Add QSPI controller support for Intel LGM SoC.
Note from Vignesh(mtd subsystem maintainer):
This series is a subset of "[PATCH v12 0/4] spi: cadence-quadspi: Add
support for the Cadence QSPI controller" by Ramuthevar,Vadivel MuruganX
<[email protected]> that intended to move
cadence-quadspi driver to spi-mem framework
Those patches were trying to accomplish too many things in a single set
of patches and need to split into smaller patches. This is reduced
version of above series.
Changes that are intended to make migration easy are split into separate
patches. Patches 1 to 3 drop features that cannot be supported under
spi-mem at the moment (backward compatibility is maintained).
Patch 4-5 are trivial cleanups. Patch 6 does the actual conversion to
spi-mem and patch 7 moves the driver to drivers/spi folder.
I have tested both INDAC mode (used by non TI platforms like Altera
SoCFPGA) and DAC mode (used by TI platforms) on TI EVMs.
Patches to move move bindings over to
"Documentation/devicetree/bindings/spi/" directory and also conversion
of bindig doc to YAML will be posted separately. Support for Intel
platform would follow that.
Reference:
https://lkml.org/lkml/2020/6/1/50
---
v7:
- Rob's review comments address and fixed dt-schema warning
- Pratyush review comments address and update
- DAC bit reset to 0 and 1 (enable/disable)
- tested QSI-NOR flash mx25l12805d on LGM soc, it's working after disable DAC
- Linus suggested to use 'num-cs' prperty instead of 'num-chipselect'
v6:
- Rob's review comments update
- add compatible string in properly aligned
- remove cadence-qspi extra comaptible string in example
v5:
- Rob's review comments update
- const with single compatible string kept
v4:
- Rob's review comments update
- remove '|' no formatting to preserve
- child node attributes follows under 'properties' under '@[0-9a-f]+$'.
v3:
- Pratyush review comments update
- CQSPI_SUPPORTS_MULTI_CHIPSELECT macro used instead of cqspi->use_direct_mode
- disable DAC support placed in end of controller_init
v2:
- Rob's review comments update for dt-bindings
- add 'oneOf' for compatible selection
- drop un-neccessary descriptions
- add the cdns,is-decoded-cs and cdns,rclk-en properties as schema
- remove 'allOf' in not required place
- add AdditionalProperties false
- add minItems/maxItems for qspi reset attributes
resend-v1:
- As per Mark's suggestion , reorder the patch series 1-3 driver
support patches, series 4-6 dt-bindings patches.
v1:
- initial version
Ramuthevar Vadivel Murugan (6):
spi: cadence-quadspi: Add QSPI support for Intel LGM SoC
spi: cadence-quadspi: Disable the DAC for Intel LGM SoC
spi: cadence-quadspi: Add multi-chipselect support for Intel LGM SoC
spi: Move cadence-quadspi.txt to Documentation/devicetree/bindings/spi
dt-bindings: spi: Convert cadence-quadspi.txt to cadence-quadspi.yaml
dt-bindings: spi: Add compatible for Intel LGM SoC
.../devicetree/bindings/mtd/cadence-quadspi.txt | 67 ----------
.../devicetree/bindings/spi/cdns,qspi-nor.yaml | 148 +++++++++++++++++++++
drivers/spi/Kconfig | 2 +-
drivers/spi/spi-cadence-quadspi.c | 33 ++++-
4 files changed, 178 insertions(+), 72 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
--
2.11.0
From: Ramuthevar Vadivel Murugan <[email protected]>
Add QSPI controller support for Intel LGM SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
---
drivers/spi/Kconfig | 2 +-
drivers/spi/spi-cadence-quadspi.c | 3 +++
2 files changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index d2c976e55b8b..926da61eee5a 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -203,7 +203,7 @@ config SPI_CADENCE
config SPI_CADENCE_QUADSPI
tristate "Cadence Quad SPI controller"
- depends on OF && (ARM || ARM64 || COMPILE_TEST)
+ depends on OF && (ARM || ARM64 || X86 || COMPILE_TEST)
help
Enable support for the Cadence Quad SPI Flash controller.
diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index 40938cf3806d..d7b10c46fa70 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -1401,6 +1401,9 @@ static const struct of_device_id cqspi_dt_ids[] = {
.compatible = "ti,am654-ospi",
.data = &am654_ospi,
},
+ {
+ .compatible = "intel,lgm-qspi",
+ },
{ /* end of table */ }
};
--
2.11.0
From: Ramuthevar Vadivel Murugan <[email protected]>
On Intel Lightning Mountain(LGM) SoCs QSPI controller do not use
Direct Access Controller(DAC).
This patch adds a quirk to disable the Direct Access Controller
for data transfer instead it uses indirect data transfe
DAC bit resets to 1 so there is no need to explicitly set it.
Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
---
drivers/spi/spi-cadence-quadspi.c | 15 +++++++++++----
1 file changed, 11 insertions(+), 4 deletions(-)
diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index d7b10c46fa70..d12b765e87be 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -1101,10 +1101,12 @@ static void cqspi_controller_init(struct cqspi_st *cqspi)
writel(cqspi->fifo_depth * cqspi->fifo_width / 8,
cqspi->iobase + CQSPI_REG_INDIRECTWRWATERMARK);
- /* Enable Direct Access Controller */
- reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
- reg |= CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL;
- writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+ /* Disable direct access controller */
+ if (!cqspi->use_direct_mode) {
+ reg = readl(cqspi->iobase + CQSPI_REG_CONFIG);
+ reg &= ~CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL;
+ writel(reg, cqspi->iobase + CQSPI_REG_CONFIG);
+ }
cqspi_controller_enable(cqspi, 1);
}
@@ -1388,6 +1390,10 @@ static const struct cqspi_driver_platdata am654_ospi = {
.quirks = CQSPI_NEEDS_WR_DELAY,
};
+static const struct cqspi_driver_platdata intel_lgm_qspi = {
+ .quirks = CQSPI_DISABLE_DAC_MODE,
+};
+
static const struct of_device_id cqspi_dt_ids[] = {
{
.compatible = "cdns,qspi-nor",
@@ -1403,6 +1409,7 @@ static const struct of_device_id cqspi_dt_ids[] = {
},
{
.compatible = "intel,lgm-qspi",
+ .data = &intel_lgm_qspi,
},
{ /* end of table */ }
};
--
2.11.0
From: Ramuthevar Vadivel Murugan <[email protected]>
Move the Documentation/devicetree/bindings/mtd/cadence-quadspi.txt to
Documentation/devicetree/bindings/spi/
Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/{mtd => spi}/cadence-quadspi.txt | 0
1 file changed, 0 insertions(+), 0 deletions(-)
rename Documentation/devicetree/bindings/{mtd => spi}/cadence-quadspi.txt (100%)
diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
similarity index 100%
rename from Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
rename to Documentation/devicetree/bindings/spi/cadence-quadspi.txt
--
2.11.0
From: Ramuthevar Vadivel Murugan <[email protected]>
Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
---
.../devicetree/bindings/spi/cadence-quadspi.txt | 67 ----------
.../devicetree/bindings/spi/cdns,qspi-nor.yaml | 147 +++++++++++++++++++++
2 files changed, 147 insertions(+), 67 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
deleted file mode 100644
index 945be7d5b236..000000000000
--- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
+++ /dev/null
@@ -1,67 +0,0 @@
-* Cadence Quad SPI controller
-
-Required properties:
-- compatible : should be one of the following:
- Generic default - "cdns,qspi-nor".
- For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
- For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
-- reg : Contains two entries, each of which is a tuple consisting of a
- physical address and length. The first entry is the address and
- length of the controller register set. The second entry is the
- address and length of the QSPI Controller data area.
-- interrupts : Unit interrupt specifier for the controller interrupt.
-- clocks : phandle to the Quad SPI clock.
-- cdns,fifo-depth : Size of the data FIFO in words.
-- cdns,fifo-width : Bus width of the data FIFO in bytes.
-- cdns,trigger-address : 32-bit indirect AHB trigger address.
-
-Optional properties:
-- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
-- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
- the read data rather than the QSPI clock. Make sure that QSPI return
- clock is populated on the board before using this property.
-
-Optional subnodes:
-Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
-custom properties:
-- cdns,read-delay : Delay for read capture logic, in clock cycles
-- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
- mode chip select outputs are de-asserted between
- transactions.
-- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
- de-activated and the activation of another.
-- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
- transaction and deasserting the device chip select
- (qspi_n_ss_out).
-- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
- and first bit transfer.
-- resets : Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
-- reset-names : Must include either "qspi" and/or "qspi-ocp".
-
-Example:
-
- qspi: spi@ff705000 {
- compatible = "cdns,qspi-nor";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0xff705000 0x1000>,
- <0xffa00000 0x1000>;
- interrupts = <0 151 4>;
- clocks = <&qspi_clk>;
- cdns,is-decoded-cs;
- cdns,fifo-depth = <128>;
- cdns,fifo-width = <4>;
- cdns,trigger-address = <0x00000000>;
- resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
- reset-names = "qspi", "qspi-ocp";
-
- flash0: n25q00@0 {
- ...
- cdns,read-delay = <4>;
- cdns,tshsl-ns = <50>;
- cdns,tsd2d-ns = <50>;
- cdns,tchsh-ns = <4>;
- cdns,tslch-ns = <4>;
- };
- };
diff --git a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
new file mode 100644
index 000000000000..5fc54182ed74
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
@@ -0,0 +1,147 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence Quad SPI controller
+
+maintainers:
+ - Vadivel Murugan <[email protected]>
+
+allOf:
+ - $ref: spi-controller.yaml#
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - cdns,qspi-nor
+ - ti,k2g-qspi
+ - ti,am654-ospi
+
+ reg:
+ items:
+ - description: the controller register set
+ - description: the controller data area
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ cdns,fifo-depth:
+ description:
+ Size of the data FIFO in words.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum: [ 128, 256 ]
+ default: 128
+
+ cdns,fifo-width:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Bus width of the data FIFO in bytes.
+ default: 4
+
+ cdns,trigger-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ 32-bit indirect AHB trigger address.
+
+ cdns,is-decoded-cs:
+ type: boolean
+ description:
+ Flag to indicate whether decoder is used to select different chip select
+ for different memory regions.
+
+ cdns,rclk-en:
+ type: boolean
+ description:
+ Flag to indicate that QSPI return clock is used to latch the read
+ data rather than the QSPI clock. Make sure that QSPI return clock
+ is populated on the board before using this property.
+
+ resets:
+ maxItems: 2
+
+ reset-names:
+ minItems: 1
+ maxItems: 2
+ items:
+ enum: [ qspi, qspi-ocp ]
+
+# subnode's properties
+patternProperties:
+ "@[0-9a-f]+$":
+ type: object
+ description:
+ flash device uses the subnodes below defined properties.
+ properties:
+ cdns,read-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Delay for read capture logic, in clock cycles.
+
+ cdns,tshsl-ns:
+ description:
+ Delay in nanoseconds for the length that the master mode chip select
+ outputs are de-asserted between transactions.
+
+ cdns,tsd2d-ns:
+ description:
+ Delay in nanoseconds between one chip select being de-activated
+ and the activation of another.
+
+ cdns,tchsh-ns:
+ description:
+ Delay in nanoseconds between last bit of current transaction and
+ deasserting the device chip select (qspi_n_ss_out).
+
+ cdns,tslch-ns:
+ description:
+ Delay in nanoseconds between setting qspi_n_ss_out low and
+ first bit transfer.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - cdns,fifo-depth
+ - cdns,fifo-width
+ - cdns,trigger-address
+ - resets
+ - reset-names
+ - '#address-cells'
+ - '#size-cells'
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ qspi: spi@ff705000 {
+ compatible = "cdns,qspi-nor";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xff705000 0x1000>,
+ <0xffa00000 0x1000>;
+ interrupts = <0 151 4>;
+ clocks = <&qspi_clk>;
+ cdns,fifo-depth = <128>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x00000000>;
+ resets = <&rst 0x1>, <&rst 0x2>;
+ reset-names = "qspi", "qspi-ocp";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ cdns,read-delay = <4>;
+ cdns,tshsl-ns = <50>;
+ cdns,tsd2d-ns = <50>;
+ cdns,tchsh-ns = <4>;
+ cdns,tslch-ns = <4>;
+ };
+
+ };
--
2.11.0
From: Ramuthevar Vadivel Murugan <[email protected]>
Add compatible for Intel LGM SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
---
Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
index 5fc54182ed74..1f7c6b471ec1 100644
--- a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
+++ b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
@@ -19,6 +19,7 @@ properties:
- cdns,qspi-nor
- ti,k2g-qspi
- ti,am654-ospi
+ - intel,lgm-qspi
reg:
items:
--
2.11.0
From: Ramuthevar Vadivel Murugan <[email protected]>
Add multiple chipselect support for Intel LGM SoCs,
currently QSPI-NOR and QSPI-NAND supported.
Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
---
drivers/spi/spi-cadence-quadspi.c | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index d12b765e87be..337778f75d5d 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -38,6 +38,7 @@
/* Capabilities */
#define CQSPI_SUPPORTS_OCTAL BIT(0)
+#define CQSPI_SUPPORTS_MULTI_CHIPSELECT BIT(1)
struct cqspi_st;
@@ -75,6 +76,7 @@ struct cqspi_st {
bool is_decoded_cs;
u32 fifo_depth;
u32 fifo_width;
+ u32 num_chipselect;
bool rclk_en;
u32 trigger_address;
u32 wr_delay;
@@ -1049,6 +1051,7 @@ static int cqspi_of_get_flash_pdata(struct platform_device *pdev,
static int cqspi_of_get_pdata(struct cqspi_st *cqspi)
{
+ const struct cqspi_driver_platdata *ddata;
struct device *dev = &cqspi->pdev->dev;
struct device_node *np = dev->of_node;
@@ -1070,6 +1073,14 @@ static int cqspi_of_get_pdata(struct cqspi_st *cqspi)
return -ENXIO;
}
+ ddata = of_device_get_match_data(dev);
+ if (ddata->hwcaps_mask & CQSPI_SUPPORTS_MULTI_CHIPSELECT) {
+ if (of_property_read_u32(np, "num-cs", &cqspi->num_chipselect)) {
+ dev_err(dev, "couldn't determine number of cs\n");
+ return -ENXIO;
+ }
+ }
+
cqspi->rclk_en = of_property_read_bool(np, "cdns,rclk-en");
return 0;
@@ -1302,6 +1313,9 @@ static int cqspi_probe(struct platform_device *pdev)
cqspi->current_cs = -1;
cqspi->sclk = 0;
+ if (ddata->hwcaps_mask & CQSPI_SUPPORTS_MULTI_CHIPSELECT)
+ master->num_chipselect = cqspi->num_chipselect;
+
ret = cqspi_setup_flash(cqspi);
if (ret) {
dev_err(dev, "failed to setup flash parameters %d\n", ret);
@@ -1391,6 +1405,7 @@ static const struct cqspi_driver_platdata am654_ospi = {
};
static const struct cqspi_driver_platdata intel_lgm_qspi = {
+ .hwcaps_mask = CQSPI_SUPPORTS_MULTI_CHIPSELECT,
.quirks = CQSPI_DISABLE_DAC_MODE,
};
--
2.11.0
On Mon, Nov 16, 2020 at 11:10:02AM +0800, Ramuthevar,Vadivel MuruganX wrote:
> From: Ramuthevar Vadivel Murugan <[email protected]>
>
> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
>
> Signed-off-by: Ramuthevar Vadivel Murugan <[email protected]>
> ---
> .../devicetree/bindings/spi/cadence-quadspi.txt | 67 ----------
> .../devicetree/bindings/spi/cdns,qspi-nor.yaml | 147 +++++++++++++++++++++
> 2 files changed, 147 insertions(+), 67 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
>
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> deleted file mode 100644
> index 945be7d5b236..000000000000
> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> +++ /dev/null
> @@ -1,67 +0,0 @@
> -* Cadence Quad SPI controller
> -
WTF?
> -Required properties:
> -- compatible : should be one of the following:
> - Generic default - "cdns,qspi-nor".
> - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
> +properties:
> + compatible:
> + items:
> + - enum:
> + - cdns,qspi-nor
> + - ti,k2g-qspi
> + - ti,am654-ospi
> +examples:
> + - |
> + qspi: spi@ff705000 {
> + compatible = "cdns,qspi-nor";
I give up.
On Mon, Nov 16, 2020 at 11:10:02AM +0800, Ramuthevar,Vadivel MuruganX wrote:
> From: Ramuthevar Vadivel Murugan <[email protected]>
>
> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
As previously and repeatedly requested please make any conversions to
YAML the *final* thing in serieses so that issues with the conversion do
not hold up other development.
Hi Mark,
On 17/11/2020 3:07 am, Mark Brown wrote:
> On Mon, Nov 16, 2020 at 11:10:02AM +0800, Ramuthevar,Vadivel MuruganX wrote:
>> From: Ramuthevar Vadivel Murugan <[email protected]>
>>
>> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
>> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
>
> As previously and repeatedly requested please make any conversions to
> YAML the *final* thing in serieses so that issues with the conversion do
> not hold up other development.
Thank you for the suggestions...
I understood like order of series to be changed, that's the reason
added-up YAML conversion patches at the end of series, sorry I will drop
the patches of YAML conversion.
Regards
Vadivel
>