;
+ };
+
pinctrl_i2c1: i2c1-grp {
fsl,pins = <
MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA 0x4000007f
--
2.22.0

2019-07-31 12:52:29

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 01/20] ARM: dts: imx7-colibri: make sure module supplies are always on

From: Marcel Ziswiler <[email protected]>

Prevent regulators from being switched off.

Signed-off-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx7-colibri.dtsi | 2 ++
1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index 895fbde4d433..f1c1971f2160 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -54,6 +54,7 @@
regulator-name = "+V3.3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};

reg_module_3v3_avdd: regulator-module-3v3-avdd {
@@ -61,6 +62,7 @@
regulator-name = "+V3.3_AVDD_AUDIO";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};

sound {
--
2.22.0

2019-07-31 13:00:55

by Fabio Estevam

[permalink] [raw]
Subject: Re: [PATCH v2 07/20] ARM: dts: imx7-colibri: fix 1.8V/UHS support

On Wed, Jul 31, 2019 at 9:38 AM Philippe Schenker
<[email protected]> wrote:
>
> From: Stefan Agner <[email protected]>
>
> Add pinmuxing and do not specify voltage restrictions in the
> module level device tree.

It would be nice to explain the reason for doing this.

> Signed-off-by: Stefan Agner <[email protected]>
> Signed-off-by: Philippe Schenker <[email protected]>
> ---
>
> Changes in v2: None
>
> arch/arm/boot/dts/imx7-colibri.dtsi | 23 ++++++++++++++++++++++-
> 1 file changed, 22 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
> index 16d1a1ed1aff..67f5e0c87fdc 100644
> --- a/arch/arm/boot/dts/imx7-colibri.dtsi
> +++ b/arch/arm/boot/dts/imx7-colibri.dtsi
> @@ -326,7 +326,6 @@
> &usdhc1 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
> - no-1-8-v;
> cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
> disable-wp;
> vqmmc-supply = <&reg_LDO2>;
> @@ -671,6 +670,28 @@
> >;
> };
>
> + pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
> + fsl,pins = <
> + MX7D_PAD_SD1_CMD__SD1_CMD 0x5a
> + MX7D_PAD_SD1_CLK__SD1_CLK 0x1a
> + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5a
> + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5a
> + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5a
> + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5a
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
> + fsl,pins = <
> + MX7D_PAD_SD1_CMD__SD1_CMD 0x5b
> + MX7D_PAD_SD1_CLK__SD1_CLK 0x1b
> + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5b
> + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5b
> + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5b
> + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5b
> + >;
> + };

You add the entries for 100MHz and 200MHz, but I don't see them being
referenced anywhere.

2019-07-31 13:55:07

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 18/20] ARM: dts: imx6ull-colibri: Add general wakeup key used on Colibri

This adds the possibility to wake the module with an external signal
as defined in the Colibri standard

Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
index 3bee37c75aa6..d3c4809f140e 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
@@ -8,6 +8,20 @@
stdout-path = "serial0:115200n8";
};

+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+ power {
+ label = "Wake-Up";
+ gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_WAKEUP>;
+ debounce-interval = <10>;
+ wakeup-source;
+ };
+ };
+
/* fixed crystal dedicated to mcp2515 */
clk16m: clk16m {
compatible = "fixed-clock";
--
2.22.0

2019-07-31 13:55:09

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 04/20] ARM: dts: imx7-colibri: Add sleep mode to ethernet

Add sleep pinmux to the fec so it can properly sleep.

Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx7-colibri.dtsi | 19 ++++++++++++++++++-
1 file changed, 18 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index 52046085ce6f..a8d992f3e897 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -101,8 +101,9 @@
};

&fec1 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&pinctrl_enet1>;
+ pinctrl-1 = <&pinctrl_enet1_sleep>;
clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
<&clks IMX7D_ENET_AXI_ROOT_CLK>,
<&clks IMX7D_ENET1_TIME_ROOT_CLK>,
@@ -463,6 +464,22 @@
>;
};

+ pinctrl_enet1_sleep: enet1sleepgrp {
+ fsl,pins = <
+ MX7D_PAD_ENET1_RGMII_RX_CTL__GPIO7_IO4 0x0
+ MX7D_PAD_ENET1_RGMII_RD0__GPIO7_IO0 0x0
+ MX7D_PAD_ENET1_RGMII_RD1__GPIO7_IO1 0x0
+ MX7D_PAD_ENET1_RGMII_RXC__GPIO7_IO5 0x0
+
+ MX7D_PAD_ENET1_RGMII_TX_CTL__GPIO7_IO10 0x0
+ MX7D_PAD_ENET1_RGMII_TD0__GPIO7_IO6 0x0
+ MX7D_PAD_ENET1_RGMII_TD1__GPIO7_IO7 0x0
+ MX7D_PAD_GPIO1_IO12__GPIO1_IO12 0x0
+ MX7D_PAD_SD2_CD_B__GPIO5_IO9 0x0
+ MX7D_PAD_SD2_WP__GPIO5_IO10 0x0
+ >;
+ };
+
pinctrl_ecspi3_cs: ecspi3-cs-grp {
fsl,pins = <
MX7D_PAD_I2C2_SDA__GPIO4_IO11 0x14
--
2.22.0

2019-07-31 13:55:41

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 10/20] ARM: dts: imx6qdl-colibri: Add missing pin declaration in iomuxc

This adds the muxing for the optional pins usb-oc (overcurrent) and
usb-id.

Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx6qdl-colibri.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 019dda6b88ad..9a63debab0b5 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -615,6 +615,13 @@
>;
};

+ pinctrl_usbh_oc_1: usbh_oc-1 {
+ fsl,pins = <
+ /* USBH_OC */
+ MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x1b0b0
+ >;
+ };
+
pinctrl_spdif: spdifgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0
@@ -681,6 +688,13 @@
>;
};

+ pinctrl_usbc_id_1: usbc_id-1 {
+ fsl,pins = <
+ /* USBC_ID */
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+ >;
+ };
+
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071
--
2.22.0

2019-07-31 13:55:55

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 03/20] ARM: dts: imx7-colibri: prepare module device tree for FlexCAN

Prepare FlexCAN use on SODIMM 55/63 178/188. Those SODIMM pins are
compatible for CAN bus use with several modules from the Colibri
family.
Add Better drivestrength and also add flexcan2.

Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx7-colibri.dtsi | 35 ++++++++++++++++++++++++-----
1 file changed, 30 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index f7c9ce5bed47..52046085ce6f 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -117,6 +117,18 @@
fsl,magic-packet;
};

+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "disabled";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "disabled";
+};
+
&gpmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpmi_nand>;
@@ -330,12 +342,11 @@

&iomuxc {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4>;
+ pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4
+ &pinctrl_gpio7>;

pinctrl_gpio1: gpio1-grp {
fsl,pins = <
- MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3 0x74 /* SODIMM 55 */
- MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2 0x74 /* SODIMM 63 */
MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 0x14 /* SODIMM 77 */
MX7D_PAD_EPDC_DATA09__GPIO2_IO9 0x14 /* SODIMM 89 */
MX7D_PAD_EPDC_DATA08__GPIO2_IO8 0x74 /* SODIMM 91 */
@@ -416,6 +427,13 @@
>;
};

+ pinctrl_gpio7: gpio7-grp { /* Alternatively CAN1 */
+ fsl,pins = <
+ MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3 0x14 /* SODIMM 55 */
+ MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2 0x14 /* SODIMM 63 */
+ >;
+ };
+
pinctrl_i2c1_int: i2c1-int-grp { /* PMIC / TOUCH */
fsl,pins = <
MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x79
@@ -459,10 +477,17 @@
>;
};

+ pinctrl_flexcan1: flexcan1-grp {
+ fsl,pins = <
+ MX7D_PAD_ENET1_RGMII_RD3__FLEXCAN1_TX 0x79 /* SODIMM 55 */
+ MX7D_PAD_ENET1_RGMII_RD2__FLEXCAN1_RX 0x79 /* SODIMM 63 */
+ >;
+ };
+
pinctrl_flexcan2: flexcan2-grp {
fsl,pins = <
- MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX 0x59
- MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX 0x59
+ MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX 0x79 /* SODIMM 188 */
+ MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX 0x79 /* SODIMM 178 */
>;
};

--
2.22.0

2019-07-31 14:24:05

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 13/20] ARM: dts: imx6-colibri: Add missing pinmuxing to Toradex eval board

This patch adds some missing pinmuxing that is in the colibri
standard to the dts.

Signed-off-by: Philippe Schenker <[email protected]>

---

Changes in v2:
- Commit title

arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 8 ++++++++
1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
index 763fb5e90bd3..e7a2d8c3b2d4 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
@@ -191,6 +191,14 @@
};

&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_weim_gpio_1 &pinctrl_weim_gpio_2
+ &pinctrl_weim_gpio_3 &pinctrl_weim_gpio_4
+ &pinctrl_weim_gpio_5 &pinctrl_weim_gpio_6
+ &pinctrl_usbh_oc_1 &pinctrl_usbc_id_1
+ >;
+
pinctrl_pcap_1: pcap-1 {
fsl,pins = <
MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 /* SODIMM 28 */
--
2.22.0

2019-07-31 14:25:02

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 20/20] ARM: dts: imx6ull-colibri: Add touchscreen used with Eval Board

This adds the common touchscreen that is used with Toradex's
Eval Boards.

Signed-off-by: Philippe Schenker <[email protected]>

---

Changes in v2:
- Removed f0710a, that is downstream only
- Changed to generic node name
- Better comment

.../arm/boot/dts/imx6ull-colibri-eval-v3.dtsi | 24 +++++++++++++++++++
1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
index d3c4809f140e..78e74bfeca1b 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
@@ -112,6 +112,21 @@
&i2c1 {
status = "okay";

+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiotouch>;
+ reg = <0x4a>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <16 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
+ reset-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* SODIMM 30 */
+ status = "disabled";
+ };
+
/* M41T0M6 real time clock on carrier board */
m41t0m6: rtc@68 {
compatible = "st,m41t0";
@@ -188,3 +203,12 @@
sd-uhs-sdr104;
status = "okay";
};
+
+&iomuxc {
+ pinctrl_gpiotouch: touchgpios {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DQS__GPIO4_IO16 0x74
+ MX6UL_PAD_ENET1_TX_EN__GPIO2_IO05 0x14
+ >;
+ };
+};
--
2.22.0

2019-07-31 14:25:04

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 17/20] ARM: dts: imx6ull: improve can templates

From: Max Krummenacher <[email protected]>

Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan nodes to imx6ull-colibri-eval-v3.dtsi
where they belong.

Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.

Signed-off-by: Max Krummenacher <[email protected]>
Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi | 12 ++++++++++++
arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi | 2 +-
arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi | 2 +-
arch/arm/boot/dts/imx6ull-colibri.dtsi | 16 ++++++++++++++--
4 files changed, 28 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
index b6147c76d159..3bee37c75aa6 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
@@ -83,6 +83,18 @@
};
};

+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "disabled";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "disabled";
+};
+
&i2c1 {
status = "okay";

diff --git a/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi b/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
index fb213bec4654..95a11b8bcbdb 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
@@ -15,7 +15,7 @@
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
- &pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio6>;
+ &pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio6 &pinctrl_gpio7>;
};

&iomuxc_snvs {
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi b/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
index 038d8c90f6df..a0545431b3dc 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
@@ -26,7 +26,7 @@
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
- &pinctrl_gpio4 &pinctrl_gpio5>;
+ &pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio7>;

};

diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/imx6ull-colibri.dtsi
index e3220298dd6f..553d4c1f80e9 100644
--- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri.dtsi
@@ -256,6 +256,13 @@
>;
};

+ pinctrl_flexcan1: flexcan1-grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_DATA0__FLEXCAN1_TX 0x1b020
+ MX6UL_PAD_ENET1_RX_DATA1__FLEXCAN1_RX 0x1b020
+ >;
+ };
+
pinctrl_flexcan2: flexcan2-grp {
fsl,pins = <
MX6UL_PAD_ENET1_TX_DATA0__FLEXCAN2_RX 0x1b020
@@ -271,8 +278,6 @@

pinctrl_gpio1: gpio1-grp {
fsl,pins = <
- MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00 0x74 /* SODIMM 55 */
- MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01 0x74 /* SODIMM 63 */
MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25 0X14 /* SODIMM 77 */
MX6UL_PAD_JTAG_TCK__GPIO1_IO14 0x14 /* SODIMM 99 */
MX6UL_PAD_NAND_CE1_B__GPIO4_IO14 0x14 /* SODIMM 133 */
@@ -325,6 +330,13 @@
>;
};

+ pinctrl_gpio7: gpio7-grp { /* CAN1 */
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00 0x74 /* SODIMM 55 */
+ MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01 0x74 /* SODIMM 63 */
+ >;
+ };
+
pinctrl_gpmi_nand: gpmi-nand-grp {
fsl,pins = <
MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x100a9
--
2.22.0

2019-07-31 14:25:39

by Philippe Schenker

[permalink] [raw]
Subject: [PATCH v2 09/20] ARM: dts: imx6qdl-colibri: add phy to fec

Add the phy-node and mdio bus to the fec-node, represented as is on
hardware.
This commit includes micrel,led-mode that is set to the default
value, prepared for someone who wants to change this.

Signed-off-by: Philippe Schenker <[email protected]>
---

Changes in v2: None

arch/arm/boot/dts/imx6qdl-colibri.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 1beac22266ed..019dda6b88ad 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -140,7 +140,18 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rmii";
+ phy-handle = <&ethphy>;
status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@0 {
+ reg = <0>;
+ micrel,led-mode = <0>;
+ };
+ };
};

&hdmi {
--
2.22.0

2019-07-31 14:31:57

by Fabio Estevam

[permalink] [raw]
Subject: Re: [PATCH v2 08/20] ARM: dts: imx7-colibri: Add touch controllers

On Wed, Jul 31, 2019 at 9:38 AM Philippe Schenker
<[email protected]> wrote:
>
> Add atmel mxt multitouch controller and TouchRevolution multitouch

You missed to updated the commit log ;-)

2019-07-31 15:23:59

by Philippe Schenker

[permalink] [raw]
Subject: Re: [PATCH v2 07/20] ARM: dts: imx7-colibri: fix 1.8V/UHS support

On Wed, 2019-07-31 at 09:56 -0300, Fabio Estevam wrote:
> On Wed, Jul 31, 2019 at 9:38 AM Philippe Schenker
> <[email protected]> wrote:
> > From: Stefan Agner <[email protected]>
> >
> > Add pinmuxing and do not specify voltage restrictions in the
> > module level device tree.
>
> It would be nice to explain the reason for doing this.

This commit is in preparation of another patch that didn't made into this
patchset (downstream stuff in there). But I will do another patch on top that
will use this patch here. That should anyway be in mainline.

Philippe

>
> > Signed-off-by: Stefan Agner <[email protected]>
> > Signed-off-by: Philippe Schenker <[email protected]>
> > ---
> >
> > Changes in v2: None
> >
> > arch/arm/boot/dts/imx7-colibri.dtsi | 23 ++++++++++++++++++++++-
> > 1 file changed, 22 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-
> > colibri.dtsi
> > index 16d1a1ed1aff..67f5e0c87fdc 100644
> > --- a/arch/arm/boot/dts/imx7-colibri.dtsi
> > +++ b/arch/arm/boot/dts/imx7-colibri.dtsi
> > @@ -326,7 +326,6 @@
> > &usdhc1 {
> > pinctrl-names = "default";
> > pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
> > - no-1-8-v;
> > cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
> > disable-wp;
> > vqmmc-supply = <&reg_LDO2>;
> > @@ -671,6 +670,28 @@
> > >;
> > };
> >
> > + pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
> > + fsl,pins = <
> > + MX7D_PAD_SD1_CMD__SD1_CMD 0x5a
> > + MX7D_PAD_SD1_CLK__SD1_CLK 0x1a
> > + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5a
> > + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5a
> > + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5a
> > + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5a
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
> > + fsl,pins = <
> > + MX7D_PAD_SD1_CMD__SD1_CMD 0x5b
> > + MX7D_PAD_SD1_CLK__SD1_CLK 0x1b
> > + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5b
> > + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5b
> > + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5b
> > + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5b
> > + >;
> > + };
>
> You add the entries for 100MHz and 200MHz, but I don't see them being
> referenced anywhere.

2019-07-31 17:06:04

by Philippe Schenker

[permalink] [raw]
Subject: Re: [PATCH v2 08/20] ARM: dts: imx7-colibri: Add touch controllers

On Wed, 2019-07-31 at 09:42 -0300, Fabio Estevam wrote:
> On Wed, Jul 31, 2019 at 9:38 AM Philippe Schenker
> <[email protected]> wrote:
> > Add atmel mxt multitouch controller and TouchRevolution multitouch
>
> You missed to updated the commit log ;-)

Ah, shoot! :-) Thanks.

I will send a v3 then, next week.

2019-08-02 13:23:25

by Stefan Agner

[permalink] [raw]
Subject: Re: [PATCH v2 07/20] ARM: dts: imx7-colibri: fix 1.8V/UHS support

On 2019-07-31 16:52, Philippe Schenker wrote:
> On Wed, 2019-07-31 at 09:56 -0300, Fabio Estevam wrote:
>> On Wed, Jul 31, 2019 at 9:38 AM Philippe Schenker
>> <[email protected]> wrote:
>> > From: Stefan Agner <[email protected]>
>> >
>> > Add pinmuxing and do not specify voltage restrictions in the
>> > module level device tree.
>>
>> It would be nice to explain the reason for doing this.
>
> This commit is in preparation of another patch that didn't made into this
> patchset (downstream stuff in there). But I will do another patch on top that
> will use this patch here. That should anyway be in mainline.

I guess what Fabio meant here is explain this patch.

The commit message really could be improved, e.g.:

Add pinmuxing and do not specify voltage restrictions for the usdhc
instance
available on the modules edge connector. This allows to use SD-cards
with
higher transfer modes if supported by the carrier board.

--
Stefan

>
> Philippe
>
>>
>> > Signed-off-by: Stefan Agner <[email protected]>
>> > Signed-off-by: Philippe Schenker <[email protected]>
>> > ---
>> >
>> > Changes in v2: None
>> >
>> > arch/arm/boot/dts/imx7-colibri.dtsi | 23 ++++++++++++++++++++++-
>> > 1 file changed, 22 insertions(+), 1 deletion(-)
>> >
>> > diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-
>> > colibri.dtsi
>> > index 16d1a1ed1aff..67f5e0c87fdc 100644
>> > --- a/arch/arm/boot/dts/imx7-colibri.dtsi
>> > +++ b/arch/arm/boot/dts/imx7-colibri.dtsi
>> > @@ -326,7 +326,6 @@
>> > &usdhc1 {
>> > pinctrl-names = "default";
>> > pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
>> > - no-1-8-v;
>> > cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
>> > disable-wp;
>> > vqmmc-supply = <&reg_LDO2>;
>> > @@ -671,6 +670,28 @@
>> > >;
>> > };
>> >
>> > + pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
>> > + fsl,pins = <
>> > + MX7D_PAD_SD1_CMD__SD1_CMD 0x5a
>> > + MX7D_PAD_SD1_CLK__SD1_CLK 0x1a
>> > + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5a
>> > + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5a
>> > + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5a
>> > + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5a
>> > + >;
>> > + };
>> > +
>> > + pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
>> > + fsl,pins = <
>> > + MX7D_PAD_SD1_CMD__SD1_CMD 0x5b
>> > + MX7D_PAD_SD1_CLK__SD1_CLK 0x1b
>> > + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5b
>> > + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5b
>> > + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5b
>> > + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5b
>> > + >;
>> > + };
>>
>> You add the entries for 100MHz and 200MHz, but I don't see them being
>> referenced anywhere.

2019-08-05 07:20:33

by Philippe Schenker

[permalink] [raw]
Subject: Re: [PATCH v2 07/20] ARM: dts: imx7-colibri: fix 1.8V/UHS support

On Fri, 2019-08-02 at 10:51 +0200, Stefan Agner wrote:
> On 2019-07-31 16:52, Philippe Schenker wrote:
> > On Wed, 2019-07-31 at 09:56 -0300, Fabio Estevam wrote:
> > > On Wed, Jul 31, 2019 at 9:38 AM Philippe Schenker
> > > <[email protected]> wrote:
> > > > From: Stefan Agner <[email protected]>
> > > >
> > > > Add pinmuxing and do not specify voltage restrictions in the
> > > > module level device tree.
> > >
> > > It would be nice to explain the reason for doing this.
> >
> > This commit is in preparation of another patch that didn't made into this
> > patchset (downstream stuff in there). But I will do another patch on top
> > that
> > will use this patch here. That should anyway be in mainline.
>
> I guess what Fabio meant here is explain this patch.
>
> The commit message really could be improved, e.g.:
>
> Add pinmuxing and do not specify voltage restrictions for the usdhc
> instance
> available on the modules edge connector. This allows to use SD-cards
> with
> higher transfer modes if supported by the carrier board.
>
> --
> Stefan

Ah, sorry Fabio. I indeed understood you wrong and thanks Stefan for clarifying.
I have the new message in for v3.

Philippe

>
> > Philippe
> >
> > > > Signed-off-by: Stefan Agner <[email protected]>
> > > > Signed-off-by: Philippe Schenker <[email protected]>
> > > > ---
> > > >
> > > > Changes in v2: None
> > > >
> > > > arch/arm/boot/dts/imx7-colibri.dtsi | 23 ++++++++++++++++++++++-
> > > > 1 file changed, 22 insertions(+), 1 deletion(-)
> > > >
> > > > diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi
> > > > b/arch/arm/boot/dts/imx7-
> > > > colibri.dtsi
> > > > index 16d1a1ed1aff..67f5e0c87fdc 100644
> > > > --- a/arch/arm/boot/dts/imx7-colibri.dtsi
> > > > +++ b/arch/arm/boot/dts/imx7-colibri.dtsi
> > > > @@ -326,7 +326,6 @@
> > > > &usdhc1 {
> > > > pinctrl-names = "default";
> > > > pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
> > > > - no-1-8-v;
> > > > cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
> > > > disable-wp;
> > > > vqmmc-supply = <&reg_LDO2>;
> > > > @@ -671,6 +670,28 @@
> > > > >;
> > > > };
> > > >
> > > > + pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
> > > > + fsl,pins = <
> > > > + MX7D_PAD_SD1_CMD__SD1_CMD 0x5a
> > > > + MX7D_PAD_SD1_CLK__SD1_CLK 0x1a
> > > > + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5a
> > > > + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5a
> > > > + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5a
> > > > + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5a
> > > > + >;
> > > > + };
> > > > +
> > > > + pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
> > > > + fsl,pins = <
> > > > + MX7D_PAD_SD1_CMD__SD1_CMD 0x5b
> > > > + MX7D_PAD_SD1_CLK__SD1_CLK 0x1b
> > > > + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x5b
> > > > + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x5b
> > > > + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x5b
> > > > + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x5b
> > > > + >;
> > > > + };
> > >
> > > You add the entries for 100MHz and 200MHz, but I don't see them being
> > > referenced anywhere.