From: Marcel Ziswiler <[email protected]>
Fix typo in top-level module compatible.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2: New patch.
arch/arm/boot/dts/vf500-colibri.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/vf500-colibri.dtsi b/arch/arm/boot/dts/vf500-colibri.dtsi
index 237b0246fa84..92255f8893ce 100644
--- a/arch/arm/boot/dts/vf500-colibri.dtsi
+++ b/arch/arm/boot/dts/vf500-colibri.dtsi
@@ -44,7 +44,7 @@
/ {
model = "Toradex Colibri VF50 COM";
- compatible = "toradex,vf610-colibri_vf50", "fsl,vf500";
+ compatible = "toradex,vf500-colibri_vf50", "fsl,vf500";
memory@80000000 {
device_type = "memory";
--
2.21.0
From: Marcel Ziswiler <[email protected]>
This patch adds the device tree to support Toradex Colibri iMX8X a
computer on module which can be used on different carrier boards.
The module consists of an NXP i.MX 8X family SoC (either i.MX 8DualX or
8QuadXPlus), a PF8100 PMIC, a FastEthernet PHY, 1 or 2 GB of LPDDR4
RAM, some level shifters, a Micron eMMC, a USB hub, an AD7879 resistive
touch controller, an SGTL5000 audio codec and on-module CSI as well as
DSI-LVDS FFC receptacles plus an optional Bluetooth/Wi-Fi module.
Anything that is not self-contained on the module is disabled by
default.
The device tree for the Colibri Evaluation Board includes the module's
device tree and enables the supported peripherals of the carrier board
(the Colibri Evaluation Board supports almost all of them).
So far there is no display or USB functionality supported at all but
basic console UART, eMMC and Ethernet functionality work fine.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
---
Changes in v2:
- Replace X11 with identical MIT license as suggested by Shawn.
- Use proper generic binding for GPIO wake-up key as suggested by Shawn.
- Sort devicetree label nodes alphabetically as suggested by Shawn.
- Use generic touch controller node names as suggested by Shawn.
- Put iomuxc at end of the file to improve the readability, as suggested
by Shawn.
- Drop unneeded colibri-imx8qxp iomuxc container node.
- Name pinctrl nodes more consistently and sort them alphabetically as
suggested by Shawn.
- Enable possibility for GPIO key to act as a wake-up curtsey Philippe.
- Fix pull mode for wake-up GPIO pin curtsey Oleksandr.
- Add pinctrl for optional FlexCAN3 curtsey Oleksandr.
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8qxp-colibri-eval-v3.dts | 15 +
.../freescale/imx8qxp-colibri-eval-v3.dtsi | 62 ++
.../boot/dts/freescale/imx8qxp-colibri.dtsi | 598 ++++++++++++++++++
4 files changed, 676 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 93fce8f0c66d..bd3764e52cfd 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -31,4 +31,5 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-eval-v3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dts b/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dts
new file mode 100644
index 000000000000..6b21a295c126
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2019 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8qxp-colibri.dtsi"
+#include "imx8qxp-colibri-eval-v3.dtsi"
+
+/ {
+ model = "Toradex Colibri iMX8QXP/DX on Colibri Evaluation Board V3";
+ compatible = "toradex,colibri-imx8x-eval-v3",
+ "toradex,colibri-imx8x", "fsl,imx8qxp";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi
new file mode 100644
index 000000000000..c7336f387605
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2019 Toradex
+ */
+
+#include "dt-bindings/input/linux-event-codes.h"
+
+/ {
+ aliases {
+ rtc0 = &rtc_i2c;
+ rtc1 = &rtc;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+
+ wakeup {
+ label = "Wake-Up";
+ gpios = <&lsio_gpio3 10 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_WAKEUP>;
+ debounce-interval = <10>;
+ wakeup-source;
+ };
+ };
+};
+
+&adma_i2c1 {
+ status = "okay";
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc_i2c: rtc@68 {
+ compatible = "st,m41t0";
+ reg = <0x68>;
+ };
+};
+
+/* Colibri UART_B */
+&adma_lpuart0 {
+ status= "okay";
+};
+
+/* Colibri UART_C */
+&adma_lpuart2 {
+ status= "okay";
+};
+
+/* Colibri UART_A */
+&adma_lpuart3 {
+ status= "okay";
+};
+
+/* Colibri FastEthernet */
+&fec1 {
+ status = "okay";
+};
+
+/* Colibri SD/MMC Card */
+&usdhc2 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi
new file mode 100644
index 000000000000..75f17a29f81e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi
@@ -0,0 +1,598 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2019 Toradex
+ */
+
+#include "imx8qxp.dtsi"
+
+/ {
+ model = "Toradex Colibri iMX8QXP/DX Module";
+ compatible = "toradex,colibri-imx8x", "fsl,imx8qxp";
+
+ chosen {
+ stdout-path = &adma_lpuart3;
+ };
+
+ reg_module_3v3: regulator-module-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "+V3.3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+/* On-module I2C */
+&adma_i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>, <&pinctrl_sgtl5000_usb_clk>;
+ status = "okay";
+
+ /* Touch controller */
+ touchscreen@2c {
+ compatible = "adi,ad7879-1";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ad7879_int>;
+ reg = <0x2c>;
+ interrupt-parent = <&lsio_gpio3>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-max-pressure = <4096>;
+ adi,resistance-plate-x = <120>;
+ adi,first-conversion-delay = /bits/ 8 <3>;
+ adi,acquisition-time = /bits/ 8 <1>;
+ adi,median-filter-size = /bits/ 8 <2>;
+ adi,averaging = /bits/ 8 <1>;
+ adi,conversion-interval = /bits/ 8 <255>;
+ };
+};
+
+/* Colibri I2C */
+&adma_i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+};
+
+/* Colibri UART_B */
+&adma_lpuart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart0>;
+};
+
+/* Colibri UART_C */
+&adma_lpuart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart2>;
+};
+
+/* Colibri UART_A */
+&adma_lpuart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart3>, <&pinctrl_lpuart3_ctrl>;
+};
+
+/* Colibri FastEthernet */
+&fec1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pinctrl_fec1>;
+ pinctrl-1 = <&pinctrl_fec1_sleep>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ max-speed = <100>;
+ reg = <2>;
+ };
+ };
+};
+
+/* On-module eMMC */
+&usdhc1 {
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ status = "okay";
+};
+
+/* Colibri SD/MMC Card */
+&usdhc2 {
+ bus-width = <4>;
+ cd-gpios = <&lsio_gpio3 9 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_module_3v3>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_gpio_sleep>;
+ disable-wp;
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ext_io0>, <&pinctrl_hog0>, <&pinctrl_hog1>;
+
+ /* On-module touch pen-down interrupt */
+ pinctrl_ad7879_int: ad7879intgrp {
+ fsl,pins = <
+ IMX8QXP_MIPI_CSI0_I2C0_SCL_LSIO_GPIO3_IO05 0x21
+ >;
+ };
+
+ /* Colibri Analogue Inputs */
+ pinctrl_adc0: adc0grp {
+ fsl,pins = <
+ IMX8QXP_ADC_IN0_ADMA_ADC_IN0 0x60 /* SODIMM 8 */
+ IMX8QXP_ADC_IN1_ADMA_ADC_IN1 0x60 /* SODIMM 6 */
+ IMX8QXP_ADC_IN4_ADMA_ADC_IN4 0x60 /* SODIMM 4 */
+ IMX8QXP_ADC_IN5_ADMA_ADC_IN5 0x60 /* SODIMM 2 */
+ >;
+ };
+
+ pinctrl_can_int: canintgrp {
+ fsl,pins = <
+ IMX8QXP_QSPI0A_DQS_LSIO_GPIO3_IO13 0x40 /* SODIMM 73 */
+ >;
+ };
+
+ pinctrl_csi_ctl: csictlgrp {
+ fsl,pins = <
+ IMX8QXP_QSPI0A_SS0_B_LSIO_GPIO3_IO14 0x20 /* SODIMM 77 */
+ IMX8QXP_QSPI0A_SS1_B_LSIO_GPIO3_IO15 0x20 /* SODIMM 89 */
+ >;
+ };
+
+ pinctrl_ext_io0: extio0grp {
+ fsl,pins = <
+ IMX8QXP_ENET0_RGMII_RXD3_LSIO_GPIO5_IO08 0x06000040 /* SODIMM 135 */
+ >;
+ };
+
+ /* Colibri Ethernet: On-module 100Mbps PHY Micrel KSZ8041 */
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ IMX8QXP_ENET0_MDC_CONN_ENET0_MDC 0x06000020
+ IMX8QXP_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020
+ IMX8QXP_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x61
+ IMX8QXP_ENET0_RGMII_TXC_CONN_ENET0_RCLK50M_OUT 0x06000061
+ IMX8QXP_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x61
+ IMX8QXP_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x61
+ IMX8QXP_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x61
+ IMX8QXP_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x61
+ IMX8QXP_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x61
+ IMX8QXP_ENET0_RGMII_RXD2_CONN_ENET0_RMII_RX_ER 0x61
+ >;
+ };
+
+ pinctrl_fec1_sleep: fec1slpgrp {
+ fsl,pins = <
+ IMX8QXP_ENET0_MDC_LSIO_GPIO5_IO11 0x06000041
+ IMX8QXP_ENET0_MDIO_LSIO_GPIO5_IO10 0x06000041
+ IMX8QXP_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30 0x41
+ IMX8QXP_ENET0_RGMII_TXC_LSIO_GPIO4_IO29 0x41
+ IMX8QXP_ENET0_RGMII_TXD0_LSIO_GPIO4_IO31 0x41
+ IMX8QXP_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00 0x41
+ IMX8QXP_ENET0_RGMII_RX_CTL_LSIO_GPIO5_IO04 0x41
+ IMX8QXP_ENET0_RGMII_RXD0_LSIO_GPIO5_IO05 0x41
+ IMX8QXP_ENET0_RGMII_RXD1_LSIO_GPIO5_IO06 0x41
+ IMX8QXP_ENET0_RGMII_RXD2_LSIO_GPIO5_IO07 0x41
+ >;
+ };
+
+ /* Colibri optional CAN on UART_B RTS/CTS */
+ pinctrl_flexcan1: flexcan0grp {
+ fsl,pins = <
+ IMX8QXP_FLEXCAN0_TX_ADMA_FLEXCAN0_TX 0x21 /* SODIMM 32 */
+ IMX8QXP_FLEXCAN0_RX_ADMA_FLEXCAN0_RX 0x21 /* SODIMM 34 */
+ >;
+ };
+
+ /* Colibri optional CAN on PS2 */
+ pinctrl_flexcan2: flexcan1grp {
+ fsl,pins = <
+ IMX8QXP_FLEXCAN1_TX_ADMA_FLEXCAN1_TX 0x21 /* SODIMM 55 */
+ IMX8QXP_FLEXCAN1_RX_ADMA_FLEXCAN1_RX 0x21 /* SODIMM 63 */
+ >;
+ };
+
+ /* Colibri optional CAN on UART_A TXD/RXD */
+ pinctrl_flexcan3: flexcan2grp {
+ fsl,pins = <
+ IMX8QXP_FLEXCAN2_TX_ADMA_FLEXCAN2_TX 0x21 /* SODIMM 35 */
+ IMX8QXP_FLEXCAN2_RX_ADMA_FLEXCAN2_RX 0x21 /* SODIMM 33 */
+ >;
+ };
+
+ /* Colibri LCD Back-Light GPIO */
+ pinctrl_gpio_bl_on: gpioblongrp {
+ fsl,pins = <
+ IMX8QXP_QSPI0A_DATA3_LSIO_GPIO3_IO12 0x60 /* SODIMM 71 */
+ >;
+ };
+
+ pinctrl_gpiokeys: gpiokeysgrp {
+ fsl,pins = <
+ IMX8QXP_QSPI0A_DATA1_LSIO_GPIO3_IO10 0x06700041 /* SODIMM 45 */
+ >;
+ };
+
+ pinctrl_hog0: hog0grp {
+ fsl,pins = <
+ IMX8QXP_ENET0_RGMII_TXD3_LSIO_GPIO5_IO02 0x06000020 /* SODIMM 65 */
+ IMX8QXP_CSI_D07_CI_PI_D09 0x61 /* SODIMM 65 */
+ IMX8QXP_QSPI0A_DATA2_LSIO_GPIO3_IO11 0x20 /* SODIMM 69 */
+ IMX8QXP_SAI0_TXC_LSIO_GPIO0_IO26 0x20 /* SODIMM 79 */
+ IMX8QXP_CSI_D02_CI_PI_D04 0x61 /* SODIMM 79 */
+ IMX8QXP_ENET0_RGMII_RXC_LSIO_GPIO5_IO03 0x06000020 /* SODIMM 85 */
+ IMX8QXP_CSI_D06_CI_PI_D08 0x61 /* SODIMM 85 */
+ IMX8QXP_QSPI0B_SCLK_LSIO_GPIO3_IO17 0x20 /* SODIMM 95 */
+ IMX8QXP_SAI0_RXD_LSIO_GPIO0_IO27 0x20 /* SODIMM 97 */
+ IMX8QXP_CSI_D03_CI_PI_D05 0x61 /* SODIMM 97 */
+ IMX8QXP_QSPI0B_DATA0_LSIO_GPIO3_IO18 0x20 /* SODIMM 99 */
+ IMX8QXP_SAI0_TXFS_LSIO_GPIO0_IO28 0x20 /* SODIMM 101 */
+ IMX8QXP_CSI_D00_CI_PI_D02 0x61 /* SODIMM 101 */
+ IMX8QXP_SAI0_TXD_LSIO_GPIO0_IO25 0x20 /* SODIMM 103 */
+ IMX8QXP_CSI_D01_CI_PI_D03 0x61 /* SODIMM 103 */
+ IMX8QXP_QSPI0B_DATA1_LSIO_GPIO3_IO19 0x20 /* SODIMM 105 */
+ IMX8QXP_QSPI0B_DATA2_LSIO_GPIO3_IO20 0x20 /* SODIMM 107 */
+ IMX8QXP_USB_SS3_TC2_LSIO_GPIO4_IO05 0x20 /* SODIMM 127 */
+ IMX8QXP_USB_SS3_TC3_LSIO_GPIO4_IO06 0x20 /* SODIMM 131 */
+ IMX8QXP_USB_SS3_TC1_LSIO_GPIO4_IO04 0x20 /* SODIMM 133 */
+ IMX8QXP_CSI_PCLK_LSIO_GPIO3_IO00 0x20 /* SODIMM 96 */
+ IMX8QXP_QSPI0B_DATA3_LSIO_GPIO3_IO21 0x20 /* SODIMM 98 */
+ IMX8QXP_SAI1_RXFS_LSIO_GPIO0_IO31 0x20 /* SODIMM 100 */
+ IMX8QXP_QSPI0B_DQS_LSIO_GPIO3_IO22 0x20 /* SODIMM 102 */
+ IMX8QXP_QSPI0B_SS0_B_LSIO_GPIO3_IO23 0x20 /* SODIMM 104 */
+ IMX8QXP_QSPI0B_SS1_B_LSIO_GPIO3_IO24 0x20 /* SODIMM 106 */
+ >;
+ };
+
+ pinctrl_hog1: hog1grp {
+ fsl,pins = <
+ IMX8QXP_CSI_MCLK_LSIO_GPIO3_IO01 0x20 /* SODIMM 75 */
+ IMX8QXP_QSPI0A_SCLK_LSIO_GPIO3_IO16 0x20 /* SODIMM 93 */
+ >;
+ };
+
+ /*
+ * This pin is used in the SCFW as a UART. Using it from
+ * Linux would require rewritting the SCFW board file.
+ */
+ pinctrl_hog_scfw: hogscfwgrp {
+ fsl,pins = <
+ IMX8QXP_SCU_GPIO0_00_LSIO_GPIO2_IO03 0x20 /* SODIMM 144 */
+ >;
+ };
+
+ /* On Module I2C */
+ pinctrl_i2c0: i2c0grp {
+ fsl,pins = <
+ IMX8QXP_MIPI_CSI0_GPIO0_00_ADMA_I2C0_SCL 0x06000021
+ IMX8QXP_MIPI_CSI0_GPIO0_01_ADMA_I2C0_SDA 0x06000021
+ >;
+ };
+
+ /* MIPI DSI I2C accessible on SODIMM (X1) and FFC (X2) */
+ pinctrl_i2c0_mipi_lvds0: i2c0mipilvds0grp {
+ fsl,pins = <
+ IMX8QXP_MIPI_DSI0_I2C0_SCL_MIPI_DSI0_I2C0_SCL 0xc6000020 /* SODIMM 140 */
+ IMX8QXP_MIPI_DSI0_I2C0_SDA_MIPI_DSI0_I2C0_SDA 0xc6000020 /* SODIMM 142 */
+ >;
+ };
+
+ /* MIPI CSI I2C accessible on SODIMM (X1) and FFC (X3) */
+ pinctrl_i2c0_mipi_lvds1: i2c0mipilvds1grp {
+ fsl,pins = <
+ IMX8QXP_MIPI_DSI1_I2C0_SCL_MIPI_DSI1_I2C0_SCL 0xc6000020 /* SODIMM 186 */
+ IMX8QXP_MIPI_DSI1_I2C0_SDA_MIPI_DSI1_I2C0_SDA 0xc6000020 /* SODIMM 188 */
+ >;
+ };
+
+ /* Colibri I2C */
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ IMX8QXP_MIPI_DSI0_GPIO0_00_ADMA_I2C1_SCL 0x06000021 /* SODIMM 196 */
+ IMX8QXP_MIPI_DSI0_GPIO0_01_ADMA_I2C1_SDA 0x06000021 /* SODIMM 194 */
+ >;
+ };
+
+ /* Colibri Parallel RGB LCD Interface */
+ pinctrl_lcdif: lcdifgrp {
+ fsl,pins = <
+ IMX8QXP_MCLK_OUT0_ADMA_LCDIF_CLK 0x60 /* SODIMM 56 */
+ IMX8QXP_SPI3_CS0_ADMA_LCDIF_HSYNC 0x60 /* SODIMM 68 */
+ IMX8QXP_MCLK_IN0_ADMA_LCDIF_VSYNC 0x60 /* SODIMM 82 */
+ IMX8QXP_MCLK_IN1_ADMA_LCDIF_EN 0x60 /* SODIMM 44 */
+ IMX8QXP_USDHC1_RESET_B_LSIO_GPIO4_IO19 0x60 /* SODIMM 44 */
+ IMX8QXP_ESAI0_FSR_ADMA_LCDIF_D00 0x60 /* SODIMM 76 */
+ IMX8QXP_USDHC1_WP_LSIO_GPIO4_IO21 0x60 /* SODIMM 76 */
+ IMX8QXP_ESAI0_FST_ADMA_LCDIF_D01 0x60 /* SODIMM 70 */
+ IMX8QXP_ESAI0_SCKR_ADMA_LCDIF_D02 0x60 /* SODIMM 60 */
+ IMX8QXP_ESAI0_SCKT_ADMA_LCDIF_D03 0x60 /* SODIMM 58 */
+ IMX8QXP_ESAI0_TX0_ADMA_LCDIF_D04 0x60 /* SODIMM 78 */
+ IMX8QXP_ESAI0_TX1_ADMA_LCDIF_D05 0x60 /* SODIMM 72 */
+ IMX8QXP_ESAI0_TX2_RX3_ADMA_LCDIF_D06 0x60 /* SODIMM 80 */
+ IMX8QXP_ESAI0_TX3_RX2_ADMA_LCDIF_D07 0x60 /* SODIMM 46 */
+ IMX8QXP_ESAI0_TX4_RX1_ADMA_LCDIF_D08 0x60 /* SODIMM 62 */
+ IMX8QXP_ESAI0_TX5_RX0_ADMA_LCDIF_D09 0x60 /* SODIMM 48 */
+ IMX8QXP_SPDIF0_RX_ADMA_LCDIF_D10 0x60 /* SODIMM 74 */
+ IMX8QXP_SPDIF0_TX_ADMA_LCDIF_D11 0x60 /* SODIMM 50 */
+ IMX8QXP_SPDIF0_EXT_CLK_ADMA_LCDIF_D12 0x60 /* SODIMM 52 */
+ IMX8QXP_SPI3_SCK_ADMA_LCDIF_D13 0x60 /* SODIMM 54 */
+ IMX8QXP_SPI3_SDO_ADMA_LCDIF_D14 0x60 /* SODIMM 66 */
+ IMX8QXP_SPI3_SDI_ADMA_LCDIF_D15 0x60 /* SODIMM 64 */
+ IMX8QXP_SPI3_CS1_ADMA_LCDIF_D16 0x60 /* SODIMM 57 */
+ IMX8QXP_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01 0x60 /* SODIMM 57 */
+ IMX8QXP_UART1_CTS_B_ADMA_LCDIF_D17 0x60 /* SODIMM 61 */
+ >;
+ };
+
+ /* Colibri SPI */
+ pinctrl_lpspi2: lpspi2grp {
+ fsl,pins = <
+ IMX8QXP_SPI2_CS0_LSIO_GPIO1_IO00 0x21 /* SODIMM 86 */
+ IMX8QXP_SPI2_SDO_ADMA_SPI2_SDO 0x06000040 /* SODIMM 92 */
+ IMX8QXP_SPI2_SDI_ADMA_SPI2_SDI 0x06000040 /* SODIMM 90 */
+ IMX8QXP_SPI2_SCK_ADMA_SPI2_SCK 0x06000040 /* SODIMM 88 */
+ >;
+ };
+
+ /* Colibri UART_B */
+ pinctrl_lpuart0: lpuart0grp {
+ fsl,pins = <
+ IMX8QXP_UART0_RX_ADMA_UART0_RX 0x06000020 /* SODIMM 36 */
+ IMX8QXP_UART0_TX_ADMA_UART0_TX 0x06000020 /* SODIMM 38 */
+ IMX8QXP_FLEXCAN0_RX_ADMA_UART0_RTS_B 0x06000020 /* SODIMM 34 */
+ IMX8QXP_FLEXCAN0_TX_ADMA_UART0_CTS_B 0x06000020 /* SODIMM 32 */
+ >;
+ };
+
+ /* Colibri UART_C */
+ pinctrl_lpuart2: lpuart2grp {
+ fsl,pins = <
+ IMX8QXP_UART2_RX_ADMA_UART2_RX 0x06000020 /* SODIMM 19 */
+ IMX8QXP_UART2_TX_ADMA_UART2_TX 0x06000020 /* SODIMM 21 */
+ >;
+ };
+
+ /* Colibri UART_A */
+ pinctrl_lpuart3: lpuart3grp {
+ fsl,pins = <
+ IMX8QXP_FLEXCAN2_RX_ADMA_UART3_RX 0x06000020 /* SODIMM 33 */
+ IMX8QXP_FLEXCAN2_TX_ADMA_UART3_TX 0x06000020 /* SODIMM 35 */
+ >;
+ };
+
+ /* Colibri UART_A Control */
+ pinctrl_lpuart3_ctrl: lpuart3ctrlgrp {
+ fsl,pins = <
+ IMX8QXP_MIPI_DSI1_GPIO0_01_LSIO_GPIO2_IO00 0x20 /* SODIMM 23 */
+ IMX8QXP_SAI1_RXD_LSIO_GPIO0_IO29 0x20 /* SODIMM 25 */
+ IMX8QXP_SAI1_RXC_LSIO_GPIO0_IO30 0x20 /* SODIMM 27 */
+ IMX8QXP_CSI_RESET_LSIO_GPIO3_IO03 0x20 /* SODIMM 29 */
+ IMX8QXP_USDHC1_CD_B_LSIO_GPIO4_IO22 0x20 /* SODIMM 31 */
+ IMX8QXP_CSI_EN_LSIO_GPIO3_IO02 0x20 /* SODIMM 37 */
+ >;
+ };
+
+ /* On module wifi module */
+ pinctrl_pcieb: pciebgrp {
+ fsl,pins = <
+ IMX8QXP_PCIE_CTRL0_CLKREQ_B_LSIO_GPIO4_IO01 0x04000061 /* SODIMM 178 */
+ IMX8QXP_PCIE_CTRL0_WAKE_B_LSIO_GPIO4_IO02 0x04000061 /* SODIMM 94 */
+ IMX8QXP_PCIE_CTRL0_PERST_B_LSIO_GPIO4_IO00 0x60 /* SODIMM 81 */
+ >;
+ };
+
+ /* Colibri PWM_A */
+ pinctrl_pwm_a: pwmagrp {
+ /* both pins are connected together, reserve the unused CSI_D05 */
+ fsl,pins = <
+ IMX8QXP_CSI_D05_CI_PI_D07 0x61 /* SODIMM 59 */
+ IMX8QXP_SPI0_CS1_ADMA_LCD_PWM0_OUT 0x60 /* SODIMM 59 */
+ >;
+ };
+
+ /* Colibri PWM_B */
+ pinctrl_pwm_b: pwmbgrp {
+ fsl,pins = <
+ IMX8QXP_UART1_TX_LSIO_PWM0_OUT 0x60 /* SODIMM 28 */
+ >;
+ };
+
+ /* Colibri PWM_C */
+ pinctrl_pwm_c: pwmcgrp {
+ fsl,pins = <
+ IMX8QXP_UART1_RX_LSIO_PWM1_OUT 0x60 /* SODIMM 30 */
+ >;
+ };
+
+ /* Colibri PWM_D */
+ pinctrl_pwm_d: pwmdgrp {
+ /* both pins are connected together, reserve the unused CSI_D04 */
+ fsl,pins = <
+ IMX8QXP_CSI_D04_CI_PI_D06 0x61 /* SODIMM 67 */
+ IMX8QXP_UART1_RTS_B_LSIO_PWM2_OUT 0x60 /* SODIMM 67 */
+ >;
+ };
+
+ /* On-module I2S */
+ pinctrl_sai0: sai0grp {
+ fsl,pins = <
+ IMX8QXP_SPI0_SDI_ADMA_SAI0_TXD 0x06000040
+ IMX8QXP_SPI0_CS0_ADMA_SAI0_RXD 0x06000040
+ IMX8QXP_SPI0_SCK_ADMA_SAI0_TXC 0x06000040
+ IMX8QXP_SPI0_SDO_ADMA_SAI0_TXFS 0x06000040
+ >;
+ };
+
+ /* Colibri Audio Analogue Microphone GND */
+ pinctrl_sgtl5000: sgtl5000grp {
+ fsl,pins = <
+ /* MIC GND EN */
+ IMX8QXP_MIPI_CSI0_I2C0_SDA_LSIO_GPIO3_IO06 0x41
+ >;
+ };
+
+ /* On-module SGTL5000 clock */
+ pinctrl_sgtl5000_usb_clk: sgtl5000usbclkgrp {
+ fsl,pins = <
+ IMX8QXP_ADC_IN3_ADMA_ACM_MCLK_OUT0 0x21
+ >;
+ };
+
+ /* On-module USB interrupt */
+ pinctrl_usb3503a: usb3503agrp {
+ fsl,pins = <
+ IMX8QXP_MIPI_CSI0_MCLK_OUT_LSIO_GPIO3_IO04 0x61
+ >;
+ };
+
+ /* Colibri USB Client Cable Detect */
+ pinctrl_usbc_det: usbcdetgrp {
+ fsl,pins = <
+ IMX8QXP_ENET0_REFCLK_125M_25M_LSIO_GPIO5_IO09 0x06000040 /* SODIMM 137 */
+ >;
+ };
+
+ /* USB Host Power Enable */
+ pinctrl_usbh1_reg: usbh1reggrp {
+ fsl,pins = <
+ IMX8QXP_USB_SS3_TC0_LSIO_GPIO4_IO03 0x06000040 /* SODIMM 129 */
+ >;
+ };
+
+ /* On-module eMMC */
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
+ IMX8QXP_EMMC0_CMD_CONN_EMMC0_CMD 0x21
+ IMX8QXP_EMMC0_DATA0_CONN_EMMC0_DATA0 0x21
+ IMX8QXP_EMMC0_DATA1_CONN_EMMC0_DATA1 0x21
+ IMX8QXP_EMMC0_DATA2_CONN_EMMC0_DATA2 0x21
+ IMX8QXP_EMMC0_DATA3_CONN_EMMC0_DATA3 0x21
+ IMX8QXP_EMMC0_DATA4_CONN_EMMC0_DATA4 0x21
+ IMX8QXP_EMMC0_DATA5_CONN_EMMC0_DATA5 0x21
+ IMX8QXP_EMMC0_DATA6_CONN_EMMC0_DATA6 0x21
+ IMX8QXP_EMMC0_DATA7_CONN_EMMC0_DATA7 0x21
+ IMX8QXP_EMMC0_STROBE_CONN_EMMC0_STROBE 0x41
+ IMX8QXP_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x21
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
+ IMX8QXP_EMMC0_CMD_CONN_EMMC0_CMD 0x21
+ IMX8QXP_EMMC0_DATA0_CONN_EMMC0_DATA0 0x21
+ IMX8QXP_EMMC0_DATA1_CONN_EMMC0_DATA1 0x21
+ IMX8QXP_EMMC0_DATA2_CONN_EMMC0_DATA2 0x21
+ IMX8QXP_EMMC0_DATA3_CONN_EMMC0_DATA3 0x21
+ IMX8QXP_EMMC0_DATA4_CONN_EMMC0_DATA4 0x21
+ IMX8QXP_EMMC0_DATA5_CONN_EMMC0_DATA5 0x21
+ IMX8QXP_EMMC0_DATA6_CONN_EMMC0_DATA6 0x21
+ IMX8QXP_EMMC0_DATA7_CONN_EMMC0_DATA7 0x21
+ IMX8QXP_EMMC0_STROBE_CONN_EMMC0_STROBE 0x41
+ IMX8QXP_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x21
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
+ IMX8QXP_EMMC0_CMD_CONN_EMMC0_CMD 0x21
+ IMX8QXP_EMMC0_DATA0_CONN_EMMC0_DATA0 0x21
+ IMX8QXP_EMMC0_DATA1_CONN_EMMC0_DATA1 0x21
+ IMX8QXP_EMMC0_DATA2_CONN_EMMC0_DATA2 0x21
+ IMX8QXP_EMMC0_DATA3_CONN_EMMC0_DATA3 0x21
+ IMX8QXP_EMMC0_DATA4_CONN_EMMC0_DATA4 0x21
+ IMX8QXP_EMMC0_DATA5_CONN_EMMC0_DATA5 0x21
+ IMX8QXP_EMMC0_DATA6_CONN_EMMC0_DATA6 0x21
+ IMX8QXP_EMMC0_DATA7_CONN_EMMC0_DATA7 0x21
+ IMX8QXP_EMMC0_STROBE_CONN_EMMC0_STROBE 0x41
+ IMX8QXP_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x21
+ >;
+ };
+
+ /* Colibri SD/MMC Card Detect */
+ pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+ fsl,pins = <
+ IMX8QXP_QSPI0A_DATA0_LSIO_GPIO3_IO09 0x06000021 /* SODIMM 43 */
+ >;
+ };
+
+ pinctrl_usdhc2_gpio_sleep: usdhc2gpioslpgrp {
+ fsl,pins = <
+ IMX8QXP_QSPI0A_DATA0_LSIO_GPIO3_IO09 0x60 /* SODIMM 43 */
+ >;
+ };
+
+ /* Colibri SD/MMC Card */
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ IMX8QXP_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041 /* SODIMM 47 */
+ IMX8QXP_USDHC1_CMD_CONN_USDHC1_CMD 0x21 /* SODIMM 190 */
+ IMX8QXP_USDHC1_DATA0_CONN_USDHC1_DATA0 0x21 /* SODIMM 192 */
+ IMX8QXP_USDHC1_DATA1_CONN_USDHC1_DATA1 0x21 /* SODIMM 49 */
+ IMX8QXP_USDHC1_DATA2_CONN_USDHC1_DATA2 0x21 /* SODIMM 51 */
+ IMX8QXP_USDHC1_DATA3_CONN_USDHC1_DATA3 0x21 /* SODIMM 53 */
+ IMX8QXP_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x21
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ IMX8QXP_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041 /* SODIMM 47 */
+ IMX8QXP_USDHC1_CMD_CONN_USDHC1_CMD 0x21 /* SODIMM 190 */
+ IMX8QXP_USDHC1_DATA0_CONN_USDHC1_DATA0 0x21 /* SODIMM 192 */
+ IMX8QXP_USDHC1_DATA1_CONN_USDHC1_DATA1 0x21 /* SODIMM 49 */
+ IMX8QXP_USDHC1_DATA2_CONN_USDHC1_DATA2 0x21 /* SODIMM 51 */
+ IMX8QXP_USDHC1_DATA3_CONN_USDHC1_DATA3 0x21 /* SODIMM 53 */
+ IMX8QXP_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x21
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ IMX8QXP_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041 /* SODIMM 47 */
+ IMX8QXP_USDHC1_CMD_CONN_USDHC1_CMD 0x21 /* SODIMM 190 */
+ IMX8QXP_USDHC1_DATA0_CONN_USDHC1_DATA0 0x21 /* SODIMM 192 */
+ IMX8QXP_USDHC1_DATA1_CONN_USDHC1_DATA1 0x21 /* SODIMM 49 */
+ IMX8QXP_USDHC1_DATA2_CONN_USDHC1_DATA2 0x21 /* SODIMM 51 */
+ IMX8QXP_USDHC1_DATA3_CONN_USDHC1_DATA3 0x21 /* SODIMM 53 */
+ IMX8QXP_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x21
+ >;
+ };
+
+ pinctrl_usdhc2_sleep: usdhc2slpgrp {
+ fsl,pins = <
+ IMX8QXP_USDHC1_CLK_LSIO_GPIO4_IO23 0x60 /* SODIMM 47 */
+ IMX8QXP_USDHC1_CMD_LSIO_GPIO4_IO24 0x60 /* SODIMM 190 */
+ IMX8QXP_USDHC1_DATA0_LSIO_GPIO4_IO25 0x60 /* SODIMM 192 */
+ IMX8QXP_USDHC1_DATA1_LSIO_GPIO4_IO26 0x60 /* SODIMM 49 */
+ IMX8QXP_USDHC1_DATA2_LSIO_GPIO4_IO27 0x60 /* SODIMM 51 */
+ IMX8QXP_USDHC1_DATA3_LSIO_GPIO4_IO28 0x60 /* SODIMM 53 */
+ IMX8QXP_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x21
+ >;
+ };
+
+ pinctrl_wifi: wifigrp {
+ fsl,pins = <
+ IMX8QXP_SCU_BOOT_MODE3_SCU_DSC_RTC_CLOCK_OUTPUT_32K 0x20
+ >;
+ };
+};
--
2.21.0
From: Marcel Ziswiler <[email protected]>
Document the NXP SoC based Toradex Colibri iMX8X module and carrier
board devicetree bindings previously added.
Signed-off-by: Marcel Ziswiler <[email protected]>
---
Changes in v2:
- Document board compatibles in a separate patch as suggested by Shawn.
Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 96b05484527e..c835a6fba1bf 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -277,6 +277,8 @@ properties:
- enum:
- einfochips,imx8qxp-ai_ml # i.MX8QXP AI_ML Board
- fsl,imx8qxp-mek # i.MX8QXP MEK Board
+ - toradex,colibri-imx8x # Colibri iMX8X Module
+ - toradex,colibri-imx8x-eval-v3 # Colibri iMX8X Module on Colibri Evaluation Board V3
- const: fsl,imx8qxp
- description:
--
2.21.0
On Sat, 26 Oct 2019 11:04:03 +0200, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <[email protected]>
>
> Document the NXP SoC based Toradex Colibri iMX8X module and carrier
> board devicetree bindings previously added.
>
> Signed-off-by: Marcel Ziswiler <[email protected]>
>
> ---
>
> Changes in v2:
> - Document board compatibles in a separate patch as suggested by Shawn.
>
> Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Reviewed-by: Rob Herring <[email protected]>
On Sat, Oct 26, 2019 at 11:03:59AM +0200, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <[email protected]>
>
> Fix typo in top-level module compatible.
>
> Signed-off-by: Marcel Ziswiler <[email protected]>
>
> ---
>
> Changes in v2: New patch.
>
> arch/arm/boot/dts/vf500-colibri.dtsi | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/vf500-colibri.dtsi b/arch/arm/boot/dts/vf500-colibri.dtsi
> index 237b0246fa84..92255f8893ce 100644
> --- a/arch/arm/boot/dts/vf500-colibri.dtsi
> +++ b/arch/arm/boot/dts/vf500-colibri.dtsi
> @@ -44,7 +44,7 @@
>
> / {
> model = "Toradex Colibri VF50 COM";
> - compatible = "toradex,vf610-colibri_vf50", "fsl,vf500";
> + compatible = "toradex,vf500-colibri_vf50", "fsl,vf500";
Do we need to update bindings doc for this?
Also as a practise, we use 'ARM: ...' for arch/arm/ patches going through
IMX tree.
Shawn
>
> memory@80000000 {
> device_type = "memory";
> --
> 2.21.0
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Mon, Nov 04, 2019 at 09:16:58AM +0800, Shawn Guo wrote:
> On Sat, Oct 26, 2019 at 11:03:59AM +0200, Marcel Ziswiler wrote:
> > From: Marcel Ziswiler <[email protected]>
> >
> > Fix typo in top-level module compatible.
> >
> > Signed-off-by: Marcel Ziswiler <[email protected]>
> >
> > ---
> >
> > Changes in v2: New patch.
> >
> > arch/arm/boot/dts/vf500-colibri.dtsi | 2 +-
> > 1 file changed, 1 insertion(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/boot/dts/vf500-colibri.dtsi b/arch/arm/boot/dts/vf500-colibri.dtsi
> > index 237b0246fa84..92255f8893ce 100644
> > --- a/arch/arm/boot/dts/vf500-colibri.dtsi
> > +++ b/arch/arm/boot/dts/vf500-colibri.dtsi
> > @@ -44,7 +44,7 @@
> >
> > / {
> > model = "Toradex Colibri VF50 COM";
> > - compatible = "toradex,vf610-colibri_vf50", "fsl,vf500";
> > + compatible = "toradex,vf500-colibri_vf50", "fsl,vf500";
>
> Do we need to update bindings doc for this?
Sorry. I should have read the whole series.
>
> Also as a practise, we use 'ARM: ...' for arch/arm/ patches going through
> IMX tree.
I fixed it up and applied the series.
Shawn
On Mon, Nov 04, 2019 at 09:20:35AM +0800, Shawn Guo wrote:
> > Also as a practise, we use 'ARM: ...' for arch/arm/ patches going through
> > IMX tree.
>
> I fixed it up and applied the series.
Just let you know that I did not receive patch #3.
Shawn
On Sat, Oct 26, 2019 at 11:04:03AM +0200, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <[email protected]>
>
> Document the NXP SoC based Toradex Colibri iMX8X module and carrier
> board devicetree bindings previously added.
>
> Signed-off-by: Marcel Ziswiler <[email protected]>
I changed subject a little bit as below.
dt-bindings: arm: fsl: add nxp based toradex colibri-imx8x bindings
Shawn
Hi Shawn
On November 4, 2019 2:29:58 AM GMT+01:00, Shawn Guo <[email protected]> wrote:
>On Mon, Nov 04, 2019 at 09:20:35AM +0800, Shawn Guo wrote:
>> > Also as a practise, we use 'ARM: ...' for arch/arm/ patches going
>through
>> > IMX tree.
>>
>> I fixed it up and applied the series.
>
>Just let you know that I did not receive patch #3.
I believe #3 got already applied by input subsystem maintainer Dmitry Torokhov. However, so far I believe he hasn't pushed that one as of yet.
>Shawn
Thanks, Shawn!
Cheers
Marcel