Based on linux-gpio discussion [1], it is best practice to make the
gpio-line-names unique. Generic names like "[ethernet]" are replaced
with the name of the unique signal on the AM3358 SoC ball corresponding
to the gpio line. "[NC]" is also renamed to the standard "NC" name to
represent "not connected".
[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/
Signed-off-by: Drew Fustini <[email protected]>
---
Tony - I have fixed the conflict so this now applies against mainline.
arch/arm/boot/dts/am335x-boneblack.dts | 132 ++++++++++++-------------
1 file changed, 66 insertions(+), 66 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index b4feb85e171a..e2ee8b8c07bc 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -26,54 +26,54 @@ oppnitro-1000000000 {
&gpio0 {
gpio-line-names =
- "[ethernet]",
- "[ethernet]",
+ "[mdio_data]",
+ "[mdio_clk]",
"P9_22 [spi0_sclk]",
"P9_21 [spi0_d0]",
"P9_18 [spi0_d1]",
"P9_17 [spi0_cs0]",
- "[sd card]",
- "P9_42A [ecappwm0]",
- "P8_35 [hdmi]",
- "P8_33 [hdmi]",
- "P8_31 [hdmi]",
- "P8_32 [hdmi]",
+ "[mmc0_cd]",
+ "P8_42A [ecappwm0]",
+ "P8_35 [lcd d12]",
+ "P8_33 [lcd d13]",
+ "P8_31 [lcd d14]",
+ "P8_32 [lcd d15]",
"P9_20 [i2c2_sda]",
"P9_19 [i2c2_scl]",
"P9_26 [uart1_rxd]",
"P9_24 [uart1_txd]",
- "[ethernet]",
- "[ethernet]",
- "[usb]",
- "[hdmi]",
+ "[rmii1_txd3]",
+ "[rmii1_txd2]",
+ "[usb0_drvvbus]",
+ "[hdmi cec]",
"P9_41B",
- "[ethernet]",
+ "[rmii1_txd1]",
"P8_19 [ehrpwm2a]",
"P8_13 [ehrpwm2b]",
- "[NC]",
- "[NC]",
+ "NC",
+ "NC",
"P8_14",
"P8_17",
- "[ethernet]",
- "[ethernet]",
+ "[rmii1_txd0]",
+ "[rmii1_refclk]",
"P9_11 [uart4_rxd]",
"P9_13 [uart4_txd]";
};
&gpio1 {
gpio-line-names =
- "P8_25 [emmc]",
- "[emmc]",
- "P8_5 [emmc]",
- "P8_6 [emmc]",
- "P8_23 [emmc]",
- "P8_22 [emmc]",
- "P8_3 [emmc]",
- "P8_4 [emmc]",
- "[NC]",
- "[NC]",
- "[NC]",
- "[NC]",
+ "P8_25 [mmc1_dat0]",
+ "[mmc1_dat1]",
+ "P8_5 [mmc1_dat2]",
+ "P8_6 [mmc1_dat3]",
+ "P8_23 [mmc1_dat4]",
+ "P8_22 [mmc1_dat5]",
+ "P8_3 [mmc1_dat6]",
+ "P8_4 [mmc1_dat7]",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
"P8_12",
"P8_11",
"P8_16",
@@ -82,13 +82,13 @@ &gpio1 {
"P9_23",
"P9_14 [ehrpwm1a]",
"P9_16 [ehrpwm1b]",
- "[emmc]",
+ "[emmc rst]",
"[usr0 led]",
"[usr1 led]",
"[usr2 led]",
"[usr3 led]",
- "[hdmi]",
- "[usb]",
+ "[hdmi irq]",
+ "[usb vbus oc]",
"[hdmi audio]",
"P9_12",
"P8_26",
@@ -116,38 +116,38 @@ &gpio2 {
"P8_38 [hdmi]",
"P8_36 [hdmi]",
"P8_34 [hdmi]",
- "[ethernet]",
- "[ethernet]",
- "[ethernet]",
- "[ethernet]",
+ "[rmii1_rxd3]",
+ "[rmii1_rxd2]",
+ "[rmii1_rxd1]",
+ "[rmii1_rxd0]",
"P8_27 [hdmi]",
"P8_29 [hdmi]",
"P8_28 [hdmi]",
"P8_30 [hdmi]",
- "[emmc]",
- "[emmc]",
- "[emmc]",
- "[emmc]",
- "[emmc]",
- "[emmc]";
+ "[mmc0_dat3]",
+ "[mmc0_dat2]",
+ "[mmc0_dat1]",
+ "[mmc0_dat0]",
+ "[mmc0_clk]",
+ "[mmc0_cmd]";
};
&gpio3 {
gpio-line-names =
- "[ethernet]",
- "[ethernet]",
- "[ethernet]",
- "[ethernet]",
- "[ethernet]",
- "[i2c0]",
- "[i2c0]",
- "[emu]",
- "[emu]",
- "[ethernet]",
- "[ethernet]",
- "[NC]",
- "[NC]",
- "[usb]",
+ "[mii col]",
+ "[mii crs]",
+ "[mii rx err]",
+ "[mii tx en]",
+ "[mii rx dv]",
+ "[i2c0 sda]",
+ "[i2c0 scl]",
+ "[jtag emu0]",
+ "[jtag emu1]",
+ "[mii tx clk]",
+ "[mii rx clk]",
+ "NC",
+ "NC",
+ "[usb vbus en]",
"P9_31 [spi1_sclk]",
"P9_29 [spi1_d0]",
"P9_30 [spi1_d1]",
@@ -156,14 +156,14 @@ &gpio3 {
"P9_27",
"P9_41A",
"P9_25",
- "[NC]",
- "[NC]",
- "[NC]",
- "[NC]",
- "[NC]",
- "[NC]",
- "[NC]",
- "[NC]",
- "[NC]",
- "[NC]";
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC";
};
--
2.27.0
* Drew Fustini <[email protected]> [210325 00:25]:
> Based on linux-gpio discussion [1], it is best practice to make the
> gpio-line-names unique. Generic names like "[ethernet]" are replaced
> with the name of the unique signal on the AM3358 SoC ball corresponding
> to the gpio line. "[NC]" is also renamed to the standard "NC" name to
> represent "not connected".
Thanks applying into omap-for-v5.13/dt-v2.
Tony