Apply Errata i913 every time the functional clock is enabled.
This should take care of suspend/resume case as well.
Signed-off-by: Benoit Parrot <[email protected]>
Signed-off-by: Jyri Sarha <[email protected]>
---
drivers/media/platform/ti-vpe/cal.c | 57 +++++++++++++++++++++++-
drivers/media/platform/ti-vpe/cal_regs.h | 27 +++++++++++
2 files changed, 82 insertions(+), 2 deletions(-)
diff --git a/drivers/media/platform/ti-vpe/cal.c b/drivers/media/platform/ti-vpe/cal.c
index eb3727ba185d..3b04aff6c778 100644
--- a/drivers/media/platform/ti-vpe/cal.c
+++ b/drivers/media/platform/ti-vpe/cal.c
@@ -282,6 +282,12 @@ static const struct cal_data dra72x_cal_data = {
.num_csi2_phy = ARRAY_SIZE(dra72x_cal_csi_phy),
};
+static const struct cal_data dra72x_es1_cal_data = {
+ .csi2_phy_core = dra72x_cal_csi_phy,
+ .num_csi2_phy = ARRAY_SIZE(dra72x_cal_csi_phy),
+ .flags = DRA72_CAL_PRE_ES2_LDO_DISABLE,
+};
+
/*
* there is one cal_dev structure in the driver, it is shared by
* all instances.
@@ -567,9 +573,52 @@ static void cal_get_hwinfo(struct cal_dev *dev)
hwinfo);
}
-static inline int cal_runtime_get(struct cal_dev *dev)
+/*
+ * Errata i913: CSI2 LDO Needs to be disabled when module is powered on
+ *
+ * Enabling CSI2 LDO shorts it to core supply. It is crucial the 2 CSI2
+ * LDOs on the device are disabled if CSI-2 module is powered on
+ * (0x4845 B304 | 0x4845 B384 [28:27] = 0x1) or in ULPS (0x4845 B304
+ * | 0x4845 B384 [28:27] = 0x2) mode. Common concerns include: high
+ * current draw on the module supply in active mode.
+ *
+ * Errata does not apply when CSI-2 module is powered off
+ * (0x4845 B304 | 0x4845 B384 [28:27] = 0x0).
+ *
+ * SW Workaround:
+ * Set the following register bits to disable the LDO,
+ * which is essentially CSI2 REG10 bit 6:
+ *
+ * Core 0: 0x4845 B828 = 0x0000 0040
+ * Core 1: 0x4845 B928 = 0x0000 0040
+ */
+static void i913_errata(struct cal_dev *dev, unsigned int port)
{
- return pm_runtime_get_sync(&dev->pdev->dev);
+ u32 reg10 = reg_read(dev->cc[port], CAL_CSI2_PHY_REG10);
+
+ set_field(®10, CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_DISABLE,
+ CAL_CSI2_PHY_REG10_I933_LDO_DISABLE_MASK);
+
+ cal_dbg(1, dev, "CSI2_%d_REG10 = 0x%08x\n", port, reg10);
+ reg_write(dev->cc[port], CAL_CSI2_PHY_REG10, reg10);
+}
+
+static int cal_runtime_get(struct cal_dev *dev)
+{
+ int r;
+
+ r = pm_runtime_get_sync(&dev->pdev->dev);
+
+ if (dev->flags & DRA72_CAL_PRE_ES2_LDO_DISABLE) {
+ /*
+ * Apply errata on both port eveytime we (re-)enable
+ * the clock
+ */
+ i913_errata(dev, 0);
+ i913_errata(dev, 1);
+ }
+
+ return r;
}
static inline void cal_runtime_put(struct cal_dev *dev)
@@ -2064,6 +2113,10 @@ static const struct of_device_id cal_of_match[] = {
.compatible = "ti,dra72-cal",
.data = (void *)&dra72x_cal_data,
},
+ {
+ .compatible = "ti,dra72-pre-es2-cal",
+ .data = (void *)&dra72x_es1_cal_data,
+ },
{},
};
MODULE_DEVICE_TABLE(of, cal_of_match);
diff --git a/drivers/media/platform/ti-vpe/cal_regs.h b/drivers/media/platform/ti-vpe/cal_regs.h
index 9e6afd0770c8..a40e77f3e977 100644
--- a/drivers/media/platform/ti-vpe/cal_regs.h
+++ b/drivers/media/platform/ti-vpe/cal_regs.h
@@ -10,6 +10,30 @@
#ifndef __TI_CAL_REGS_H
#define __TI_CAL_REGS_H
+/*
+ * struct cal_dev.flags possibilities
+ *
+ * DRA72_CAL_PRE_ES2_LDO_DISABLE:
+ * Errata i913: CSI2 LDO Needs to be disabled when module is powered on
+ *
+ * Enabling CSI2 LDO shorts it to core supply. It is crucial the 2 CSI2
+ * LDOs on the device are disabled if CSI-2 module is powered on
+ * (0x4845 B304 | 0x4845 B384 [28:27] = 0x1) or in ULPS (0x4845 B304
+ * | 0x4845 B384 [28:27] = 0x2) mode. Common concerns include: high
+ * current draw on the module supply in active mode.
+ *
+ * Errata does not apply when CSI-2 module is powered off
+ * (0x4845 B304 | 0x4845 B384 [28:27] = 0x0).
+ *
+ * SW Workaround:
+ * Set the following register bits to disable the LDO,
+ * which is essentially CSI2 REG10 bit 6:
+ *
+ * Core 0: 0x4845 B828 = 0x0000 0040
+ * Core 1: 0x4845 B928 = 0x0000 0040
+ */
+#define DRA72_CAL_PRE_ES2_LDO_DISABLE BIT(0)
+
#define CAL_NUM_CSI2_PORTS 2
/* CAL register offsets */
@@ -71,6 +95,7 @@
#define CAL_CSI2_PHY_REG0 0x000
#define CAL_CSI2_PHY_REG1 0x004
#define CAL_CSI2_PHY_REG2 0x008
+#define CAL_CSI2_PHY_REG10 0x028
/* CAL Control Module Core Camerrx Control register offsets */
#define CM_CTRL_CORE_CAMERRX_CONTROL 0x000
@@ -458,6 +483,8 @@
#define CAL_CSI2_PHY_REG1_CLOCK_MISS_DETECTOR_STATUS_SUCCESS 0
#define CAL_CSI2_PHY_REG1_RESET_DONE_STATUS_MASK GENMASK(29, 28)
+#define CAL_CSI2_PHY_REG10_I933_LDO_DISABLE_MASK BIT(6)
+
#define CAL_CSI2_PHY_REG2_CCP2_SYNC_PATTERN_MASK GENMASK(23, 0)
#define CAL_CSI2_PHY_REG2_TRIGGER_CMD_RXTRIGESC3_MASK GENMASK(25, 24)
#define CAL_CSI2_PHY_REG2_TRIGGER_CMD_RXTRIGESC2_MASK GENMASK(27, 26)
--
2.17.1