This series adds the gpi_dma nodes followed by the i2c and spi nodes for the
three qups found in the SM8450 SoC.
While at it, iommus was missing for qup0/qup1, so fix that up too.
Lastly enable the spi and i2c nodes found on the QRD board.
Vinod Koul (7):
arm64: dts: qcom: sm8450: Add gpi_dma nodes
arm64: dts: qcom: sm8450: Fix missing iommus for qup
arm64: dts: qcom: sm8450: Add qup nodes for qup0
arm64: dts: qcom: sm8450: Add qup nodes for qup1
arm64: dts: qcom: sm8450: Add qup nodes for qup2
arm64: dts: qcom: sm8450: Fix missing iommus for qup1
arm64: dts: qcom: sm8450-qrd: Enable spi and i2c nodes
arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 24 +
arch/arm64/boot/dts/qcom/sm8450.dtsi | 1240 +++++++++++++++++++++++
2 files changed, 1264 insertions(+)
--
2.34.1
qup0 has 7 SEs, with SE7 as uart and already added, so add the
remaining 6 SEs (i2c and spi) along with pinconf for these SEs
Signed-off-by: Vinod Koul <[email protected]>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 412 +++++++++++++++++++++++++++
1 file changed, 412 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 93ff677f0d35..48f8035ea200 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -334,6 +334,25 @@ CLUSTER_PD: cpu-cluster0 {
};
};
+ qup_opp_table_100mhz: qup-100mhz-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-50000000 {
+ opp-hz = /bits/ 64 <50000000>;
+ required-opps = <&rpmhpd_opp_min_svs>;
+ };
+
+ opp-75000000 {
+ opp-hz = /bits/ 64 <75000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+ };
+
reserved_memory: reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
@@ -746,6 +765,292 @@ qupv3_id_0: geniqup@9c0000 {
ranges;
status = "disabled";
+ i2c0: i2c@980000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00980000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c0_data_clk>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi0: spi@980000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00980000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
+ power-domains = <&rpmhpd SM8450_CX>;
+ operating-points-v2 = <&qup_opp_table_100mhz>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@984000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00984000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c1_data_clk>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi1: spi@984000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00984000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@988000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00988000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c2_data_clk>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi2: spi@988000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00988000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+
+ i2c3: i2c@98c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x0098c000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c3_data_clk>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi3: spi@98c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x0098c000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@990000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00990000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c4_data_clk>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi4: spi@990000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00990000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
+ power-domains = <&rpmhpd SM8450_CX>;
+ operating-points-v2 = <&qup_opp_table_100mhz>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@994000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00994000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c5_data_clk>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi5: spi@994000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00994000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+
+ i2c6: i2c@998000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x998000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c6_data_clk>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi6: spi@998000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x998000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 6 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
uart7: serial@99c000 {
compatible = "qcom,geni-debug-uart";
reg = <0 0x0099c000 0 0x4000>;
@@ -1121,6 +1426,41 @@ tlmm: pinctrl@f100000 {
gpio-ranges = <&tlmm 0 0 211>;
wakeup-parent = <&pdc>;
+ qup_i2c0_data_clk: qup-i2c0-data-clk {
+ pins = "gpio0", "gpio1";
+ function = "qup0";
+ };
+
+ qup_i2c1_data_clk: qup-i2c1-data-clk {
+ pins = "gpio4", "gpio5";
+ function = "qup1";
+ };
+
+ qup_i2c2_data_clk: qup-i2c2-data-clk {
+ pins = "gpio8", "gpio9";
+ function = "qup2";
+ };
+
+ qup_i2c3_data_clk: qup-i2c3-data-clk {
+ pins = "gpio12", "gpio13";
+ function = "qup3";
+ };
+
+ qup_i2c4_data_clk: qup-i2c4-data-clk {
+ pins = "gpio16", "gpio17";
+ function = "qup4";
+ };
+
+ qup_i2c5_data_clk: qup-i2c5-data-clk {
+ pins = "gpio206", "gpio207";
+ function = "qup5";
+ };
+
+ qup_i2c6_data_clk: qup-i2c6-data-clk {
+ pins = "gpio20", "gpio21";
+ function = "qup6";
+ };
+
qup_i2c13_data_clk: qup-i2c13-data-clk {
pins = "gpio48", "gpio49";
function = "qup13";
@@ -1135,6 +1475,78 @@ qup_i2c14_data_clk: qup-i2c14-data-clk {
bias-pull-up;
};
+ qup_spi0_cs: qup-spi0-cs {
+ pins = "gpio3";
+ function = "qup0";
+ };
+
+ qup_spi0_data_clk: qup-spi0-data-clk {
+ pins = "gpio0", "gpio1", "gpio2";
+ function = "qup0";
+ };
+
+ qup_spi1_cs: qup-spi1-cs {
+ pins = "gpio7";
+ function = "qup1";
+ };
+
+ qup_spi1_data_clk: qup-spi1-data-clk {
+ pins = "gpio4", "gpio5", "gpio6";
+ function = "qup1";
+ };
+
+ qup_spi2_cs: qup-spi2-cs {
+ pins = "gpio11";
+ function = "qup2";
+ };
+
+ qup_spi2_data_clk: qup-spi2-data-clk {
+ pins = "gpio8", "gpio9", "gpio10";
+ function = "qup2";
+ };
+
+ qup_spi3_cs: qup-spi3-cs {
+ pins = "gpio15";
+ function = "qup3";
+ };
+
+ qup_spi3_data_clk: qup-spi3-data-clk {
+ pins = "gpio12", "gpio13", "gpio14";
+ function = "qup3";
+ };
+
+ qup_spi4_cs: qup-spi4-cs {
+ pins = "gpio19";
+ function = "qup4";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ qup_spi4_data_clk: qup-spi4-data-clk {
+ pins = "gpio16", "gpio17", "gpio18";
+ function = "qup4";
+ };
+
+ qup_spi5_cs: qup-spi5-cs {
+ pins = "gpio85";
+ function = "qup5";
+ };
+
+ qup_spi5_data_clk: qup-spi5-data-clk {
+ pins = "gpio206", "gpio207", "gpio84";
+ function = "qup5";
+ };
+
+ qup_spi6_cs: qup-spi6-cs {
+ pins = "gpio23";
+ function = "qup6";
+ };
+
+ qup_spi6_data_clk: qup-spi6-data-clk {
+ pins = "gpio20", "gpio21", "gpio22";
+ function = "qup6";
+ };
+
qup_uart7_rx: qup-uart7-rx {
pins = "gpio26";
function = "qup7";
--
2.34.1
qup2 has 7 SEs, so add the SEs (i2c and spi) along with pinconf for
these SEs
Signed-off-by: Vinod Koul <[email protected]>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 396 +++++++++++++++++++++++++++
1 file changed, 396 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 3097a6e3ab4e..067568c13448 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -729,6 +729,299 @@ gpi_dma2: dma-controller@800000 {
status = "disabled";
};
+ qupv3_id_2: geniqup@8c0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0x008c0000 0x0 0x2000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
+ iommus = <&apps_smmu 0x483 0x0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ i2c15: i2c@880000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00880000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c15_data_clk>;
+ interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi15: spi@880000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00880000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+ interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
+ spi-max-frequency = <50000000>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+ interconnect-names = "qup-core", "qup-config";
+ dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c16: i2c@884000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00884000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c16_data_clk>;
+ interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi16: spi@884000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00884000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+ interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi16_data_clk>, <&qup_spi16_cs>;
+ spi-max-frequency = <50000000>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+ interconnect-names = "qup-core", "qup-config";
+ dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c17: i2c@888000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00888000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c17_data_clk>;
+ interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi17: spi@888000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00888000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+ interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi17_data_clk>, <&qup_spi17_cs>;
+ spi-max-frequency = <50000000>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+ interconnect-names = "qup-core", "qup-config";
+ dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c18: i2c@88c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x0088c000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c18_data_clk>;
+ interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi18: spi@88c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0088c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+ interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi18_data_clk>, <&qup_spi18_cs>;
+ spi-max-frequency = <50000000>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+ interconnect-names = "qup-core", "qup-config";
+ dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c19: i2c@890000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00890000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c19_data_clk>;
+ interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi19: spi@890000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00890000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+ interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi19_data_clk>, <&qup_spi19_cs>;
+ spi-max-frequency = <50000000>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+ interconnect-names = "qup-core", "qup-config";
+ dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c20: i2c@894000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00894000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c20_data_clk>;
+ interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi20: spi@894000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00894000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+ interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi20_data_clk>, <&qup_spi20_cs>;
+ spi-max-frequency = <50000000>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+ interconnect-names = "qup-core", "qup-config";
+ dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c21: i2c@898000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00898000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c21_data_clk>;
+ interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma2 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma2 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi21: spi@898000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00898000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
+ interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi21_data_clk>, <&qup_spi21_cs>;
+ spi-max-frequency = <50000000>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+ interconnect-names = "qup-core", "qup-config";
+ dmas = <&gpi_dma2 0 6 QCOM_GPI_SPI>,
+ <&gpi_dma2 1 6 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+ };
+
gpi_dma0: dma-controller@900000 {
compatible = "qcom,sm8450-gpi-dma";
#dma-cells = <3>;
@@ -1754,6 +2047,41 @@ qup_i2c14_data_clk: qup-i2c14-data-clk {
bias-pull-up;
};
+ qup_i2c15_data_clk: qup-i2c15-data-clk {
+ pins = "gpio56", "gpio57";
+ function = "qup15";
+ };
+
+ qup_i2c16_data_clk: qup-i2c16-data-clk {
+ pins = "gpio60", "gpio61";
+ function = "qup16";
+ };
+
+ qup_i2c17_data_clk: qup-i2c17-data-clk {
+ pins = "gpio64", "gpio65";
+ function = "qup17";
+ };
+
+ qup_i2c18_data_clk: qup-i2c18-data-clk {
+ pins = "gpio68", "gpio69";
+ function = "qup18";
+ };
+
+ qup_i2c19_data_clk: qup-i2c19-data-clk {
+ pins = "gpio72", "gpio73";
+ function = "qup19";
+ };
+
+ qup_i2c20_data_clk: qup-i2c20-data-clk {
+ pins = "gpio76", "gpio77";
+ function = "qup20";
+ };
+
+ qup_i2c21_data_clk: qup-i2c21-data-clk {
+ pins = "gpio80", "gpio81";
+ function = "qup21";
+ };
+
qup_spi0_cs: qup-spi0-cs {
pins = "gpio3";
function = "qup0";
@@ -1906,6 +2234,74 @@ qup_spi15_data_clk: qup-spi15-data-clk {
function = "qup15";
};
+ qup_spi16_cs: qup-spi16-cs {
+ pins = "gpio63";
+ function = "qup16";
+ };
+
+ qup_spi16_data_clk: qup-spi16-data-clk {
+ pins = "gpio60", "gpio61", "gpio62";
+ function = "qup16";
+ };
+
+ qup_spi17_cs: qup-spi17-cs {
+ pins = "gpio67";
+ function = "qup17";
+ };
+
+ qup_spi17_data_clk: qup-spi17-data-clk {
+ pins = "gpio64", "gpio65", "gpio66";
+ function = "qup17";
+ };
+
+ qup_spi18_cs: qup-spi18-cs {
+ pins = "gpio71";
+ function = "qup18";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ qup_spi18_data_clk: qup-spi18-data-clk {
+ pins = "gpio68", "gpio69", "gpio70";
+ function = "qup18";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ qup_spi19_cs: qup-spi19-cs {
+ pins = "gpio75";
+ function = "qup19";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ qup_spi19_data_clk: qup-spi19-data-clk {
+ pins = "gpio72", "gpio73", "gpio74";
+ function = "qup19";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ qup_spi20_cs: qup-spi20-cs {
+ pins = "gpio79";
+ function = "qup20";
+ };
+
+ qup_spi20_data_clk: qup-spi20-data-clk {
+ pins = "gpio76", "gpio77", "gpio78";
+ function = "qup20";
+ };
+
+ qup_spi21_cs: qup-spi21-cs {
+ pins = "gpio83";
+ function = "qup21";
+ };
+
+ qup_spi21_data_clk: qup-spi21-data-clk {
+ pins = "gpio80", "gpio81", "gpio82";
+ function = "qup21";
+ };
+
qup_uart7_rx: qup-uart7-rx {
pins = "gpio26";
function = "qup7";
--
2.34.1
qupv3_id_0 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.
While at it also add interconnect nodes for qup
Fixes: 5188049c9b36 ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <[email protected]>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 3 +++
1 file changed, 3 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index bfbb6e04fcb4..93ff677f0d35 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -738,6 +738,9 @@ qupv3_id_0: geniqup@9c0000 {
clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ iommus = <&apps_smmu 0x5a3 0x0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>;
+ interconnect-names = "qup-core";
#address-cells = <2>;
#size-cells = <2>;
ranges;
--
2.34.1
Enable the i2c5, spi4, spi18 and spi19 nodes which were tested on qrd
board along with related qup nodes and gpi_dma0
Signed-off-by: Vinod Koul <[email protected]>
---
arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-qrd.dts b/arch/arm64/boot/dts/qcom/sm8450-qrd.dts
index 9526632d4029..1e87a083816e 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-qrd.dts
@@ -342,10 +342,22 @@ vreg_l6e_1p2: ldo6 {
};
};
+&gpi_dma0 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
&qupv3_id_0 {
status = "okay";
};
+&qupv3_id_2 {
+ status = "okay";
+};
+
&remoteproc_adsp {
status = "okay";
firmware-name = "qcom/sm8450/adsp.mbn";
@@ -366,6 +378,18 @@ &remoteproc_slpi {
firmware-name = "qcom/sm8450/slpi.mbn";
};
+&spi4 {
+ status = "okay";
+};
+
+&spi18 {
+ status = "okay";
+};
+
+&spi19 {
+ status = "okay";
+};
+
&tlmm {
gpio-reserved-ranges = <28 4>, <36 4>;
};
--
2.34.1
GPI DMA can be used for DMA operations for QUP devices, so add the three
gpi_dma insances found in this SoC
Signed-off-by: Vinod Koul <[email protected]>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 67 ++++++++++++++++++++++++++++
1 file changed, 67 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 934e29b9e153..bfbb6e04fcb4 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -6,6 +6,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-sm8450.h>
#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/power/qcom-rpmpd.h>
@@ -687,6 +688,50 @@ gcc: clock-controller@100000 {
clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
};
+ gpi_dma2: dma-controller@800000 {
+ compatible = "qcom,sm8450-gpi-dma";
+ #dma-cells = <3>;
+ reg = <0 0x800000 0 0x60000>;
+ interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <12>;
+ dma-channel-mask = <0x7e>;
+ iommus = <&apps_smmu 0x496 0x0>;
+ status = "disabled";
+ };
+
+ gpi_dma0: dma-controller@900000 {
+ compatible = "qcom,sm8450-gpi-dma";
+ #dma-cells = <3>;
+ reg = <0 0x900000 0 0x60000>;
+ interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <12>;
+ dma-channel-mask = <0x7e>;
+ iommus = <&apps_smmu 0x5b6 0x0>;
+ status = "disabled";
+ };
+
qupv3_id_0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x009c0000 0x0 0x2000>;
@@ -712,6 +757,28 @@ uart7: serial@99c000 {
};
};
+ gpi_dma1: dma-controller@a00000 {
+ compatible = "qcom,sm8450-gpi-dma";
+ #dma-cells = <3>;
+ reg = <0 0xa00000 0 0x60000>;
+ interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <12>;
+ dma-channel-mask = <0x7e>;
+ iommus = <&apps_smmu 0x56 0x0>;
+ status = "disabled";
+ };
+
qupv3_id_1: geniqup@ac0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x00ac0000 0x0 0x6000>;
--
2.34.1
qup1 has 7 SEs, I2C13 and I2C14 were already added so added the
remaining SEs (i2c and spi) along with pinconf for these SEs
Also add interconnect properties for I2C13 and I2C14
Signed-off-by: Vinod Koul <[email protected]>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 359 +++++++++++++++++++++++++++
1 file changed, 359 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 48f8035ea200..3097a6e3ab4e 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -1098,6 +1098,206 @@ qupv3_id_1: geniqup@ac0000 {
ranges;
status = "disabled";
+ i2c8: i2c@a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00a80000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c8_data_clk>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi8: spi@a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00a80000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c9: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00a84000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c9_data_clk>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi9: spi@a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00a84000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c10: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00a88000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c10_data_clk>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi10: spi@a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00a88000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c11: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00a8c000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c11_data_clk>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi11: spi@a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00a8c000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c12: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x00a90000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c12_data_clk>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ spi12: spi@a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00a90000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
i2c13: i2c@a94000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00a94000 0 0x4000>;
@@ -1106,6 +1306,33 @@ i2c13: i2c@a94000 {
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c13_data_clk>;
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi13: spi@a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00a94000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1119,6 +1346,33 @@ i2c14: i2c@a98000 {
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c14_data_clk>;
interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi14: spi@a98000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x00a98000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
+ dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 6 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1461,6 +1715,31 @@ qup_i2c6_data_clk: qup-i2c6-data-clk {
function = "qup6";
};
+ qup_i2c8_data_clk: qup-i2c8-data-clk {
+ pins = "gpio28", "gpio29";
+ function = "qup8";
+ };
+
+ qup_i2c9_data_clk: qup-i2c9-data-clk {
+ pins = "gpio32", "gpio33";
+ function = "qup9";
+ };
+
+ qup_i2c10_data_clk: qup-i2c10-data-clk {
+ pins = "gpio36", "gpio37";
+ function = "qup10";
+ };
+
+ qup_i2c11_data_clk: qup-i2c11-data-clk {
+ pins = "gpio40", "gpio41";
+ function = "qup11";
+ };
+
+ qup_i2c12_data_clk: qup-i2c12-data-clk {
+ pins = "gpio44", "gpio45";
+ function = "qup12";
+ };
+
qup_i2c13_data_clk: qup-i2c13-data-clk {
pins = "gpio48", "gpio49";
function = "qup13";
@@ -1547,6 +1826,86 @@ qup_spi6_data_clk: qup-spi6-data-clk {
function = "qup6";
};
+ qup_spi8_cs: qup-spi8-cs {
+ pins = "gpio31";
+ function = "qup8";
+ };
+
+ qup_spi8_data_clk: qup-spi8-data-clk {
+ pins = "gpio28", "gpio29", "gpio30";
+ function = "qup8";
+ };
+
+ qup_spi9_cs: qup-spi9-cs {
+ pins = "gpio35";
+ function = "qup9";
+ };
+
+ qup_spi9_data_clk: qup-spi9-data-clk {
+ pins = "gpio32", "gpio33", "gpio34";
+ function = "qup9";
+ };
+
+ qup_spi10_cs: qup-spi10-cs {
+ pins = "gpio39";
+ function = "qup10";
+ };
+
+ qup_spi10_data_clk: qup-spi10-data-clk {
+ pins = "gpio36", "gpio37", "gpio38";
+ function = "qup10";
+ };
+
+ qup_spi11_cs: qup-spi11-cs {
+ pins = "gpio43";
+ function = "qup11";
+ };
+
+ qup_spi11_data_clk: qup-spi11-data-clk {
+ pins = "gpio40", "gpio41", "gpio42";
+ function = "qup11";
+ };
+
+ qup_spi12_cs: qup-spi12-cs {
+ pins = "gpio47";
+ function = "qup12";
+ };
+
+ qup_spi12_data_clk: qup-spi12-data-clk {
+ pins = "gpio44", "gpio45", "gpio46";
+ function = "qup12";
+ };
+
+ qup_spi13_cs: qup-spi13-cs {
+ pins = "gpio51";
+ function = "qup13";
+ };
+
+ qup_spi13_data_clk: qup-spi13-data-clk {
+ pins = "gpio48", "gpio49", "gpio50";
+ function = "qup13";
+ };
+
+ qup_spi14_cs: qup-spi14-cs {
+ pins = "gpio55";
+ function = "qup14";
+ };
+
+ qup_spi14_data_clk: qup-spi14-data-clk {
+ pins = "gpio52", "gpio53", "gpio54";
+ function = "qup14";
+ };
+
+ qup_spi15_cs: qup-spi15-cs {
+ pins = "gpio59";
+ function = "qup15";
+ };
+
+ qup_spi15_data_clk: qup-spi15-data-clk {
+ pins = "gpio56", "gpio57", "gpio58";
+ function = "qup15";
+ };
+
qup_uart7_rx: qup-uart7-rx {
pins = "gpio26";
function = "qup7";
--
2.34.1
qupv3_id_1 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.
Fixes: 5188049c9b36 ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <[email protected]>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 3 +++
1 file changed, 3 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 067568c13448..88ec7fe455cf 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -1386,6 +1386,9 @@ qupv3_id_1: geniqup@ac0000 {
clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ iommus = <&apps_smmu 0x43 0x0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>;
+ interconnect-names = "qup-core";
#address-cells = <2>;
#size-cells = <2>;
ranges;
--
2.34.1
On Thu, 14 Apr 2022 15:46:23 +0530, Vinod Koul wrote:
> This series adds the gpi_dma nodes followed by the i2c and spi nodes for the
> three qups found in the SM8450 SoC.
>
> While at it, iommus was missing for qup0/qup1, so fix that up too.
>
> Lastly enable the spi and i2c nodes found on the QRD board.
>
> [...]
Applied, thanks!
[1/7] arm64: dts: qcom: sm8450: Add gpi_dma nodes
commit: b9c8433083097327cad19fbf633fb0735a008315
[2/7] arm64: dts: qcom: sm8450: Fix missing iommus for qup
commit: 488922c1a372579bf2caf40933e7459e3c86276f
[3/7] arm64: dts: qcom: sm8450: Add qup nodes for qup0
commit: a84e88e9a00334f1468a9f69a77091dbe80b7a3b
[4/7] arm64: dts: qcom: sm8450: Add qup nodes for qup1
commit: 1a380216fd6fcf7135b2b413bb9431fc98e2fa23
[5/7] arm64: dts: qcom: sm8450: Add qup nodes for qup2
commit: ba640cd31342b45dcf2f95f6ca7dcbc46629919f
[6/7] arm64: dts: qcom: sm8450: Fix missing iommus for qup1
commit: 67ebdc6dd1e2049fd9620f0572bc81a809afbe24
[7/7] arm64: dts: qcom: sm8450-qrd: Enable spi and i2c nodes
commit: d953239726e971ecaee45d86b4bcd605be839b2a
Best regards,
--
Bjorn Andersson <[email protected]>