This is a limited workaround for the PWM IP issue.
Root cause:
When the SAR FIFO is empty, the new write value will be directly applied
to SAR even the current period is not over.
If the new SAR value is less than the old one, and the counter is
greater than the new SAR value, the current period will not filp the
level. This will result in a pulse with a duty cycle of 100%.
Workaround:
Add an old value SAR write before updating the new duty cycle to SAR.
This will keep the new value is always in a not empty fifo, and can be wait
to update after a period finished.
Limitation:
This workaround can only solve this issue when the PWM period is longer than
2us(or <500KHz).
Reviewed-by: Jun Li <[email protected]>
Signed-off-by: Clark Wang <[email protected]>
---
drivers/pwm/pwm-imx27.c | 67 ++++++++++++++++++++++++++++++++++++++---
1 file changed, 62 insertions(+), 5 deletions(-)
diff --git a/drivers/pwm/pwm-imx27.c b/drivers/pwm/pwm-imx27.c
index ea91a2f81a9f..bd97382622dd 100644
--- a/drivers/pwm/pwm-imx27.c
+++ b/drivers/pwm/pwm-imx27.c
@@ -21,11 +21,13 @@
#include <linux/platform_device.h>
#include <linux/pwm.h>
#include <linux/slab.h>
+#include <linux/spinlock.h>
#define MX3_PWMCR 0x00 /* PWM Control Register */
#define MX3_PWMSR 0x04 /* PWM Status Register */
#define MX3_PWMSAR 0x0C /* PWM Sample Register */
#define MX3_PWMPR 0x10 /* PWM Period Register */
+#define MX3_PWMCNR 0x14 /* PWM Counter Register */
#define MX3_PWMCR_FWM GENMASK(27, 26)
#define MX3_PWMCR_STOPEN BIT(25)
@@ -91,6 +93,7 @@ struct pwm_imx27_chip {
* value to return in that case.
*/
unsigned int duty_cycle;
+ spinlock_t lock;
};
#define to_pwm_imx27_chip(chip) container_of(chip, struct pwm_imx27_chip, chip)
@@ -201,10 +204,10 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
sr = readl(imx->mmio_base + MX3_PWMSR);
fifoav = FIELD_GET(MX3_PWMSR_FIFOAV, sr);
- if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+ if (fifoav >= MX3_PWMSR_FIFOAV_3WORDS) {
period_ms = DIV_ROUND_UP_ULL(pwm_get_period(pwm),
NSEC_PER_MSEC);
- msleep(period_ms);
+ msleep(period_ms * (fifoav - 2));
sr = readl(imx->mmio_base + MX3_PWMSR);
if (fifoav == FIELD_GET(MX3_PWMSR_FIFOAV, sr))
@@ -215,13 +218,15 @@ static void pwm_imx27_wait_fifo_slot(struct pwm_chip *chip,
static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
const struct pwm_state *state)
{
- unsigned long period_cycles, duty_cycles, prescale;
+ unsigned long period_cycles, duty_cycles, prescale, counter_check, flags;
struct pwm_imx27_chip *imx = to_pwm_imx27_chip(chip);
+ void __iomem *reg_sar = imx->mmio_base + MX3_PWMSAR;
+ __force u32 sar_last, sar_current;
struct pwm_state cstate;
unsigned long long c;
unsigned long long clkrate;
int ret;
- u32 cr;
+ u32 cr, timeout = 1000;
pwm_get_state(pwm, &cstate);
@@ -262,7 +267,57 @@ static int pwm_imx27_apply(struct pwm_chip *chip, struct pwm_device *pwm,
pwm_imx27_sw_reset(chip);
}
- writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+ /*
+ * This is a limited workaround. When the SAR FIFO is empty, the new
+ * write value will be directly applied to SAR even the current period
+ * is not over.
+ * If the new SAR value is less than the old one, and the counter is
+ * greater than the new SAR value, the current period will not filp
+ * the level. This will result in a pulse with a duty cycle of 100%.
+ * So, writing the current value of the SAR to SAR here before updating
+ * the new SAR value can avoid this issue.
+ *
+ * Add a spin lock and turn off the interrupt to ensure that the
+ * real-time performance can be guaranteed as much as possible when
+ * operating the following operations.
+ *
+ * 1. Add a threshold of 1.5us. If the time T between the read current
+ * count value CNR and the end of the cycle is less than 1.5us, wait
+ * for T to be longer than 1.5us before updating the SAR register.
+ * This is to avoid the situation that when the first SAR is written,
+ * the current cycle just ends and the SAR FIFO that just be written
+ * is emptied again.
+ *
+ * 2. Use __raw_writel() to minimize the interval between two writes to
+ * the SAR register to increase the fastest pwm frequency supported.
+ *
+ * When the PWM period is longer than 2us(or <500KHz), this workaround
+ * can solve this problem.
+ */
+ if (duty_cycles < imx->duty_cycle) {
+ c = clkrate * 1500;
+ do_div(c, NSEC_PER_SEC);
+ counter_check = c;
+ sar_last = cpu_to_le32(imx->duty_cycle);
+ sar_current = cpu_to_le32(duty_cycles);
+
+ spin_lock_irqsave(&imx->lock, flags);
+ if (state->period >= 2000) {
+ while ((period_cycles -
+ readl_relaxed(imx->mmio_base + MX3_PWMCNR))
+ < counter_check) {
+ if (!--timeout)
+ break;
+ };
+ }
+ if (!(MX3_PWMSR_FIFOAV &
+ readl_relaxed(imx->mmio_base + MX3_PWMSR)))
+ __raw_writel(sar_last, reg_sar);
+ __raw_writel(sar_current, reg_sar);
+ spin_unlock_irqrestore(&imx->lock, flags);
+ } else
+ writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+
writel(period_cycles, imx->mmio_base + MX3_PWMPR);
/*
@@ -323,6 +378,8 @@ static int pwm_imx27_probe(struct platform_device *pdev)
return dev_err_probe(&pdev->dev, PTR_ERR(imx->clk_per),
"failed to get peripheral clock\n");
+ spin_lock_init(&imx->lock);
+ imx->duty_cycle = 0;
imx->chip.ops = &pwm_imx27_ops;
imx->chip.dev = &pdev->dev;
imx->chip.npwm = 1;
--
2.25.1