Since the required clock is now available, add bluetooth.
Note: Firmware (bts file) from device vendor reroutes tx for some time
during initialisation and later put it back, producing timeouts in
bluetooth initialisation but ignoring that command leads to proper
initialisation.
Signed-off-by: Andreas Kemnade <[email protected]>
---
Depends on: https://lore.kernel.org/linux-omap/[email protected]/T/#u
arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
index 9d2f2d8639496..25b80385dc1f0 100644
--- a/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
@@ -478,10 +478,12 @@ &uart2 {
interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core OMAP4_UART2_RX>;
- /*
- * BT + GPS in WL1283 in WG7500 requiring CLK32KAUDIO of pmic
- * which does not have a driver
- */
+ bluetooth: tiwi {
+ compatible = "ti,wl1283-st";
+ enable-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>; /* GPIO_25 */
+ clocks = <&twl 1>;
+ clock-names = "ext_clock";
+ };
};
&uart3 {
--
2.39.2
On Wed, 27 Sep 2023 09:56:28 +02Krzysztof Kozlowski <[email protected]> wrote:
> On 26/09/2023 22:42, Andreas Kemnade wrote:
> > Since the required clock is now available, add bluetooth.
> >
> > Note: Firmware (bts file) from device vendor reroutes tx for some time
> > during initialisation and later put it back, producing timeouts in
> > bluetooth initialisation but ignoring that command leads to proper
> > initialisation.
> >
> > Signed-off-by: Andreas Kemnade <[email protected]>
> > ---
> > Depends on: https://lore.kernel.org/linux-omap/[email protected]/T/#u
> > arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts | 10 ++++++----
> > 1 file changed, 6 insertions(+), 4 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
> > index 9d2f2d8639496..25b80385dc1f0 100644
> > --- a/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
> > +++ b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
> > @@ -478,10 +478,12 @@ &uart2 {
> > interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
> > &omap4_pmx_core OMAP4_UART2_RX>;
> >
> > - /*
> > - * BT + GPS in WL1283 in WG7500 requiring CLK32KAUDIO of pmic
> > - * which does not have a driver
> > - */
> > + bluetooth: tiwi {
>
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>
> E.g. "bluetooth"
>
well, that is what I get currently as a reward from the kernel for describing
the hardware and so the motivation for the patch, not necessarily the most important
functionality.
But the over the uart runs the ti shared transport protocol (also there is
a non dt compatible driver in drivers/misc/ti-st) which provides more than Bluetooth,
e.g. it also provides at least GNSS and FM (although it do not know if it works in this particular
hardware). GPS/GNSS should work.
So the node name would be bluetoothgnss then? Well, I think we do not need the label then.
Regards,
Andreas
On 26/09/2023 22:42, Andreas Kemnade wrote:
> Since the required clock is now available, add bluetooth.
>
> Note: Firmware (bts file) from device vendor reroutes tx for some time
> during initialisation and later put it back, producing timeouts in
> bluetooth initialisation but ignoring that command leads to proper
> initialisation.
>
> Signed-off-by: Andreas Kemnade <[email protected]>
> ---
> Depends on: https://lore.kernel.org/linux-omap/[email protected]/T/#u
> arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts | 10 ++++++----
> 1 file changed, 6 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
> index 9d2f2d8639496..25b80385dc1f0 100644
> --- a/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
> +++ b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
> @@ -478,10 +478,12 @@ &uart2 {
> interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
> &omap4_pmx_core OMAP4_UART2_RX>;
>
> - /*
> - * BT + GPS in WL1283 in WG7500 requiring CLK32KAUDIO of pmic
> - * which does not have a driver
> - */
> + bluetooth: tiwi {
Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
E.g. "bluetooth"
Best regards,
Krzysztof
On 27/09/2023 18:29, Andreas Kemnade wrote:
>
>
> On Wed, 27 Sep 2023 09:56:28 +02Krzysztof Kozlowski <[email protected]> wrote:
>
>> On 26/09/2023 22:42, Andreas Kemnade wrote:
>>> Since the required clock is now available, add bluetooth.
>>>
>>> Note: Firmware (bts file) from device vendor reroutes tx for some time
>>> during initialisation and later put it back, producing timeouts in
>>> bluetooth initialisation but ignoring that command leads to proper
>>> initialisation.
>>>
>>> Signed-off-by: Andreas Kemnade <[email protected]>
>>> ---
>>> Depends on: https://lore.kernel.org/linux-omap/[email protected]/T/#u
>>> arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts | 10 ++++++----
>>> 1 file changed, 6 insertions(+), 4 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
>>> index 9d2f2d8639496..25b80385dc1f0 100644
>>> --- a/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
>>> +++ b/arch/arm/boot/dts/ti/omap/omap4-epson-embt2ws.dts
>>> @@ -478,10 +478,12 @@ &uart2 {
>>> interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
>>> &omap4_pmx_core OMAP4_UART2_RX>;
>>>
>>> - /*
>>> - * BT + GPS in WL1283 in WG7500 requiring CLK32KAUDIO of pmic
>>> - * which does not have a driver
>>> - */
>>> + bluetooth: tiwi {
>>
>> Node names should be generic. See also an explanation and list of
>> examples (not exhaustive) in DT specification:
>> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
>>
>> E.g. "bluetooth"
>>
> well, that is what I get currently as a reward from the kernel for describing
> the hardware and so the motivation for the patch, not necessarily the most important
> functionality.
>
> But the over the uart runs the ti shared transport protocol (also there is
> a non dt compatible driver in drivers/misc/ti-st) which provides more than Bluetooth,
> e.g. it also provides at least GNSS and FM (although it do not know if it works in this particular
> hardware). GPS/GNSS should work.
>
> So the node name would be bluetoothgnss then? Well, I think we do not need the label then.
bluetooth-gnss would work for me if it was accepted by bindings... but
it is not, so this leaves you so far with "bluetooth".
Best regards,
Krzysztof