Add KT PHd protocol driver.
Signed-off-by: Ondrej Zary <[email protected]>
---
drivers/ata/pata_parport/Kconfig | 11 +++
drivers/ata/pata_parport/Makefile | 1 +
drivers/ata/pata_parport/ktti.c | 112 ++++++++++++++++++++++++++++++
3 files changed, 124 insertions(+)
create mode 100644 drivers/ata/pata_parport/ktti.c
diff --git a/drivers/ata/pata_parport/Kconfig b/drivers/ata/pata_parport/Kconfig
index 004e5cf708f1..4505a037591a 100644
--- a/drivers/ata/pata_parport/Kconfig
+++ b/drivers/ata/pata_parport/Kconfig
@@ -154,3 +154,14 @@ config PATA_PARPORT_KBIC
kernel, you may answer Y here to build in the protocol driver,
otherwise you should answer M to build it as a loadable module. The
module will be called kbic.
+
+config PATA_PARPORT_KTTI
+ tristate "KT PHd protocol"
+ depends on PATA_PARPORT
+ help
+ This option enables support for the "PHd" parallel port IDE protocol
+ from KT Technology. This is a simple (low speed) adapter that is
+ used in some 2.5" portable hard drives. If you chose to build PATA_PARPORT
+ support into your kernel, you may answer Y here to build in the
+ protocol driver, otherwise you should answer M to build it as a
+ loadable module. The module will be called ktti.
diff --git a/drivers/ata/pata_parport/Makefile b/drivers/ata/pata_parport/Makefile
index e82fded22da3..0c31cf55c96b 100644
--- a/drivers/ata/pata_parport/Makefile
+++ b/drivers/ata/pata_parport/Makefile
@@ -19,3 +19,4 @@ obj-$(CONFIG_PATA_PARPORT_EPIA) += epia.o
obj-$(CONFIG_PATA_PARPORT_FRIQ) += friq.o
obj-$(CONFIG_PATA_PARPORT_FRPW) += frpw.o
obj-$(CONFIG_PATA_PARPORT_KBIC) += kbic.o
+obj-$(CONFIG_PATA_PARPORT_KTTI) += ktti.o
diff --git a/drivers/ata/pata_parport/ktti.c b/drivers/ata/pata_parport/ktti.c
new file mode 100644
index 000000000000..4604bbd41b18
--- /dev/null
+++ b/drivers/ata/pata_parport/ktti.c
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ktti.c (c) 1998 Grant R. Guenther <[email protected]>
+ * Under the terms of the GNU General Public License.
+ *
+ * ktti.c is a low-level protocol driver for the KT Technology
+ * parallel port adapter. This adapter is used in the "PHd"
+ * portable hard-drives. As far as I can tell, this device
+ * supports 4-bit mode _only_.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/wait.h>
+#include <linux/io.h>
+
+#include "pata_parport.h"
+
+#define j44(a, b) (((a >> 4) & 0x0f) | (b & 0xf0))
+
+/* cont = 0 - access the IDE register file
+ * cont = 1 - access the IDE command set
+ */
+
+static int cont_map[2] = { 0x10, 0x08 };
+
+static void ktti_write_regr(struct pi_adapter *pi, int cont, int regr, int val)
+{
+ int r = regr + cont_map[cont];
+
+ w0(r); w2(0xb); w2(0xa); w2(3); w2(6);
+ w0(val); w2(3); w0(0); w2(6); w2(0xb);
+}
+
+static int ktti_read_regr(struct pi_adapter *pi, int cont, int regr)
+{
+ int a, b, r;
+
+ r = regr + cont_map[cont];
+
+ w0(r); w2(0xb); w2(0xa); w2(9); w2(0xc); w2(9);
+ a = r1(); w2(0xc); b = r1(); w2(9); w2(0xc); w2(9);
+ return j44(a, b);
+}
+
+static void ktti_read_block(struct pi_adapter *pi, char *buf, int count)
+{
+ int k, a, b;
+
+ for (k = 0; k < count / 2; k++) {
+ w0(0x10); w2(0xb); w2(0xa); w2(9); w2(0xc); w2(9);
+ a = r1(); w2(0xc); b = r1(); w2(9);
+ buf[2 * k] = j44(a, b);
+ a = r1(); w2(0xc); b = r1(); w2(9);
+ buf[2 * k + 1] = j44(a, b);
+ }
+}
+
+static void ktti_write_block(struct pi_adapter *pi, char *buf, int count)
+{
+ int k;
+
+ for (k = 0; k < count / 2; k++) {
+ w0(0x10); w2(0xb); w2(0xa); w2(3); w2(6);
+ w0(buf[2 * k]); w2(3);
+ w0(buf[2 * k + 1]); w2(6);
+ w2(0xb);
+ }
+}
+
+static void ktti_connect(struct pi_adapter *pi)
+{
+ pi->saved_r0 = r0();
+ pi->saved_r2 = r2();
+ w2(0xb); w2(0xa); w0(0); w2(3); w2(6);
+}
+
+static void ktti_disconnect(struct pi_adapter *pi)
+{
+ w2(0xb); w2(0xa); w0(0xa0); w2(3); w2(4);
+ w0(pi->saved_r0);
+ w2(pi->saved_r2);
+}
+
+static void ktti_log_adapter(struct pi_adapter *pi, char *scratch, int verbose)
+{
+ dev_info(&pi->dev, "ktti, KT adapter at 0x%x, delay %d\n",
+ pi->port, pi->delay);
+}
+
+static struct pi_protocol ktti = {
+ .owner = THIS_MODULE,
+ .name = "ktti",
+ .max_mode = 1,
+ .epp_first = 2,
+ .default_delay = 1,
+ .max_units = 1,
+ .write_regr = ktti_write_regr,
+ .read_regr = ktti_read_regr,
+ .write_block = ktti_write_block,
+ .read_block = ktti_read_block,
+ .connect = ktti_connect,
+ .disconnect = ktti_disconnect,
+ .log_adapter = ktti_log_adapter,
+ .sht = { PATA_PARPORT_SHT("pata_parport-ktti") },
+};
+
+MODULE_LICENSE("GPL");
+module_pata_parport_driver(ktti);
--
Ondrej Zary