Standalone ports should not have learning enabled since all the frames
are always copied to the CPU port. This is particularly important in
case an user-facing port intentionally spoofs the CPU port's MAC
address. With learning enabled we would end up with the switch having
incorrectly learned the address of the CPU port which typically results
in a complete break down of network connectivity until the address
learned ages out and gets re-learned, from the correct port this time.
There was no control of the BR_LEARNING flag until upstream commit
4098ced4680a485c5953f60ac63dff19f3fb3d42 ("Merge branch 'brport-flags'")
which is why we default to enabling learning when the ports gets added
as a bridge member.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 20 ++++++++++++++++++++
drivers/net/dsa/b53/b53_regs.h | 1 +
drivers/net/dsa/bcm_sf2.c | 5 +++++
drivers/net/dsa/bcm_sf2_regs.h | 2 ++
4 files changed, 28 insertions(+)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index 5ec0042bc384..b6867a8915da 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -502,6 +502,19 @@ static void b53_imp_vlan_setup(struct dsa_switch *ds, int cpu_port)
}
}
+static void b53_port_set_learning(struct b53_device *dev, int port,
+ bool learning)
+{
+ u16 reg;
+
+ b53_read16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, ®);
+ if (learning)
+ reg &= ~BIT(port);
+ else
+ reg |= BIT(port);
+ b53_write16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, reg);
+}
+
static int b53_enable_port(struct dsa_switch *ds, int port,
struct phy_device *phy)
{
@@ -509,6 +522,8 @@ static int b53_enable_port(struct dsa_switch *ds, int port,
unsigned int cpu_port = dev->cpu_port;
u16 pvlan;
+ b53_port_set_learning(dev, port, false);
+
/* Clear the Rx and Tx disable bits and set to no spanning tree */
b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(port), 0);
@@ -552,6 +567,8 @@ static void b53_enable_cpu_port(struct b53_device *dev)
PORT_CTRL_RX_MCST_EN |
PORT_CTRL_RX_UCST_EN;
b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(cpu_port), port_ctrl);
+
+ b53_port_set_learning(dev, cpu_port, false);
}
static void b53_enable_mib(struct b53_device *dev)
@@ -1375,6 +1392,8 @@ static int b53_br_join(struct dsa_switch *ds, int port,
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), pvlan);
dev->ports[port].vlan_ctl_mask = pvlan;
+ b53_port_set_learning(dev, port, true);
+
return 0;
}
@@ -1426,6 +1445,7 @@ static void b53_br_leave(struct dsa_switch *ds, int port)
vl->untag |= BIT(port) | BIT(dev->cpu_port);
b53_set_vlan_entry(dev, pvid, vl);
}
+ b53_port_set_learning(dev, port, false);
}
static void b53_br_set_stp_state(struct dsa_switch *ds, int port, u8 state)
diff --git a/drivers/net/dsa/b53/b53_regs.h b/drivers/net/dsa/b53/b53_regs.h
index 3cf246c6bdcc..aed70e76006d 100644
--- a/drivers/net/dsa/b53/b53_regs.h
+++ b/drivers/net/dsa/b53/b53_regs.h
@@ -112,6 +112,7 @@
#define B53_UC_FLOOD_MASK 0x32
#define B53_MC_FLOOD_MASK 0x34
#define B53_IPMC_FLOOD_MASK 0x36
+#define B53_DIS_LEARNING 0x3c
/*
* Override Ports 0-7 State on devices with xMII interfaces (8 bit)
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index a3742a3b413c..0c69d5858558 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -224,6 +224,11 @@ static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
+ /* Disable learning */
+ reg = core_readl(priv, CORE_DIS_LEARN);
+ reg |= BIT(port);
+ core_writel(priv, reg, CORE_DIS_LEARN);
+
/* Clear the Rx and Tx disable bits and set to no spanning tree */
core_writel(priv, 0, CORE_G_PCTL_PORT(port));
diff --git a/drivers/net/dsa/bcm_sf2_regs.h b/drivers/net/dsa/bcm_sf2_regs.h
index 838fe373cd6f..ca1d1f2e1161 100644
--- a/drivers/net/dsa/bcm_sf2_regs.h
+++ b/drivers/net/dsa/bcm_sf2_regs.h
@@ -138,6 +138,8 @@
#define CORE_SWITCH_CTRL 0x00088
#define MII_DUMB_FWDG_EN (1 << 6)
+#define CORE_DIS_LEARN 0x000f0
+
#define CORE_SFT_LRN_CTRL 0x000f8
#define SW_LEARN_CNTL(x) (1 << (x))
--
2.25.1
Standalone ports should not have learning enabled since all the frames
are always copied to the CPU port. This is particularly important in
case an user-facing port intentionally spoofs the CPU port's MAC
address. With learning enabled we would end up with the switch having
incorrectly learned the address of the CPU port which typically results
in a complete break down of network connectivity until the address
learned ages out and gets re-learned, from the correct port this time.
There was no control of the BR_LEARNING flag until upstream commit
4098ced4680a485c5953f60ac63dff19f3fb3d42 ("Merge branch 'brport-flags'")
which is why we default to enabling learning when the ports gets added
as a bridge member.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 20 ++++++++++++++++++++
drivers/net/dsa/b53/b53_regs.h | 1 +
drivers/net/dsa/bcm_sf2.c | 5 +++++
drivers/net/dsa/bcm_sf2_regs.h | 2 ++
4 files changed, 28 insertions(+)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index c17cdbd0bb6a..820aed3e2352 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -501,6 +501,19 @@ static void b53_imp_vlan_setup(struct dsa_switch *ds, int cpu_port)
}
}
+static void b53_port_set_learning(struct b53_device *dev, int port,
+ bool learning)
+{
+ u16 reg;
+
+ b53_read16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, ®);
+ if (learning)
+ reg &= ~BIT(port);
+ else
+ reg |= BIT(port);
+ b53_write16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, reg);
+}
+
static int b53_enable_port(struct dsa_switch *ds, int port,
struct phy_device *phy)
{
@@ -508,6 +521,8 @@ static int b53_enable_port(struct dsa_switch *ds, int port,
unsigned int cpu_port = dev->cpu_port;
u16 pvlan;
+ b53_port_set_learning(dev, port, false);
+
/* Clear the Rx and Tx disable bits and set to no spanning tree */
b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(port), 0);
@@ -551,6 +566,8 @@ static void b53_enable_cpu_port(struct b53_device *dev)
PORT_CTRL_RX_MCST_EN |
PORT_CTRL_RX_UCST_EN;
b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(cpu_port), port_ctrl);
+
+ b53_port_set_learning(dev, cpu_port, false);
}
static void b53_enable_mib(struct b53_device *dev)
@@ -1342,6 +1359,8 @@ int b53_br_join(struct dsa_switch *ds, int port, struct net_device *br)
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), pvlan);
dev->ports[port].vlan_ctl_mask = pvlan;
+ b53_port_set_learning(dev, port, true);
+
return 0;
}
EXPORT_SYMBOL(b53_br_join);
@@ -1392,6 +1411,7 @@ void b53_br_leave(struct dsa_switch *ds, int port, struct net_device *br)
vl->untag |= BIT(port) | BIT(dev->cpu_port);
b53_set_vlan_entry(dev, pvid, vl);
}
+ b53_port_set_learning(dev, port, false);
}
EXPORT_SYMBOL(b53_br_leave);
diff --git a/drivers/net/dsa/b53/b53_regs.h b/drivers/net/dsa/b53/b53_regs.h
index 247aef92b759..2b892b8d0374 100644
--- a/drivers/net/dsa/b53/b53_regs.h
+++ b/drivers/net/dsa/b53/b53_regs.h
@@ -112,6 +112,7 @@
#define B53_UC_FLOOD_MASK 0x32
#define B53_MC_FLOOD_MASK 0x34
#define B53_IPMC_FLOOD_MASK 0x36
+#define B53_DIS_LEARNING 0x3c
/*
* Override Ports 0-7 State on devices with xMII interfaces (8 bit)
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 91c8405e515f..7fc84ae562a2 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -252,6 +252,11 @@ static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
+ /* Disable learning */
+ reg = core_readl(priv, CORE_DIS_LEARN);
+ reg |= BIT(port);
+ core_writel(priv, reg, CORE_DIS_LEARN);
+
/* Enable Broadcom tags for that port if requested */
if (priv->brcm_tag_mask & BIT(port))
bcm_sf2_brcm_hdr_setup(priv, port);
diff --git a/drivers/net/dsa/bcm_sf2_regs.h b/drivers/net/dsa/bcm_sf2_regs.h
index 49695fcc2ea8..da1336ddd52d 100644
--- a/drivers/net/dsa/bcm_sf2_regs.h
+++ b/drivers/net/dsa/bcm_sf2_regs.h
@@ -150,6 +150,8 @@ enum bcm_sf2_reg_offs {
#define CORE_SWITCH_CTRL 0x00088
#define MII_DUMB_FWDG_EN (1 << 6)
+#define CORE_DIS_LEARN 0x000f0
+
#define CORE_SFT_LRN_CTRL 0x000f8
#define SW_LEARN_CNTL(x) (1 << (x))
--
2.25.1
Standalone ports should not have learning enabled since all the frames
are always copied to the CPU port. This is particularly important in
case an user-facing port intentionally spoofs the CPU port's MAC
address. With learning enabled we would end up with the switch having
incorrectly learned the address of the CPU port which typically results
in a complete break down of network connectivity until the address
learned ages out and gets re-learned, from the correct port this time.
There was no control of the BR_LEARNING flag until upstream commit
4098ced4680a485c5953f60ac63dff19f3fb3d42 ("Merge branch 'brport-flags'")
which is why we default to enabling learning when the ports gets added
as a bridge member.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 19 +++++++++++++++++++
drivers/net/dsa/b53/b53_regs.h | 1 +
drivers/net/dsa/bcm_sf2.c | 5 -----
3 files changed, 20 insertions(+), 5 deletions(-)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index 335ce1e84904..7eaeab65d39f 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -507,12 +507,27 @@ void b53_imp_vlan_setup(struct dsa_switch *ds, int cpu_port)
}
EXPORT_SYMBOL(b53_imp_vlan_setup);
+static void b53_port_set_learning(struct b53_device *dev, int port,
+ bool learning)
+{
+ u16 reg;
+
+ b53_read16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, ®);
+ if (learning)
+ reg &= ~BIT(port);
+ else
+ reg |= BIT(port);
+ b53_write16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, reg);
+}
+
int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
{
struct b53_device *dev = ds->priv;
unsigned int cpu_port = ds->ports[port].cpu_dp->index;
u16 pvlan;
+ b53_port_set_learning(dev, port, false);
+
/* Clear the Rx and Tx disable bits and set to no spanning tree */
b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(port), 0);
@@ -620,6 +635,7 @@ static void b53_enable_cpu_port(struct b53_device *dev, int port)
b53_write8(dev, B53_CTRL_PAGE, B53_PORT_CTRL(port), port_ctrl);
b53_brcm_hdr_setup(dev->ds, port);
+ b53_port_set_learning(dev, port, false);
}
static void b53_enable_mib(struct b53_device *dev)
@@ -1517,6 +1533,8 @@ int b53_br_join(struct dsa_switch *ds, int port, struct net_device *br)
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), pvlan);
dev->ports[port].vlan_ctl_mask = pvlan;
+ b53_port_set_learning(dev, port, true);
+
return 0;
}
EXPORT_SYMBOL(b53_br_join);
@@ -1564,6 +1582,7 @@ void b53_br_leave(struct dsa_switch *ds, int port, struct net_device *br)
vl->untag |= BIT(port) | BIT(cpu_port);
b53_set_vlan_entry(dev, pvid, vl);
}
+ b53_port_set_learning(dev, port, false);
}
EXPORT_SYMBOL(b53_br_leave);
diff --git a/drivers/net/dsa/b53/b53_regs.h b/drivers/net/dsa/b53/b53_regs.h
index c90985c294a2..b2c539a42154 100644
--- a/drivers/net/dsa/b53/b53_regs.h
+++ b/drivers/net/dsa/b53/b53_regs.h
@@ -115,6 +115,7 @@
#define B53_UC_FLOOD_MASK 0x32
#define B53_MC_FLOOD_MASK 0x34
#define B53_IPMC_FLOOD_MASK 0x36
+#define B53_DIS_LEARNING 0x3c
/*
* Override Ports 0-7 State on devices with xMII interfaces (8 bit)
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 613f03f9d9ec..e9fe3897bd9c 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -173,11 +173,6 @@ static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
- /* Enable learning */
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg &= ~BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
-
/* Enable Broadcom tags for that port if requested */
if (priv->brcm_tag_mask & BIT(port))
b53_brcm_hdr_setup(ds, port);
--
2.25.1
Standalone ports should not have learning enabled since all the frames
are always copied to the CPU port. This is particularly important in
case an user-facing port intentionally spoofs the CPU port's MAC
address. With learning enabled we would end up with the switch having
incorrectly learned the address of the CPU port which typically results
in a complete break down of network connectivity until the address
learned ages out and gets re-learned, from the correct port this time.
There was no control of the BR_LEARNING flag until upstream commit
4098ced4680a485c5953f60ac63dff19f3fb3d42 ("Merge branch 'brport-flags'")
which is why we default to enabling learning when the ports gets added
as a bridge member.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 18 ++++++++++++++++++
drivers/net/dsa/b53/b53_regs.h | 1 +
drivers/net/dsa/bcm_sf2.c | 5 -----
3 files changed, 19 insertions(+), 5 deletions(-)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index 0b1223f360d9..f35757b63ea7 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -514,6 +514,19 @@ void b53_imp_vlan_setup(struct dsa_switch *ds, int cpu_port)
}
EXPORT_SYMBOL(b53_imp_vlan_setup);
+static void b53_port_set_learning(struct b53_device *dev, int port,
+ bool learning)
+{
+ u16 reg;
+
+ b53_read16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, ®);
+ if (learning)
+ reg &= ~BIT(port);
+ else
+ reg |= BIT(port);
+ b53_write16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, reg);
+}
+
int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
{
struct b53_device *dev = ds->priv;
@@ -527,6 +540,7 @@ int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
cpu_port = ds->ports[port].cpu_dp->index;
b53_br_egress_floods(ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
if (dev->ops->irq_enable)
ret = dev->ops->irq_enable(dev, port);
@@ -645,6 +659,7 @@ static void b53_enable_cpu_port(struct b53_device *dev, int port)
b53_brcm_hdr_setup(dev->ds, port);
b53_br_egress_floods(dev->ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
}
static void b53_enable_mib(struct b53_device *dev)
@@ -1704,6 +1719,8 @@ int b53_br_join(struct dsa_switch *ds, int port, struct net_device *br)
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), pvlan);
dev->ports[port].vlan_ctl_mask = pvlan;
+ b53_port_set_learning(dev, port, true);
+
return 0;
}
EXPORT_SYMBOL(b53_br_join);
@@ -1751,6 +1768,7 @@ void b53_br_leave(struct dsa_switch *ds, int port, struct net_device *br)
vl->untag |= BIT(port) | BIT(cpu_port);
b53_set_vlan_entry(dev, pvid, vl);
}
+ b53_port_set_learning(dev, port, false);
}
EXPORT_SYMBOL(b53_br_leave);
diff --git a/drivers/net/dsa/b53/b53_regs.h b/drivers/net/dsa/b53/b53_regs.h
index c90985c294a2..b2c539a42154 100644
--- a/drivers/net/dsa/b53/b53_regs.h
+++ b/drivers/net/dsa/b53/b53_regs.h
@@ -115,6 +115,7 @@
#define B53_UC_FLOOD_MASK 0x32
#define B53_MC_FLOOD_MASK 0x34
#define B53_IPMC_FLOOD_MASK 0x36
+#define B53_DIS_LEARNING 0x3c
/*
* Override Ports 0-7 State on devices with xMII interfaces (8 bit)
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 6dd29bad1609..ca425c15953b 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -172,11 +172,6 @@ static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
- /* Enable learning */
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg &= ~BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
-
/* Enable Broadcom tags for that port if requested */
if (priv->brcm_tag_mask & BIT(port))
b53_brcm_hdr_setup(ds, port);
--
2.25.1
Standalone ports should not have learning enabled since all the frames
are always copied to the CPU port. This is particularly important in
case an user-facing port intentionally spoofs the CPU port's MAC
address. With learning enabled we would end up with the switch having
incorrectly learned the address of the CPU port which typically results
in a complete break down of network connectivity until the address
learned ages out and gets re-learned, from the correct port this time.
There was no control of the BR_LEARNING flag until upstream commit
4098ced4680a485c5953f60ac63dff19f3fb3d42 ("Merge branch 'brport-flags'")
which is why we default to enabling learning when the ports gets added
as a bridge member.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 18 ++++++++++++++++++
drivers/net/dsa/b53/b53_regs.h | 1 +
drivers/net/dsa/bcm_sf2.c | 15 +--------------
3 files changed, 20 insertions(+), 14 deletions(-)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index 95c7fa171e35..f504b6858ed2 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -510,6 +510,19 @@ void b53_imp_vlan_setup(struct dsa_switch *ds, int cpu_port)
}
EXPORT_SYMBOL(b53_imp_vlan_setup);
+static void b53_port_set_learning(struct b53_device *dev, int port,
+ bool learning)
+{
+ u16 reg;
+
+ b53_read16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, ®);
+ if (learning)
+ reg &= ~BIT(port);
+ else
+ reg |= BIT(port);
+ b53_write16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, reg);
+}
+
int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
{
struct b53_device *dev = ds->priv;
@@ -523,6 +536,7 @@ int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
b53_br_egress_floods(ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
if (dev->ops->irq_enable)
ret = dev->ops->irq_enable(dev, port);
@@ -656,6 +670,7 @@ static void b53_enable_cpu_port(struct b53_device *dev, int port)
b53_brcm_hdr_setup(dev->ds, port);
b53_br_egress_floods(dev->ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
}
static void b53_enable_mib(struct b53_device *dev)
@@ -1839,6 +1854,8 @@ int b53_br_join(struct dsa_switch *ds, int port, struct net_device *br)
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), pvlan);
dev->ports[port].vlan_ctl_mask = pvlan;
+ b53_port_set_learning(dev, port, true);
+
return 0;
}
EXPORT_SYMBOL(b53_br_join);
@@ -1886,6 +1903,7 @@ void b53_br_leave(struct dsa_switch *ds, int port, struct net_device *br)
vl->untag |= BIT(port) | BIT(cpu_port);
b53_set_vlan_entry(dev, pvid, vl);
}
+ b53_port_set_learning(dev, port, false);
}
EXPORT_SYMBOL(b53_br_leave);
diff --git a/drivers/net/dsa/b53/b53_regs.h b/drivers/net/dsa/b53/b53_regs.h
index c90985c294a2..b2c539a42154 100644
--- a/drivers/net/dsa/b53/b53_regs.h
+++ b/drivers/net/dsa/b53/b53_regs.h
@@ -115,6 +115,7 @@
#define B53_UC_FLOOD_MASK 0x32
#define B53_MC_FLOOD_MASK 0x34
#define B53_IPMC_FLOOD_MASK 0x36
+#define B53_DIS_LEARNING 0x3c
/*
* Override Ports 0-7 State on devices with xMII interfaces (8 bit)
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 445226720ff2..edb0a1027b38 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -222,23 +222,10 @@ static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
- /* Enable learning */
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg &= ~BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
-
/* Enable Broadcom tags for that port if requested */
- if (priv->brcm_tag_mask & BIT(port)) {
+ if (priv->brcm_tag_mask & BIT(port))
b53_brcm_hdr_setup(ds, port);
- /* Disable learning on ASP port */
- if (port == 7) {
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg |= BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
- }
- }
-
/* Configure Traffic Class to QoS mapping, allow each priority to map
* to a different queue number
*/
--
2.25.1
Standalone ports should not have learning enabled since all the frames
are always copied to the CPU port. This is particularly important in
case an user-facing port intentionally spoofs the CPU port's MAC
address. With learning enabled we would end up with the switch having
incorrectly learned the address of the CPU port which typically results
in a complete break down of network connectivity until the address
learned ages out and gets re-learned, from the correct port this time.
There was no control of the BR_LEARNING flag until upstream commit
4098ced4680a485c5953f60ac63dff19f3fb3d42 ("Merge branch 'brport-flags'")
which is why we default to enabling learning when the ports gets added
as a bridge member.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 18 ++++++++++++++++++
drivers/net/dsa/b53/b53_regs.h | 1 +
drivers/net/dsa/bcm_sf2.c | 15 +--------------
3 files changed, 20 insertions(+), 14 deletions(-)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index 95c7fa171e35..f504b6858ed2 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -510,6 +510,19 @@ void b53_imp_vlan_setup(struct dsa_switch *ds, int cpu_port)
}
EXPORT_SYMBOL(b53_imp_vlan_setup);
+static void b53_port_set_learning(struct b53_device *dev, int port,
+ bool learning)
+{
+ u16 reg;
+
+ b53_read16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, ®);
+ if (learning)
+ reg &= ~BIT(port);
+ else
+ reg |= BIT(port);
+ b53_write16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, reg);
+}
+
int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
{
struct b53_device *dev = ds->priv;
@@ -523,6 +536,7 @@ int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
b53_br_egress_floods(ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
if (dev->ops->irq_enable)
ret = dev->ops->irq_enable(dev, port);
@@ -656,6 +670,7 @@ static void b53_enable_cpu_port(struct b53_device *dev, int port)
b53_brcm_hdr_setup(dev->ds, port);
b53_br_egress_floods(dev->ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
}
static void b53_enable_mib(struct b53_device *dev)
@@ -1839,6 +1854,8 @@ int b53_br_join(struct dsa_switch *ds, int port, struct net_device *br)
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), pvlan);
dev->ports[port].vlan_ctl_mask = pvlan;
+ b53_port_set_learning(dev, port, true);
+
return 0;
}
EXPORT_SYMBOL(b53_br_join);
@@ -1886,6 +1903,7 @@ void b53_br_leave(struct dsa_switch *ds, int port, struct net_device *br)
vl->untag |= BIT(port) | BIT(cpu_port);
b53_set_vlan_entry(dev, pvid, vl);
}
+ b53_port_set_learning(dev, port, false);
}
EXPORT_SYMBOL(b53_br_leave);
diff --git a/drivers/net/dsa/b53/b53_regs.h b/drivers/net/dsa/b53/b53_regs.h
index c90985c294a2..b2c539a42154 100644
--- a/drivers/net/dsa/b53/b53_regs.h
+++ b/drivers/net/dsa/b53/b53_regs.h
@@ -115,6 +115,7 @@
#define B53_UC_FLOOD_MASK 0x32
#define B53_MC_FLOOD_MASK 0x34
#define B53_IPMC_FLOOD_MASK 0x36
+#define B53_DIS_LEARNING 0x3c
/*
* Override Ports 0-7 State on devices with xMII interfaces (8 bit)
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 445226720ff2..edb0a1027b38 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -222,23 +222,10 @@ static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
- /* Enable learning */
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg &= ~BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
-
/* Enable Broadcom tags for that port if requested */
- if (priv->brcm_tag_mask & BIT(port)) {
+ if (priv->brcm_tag_mask & BIT(port))
b53_brcm_hdr_setup(ds, port);
- /* Disable learning on ASP port */
- if (port == 7) {
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg |= BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
- }
- }
-
/* Configure Traffic Class to QoS mapping, allow each priority to map
* to a different queue number
*/
--
2.25.1
Standalone ports should not have learning enabled since all the frames
are always copied to the CPU port. This is particularly important in
case an user-facing port intentionally spoofs the CPU port's MAC
address. With learning enabled we would end up with the switch having
incorrectly learned the address of the CPU port which typically results
in a complete break down of network connectivity until the address
learned ages out and gets re-learned, from the correct port this time.
There was no control of the BR_LEARNING flag until upstream commit
4098ced4680a485c5953f60ac63dff19f3fb3d42 ("Merge branch 'brport-flags'")
which is why we default to enabling learning when the ports gets added
as a bridge member.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 18 ++++++++++++++++++
drivers/net/dsa/b53/b53_regs.h | 1 +
drivers/net/dsa/bcm_sf2.c | 15 +--------------
3 files changed, 20 insertions(+), 14 deletions(-)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index 86869337223a..5559dec0fbca 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -512,6 +512,19 @@ void b53_imp_vlan_setup(struct dsa_switch *ds, int cpu_port)
}
EXPORT_SYMBOL(b53_imp_vlan_setup);
+static void b53_port_set_learning(struct b53_device *dev, int port,
+ bool learning)
+{
+ u16 reg;
+
+ b53_read16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, ®);
+ if (learning)
+ reg &= ~BIT(port);
+ else
+ reg |= BIT(port);
+ b53_write16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, reg);
+}
+
int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
{
struct b53_device *dev = ds->priv;
@@ -525,6 +538,7 @@ int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
b53_br_egress_floods(ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
if (dev->ops->irq_enable)
ret = dev->ops->irq_enable(dev, port);
@@ -658,6 +672,7 @@ static void b53_enable_cpu_port(struct b53_device *dev, int port)
b53_brcm_hdr_setup(dev->ds, port);
b53_br_egress_floods(dev->ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
}
static void b53_enable_mib(struct b53_device *dev)
@@ -1797,6 +1812,8 @@ int b53_br_join(struct dsa_switch *ds, int port, struct net_device *br)
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), pvlan);
dev->ports[port].vlan_ctl_mask = pvlan;
+ b53_port_set_learning(dev, port, true);
+
return 0;
}
EXPORT_SYMBOL(b53_br_join);
@@ -1844,6 +1861,7 @@ void b53_br_leave(struct dsa_switch *ds, int port, struct net_device *br)
vl->untag |= BIT(port) | BIT(cpu_port);
b53_set_vlan_entry(dev, pvid, vl);
}
+ b53_port_set_learning(dev, port, false);
}
EXPORT_SYMBOL(b53_br_leave);
diff --git a/drivers/net/dsa/b53/b53_regs.h b/drivers/net/dsa/b53/b53_regs.h
index c90985c294a2..b2c539a42154 100644
--- a/drivers/net/dsa/b53/b53_regs.h
+++ b/drivers/net/dsa/b53/b53_regs.h
@@ -115,6 +115,7 @@
#define B53_UC_FLOOD_MASK 0x32
#define B53_MC_FLOOD_MASK 0x34
#define B53_IPMC_FLOOD_MASK 0x36
+#define B53_DIS_LEARNING 0x3c
/*
* Override Ports 0-7 State on devices with xMII interfaces (8 bit)
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 946e41f020a5..4d8f0c9c4d97 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -172,23 +172,10 @@ static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
- /* Enable learning */
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg &= ~BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
-
/* Enable Broadcom tags for that port if requested */
- if (priv->brcm_tag_mask & BIT(port)) {
+ if (priv->brcm_tag_mask & BIT(port))
b53_brcm_hdr_setup(ds, port);
- /* Disable learning on ASP port */
- if (port == 7) {
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg |= BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
- }
- }
-
/* Configure Traffic Class to QoS mapping, allow each priority to map
* to a different queue number
*/
--
2.25.1
Standalone ports should not have learning enabled since all the frames
are always copied to the CPU port. This is particularly important in
case an user-facing port intentionally spoofs the CPU port's MAC
address. With learning enabled we would end up with the switch having
incorrectly learned the address of the CPU port which typically results
in a complete break down of network connectivity until the address
learned ages out and gets re-learned, from the correct port this time.
There was no control of the BR_LEARNING flag until upstream commit
4098ced4680a485c5953f60ac63dff19f3fb3d42 ("Merge branch 'brport-flags'")
which is why we default to enabling learning when the ports gets added
as a bridge member.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <[email protected]>
---
drivers/net/dsa/b53/b53_common.c | 18 ++++++++++++++++++
drivers/net/dsa/b53/b53_regs.h | 1 +
drivers/net/dsa/bcm_sf2.c | 15 +--------------
3 files changed, 20 insertions(+), 14 deletions(-)
diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index e731db900ee0..23dbb91946a7 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -512,6 +512,19 @@ void b53_imp_vlan_setup(struct dsa_switch *ds, int cpu_port)
}
EXPORT_SYMBOL(b53_imp_vlan_setup);
+static void b53_port_set_learning(struct b53_device *dev, int port,
+ bool learning)
+{
+ u16 reg;
+
+ b53_read16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, ®);
+ if (learning)
+ reg &= ~BIT(port);
+ else
+ reg |= BIT(port);
+ b53_write16(dev, B53_CTRL_PAGE, B53_DIS_LEARNING, reg);
+}
+
int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
{
struct b53_device *dev = ds->priv;
@@ -525,6 +538,7 @@ int b53_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
b53_br_egress_floods(ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
if (dev->ops->irq_enable)
ret = dev->ops->irq_enable(dev, port);
@@ -658,6 +672,7 @@ static void b53_enable_cpu_port(struct b53_device *dev, int port)
b53_brcm_hdr_setup(dev->ds, port);
b53_br_egress_floods(dev->ds, port, true, true);
+ b53_port_set_learning(dev, port, false);
}
static void b53_enable_mib(struct b53_device *dev)
@@ -1796,6 +1811,8 @@ int b53_br_join(struct dsa_switch *ds, int port, struct net_device *br)
b53_write16(dev, B53_PVLAN_PAGE, B53_PVLAN_PORT_MASK(port), pvlan);
dev->ports[port].vlan_ctl_mask = pvlan;
+ b53_port_set_learning(dev, port, true);
+
return 0;
}
EXPORT_SYMBOL(b53_br_join);
@@ -1843,6 +1860,7 @@ void b53_br_leave(struct dsa_switch *ds, int port, struct net_device *br)
vl->untag |= BIT(port) | BIT(cpu_port);
b53_set_vlan_entry(dev, pvid, vl);
}
+ b53_port_set_learning(dev, port, false);
}
EXPORT_SYMBOL(b53_br_leave);
diff --git a/drivers/net/dsa/b53/b53_regs.h b/drivers/net/dsa/b53/b53_regs.h
index c90985c294a2..b2c539a42154 100644
--- a/drivers/net/dsa/b53/b53_regs.h
+++ b/drivers/net/dsa/b53/b53_regs.h
@@ -115,6 +115,7 @@
#define B53_UC_FLOOD_MASK 0x32
#define B53_MC_FLOOD_MASK 0x34
#define B53_IPMC_FLOOD_MASK 0x36
+#define B53_DIS_LEARNING 0x3c
/*
* Override Ports 0-7 State on devices with xMII interfaces (8 bit)
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 5ebff986a1ac..99402f769584 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -172,23 +172,10 @@ static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
- /* Enable learning */
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg &= ~BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
-
/* Enable Broadcom tags for that port if requested */
- if (priv->brcm_tag_mask & BIT(port)) {
+ if (priv->brcm_tag_mask & BIT(port))
b53_brcm_hdr_setup(ds, port);
- /* Disable learning on ASP port */
- if (port == 7) {
- reg = core_readl(priv, CORE_DIS_LEARN);
- reg |= BIT(port);
- core_writel(priv, reg, CORE_DIS_LEARN);
- }
- }
-
/* Configure Traffic Class to QoS mapping, allow each priority to map
* to a different queue number
*/
--
2.25.1
On Wed, Feb 24, 2021 at 05:09:54PM -0800, Florian Fainelli wrote:
> Standalone ports should not have learning enabled since all the frames
> are always copied to the CPU port. This is particularly important in
> case an user-facing port intentionally spoofs the CPU port's MAC
> address. With learning enabled we would end up with the switch having
> incorrectly learned the address of the CPU port which typically results
> in a complete break down of network connectivity until the address
> learned ages out and gets re-learned, from the correct port this time.
>
> There was no control of the BR_LEARNING flag until upstream commit
> 4098ced4680a485c5953f60ac63dff19f3fb3d42 ("Merge branch 'brport-flags'")
> which is why we default to enabling learning when the ports gets added
> as a bridge member.
>
> Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
> Signed-off-by: Florian Fainelli <[email protected]>
> ---
> drivers/net/dsa/b53/b53_common.c | 18 ++++++++++++++++++
> drivers/net/dsa/b53/b53_regs.h | 1 +
> drivers/net/dsa/bcm_sf2.c | 15 +--------------
> 3 files changed, 20 insertions(+), 14 deletions(-)
Note, 5.9.y and 5.8.y are long end-of-life. You can see that at the
front page of http://www.kernel.org if you ever are curious about it.
thanks,
greg k-h