These patches are orginally from the series
"net: dsa: microchip: PTP support for KSZ956x"
As the the device tree conversion to yaml is not really related to the
PTP patches and the original series is going to take more time than
I expected, I would like to split this.
Changes (original series -> v1)
--------------------------------
- dts: moved "allOf" below "maintainers"
- dts: use "unevaluatedProperties" instead of "additionalProperties"
- dts: removed "spi-cpha" and "spi-cpol" flags as the hardware is fixed
- ksz8795: setup SPI for mode 3
- ksz9477: dito
Convert the bindings document for Microchip KSZ Series Ethernet switches
from txt to yaml. Removed spi-cpha and spi-cpol flags is this should be
handled by the device driver.
Signed-off-by: Christian Eggers <[email protected]>
---
.../devicetree/bindings/net/dsa/ksz.txt | 125 ---------------
.../bindings/net/dsa/microchip,ksz.yaml | 148 ++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 149 insertions(+), 126 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/net/dsa/ksz.txt
create mode 100644 Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml
diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt
deleted file mode 100644
index 95e91e84151c..000000000000
--- a/Documentation/devicetree/bindings/net/dsa/ksz.txt
+++ /dev/null
@@ -1,125 +0,0 @@
-Microchip KSZ Series Ethernet switches
-==================================
-
-Required properties:
-
-- compatible: For external switch chips, compatible string must be exactly one
- of the following:
- - "microchip,ksz8765"
- - "microchip,ksz8794"
- - "microchip,ksz8795"
- - "microchip,ksz9477"
- - "microchip,ksz9897"
- - "microchip,ksz9896"
- - "microchip,ksz9567"
- - "microchip,ksz8565"
- - "microchip,ksz9893"
- - "microchip,ksz9563"
- - "microchip,ksz8563"
-
-Optional properties:
-
-- reset-gpios : Should be a gpio specifier for a reset line
-- microchip,synclko-125 : Set if the output SYNCLKO frequency should be set to
- 125MHz instead of 25MHz.
-
-See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
-required and optional properties.
-
-Examples:
-
-Ethernet switch connected via SPI to the host, CPU port wired to eth0:
-
- eth0: ethernet@10001000 {
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- spi1: spi@f8008000 {
- pinctrl-0 = <&pinctrl_spi_ksz>;
- cs-gpios = <&pioC 25 0>;
- id = <1>;
-
- ksz9477: ksz9477@0 {
- compatible = "microchip,ksz9477";
- reg = <0>;
-
- spi-max-frequency = <44000000>;
- spi-cpha;
- spi-cpol;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- label = "lan1";
- };
- port@1 {
- reg = <1>;
- label = "lan2";
- };
- port@2 {
- reg = <2>;
- label = "lan3";
- };
- port@3 {
- reg = <3>;
- label = "lan4";
- };
- port@4 {
- reg = <4>;
- label = "lan5";
- };
- port@5 {
- reg = <5>;
- label = "cpu";
- ethernet = <ð0>;
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
- };
- ksz8565: ksz8565@0 {
- compatible = "microchip,ksz8565";
- reg = <0>;
-
- spi-max-frequency = <44000000>;
- spi-cpha;
- spi-cpol;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- port@0 {
- reg = <0>;
- label = "lan1";
- };
- port@1 {
- reg = <1>;
- label = "lan2";
- };
- port@2 {
- reg = <2>;
- label = "lan3";
- };
- port@3 {
- reg = <3>;
- label = "lan4";
- };
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <ð0>;
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml
new file mode 100644
index 000000000000..9f7d131bbcef
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml
@@ -0,0 +1,148 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/microchip,ksz.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip KSZ Series Ethernet switches
+
+maintainers:
+ - Marek Vasut <[email protected]>
+ - Woojung Huh <[email protected]>
+
+allOf:
+ - $ref: dsa.yaml#
+
+properties:
+ # See Documentation/devicetree/bindings/net/dsa/dsa.yaml for a list of additional
+ # required and optional properties.
+ compatible:
+ enum:
+ - microchip,ksz8765
+ - microchip,ksz8794
+ - microchip,ksz8795
+ - microchip,ksz9477
+ - microchip,ksz9897
+ - microchip,ksz9896
+ - microchip,ksz9567
+ - microchip,ksz8565
+ - microchip,ksz9893
+ - microchip,ksz9563
+ - microchip,ksz8563
+
+ reset-gpios:
+ description:
+ Should be a gpio specifier for a reset line.
+ maxItems: 1
+
+ microchip,synclko-125:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Set if the output SYNCLKO frequency should be set to 125MHz instead of 25MHz.
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ // Ethernet switch connected via SPI to the host, CPU port wired to eth0:
+ eth0 {
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ spi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&pinctrl_spi_ksz>;
+ cs-gpios = <&pioC 25 0>;
+ id = <1>;
+
+ ksz9477: switch@0 {
+ compatible = "microchip,ksz9477";
+ reg = <0>;
+ reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+
+ spi-max-frequency = <44000000>;
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ port@4 {
+ reg = <4>;
+ label = "lan5";
+ };
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <ð0>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+
+ ksz8565: switch@1 {
+ compatible = "microchip,ksz8565";
+ reg = <1>;
+
+ spi-max-frequency = <44000000>;
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <ð0>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 18b5b7896af8..d1003033412f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11508,7 +11508,7 @@ M: Woojung Huh <[email protected]>
M: Microchip Linux Driver Support <[email protected]>
L: [email protected]
S: Maintained
-F: Documentation/devicetree/bindings/net/dsa/ksz.txt
+F: Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml
F: drivers/net/dsa/microchip/*
F: include/linux/platform_data/microchip-ksz.h
F: net/dsa/tag_ksz.c
--
Christian Eggers
Embedded software developer
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRA 57918
Persoenlich haftender Gesellschafter: Arnold & Richter Cine Technik GmbH
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRB 54477
Geschaeftsfuehrer: Dr. Michael Neuhaeuser; Stephan Schenk; Walter Trauninger; Markus Zeiler
The dsa.yaml device tree binding allows "ethernet-ports" (preferred) and
"ports".
Signed-off-by: Christian Eggers <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
---
drivers/net/dsa/microchip/ksz_common.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 71cd1828e25d..a135fd5a9264 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -427,7 +427,9 @@ int ksz_switch_register(struct ksz_device *dev,
ret = of_get_phy_mode(dev->dev->of_node, &interface);
if (ret == 0)
dev->compat_interface = interface;
- ports = of_get_child_by_name(dev->dev->of_node, "ports");
+ ports = of_get_child_by_name(dev->dev->of_node, "ethernet-ports");
+ if (!ports)
+ ports = of_get_child_by_name(dev->dev->of_node, "ports");
if (ports)
for_each_available_child_of_node(ports, port) {
if (of_property_read_u32(port, "reg",
--
Christian Eggers
Embedded software developer
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRA 57918
Persoenlich haftender Gesellschafter: Arnold & Richter Cine Technik GmbH
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRB 54477
Geschaeftsfuehrer: Dr. Michael Neuhaeuser; Stephan Schenk; Walter Trauninger; Markus Zeiler
This should be done in the device driver instead of the device tree.
Signed-off-by: Christian Eggers <[email protected]>
---
drivers/net/dsa/microchip/ksz9477_spi.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/net/dsa/microchip/ksz9477_spi.c b/drivers/net/dsa/microchip/ksz9477_spi.c
index 1142768969c2..15bc11b3cda4 100644
--- a/drivers/net/dsa/microchip/ksz9477_spi.c
+++ b/drivers/net/dsa/microchip/ksz9477_spi.c
@@ -48,6 +48,12 @@ static int ksz9477_spi_probe(struct spi_device *spi)
if (spi->dev.platform_data)
dev->pdata = spi->dev.platform_data;
+ /* setup spi */
+ spi->mode = SPI_MODE_3;
+ ret = spi_setup(spi);
+ if (ret)
+ return ret;
+
ret = ksz9477_switch_register(dev);
/* Main DSA driver may not be started yet. */
--
Christian Eggers
Embedded software developer
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRA 57918
Persoenlich haftender Gesellschafter: Arnold & Richter Cine Technik GmbH
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRB 54477
Geschaeftsfuehrer: Dr. Michael Neuhaeuser; Stephan Schenk; Walter Trauninger; Markus Zeiler
This should be done in the device driver instead of the device tree.
Signed-off-by: Christian Eggers <[email protected]>
---
drivers/net/dsa/microchip/ksz8795_spi.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/net/dsa/microchip/ksz8795_spi.c b/drivers/net/dsa/microchip/ksz8795_spi.c
index 8b00f8e6c02f..f98432a3e2b5 100644
--- a/drivers/net/dsa/microchip/ksz8795_spi.c
+++ b/drivers/net/dsa/microchip/ksz8795_spi.c
@@ -49,6 +49,12 @@ static int ksz8795_spi_probe(struct spi_device *spi)
if (spi->dev.platform_data)
dev->pdata = spi->dev.platform_data;
+ /* setup spi */
+ spi->mode = SPI_MODE_3;
+ ret = spi_setup(spi);
+ if (ret)
+ return ret;
+
ret = ksz8795_switch_register(dev);
/* Main DSA driver may not be started yet. */
--
Christian Eggers
Embedded software developer
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRA 57918
Persoenlich haftender Gesellschafter: Arnold & Richter Cine Technik GmbH
Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRB 54477
Geschaeftsfuehrer: Dr. Michael Neuhaeuser; Stephan Schenk; Walter Trauninger; Markus Zeiler
Hello:
This series was applied to netdev/net-next.git (refs/heads/master):
On Fri, 20 Nov 2020 12:21:03 +0100 you wrote:
> These patches are orginally from the series
>
> "net: dsa: microchip: PTP support for KSZ956x"
>
> As the the device tree conversion to yaml is not really related to the
> PTP patches and the original series is going to take more time than
> I expected, I would like to split this.
>
> [...]
Here is the summary with links:
- [net-next,1/4] dt-bindings: net: dsa: convert ksz bindings document to yaml
https://git.kernel.org/netdev/net-next/c/4f36d97786c6
- [net-next,2/4] net: dsa: microchip: support for "ethernet-ports" node
https://git.kernel.org/netdev/net-next/c/44e53c88828f
- [net-next,3/4] net: dsa: microchip: ksz9477: setup SPI mode
https://git.kernel.org/netdev/net-next/c/9ed602bac971
- [net-next,4/4] net: dsa: microchip: ksz8795: setup SPI mode
https://git.kernel.org/netdev/net-next/c/8c4599f49841
You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html