Introduce the Qualcomm SA8540P ride automotive platform, also known as
Qdrive-3 development board.
This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
regulators, debug UART, PMICs, remoteprocs and USB.
The SA8540P ride contains four PM8450 PMICs. A separate DTSI file has
been created for PMIC, so that it can be used for future SA8540P based
boards.
Signed-off-by: Parikshit Pareek <[email protected]>
Tested-by: Brian Masney <[email protected]>
Reviewed-by: Brian Masney <[email protected]>
Tested-by: Eric Chanudet <[email protected]>
Reviewed-by: Eric Chanudet <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Reviewed-by: Johan Hovold <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/pm8450a.dtsi | 77 ++++++++
arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 217 ++++++++++++++++++++++
3 files changed, 295 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm8450a.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-ride.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index afe496a93f94..87a681f15643 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -56,6 +56,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sa8540p-ride.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1-lte.dtb
diff --git a/arch/arm64/boot/dts/qcom/pm8450a.dtsi b/arch/arm64/boot/dts/qcom/pm8450a.dtsi
new file mode 100644
index 000000000000..34fc72896761
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8450a.dtsi
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pm8450a: pmic@0 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450a_gpios: gpio@c000 {
+ compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ gpio-ranges = <&pm8450a_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8450c: pmic@4 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450c_gpios: gpio@c000 {
+ compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ gpio-ranges = <&pm8450c_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8450e: pmic@8 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x8 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450e_gpios: gpio@c000 {
+ compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ gpio-ranges = <&pm8450e_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8450g: pmic@c {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0xc SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450g_gpios: gpio@c000 {
+ compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ gpio-ranges = <&pm8450g_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
new file mode 100644
index 000000000000..a5f87a8629d6
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sa8540p.dtsi"
+#include "pm8450a.dtsi"
+
+/ {
+ model = "Qualcomm SA8540P Ride";
+ compatible = "qcom,sa8540p-ride", "qcom,sa8540p";
+
+ aliases {
+ serial0 = &qup2_uart17;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_l3a: ldo3 {
+ regulator-name = "vreg_l3a";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1208000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13a: ldo13 {
+ regulator-name = "vreg_l13a";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c: ldo2 {
+ regulator-name = "vreg_l2c";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c: ldo4 {
+ regulator-name = "vreg_l4c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1208000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c: ldo6 {
+ regulator-name = "vreg_l6c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17c: ldo17 {
+ regulator-name = "vreg_l17c";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "g";
+
+ vreg_l3g: ldo3 {
+ regulator-name = "vreg_l3g";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7g: ldo7 {
+ regulator-name = "vreg_l7g";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8g: ldo8 {
+ regulator-name = "vreg_l8g";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&qup2 {
+ status = "okay";
+};
+
+&qup2_uart17 {
+ compatible = "qcom,geni-debug-uart";
+ status = "okay";
+};
+
+&remoteproc_nsp0 {
+ firmware-name = "qcom/sa8540p/cdsp.mbn";
+ status = "okay";
+};
+
+&remoteproc_nsp1 {
+ firmware-name = "qcom/sa8540p/cdsp1.mbn";
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l17c>;
+ vccq-supply = <&vreg_l6c>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l8g>;
+ vdda-pll-supply = <&vreg_l3g>;
+
+ status = "okay";
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_0_dwc3 {
+ dr_mode = "peripheral";
+};
+
+&usb_0_hsphy {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7a>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy {
+ vdda-phy-supply = <&vreg_l3a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy0 {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7g>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy0 {
+ vdda-phy-supply = <&vreg_l3a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
--
2.17.1
On Fri, Nov 18, 2022 at 08:21:58AM +0530, Parikshit Pareek wrote:
> Introduce the Qualcomm SA8540P ride automotive platform, also known as
> Qdrive-3 development board.
>
> This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
> regulators, debug UART, PMICs, remoteprocs and USB.
>
> The SA8540P ride contains four PM8450 PMICs. A separate DTSI file has
> been created for PMIC, so that it can be used for future SA8540P based
> boards.
>
> Signed-off-by: Parikshit Pareek <[email protected]>
> Tested-by: Brian Masney <[email protected]>
> Reviewed-by: Brian Masney <[email protected]>
> Tested-by: Eric Chanudet <[email protected]>
> Reviewed-by: Eric Chanudet <[email protected]>
> Reviewed-by: Konrad Dybcio <[email protected]>
> Reviewed-by: Johan Hovold <[email protected]>
Tested-by: Andrew Halaney <[email protected]>