Hello, this is a set of patches to allow the upstreaming of the
NV3052C panel found in the Anbernic RG350M mips gaming handheld.
It was never upstreamed so far due to a longstanding graphical
bug, which I propose to solve by introducing ingenic_drm_bridge_atomic_enable
in the drm driver so the CRTC can be enabled after the panel itself slept
out, and not before as it used to.
After the drm change, 2 of the existing panels have to be modified accordingly
to introduce missing .enable and .disable in their code.
Christophe Branchereau (3):
drm/ingenic : add ingenic_drm_bridge_atomic_enable
drm/panel: Add panel driver for NewVision NV3052C based LCDs
drm/panel : innolux-ej030na and abt-y030xx067a : add .enable and
.disable
drivers/gpu/drm/ingenic/ingenic-drm-drv.c | 19 +-
drivers/gpu/drm/panel/Kconfig | 9 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-abt-y030xx067a.c | 23 +-
drivers/gpu/drm/panel/panel-innolux-ej030na.c | 31 +-
.../gpu/drm/panel/panel-newvision-nv3052c.c | 504 ++++++++++++++++++
6 files changed, 575 insertions(+), 12 deletions(-)
create mode 100644 drivers/gpu/drm/panel/panel-newvision-nv3052c.c
--
2.34.1
Following the introduction of bridge_atomic_enable in the ingenic
drm driver, the crtc is enabled between .prepare and .enable, if
it exists.
Add it so the backlight is only enabled after the crtc is, to avoid
graphical issues.
Signed-off-by: Christophe Branchereau <[email protected]>
---
drivers/gpu/drm/panel/panel-abt-y030xx067a.c | 23 ++++++++++++--
drivers/gpu/drm/panel/panel-innolux-ej030na.c | 31 ++++++++++++++++---
2 files changed, 48 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
index f043b484055b..b5736344e3ec 100644
--- a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
+++ b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
@@ -183,8 +183,6 @@ static int y030xx067a_prepare(struct drm_panel *panel)
goto err_disable_regulator;
}
- msleep(120);
-
return 0;
err_disable_regulator:
@@ -202,6 +200,25 @@ static int y030xx067a_unprepare(struct drm_panel *panel)
return 0;
}
+static int y030xx067a_enable(struct drm_panel *panel)
+{
+ if (panel->backlight) {
+ /* Wait for the picture to be ready before enabling backlight */
+ msleep(120);
+ }
+
+ return 0;
+}
+
+static int y030xx067a_disable(struct drm_panel *panel)
+{
+ struct y030xx067a *priv = to_y030xx067a(panel);
+
+ regmap_clear_bits(priv->map, 0x06, REG06_XPSAVE);
+
+ return 0;
+}
+
static int y030xx067a_get_modes(struct drm_panel *panel,
struct drm_connector *connector)
{
@@ -239,6 +256,8 @@ static int y030xx067a_get_modes(struct drm_panel *panel,
static const struct drm_panel_funcs y030xx067a_funcs = {
.prepare = y030xx067a_prepare,
.unprepare = y030xx067a_unprepare,
+ .enable = y030xx067a_enable,
+ .disable = y030xx067a_disable,
.get_modes = y030xx067a_get_modes,
};
diff --git a/drivers/gpu/drm/panel/panel-innolux-ej030na.c b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
index c558de3f99be..6de7370185cd 100644
--- a/drivers/gpu/drm/panel/panel-innolux-ej030na.c
+++ b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
@@ -80,8 +80,6 @@ static const struct reg_sequence ej030na_init_sequence[] = {
{ 0x47, 0x08 },
{ 0x48, 0x0f },
{ 0x49, 0x0f },
-
- { 0x2b, 0x01 },
};
static int ej030na_prepare(struct drm_panel *panel)
@@ -109,8 +107,6 @@ static int ej030na_prepare(struct drm_panel *panel)
goto err_disable_regulator;
}
- msleep(120);
-
return 0;
err_disable_regulator:
@@ -128,6 +124,31 @@ static int ej030na_unprepare(struct drm_panel *panel)
return 0;
}
+static int ej030na_enable(struct drm_panel *panel)
+{
+ struct ej030na *priv = to_ej030na(panel);
+
+ /* standby off */
+ regmap_write(priv->map, 0x2b, 0x01);
+
+ if (panel->backlight) {
+ /* Wait for the picture to be ready before enabling backlight */
+ msleep(120);
+ }
+
+ return 0;
+}
+
+static int ej030na_disable(struct drm_panel *panel)
+{
+ struct ej030na *priv = to_ej030na(panel);
+
+ /* standby on */
+ regmap_write(priv->map, 0x2b, 0x00);
+
+ return 0;
+}
+
static int ej030na_get_modes(struct drm_panel *panel,
struct drm_connector *connector)
{
@@ -165,6 +186,8 @@ static int ej030na_get_modes(struct drm_panel *panel,
static const struct drm_panel_funcs ej030na_funcs = {
.prepare = ej030na_prepare,
.unprepare = ej030na_unprepare,
+ .enable = ej030na_enable,
+ .disable = ej030na_disable,
.get_modes = ej030na_get_modes,
};
--
2.34.1
This driver supports the NewVision NV3052C based LCDs. Right now, it
only supports the LeadTek LTK035C5444T 2.4" 640x480 TFT LCD panel, which
can be found in the Anbernic RG-350M handheld console.
Signed-off-by: Christophe Branchereau <[email protected]>
---
drivers/gpu/drm/panel/Kconfig | 9 +
drivers/gpu/drm/panel/Makefile | 1 +
.../gpu/drm/panel/panel-newvision-nv3052c.c | 504 ++++++++++++++++++
3 files changed, 514 insertions(+)
create mode 100644 drivers/gpu/drm/panel/panel-newvision-nv3052c.c
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index bb2e47229c68..40084f709789 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -283,6 +283,15 @@ config DRM_PANEL_NEC_NL8048HL11
panel (found on the Zoom2/3/3630 SDP boards). To compile this driver
as a module, choose M here.
+config DRM_PANEL_NEWVISION_NV3052C
+ tristate "NewVision NV3052C RGB/SPI panel"
+ depends on OF && SPI
+ depends on BACKLIGHT_CLASS_DEVICE
+ select DRM_MIPI_DBI
+ help
+ Say Y here if you want to enable support for the panels built
+ around the NewVision NV3052C display controller.
+
config DRM_PANEL_NOVATEK_NT35510
tristate "Novatek NT35510 RGB panel driver"
depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index 5740911f637c..42a7ab54234b 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK500HD1829) += panel-leadtek-ltk500hd1829.o
obj-$(CONFIG_DRM_PANEL_LG_LB035Q02) += panel-lg-lb035q02.o
obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
obj-$(CONFIG_DRM_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o
+obj-$(CONFIG_DRM_PANEL_NEWVISION_NV3052C) += panel-newvision-nv3052c.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35510) += panel-novatek-nt35510.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35560) += panel-novatek-nt35560.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35950) += panel-novatek-nt35950.o
diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3052c.c b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
new file mode 100644
index 000000000000..08a3b33bcce0
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
@@ -0,0 +1,504 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * NevVision NV3052C IPS LCD panel driver
+ *
+ * Copyright (C) 2020, Paul Cercueil <[email protected]>
+ * Copyright (C) 2022, Christophe Branchereau <[email protected]>
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/media-bus-format.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/drm_mipi_dbi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+struct nv3052c_panel_info {
+ const struct drm_display_mode *display_modes;
+ unsigned int num_modes;
+ u16 width_mm, height_mm;
+ u32 bus_format, bus_flags;
+};
+
+struct nv3052c {
+ struct device *dev;
+ struct drm_panel panel;
+ struct mipi_dbi dbi;
+
+ const struct nv3052c_panel_info *panel_info;
+
+ struct regulator *supply;
+ struct gpio_desc *reset_gpio;
+};
+
+struct nv3052c_reg {
+ u8 cmd;
+ u8 val;
+};
+
+static const struct nv3052c_reg nv3052c_panel_regs[] = {
+ { 0xff, 0x30 },
+ { 0xff, 0x52 },
+ { 0xff, 0x01 },
+ { 0xe3, 0x00 },
+ { 0x40, 0x00 },
+ { 0x03, 0x40 },
+ { 0x04, 0x00 },
+ { 0x05, 0x03 },
+ { 0x08, 0x00 },
+ { 0x09, 0x07 },
+ { 0x0a, 0x01 },
+ { 0x0b, 0x32 },
+ { 0x0c, 0x32 },
+ { 0x0d, 0x0b },
+ { 0x0e, 0x00 },
+ { 0x23, 0xa0 },
+
+ { 0x24, 0x0c },
+ { 0x25, 0x06 },
+ { 0x26, 0x14 },
+ { 0x27, 0x14 },
+
+ { 0x38, 0xcc },
+ { 0x39, 0xd7 },
+ { 0x3a, 0x4a },
+
+ { 0x28, 0x40 },
+ { 0x29, 0x01 },
+ { 0x2a, 0xdf },
+ { 0x49, 0x3c },
+ { 0x91, 0x77 },
+ { 0x92, 0x77 },
+ { 0xa0, 0x55 },
+ { 0xa1, 0x50 },
+ { 0xa4, 0x9c },
+ { 0xa7, 0x02 },
+ { 0xa8, 0x01 },
+ { 0xa9, 0x01 },
+ { 0xaa, 0xfc },
+ { 0xab, 0x28 },
+ { 0xac, 0x06 },
+ { 0xad, 0x06 },
+ { 0xae, 0x06 },
+ { 0xaf, 0x03 },
+ { 0xb0, 0x08 },
+ { 0xb1, 0x26 },
+ { 0xb2, 0x28 },
+ { 0xb3, 0x28 },
+ { 0xb4, 0x33 },
+ { 0xb5, 0x08 },
+ { 0xb6, 0x26 },
+ { 0xb7, 0x08 },
+ { 0xb8, 0x26 },
+ { 0xf0, 0x00 },
+ { 0xf6, 0xc0 },
+
+ { 0xff, 0x30 },
+ { 0xff, 0x52 },
+ { 0xff, 0x02 },
+ { 0xb0, 0x0b },
+ { 0xb1, 0x16 },
+ { 0xb2, 0x17 },
+ { 0xb3, 0x2c },
+ { 0xb4, 0x32 },
+ { 0xb5, 0x3b },
+ { 0xb6, 0x29 },
+ { 0xb7, 0x40 },
+ { 0xb8, 0x0d },
+ { 0xb9, 0x05 },
+ { 0xba, 0x12 },
+ { 0xbb, 0x10 },
+ { 0xbc, 0x12 },
+ { 0xbd, 0x15 },
+ { 0xbe, 0x19 },
+ { 0xbf, 0x0e },
+ { 0xc0, 0x16 },
+ { 0xc1, 0x0a },
+ { 0xd0, 0x0c },
+ { 0xd1, 0x17 },
+ { 0xd2, 0x14 },
+ { 0xd3, 0x2e },
+ { 0xd4, 0x32 },
+ { 0xd5, 0x3c },
+ { 0xd6, 0x22 },
+ { 0xd7, 0x3d },
+ { 0xd8, 0x0d },
+ { 0xd9, 0x07 },
+ { 0xda, 0x13 },
+ { 0xdb, 0x13 },
+ { 0xdc, 0x11 },
+ { 0xdd, 0x15 },
+ { 0xde, 0x19 },
+ { 0xdf, 0x10 },
+ { 0xe0, 0x17 },
+ { 0xe1, 0x0a },
+
+ { 0xff, 0x30 },
+ { 0xff, 0x52 },
+ { 0xff, 0x03 },
+ { 0x00, 0x2a },
+ { 0x01, 0x2a },
+ { 0x02, 0x2a },
+ { 0x03, 0x2a },
+ { 0x04, 0x61 },
+ { 0x05, 0x80 },
+ { 0x06, 0xc7 },
+ { 0x07, 0x01 },
+ { 0x08, 0x03 },
+ { 0x09, 0x04 },
+ { 0x70, 0x22 },
+ { 0x71, 0x80 },
+ { 0x30, 0x2a },
+ { 0x31, 0x2a },
+ { 0x32, 0x2a },
+ { 0x33, 0x2a },
+ { 0x34, 0x61 },
+ { 0x35, 0xc5 },
+ { 0x36, 0x80 },
+ { 0x37, 0x23 },
+ { 0x40, 0x03 },
+ { 0x41, 0x04 },
+ { 0x42, 0x05 },
+ { 0x43, 0x06 },
+ { 0x44, 0x11 },
+ { 0x45, 0xe8 },
+ { 0x46, 0xe9 },
+ { 0x47, 0x11 },
+ { 0x48, 0xea },
+ { 0x49, 0xeb },
+ { 0x50, 0x07 },
+ { 0x51, 0x08 },
+ { 0x52, 0x09 },
+ { 0x53, 0x0a },
+ { 0x54, 0x11 },
+ { 0x55, 0xec },
+ { 0x56, 0xed },
+ { 0x57, 0x11 },
+ { 0x58, 0xef },
+ { 0x59, 0xf0 },
+ { 0xb1, 0x01 },
+ { 0xb4, 0x15 },
+ { 0xb5, 0x16 },
+ { 0xb6, 0x09 },
+ { 0xb7, 0x0f },
+ { 0xb8, 0x0d },
+ { 0xb9, 0x0b },
+ { 0xba, 0x00 },
+ { 0xc7, 0x02 },
+ { 0xca, 0x17 },
+ { 0xcb, 0x18 },
+ { 0xcc, 0x0a },
+ { 0xcd, 0x10 },
+ { 0xce, 0x0e },
+ { 0xcf, 0x0c },
+ { 0xd0, 0x00 },
+ { 0x81, 0x00 },
+ { 0x84, 0x15 },
+ { 0x85, 0x16 },
+ { 0x86, 0x10 },
+ { 0x87, 0x0a },
+ { 0x88, 0x0c },
+ { 0x89, 0x0e },
+ { 0x8a, 0x02 },
+ { 0x97, 0x00 },
+ { 0x9a, 0x17 },
+ { 0x9b, 0x18 },
+ { 0x9c, 0x0f },
+ { 0x9d, 0x09 },
+ { 0x9e, 0x0b },
+ { 0x9f, 0x0d },
+ { 0xa0, 0x01 },
+
+ { 0xff, 0x30 },
+ { 0xff, 0x52 },
+ { 0xff, 0x02 },
+ { 0x01, 0x01 },
+ { 0x02, 0xda },
+ { 0x03, 0xba },
+ { 0x04, 0xa8 },
+ { 0x05, 0x9a },
+ { 0x06, 0x70 },
+ { 0x07, 0xff },
+ { 0x08, 0x91 },
+ { 0x09, 0x90 },
+ { 0x0a, 0xff },
+ { 0x0b, 0x8f },
+ { 0x0c, 0x60 },
+ { 0x0d, 0x58 },
+ { 0x0e, 0x48 },
+ { 0x0f, 0x38 },
+ { 0x10, 0x2b },
+
+ { 0xff, 0x30 },
+ { 0xff, 0x52 },
+ { 0xff, 0x00 },
+ { 0x36, 0x0a },
+};
+
+static inline struct nv3052c *to_nv3052c(struct drm_panel *panel)
+{
+ return container_of(panel, struct nv3052c, panel);
+}
+
+static int nv3052c_prepare(struct drm_panel *panel)
+{
+ struct nv3052c *priv = to_nv3052c(panel);
+ struct mipi_dbi *dbi = &priv->dbi;
+ unsigned int i;
+ int err;
+
+ err = regulator_enable(priv->supply);
+ if (err) {
+ dev_err(priv->dev, "Failed to enable power supply: %d\n", err);
+ return err;
+ }
+
+ /* Reset the chip */
+ gpiod_set_value_cansleep(priv->reset_gpio, 1);
+ usleep_range(10, 1000);
+ gpiod_set_value_cansleep(priv->reset_gpio, 0);
+ msleep(5);
+
+ for (i = 0; i < ARRAY_SIZE(nv3052c_panel_regs); i++) {
+ err = mipi_dbi_command(dbi, nv3052c_panel_regs[i].cmd,
+ nv3052c_panel_regs[i].val);
+
+ if (err) {
+ dev_err(priv->dev, "Unable to set register: %d\n", err);
+ goto err_disable_regulator;
+ }
+ }
+
+ err = mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
+ if (err) {
+ dev_err(priv->dev, "Unable to exit sleep mode: %d\n", err);
+ goto err_disable_regulator;
+ }
+
+ return 0;
+
+err_disable_regulator:
+ regulator_disable(priv->supply);
+ return err;
+}
+
+static int nv3052c_unprepare(struct drm_panel *panel)
+{
+ struct nv3052c *priv = to_nv3052c(panel);
+ struct mipi_dbi *dbi = &priv->dbi;
+ int err;
+
+ err = mipi_dbi_command(dbi, MIPI_DCS_ENTER_SLEEP_MODE);
+ if (err) {
+ dev_err(priv->dev, "Unable to enter sleep mode: %d\n", err);
+ return err;
+ }
+
+ gpiod_set_value_cansleep(priv->reset_gpio, 1);
+ regulator_disable(priv->supply);
+
+ return 0;
+}
+
+static int nv3052c_enable(struct drm_panel *panel)
+{
+ struct nv3052c *priv = to_nv3052c(panel);
+ struct mipi_dbi *dbi = &priv->dbi;
+ int err;
+
+ err = mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
+ if (err) {
+ dev_err(priv->dev, "Unable to enable display: %d\n", err);
+ return err;
+ }
+
+ if (panel->backlight) {
+ /* Wait for the picture to be ready before enabling backlight */
+ msleep(120);
+ }
+
+ return 0;
+}
+
+static int nv3052c_disable(struct drm_panel *panel)
+{
+ struct nv3052c *priv = to_nv3052c(panel);
+ struct mipi_dbi *dbi = &priv->dbi;
+ int err;
+
+ err = mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF);
+ if (err) {
+ dev_err(priv->dev, "Unable to disable display: %d\n", err);
+ return err;
+ }
+
+ return 0;
+}
+
+static int nv3052c_get_modes(struct drm_panel *panel,
+ struct drm_connector *connector)
+{
+ struct nv3052c *priv = to_nv3052c(panel);
+ const struct nv3052c_panel_info *panel_info = priv->panel_info;
+ struct drm_display_mode *mode;
+ unsigned int i;
+
+ for (i = 0; i < panel_info->num_modes; i++) {
+ mode = drm_mode_duplicate(connector->dev,
+ &panel_info->display_modes[i]);
+ if (!mode)
+ return -ENOMEM;
+
+ drm_mode_set_name(mode);
+
+ mode->type = DRM_MODE_TYPE_DRIVER;
+ if (panel_info->num_modes == 1)
+ mode->type |= DRM_MODE_TYPE_PREFERRED;
+
+ drm_mode_probed_add(connector, mode);
+ }
+
+ connector->display_info.bpc = 8;
+ connector->display_info.width_mm = panel_info->width_mm;
+ connector->display_info.height_mm = panel_info->height_mm;
+
+ drm_display_info_set_bus_formats(&connector->display_info,
+ &panel_info->bus_format, 1);
+ connector->display_info.bus_flags = panel_info->bus_flags;
+
+ return panel_info->num_modes;
+}
+
+static const struct drm_panel_funcs nv3052c_funcs = {
+ .prepare = nv3052c_prepare,
+ .unprepare = nv3052c_unprepare,
+ .enable = nv3052c_enable,
+ .disable = nv3052c_disable,
+ .get_modes = nv3052c_get_modes,
+};
+
+static int nv3052c_probe(struct spi_device *spi)
+{
+ struct device *dev = &spi->dev;
+ struct nv3052c *priv;
+ int err;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->dev = dev;
+
+ priv->panel_info = of_device_get_match_data(dev);
+ if (!priv->panel_info)
+ return -EINVAL;
+
+ priv->supply = devm_regulator_get(dev, "power");
+ if (IS_ERR(priv->supply)) {
+ dev_err(dev, "Failed to get power supply\n");
+ return PTR_ERR(priv->supply);
+ }
+
+ priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(priv->reset_gpio)) {
+ dev_err(dev, "Failed to get reset GPIO\n");
+ return PTR_ERR(priv->reset_gpio);
+ }
+
+ err = mipi_dbi_spi_init(spi, &priv->dbi, NULL);
+ if (err)
+ return dev_err_probe(dev, err, "MIPI DBI init failed\n");
+
+ priv->dbi.read_commands = NULL;
+
+ spi_set_drvdata(spi, priv);
+
+ drm_panel_init(&priv->panel, dev, &nv3052c_funcs,
+ DRM_MODE_CONNECTOR_DPI);
+
+ err = drm_panel_of_backlight(&priv->panel);
+ if (err < 0) {
+ if (err != -EPROBE_DEFER)
+ dev_err(dev, "Failed to attach backlight\n");
+ return err;
+ }
+
+ drm_panel_add(&priv->panel);
+
+ return 0;
+}
+
+static int nv3052c_remove(struct spi_device *spi)
+{
+ struct nv3052c *priv = spi_get_drvdata(spi);
+
+ drm_panel_remove(&priv->panel);
+ drm_panel_disable(&priv->panel);
+ drm_panel_unprepare(&priv->panel);
+
+ return 0;
+}
+
+static const struct drm_display_mode ltk035c5444t_modes[] = {
+ { /* 60 Hz */
+ .clock = 24000,
+ .hdisplay = 640,
+ .hsync_start = 640 + 96,
+ .hsync_end = 640 + 96 + 16,
+ .htotal = 640 + 96 + 16 + 48,
+ .vdisplay = 480,
+ .vsync_start = 480 + 5,
+ .vsync_end = 480 + 5 + 2,
+ .vtotal = 480 + 5 + 2 + 13,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ },
+ { /* 50 Hz */
+ .clock = 18000,
+ .hdisplay = 640,
+ .hsync_start = 640 + 39,
+ .hsync_end = 640 + 39 + 2,
+ .htotal = 640 + 39 + 2 + 39,
+ .vdisplay = 480,
+ .vsync_start = 480 + 5,
+ .vsync_end = 480 + 5 + 2,
+ .vtotal = 480 + 5 + 2 + 13,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ },
+};
+
+static const struct nv3052c_panel_info ltk035c5444t_spi_panel_info = {
+ .display_modes = ltk035c5444t_modes,
+ .num_modes = ARRAY_SIZE(ltk035c5444t_modes),
+ .width_mm = 77,
+ .height_mm = 64,
+ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+ .bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+};
+
+static const struct of_device_id nv3052c_of_match[] = {
+ { .compatible = "leadtek,ltk035c5444t-spi", .data = <k035c5444t_spi_panel_info },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, nv3052c_of_match);
+
+static struct spi_driver nv3052c_driver = {
+ .driver = {
+ .name = "nv3052c",
+ .of_match_table = nv3052c_of_match,
+ },
+ .probe = nv3052c_probe,
+ .remove = nv3052c_remove,
+};
+module_spi_driver(nv3052c_driver);
+
+MODULE_AUTHOR("Paul Cercueil <[email protected]>");
+MODULE_AUTHOR("Christophe Branchereau <[email protected]>");
+MODULE_LICENSE("GPL v2");
--
2.34.1
This allows the CRTC to be enabled after panels have slept out,
and before their display is turned on, solving a graphical bug
on the newvision nv3502c
Signed-off-by: Christophe Branchereau <[email protected]>
---
drivers/gpu/drm/ingenic/ingenic-drm-drv.c | 19 +++++++++++++------
1 file changed, 13 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
index dcf44cb00821..51512f41263e 100644
--- a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
+++ b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
@@ -226,6 +226,18 @@ static int ingenic_drm_update_pixclk(struct notifier_block *nb,
}
}
+static void ingenic_drm_bridge_atomic_enable(struct drm_bridge *bridge,
+ struct drm_bridge_state *old_bridge_state)
+{
+ struct ingenic_drm *priv = drm_device_get_priv(bridge->dev);
+
+ regmap_write(priv->map, JZ_REG_LCD_STATE, 0);
+
+ regmap_update_bits(priv->map, JZ_REG_LCD_CTRL,
+ JZ_LCD_CTRL_ENABLE | JZ_LCD_CTRL_DISABLE,
+ JZ_LCD_CTRL_ENABLE);
+}
+
static void ingenic_drm_crtc_atomic_enable(struct drm_crtc *crtc,
struct drm_atomic_state *state)
{
@@ -237,17 +249,11 @@ static void ingenic_drm_crtc_atomic_enable(struct drm_crtc *crtc,
if (WARN_ON(IS_ERR(priv_state)))
return;
- regmap_write(priv->map, JZ_REG_LCD_STATE, 0);
-
/* Set addresses of our DMA descriptor chains */
next_id = priv_state->use_palette ? HWDESC_PALETTE : 0;
regmap_write(priv->map, JZ_REG_LCD_DA0, dma_hwdesc_addr(priv, next_id));
regmap_write(priv->map, JZ_REG_LCD_DA1, dma_hwdesc_addr(priv, 1));
- regmap_update_bits(priv->map, JZ_REG_LCD_CTRL,
- JZ_LCD_CTRL_ENABLE | JZ_LCD_CTRL_DISABLE,
- JZ_LCD_CTRL_ENABLE);
-
drm_crtc_vblank_on(crtc);
}
@@ -968,6 +974,7 @@ static const struct drm_encoder_helper_funcs ingenic_drm_encoder_helper_funcs =
static const struct drm_bridge_funcs ingenic_drm_bridge_funcs = {
.attach = ingenic_drm_bridge_attach,
+ .atomic_enable = ingenic_drm_bridge_atomic_enable,
.atomic_check = ingenic_drm_bridge_atomic_check,
.atomic_reset = drm_atomic_helper_bridge_reset,
.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
--
2.34.1
Hi Christophe,
Le mar., mars 1 2022 at 16:31:21 +0100, Christophe Branchereau
<[email protected]> a ?crit :
> This driver supports the NewVision NV3052C based LCDs. Right now, it
> only supports the LeadTek LTK035C5444T 2.4" 640x480 TFT LCD panel,
> which
> can be found in the Anbernic RG-350M handheld console.
You'd need to add a binding documentation for the NV3052C (in a
separate patch).
>
> Signed-off-by: Christophe Branchereau <[email protected]>
> ---
> drivers/gpu/drm/panel/Kconfig | 9 +
> drivers/gpu/drm/panel/Makefile | 1 +
> .../gpu/drm/panel/panel-newvision-nv3052c.c | 504
> ++++++++++++++++++
> 3 files changed, 514 insertions(+)
> create mode 100644 drivers/gpu/drm/panel/panel-newvision-nv3052c.c
>
> diff --git a/drivers/gpu/drm/panel/Kconfig
> b/drivers/gpu/drm/panel/Kconfig
> index bb2e47229c68..40084f709789 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -283,6 +283,15 @@ config DRM_PANEL_NEC_NL8048HL11
> panel (found on the Zoom2/3/3630 SDP boards). To compile this
> driver
> as a module, choose M here.
>
> +config DRM_PANEL_NEWVISION_NV3052C
> + tristate "NewVision NV3052C RGB/SPI panel"
> + depends on OF && SPI
> + depends on BACKLIGHT_CLASS_DEVICE
> + select DRM_MIPI_DBI
> + help
> + Say Y here if you want to enable support for the panels built
> + around the NewVision NV3052C display controller.
> +
> config DRM_PANEL_NOVATEK_NT35510
> tristate "Novatek NT35510 RGB panel driver"
> depends on OF
> diff --git a/drivers/gpu/drm/panel/Makefile
> b/drivers/gpu/drm/panel/Makefile
> index 5740911f637c..42a7ab54234b 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -26,6 +26,7 @@ obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK500HD1829) +=
> panel-leadtek-ltk500hd1829.o
> obj-$(CONFIG_DRM_PANEL_LG_LB035Q02) += panel-lg-lb035q02.o
> obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
> obj-$(CONFIG_DRM_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o
> +obj-$(CONFIG_DRM_PANEL_NEWVISION_NV3052C) +=
> panel-newvision-nv3052c.o
> obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35510) += panel-novatek-nt35510.o
> obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35560) += panel-novatek-nt35560.o
> obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35950) += panel-novatek-nt35950.o
> diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
> b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
> new file mode 100644
> index 000000000000..08a3b33bcce0
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-newvision-nv3052c.c
> @@ -0,0 +1,504 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * NevVision NV3052C IPS LCD panel driver
> + *
> + * Copyright (C) 2020, Paul Cercueil <[email protected]>
> + * Copyright (C) 2022, Christophe Branchereau
> <[email protected]>
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/media-bus-format.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/spi/spi.h>
> +
> +#include <video/mipi_display.h>
> +
> +#include <drm/drm_mipi_dbi.h>
> +#include <drm/drm_modes.h>
> +#include <drm/drm_panel.h>
> +
> +struct nv3052c_panel_info {
> + const struct drm_display_mode *display_modes;
> + unsigned int num_modes;
> + u16 width_mm, height_mm;
> + u32 bus_format, bus_flags;
> +};
> +
> +struct nv3052c {
> + struct device *dev;
> + struct drm_panel panel;
> + struct mipi_dbi dbi;
> +
> + const struct nv3052c_panel_info *panel_info;
> +
> + struct regulator *supply;
> + struct gpio_desc *reset_gpio;
> +};
> +
> +struct nv3052c_reg {
> + u8 cmd;
> + u8 val;
> +};
> +
> +static const struct nv3052c_reg nv3052c_panel_regs[] = {
> + { 0xff, 0x30 },
> + { 0xff, 0x52 },
> + { 0xff, 0x01 },
> + { 0xe3, 0x00 },
> + { 0x40, 0x00 },
> + { 0x03, 0x40 },
> + { 0x04, 0x00 },
> + { 0x05, 0x03 },
> + { 0x08, 0x00 },
> + { 0x09, 0x07 },
> + { 0x0a, 0x01 },
> + { 0x0b, 0x32 },
> + { 0x0c, 0x32 },
> + { 0x0d, 0x0b },
> + { 0x0e, 0x00 },
> + { 0x23, 0xa0 },
> +
> + { 0x24, 0x0c },
> + { 0x25, 0x06 },
> + { 0x26, 0x14 },
> + { 0x27, 0x14 },
> +
> + { 0x38, 0xcc },
> + { 0x39, 0xd7 },
> + { 0x3a, 0x4a },
> +
> + { 0x28, 0x40 },
> + { 0x29, 0x01 },
> + { 0x2a, 0xdf },
> + { 0x49, 0x3c },
> + { 0x91, 0x77 },
> + { 0x92, 0x77 },
> + { 0xa0, 0x55 },
> + { 0xa1, 0x50 },
> + { 0xa4, 0x9c },
> + { 0xa7, 0x02 },
> + { 0xa8, 0x01 },
> + { 0xa9, 0x01 },
> + { 0xaa, 0xfc },
> + { 0xab, 0x28 },
> + { 0xac, 0x06 },
> + { 0xad, 0x06 },
> + { 0xae, 0x06 },
> + { 0xaf, 0x03 },
> + { 0xb0, 0x08 },
> + { 0xb1, 0x26 },
> + { 0xb2, 0x28 },
> + { 0xb3, 0x28 },
> + { 0xb4, 0x33 },
> + { 0xb5, 0x08 },
> + { 0xb6, 0x26 },
> + { 0xb7, 0x08 },
> + { 0xb8, 0x26 },
> + { 0xf0, 0x00 },
> + { 0xf6, 0xc0 },
> +
> + { 0xff, 0x30 },
> + { 0xff, 0x52 },
> + { 0xff, 0x02 },
> + { 0xb0, 0x0b },
> + { 0xb1, 0x16 },
> + { 0xb2, 0x17 },
> + { 0xb3, 0x2c },
> + { 0xb4, 0x32 },
> + { 0xb5, 0x3b },
> + { 0xb6, 0x29 },
> + { 0xb7, 0x40 },
> + { 0xb8, 0x0d },
> + { 0xb9, 0x05 },
> + { 0xba, 0x12 },
> + { 0xbb, 0x10 },
> + { 0xbc, 0x12 },
> + { 0xbd, 0x15 },
> + { 0xbe, 0x19 },
> + { 0xbf, 0x0e },
> + { 0xc0, 0x16 },
> + { 0xc1, 0x0a },
> + { 0xd0, 0x0c },
> + { 0xd1, 0x17 },
> + { 0xd2, 0x14 },
> + { 0xd3, 0x2e },
> + { 0xd4, 0x32 },
> + { 0xd5, 0x3c },
> + { 0xd6, 0x22 },
> + { 0xd7, 0x3d },
> + { 0xd8, 0x0d },
> + { 0xd9, 0x07 },
> + { 0xda, 0x13 },
> + { 0xdb, 0x13 },
> + { 0xdc, 0x11 },
> + { 0xdd, 0x15 },
> + { 0xde, 0x19 },
> + { 0xdf, 0x10 },
> + { 0xe0, 0x17 },
> + { 0xe1, 0x0a },
> +
> + { 0xff, 0x30 },
> + { 0xff, 0x52 },
> + { 0xff, 0x03 },
> + { 0x00, 0x2a },
> + { 0x01, 0x2a },
> + { 0x02, 0x2a },
> + { 0x03, 0x2a },
> + { 0x04, 0x61 },
> + { 0x05, 0x80 },
> + { 0x06, 0xc7 },
> + { 0x07, 0x01 },
> + { 0x08, 0x03 },
> + { 0x09, 0x04 },
> + { 0x70, 0x22 },
> + { 0x71, 0x80 },
> + { 0x30, 0x2a },
> + { 0x31, 0x2a },
> + { 0x32, 0x2a },
> + { 0x33, 0x2a },
> + { 0x34, 0x61 },
> + { 0x35, 0xc5 },
> + { 0x36, 0x80 },
> + { 0x37, 0x23 },
> + { 0x40, 0x03 },
> + { 0x41, 0x04 },
> + { 0x42, 0x05 },
> + { 0x43, 0x06 },
> + { 0x44, 0x11 },
> + { 0x45, 0xe8 },
> + { 0x46, 0xe9 },
> + { 0x47, 0x11 },
> + { 0x48, 0xea },
> + { 0x49, 0xeb },
> + { 0x50, 0x07 },
> + { 0x51, 0x08 },
> + { 0x52, 0x09 },
> + { 0x53, 0x0a },
> + { 0x54, 0x11 },
> + { 0x55, 0xec },
> + { 0x56, 0xed },
> + { 0x57, 0x11 },
> + { 0x58, 0xef },
> + { 0x59, 0xf0 },
> + { 0xb1, 0x01 },
> + { 0xb4, 0x15 },
> + { 0xb5, 0x16 },
> + { 0xb6, 0x09 },
> + { 0xb7, 0x0f },
> + { 0xb8, 0x0d },
> + { 0xb9, 0x0b },
> + { 0xba, 0x00 },
> + { 0xc7, 0x02 },
> + { 0xca, 0x17 },
> + { 0xcb, 0x18 },
> + { 0xcc, 0x0a },
> + { 0xcd, 0x10 },
> + { 0xce, 0x0e },
> + { 0xcf, 0x0c },
> + { 0xd0, 0x00 },
> + { 0x81, 0x00 },
> + { 0x84, 0x15 },
> + { 0x85, 0x16 },
> + { 0x86, 0x10 },
> + { 0x87, 0x0a },
> + { 0x88, 0x0c },
> + { 0x89, 0x0e },
> + { 0x8a, 0x02 },
> + { 0x97, 0x00 },
> + { 0x9a, 0x17 },
> + { 0x9b, 0x18 },
> + { 0x9c, 0x0f },
> + { 0x9d, 0x09 },
> + { 0x9e, 0x0b },
> + { 0x9f, 0x0d },
> + { 0xa0, 0x01 },
> +
> + { 0xff, 0x30 },
> + { 0xff, 0x52 },
> + { 0xff, 0x02 },
> + { 0x01, 0x01 },
> + { 0x02, 0xda },
> + { 0x03, 0xba },
> + { 0x04, 0xa8 },
> + { 0x05, 0x9a },
> + { 0x06, 0x70 },
> + { 0x07, 0xff },
> + { 0x08, 0x91 },
> + { 0x09, 0x90 },
> + { 0x0a, 0xff },
> + { 0x0b, 0x8f },
> + { 0x0c, 0x60 },
> + { 0x0d, 0x58 },
> + { 0x0e, 0x48 },
> + { 0x0f, 0x38 },
> + { 0x10, 0x2b },
> +
> + { 0xff, 0x30 },
> + { 0xff, 0x52 },
> + { 0xff, 0x00 },
> + { 0x36, 0x0a },
> +};
> +
> +static inline struct nv3052c *to_nv3052c(struct drm_panel *panel)
> +{
> + return container_of(panel, struct nv3052c, panel);
> +}
> +
> +static int nv3052c_prepare(struct drm_panel *panel)
> +{
> + struct nv3052c *priv = to_nv3052c(panel);
> + struct mipi_dbi *dbi = &priv->dbi;
> + unsigned int i;
> + int err;
> +
> + err = regulator_enable(priv->supply);
> + if (err) {
> + dev_err(priv->dev, "Failed to enable power supply: %d\n", err);
> + return err;
> + }
> +
> + /* Reset the chip */
> + gpiod_set_value_cansleep(priv->reset_gpio, 1);
> + usleep_range(10, 1000);
> + gpiod_set_value_cansleep(priv->reset_gpio, 0);
> + msleep(5);
> +
> + for (i = 0; i < ARRAY_SIZE(nv3052c_panel_regs); i++) {
> + err = mipi_dbi_command(dbi, nv3052c_panel_regs[i].cmd,
> + nv3052c_panel_regs[i].val);
> +
> + if (err) {
> + dev_err(priv->dev, "Unable to set register: %d\n", err);
> + goto err_disable_regulator;
> + }
> + }
> +
> + err = mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
> + if (err) {
> + dev_err(priv->dev, "Unable to exit sleep mode: %d\n", err);
> + goto err_disable_regulator;
> + }
> +
> + return 0;
> +
> +err_disable_regulator:
> + regulator_disable(priv->supply);
> + return err;
> +}
> +
> +static int nv3052c_unprepare(struct drm_panel *panel)
> +{
> + struct nv3052c *priv = to_nv3052c(panel);
> + struct mipi_dbi *dbi = &priv->dbi;
> + int err;
> +
> + err = mipi_dbi_command(dbi, MIPI_DCS_ENTER_SLEEP_MODE);
> + if (err) {
> + dev_err(priv->dev, "Unable to enter sleep mode: %d\n", err);
> + return err;
> + }
> +
> + gpiod_set_value_cansleep(priv->reset_gpio, 1);
> + regulator_disable(priv->supply);
> +
> + return 0;
> +}
> +
> +static int nv3052c_enable(struct drm_panel *panel)
> +{
> + struct nv3052c *priv = to_nv3052c(panel);
> + struct mipi_dbi *dbi = &priv->dbi;
> + int err;
> +
> + err = mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
> + if (err) {
> + dev_err(priv->dev, "Unable to enable display: %d\n", err);
> + return err;
> + }
> +
> + if (panel->backlight) {
> + /* Wait for the picture to be ready before enabling backlight */
> + msleep(120);
> + }
> +
> + return 0;
> +}
> +
> +static int nv3052c_disable(struct drm_panel *panel)
> +{
> + struct nv3052c *priv = to_nv3052c(panel);
> + struct mipi_dbi *dbi = &priv->dbi;
> + int err;
> +
> + err = mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF);
> + if (err) {
> + dev_err(priv->dev, "Unable to disable display: %d\n", err);
> + return err;
> + }
> +
> + return 0;
> +}
> +
> +static int nv3052c_get_modes(struct drm_panel *panel,
> + struct drm_connector *connector)
> +{
> + struct nv3052c *priv = to_nv3052c(panel);
> + const struct nv3052c_panel_info *panel_info = priv->panel_info;
> + struct drm_display_mode *mode;
> + unsigned int i;
> +
> + for (i = 0; i < panel_info->num_modes; i++) {
> + mode = drm_mode_duplicate(connector->dev,
> + &panel_info->display_modes[i]);
> + if (!mode)
> + return -ENOMEM;
> +
> + drm_mode_set_name(mode);
> +
> + mode->type = DRM_MODE_TYPE_DRIVER;
> + if (panel_info->num_modes == 1)
> + mode->type |= DRM_MODE_TYPE_PREFERRED;
> +
> + drm_mode_probed_add(connector, mode);
> + }
> +
> + connector->display_info.bpc = 8;
> + connector->display_info.width_mm = panel_info->width_mm;
> + connector->display_info.height_mm = panel_info->height_mm;
> +
> + drm_display_info_set_bus_formats(&connector->display_info,
> + &panel_info->bus_format, 1);
> + connector->display_info.bus_flags = panel_info->bus_flags;
> +
> + return panel_info->num_modes;
> +}
> +
> +static const struct drm_panel_funcs nv3052c_funcs = {
> + .prepare = nv3052c_prepare,
> + .unprepare = nv3052c_unprepare,
> + .enable = nv3052c_enable,
> + .disable = nv3052c_disable,
> + .get_modes = nv3052c_get_modes,
> +};
> +
> +static int nv3052c_probe(struct spi_device *spi)
> +{
> + struct device *dev = &spi->dev;
> + struct nv3052c *priv;
> + int err;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + priv->dev = dev;
> +
> + priv->panel_info = of_device_get_match_data(dev);
> + if (!priv->panel_info)
> + return -EINVAL;
> +
> + priv->supply = devm_regulator_get(dev, "power");
> + if (IS_ERR(priv->supply)) {
> + dev_err(dev, "Failed to get power supply\n");
> + return PTR_ERR(priv->supply);
You can use dev_err_probe() here,
> + }
> +
> + priv->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> + if (IS_ERR(priv->reset_gpio)) {
> + dev_err(dev, "Failed to get reset GPIO\n");
> + return PTR_ERR(priv->reset_gpio);
and here as well, since devm_{regulator,gpiod}_get() may return
-EPROBE_DEFER.
The rest of the driver looks fine to me.
Cheers,
-Paul
> + }
> +
> + err = mipi_dbi_spi_init(spi, &priv->dbi, NULL);
> + if (err)
> + return dev_err_probe(dev, err, "MIPI DBI init failed\n");
> +
> + priv->dbi.read_commands = NULL;
> +
> + spi_set_drvdata(spi, priv);
> +
> + drm_panel_init(&priv->panel, dev, &nv3052c_funcs,
> + DRM_MODE_CONNECTOR_DPI);
> +
> + err = drm_panel_of_backlight(&priv->panel);
> + if (err < 0) {
> + if (err != -EPROBE_DEFER)
> + dev_err(dev, "Failed to attach backlight\n");
> + return err;
> + }
> +
> + drm_panel_add(&priv->panel);
> +
> + return 0;
> +}
> +
> +static int nv3052c_remove(struct spi_device *spi)
> +{
> + struct nv3052c *priv = spi_get_drvdata(spi);
> +
> + drm_panel_remove(&priv->panel);
> + drm_panel_disable(&priv->panel);
> + drm_panel_unprepare(&priv->panel);
> +
> + return 0;
> +}
> +
> +static const struct drm_display_mode ltk035c5444t_modes[] = {
> + { /* 60 Hz */
> + .clock = 24000,
> + .hdisplay = 640,
> + .hsync_start = 640 + 96,
> + .hsync_end = 640 + 96 + 16,
> + .htotal = 640 + 96 + 16 + 48,
> + .vdisplay = 480,
> + .vsync_start = 480 + 5,
> + .vsync_end = 480 + 5 + 2,
> + .vtotal = 480 + 5 + 2 + 13,
> + .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> + },
> + { /* 50 Hz */
> + .clock = 18000,
> + .hdisplay = 640,
> + .hsync_start = 640 + 39,
> + .hsync_end = 640 + 39 + 2,
> + .htotal = 640 + 39 + 2 + 39,
> + .vdisplay = 480,
> + .vsync_start = 480 + 5,
> + .vsync_end = 480 + 5 + 2,
> + .vtotal = 480 + 5 + 2 + 13,
> + .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> + },
> +};
> +
> +static const struct nv3052c_panel_info ltk035c5444t_spi_panel_info =
> {
> + .display_modes = ltk035c5444t_modes,
> + .num_modes = ARRAY_SIZE(ltk035c5444t_modes),
> + .width_mm = 77,
> + .height_mm = 64,
> + .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> + .bus_flags = DRM_BUS_FLAG_DE_HIGH |
> DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
> +};
> +
> +static const struct of_device_id nv3052c_of_match[] = {
> + { .compatible = "leadtek,ltk035c5444t-spi", .data =
> <k035c5444t_spi_panel_info },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, nv3052c_of_match);
> +
> +static struct spi_driver nv3052c_driver = {
> + .driver = {
> + .name = "nv3052c",
> + .of_match_table = nv3052c_of_match,
> + },
> + .probe = nv3052c_probe,
> + .remove = nv3052c_remove,
> +};
> +module_spi_driver(nv3052c_driver);
> +
> +MODULE_AUTHOR("Paul Cercueil <[email protected]>");
> +MODULE_AUTHOR("Christophe Branchereau <[email protected]>");
> +MODULE_LICENSE("GPL v2");
> --
> 2.34.1
>
Hi Christophe,
Le mar., mars 1 2022 at 16:31:22 +0100, Christophe Branchereau
<[email protected]> a ?crit :
> Following the introduction of bridge_atomic_enable in the ingenic
> drm driver, the crtc is enabled between .prepare and .enable, if
> it exists.
>
> Add it so the backlight is only enabled after the crtc is, to avoid
> graphical issues.
>
> Signed-off-by: Christophe Branchereau <[email protected]>
> ---
> drivers/gpu/drm/panel/panel-abt-y030xx067a.c | 23 ++++++++++++--
> drivers/gpu/drm/panel/panel-innolux-ej030na.c | 31
> ++++++++++++++++---
> 2 files changed, 48 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> index f043b484055b..b5736344e3ec 100644
> --- a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> +++ b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> @@ -183,8 +183,6 @@ static int y030xx067a_prepare(struct drm_panel
> *panel)
> goto err_disable_regulator;
> }
>
> - msleep(120);
> -
> return 0;
>
> err_disable_regulator:
> @@ -202,6 +200,25 @@ static int y030xx067a_unprepare(struct drm_panel
> *panel)
> return 0;
> }
>
> +static int y030xx067a_enable(struct drm_panel *panel)
> +{
> + if (panel->backlight) {
> + /* Wait for the picture to be ready before enabling backlight */
> + msleep(120);
> + }
> +
> + return 0;
> +}
> +
> +static int y030xx067a_disable(struct drm_panel *panel)
> +{
> + struct y030xx067a *priv = to_y030xx067a(panel);
> +
> + regmap_clear_bits(priv->map, 0x06, REG06_XPSAVE);
Shouldn't that be balanced by a regmap_set_bits() in the .enable()
function?
Cheers,
-Paul
> +
> + return 0;
> +}
> +
> static int y030xx067a_get_modes(struct drm_panel *panel,
> struct drm_connector *connector)
> {
> @@ -239,6 +256,8 @@ static int y030xx067a_get_modes(struct drm_panel
> *panel,
> static const struct drm_panel_funcs y030xx067a_funcs = {
> .prepare = y030xx067a_prepare,
> .unprepare = y030xx067a_unprepare,
> + .enable = y030xx067a_enable,
> + .disable = y030xx067a_disable,
> .get_modes = y030xx067a_get_modes,
> };
>
> diff --git a/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> index c558de3f99be..6de7370185cd 100644
> --- a/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> +++ b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> @@ -80,8 +80,6 @@ static const struct reg_sequence
> ej030na_init_sequence[] = {
> { 0x47, 0x08 },
> { 0x48, 0x0f },
> { 0x49, 0x0f },
> -
> - { 0x2b, 0x01 },
> };
>
> static int ej030na_prepare(struct drm_panel *panel)
> @@ -109,8 +107,6 @@ static int ej030na_prepare(struct drm_panel
> *panel)
> goto err_disable_regulator;
> }
>
> - msleep(120);
> -
> return 0;
>
> err_disable_regulator:
> @@ -128,6 +124,31 @@ static int ej030na_unprepare(struct drm_panel
> *panel)
> return 0;
> }
>
> +static int ej030na_enable(struct drm_panel *panel)
> +{
> + struct ej030na *priv = to_ej030na(panel);
> +
> + /* standby off */
> + regmap_write(priv->map, 0x2b, 0x01);
> +
> + if (panel->backlight) {
> + /* Wait for the picture to be ready before enabling backlight */
> + msleep(120);
> + }
> +
> + return 0;
> +}
> +
> +static int ej030na_disable(struct drm_panel *panel)
> +{
> + struct ej030na *priv = to_ej030na(panel);
> +
> + /* standby on */
> + regmap_write(priv->map, 0x2b, 0x00);
> +
> + return 0;
> +}
> +
> static int ej030na_get_modes(struct drm_panel *panel,
> struct drm_connector *connector)
> {
> @@ -165,6 +186,8 @@ static int ej030na_get_modes(struct drm_panel
> *panel,
> static const struct drm_panel_funcs ej030na_funcs = {
> .prepare = ej030na_prepare,
> .unprepare = ej030na_unprepare,
> + .enable = ej030na_enable,
> + .disable = ej030na_disable,
> .get_modes = ej030na_get_modes,
> };
>
> --
> 2.34.1
>
Hi Paul, it should in theory, but doesn't work in practice, the
display doesn't like having that bit set outside of the init sequence.
Feel free to experiment if you think you can make it work though, you
should have that panel on 1 or 2 devices I think.
KR
CB
On Wed, Mar 2, 2022 at 12:22 PM Paul Cercueil <[email protected]> wrote:
>
> Hi Christophe,
>
> Le mar., mars 1 2022 at 16:31:22 +0100, Christophe Branchereau
> <[email protected]> a écrit :
> > Following the introduction of bridge_atomic_enable in the ingenic
> > drm driver, the crtc is enabled between .prepare and .enable, if
> > it exists.
> >
> > Add it so the backlight is only enabled after the crtc is, to avoid
> > graphical issues.
> >
> > Signed-off-by: Christophe Branchereau <[email protected]>
> > ---
> > drivers/gpu/drm/panel/panel-abt-y030xx067a.c | 23 ++++++++++++--
> > drivers/gpu/drm/panel/panel-innolux-ej030na.c | 31
> > ++++++++++++++++---
> > 2 files changed, 48 insertions(+), 6 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> > b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> > index f043b484055b..b5736344e3ec 100644
> > --- a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> > +++ b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> > @@ -183,8 +183,6 @@ static int y030xx067a_prepare(struct drm_panel
> > *panel)
> > goto err_disable_regulator;
> > }
> >
> > - msleep(120);
> > -
> > return 0;
> >
> > err_disable_regulator:
> > @@ -202,6 +200,25 @@ static int y030xx067a_unprepare(struct drm_panel
> > *panel)
> > return 0;
> > }
> >
> > +static int y030xx067a_enable(struct drm_panel *panel)
> > +{
> > + if (panel->backlight) {
> > + /* Wait for the picture to be ready before enabling backlight */
> > + msleep(120);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int y030xx067a_disable(struct drm_panel *panel)
> > +{
> > + struct y030xx067a *priv = to_y030xx067a(panel);
> > +
> > + regmap_clear_bits(priv->map, 0x06, REG06_XPSAVE);
>
> Shouldn't that be balanced by a regmap_set_bits() in the .enable()
> function?
>
> Cheers,
> -Paul
>
> > +
> > + return 0;
> > +}
> > +
> > static int y030xx067a_get_modes(struct drm_panel *panel,
> > struct drm_connector *connector)
> > {
> > @@ -239,6 +256,8 @@ static int y030xx067a_get_modes(struct drm_panel
> > *panel,
> > static const struct drm_panel_funcs y030xx067a_funcs = {
> > .prepare = y030xx067a_prepare,
> > .unprepare = y030xx067a_unprepare,
> > + .enable = y030xx067a_enable,
> > + .disable = y030xx067a_disable,
> > .get_modes = y030xx067a_get_modes,
> > };
> >
> > diff --git a/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> > b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> > index c558de3f99be..6de7370185cd 100644
> > --- a/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> > +++ b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> > @@ -80,8 +80,6 @@ static const struct reg_sequence
> > ej030na_init_sequence[] = {
> > { 0x47, 0x08 },
> > { 0x48, 0x0f },
> > { 0x49, 0x0f },
> > -
> > - { 0x2b, 0x01 },
> > };
> >
> > static int ej030na_prepare(struct drm_panel *panel)
> > @@ -109,8 +107,6 @@ static int ej030na_prepare(struct drm_panel
> > *panel)
> > goto err_disable_regulator;
> > }
> >
> > - msleep(120);
> > -
> > return 0;
> >
> > err_disable_regulator:
> > @@ -128,6 +124,31 @@ static int ej030na_unprepare(struct drm_panel
> > *panel)
> > return 0;
> > }
> >
> > +static int ej030na_enable(struct drm_panel *panel)
> > +{
> > + struct ej030na *priv = to_ej030na(panel);
> > +
> > + /* standby off */
> > + regmap_write(priv->map, 0x2b, 0x01);
> > +
> > + if (panel->backlight) {
> > + /* Wait for the picture to be ready before enabling backlight */
> > + msleep(120);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ej030na_disable(struct drm_panel *panel)
> > +{
> > + struct ej030na *priv = to_ej030na(panel);
> > +
> > + /* standby on */
> > + regmap_write(priv->map, 0x2b, 0x00);
> > +
> > + return 0;
> > +}
> > +
> > static int ej030na_get_modes(struct drm_panel *panel,
> > struct drm_connector *connector)
> > {
> > @@ -165,6 +186,8 @@ static int ej030na_get_modes(struct drm_panel
> > *panel,
> > static const struct drm_panel_funcs ej030na_funcs = {
> > .prepare = ej030na_prepare,
> > .unprepare = ej030na_unprepare,
> > + .enable = ej030na_enable,
> > + .disable = ej030na_disable,
> > .get_modes = ej030na_get_modes,
> > };
> >
> > --
> > 2.34.1
> >
>
>
Hi Christophe,
Le lun., mars 7 2022 at 19:12:49 +0100, Christophe Branchereau
<[email protected]> a ?crit :
> Hi Paul, it should in theory, but doesn't work in practice, the
> display doesn't like having that bit set outside of the init sequence.
>
> Feel free to experiment if you think you can make it work though, you
> should have that panel on 1 or 2 devices I think.
It does actually work in practice; what probably fails for you is the
regmap_set_bits(), which causes a spi-read-then-write. Since AFAIK it
is not possible to read registers from this panel (only write), then
this does not work.
An easy fix would be to just use REGCACHE_FLAT as the cache type in the
regmap_config. Then regmap_set_bits() can be used.
Cheers,
-Paul
>
> KR
> CB
>
> On Wed, Mar 2, 2022 at 12:22 PM Paul Cercueil <[email protected]>
> wrote:
>>
>> Hi Christophe,
>>
>> Le mar., mars 1 2022 at 16:31:22 +0100, Christophe Branchereau
>> <[email protected]> a ?crit :
>> > Following the introduction of bridge_atomic_enable in the ingenic
>> > drm driver, the crtc is enabled between .prepare and .enable, if
>> > it exists.
>> >
>> > Add it so the backlight is only enabled after the crtc is, to
>> avoid
>> > graphical issues.
>> >
>> > Signed-off-by: Christophe Branchereau <[email protected]>
>> > ---
>> > drivers/gpu/drm/panel/panel-abt-y030xx067a.c | 23 ++++++++++++--
>> > drivers/gpu/drm/panel/panel-innolux-ej030na.c | 31
>> > ++++++++++++++++---
>> > 2 files changed, 48 insertions(+), 6 deletions(-)
>> >
>> > diff --git a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
>> > b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
>> > index f043b484055b..b5736344e3ec 100644
>> > --- a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
>> > +++ b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
>> > @@ -183,8 +183,6 @@ static int y030xx067a_prepare(struct drm_panel
>> > *panel)
>> > goto err_disable_regulator;
>> > }
>> >
>> > - msleep(120);
>> > -
>> > return 0;
>> >
>> > err_disable_regulator:
>> > @@ -202,6 +200,25 @@ static int y030xx067a_unprepare(struct
>> drm_panel
>> > *panel)
>> > return 0;
>> > }
>> >
>> > +static int y030xx067a_enable(struct drm_panel *panel)
>> > +{
>> > + if (panel->backlight) {
>> > + /* Wait for the picture to be ready before enabling
>> backlight */
>> > + msleep(120);
>> > + }
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static int y030xx067a_disable(struct drm_panel *panel)
>> > +{
>> > + struct y030xx067a *priv = to_y030xx067a(panel);
>> > +
>> > + regmap_clear_bits(priv->map, 0x06, REG06_XPSAVE);
>>
>> Shouldn't that be balanced by a regmap_set_bits() in the .enable()
>> function?
>>
>> Cheers,
>> -Paul
>>
>> > +
>> > + return 0;
>> > +}
>> > +
>> > static int y030xx067a_get_modes(struct drm_panel *panel,
>> > struct drm_connector *connector)
>> > {
>> > @@ -239,6 +256,8 @@ static int y030xx067a_get_modes(struct
>> drm_panel
>> > *panel,
>> > static const struct drm_panel_funcs y030xx067a_funcs = {
>> > .prepare = y030xx067a_prepare,
>> > .unprepare = y030xx067a_unprepare,
>> > + .enable = y030xx067a_enable,
>> > + .disable = y030xx067a_disable,
>> > .get_modes = y030xx067a_get_modes,
>> > };
>> >
>> > diff --git a/drivers/gpu/drm/panel/panel-innolux-ej030na.c
>> > b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
>> > index c558de3f99be..6de7370185cd 100644
>> > --- a/drivers/gpu/drm/panel/panel-innolux-ej030na.c
>> > +++ b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
>> > @@ -80,8 +80,6 @@ static const struct reg_sequence
>> > ej030na_init_sequence[] = {
>> > { 0x47, 0x08 },
>> > { 0x48, 0x0f },
>> > { 0x49, 0x0f },
>> > -
>> > - { 0x2b, 0x01 },
>> > };
>> >
>> > static int ej030na_prepare(struct drm_panel *panel)
>> > @@ -109,8 +107,6 @@ static int ej030na_prepare(struct drm_panel
>> > *panel)
>> > goto err_disable_regulator;
>> > }
>> >
>> > - msleep(120);
>> > -
>> > return 0;
>> >
>> > err_disable_regulator:
>> > @@ -128,6 +124,31 @@ static int ej030na_unprepare(struct drm_panel
>> > *panel)
>> > return 0;
>> > }
>> >
>> > +static int ej030na_enable(struct drm_panel *panel)
>> > +{
>> > + struct ej030na *priv = to_ej030na(panel);
>> > +
>> > + /* standby off */
>> > + regmap_write(priv->map, 0x2b, 0x01);
>> > +
>> > + if (panel->backlight) {
>> > + /* Wait for the picture to be ready before enabling
>> backlight */
>> > + msleep(120);
>> > + }
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static int ej030na_disable(struct drm_panel *panel)
>> > +{
>> > + struct ej030na *priv = to_ej030na(panel);
>> > +
>> > + /* standby on */
>> > + regmap_write(priv->map, 0x2b, 0x00);
>> > +
>> > + return 0;
>> > +}
>> > +
>> > static int ej030na_get_modes(struct drm_panel *panel,
>> > struct drm_connector *connector)
>> > {
>> > @@ -165,6 +186,8 @@ static int ej030na_get_modes(struct drm_panel
>> > *panel,
>> > static const struct drm_panel_funcs ej030na_funcs = {
>> > .prepare = ej030na_prepare,
>> > .unprepare = ej030na_unprepare,
>> > + .enable = ej030na_enable,
>> > + .disable = ej030na_disable,
>> > .get_modes = ej030na_get_modes,
>> > };
>> >
>> > --
>> > 2.34.1
>> >
>>
>>
Hi Paul, yes that works fine, thanks for checking it out
On Mon, Mar 14, 2022 at 9:54 PM Paul Cercueil <[email protected]> wrote:
>
> Hi Christophe,
>
> Le lun., mars 7 2022 at 19:12:49 +0100, Christophe Branchereau
> <[email protected]> a écrit :
> > Hi Paul, it should in theory, but doesn't work in practice, the
> > display doesn't like having that bit set outside of the init sequence.
> >
> > Feel free to experiment if you think you can make it work though, you
> > should have that panel on 1 or 2 devices I think.
>
> It does actually work in practice; what probably fails for you is the
> regmap_set_bits(), which causes a spi-read-then-write. Since AFAIK it
> is not possible to read registers from this panel (only write), then
> this does not work.
>
> An easy fix would be to just use REGCACHE_FLAT as the cache type in the
> regmap_config. Then regmap_set_bits() can be used.
>
> Cheers,
> -Paul
>
> >
> > KR
> > CB
> >
> > On Wed, Mar 2, 2022 at 12:22 PM Paul Cercueil <[email protected]>
> > wrote:
> >>
> >> Hi Christophe,
> >>
> >> Le mar., mars 1 2022 at 16:31:22 +0100, Christophe Branchereau
> >> <[email protected]> a écrit :
> >> > Following the introduction of bridge_atomic_enable in the ingenic
> >> > drm driver, the crtc is enabled between .prepare and .enable, if
> >> > it exists.
> >> >
> >> > Add it so the backlight is only enabled after the crtc is, to
> >> avoid
> >> > graphical issues.
> >> >
> >> > Signed-off-by: Christophe Branchereau <[email protected]>
> >> > ---
> >> > drivers/gpu/drm/panel/panel-abt-y030xx067a.c | 23 ++++++++++++--
> >> > drivers/gpu/drm/panel/panel-innolux-ej030na.c | 31
> >> > ++++++++++++++++---
> >> > 2 files changed, 48 insertions(+), 6 deletions(-)
> >> >
> >> > diff --git a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> >> > b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> >> > index f043b484055b..b5736344e3ec 100644
> >> > --- a/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> >> > +++ b/drivers/gpu/drm/panel/panel-abt-y030xx067a.c
> >> > @@ -183,8 +183,6 @@ static int y030xx067a_prepare(struct drm_panel
> >> > *panel)
> >> > goto err_disable_regulator;
> >> > }
> >> >
> >> > - msleep(120);
> >> > -
> >> > return 0;
> >> >
> >> > err_disable_regulator:
> >> > @@ -202,6 +200,25 @@ static int y030xx067a_unprepare(struct
> >> drm_panel
> >> > *panel)
> >> > return 0;
> >> > }
> >> >
> >> > +static int y030xx067a_enable(struct drm_panel *panel)
> >> > +{
> >> > + if (panel->backlight) {
> >> > + /* Wait for the picture to be ready before enabling
> >> backlight */
> >> > + msleep(120);
> >> > + }
> >> > +
> >> > + return 0;
> >> > +}
> >> > +
> >> > +static int y030xx067a_disable(struct drm_panel *panel)
> >> > +{
> >> > + struct y030xx067a *priv = to_y030xx067a(panel);
> >> > +
> >> > + regmap_clear_bits(priv->map, 0x06, REG06_XPSAVE);
> >>
> >> Shouldn't that be balanced by a regmap_set_bits() in the .enable()
> >> function?
> >>
> >> Cheers,
> >> -Paul
> >>
> >> > +
> >> > + return 0;
> >> > +}
> >> > +
> >> > static int y030xx067a_get_modes(struct drm_panel *panel,
> >> > struct drm_connector *connector)
> >> > {
> >> > @@ -239,6 +256,8 @@ static int y030xx067a_get_modes(struct
> >> drm_panel
> >> > *panel,
> >> > static const struct drm_panel_funcs y030xx067a_funcs = {
> >> > .prepare = y030xx067a_prepare,
> >> > .unprepare = y030xx067a_unprepare,
> >> > + .enable = y030xx067a_enable,
> >> > + .disable = y030xx067a_disable,
> >> > .get_modes = y030xx067a_get_modes,
> >> > };
> >> >
> >> > diff --git a/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> >> > b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> >> > index c558de3f99be..6de7370185cd 100644
> >> > --- a/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> >> > +++ b/drivers/gpu/drm/panel/panel-innolux-ej030na.c
> >> > @@ -80,8 +80,6 @@ static const struct reg_sequence
> >> > ej030na_init_sequence[] = {
> >> > { 0x47, 0x08 },
> >> > { 0x48, 0x0f },
> >> > { 0x49, 0x0f },
> >> > -
> >> > - { 0x2b, 0x01 },
> >> > };
> >> >
> >> > static int ej030na_prepare(struct drm_panel *panel)
> >> > @@ -109,8 +107,6 @@ static int ej030na_prepare(struct drm_panel
> >> > *panel)
> >> > goto err_disable_regulator;
> >> > }
> >> >
> >> > - msleep(120);
> >> > -
> >> > return 0;
> >> >
> >> > err_disable_regulator:
> >> > @@ -128,6 +124,31 @@ static int ej030na_unprepare(struct drm_panel
> >> > *panel)
> >> > return 0;
> >> > }
> >> >
> >> > +static int ej030na_enable(struct drm_panel *panel)
> >> > +{
> >> > + struct ej030na *priv = to_ej030na(panel);
> >> > +
> >> > + /* standby off */
> >> > + regmap_write(priv->map, 0x2b, 0x01);
> >> > +
> >> > + if (panel->backlight) {
> >> > + /* Wait for the picture to be ready before enabling
> >> backlight */
> >> > + msleep(120);
> >> > + }
> >> > +
> >> > + return 0;
> >> > +}
> >> > +
> >> > +static int ej030na_disable(struct drm_panel *panel)
> >> > +{
> >> > + struct ej030na *priv = to_ej030na(panel);
> >> > +
> >> > + /* standby on */
> >> > + regmap_write(priv->map, 0x2b, 0x00);
> >> > +
> >> > + return 0;
> >> > +}
> >> > +
> >> > static int ej030na_get_modes(struct drm_panel *panel,
> >> > struct drm_connector *connector)
> >> > {
> >> > @@ -165,6 +186,8 @@ static int ej030na_get_modes(struct drm_panel
> >> > *panel,
> >> > static const struct drm_panel_funcs ej030na_funcs = {
> >> > .prepare = ej030na_prepare,
> >> > .unprepare = ej030na_unprepare,
> >> > + .enable = ej030na_enable,
> >> > + .disable = ej030na_disable,
> >> > .get_modes = ej030na_get_modes,
> >> > };
> >> >
> >> > --
> >> > 2.34.1
> >> >
> >>
> >>
>
>