The upstream IPA driver now supports IPA v5.0 for SDX65. Add
IPA-related nodes and definitions to "sdx65.dtsi", and enable IPA
in "sdx65-mtp.dts".
Having touched these files, Konrad advised I should update them to
move the "status" property to the end of nodes where it is used.
Version 2 of this series addresses comments made by Krzysztof and
Konrad, and adds their reviewed-by tags.
-Alex
Alex Elder (2):
ARM: dts: qcom: sdx65: add IPA information
ARM: dts: qcom-sdx65: move status properties to end of nodes
arch/arm/boot/dts/qcom-sdx65-mtp.dts | 11 +++++--
arch/arm/boot/dts/qcom-sdx65.dtsi | 47 ++++++++++++++++++++++++++--
2 files changed, 52 insertions(+), 6 deletions(-)
--
2.34.1
Add IPA-related nodes and definitions to "sdx65.dtsi". The SMP2P
nodes (ipa_smp2p_out and ipa_smp2p_in) are already present.
Enable IPA in "sdx65-mtp.dts"; this GSI firmware is loaded by Trust
Zone on this platform.
Reviewed-by: Konrad Dybcio <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Tested-by: Rohit Agarwal <[email protected]>
Signed-off-by: Alex Elder <[email protected]>
---
v2: - Fixed an alignment issue noticed by Krzysztof.
- Moved the "iommus" property as suggested by Konrad.
arch/arm/boot/dts/qcom-sdx65-mtp.dts | 5 ++++
arch/arm/boot/dts/qcom-sdx65.dtsi | 39 ++++++++++++++++++++++++++++
2 files changed, 44 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
index ed98c83c141fc..72e25de0db5fc 100644
--- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
+++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
@@ -245,6 +245,11 @@ &blsp1_uart3 {
status = "okay";
};
+&ipa {
+ qcom,gsi-loader = "skip";
+ status = "okay";
+};
+
&qpic_bam {
status = "okay";
};
diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
index 192f9f94bc8b4..f35061e5b7fb8 100644
--- a/arch/arm/boot/dts/qcom-sdx65.dtsi
+++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/interconnect/qcom,sdx65.h>
/ {
#address-cells = <1>;
@@ -299,6 +300,44 @@ tcsr_mutex: hwlock@1f40000 {
#hwlock-cells = <1>;
};
+ ipa: ipa@3e04000 {
+ compatible = "qcom,sdx65-ipa";
+
+ reg = <0x3f40000 0x10000>,
+ <0x3f50000 0x5000>,
+ <0x3e04000 0xfc000>;
+ reg-names = "ipa-reg",
+ "ipa-shared",
+ "gsi";
+
+ interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
+ <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+ <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "ipa",
+ "gsi",
+ "ipa-clock-query",
+ "ipa-setup-ready";
+
+ iommus = <&apps_smmu 0x5e0 0x0>,
+ <&apps_smmu 0x5e2 0x0>;
+
+ clocks = <&rpmhcc RPMH_IPA_CLK>;
+ clock-names = "core";
+
+ interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI1>,
+ <&mem_noc MASTER_APPSS_PROC &system_noc SLAVE_IPA_CFG>;
+ interconnect-names = "memory",
+ "config";
+
+ qcom,smem-states = <&ipa_smp2p_out 0>,
+ <&ipa_smp2p_out 1>;
+ qcom,smem-state-names = "ipa-clock-enabled-valid",
+ "ipa-clock-enabled";
+
+ status = "disabled";
+ };
+
remoteproc_mpss: remoteproc@4080000 {
compatible = "qcom,sdx55-mpss-pas";
reg = <0x04080000 0x4040>;
--
2.34.1
Move a few device tree "status" properties so that they are the last
specified property, in "qcom-sdx65-mtp.dts" and "qcom-sdx65.dtsi".
Note that properties must always be specified before sub-nodes.
Reviewed-by: Konrad Dybcio <[email protected]>
Suggested-by: Konrad Dybcio <[email protected]>
Signed-off-by: Alex Elder <[email protected]>
---
arch/arm/boot/dts/qcom-sdx65-mtp.dts | 6 +++---
arch/arm/boot/dts/qcom-sdx65.dtsi | 8 +++++---
2 files changed, 8 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
index 72e25de0db5fc..57bc3b03d3aac 100644
--- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
+++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
@@ -270,8 +270,8 @@ nand@0 {
};
&remoteproc_mpss {
- status = "okay";
memory-region = <&mpss_adsp_mem>;
+ status = "okay";
};
&usb {
@@ -283,14 +283,14 @@ &usb_dwc3 {
};
&usb_hsphy {
- status = "okay";
vdda-pll-supply = <&vreg_l4b_0p88>;
vdda33-supply = <&vreg_l10b_3p08>;
vdda18-supply = <&vreg_l5b_1p8>;
+ status = "okay";
};
&usb_qmpphy {
- status = "okay";
vdda-phy-supply = <&vreg_l4b_0p88>;
vdda-pll-supply = <&vreg_l1b_1p2>;
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
index f35061e5b7fb8..2e1d008bccfd8 100644
--- a/arch/arm/boot/dts/qcom-sdx65.dtsi
+++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
@@ -224,16 +224,15 @@ usb_hsphy: phy@ff4000 {
"qcom,usb-snps-hs-7nm-phy";
reg = <0xff4000 0x120>;
#phy-cells = <0>;
- status = "disabled";
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "ref";
resets = <&gcc GCC_QUSB2PHY_BCR>;
+ status = "disabled";
};
usb_qmpphy: phy@ff6000 {
compatible = "qcom,sdx65-qmp-usb3-uni-phy";
reg = <0x00ff6000 0x1c8>;
- status = "disabled";
#address-cells = <1>;
#size-cells = <1>;
ranges;
@@ -247,6 +246,8 @@ usb_qmpphy: phy@ff6000 {
<&gcc GCC_USB3_PHY_BCR>;
reset-names = "phy", "common";
+ status = "disabled";
+
usb_ssphy: phy@ff6200 {
reg = <0x00ff6e00 0x160>,
<0x00ff7000 0x1ec>,
@@ -394,7 +395,6 @@ mem_noc: interconnect@9680000 {
usb: usb@a6f8800 {
compatible = "qcom,sdx65-dwc3", "qcom,dwc3";
reg = <0x0a6f8800 0x400>;
- status = "disabled";
#address-cells = <1>;
#size-cells = <1>;
ranges;
@@ -424,6 +424,8 @@ usb: usb@a6f8800 {
resets = <&gcc GCC_USB30_BCR>;
+ status = "disabled";
+
usb_dwc3: usb@a600000 {
compatible = "snps,dwc3";
reg = <0x0a600000 0xcd00>;
--
2.34.1
On 3/27/23 2:15 PM, Alex Elder wrote:
> The upstream IPA driver now supports IPA v5.0 for SDX65. Add
> IPA-related nodes and definitions to "sdx65.dtsi", and enable IPA
> in "sdx65-mtp.dts".
>
> Having touched these files, Konrad advised I should update them to
> move the "status" property to the end of nodes where it is used.
>
> Version 2 of this series addresses comments made by Krzysztof and
> Konrad, and adds their reviewed-by tags.
I'm sorry but building "dtbs" with this change adds a warning
I had not noticed before.
simple-bus unit address format error
I'll be sending v3 shortly. Sorry for the noise.
-Alex
> -Alex
>
> Alex Elder (2):
> ARM: dts: qcom: sdx65: add IPA information
> ARM: dts: qcom-sdx65: move status properties to end of nodes
>
> arch/arm/boot/dts/qcom-sdx65-mtp.dts | 11 +++++--
> arch/arm/boot/dts/qcom-sdx65.dtsi | 47 ++++++++++++++++++++++++++--
> 2 files changed, 52 insertions(+), 6 deletions(-)
>