Hello,
This series adds support for Qualcomm PCIe Endpoint controller found
in platforms like SDX55. The Endpoint controller is based on the designware
core with additional Qualcomm wrappers around the core.
The driver is added separately unlike other Designware based drivers that
combine RC and EP in a single driver. This is done to avoid complexity and
to maintain this driver autonomously.
The driver has been validated with an out of tree MHI function driver on
SDX55 based Telit FN980 EVB connected to x86 host machine over PCIe.
Thanks,
Mani
Changes in v6:
* Removed status property in DT and added reviewed tag from Rob
* Switched to _relaxed variants as suggested by Rob
Changes in v5:
* Removed the DBI register settings that are not needed
* Used the standard definitions available in pci_regs.h
* Added defines for all the register fields
* Removed the left over code from previous iteration
Changes in v4:
* Removed the active_config settings needed for IPA integration
* Switched to writel for couple of relaxed versions that sneaked in
Changes in v3:
* Lot of minor cleanups to the driver patch based on review from Bjorn and Stan.
* Noticeable changes are:
- Got rid of _relaxed calls and used readl/writel
- Got rid of separate TCSR memory region and used syscon for getting the
register offsets for Perst registers
- Changed the wake gpio handling logic
- Added remove() callback and removed "suppress_bind_attrs"
- stop_link() callback now just disables PERST IRQ
* Added MMIO region and doorbell interrupt to the binding
* Added logic to write MMIO physicall address to MHI base address as it is
for the function driver to work
Changes in v2:
* Addressed the comments from Rob on bindings patch
* Modified the driver as per binding change
* Fixed the warnings reported by Kbuild bot
* Removed the PERST# "enable_irq" call from probe()
Manivannan Sadhasivam (3):
dt-bindings: pci: Add devicetree binding for Qualcomm PCIe EP
controller
PCI: dwc: Add Qualcomm PCIe Endpoint controller driver
MAINTAINERS: Add entry for Qualcomm PCIe Endpoint driver and binding
.../devicetree/bindings/pci/qcom,pcie-ep.yaml | 158 ++++
MAINTAINERS | 10 +-
drivers/pci/controller/dwc/Kconfig | 10 +
drivers/pci/controller/dwc/Makefile | 1 +
drivers/pci/controller/dwc/pcie-qcom-ep.c | 742 ++++++++++++++++++
5 files changed, 920 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
create mode 100644 drivers/pci/controller/dwc/pcie-qcom-ep.c
--
2.25.1
Add MAINTAINERS entry for Qualcomm PCIe Endpoint driver and its
devicetree binding. While at it, let's also fix the PCIE RC entry to
cover only the RC driver.
Signed-off-by: Manivannan Sadhasivam <[email protected]>
---
MAINTAINERS | 10 +++++++++-
1 file changed, 9 insertions(+), 1 deletion(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index bd7aff0c120f..cdd370138b9f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14254,7 +14254,15 @@ M: Stanimir Varbanov <[email protected]>
L: [email protected]
L: [email protected]
S: Maintained
-F: drivers/pci/controller/dwc/*qcom*
+F: drivers/pci/controller/dwc/pcie-qcom.c
+
+PCIE ENDPOINT DRIVER FOR QUALCOMM
+M: Manivannan Sadhasivam <[email protected]>
+L: [email protected]
+L: [email protected]
+S: Maintained
+F: Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
+F: drivers/pci/controller/dwc/pcie-qcom-ep.c
PCIE DRIVER FOR ROCKCHIP
M: Shawn Lin <[email protected]>
--
2.25.1