The first patch converts the ADC DT bindings from .txt to .yaml format.
The second patch updates the documentation, for PMIC7 ADC. The main
difference between PMIC5 and PMIC7 for ADC is that for PMIC7, SW requests to
ADCs (on any PMIC) need to go through the ADC on PMK8350, which communicates with
the ADCs on other PMICs through PBS. A SID register has been added for SW to specify
the PMIC with which it needs to communicate.
The third patch adds driver support for PMIC7 ADC. It also adds definitions for
PMIC7 ADC channels and virtual channel definitions per PMIC (made by combining ADC
channel number and PMIC SID), to be used by ADC clients for PMIC7.
Jishnu Prakash (3):
iio: adc: Convert the QCOM SPMI ADC bindings to .yaml format
iio: adc: Add PMIC7 ADC bindings
iio: adc: Add support for PMIC7 ADC
.../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 173 --------------
.../bindings/iio/adc/qcom,spmi-vadc.yaml | 192 +++++++++++++++
drivers/iio/adc/qcom-spmi-adc5.c | 239 ++++++++++++++++++-
drivers/iio/adc/qcom-vadc-common.c | 260 +++++++++++++++++++++
drivers/iio/adc/qcom-vadc-common.h | 14 ++
include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h | 67 ++++++
include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h | 88 +++++++
include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h | 46 ++++
include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h | 28 +++
include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h | 28 +++
include/dt-bindings/iio/qcom,spmi-vadc.h | 78 ++++++-
11 files changed, 1035 insertions(+), 178 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Convert the adc bindings from .txt to .yaml format.
Signed-off-by: Jishnu Prakash <[email protected]>
---
.../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 173 --------------------
.../bindings/iio/adc/qcom,spmi-vadc.yaml | 178 +++++++++++++++++++++
2 files changed, 178 insertions(+), 173 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
deleted file mode 100644
index c878768..0000000
--- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
+++ /dev/null
@@ -1,173 +0,0 @@
-Qualcomm's SPMI PMIC ADC
-
-- SPMI PMIC voltage ADC (VADC) provides interface to clients to read
- voltage. The VADC is a 15-bit sigma-delta ADC.
-- SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
- voltage. The VADC is a 16-bit sigma-delta ADC.
-
-VADC node:
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: Should contain "qcom,spmi-vadc".
- Should contain "qcom,spmi-adc5" for PMIC5 ADC driver.
- Should contain "qcom,spmi-adc-rev2" for PMIC rev2 ADC driver.
- Should contain "qcom,pms405-adc" for PMS405 PMIC
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: VADC base address in the SPMI PMIC register map.
-
-- #address-cells:
- Usage: required
- Value type: <u32>
- Definition: Must be one. Child node 'reg' property should define ADC
- channel number.
-
-- #size-cells:
- Usage: required
- Value type: <u32>
- Definition: Must be zero.
-
-- #io-channel-cells:
- Usage: required
- Value type: <u32>
- Definition: Must be one. For details about IIO bindings see:
- Documentation/devicetree/bindings/iio/iio-bindings.txt
-
-- interrupts:
- Usage: optional
- Value type: <prop-encoded-array>
- Definition: End of conversion interrupt.
-
-Channel node properties:
-
-- reg:
- Usage: required
- Value type: <u32>
- Definition: ADC channel number.
- See include/dt-bindings/iio/qcom,spmi-vadc.h
-
-- label:
- Usage: required for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2"
- Value type: <empty>
- Definition: ADC input of the platform as seen in the schematics.
- For thermistor inputs connected to generic AMUX or GPIO inputs
- these can vary across platform for the same pins. Hence select
- the platform schematics name for this channel.
-
-- qcom,decimation:
- Usage: optional
- Value type: <u32>
- Definition: This parameter is used to decrease ADC sampling rate.
- Quicker measurements can be made by reducing decimation ratio.
- - For compatible property "qcom,spmi-vadc", valid values are
- 512, 1024, 2048, 4096. If property is not found, default value
- of 512 will be used.
- - For compatible property "qcom,spmi-adc5", valid values are 250, 420
- and 840. If property is not found, default value of 840 is used.
- - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
- 512 and 1024. If property is not present, default value is 1024.
-
-- qcom,pre-scaling:
- Usage: optional
- Value type: <u32 array>
- Definition: Used for scaling the channel input signal before the signal is
- fed to VADC. The configuration for this node is to know the
- pre-determined ratio and use it for post scaling. Select one from
- the following options.
- <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
- If property is not found default value depending on chip will be used.
-
-- qcom,ratiometric:
- Usage: optional
- Value type: <empty>
- Definition: Channel calibration type.
- - For compatible property "qcom,spmi-vadc", if this property is
- specified VADC will use the VDD reference (1.8V) and GND for
- channel calibration. If property is not found, channel will be
- calibrated with 0.625V and 1.25V reference channels, also
- known as absolute calibration.
- - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
- if this property is specified VADC will use the VDD reference
- (1.875V) and GND for channel calibration. If property is not found,
- channel will be calibrated with 0V and 1.25V reference channels,
- also known as absolute calibration.
-
-- qcom,hw-settle-time:
- Usage: optional
- Value type: <u32>
- Definition: Time between AMUX getting configured and the ADC starting
- conversion. The 'hw_settle_time' is an index used from valid values
- and programmed in hardware to achieve the hardware settling delay.
- - For compatible property "qcom,spmi-vadc" and "qcom,spmi-adc-rev2",
- Delay = 100us * (hw_settle_time) for hw_settle_time < 11,
- and 2ms * (hw_settle_time - 10) otherwise.
- Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800,
- 900 us and 1, 2, 4, 6, 8, 10 ms.
- If property is not found, channel will use 0us.
- - For compatible property "qcom,spmi-adc5", delay = 15us for
- value 0, 100us * (value) for values < 11,
- and 2ms * (value - 10) otherwise.
- Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 800,
- 900 us and 1, 2, 4, 6, 8, 10 ms
- Certain controller digital versions have valid values of
- 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms
- If property is not found, channel will use 15us.
-
-- qcom,avg-samples:
- Usage: optional
- Value type: <u32>
- Definition: Number of samples to be used for measurement.
- Averaging provides the option to obtain a single measurement
- from the ADC that is an average of multiple samples. The value
- selected is 2^(value).
- - For compatible property "qcom,spmi-vadc", valid values
- are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
- If property is not found, 1 sample will be used.
- - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
- valid values are: 1, 2, 4, 8, 16
- If property is not found, 1 sample will be used.
-
-NOTE:
-
-For compatible property "qcom,spmi-vadc" following channels, also known as
-reference point channels, are used for result calibration and their channel
-configuration nodes should be defined:
-VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV,
-VADC_GND_REF and VADC_VDD_VADC.
-
-Example:
-
-#include <dt-bindings/iio/qcom,spmi-vadc.h>
-#include <linux/irq.h>
-/* ... */
-
- /* VADC node */
- pmic_vadc: vadc@3100 {
- compatible = "qcom,spmi-vadc";
- reg = <0x3100>;
- interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
- #address-cells = <1>;
- #size-cells = <0>;
- #io-channel-cells = <1>;
- io-channel-ranges;
-
- /* Channel node */
- adc-chan@VADC_LR_MUX10_USB_ID {
- reg = <VADC_LR_MUX10_USB_ID>;
- qcom,decimation = <512>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,avg-samples = <1>;
- qcom,pre-scaling = <1 3>;
- };
- };
-
- /* IIO client node */
- usb {
- io-channels = <&pmic_vadc VADC_LR_MUX10_USB_ID>;
- io-channel-names = "vadc";
- };
diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
new file mode 100644
index 0000000..72db14c
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
@@ -0,0 +1,178 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/qcom,spmi-vadc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm's SPMI PMIC ADC
+
+maintainers:
+ - Andy Gross <[email protected]>
+ - Bjorn Andersson <[email protected]>
+
+description: |
+ SPMI PMIC voltage ADC (VADC) provides interface to clients to read
+ voltage. The VADC is a 15-bit sigma-delta ADC.
+ SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
+ voltage. The VADC is a 16-bit sigma-delta ADC.
+
+properties:
+ compatible:
+ enum:
+ - qcom,spmi-vadc
+ - qcom,spmi-adc5
+ - qcom,spmi-adc-rev2
+ - qcom,pms405-adc
+
+ reg:
+ description: VADC base address in the SPMI PMIC register map
+ maxItems: 1
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ '#io-channel-cells':
+ const: 1
+
+ interrupts:
+ maxItems: 1
+ description:
+ End of conversion interrupt.
+
+required:
+ - compatible
+ - reg
+ - '#address-cells'
+ - '#size-cells'
+ - '#io-channel-cells'
+
+patternProperties:
+ "^[a-z0-9-_@]$":
+ type: object
+ description: |
+ Represents the external channels which are connected to the ADC.
+ For compatible property "qcom,spmi-vadc" following channels, also known as
+ reference point channels, are used for result calibration and their channel
+ configuration nodes should be defined:
+ VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV,
+ VADC_GND_REF and VADC_VDD_VADC.
+
+ properties:
+ reg:
+ description: |
+ ADC channel number.
+ See include/dt-bindings/iio/qcom,spmi-vadc.h
+
+ label:
+ description: |
+ ADC input of the platform as seen in the schematics.
+ For thermistor inputs connected to generic AMUX or GPIO inputs
+ these can vary across platform for the same pins. Hence select
+ the platform schematics name for this channel. It is required
+ for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2".
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/string
+
+ qcom,decimation:
+ description: |
+ This parameter is used to decrease ADC sampling rate.
+ Quicker measurements can be made by reducing decimation ratio.
+ - For compatible property "qcom,spmi-vadc", valid values are
+ 512, 1024, 2048, 4096. If property is not found, default value
+ of 512 will be used.
+ - For compatible property "qcom,spmi-adc5", valid values are 250, 420
+ and 840. If property is not found, default value of 840 is used.
+ - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
+ 512 and 1024. If property is not present, default value is 1024.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+
+ qcom,pre-scaling:
+ description: |
+ Used for scaling the channel input signal before the signal is
+ fed to VADC. The configuration for this node is to know the
+ pre-determined ratio and use it for post scaling. Select one from
+ the following options.
+ <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
+ If property is not found default value depending on chip will be used.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+
+ qcom,ratiometric:
+ description: |
+ Channel calibration type.
+ - For compatible property "qcom,spmi-vadc", if this property is
+ specified VADC will use the VDD reference (1.8V) and GND for
+ channel calibration. If property is not found, channel will be
+ calibrated with 0.625V and 1.25V reference channels, also
+ known as absolute calibration.
+ - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
+ if this property is specified VADC will use the VDD reference (1.875V)
+ and GND for channel calibration. If property is not found, channel
+ will be calibrated with 0V and 1.25V reference channels, also known
+ as absolute calibration.
+ type: boolean
+
+ qcom,hw-settle-time:
+ description: |
+ Time between AMUX getting configured and the ADC starting
+ conversion. The 'hw_settle_time' is an index used from valid values
+ and programmed in hardware to achieve the hardware settling delay.
+ - For compatible property "qcom,spmi-vadc" and "qcom,spmi-adc-rev2",
+ Delay = 100us * (hw_settle_time) for hw_settle_time < 11,
+ and 2ms * (hw_settle_time - 10) otherwise.
+ Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800,
+ 900 us and 1, 2, 4, 6, 8, 10 ms.
+ If property is not found, channel will use 0us.
+ - For compatible property "qcom,spmi-adc5", delay = 15us for
+ value 0, 100us * (value) for values < 11,
+ and 2ms * (value - 10) otherwise.
+ Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 800,
+ 900 us and 1, 2, 4, 6, 8, 10 ms
+ Certain controller digital versions have valid values of
+ 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms
+ If property is not found, channel will use 15us.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+
+ qcom,avg-samples:
+ description: |
+ Number of samples to be used for measurement.
+ Averaging provides the option to obtain a single measurement
+ from the ADC that is an average of multiple samples. The value
+ selected is 2^(value).
+ - For compatible property "qcom,spmi-vadc", valid values
+ are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
+ If property is not found, 1 sample will be used.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+
+ required:
+ - reg
+ - diff-channels
+
+examples:
+ - |
+ /* VADC node */
+ pmic_vadc: vadc@3100 {
+ compatible = "qcom,spmi-vadc";
+ reg = <0x3100>;
+ interrupts = <0x0 0x31 0x0 0x1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+
+ /* Channel node */
+ adc-chan@0x39 {
+ reg = <0x39>;
+ qcom,decimation = <512>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,avg-samples = <1>;
+ qcom,pre-scaling = <1 3>;
+ };
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
The ADC architecture on PMIC7 is changed as compared to PMIC5. The
major change from PMIC5 is that all SW communication to ADC goes through
PMK8350, which communicates with other PMICs through PBS when the ADC
on PMK8350 works in master mode. The SID register is used to identify the
PMICs with which the PBS needs to communicate. Add support for the same.
In addition, add definitions for ADC channels and virtual channel
definitions per PMIC, to be used by ADC clients for PMIC7.
Signed-off-by: Jishnu Prakash <[email protected]>
---
drivers/iio/adc/qcom-spmi-adc5.c | 239 ++++++++++++++++++++-
drivers/iio/adc/qcom-vadc-common.c | 260 +++++++++++++++++++++++
drivers/iio/adc/qcom-vadc-common.h | 14 ++
include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h | 67 ++++++
include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h | 88 ++++++++
include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h | 46 ++++
include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h | 28 +++
include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h | 28 +++
include/dt-bindings/iio/qcom,spmi-vadc.h | 78 ++++++-
9 files changed, 843 insertions(+), 5 deletions(-)
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h
create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h
diff --git a/drivers/iio/adc/qcom-spmi-adc5.c b/drivers/iio/adc/qcom-spmi-adc5.c
index 21fdcde..bcfb749 100644
--- a/drivers/iio/adc/qcom-spmi-adc5.c
+++ b/drivers/iio/adc/qcom-spmi-adc5.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, 2020, The Linux Foundation. All rights reserved.
*/
#include <linux/bitops.h>
@@ -23,6 +23,7 @@
#define ADC5_USR_REVISION1 0x0
#define ADC5_USR_STATUS1 0x8
+#define ADC5_USR_STATUS1_CONV_FAULT BIT(7)
#define ADC5_USR_STATUS1_REQ_STS BIT(1)
#define ADC5_USR_STATUS1_EOC BIT(0)
#define ADC5_USR_STATUS1_REQ_STS_EOC_MASK 0x3
@@ -65,6 +66,9 @@
#define ADC5_USR_IBAT_DATA1 0x53
+#define ADC_CHANNEL_OFFSET 0x8
+#define ADC_CHANNEL_MASK 0xff
+
/*
* Conversion time varies based on the decimation, clock rate, fast average
* samples and measurements queued across different VADC peripherals.
@@ -79,6 +83,11 @@
#define ADC5_HW_SETTLE_DIFF_MINOR 3
#define ADC5_HW_SETTLE_DIFF_MAJOR 5
+/* For PMIC7 */
+#define ADC_APP_SID 0x40
+#define ADC_APP_SID_MASK 0xf
+#define ADC7_CONV_TIMEOUT msecs_to_jiffies(10)
+
enum adc5_cal_method {
ADC5_NO_CAL = 0,
ADC5_RATIOMETRIC_CAL,
@@ -96,6 +105,7 @@ enum adc5_cal_val {
* @cal_method: calibration method.
* @cal_val: calibration value
* @decimation: sampling rate supported for the channel.
+ * @sid: slave id of PMIC owning the channel, for PMIC7.
* @prescale: channel scaling performed on the input signal.
* @hw_settle_time: the time between AMUX being configured and the
* start of conversion.
@@ -110,6 +120,7 @@ struct adc5_channel_prop {
enum adc5_cal_method cal_method;
enum adc5_cal_val cal_val;
unsigned int decimation;
+ unsigned int sid;
unsigned int prescale;
unsigned int hw_settle_time;
unsigned int avg_samples;
@@ -140,6 +151,7 @@ struct adc5_chip {
bool poll_eoc;
struct completion complete;
struct mutex lock;
+ bool is_pmic7;
const struct adc5_data *data;
};
@@ -165,6 +177,11 @@ static int adc5_write(struct adc5_chip *adc, u16 offset, u8 *data, int len)
return regmap_bulk_write(adc->regmap, adc->base + offset, data, len);
}
+static int adc5_masked_write(struct adc5_chip *adc, u16 offset, u8 mask, u8 val)
+{
+ return regmap_update_bits(adc->regmap, adc->base + offset, mask, val);
+}
+
static int adc5_prescaling_from_dt(u32 num, u32 den)
{
unsigned int pre;
@@ -314,6 +331,49 @@ static int adc5_configure(struct adc5_chip *adc,
return adc5_write(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
}
+static int adc7_configure(struct adc5_chip *adc,
+ struct adc5_channel_prop *prop)
+{
+ int ret;
+ u8 conv_req = 0, buf[4];
+
+ ret = adc5_masked_write(adc, ADC_APP_SID, ADC_APP_SID_MASK, prop->sid);
+ if (ret)
+ return ret;
+
+ ret = adc5_read(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
+ if (ret < 0)
+ return ret;
+
+ /* Digital param selection */
+ adc5_update_dig_param(adc, prop, &buf[0]);
+
+ /* Update fast average sample value */
+ buf[1] &= (u8) ~ADC5_USR_FAST_AVG_CTL_SAMPLES_MASK;
+ buf[1] |= prop->avg_samples;
+
+ /* Select ADC channel */
+ buf[2] = prop->channel;
+
+ /* Select HW settle delay for channel */
+ buf[3] &= (u8) ~ADC5_USR_HW_SETTLE_DELAY_MASK;
+ buf[3] |= prop->hw_settle_time;
+
+ /* Select CONV request */
+ conv_req = ADC5_USR_CONV_REQ_REQ;
+
+ if (!adc->poll_eoc)
+ reinit_completion(&adc->complete);
+
+ ret = adc5_write(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
+ if (ret)
+ return ret;
+
+ ret = adc5_write(adc, ADC5_USR_CONV_REQ, &conv_req, 1);
+
+ return ret;
+}
+
static int adc5_do_conversion(struct adc5_chip *adc,
struct adc5_channel_prop *prop,
struct iio_chan_spec const *chan,
@@ -355,6 +415,44 @@ static int adc5_do_conversion(struct adc5_chip *adc,
return ret;
}
+static int adc7_do_conversion(struct adc5_chip *adc,
+ struct adc5_channel_prop *prop,
+ struct iio_chan_spec const *chan,
+ u16 *data_volt, u16 *data_cur)
+{
+ int ret;
+ u8 status = 0;
+
+ mutex_lock(&adc->lock);
+
+ ret = adc7_configure(adc, prop);
+ if (ret) {
+ pr_err("ADC configure failed with %d\n", ret);
+ goto unlock;
+ }
+
+ /* No support for polling mode at present*/
+ wait_for_completion_timeout(&adc->complete,
+ ADC7_CONV_TIMEOUT);
+
+ ret = adc5_read(adc, ADC5_USR_STATUS1, &status, 1);
+ if (ret < 0)
+ goto unlock;
+
+ if (status & ADC5_USR_STATUS1_CONV_FAULT) {
+ pr_err("Unexpected conversion fault\n");
+ ret = -EIO;
+ goto unlock;
+ }
+
+ ret = adc5_read_voltage_data(adc, data_volt);
+
+unlock:
+ mutex_unlock(&adc->lock);
+
+ return ret;
+}
+
static irqreturn_t adc5_isr(int irq, void *dev_id)
{
struct adc5_chip *adc = dev_id;
@@ -377,6 +475,56 @@ static int adc5_of_xlate(struct iio_dev *indio_dev,
return -EINVAL;
}
+static int adc7_of_xlate(struct iio_dev *indio_dev,
+ const struct of_phandle_args *iiospec)
+{
+ struct adc5_chip *adc = iio_priv(indio_dev);
+ int i, v_channel;
+
+ for (i = 0; i < adc->nchannels; i++) {
+ v_channel = ((adc->chan_props[i].sid << ADC_CHANNEL_OFFSET) |
+ adc->chan_props[i].channel);
+ if (v_channel == iiospec->args[0])
+ return i;
+ }
+
+ return -EINVAL;
+}
+
+static int adc7_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan, int *val, int *val2,
+ long mask)
+{
+ struct adc5_chip *adc = iio_priv(indio_dev);
+ struct adc5_channel_prop *prop;
+ u16 adc_code_volt, adc_code_cur;
+ int ret;
+
+ prop = &adc->chan_props[chan->address];
+
+ switch (mask) {
+ case IIO_CHAN_INFO_PROCESSED:
+ ret = adc7_do_conversion(adc, prop, chan,
+ &adc_code_volt, &adc_code_cur);
+ if (ret)
+ return ret;
+
+ ret = qcom_adc5_hw_scale(prop->scale_fn_type,
+ &adc5_prescale_ratios[prop->prescale],
+ adc->data,
+ adc_code_volt, val);
+
+ if (ret)
+ return ret;
+
+ return IIO_VAL_INT;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
static int adc5_read_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan, int *val, int *val2,
long mask)
@@ -415,6 +563,11 @@ static const struct iio_info adc5_info = {
.of_xlate = adc5_of_xlate,
};
+static const struct iio_info adc7_info = {
+ .read_raw = adc7_read_raw,
+ .of_xlate = adc7_of_xlate,
+};
+
struct adc5_channels {
const char *datasheet_name;
unsigned int prescale_index;
@@ -477,6 +630,39 @@ static const struct adc5_channels adc5_chans_pmic[ADC5_MAX_CHANNEL] = {
SCALE_HW_CALIB_PM5_SMB_TEMP)
};
+static const struct adc5_channels adc7_chans_pmic[ADC5_MAX_CHANNEL] = {
+ [ADC7_REF_GND] = ADC5_CHAN_VOLT("ref_gnd", 0,
+ SCALE_HW_CALIB_DEFAULT)
+ [ADC7_1P25VREF] = ADC5_CHAN_VOLT("vref_1p25", 0,
+ SCALE_HW_CALIB_DEFAULT)
+ [ADC7_VPH_PWR] = ADC5_CHAN_VOLT("vph_pwr", 1,
+ SCALE_HW_CALIB_DEFAULT)
+ [ADC7_VBAT_SNS] = ADC5_CHAN_VOLT("vbat_sns", 3,
+ SCALE_HW_CALIB_DEFAULT)
+ [ADC7_DIE_TEMP] = ADC5_CHAN_TEMP("die_temp", 0,
+ SCALE_HW_CALIB_PMIC_THERM_PM7)
+ [ADC7_AMUX_THM1_100K_PU] = ADC5_CHAN_TEMP("amux_thm1_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+ [ADC7_AMUX_THM2_100K_PU] = ADC5_CHAN_TEMP("amux_thm2_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+ [ADC7_AMUX_THM3_100K_PU] = ADC5_CHAN_TEMP("amux_thm3_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+ [ADC7_AMUX_THM4_100K_PU] = ADC5_CHAN_TEMP("amux_thm4_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+ [ADC7_AMUX_THM5_100K_PU] = ADC5_CHAN_TEMP("amux_thm5_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+ [ADC7_AMUX_THM6_100K_PU] = ADC5_CHAN_TEMP("amux_thm6_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+ [ADC7_GPIO1_100K_PU] = ADC5_CHAN_TEMP("gpio1_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+ [ADC7_GPIO2_100K_PU] = ADC5_CHAN_TEMP("gpio2_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+ [ADC7_GPIO3_100K_PU] = ADC5_CHAN_TEMP("gpio3_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+ [ADC7_GPIO4_100K_PU] = ADC5_CHAN_TEMP("gpio4_pu2", 0,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7)
+};
+
static const struct adc5_channels adc5_chans_rev2[ADC5_MAX_CHANNEL] = {
[ADC5_REF_GND] = ADC5_CHAN_VOLT("ref_gnd", 0,
SCALE_HW_CALIB_DEFAULT)
@@ -511,6 +697,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
{
const char *name = node->name, *channel_name;
u32 chan, value, varr[2];
+ u32 sid = 0;
int ret;
struct device *dev = adc->dev;
@@ -520,6 +707,15 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
return ret;
}
+ /*
+ * Value read from "reg" is virtual channel number
+ * virtual channel number = (sid << 8 | channel number).
+ */
+ if (adc->is_pmic7) {
+ sid = (chan >> ADC_CHANNEL_OFFSET);
+ chan = (chan & ADC_CHANNEL_MASK);
+ }
+
if (chan > ADC5_PARALLEL_ISENSE_VBAT_IDATA ||
!data->adc_chans[chan].datasheet_name) {
dev_err(dev, "%s invalid channel number %d\n", name, chan);
@@ -528,6 +724,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
/* the channel has DT description */
prop->channel = chan;
+ prop->sid = sid;
channel_name = of_get_property(node,
"label", NULL) ? : node->name;
@@ -578,8 +775,9 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
pr_debug("dig_ver:minor:%d, major:%d\n", dig_version[0],
dig_version[1]);
/* Digital controller >= 5.3 have hw_settle_2 option */
- if (dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
- dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR)
+ if ((dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
+ dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR) ||
+ (adc->is_pmic7))
ret = adc5_hw_settle_time_from_dt(value,
data->hw_settle_2);
else
@@ -639,6 +837,17 @@ static const struct adc5_data adc5_data_pmic = {
1, 2, 4, 8, 16, 32, 64, 128},
};
+static const struct adc5_data adc7_data_pmic = {
+ .full_scale_code_volt = 0x70e4,
+ .adc_chans = adc7_chans_pmic,
+ .decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
+ {85, 340, 1360},
+ .hw_settle_2 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
+ {15, 100, 200, 300, 400, 500, 600, 700,
+ 1000, 2000, 4000, 8000, 16000, 32000,
+ 64000, 128000},
+};
+
static const struct adc5_data adc5_data_pmic_rev2 = {
.full_scale_code_volt = 0x4000,
.full_scale_code_cur = 0x1800,
@@ -659,6 +868,10 @@ static const struct of_device_id adc5_match_table[] = {
.data = &adc5_data_pmic,
},
{
+ .compatible = "qcom,spmi-adc7",
+ .data = &adc7_data_pmic,
+ },
+ {
.compatible = "qcom,spmi-adc-rev2",
.data = &adc5_data_pmic_rev2,
},
@@ -752,6 +965,16 @@ static int adc5_probe(struct platform_device *pdev)
adc->regmap = regmap;
adc->dev = dev;
adc->base = reg;
+
+ platform_set_drvdata(pdev, adc);
+
+ if (of_device_is_compatible(node, "qcom,spmi-adc7")) {
+ indio_dev->info = &adc7_info;
+ adc->is_pmic7 = true;
+ } else {
+ indio_dev->info = &adc5_info;
+ }
+
init_completion(&adc->complete);
mutex_init(&adc->lock);
@@ -777,19 +1000,27 @@ static int adc5_probe(struct platform_device *pdev)
indio_dev->dev.of_node = node;
indio_dev->name = pdev->name;
indio_dev->modes = INDIO_DIRECT_MODE;
- indio_dev->info = &adc5_info;
indio_dev->channels = adc->iio_chans;
indio_dev->num_channels = adc->nchannels;
return devm_iio_device_register(dev, indio_dev);
}
+static int adc5_exit(struct platform_device *pdev)
+{
+ struct adc5_chip *adc = platform_get_drvdata(pdev);
+
+ mutex_destroy(&adc->lock);
+ return 0;
+}
+
static struct platform_driver adc5_driver = {
.driver = {
.name = "qcom-spmi-adc5.c",
.of_match_table = adc5_match_table,
},
.probe = adc5_probe,
+ .remove = adc5_exit,
};
module_platform_driver(adc5_driver);
diff --git a/drivers/iio/adc/qcom-vadc-common.c b/drivers/iio/adc/qcom-vadc-common.c
index 2bb78d1..43d2473 100644
--- a/drivers/iio/adc/qcom-vadc-common.c
+++ b/drivers/iio/adc/qcom-vadc-common.c
@@ -89,6 +89,195 @@ static const struct vadc_map_pt adcmap_100k_104ef_104fb_1875_vref[] = {
{ 46, 125000 },
};
+static const struct vadc_map_pt adcmap7_die_temp[] = {
+ { 433700, 1967},
+ { 473100, 1964},
+ { 512400, 1957},
+ { 551500, 1949},
+ { 590500, 1940},
+ { 629300, 1930},
+ { 667900, 1921},
+ { 706400, 1910},
+ { 744600, 1896},
+ { 782500, 1878},
+ { 820100, 1859},
+ { 857300, 0},
+};
+
+/*
+ * Resistance to temperature table for 100k pull up for NTCG104EF104.
+ */
+static const struct vadc_map_pt adcmap7_100k[] = {
+ { 4250657, -40960 },
+ { 3962085, -39936 },
+ { 3694875, -38912 },
+ { 3447322, -37888 },
+ { 3217867, -36864 },
+ { 3005082, -35840 },
+ { 2807660, -34816 },
+ { 2624405, -33792 },
+ { 2454218, -32768 },
+ { 2296094, -31744 },
+ { 2149108, -30720 },
+ { 2012414, -29696 },
+ { 1885232, -28672 },
+ { 1766846, -27648 },
+ { 1656598, -26624 },
+ { 1553884, -25600 },
+ { 1458147, -24576 },
+ { 1368873, -23552 },
+ { 1285590, -22528 },
+ { 1207863, -21504 },
+ { 1135290, -20480 },
+ { 1067501, -19456 },
+ { 1004155, -18432 },
+ { 944935, -17408 },
+ { 889550, -16384 },
+ { 837731, -15360 },
+ { 789229, -14336 },
+ { 743813, -13312 },
+ { 701271, -12288 },
+ { 661405, -11264 },
+ { 624032, -10240 },
+ { 588982, -9216 },
+ { 556100, -8192 },
+ { 525239, -7168 },
+ { 496264, -6144 },
+ { 469050, -5120 },
+ { 443480, -4096 },
+ { 419448, -3072 },
+ { 396851, -2048 },
+ { 375597, -1024 },
+ { 355598, 0 },
+ { 336775, 1024 },
+ { 319052, 2048 },
+ { 302359, 3072 },
+ { 286630, 4096 },
+ { 271806, 5120 },
+ { 257829, 6144 },
+ { 244646, 7168 },
+ { 232209, 8192 },
+ { 220471, 9216 },
+ { 209390, 10240 },
+ { 198926, 11264 },
+ { 189040, 12288 },
+ { 179698, 13312 },
+ { 170868, 14336 },
+ { 162519, 15360 },
+ { 154622, 16384 },
+ { 147150, 17408 },
+ { 140079, 18432 },
+ { 133385, 19456 },
+ { 127046, 20480 },
+ { 121042, 21504 },
+ { 115352, 22528 },
+ { 109960, 23552 },
+ { 104848, 24576 },
+ { 100000, 25600 },
+ { 95402, 26624 },
+ { 91038, 27648 },
+ { 86897, 28672 },
+ { 82965, 29696 },
+ { 79232, 30720 },
+ { 75686, 31744 },
+ { 72316, 32768 },
+ { 69114, 33792 },
+ { 66070, 34816 },
+ { 63176, 35840 },
+ { 60423, 36864 },
+ { 57804, 37888 },
+ { 55312, 38912 },
+ { 52940, 39936 },
+ { 50681, 40960 },
+ { 48531, 41984 },
+ { 46482, 43008 },
+ { 44530, 44032 },
+ { 42670, 45056 },
+ { 40897, 46080 },
+ { 39207, 47104 },
+ { 37595, 48128 },
+ { 36057, 49152 },
+ { 34590, 50176 },
+ { 33190, 51200 },
+ { 31853, 52224 },
+ { 30577, 53248 },
+ { 29358, 54272 },
+ { 28194, 55296 },
+ { 27082, 56320 },
+ { 26020, 57344 },
+ { 25004, 58368 },
+ { 24033, 59392 },
+ { 23104, 60416 },
+ { 22216, 61440 },
+ { 21367, 62464 },
+ { 20554, 63488 },
+ { 19776, 64512 },
+ { 19031, 65536 },
+ { 18318, 66560 },
+ { 17636, 67584 },
+ { 16982, 68608 },
+ { 16355, 69632 },
+ { 15755, 70656 },
+ { 15180, 71680 },
+ { 14628, 72704 },
+ { 14099, 73728 },
+ { 13592, 74752 },
+ { 13106, 75776 },
+ { 12640, 76800 },
+ { 12192, 77824 },
+ { 11762, 78848 },
+ { 11350, 79872 },
+ { 10954, 80896 },
+ { 10574, 81920 },
+ { 10209, 82944 },
+ { 9858, 83968 },
+ { 9521, 84992 },
+ { 9197, 86016 },
+ { 8886, 87040 },
+ { 8587, 88064 },
+ { 8299, 89088 },
+ { 8023, 90112 },
+ { 7757, 91136 },
+ { 7501, 92160 },
+ { 7254, 93184 },
+ { 7017, 94208 },
+ { 6789, 95232 },
+ { 6570, 96256 },
+ { 6358, 97280 },
+ { 6155, 98304 },
+ { 5959, 99328 },
+ { 5770, 100352 },
+ { 5588, 101376 },
+ { 5412, 102400 },
+ { 5243, 103424 },
+ { 5080, 104448 },
+ { 4923, 105472 },
+ { 4771, 106496 },
+ { 4625, 107520 },
+ { 4484, 108544 },
+ { 4348, 109568 },
+ { 4217, 110592 },
+ { 4090, 111616 },
+ { 3968, 112640 },
+ { 3850, 113664 },
+ { 3736, 114688 },
+ { 3626, 115712 },
+ { 3519, 116736 },
+ { 3417, 117760 },
+ { 3317, 118784 },
+ { 3221, 119808 },
+ { 3129, 120832 },
+ { 3039, 121856 },
+ { 2952, 122880 },
+ { 2868, 123904 },
+ { 2787, 124928 },
+ { 2709, 125952 },
+ { 2633, 126976 },
+ { 2560, 128000 },
+ { 2489, 129024 },
+ { 2420, 130048 }
+};
+
static int qcom_vadc_scale_hw_calib_volt(
const struct vadc_prescale_ratio *prescale,
const struct adc5_data *data,
@@ -97,6 +286,10 @@ static int qcom_vadc_scale_hw_calib_therm(
const struct vadc_prescale_ratio *prescale,
const struct adc5_data *data,
u16 adc_code, int *result_mdec);
+static int qcom_vadc7_scale_hw_calib_therm(
+ const struct vadc_prescale_ratio *prescale,
+ const struct adc5_data *data,
+ u16 adc_code, int *result_mdec);
static int qcom_vadc_scale_hw_smb_temp(
const struct vadc_prescale_ratio *prescale,
const struct adc5_data *data,
@@ -109,12 +302,20 @@ static int qcom_vadc_scale_hw_calib_die_temp(
const struct vadc_prescale_ratio *prescale,
const struct adc5_data *data,
u16 adc_code, int *result_mdec);
+static int qcom_vadc7_scale_hw_calib_die_temp(
+ const struct vadc_prescale_ratio *prescale,
+ const struct adc5_data *data,
+ u16 adc_code, int *result_mdec);
static struct qcom_adc5_scale_type scale_adc5_fn[] = {
[SCALE_HW_CALIB_DEFAULT] = {qcom_vadc_scale_hw_calib_volt},
[SCALE_HW_CALIB_THERM_100K_PULLUP] = {qcom_vadc_scale_hw_calib_therm},
[SCALE_HW_CALIB_XOTHERM] = {qcom_vadc_scale_hw_calib_therm},
+ [SCALE_HW_CALIB_THERM_100K_PU_PM7] = {
+ qcom_vadc7_scale_hw_calib_therm},
[SCALE_HW_CALIB_PMIC_THERM] = {qcom_vadc_scale_hw_calib_die_temp},
+ [SCALE_HW_CALIB_PMIC_THERM_PM7] = {
+ qcom_vadc7_scale_hw_calib_die_temp},
[SCALE_HW_CALIB_PM5_CHG_TEMP] = {qcom_vadc_scale_hw_chg5_temp},
[SCALE_HW_CALIB_PM5_SMB_TEMP] = {qcom_vadc_scale_hw_smb_temp},
};
@@ -291,6 +492,32 @@ static int qcom_vadc_scale_code_voltage_factor(u16 adc_code,
return (int) voltage;
}
+static int qcom_vadc7_scale_hw_calib_therm(
+ const struct vadc_prescale_ratio *prescale,
+ const struct adc5_data *data,
+ u16 adc_code, int *result_mdec)
+{
+ s64 resistance = 0;
+ int ret, result = 0;
+
+ if (adc_code >= RATIO_MAX_ADC7)
+ return -EINVAL;
+
+ /* (ADC code * R_PULLUP (100Kohm)) / (full_scale_code - ADC code)*/
+ resistance = (s64) adc_code * R_PU_100K;
+ resistance = div64_s64(resistance, (RATIO_MAX_ADC7 - adc_code));
+
+ ret = qcom_vadc_map_voltage_temp(adcmap7_100k,
+ ARRAY_SIZE(adcmap7_100k),
+ resistance, &result);
+ if (ret)
+ return ret;
+
+ *result_mdec = result;
+
+ return 0;
+}
+
static int qcom_vadc_scale_hw_calib_volt(
const struct vadc_prescale_ratio *prescale,
const struct adc5_data *data,
@@ -330,6 +557,39 @@ static int qcom_vadc_scale_hw_calib_die_temp(
return 0;
}
+static int qcom_vadc7_scale_hw_calib_die_temp(
+ const struct vadc_prescale_ratio *prescale,
+ const struct adc5_data *data,
+ u16 adc_code, int *result_mdec)
+{
+
+ int voltage, vtemp0, temp, i = 0;
+
+ voltage = qcom_vadc_scale_code_voltage_factor(adc_code,
+ prescale, data, 1);
+
+ while (i < ARRAY_SIZE(adcmap7_die_temp)) {
+ if (adcmap7_die_temp[i].x > voltage)
+ break;
+ i++;
+ }
+
+ if (i == 0) {
+ *result_mdec = DIE_TEMP_ADC7_SCALE_1;
+ } else if (i == ARRAY_SIZE(adcmap7_die_temp)) {
+ *result_mdec = DIE_TEMP_ADC7_MAX;
+ } else {
+ vtemp0 = adcmap7_die_temp[i-1].x;
+ voltage = voltage - vtemp0;
+ temp = div64_s64(voltage * DIE_TEMP_ADC7_SCALE_FACTOR,
+ adcmap7_die_temp[i-1].y);
+ temp += DIE_TEMP_ADC7_SCALE_1 + (DIE_TEMP_ADC7_SCALE_2 * (i-1));
+ *result_mdec = temp;
+ }
+
+ return 0;
+}
+
static int qcom_vadc_scale_hw_smb_temp(
const struct vadc_prescale_ratio *prescale,
const struct adc5_data *data,
diff --git a/drivers/iio/adc/qcom-vadc-common.h b/drivers/iio/adc/qcom-vadc-common.h
index e074902a..5f9e680 100644
--- a/drivers/iio/adc/qcom-vadc-common.h
+++ b/drivers/iio/adc/qcom-vadc-common.h
@@ -49,6 +49,14 @@
#define ADC5_FULL_SCALE_CODE 0x70e4
#define ADC5_USR_DATA_CHECK 0x8000
+#define R_PU_100K 100000
+#define RATIO_MAX_ADC7 0x4000
+
+#define DIE_TEMP_ADC7_SCALE_1 -60000
+#define DIE_TEMP_ADC7_SCALE_2 20000
+#define DIE_TEMP_ADC7_SCALE_FACTOR 1000
+#define DIE_TEMP_ADC7_MAX 160000
+
/**
* struct vadc_map_pt - Map the graph representation for ADC channel
* @x: Represent the ADC digitized code.
@@ -110,8 +118,12 @@ struct vadc_prescale_ratio {
* lookup table. The hardware applies offset/slope to adc code.
* SCALE_HW_CALIB_XOTHERM: Returns XO thermistor voltage in millidegC using
* 100k pullup. The hardware applies offset/slope to adc code.
+ * SCALE_HW_CALIB_THERM_100K_PU_PM7: Returns temperature in millidegC using
+ * lookup table for PMIC7. The hardware applies offset/slope to adc code.
* SCALE_HW_CALIB_PMIC_THERM: Returns result in milli degree's Centigrade.
* The hardware applies offset/slope to adc code.
+ * SCALE_HW_CALIB_PMIC_THERM: Returns result in milli degree's Centigrade.
+ * The hardware applies offset/slope to adc code. This is for PMIC7.
* SCALE_HW_CALIB_PM5_CHG_TEMP: Returns result in millidegrees for PMIC5
* charger temperature.
* SCALE_HW_CALIB_PM5_SMB_TEMP: Returns result in millidegrees for PMIC5
@@ -126,7 +138,9 @@ enum vadc_scale_fn_type {
SCALE_HW_CALIB_DEFAULT,
SCALE_HW_CALIB_THERM_100K_PULLUP,
SCALE_HW_CALIB_XOTHERM,
+ SCALE_HW_CALIB_THERM_100K_PU_PM7,
SCALE_HW_CALIB_PMIC_THERM,
+ SCALE_HW_CALIB_PMIC_THERM_PM7,
SCALE_HW_CALIB_PM5_CHG_TEMP,
SCALE_HW_CALIB_PM5_SMB_TEMP,
SCALE_HW_CALIB_INVALID,
diff --git a/include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h b/include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h
new file mode 100644
index 0000000..9426f27
--- /dev/null
+++ b/include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h
@@ -0,0 +1,67 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_QCOM_SPMI_VADC_PM8350_H
+#define _DT_BINDINGS_QCOM_SPMI_VADC_PM8350_H
+
+#ifndef PM8350_SID
+#define PM8350_SID 1
+#endif
+
+/* ADC channels for PM8350_ADC for PMIC7 */
+#define PM8350_ADC7_REF_GND (PM8350_SID << 8 | 0x0)
+#define PM8350_ADC7_1P25VREF (PM8350_SID << 8 | 0x01)
+#define PM8350_ADC7_VREF_VADC (PM8350_SID << 8 | 0x02)
+#define PM8350_ADC7_DIE_TEMP (PM8350_SID << 8 | 0x03)
+
+#define PM8350_ADC7_AMUX_THM1 (PM8350_SID << 8 | 0x04)
+#define PM8350_ADC7_AMUX_THM2 (PM8350_SID << 8 | 0x05)
+#define PM8350_ADC7_AMUX_THM3 (PM8350_SID << 8 | 0x06)
+#define PM8350_ADC7_AMUX_THM4 (PM8350_SID << 8 | 0x07)
+#define PM8350_ADC7_AMUX_THM5 (PM8350_SID << 8 | 0x08)
+#define PM8350_ADC7_GPIO1 (PM8350_SID << 8 | 0x0a)
+#define PM8350_ADC7_GPIO2 (PM8350_SID << 8 | 0x0b)
+#define PM8350_ADC7_GPIO3 (PM8350_SID << 8 | 0x0c)
+#define PM8350_ADC7_GPIO4 (PM8350_SID << 8 | 0x0d)
+
+/* 30k pull-up1 */
+#define PM8350_ADC7_AMUX_THM1_30K_PU (PM8350_SID << 8 | 0x24)
+#define PM8350_ADC7_AMUX_THM2_30K_PU (PM8350_SID << 8 | 0x25)
+#define PM8350_ADC7_AMUX_THM3_30K_PU (PM8350_SID << 8 | 0x26)
+#define PM8350_ADC7_AMUX_THM4_30K_PU (PM8350_SID << 8 | 0x27)
+#define PM8350_ADC7_AMUX_THM5_30K_PU (PM8350_SID << 8 | 0x28)
+#define PM8350_ADC7_GPIO1_30K_PU (PM8350_SID << 8 | 0x2a)
+#define PM8350_ADC7_GPIO2_30K_PU (PM8350_SID << 8 | 0x2b)
+#define PM8350_ADC7_GPIO3_30K_PU (PM8350_SID << 8 | 0x2c)
+#define PM8350_ADC7_GPIO4_30K_PU (PM8350_SID << 8 | 0x2d)
+
+/* 100k pull-up2 */
+#define PM8350_ADC7_AMUX_THM1_100K_PU (PM8350_SID << 8 | 0x44)
+#define PM8350_ADC7_AMUX_THM2_100K_PU (PM8350_SID << 8 | 0x45)
+#define PM8350_ADC7_AMUX_THM3_100K_PU (PM8350_SID << 8 | 0x46)
+#define PM8350_ADC7_AMUX_THM4_100K_PU (PM8350_SID << 8 | 0x47)
+#define PM8350_ADC7_AMUX_THM5_100K_PU (PM8350_SID << 8 | 0x48)
+#define PM8350_ADC7_GPIO1_100K_PU (PM8350_SID << 8 | 0x4a)
+#define PM8350_ADC7_GPIO2_100K_PU (PM8350_SID << 8 | 0x4b)
+#define PM8350_ADC7_GPIO3_100K_PU (PM8350_SID << 8 | 0x4c)
+#define PM8350_ADC7_GPIO4_100K_PU (PM8350_SID << 8 | 0x4d)
+
+/* 400k pull-up3 */
+#define PM8350_ADC7_AMUX_THM1_400K_PU (PM8350_SID << 8 | 0x64)
+#define PM8350_ADC7_AMUX_THM2_400K_PU (PM8350_SID << 8 | 0x65)
+#define PM8350_ADC7_AMUX_THM3_400K_PU (PM8350_SID << 8 | 0x66)
+#define PM8350_ADC7_AMUX_THM4_400K_PU (PM8350_SID << 8 | 0x67)
+#define PM8350_ADC7_AMUX_THM5_400K_PU (PM8350_SID << 8 | 0x68)
+#define PM8350_ADC7_GPIO1_400K_PU (PM8350_SID << 8 | 0x6a)
+#define PM8350_ADC7_GPIO2_400K_PU (PM8350_SID << 8 | 0x6b)
+#define PM8350_ADC7_GPIO3_400K_PU (PM8350_SID << 8 | 0x6c)
+#define PM8350_ADC7_GPIO4_400K_PU (PM8350_SID << 8 | 0x6d)
+
+/* 1/3 Divider */
+#define PM8350_ADC7_GPIO4_DIV3 (PM8350_SID << 8 | 0x8d)
+
+#define PM8350_ADC7_VPH_PWR (PM8350_SID << 8 | 0x8e)
+
+#endif /* _DT_BINDINGS_QCOM_SPMI_VADC_PM8350_H */
diff --git a/include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h b/include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h
new file mode 100644
index 0000000..dc2497c
--- /dev/null
+++ b/include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h
@@ -0,0 +1,88 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2020 The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_QCOM_SPMI_VADC_PM8350B_H
+#define _DT_BINDINGS_QCOM_SPMI_VADC_PM8350B_H
+
+#ifndef PM8350B_SID
+#define PM8350B_SID 3
+#endif
+
+/* ADC channels for PM8350B_ADC for PMIC7 */
+#define PM8350B_ADC7_REF_GND (PM8350B_SID << 8 | 0x0)
+#define PM8350B_ADC7_1P25VREF (PM8350B_SID << 8 | 0x01)
+#define PM8350B_ADC7_VREF_VADC (PM8350B_SID << 8 | 0x02)
+#define PM8350B_ADC7_DIE_TEMP (PM8350B_SID << 8 | 0x03)
+
+#define PM8350B_ADC7_AMUX_THM1 (PM8350B_SID << 8 | 0x04)
+#define PM8350B_ADC7_AMUX_THM2 (PM8350B_SID << 8 | 0x05)
+#define PM8350B_ADC7_AMUX_THM3 (PM8350B_SID << 8 | 0x06)
+#define PM8350B_ADC7_AMUX_THM4 (PM8350B_SID << 8 | 0x07)
+#define PM8350B_ADC7_AMUX_THM5 (PM8350B_SID << 8 | 0x08)
+#define PM8350B_ADC7_AMUX_THM6 (PM8350B_SID << 8 | 0x09)
+#define PM8350B_ADC7_GPIO1 (PM8350B_SID << 8 | 0x0a)
+#define PM8350B_ADC7_GPIO2 (PM8350B_SID << 8 | 0x0b)
+#define PM8350B_ADC7_GPIO3 (PM8350B_SID << 8 | 0x0c)
+#define PM8350B_ADC7_GPIO4 (PM8350B_SID << 8 | 0x0d)
+
+#define PM8350B_ADC7_CHG_TEMP (PM8350B_SID << 8 | 0x10)
+#define PM8350B_ADC7_USB_IN_V_16 (PM8350B_SID << 8 | 0x11)
+#define PM8350B_ADC7_VDC_16 (PM8350B_SID << 8 | 0x12)
+#define PM8350B_ADC7_CC1_ID (PM8350B_SID << 8 | 0x13)
+#define PM8350B_ADC7_VREF_BAT_THERM (PM8350B_SID << 8 | 0x15)
+#define PM8350B_ADC7_IIN_FB (PM8350B_SID << 8 | 0x17)
+
+/* 30k pull-up1 */
+#define PM8350B_ADC7_AMUX_THM1_30K_PU (PM8350B_SID << 8 | 0x24)
+#define PM8350B_ADC7_AMUX_THM2_30K_PU (PM8350B_SID << 8 | 0x25)
+#define PM8350B_ADC7_AMUX_THM3_30K_PU (PM8350B_SID << 8 | 0x26)
+#define PM8350B_ADC7_AMUX_THM4_30K_PU (PM8350B_SID << 8 | 0x27)
+#define PM8350B_ADC7_AMUX_THM5_30K_PU (PM8350B_SID << 8 | 0x28)
+#define PM8350B_ADC7_AMUX_THM6_30K_PU (PM8350B_SID << 8 | 0x29)
+#define PM8350B_ADC7_GPIO1_30K_PU (PM8350B_SID << 8 | 0x2a)
+#define PM8350B_ADC7_GPIO2_30K_PU (PM8350B_SID << 8 | 0x2b)
+#define PM8350B_ADC7_GPIO3_30K_PU (PM8350B_SID << 8 | 0x2c)
+#define PM8350B_ADC7_GPIO4_30K_PU (PM8350B_SID << 8 | 0x2d)
+#define PM8350B_ADC7_CC1_ID_30K_PU (PM8350B_SID << 8 | 0x33)
+
+/* 100k pull-up2 */
+#define PM8350B_ADC7_AMUX_THM1_100K_PU (PM8350B_SID << 8 | 0x44)
+#define PM8350B_ADC7_AMUX_THM2_100K_PU (PM8350B_SID << 8 | 0x45)
+#define PM8350B_ADC7_AMUX_THM3_100K_PU (PM8350B_SID << 8 | 0x46)
+#define PM8350B_ADC7_AMUX_THM4_100K_PU (PM8350B_SID << 8 | 0x47)
+#define PM8350B_ADC7_AMUX_THM5_100K_PU (PM8350B_SID << 8 | 0x48)
+#define PM8350B_ADC7_AMUX_THM6_100K_PU (PM8350B_SID << 8 | 0x49)
+#define PM8350B_ADC7_GPIO1_100K_PU (PM8350B_SID << 8 | 0x4a)
+#define PM8350B_ADC7_GPIO2_100K_PU (PM8350B_SID << 8 | 0x4b)
+#define PM8350B_ADC7_GPIO3_100K_PU (PM8350B_SID << 8 | 0x4c)
+#define PM8350B_ADC7_GPIO4_100K_PU (PM8350B_SID << 8 | 0x4d)
+#define PM8350B_ADC7_CC1_ID_100K_PU (PM8350B_SID << 8 | 0x53)
+
+/* 400k pull-up3 */
+#define PM8350B_ADC7_AMUX_THM1_400K_PU (PM8350B_SID << 8 | 0x64)
+#define PM8350B_ADC7_AMUX_THM2_400K_PU (PM8350B_SID << 8 | 0x65)
+#define PM8350B_ADC7_AMUX_THM3_400K_PU (PM8350B_SID << 8 | 0x66)
+#define PM8350B_ADC7_AMUX_THM4_400K_PU (PM8350B_SID << 8 | 0x67)
+#define PM8350B_ADC7_AMUX_THM5_400K_PU (PM8350B_SID << 8 | 0x68)
+#define PM8350B_ADC7_AMUX_THM6_400K_PU (PM8350B_SID << 8 | 0x69)
+#define PM8350B_ADC7_GPIO1_400K_PU (PM8350B_SID << 8 | 0x6a)
+#define PM8350B_ADC7_GPIO2_400K_PU (PM8350B_SID << 8 | 0x6b)
+#define PM8350B_ADC7_GPIO3_400K_PU (PM8350B_SID << 8 | 0x6c)
+#define PM8350B_ADC7_GPIO4_400K_PU (PM8350B_SID << 8 | 0x6d)
+#define PM8350B_ADC7_CC1_ID_400K_PU (PM8350B_SID << 8 | 0x73)
+
+/* 1/3 Divider */
+#define PM8350B_ADC7_GPIO1_DIV3 (PM8350B_SID << 8 | 0x8a)
+#define PM8350B_ADC7_GPIO2_DIV3 (PM8350B_SID << 8 | 0x8b)
+#define PM8350B_ADC7_GPIO3_DIV3 (PM8350B_SID << 8 | 0x8c)
+#define PM8350B_ADC7_GPIO4_DIV3 (PM8350B_SID << 8 | 0x8d)
+
+#define PM8350B_ADC7_VPH_PWR (PM8350B_SID << 8 | 0x8e)
+#define PM8350B_ADC7_VBAT_SNS (PM8350B_SID << 8 | 0x8f)
+
+#define PM8350B_ADC7_SBUx (PM8350B_SID << 8 | 0x94)
+#define PM8350B_ADC7_VBAT_2S_MID (PM8350B_SID << 8 | 0x96)
+
+#endif /* _DT_BINDINGS_QCOM_SPMI_VADC_PM8350B_H */
diff --git a/include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h b/include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h
new file mode 100644
index 0000000..6c29687
--- /dev/null
+++ b/include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h
@@ -0,0 +1,46 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2020 The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_QCOM_SPMI_VADC_PMK8350_H
+#define _DT_BINDINGS_QCOM_SPMI_VADC_PMK8350_H
+
+#ifndef PMK8350_SID
+#define PMK8350_SID 0
+#endif
+
+/* ADC channels for PMK8350_ADC for PMIC7 */
+#define PMK8350_ADC7_REF_GND (PMK8350_SID << 8 | 0x0)
+#define PMK8350_ADC7_1P25VREF (PMK8350_SID << 8 | 0x01)
+#define PMK8350_ADC7_VREF_VADC (PMK8350_SID << 8 | 0x02)
+#define PMK8350_ADC7_DIE_TEMP (PMK8350_SID << 8 | 0x03)
+
+#define PMK8350_ADC7_AMUX_THM1 (PMK8350_SID << 8 | 0x04)
+#define PMK8350_ADC7_AMUX_THM2 (PMK8350_SID << 8 | 0x05)
+#define PMK8350_ADC7_AMUX_THM3 (PMK8350_SID << 8 | 0x06)
+#define PMK8350_ADC7_AMUX_THM4 (PMK8350_SID << 8 | 0x07)
+#define PMK8350_ADC7_AMUX_THM5 (PMK8350_SID << 8 | 0x08)
+
+/* 30k pull-up1 */
+#define PMK8350_ADC7_AMUX_THM1_30K_PU (PMK8350_SID << 8 | 0x24)
+#define PMK8350_ADC7_AMUX_THM2_30K_PU (PMK8350_SID << 8 | 0x25)
+#define PMK8350_ADC7_AMUX_THM3_30K_PU (PMK8350_SID << 8 | 0x26)
+#define PMK8350_ADC7_AMUX_THM4_30K_PU (PMK8350_SID << 8 | 0x27)
+#define PMK8350_ADC7_AMUX_THM5_30K_PU (PMK8350_SID << 8 | 0x28)
+
+/* 100k pull-up2 */
+#define PMK8350_ADC7_AMUX_THM1_100K_PU (PMK8350_SID << 8 | 0x44)
+#define PMK8350_ADC7_AMUX_THM2_100K_PU (PMK8350_SID << 8 | 0x45)
+#define PMK8350_ADC7_AMUX_THM3_100K_PU (PMK8350_SID << 8 | 0x46)
+#define PMK8350_ADC7_AMUX_THM4_100K_PU (PMK8350_SID << 8 | 0x47)
+#define PMK8350_ADC7_AMUX_THM5_100K_PU (PMK8350_SID << 8 | 0x48)
+
+/* 400k pull-up3 */
+#define PMK8350_ADC7_AMUX_THM1_400K_PU (PMK8350_SID << 8 | 0x64)
+#define PMK8350_ADC7_AMUX_THM2_400K_PU (PMK8350_SID << 8 | 0x65)
+#define PMK8350_ADC7_AMUX_THM3_400K_PU (PMK8350_SID << 8 | 0x66)
+#define PMK8350_ADC7_AMUX_THM4_400K_PU (PMK8350_SID << 8 | 0x67)
+#define PMK8350_ADC7_AMUX_THM5_400K_PU (PMK8350_SID << 8 | 0x68)
+
+#endif /* _DT_BINDINGS_QCOM_SPMI_VADC_PMK8350_H */
diff --git a/include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h b/include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h
new file mode 100644
index 0000000..d6df1b1
--- /dev/null
+++ b/include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2020 The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_QCOM_SPMI_VADC_PMR735A_H
+#define _DT_BINDINGS_QCOM_SPMI_VADC_PMR735A_H
+
+#ifndef PMR735A_SID
+#define PMR735A_SID 4
+#endif
+
+/* ADC channels for PMR735A_ADC for PMIC7 */
+#define PMR735A_ADC7_REF_GND (PMR735A_SID << 8 | 0x0)
+#define PMR735A_ADC7_1P25VREF (PMR735A_SID << 8 | 0x01)
+#define PMR735A_ADC7_VREF_VADC (PMR735A_SID << 8 | 0x02)
+#define PMR735A_ADC7_DIE_TEMP (PMR735A_SID << 8 | 0x03)
+
+#define PMR735A_ADC7_GPIO1 (PMR735A_SID << 8 | 0x0a)
+#define PMR735A_ADC7_GPIO2 (PMR735A_SID << 8 | 0x0b)
+#define PMR735A_ADC7_GPIO3 (PMR735A_SID << 8 | 0x0c)
+
+/* 100k pull-up2 */
+#define PMR735A_ADC7_GPIO1_100K_PU (PMR735A_SID << 8 | 0x4a)
+#define PMR735A_ADC7_GPIO2_100K_PU (PMR735A_SID << 8 | 0x4b)
+#define PMR735A_ADC7_GPIO3_100K_PU (PMR735A_SID << 8 | 0x4c)
+
+#endif /* _DT_BINDINGS_QCOM_SPMI_VADC_PMR735A_H */
diff --git a/include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h b/include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h
new file mode 100644
index 0000000..8da0e7d
--- /dev/null
+++ b/include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2020 The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_QCOM_SPMI_VADC_PMR735B_H
+#define _DT_BINDINGS_QCOM_SPMI_VADC_PMR735B_H
+
+#ifndef PMR735B_SID
+#define PMR735B_SID 5
+#endif
+
+/* ADC channels for PMR735B_ADC for PMIC7 */
+#define PMR735B_ADC7_REF_GND (PMR735B_SID << 8 | 0x0)
+#define PMR735B_ADC7_1P25VREF (PMR735B_SID << 8 | 0x01)
+#define PMR735B_ADC7_VREF_VADC (PMR735B_SID << 8 | 0x02)
+#define PMR735B_ADC7_DIE_TEMP (PMR735B_SID << 8 | 0x03)
+
+#define PMR735B_ADC7_GPIO1 (PMR735B_SID << 8 | 0x0a)
+#define PMR735B_ADC7_GPIO2 (PMR735B_SID << 8 | 0x0b)
+#define PMR735B_ADC7_GPIO3 (PMR735B_SID << 8 | 0x0c)
+
+/* 100k pull-up2 */
+#define PMR735B_ADC7_GPIO1_100K_PU (PMR735B_SID << 8 | 0x4a)
+#define PMR735B_ADC7_GPIO2_100K_PU (PMR735B_SID << 8 | 0x4b)
+#define PMR735B_ADC7_GPIO3_100K_PU (PMR735B_SID << 8 | 0x4c)
+
+#endif /* _DT_BINDINGS_QCOM_SPMI_VADC_PMR735B_H */
diff --git a/include/dt-bindings/iio/qcom,spmi-vadc.h b/include/dt-bindings/iio/qcom,spmi-vadc.h
index 61d556d..08adfe2 100644
--- a/include/dt-bindings/iio/qcom,spmi-vadc.h
+++ b/include/dt-bindings/iio/qcom,spmi-vadc.h
@@ -1,6 +1,6 @@
/* SPDX-License-Identifier: GPL-2.0 */
/*
- * Copyright (c) 2012-2014,2018 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2012-2014,2018,2020 The Linux Foundation. All rights reserved.
*/
#ifndef _DT_BINDINGS_QCOM_SPMI_VADC_H
@@ -221,4 +221,80 @@
#define ADC5_MAX_CHANNEL 0xc0
+/* ADC channels for ADC for PMIC7 */
+
+#define ADC7_REF_GND 0x00
+#define ADC7_1P25VREF 0x01
+#define ADC7_VREF_VADC 0x02
+#define ADC7_DIE_TEMP 0x03
+
+#define ADC7_AMUX_THM1 0x04
+#define ADC7_AMUX_THM2 0x05
+#define ADC7_AMUX_THM3 0x06
+#define ADC7_AMUX_THM4 0x07
+#define ADC7_AMUX_THM5 0x08
+#define ADC7_AMUX_THM6 0x09
+#define ADC7_GPIO1 0x0a
+#define ADC7_GPIO2 0x0b
+#define ADC7_GPIO3 0x0c
+#define ADC7_GPIO4 0x0d
+
+#define ADC7_CHG_TEMP 0x10
+#define ADC7_USB_IN_V_16 0x11
+#define ADC7_VDC_16 0x12
+#define ADC7_CC1_ID 0x13
+#define ADC7_VREF_BAT_THERM 0x15
+#define ADC7_IIN_FB 0x17
+
+/* 30k pull-up1 */
+#define ADC7_AMUX_THM1_30K_PU 0x24
+#define ADC7_AMUX_THM2_30K_PU 0x25
+#define ADC7_AMUX_THM3_30K_PU 0x26
+#define ADC7_AMUX_THM4_30K_PU 0x27
+#define ADC7_AMUX_THM5_30K_PU 0x28
+#define ADC7_AMUX_THM6_30K_PU 0x29
+#define ADC7_GPIO1_30K_PU 0x2a
+#define ADC7_GPIO2_30K_PU 0x2b
+#define ADC7_GPIO3_30K_PU 0x2c
+#define ADC7_GPIO4_30K_PU 0x2d
+#define ADC7_CC1_ID_30K_PU 0x33
+
+/* 100k pull-up2 */
+#define ADC7_AMUX_THM1_100K_PU 0x44
+#define ADC7_AMUX_THM2_100K_PU 0x45
+#define ADC7_AMUX_THM3_100K_PU 0x46
+#define ADC7_AMUX_THM4_100K_PU 0x47
+#define ADC7_AMUX_THM5_100K_PU 0x48
+#define ADC7_AMUX_THM6_100K_PU 0x49
+#define ADC7_GPIO1_100K_PU 0x4a
+#define ADC7_GPIO2_100K_PU 0x4b
+#define ADC7_GPIO3_100K_PU 0x4c
+#define ADC7_GPIO4_100K_PU 0x4d
+#define ADC7_CC1_ID_100K_PU 0x53
+
+/* 400k pull-up3 */
+#define ADC7_AMUX_THM1_400K_PU 0x64
+#define ADC7_AMUX_THM2_400K_PU 0x65
+#define ADC7_AMUX_THM3_400K_PU 0x66
+#define ADC7_AMUX_THM4_400K_PU 0x67
+#define ADC7_AMUX_THM5_400K_PU 0x68
+#define ADC7_AMUX_THM6_400K_PU 0x69
+#define ADC7_GPIO1_400K_PU 0x6a
+#define ADC7_GPIO2_400K_PU 0x6b
+#define ADC7_GPIO3_400K_PU 0x6c
+#define ADC7_GPIO4_400K_PU 0x6d
+#define ADC7_CC1_ID_400K_PU 0x73
+
+/* 1/3 Divider */
+#define ADC7_GPIO1_DIV3 0x8a
+#define ADC7_GPIO2_DIV3 0x8b
+#define ADC7_GPIO3_DIV3 0x8c
+#define ADC7_GPIO4_DIV3 0x8d
+
+#define ADC7_VPH_PWR 0x8e
+#define ADC7_VBAT_SNS 0x8f
+
+#define ADC7_SBUx 0x94
+#define ADC7_VBAT_2S_MID 0x96
+
#endif /* _DT_BINDINGS_QCOM_SPMI_VADC_H */
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Add documentation for PMIC7 ADC peripheral. For PMIC7 ADC, all SW
communication to ADC goes through PMK8350, which communicates with
other PMICs through PBS.
Signed-off-by: Jishnu Prakash <[email protected]>
---
.../bindings/iio/adc/qcom,spmi-vadc.yaml | 28 ++++++++++++++++------
1 file changed, 21 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
index 72db14c..20f010c 100644
--- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
@@ -13,7 +13,7 @@ maintainers:
description: |
SPMI PMIC voltage ADC (VADC) provides interface to clients to read
voltage. The VADC is a 15-bit sigma-delta ADC.
- SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
+ SPMI PMIC5/PMIC7 voltage ADC (ADC) provides interface to clients to read
voltage. The VADC is a 16-bit sigma-delta ADC.
properties:
@@ -23,6 +23,7 @@ properties:
- qcom,spmi-adc5
- qcom,spmi-adc-rev2
- qcom,pms405-adc
+ - qcom,spmi-adc7
reg:
description: VADC base address in the SPMI PMIC register map
@@ -65,6 +66,8 @@ patternProperties:
description: |
ADC channel number.
See include/dt-bindings/iio/qcom,spmi-vadc.h
+ For PMIC7 ADC, the channel numbers are specified separately per PMIC
+ in the PMIC-specific files in include/dt-bindings/iio/.
label:
description: |
@@ -72,7 +75,7 @@ patternProperties:
For thermistor inputs connected to generic AMUX or GPIO inputs
these can vary across platform for the same pins. Hence select
the platform schematics name for this channel. It is required
- for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2".
+ for "qcom,spmi-adc5", "qcom,spmi-adc7" and "qcom,spmi-adc-rev2".
allOf:
- $ref: /schemas/types.yaml#/definitions/string
@@ -85,6 +88,8 @@ patternProperties:
of 512 will be used.
- For compatible property "qcom,spmi-adc5", valid values are 250, 420
and 840. If property is not found, default value of 840 is used.
+ - For compatible property "qcom,spmi-adc7", valid values are 85, 340
+ and 1360. If property is not found, default value of 1360 is used.
- For compatible property "qcom,spmi-adc-rev2", valid values are 256,
512 and 1024. If property is not present, default value is 1024.
allOf:
@@ -109,11 +114,11 @@ patternProperties:
channel calibration. If property is not found, channel will be
calibrated with 0.625V and 1.25V reference channels, also
known as absolute calibration.
- - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
- if this property is specified VADC will use the VDD reference (1.875V)
- and GND for channel calibration. If property is not found, channel
- will be calibrated with 0V and 1.25V reference channels, also known
- as absolute calibration.
+ - For compatible property "qcom,spmi-adc5", "qcom,spmi-adc7" and
+ "qcom,spmi-adc-rev2", if this property is specified VADC will use
+ the VDD reference (1.875V) and GND for channel calibration. If
+ property is not found, channel will be calibrated with 0V and 1.25V
+ reference channels, also known as absolute calibration.
type: boolean
qcom,hw-settle-time:
@@ -135,6 +140,12 @@ patternProperties:
Certain controller digital versions have valid values of
15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms
If property is not found, channel will use 15us.
+ - For compatible property "qcom,spmi-adc7", delay = 15us for
+ value 0, 100us * (value) for values < 8, 1ms for value 8
+ and 2ms * (value - 8) otherwise.
+ Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 1000, 2000,
+ 4000, 8000, 16000, 32000, 64000, 128000 us.
+ If property is not found, channel will use 15us.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
@@ -147,6 +158,9 @@ patternProperties:
- For compatible property "qcom,spmi-vadc", valid values
are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
If property is not found, 1 sample will be used.
+ - For compatible property "qcom,spmi-adc5", "qcom,spmi-adc7"
+ and "qcom,spmi-adc-rev2", valid values are: 1, 2, 4, 8, 16.
+ If property is not found, 1 sample will be used.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
On Tue, Mar 24, 2020 at 5:46 PM Jishnu Prakash <[email protected]> wrote:
>
> The ADC architecture on PMIC7 is changed as compared to PMIC5. The
> major change from PMIC5 is that all SW communication to ADC goes through
> PMK8350, which communicates with other PMICs through PBS when the ADC
> on PMK8350 works in master mode. The SID register is used to identify the
> PMICs with which the PBS needs to communicate. Add support for the same.
>
> In addition, add definitions for ADC channels and virtual channel
> definitions per PMIC, to be used by ADC clients for PMIC7.
...
> +#define ADC_CHANNEL_OFFSET 0x8
> +#define ADC_CHANNEL_MASK 0xff
GENMASK()
...
> +#define ADC_APP_SID 0x40
> +#define ADC_APP_SID_MASK 0xf
GENMASK()
> +#define ADC7_CONV_TIMEOUT msecs_to_jiffies(10)
Useless.
...
> + buf[1] &= (u8) ~ADC5_USR_FAST_AVG_CTL_SAMPLES_MASK;
Use '0xFF ^ _MASK' instead of casting.
...
> + buf[3] &= (u8) ~ADC5_USR_HW_SETTLE_DELAY_MASK;
Ditto.
...
> + ret = adc5_write(adc, ADC5_USR_CONV_REQ, &conv_req, 1);
> +
> + return ret;
return adc5_write(...);
...
> + pr_err("ADC configure failed with %d\n", ret);
Use dev_*() instead everywhere.
...
> + /* No support for polling mode at present*/
> + wait_for_completion_timeout(&adc->complete,
> + ADC7_CONV_TIMEOUT);
One line. The limit is 80 and it can be bend in some cases a little bit.
...
> + v_channel = ((adc->chan_props[i].sid << ADC_CHANNEL_OFFSET) |
> + adc->chan_props[i].channel);
Too many parentheses.
...
> + sid = (chan >> ADC_CHANNEL_OFFSET);
> + chan = (chan & ADC_CHANNEL_MASK);
Ditto.
...
> + (adc->is_pmic7))
Ditto.
...
> + if (of_device_is_compatible(node, "qcom,spmi-adc7")) {
> + indio_dev->info = &adc7_info;
> + adc->is_pmic7 = true;
> + } else {
> + indio_dev->info = &adc5_info;
> + }
Hmm... I would rather put this as driver_data in ID structure(s).
...
> +static int adc5_exit(struct platform_device *pdev)
> +{
> + struct adc5_chip *adc = platform_get_drvdata(pdev);
> +
> + mutex_destroy(&adc->lock);
Are you sure you will have no race conditions? Does this driver use IRQs?
> + return 0;
> +}
...
> + s64 resistance = 0;
= adc_code // or sign extended variant if needed.
> + /* (ADC code * R_PULLUP (100Kohm)) / (full_scale_code - ADC code)*/
> + resistance = (s64) adc_code * R_PU_100K;
> + resistance = div64_s64(resistance, (RATIO_MAX_ADC7 - adc_code));
resistance *= R_PU_100K;
resistance = div64_s64(resistance, RATIO_MAX_ADC7 - adc_code);
...
> + int voltage, vtemp0, temp, i = 0;
> + while (i < ARRAY_SIZE(adcmap7_die_temp)) {
> + if (adcmap7_die_temp[i].x > voltage)
> + break;
> + i++;
> + }
for loop (one line less, more explicit initial value assignment)?
--
With Best Regards,
Andy Shevchenko
On Tue, 24 Mar 2020 21:14:08 +0530
Jishnu Prakash <[email protected]> wrote:
> Convert the adc bindings from .txt to .yaml format.
>
> Signed-off-by: Jishnu Prakash <[email protected]>
Hi Jishnu,
Looks to me like we can tighten the checks a fair bit in here rather
than just using uint32s
Now, my yaml isn't great so I won't try to say how, but there are plenty
of examples in tree.
Thanks,
Jonathan
> ---
> .../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 173 --------------------
> .../bindings/iio/adc/qcom,spmi-vadc.yaml | 178 +++++++++++++++++++++
> 2 files changed, 178 insertions(+), 173 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> deleted file mode 100644
> index c878768..0000000
> --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> +++ /dev/null
> @@ -1,173 +0,0 @@
> -Qualcomm's SPMI PMIC ADC
> -
> -- SPMI PMIC voltage ADC (VADC) provides interface to clients to read
> - voltage. The VADC is a 15-bit sigma-delta ADC.
> -- SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
> - voltage. The VADC is a 16-bit sigma-delta ADC.
> -
> -VADC node:
> -
> -- compatible:
> - Usage: required
> - Value type: <string>
> - Definition: Should contain "qcom,spmi-vadc".
> - Should contain "qcom,spmi-adc5" for PMIC5 ADC driver.
> - Should contain "qcom,spmi-adc-rev2" for PMIC rev2 ADC driver.
> - Should contain "qcom,pms405-adc" for PMS405 PMIC
> -
> -- reg:
> - Usage: required
> - Value type: <prop-encoded-array>
> - Definition: VADC base address in the SPMI PMIC register map.
> -
> -- #address-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: Must be one. Child node 'reg' property should define ADC
> - channel number.
> -
> -- #size-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: Must be zero.
> -
> -- #io-channel-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: Must be one. For details about IIO bindings see:
> - Documentation/devicetree/bindings/iio/iio-bindings.txt
> -
> -- interrupts:
> - Usage: optional
> - Value type: <prop-encoded-array>
> - Definition: End of conversion interrupt.
> -
> -Channel node properties:
> -
> -- reg:
> - Usage: required
> - Value type: <u32>
> - Definition: ADC channel number.
> - See include/dt-bindings/iio/qcom,spmi-vadc.h
> -
> -- label:
> - Usage: required for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2"
> - Value type: <empty>
> - Definition: ADC input of the platform as seen in the schematics.
> - For thermistor inputs connected to generic AMUX or GPIO inputs
> - these can vary across platform for the same pins. Hence select
> - the platform schematics name for this channel.
> -
> -- qcom,decimation:
> - Usage: optional
> - Value type: <u32>
> - Definition: This parameter is used to decrease ADC sampling rate.
> - Quicker measurements can be made by reducing decimation ratio.
> - - For compatible property "qcom,spmi-vadc", valid values are
> - 512, 1024, 2048, 4096. If property is not found, default value
> - of 512 will be used.
> - - For compatible property "qcom,spmi-adc5", valid values are 250, 420
> - and 840. If property is not found, default value of 840 is used.
> - - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
> - 512 and 1024. If property is not present, default value is 1024.
> -
> -- qcom,pre-scaling:
> - Usage: optional
> - Value type: <u32 array>
> - Definition: Used for scaling the channel input signal before the signal is
> - fed to VADC. The configuration for this node is to know the
> - pre-determined ratio and use it for post scaling. Select one from
> - the following options.
> - <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
> - If property is not found default value depending on chip will be used.
> -
> -- qcom,ratiometric:
> - Usage: optional
> - Value type: <empty>
> - Definition: Channel calibration type.
> - - For compatible property "qcom,spmi-vadc", if this property is
> - specified VADC will use the VDD reference (1.8V) and GND for
> - channel calibration. If property is not found, channel will be
> - calibrated with 0.625V and 1.25V reference channels, also
> - known as absolute calibration.
> - - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
> - if this property is specified VADC will use the VDD reference
> - (1.875V) and GND for channel calibration. If property is not found,
> - channel will be calibrated with 0V and 1.25V reference channels,
> - also known as absolute calibration.
> -
> -- qcom,hw-settle-time:
> - Usage: optional
> - Value type: <u32>
> - Definition: Time between AMUX getting configured and the ADC starting
> - conversion. The 'hw_settle_time' is an index used from valid values
> - and programmed in hardware to achieve the hardware settling delay.
> - - For compatible property "qcom,spmi-vadc" and "qcom,spmi-adc-rev2",
> - Delay = 100us * (hw_settle_time) for hw_settle_time < 11,
> - and 2ms * (hw_settle_time - 10) otherwise.
> - Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800,
> - 900 us and 1, 2, 4, 6, 8, 10 ms.
> - If property is not found, channel will use 0us.
> - - For compatible property "qcom,spmi-adc5", delay = 15us for
> - value 0, 100us * (value) for values < 11,
> - and 2ms * (value - 10) otherwise.
> - Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 800,
> - 900 us and 1, 2, 4, 6, 8, 10 ms
> - Certain controller digital versions have valid values of
> - 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms
> - If property is not found, channel will use 15us.
> -
> -- qcom,avg-samples:
> - Usage: optional
> - Value type: <u32>
> - Definition: Number of samples to be used for measurement.
> - Averaging provides the option to obtain a single measurement
> - from the ADC that is an average of multiple samples. The value
> - selected is 2^(value).
> - - For compatible property "qcom,spmi-vadc", valid values
> - are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
> - If property is not found, 1 sample will be used.
> - - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
> - valid values are: 1, 2, 4, 8, 16
> - If property is not found, 1 sample will be used.
> -
> -NOTE:
> -
> -For compatible property "qcom,spmi-vadc" following channels, also known as
> -reference point channels, are used for result calibration and their channel
> -configuration nodes should be defined:
> -VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV,
> -VADC_GND_REF and VADC_VDD_VADC.
> -
> -Example:
> -
> -#include <dt-bindings/iio/qcom,spmi-vadc.h>
> -#include <linux/irq.h>
> -/* ... */
> -
> - /* VADC node */
> - pmic_vadc: vadc@3100 {
> - compatible = "qcom,spmi-vadc";
> - reg = <0x3100>;
> - interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - #io-channel-cells = <1>;
> - io-channel-ranges;
> -
> - /* Channel node */
> - adc-chan@VADC_LR_MUX10_USB_ID {
> - reg = <VADC_LR_MUX10_USB_ID>;
> - qcom,decimation = <512>;
> - qcom,ratiometric;
> - qcom,hw-settle-time = <200>;
> - qcom,avg-samples = <1>;
> - qcom,pre-scaling = <1 3>;
> - };
> - };
> -
> - /* IIO client node */
> - usb {
> - io-channels = <&pmic_vadc VADC_LR_MUX10_USB_ID>;
> - io-channel-names = "vadc";
> - };
> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> new file mode 100644
> index 0000000..72db14c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> @@ -0,0 +1,178 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/adc/qcom,spmi-vadc.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm's SPMI PMIC ADC
> +
> +maintainers:
> + - Andy Gross <[email protected]>
> + - Bjorn Andersson <[email protected]>
> +
> +description: |
> + SPMI PMIC voltage ADC (VADC) provides interface to clients to read
> + voltage. The VADC is a 15-bit sigma-delta ADC.
> + SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
> + voltage. The VADC is a 16-bit sigma-delta ADC.
> +
> +properties:
> + compatible:
> + enum:
> + - qcom,spmi-vadc
> + - qcom,spmi-adc5
> + - qcom,spmi-adc-rev2
> + - qcom,pms405-adc
> +
> + reg:
> + description: VADC base address in the SPMI PMIC register map
> + maxItems: 1
> +
> + '#address-cells':
> + const: 1
> +
> + '#size-cells':
> + const: 0
> +
> + '#io-channel-cells':
> + const: 1
> +
> + interrupts:
> + maxItems: 1
> + description:
> + End of conversion interrupt.
> +
> +required:
> + - compatible
> + - reg
> + - '#address-cells'
> + - '#size-cells'
> + - '#io-channel-cells'
> +
> +patternProperties:
> + "^[a-z0-9-_@]$":
> + type: object
> + description: |
> + Represents the external channels which are connected to the ADC.
> + For compatible property "qcom,spmi-vadc" following channels, also known as
> + reference point channels, are used for result calibration and their channel
> + configuration nodes should be defined:
> + VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV,
> + VADC_GND_REF and VADC_VDD_VADC.
> +
> + properties:
> + reg:
> + description: |
> + ADC channel number.
> + See include/dt-bindings/iio/qcom,spmi-vadc.h
> +
> + label:
> + description: |
> + ADC input of the platform as seen in the schematics.
> + For thermistor inputs connected to generic AMUX or GPIO inputs
> + these can vary across platform for the same pins. Hence select
> + the platform schematics name for this channel. It is required
> + for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2".
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/string
> +
> + qcom,decimation:
> + description: |
> + This parameter is used to decrease ADC sampling rate.
> + Quicker measurements can be made by reducing decimation ratio.
> + - For compatible property "qcom,spmi-vadc", valid values are
> + 512, 1024, 2048, 4096. If property is not found, default value
> + of 512 will be used.
> + - For compatible property "qcom,spmi-adc5", valid values are 250, 420
> + and 840. If property is not found, default value of 840 is used.
> + - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
> + 512 and 1024. If property is not present, default value is 1024.
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
Should ideally verify all the values against models etc rather than a uint32 binding.
> +
> + qcom,pre-scaling:
> + description: |
> + Used for scaling the channel input signal before the signal is
> + fed to VADC. The configuration for this node is to know the
> + pre-determined ratio and use it for post scaling. Select one from
> + the following options.
> + <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
Can we not provide this list as something that can be verified?
> + If property is not found default value depending on chip will be used.
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
> +
> + qcom,ratiometric:
> + description: |
> + Channel calibration type.
> + - For compatible property "qcom,spmi-vadc", if this property is
> + specified VADC will use the VDD reference (1.8V) and GND for
> + channel calibration. If property is not found, channel will be
> + calibrated with 0.625V and 1.25V reference channels, also
> + known as absolute calibration.
> + - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
> + if this property is specified VADC will use the VDD reference (1.875V)
> + and GND for channel calibration. If property is not found, channel
> + will be calibrated with 0V and 1.25V reference channels, also known
> + as absolute calibration.
> + type: boolean
> +
> + qcom,hw-settle-time:
> + description: |
> + Time between AMUX getting configured and the ADC starting
> + conversion. The 'hw_settle_time' is an index used from valid values
> + and programmed in hardware to achieve the hardware settling delay.
> + - For compatible property "qcom,spmi-vadc" and "qcom,spmi-adc-rev2",
> + Delay = 100us * (hw_settle_time) for hw_settle_time < 11,
> + and 2ms * (hw_settle_time - 10) otherwise.
> + Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800,
> + 900 us and 1, 2, 4, 6, 8, 10 ms.
> + If property is not found, channel will use 0us.
> + - For compatible property "qcom,spmi-adc5", delay = 15us for
> + value 0, 100us * (value) for values < 11,
> + and 2ms * (value - 10) otherwise.
> + Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 800,
> + 900 us and 1, 2, 4, 6, 8, 10 ms
> + Certain controller digital versions have valid values of
> + 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms
> + If property is not found, channel will use 15us.
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
Can we verify those values.
> +
> + qcom,avg-samples:
> + description: |
> + Number of samples to be used for measurement.
> + Averaging provides the option to obtain a single measurement
> + from the ADC that is an average of multiple samples. The value
> + selected is 2^(value).
> + - For compatible property "qcom,spmi-vadc", valid values
> + are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
> + If property is not found, 1 sample will be used.
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
Verify the values if possible.
> +
> + required:
> + - reg
> + - diff-channels
> +
> +examples:
> + - |
> + /* VADC node */
> + pmic_vadc: vadc@3100 {
Should really be using generic names, so adc@3100 preferred.
> + compatible = "qcom,spmi-vadc";
> + reg = <0x3100>;
> + interrupts = <0x0 0x31 0x0 0x1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #io-channel-cells = <1>;
> + io-channel-ranges;
> +
> + /* Channel node */
> + adc-chan@0x39 {
> + reg = <0x39>;
> + qcom,decimation = <512>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,avg-samples = <1>;
> + qcom,pre-scaling = <1 3>;
> + };
> + };
On Tue, 24 Mar 2020 21:14:09 +0530
Jishnu Prakash <[email protected]> wrote:
> Add documentation for PMIC7 ADC peripheral. For PMIC7 ADC, all SW
> communication to ADC goes through PMK8350, which communicates with
> other PMICs through PBS.
>
> Signed-off-by: Jishnu Prakash <[email protected]>
> ---
> .../bindings/iio/adc/qcom,spmi-vadc.yaml | 28 ++++++++++++++++------
> 1 file changed, 21 insertions(+), 7 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> index 72db14c..20f010c 100644
> --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> @@ -13,7 +13,7 @@ maintainers:
> description: |
> SPMI PMIC voltage ADC (VADC) provides interface to clients to read
> voltage. The VADC is a 15-bit sigma-delta ADC.
> - SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
> + SPMI PMIC5/PMIC7 voltage ADC (ADC) provides interface to clients to read
> voltage. The VADC is a 16-bit sigma-delta ADC.
>
> properties:
> @@ -23,6 +23,7 @@ properties:
> - qcom,spmi-adc5
> - qcom,spmi-adc-rev2
> - qcom,pms405-adc
> + - qcom,spmi-adc7
>
> reg:
> description: VADC base address in the SPMI PMIC register map
> @@ -65,6 +66,8 @@ patternProperties:
> description: |
> ADC channel number.
> See include/dt-bindings/iio/qcom,spmi-vadc.h
> + For PMIC7 ADC, the channel numbers are specified separately per PMIC
> + in the PMIC-specific files in include/dt-bindings/iio/.
That makes me thing we really should have separate compatibles. The
parts clearly have differences, even if we haven't needed to use them
explicitly as yet.
>
> label:
> description: |
> @@ -72,7 +75,7 @@ patternProperties:
> For thermistor inputs connected to generic AMUX or GPIO inputs
> these can vary across platform for the same pins. Hence select
> the platform schematics name for this channel. It is required
> - for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2".
> + for "qcom,spmi-adc5", "qcom,spmi-adc7" and "qcom,spmi-adc-rev2".
> allOf:
> - $ref: /schemas/types.yaml#/definitions/string
>
> @@ -85,6 +88,8 @@ patternProperties:
> of 512 will be used.
> - For compatible property "qcom,spmi-adc5", valid values are 250, 420
> and 840. If property is not found, default value of 840 is used.
> + - For compatible property "qcom,spmi-adc7", valid values are 85, 340
> + and 1360. If property is not found, default value of 1360 is used.
> - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
> 512 and 1024. If property is not present, default value is 1024.
> allOf:
> @@ -109,11 +114,11 @@ patternProperties:
> channel calibration. If property is not found, channel will be
> calibrated with 0.625V and 1.25V reference channels, also
> known as absolute calibration.
> - - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
> - if this property is specified VADC will use the VDD reference (1.875V)
> - and GND for channel calibration. If property is not found, channel
> - will be calibrated with 0V and 1.25V reference channels, also known
> - as absolute calibration.
> + - For compatible property "qcom,spmi-adc5", "qcom,spmi-adc7" and
> + "qcom,spmi-adc-rev2", if this property is specified VADC will use
> + the VDD reference (1.875V) and GND for channel calibration. If
> + property is not found, channel will be calibrated with 0V and 1.25V
> + reference channels, also known as absolute calibration.
> type: boolean
>
> qcom,hw-settle-time:
> @@ -135,6 +140,12 @@ patternProperties:
> Certain controller digital versions have valid values of
> 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms
> If property is not found, channel will use 15us.
> + - For compatible property "qcom,spmi-adc7", delay = 15us for
> + value 0, 100us * (value) for values < 8, 1ms for value 8
> + and 2ms * (value - 8) otherwise.
> + Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 1000, 2000,
> + 4000, 8000, 16000, 32000, 64000, 128000 us.
> + If property is not found, channel will use 15us.
> allOf:
> - $ref: /schemas/types.yaml#/definitions/uint32
>
> @@ -147,6 +158,9 @@ patternProperties:
> - For compatible property "qcom,spmi-vadc", valid values
> are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
> If property is not found, 1 sample will be used.
> + - For compatible property "qcom,spmi-adc5", "qcom,spmi-adc7"
> + and "qcom,spmi-adc-rev2", valid values are: 1, 2, 4, 8, 16.
> + If property is not found, 1 sample will be used.
> allOf:
> - $ref: /schemas/types.yaml#/definitions/uint32
>
On Tue, 24 Mar 2020 21:14:10 +0530
Jishnu Prakash <[email protected]> wrote:
> The ADC architecture on PMIC7 is changed as compared to PMIC5. The
> major change from PMIC5 is that all SW communication to ADC goes through
> PMK8350, which communicates with other PMICs through PBS when the ADC
> on PMK8350 works in master mode. The SID register is used to identify the
> PMICs with which the PBS needs to communicate. Add support for the same.
>
> In addition, add definitions for ADC channels and virtual channel
> definitions per PMIC, to be used by ADC clients for PMIC7.
>
> Signed-off-by: Jishnu Prakash <[email protected]>
A few additions from me.
> ---
...
>
> +static int adc5_exit(struct platform_device *pdev)
> +{
> + struct adc5_chip *adc = platform_get_drvdata(pdev);
> +
> + mutex_destroy(&adc->lock);
Andy raised potential races. You definitely have some as this
will destroy the mutex before you've removed the userspace interfaces.
> + return 0;
> +}
> +
> static struct platform_driver adc5_driver = {
> .driver = {
> .name = "qcom-spmi-adc5.c",
> .of_match_table = adc5_match_table,
> },
> .probe = adc5_probe,
> + .remove = adc5_exit,
> };
> module_platform_driver(adc5_driver);
>
...
>
> +static int qcom_vadc7_scale_hw_calib_die_temp(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc5_data *data,
> + u16 adc_code, int *result_mdec)
> +{
> +
> + int voltage, vtemp0, temp, i = 0;
> +
> + voltage = qcom_vadc_scale_code_voltage_factor(adc_code,
> + prescale, data, 1);
> +
> + while (i < ARRAY_SIZE(adcmap7_die_temp)) {
> + if (adcmap7_die_temp[i].x > voltage)
> + break;
> + i++;
> + }
For loop (I think Andy also raised this one).
> +
> + if (i == 0) {
> + *result_mdec = DIE_TEMP_ADC7_SCALE_1;
> + } else if (i == ARRAY_SIZE(adcmap7_die_temp)) {
> + *result_mdec = DIE_TEMP_ADC7_MAX;
> + } else {
> + vtemp0 = adcmap7_die_temp[i-1].x;
Spaces around the -
Same elsewhere.
> + voltage = voltage - vtemp0;
> + temp = div64_s64(voltage * DIE_TEMP_ADC7_SCALE_FACTOR,
> + adcmap7_die_temp[i-1].y);
> + temp += DIE_TEMP_ADC7_SCALE_1 + (DIE_TEMP_ADC7_SCALE_2 * (i-1));
> + *result_mdec = temp;
> + }
> +
> + return 0;
> +}
> +
> static int qcom_vadc_scale_hw_smb_temp(
> const struct vadc_prescale_ratio *prescale,
> const struct adc5_data *data,
...
On Tue, 24 Mar 2020 21:14:08 +0530, Jishnu Prakash wrote:
> Convert the adc bindings from .txt to .yaml format.
>
> Signed-off-by: Jishnu Prakash <[email protected]>
> ---
> .../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 173 --------------------
> .../bindings/iio/adc/qcom,spmi-vadc.yaml | 178 +++++++++++++++++++++
> 2 files changed, 178 insertions(+), 173 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dts:20.11-26: Warning (reg_format): /example-0/vadc@3100:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dt.yaml: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dt.yaml: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dt.yaml: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dt.yaml: vadc@3100: 'adc-chan@0x39' does not match any of the regexes: '.*-names$', '.*-supply$', '^#.*-cells$', '^#[a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$', '^__.*__$', 'pinctrl-[0-9]+'
See https://patchwork.ozlabs.org/patch/1260800
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
On Tue, Mar 24, 2020 at 09:14:10PM +0530, Jishnu Prakash wrote:
> The ADC architecture on PMIC7 is changed as compared to PMIC5. The
> major change from PMIC5 is that all SW communication to ADC goes through
> PMK8350, which communicates with other PMICs through PBS when the ADC
> on PMK8350 works in master mode. The SID register is used to identify the
> PMICs with which the PBS needs to communicate. Add support for the same.
>
> In addition, add definitions for ADC channels and virtual channel
> definitions per PMIC, to be used by ADC clients for PMIC7.
>
> Signed-off-by: Jishnu Prakash <[email protected]>
> ---
> drivers/iio/adc/qcom-spmi-adc5.c | 239 ++++++++++++++++++++-
> drivers/iio/adc/qcom-vadc-common.c | 260 +++++++++++++++++++++++
> drivers/iio/adc/qcom-vadc-common.h | 14 ++
> include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h | 67 ++++++
> include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h | 88 ++++++++
> include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h | 46 ++++
> include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h | 28 +++
> include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h | 28 +++
> include/dt-bindings/iio/qcom,spmi-vadc.h | 78 ++++++-
DT headers go in the binding patch(es).
> 9 files changed, 843 insertions(+), 5 deletions(-)
> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h
> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h
> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h
> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h
> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h
Hi Jishnu,
On Tue, Mar 24, 2020 at 9:15 PM Jishnu Prakash <[email protected]> wrote:
>
> Add documentation for PMIC7 ADC peripheral. For PMIC7 ADC, all SW
> communication to ADC goes through PMK8350, which communicates with
> other PMICs through PBS.
What is PMK8350? What is PBS? Please expand the acronyms and describe
more verbosely.
>
> Signed-off-by: Jishnu Prakash <[email protected]>
> ---
> .../bindings/iio/adc/qcom,spmi-vadc.yaml | 28 ++++++++++++++++------
> 1 file changed, 21 insertions(+), 7 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> index 72db14c..20f010c 100644
> --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> @@ -13,7 +13,7 @@ maintainers:
> description: |
> SPMI PMIC voltage ADC (VADC) provides interface to clients to read
> voltage. The VADC is a 15-bit sigma-delta ADC.
> - SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
> + SPMI PMIC5/PMIC7 voltage ADC (ADC) provides interface to clients to read
> voltage. The VADC is a 16-bit sigma-delta ADC.
>
> properties:
> @@ -23,6 +23,7 @@ properties:
> - qcom,spmi-adc5
> - qcom,spmi-adc-rev2
> - qcom,pms405-adc
> + - qcom,spmi-adc7
>
> reg:
> description: VADC base address in the SPMI PMIC register map
> @@ -65,6 +66,8 @@ patternProperties:
> description: |
> ADC channel number.
> See include/dt-bindings/iio/qcom,spmi-vadc.h
> + For PMIC7 ADC, the channel numbers are specified separately per PMIC
> + in the PMIC-specific files in include/dt-bindings/iio/.
>
> label:
> description: |
> @@ -72,7 +75,7 @@ patternProperties:
> For thermistor inputs connected to generic AMUX or GPIO inputs
> these can vary across platform for the same pins. Hence select
> the platform schematics name for this channel. It is required
> - for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2".
> + for "qcom,spmi-adc5", "qcom,spmi-adc7" and "qcom,spmi-adc-rev2".
> allOf:
> - $ref: /schemas/types.yaml#/definitions/string
>
> @@ -85,6 +88,8 @@ patternProperties:
> of 512 will be used.
> - For compatible property "qcom,spmi-adc5", valid values are 250, 420
> and 840. If property is not found, default value of 840 is used.
> + - For compatible property "qcom,spmi-adc7", valid values are 85, 340
> + and 1360. If property is not found, default value of 1360 is used.
> - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
> 512 and 1024. If property is not present, default value is 1024.
> allOf:
> @@ -109,11 +114,11 @@ patternProperties:
> channel calibration. If property is not found, channel will be
> calibrated with 0.625V and 1.25V reference channels, also
> known as absolute calibration.
> - - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
> - if this property is specified VADC will use the VDD reference (1.875V)
> - and GND for channel calibration. If property is not found, channel
> - will be calibrated with 0V and 1.25V reference channels, also known
> - as absolute calibration.
> + - For compatible property "qcom,spmi-adc5", "qcom,spmi-adc7" and
> + "qcom,spmi-adc-rev2", if this property is specified VADC will use
> + the VDD reference (1.875V) and GND for channel calibration. If
> + property is not found, channel will be calibrated with 0V and 1.25V
> + reference channels, also known as absolute calibration.
> type: boolean
>
> qcom,hw-settle-time:
> @@ -135,6 +140,12 @@ patternProperties:
> Certain controller digital versions have valid values of
> 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms
> If property is not found, channel will use 15us.
> + - For compatible property "qcom,spmi-adc7", delay = 15us for
> + value 0, 100us * (value) for values < 8, 1ms for value 8
> + and 2ms * (value - 8) otherwise.
> + Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 1000, 2000,
> + 4000, 8000, 16000, 32000, 64000, 128000 us.
> + If property is not found, channel will use 15us.
> allOf:
> - $ref: /schemas/types.yaml#/definitions/uint32
>
> @@ -147,6 +158,9 @@ patternProperties:
> - For compatible property "qcom,spmi-vadc", valid values
> are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
> If property is not found, 1 sample will be used.
> + - For compatible property "qcom,spmi-adc5", "qcom,spmi-adc7"
> + and "qcom,spmi-adc-rev2", valid values are: 1, 2, 4, 8, 16.
> + If property is not found, 1 sample will be used.
> allOf:
> - $ref: /schemas/types.yaml#/definitions/uint32
>
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
On Tue, Mar 24, 2020 at 9:15 PM Jishnu Prakash <[email protected]> wrote:
>
> Convert the adc bindings from .txt to .yaml format.
>
> Signed-off-by: Jishnu Prakash <[email protected]>
> ---
> .../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 173 --------------------
> .../bindings/iio/adc/qcom,spmi-vadc.yaml | 178 +++++++++++++++++++++
> 2 files changed, 178 insertions(+), 173 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> deleted file mode 100644
> index c878768..0000000
> --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> +++ /dev/null
> @@ -1,173 +0,0 @@
> -Qualcomm's SPMI PMIC ADC
> -
> -- SPMI PMIC voltage ADC (VADC) provides interface to clients to read
> - voltage. The VADC is a 15-bit sigma-delta ADC.
> -- SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
> - voltage. The VADC is a 16-bit sigma-delta ADC.
> -
> -VADC node:
> -
> -- compatible:
> - Usage: required
> - Value type: <string>
> - Definition: Should contain "qcom,spmi-vadc".
> - Should contain "qcom,spmi-adc5" for PMIC5 ADC driver.
> - Should contain "qcom,spmi-adc-rev2" for PMIC rev2 ADC driver.
> - Should contain "qcom,pms405-adc" for PMS405 PMIC
> -
> -- reg:
> - Usage: required
> - Value type: <prop-encoded-array>
> - Definition: VADC base address in the SPMI PMIC register map.
> -
> -- #address-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: Must be one. Child node 'reg' property should define ADC
> - channel number.
> -
> -- #size-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: Must be zero.
> -
> -- #io-channel-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: Must be one. For details about IIO bindings see:
> - Documentation/devicetree/bindings/iio/iio-bindings.txt
> -
> -- interrupts:
> - Usage: optional
> - Value type: <prop-encoded-array>
> - Definition: End of conversion interrupt.
> -
> -Channel node properties:
> -
> -- reg:
> - Usage: required
> - Value type: <u32>
> - Definition: ADC channel number.
> - See include/dt-bindings/iio/qcom,spmi-vadc.h
> -
> -- label:
> - Usage: required for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2"
> - Value type: <empty>
> - Definition: ADC input of the platform as seen in the schematics.
> - For thermistor inputs connected to generic AMUX or GPIO inputs
> - these can vary across platform for the same pins. Hence select
> - the platform schematics name for this channel.
> -
> -- qcom,decimation:
> - Usage: optional
> - Value type: <u32>
> - Definition: This parameter is used to decrease ADC sampling rate.
> - Quicker measurements can be made by reducing decimation ratio.
> - - For compatible property "qcom,spmi-vadc", valid values are
> - 512, 1024, 2048, 4096. If property is not found, default value
> - of 512 will be used.
> - - For compatible property "qcom,spmi-adc5", valid values are 250, 420
> - and 840. If property is not found, default value of 840 is used.
> - - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
> - 512 and 1024. If property is not present, default value is 1024.
> -
> -- qcom,pre-scaling:
> - Usage: optional
> - Value type: <u32 array>
> - Definition: Used for scaling the channel input signal before the signal is
> - fed to VADC. The configuration for this node is to know the
> - pre-determined ratio and use it for post scaling. Select one from
> - the following options.
> - <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
> - If property is not found default value depending on chip will be used.
> -
> -- qcom,ratiometric:
> - Usage: optional
> - Value type: <empty>
> - Definition: Channel calibration type.
> - - For compatible property "qcom,spmi-vadc", if this property is
> - specified VADC will use the VDD reference (1.8V) and GND for
> - channel calibration. If property is not found, channel will be
> - calibrated with 0.625V and 1.25V reference channels, also
> - known as absolute calibration.
> - - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
> - if this property is specified VADC will use the VDD reference
> - (1.875V) and GND for channel calibration. If property is not found,
> - channel will be calibrated with 0V and 1.25V reference channels,
> - also known as absolute calibration.
> -
> -- qcom,hw-settle-time:
> - Usage: optional
> - Value type: <u32>
> - Definition: Time between AMUX getting configured and the ADC starting
> - conversion. The 'hw_settle_time' is an index used from valid values
> - and programmed in hardware to achieve the hardware settling delay.
> - - For compatible property "qcom,spmi-vadc" and "qcom,spmi-adc-rev2",
> - Delay = 100us * (hw_settle_time) for hw_settle_time < 11,
> - and 2ms * (hw_settle_time - 10) otherwise.
> - Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800,
> - 900 us and 1, 2, 4, 6, 8, 10 ms.
> - If property is not found, channel will use 0us.
> - - For compatible property "qcom,spmi-adc5", delay = 15us for
> - value 0, 100us * (value) for values < 11,
> - and 2ms * (value - 10) otherwise.
> - Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 800,
> - 900 us and 1, 2, 4, 6, 8, 10 ms
> - Certain controller digital versions have valid values of
> - 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms
> - If property is not found, channel will use 15us.
> -
> -- qcom,avg-samples:
> - Usage: optional
> - Value type: <u32>
> - Definition: Number of samples to be used for measurement.
> - Averaging provides the option to obtain a single measurement
> - from the ADC that is an average of multiple samples. The value
> - selected is 2^(value).
> - - For compatible property "qcom,spmi-vadc", valid values
> - are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
> - If property is not found, 1 sample will be used.
> - - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
> - valid values are: 1, 2, 4, 8, 16
> - If property is not found, 1 sample will be used.
> -
> -NOTE:
> -
> -For compatible property "qcom,spmi-vadc" following channels, also known as
> -reference point channels, are used for result calibration and their channel
> -configuration nodes should be defined:
> -VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV,
> -VADC_GND_REF and VADC_VDD_VADC.
> -
> -Example:
> -
> -#include <dt-bindings/iio/qcom,spmi-vadc.h>
> -#include <linux/irq.h>
> -/* ... */
> -
> - /* VADC node */
> - pmic_vadc: vadc@3100 {
> - compatible = "qcom,spmi-vadc";
> - reg = <0x3100>;
> - interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - #io-channel-cells = <1>;
> - io-channel-ranges;
> -
> - /* Channel node */
> - adc-chan@VADC_LR_MUX10_USB_ID {
> - reg = <VADC_LR_MUX10_USB_ID>;
> - qcom,decimation = <512>;
> - qcom,ratiometric;
> - qcom,hw-settle-time = <200>;
> - qcom,avg-samples = <1>;
> - qcom,pre-scaling = <1 3>;
> - };
> - };
> -
> - /* IIO client node */
> - usb {
> - io-channels = <&pmic_vadc VADC_LR_MUX10_USB_ID>;
> - io-channel-names = "vadc";
> - };
> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> new file mode 100644
> index 0000000..72db14c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> @@ -0,0 +1,178 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/adc/qcom,spmi-vadc.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm's SPMI PMIC ADC
> +
> +maintainers:
> + - Andy Gross <[email protected]>
> + - Bjorn Andersson <[email protected]>
> +
> +description: |
> + SPMI PMIC voltage ADC (VADC) provides interface to clients to read
> + voltage. The VADC is a 15-bit sigma-delta ADC.
> + SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
> + voltage. The VADC is a 16-bit sigma-delta ADC.
> +
> +properties:
> + compatible:
> + enum:
> + - qcom,spmi-vadc
> + - qcom,spmi-adc5
> + - qcom,spmi-adc-rev2
> + - qcom,pms405-adc
> +
> + reg:
> + description: VADC base address in the SPMI PMIC register map
> + maxItems: 1
> +
> + '#address-cells':
> + const: 1
> +
> + '#size-cells':
> + const: 0
> +
> + '#io-channel-cells':
> + const: 1
> +
> + interrupts:
> + maxItems: 1
> + description:
> + End of conversion interrupt.
> +
> +required:
> + - compatible
> + - reg
> + - '#address-cells'
> + - '#size-cells'
> + - '#io-channel-cells'
> +
> +patternProperties:
> + "^[a-z0-9-_@]$":
> + type: object
> + description: |
> + Represents the external channels which are connected to the ADC.
> + For compatible property "qcom,spmi-vadc" following channels, also known as
> + reference point channels, are used for result calibration and their channel
> + configuration nodes should be defined:
> + VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV,
> + VADC_GND_REF and VADC_VDD_VADC.
Instead of this note for "qcom,spmi-vadc", you can enforce this
through checks in YAML grammar.
A simple example can be found in
Documentation/devicetree/bindings/thermal/qcom-tsens.yaml. Look for
the if, then, else clause which determines how many interrupts need to
be defined.
> +
> + properties:
> + reg:
> + description: |
> + ADC channel number.
> + See include/dt-bindings/iio/qcom,spmi-vadc.h
> +
> + label:
> + description: |
> + ADC input of the platform as seen in the schematics.
> + For thermistor inputs connected to generic AMUX or GPIO inputs
> + these can vary across platform for the same pins. Hence select
> + the platform schematics name for this channel. It is required
> + for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2".
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/string
You shouldn't need allOf here.
Just a "$ref: /schemas/types.yaml#/definitions/string" should be fine.
And move it above the description.
Same for all the uses of allOf below.
> + qcom,decimation:
> + description: |
> + This parameter is used to decrease ADC sampling rate.
> + Quicker measurements can be made by reducing decimation ratio.
> + - For compatible property "qcom,spmi-vadc", valid values are
> + 512, 1024, 2048, 4096. If property is not found, default value
> + of 512 will be used.
> + - For compatible property "qcom,spmi-adc5", valid values are 250, 420
> + and 840. If property is not found, default value of 840 is used.
> + - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
> + 512 and 1024. If property is not present, default value is 1024.
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
> +
As pointed out by Jonathon, please enforce these by keying off the
compatible property.
> + qcom,pre-scaling:
> + description: |
> + Used for scaling the channel input signal before the signal is
> + fed to VADC. The configuration for this node is to know the
> + pre-determined ratio and use it for post scaling. Select one from
> + the following options.
Please improve this description from the old binding. Does <1 3> mean
the signal is scaled 3x or 1/3x?
> + <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
> + If property is not found default value depending on chip will be used.
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
> +
> + qcom,ratiometric:
> + description: |
> + Channel calibration type.
> + - For compatible property "qcom,spmi-vadc", if this property is
> + specified VADC will use the VDD reference (1.8V) and GND for
> + channel calibration. If property is not found, channel will be
> + calibrated with 0.625V and 1.25V reference channels, also
> + known as absolute calibration.
> + - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2",
> + if this property is specified VADC will use the VDD reference (1.875V)
> + and GND for channel calibration. If property is not found, channel
> + will be calibrated with 0V and 1.25V reference channels, also known
> + as absolute calibration.
> + type: boolean
> +
please enforce these by keying off the compatible property.
> + qcom,hw-settle-time:
> + description: |
> + Time between AMUX getting configured and the ADC starting
> + conversion. The 'hw_settle_time' is an index used from valid values
> + and programmed in hardware to achieve the hardware settling delay.
> + - For compatible property "qcom,spmi-vadc" and "qcom,spmi-adc-rev2",
> + Delay = 100us * (hw_settle_time) for hw_settle_time < 11,
> + and 2ms * (hw_settle_time - 10) otherwise.
> + Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800,
> + 900 us and 1, 2, 4, 6, 8, 10 ms.
> + If property is not found, channel will use 0us.
> + - For compatible property "qcom,spmi-adc5", delay = 15us for
> + value 0, 100us * (value) for values < 11,
> + and 2ms * (value - 10) otherwise.
> + Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 800,
> + 900 us and 1, 2, 4, 6, 8, 10 ms
> + Certain controller digital versions have valid values of
> + 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms
> + If property is not found, channel will use 15us.
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
> +
please enforce these by keying off the compatible property.
> + qcom,avg-samples:
> + description: |
> + Number of samples to be used for measurement.
> + Averaging provides the option to obtain a single measurement
> + from the ADC that is an average of multiple samples. The value
> + selected is 2^(value).
> + - For compatible property "qcom,spmi-vadc", valid values
> + are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
> + If property is not found, 1 sample will be used.
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
> +
please enforce these by keying off the compatible property.
> + required:
> + - reg
> + - diff-channels
> +
> +examples:
> + - |
> + /* VADC node */
> + pmic_vadc: vadc@3100 {
> + compatible = "qcom,spmi-vadc";
> + reg = <0x3100>;
> + interrupts = <0x0 0x31 0x0 0x1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #io-channel-cells = <1>;
> + io-channel-ranges;
> +
> + /* Channel node */
> + adc-chan@0x39 {
> + reg = <0x39>;
> + qcom,decimation = <512>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,avg-samples = <1>;
> + qcom,pre-scaling = <1 3>;
> + };
> + };
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
Hi Jonathan,
On 3/28/2020 10:21 PM, Jonathan Cameron wrote:
> On Tue, 24 Mar 2020 21:14:08 +0530
> Jishnu Prakash <[email protected]> wrote:
>
>> Convert the adc bindings from .txt to .yaml format.
>>
>> Signed-off-by: Jishnu Prakash <[email protected]>
> Hi Jishnu,
>
> Looks to me like we can tighten the checks a fair bit in here rather
> than just using uint32s
>
> Now, my yaml isn't great so I won't try to say how, but there are plenty
> of examples in tree.
>
> Thanks,
>
> Jonathan
>
> +
> + qcom,decimation:
> + description: |
> + This parameter is used to decrease ADC sampling rate.
> + Quicker measurements can be made by reducing decimation ratio.
> + - For compatible property "qcom,spmi-vadc", valid values are
> + 512, 1024, 2048, 4096. If property is not found, default value
> + of 512 will be used.
> + - For compatible property "qcom,spmi-adc5", valid values are 250, 420
> + and 840. If property is not found, default value of 840 is used.
> + - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
> + 512 and 1024. If property is not present, default value is 1024.
> + allOf:
> + - $ref: /schemas/types.yaml#/definitions/uint32
> Should ideally verify all the values against models etc rather than a uint32 binding.
I'll add constraints for all properties for which it's applicable in the
next post.
>
>> +
>> + qcom,pre-scaling:
>> + description: |
>> + Used for scaling the channel input signal before the signal is
>> + fed to VADC. The configuration for this node is to know the
>> + pre-determined ratio and use it for post scaling. Select one from
>> + the following options.
>> + <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
>
>> +
>> +examples:
>> + - |
>> + /* VADC node */
>> + pmic_vadc: vadc@3100 {
> Should really be using generic names, so adc@3100 preferred.
I'll change it in the next post.
Hi Rob,
On 3/30/2020 9:08 PM, Rob Herring wrote:
> On Tue, 24 Mar 2020 21:14:08 +0530, Jishnu Prakash wrote:
>> Convert the adc bindings from .txt to .yaml format.
>>
>> Signed-off-by: Jishnu Prakash <[email protected]>
>> ---
>> .../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 173 --------------------
>> .../bindings/iio/adc/qcom,spmi-vadc.yaml | 178 +++++++++++++++++++++
>> 2 files changed, 178 insertions(+), 173 deletions(-)
>> delete mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
>> create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>>
> My bot found errors running 'make dt_binding_check' on your patch:
>
> Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dts:20.11-26: Warning (reg_format): /example-0/vadc@3100:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
> Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dt.yaml: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
> Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dt.yaml: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
> Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dt.yaml: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.example.dt.yaml: vadc@3100: 'adc-chan@0x39' does not match any of the regexes: '.*-names$', '.*-supply$', '^#.*-cells$', '^#[a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$', '^__.*__$', 'pinctrl-[0-9]+'
>
> See https://patchwork.ozlabs.org/patch/1260800
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure dt-schema is up to date:
>
> pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
>
> Please check and re-submit.
I have checked it, I'll be fixing this in the next post.
Hi Amit,
On 4/3/2020 5:34 PM, Amit Kucheria wrote:
>
>> +required:
>> + - compatible
>> + - reg
>> + - '#address-cells'
>> + - '#size-cells'
>> + - '#io-channel-cells'
>> +
>> +patternProperties:
>> + "^[a-z0-9-_@]$":
>> + type: object
>> + description: |
>> + Represents the external channels which are connected to the ADC.
>> + For compatible property "qcom,spmi-vadc" following channels, also known as
>> + reference point channels, are used for result calibration and their channel
>> + configuration nodes should be defined:
>> + VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV,
>> + VADC_GND_REF and VADC_VDD_VADC.
> Instead of this note for "qcom,spmi-vadc", you can enforce this
> through checks in YAML grammar.
>
> A simple example can be found in
> Documentation/devicetree/bindings/thermal/qcom-tsens.yaml. Look for
> the if, then, else clause which determines how many interrupts need to
> be defined.
I have gone through tsens and other examples, but I'm not able to get a
way to apply this kind of constraint, on what child nodes should be present.
In this case, the constraint would have to be that for compatible
property "qcom,spmi-vadc", there should be at least four child nodes and
those four should have their "reg" property fixed to the channel values
mentioned above. I can see how to apply constraints on a single property
like interrupts in tsens, but I'm not sure if there is a way to specify
a lower limit to the number of child nodes or something like "there
should be at least one child node with value 0x9 for its "reg"
property". I could not find any examples with constraints placed on
number of occurrences of a child node.
Can you please share an example of such a constraint if you are aware of
any or suggest some way by which this kind of constraint can be specified?
>
>> +
>> + properties:
>> + reg:
>> + description: |
>> + ADC channel number.
>> + See include/dt-bindings/iio/qcom,spmi-vadc.h
>> +
>> + label:
>> + description: |
>> + ADC input of the platform as seen in the schematics.
>> + For thermistor inputs connected to generic AMUX or GPIO inputs
>> + these can vary across platform for the same pins. Hence select
>> + the platform schematics name for this channel. It is required
>> + for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2".
>> + allOf:
>> + - $ref: /schemas/types.yaml#/definitions/string
> You shouldn't need allOf here.
>
> Just a "$ref: /schemas/types.yaml#/definitions/string" should be fine.
> And move it above the description.
>
> Same for all the uses of allOf below.
I'll make the change in the next post.
>
>
>> + qcom,decimation:
>> + description: |
>> + This parameter is used to decrease ADC sampling rate.
>> + Quicker measurements can be made by reducing decimation ratio.
>> + - For compatible property "qcom,spmi-vadc", valid values are
>> + 512, 1024, 2048, 4096. If property is not found, default value
>> + of 512 will be used.
>> + - For compatible property "qcom,spmi-adc5", valid values are 250, 420
>> + and 840. If property is not found, default value of 840 is used.
>> + - For compatible property "qcom,spmi-adc-rev2", valid values are 256,
>> + 512 and 1024. If property is not present, default value is 1024.
>> + allOf:
>> + - $ref: /schemas/types.yaml#/definitions/uint32
>> +
> As pointed out by Jonathon, please enforce these by keying off the
> compatible property.
I'll do this for all properties for which it's applicable in the next post.
>
>> + qcom,pre-scaling:
>> + description: |
>> + Used for scaling the channel input signal before the signal is
>> + fed to VADC. The configuration for this node is to know the
>> + pre-determined ratio and use it for post scaling. Select one from
>> + the following options.
> Please improve this description from the old binding. Does <1 3> mean
> the signal is scaled 3x or 1/3x?
<1 3> means it is scaled down to 1/3rd of actual value. I'll add to the
description in the next post.
>
>> + <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
>> + If property is not found default value depending on chip will be used.
>> + allOf:
>> + - $ref: /schemas/types.yaml#/definitions/uint32
>> +
Hi Jonathan,
On 3/28/2020 10:24 PM, Jonathan Cameron wrote:
> On Tue, 24 Mar 2020 21:14:09 +0530
> Jishnu Prakash <[email protected]> wrote:
>
>> Add documentation for PMIC7 ADC peripheral. For PMIC7 ADC, all SW
>> communication to ADC goes through PMK8350, which communicates with
>> other PMICs through PBS.
>>
>> Signed-off-by: Jishnu Prakash <[email protected]>
>> ---
>> .../bindings/iio/adc/qcom,spmi-vadc.yaml | 28 ++++++++++++++++------
>> 1 file changed, 21 insertions(+), 7 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>> index 72db14c..20f010c 100644
>> --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>> @@ -13,7 +13,7 @@ maintainers:
>> description: |
>> SPMI PMIC voltage ADC (VADC) provides interface to clients to read
>> voltage. The VADC is a 15-bit sigma-delta ADC.
>> - SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
>> + SPMI PMIC5/PMIC7 voltage ADC (ADC) provides interface to clients to read
>> voltage. The VADC is a 16-bit sigma-delta ADC.
>>
>> properties:
>> @@ -23,6 +23,7 @@ properties:
>> - qcom,spmi-adc5
>> - qcom,spmi-adc-rev2
>> - qcom,pms405-adc
>> + - qcom,spmi-adc7
>>
>> reg:
>> description: VADC base address in the SPMI PMIC register map
>> @@ -65,6 +66,8 @@ patternProperties:
>> description: |
>> ADC channel number.
>> See include/dt-bindings/iio/qcom,spmi-vadc.h
>> + For PMIC7 ADC, the channel numbers are specified separately per PMIC
>> + in the PMIC-specific files in include/dt-bindings/iio/.
> That makes me thing we really should have separate compatibles. The
> parts clearly have differences, even if we haven't needed to use them
> explicitly as yet.
I'm not sure what you mean by this. We have added a new compatible
property "qcom,spmi-adc7" for PMIC7 ADC.
>
>>
>> label:
>> description: |
>> @@ -72,7 +75,7 @@ patternProperties:
>> For thermistor inputs connected to generic AMUX or GPIO inputs
>> these can vary across platform for the same pins. Hence select
>> the platform schematics name for this channel. It is required
>> - for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2".
>> + for "qcom,spmi-adc5", "qcom,spmi-adc7" and "qcom,spmi-adc-rev2".
>> allOf:
>> - $ref: /schemas/types.yaml#/definitions/string
>>
>>
Hi Amit,
On 4/3/2020 5:41 PM, Amit Kucheria wrote:
> Hi Jishnu,
>
> On Tue, Mar 24, 2020 at 9:15 PM Jishnu Prakash <[email protected]> wrote:
>> Add documentation for PMIC7 ADC peripheral. For PMIC7 ADC, all SW
>> communication to ADC goes through PMK8350, which communicates with
>> other PMICs through PBS.
> What is PMK8350? What is PBS? Please expand the acronyms and describe
> more verbosely.
PMK8350 is just the name of one of the PMIC7 family of PMICs. I'll
expand the description in the next post.
>
>> Signed-off-by: Jishnu Prakash <[email protected]>
>> ---
>> .../bindings/iio/adc/qcom,spmi-vadc.yaml | 28 ++++++++++++++++------
>> 1 file changed, 21 insertions(+), 7 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>> index 72db14c..20f010c 100644
>> --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
>> @@ -13,7 +13,7 @@ maintainers:
>> description: |
>> SPMI PMIC voltage ADC (VADC) provides interface to clients to read
>> voltage. The VADC is a 15-bit sigma-delta ADC.
>> - SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
>> + SPMI PMIC5/PMIC7 voltage ADC (ADC) provides interface to clients to read
>> voltage. The VADC is a 16-bit sigma-delta ADC.
>>
>>
Hi Jonathan,
On 3/28/2020 10:34 PM, Jonathan Cameron wrote:
> On Tue, 24 Mar 2020 21:14:10 +0530
> Jishnu Prakash <[email protected]> wrote:
>
>> The ADC architecture on PMIC7 is changed as compared to PMIC5. The
>> major change from PMIC5 is that all SW communication to ADC goes through
>> PMK8350, which communicates with other PMICs through PBS when the ADC
>> on PMK8350 works in master mode. The SID register is used to identify the
>> PMICs with which the PBS needs to communicate. Add support for the same.
>>
>> In addition, add definitions for ADC channels and virtual channel
>> definitions per PMIC, to be used by ADC clients for PMIC7.
>>
>> Signed-off-by: Jishnu Prakash <[email protected]>
> A few additions from me.
>
>> ---
> ...
>
> I'll address your comments in the next post.
Hi Andy,
On 3/24/2020 10:03 PM, Andy Shevchenko wrote:
> On Tue, Mar 24, 2020 at 5:46 PM Jishnu Prakash <[email protected]> wrote:
>> The ADC architecture on PMIC7 is changed as compared to PMIC5. The
>> major change from PMIC5 is that all SW communication to ADC goes through
>> PMK8350, which communicates with other PMICs through PBS when the ADC
>> on PMK8350 works in master mode. The SID register is used to identify the
>> PMICs with which the PBS needs to communicate. Add support for the same.
>>
>> In addition, add definitions for ADC channels and virtual channel
>> definitions per PMIC, to be used by ADC clients for PMIC7.
> ...
>
>> +#define ADC_CHANNEL_OFFSET 0x8
>> +#define ADC_CHANNEL_MASK 0xff
> GENMASK()
I'll fix this and the other simple changes in the next post.
>
> ...
>
>> +#define ADC_APP_SID 0x40
>> +#define ADC_APP_SID_MASK 0xf
> GENMASK()
>
>> +#define ADC7_CONV_TIMEOUT msecs_to_jiffies(10)
> Useless.
I'm not sure what you mean by this. It is used in the API
adc7_do_conversion.
> ...
>
> + if (of_device_is_compatible(node, "qcom,spmi-adc7")) {
>> + indio_dev->info = &adc7_info;
>> + adc->is_pmic7 = true;
>> + } else {
>> + indio_dev->info = &adc5_info;
>> + }
> Hmm... I would rather put this as driver_data in ID structure(s).
I'll remove the check for the compatible string, using driver data, in
the next post.
>
> ...
>
>> +static int adc5_exit(struct platform_device *pdev)
>> +{
>> + struct adc5_chip *adc = platform_get_drvdata(pdev);
>> +
>> + mutex_destroy(&adc->lock);
> Are you sure you will have no race conditions? Does this driver use IRQs?
The driver does use an IRQ. Will fix this in the next post.
>
>
Hi Rob
On 4/1/2020 1:36 AM, Rob Herring wrote:
> On Tue, Mar 24, 2020 at 09:14:10PM +0530, Jishnu Prakash wrote:
>> The ADC architecture on PMIC7 is changed as compared to PMIC5. The
>> major change from PMIC5 is that all SW communication to ADC goes through
>> PMK8350, which communicates with other PMICs through PBS when the ADC
>> on PMK8350 works in master mode. The SID register is used to identify the
>> PMICs with which the PBS needs to communicate. Add support for the same.
>>
>> In addition, add definitions for ADC channels and virtual channel
>> definitions per PMIC, to be used by ADC clients for PMIC7.
>>
>> Signed-off-by: Jishnu Prakash <[email protected]>
>> ---
>> drivers/iio/adc/qcom-spmi-adc5.c | 239 ++++++++++++++++++++-
>> drivers/iio/adc/qcom-vadc-common.c | 260 +++++++++++++++++++++++
>> drivers/iio/adc/qcom-vadc-common.h | 14 ++
>> include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h | 67 ++++++
>> include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h | 88 ++++++++
>> include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h | 46 ++++
>> include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h | 28 +++
>> include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h | 28 +++
>> include/dt-bindings/iio/qcom,spmi-vadc.h | 78 ++++++-
> DT headers go in the binding patch(es).
I'll move these to the bindings patch in the next post.
>
>> 9 files changed, 843 insertions(+), 5 deletions(-)
>> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pm8350.h
>> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pm8350b.h
>> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmk8350.h
>> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmr735a.h
>> create mode 100644 include/dt-bindings/iio/qcom,spmi-adc7-pmr735b.h
On Mon, 6 Apr 2020 17:15:21 +0530
Jishnu Prakash <[email protected]> wrote:
> Hi Jonathan,
>
> On 3/28/2020 10:24 PM, Jonathan Cameron wrote:
> > On Tue, 24 Mar 2020 21:14:09 +0530
> > Jishnu Prakash <[email protected]> wrote:
> >
> >> Add documentation for PMIC7 ADC peripheral. For PMIC7 ADC, all SW
> >> communication to ADC goes through PMK8350, which communicates with
> >> other PMICs through PBS.
> >>
> >> Signed-off-by: Jishnu Prakash <[email protected]>
> >> ---
> >> .../bindings/iio/adc/qcom,spmi-vadc.yaml | 28 ++++++++++++++++------
> >> 1 file changed, 21 insertions(+), 7 deletions(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> >> index 72db14c..20f010c 100644
> >> --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> >> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.yaml
> >> @@ -13,7 +13,7 @@ maintainers:
> >> description: |
> >> SPMI PMIC voltage ADC (VADC) provides interface to clients to read
> >> voltage. The VADC is a 15-bit sigma-delta ADC.
> >> - SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read
> >> + SPMI PMIC5/PMIC7 voltage ADC (ADC) provides interface to clients to read
> >> voltage. The VADC is a 16-bit sigma-delta ADC.
> >>
> >> properties:
> >> @@ -23,6 +23,7 @@ properties:
> >> - qcom,spmi-adc5
> >> - qcom,spmi-adc-rev2
> >> - qcom,pms405-adc
> >> + - qcom,spmi-adc7
> >>
> >> reg:
> >> description: VADC base address in the SPMI PMIC register map
> >> @@ -65,6 +66,8 @@ patternProperties:
> >> description: |
> >> ADC channel number.
> >> See include/dt-bindings/iio/qcom,spmi-vadc.h
> >> + For PMIC7 ADC, the channel numbers are specified separately per PMIC
> >> + in the PMIC-specific files in include/dt-bindings/iio/.
> > That makes me thing we really should have separate compatibles. The
> > parts clearly have differences, even if we haven't needed to use them
> > explicitly as yet.
> I'm not sure what you mean by this. We have added a new compatible
> property "qcom,spmi-adc7" for PMIC7 ADC.
I've no idea what I meant either :)
Jonathan
> >
> >>
> >> label:
> >> description: |
> >> @@ -72,7 +75,7 @@ patternProperties:
> >> For thermistor inputs connected to generic AMUX or GPIO inputs
> >> these can vary across platform for the same pins. Hence select
> >> the platform schematics name for this channel. It is required
> >> - for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2".
> >> + for "qcom,spmi-adc5", "qcom,spmi-adc7" and "qcom,spmi-adc-rev2".
> >> allOf:
> >> - $ref: /schemas/types.yaml#/definitions/string
> >>
> >>
On Mon, Apr 6, 2020 at 5:15 PM Jishnu Prakash <[email protected]> wrote:
>
> Hi Amit,
>
> On 4/3/2020 5:34 PM, Amit Kucheria wrote:
> >
> >> +required:
> >> + - compatible
> >> + - reg
> >> + - '#address-cells'
> >> + - '#size-cells'
> >> + - '#io-channel-cells'
> >> +
> >> +patternProperties:
> >> + "^[a-z0-9-_@]$":
> >> + type: object
> >> + description: |
> >> + Represents the external channels which are connected to the ADC.
> >> + For compatible property "qcom,spmi-vadc" following channels, also known as
> >> + reference point channels, are used for result calibration and their channel
> >> + configuration nodes should be defined:
> >> + VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV,
> >> + VADC_GND_REF and VADC_VDD_VADC.
> > Instead of this note for "qcom,spmi-vadc", you can enforce this
> > through checks in YAML grammar.
> >
> > A simple example can be found in
> > Documentation/devicetree/bindings/thermal/qcom-tsens.yaml. Look for
> > the if, then, else clause which determines how many interrupts need to
> > be defined.
>
> I have gone through tsens and other examples, but I'm not able to get a
> way to apply this kind of constraint, on what child nodes should be present.
>
> In this case, the constraint would have to be that for compatible
> property "qcom,spmi-vadc", there should be at least four child nodes and
> those four should have their "reg" property fixed to the channel values
> mentioned above. I can see how to apply constraints on a single property
> like interrupts in tsens, but I'm not sure if there is a way to specify
> a lower limit to the number of child nodes or something like "there
> should be at least one child node with value 0x9 for its "reg"
> property". I could not find any examples with constraints placed on
> number of occurrences of a child node.
>
> Can you please share an example of such a constraint if you are aware of
> any or suggest some way by which this kind of constraint can be specified?
Hi Jishnu,
I misread that particular property. I don't think it is possible to
specify child nodes w/o splitting this binding into two, I think.
Please go ahead with the rest of changes. I'll keep digging to see if
this is possible.
Regards,
Amit