From: Arınç ÜNAL <[email protected]>
Remove now incorrect comment regarding port 5 as GMAC5. This is supposed to
be supported since commit 38f790a80560 ("net: dsa: mt7530: Add support for
port 5") under mt7530_setup_port5().
Fixes: 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Arınç ÜNAL <[email protected]>
---
drivers/net/dsa/mt7530.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index a508402c4ecb..b1a79460df0e 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2201,7 +2201,7 @@ mt7530_setup(struct dsa_switch *ds)
mt7530_pll_setup(priv);
- /* Enable Port 6 only; P5 as GMAC5 which currently is not supported */
+ /* Enable port 6 */
val = mt7530_read(priv, MT7530_MHWTRAP);
val &= ~MHWTRAP_P6_DIS & ~MHWTRAP_PHY_ACCESS;
val |= MHWTRAP_MANUAL;
--
2.37.2
From: Arınç ÜNAL <[email protected]>
As my testing on the MCM MT7530 switch on MT7621 SoC shows, setting the PLL
frequency does not affect MII modes other than trgmii on port 5 and port 6.
So the assumption is that the operation here called "setting the PLL
frequency" actually sets the frequency of the TRGMII TX clock.
Make it so that it and the rest of the trgmii setup run only when the
trgmii mode is used.
Tested rgmii and trgmii modes of port 6 on MCM MT7530 on MT7621AT Unielec
U7621-06 and standalone MT7530 on MT7623NI Bananapi BPI-R2.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Tested-by: Arınç ÜNAL <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
---
drivers/net/dsa/mt7530.c | 62 ++++++++++++++++++++--------------------
1 file changed, 31 insertions(+), 31 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index b1a79460df0e..c2d81b7a429d 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -430,8 +430,6 @@ mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
switch (interface) {
case PHY_INTERFACE_MODE_RGMII:
trgint = 0;
- /* PLL frequency: 125MHz */
- ncpo1 = 0x0c80;
break;
case PHY_INTERFACE_MODE_TRGMII:
trgint = 1;
@@ -462,38 +460,40 @@ mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
P6_INTF_MODE(trgint));
- /* Lower Tx Driving for TRGMII path */
- for (i = 0 ; i < NUM_TRGMII_CTRL ; i++)
- mt7530_write(priv, MT7530_TRGMII_TD_ODT(i),
- TD_DM_DRVP(8) | TD_DM_DRVN(8));
-
- /* Disable MT7530 core and TRGMII Tx clocks */
- core_clear(priv, CORE_TRGMII_GSW_CLK_CG,
- REG_GSWCK_EN | REG_TRGMIICK_EN);
-
- /* Setup the MT7530 TRGMII Tx Clock */
- core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
- core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
- core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
- core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
- core_write(priv, CORE_PLL_GROUP4,
- RG_SYSPLL_DDSFBK_EN | RG_SYSPLL_BIAS_EN |
- RG_SYSPLL_BIAS_LPF_EN);
- core_write(priv, CORE_PLL_GROUP2,
- RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN |
- RG_SYSPLL_POSDIV(1));
- core_write(priv, CORE_PLL_GROUP7,
- RG_LCDDS_PCW_NCPO_CHG | RG_LCCDS_C(3) |
- RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
-
- /* Enable MT7530 core and TRGMII Tx clocks */
- core_set(priv, CORE_TRGMII_GSW_CLK_CG,
- REG_GSWCK_EN | REG_TRGMIICK_EN);
-
- if (!trgint)
+ if (trgint) {
+ /* Lower Tx Driving for TRGMII path */
+ for (i = 0 ; i < NUM_TRGMII_CTRL ; i++)
+ mt7530_write(priv, MT7530_TRGMII_TD_ODT(i),
+ TD_DM_DRVP(8) | TD_DM_DRVN(8));
+
+ /* Disable MT7530 core and TRGMII Tx clocks */
+ core_clear(priv, CORE_TRGMII_GSW_CLK_CG,
+ REG_GSWCK_EN | REG_TRGMIICK_EN);
+
+ /* Setup the MT7530 TRGMII Tx Clock */
+ core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
+ core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
+ core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
+ core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
+ core_write(priv, CORE_PLL_GROUP4,
+ RG_SYSPLL_DDSFBK_EN | RG_SYSPLL_BIAS_EN |
+ RG_SYSPLL_BIAS_LPF_EN);
+ core_write(priv, CORE_PLL_GROUP2,
+ RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN |
+ RG_SYSPLL_POSDIV(1));
+ core_write(priv, CORE_PLL_GROUP7,
+ RG_LCDDS_PCW_NCPO_CHG | RG_LCCDS_C(3) |
+ RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
+
+ /* Enable MT7530 core and TRGMII Tx clocks */
+ core_set(priv, CORE_TRGMII_GSW_CLK_CG,
+ REG_GSWCK_EN | REG_TRGMIICK_EN);
+ } else {
for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
mt7530_rmw(priv, MT7530_TRGMII_RD(i),
RD_TAP_MASK, RD_TAP(16));
+ }
+
return 0;
}
--
2.37.2
On Wed, 8 Mar 2023 16:07:14 +0300 [email protected] wrote:
> diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
> index a508402c4ecb..b1a79460df0e 100644
> --- a/drivers/net/dsa/mt7530.c
> +++ b/drivers/net/dsa/mt7530.c
> @@ -2201,7 +2201,7 @@ mt7530_setup(struct dsa_switch *ds)
>
> mt7530_pll_setup(priv);
>
> - /* Enable Port 6 only; P5 as GMAC5 which currently is not supported */
> + /* Enable port 6 */
I think you posted before Vladimir's patch went in, so even tho
it applies now the CI/build bot could not test it. Please repost.