2023-10-04 14:57:18

by Duje Mihanović

Subject: [PATCH RFC v5 2/6] ARM: pxa: Convert Spitz LEDs to GPIO descriptors

Sharp's Spitz board still uses the legacy GPIO interface for configuring
its two onboard LEDs.

Convert them to use the GPIO descriptor interface.

Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Duje Mihanović <[email protected]>
---
arch/arm/mach-pxa/spitz.c | 18 ++++++++++++++++--
1 file changed, 16 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 535e2b2e997b..b6a4085e9fb0 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -452,16 +452,25 @@ static inline void spitz_keys_init(void) {}
* LEDs
******************************************************************************/
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+static struct gpiod_lookup_table spitz_led_gpio_table = {
+ .dev_id = "leds-gpio",
+ .table = {
+ GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_ORANGE, NULL, 0,
+ GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_GREEN, NULL, 1,
+ GPIO_ACTIVE_HIGH),
+ { }
+ }
+};
+
static struct gpio_led spitz_gpio_leds[] = {
{
.name = "spitz:amber:charge",
.default_trigger = "sharpsl-charge",
- .gpio = SPITZ_GPIO_LED_ORANGE,
},
{
.name = "spitz:green:hddactivity",
.default_trigger = "disk-activity",
- .gpio = SPITZ_GPIO_LED_GREEN,
},
};

@@ -480,7 +489,12 @@ static struct platform_device spitz_led_device = {

static void __init spitz_leds_init(void)
{
+ gpiod_add_lookup_table(&spitz_led_gpio_table);
platform_device_register(&spitz_led_device);
+ spitz_gpio_leds[0].gpiod = gpiod_get_index(&spitz_led_device.dev,
+ NULL, 0, GPIOD_ASIS);
+ spitz_gpio_leds[1].gpiod = gpiod_get_index(&spitz_led_device.dev,
+ NULL, 1, GPIOD_ASIS);
}
#else
static inline void spitz_leds_init(void) {}

--
2.42.0

2023-10-06 06:51:09

by Bartosz Golaszewski

Subject: Re: [PATCH RFC v5 2/6] ARM: pxa: Convert Spitz LEDs to GPIO descriptors

On Wed, Oct 4, 2023 at 4:56 PM Duje Mihanović <[email protected]> wrote:
>
> Sharp's Spitz board still uses the legacy GPIO interface for configuring
> its two onboard LEDs.
>
> Convert them to use the GPIO descriptor interface.
>
> Reviewed-by: Linus Walleij <[email protected]>
> Signed-off-by: Duje Mihanović <[email protected]>
> ---
> arch/arm/mach-pxa/spitz.c | 18 ++++++++++++++++--
> 1 file changed, 16 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
> index 535e2b2e997b..b6a4085e9fb0 100644
> --- a/arch/arm/mach-pxa/spitz.c
> +++ b/arch/arm/mach-pxa/spitz.c
> @@ -452,16 +452,25 @@ static inline void spitz_keys_init(void) {}
> * LEDs
> ******************************************************************************/
> #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
> +static struct gpiod_lookup_table spitz_led_gpio_table = {
> + .dev_id = "leds-gpio",
> + .table = {
> + GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_ORANGE, NULL, 0,
> + GPIO_ACTIVE_HIGH),
> + GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_GREEN, NULL, 1,
> + GPIO_ACTIVE_HIGH),
> + { }
> + }
> +};
> +
> static struct gpio_led spitz_gpio_leds[] = {
> {
> .name = "spitz:amber:charge",
> .default_trigger = "sharpsl-charge",
> - .gpio = SPITZ_GPIO_LED_ORANGE,
> },
> {
> .name = "spitz:green:hddactivity",
> .default_trigger = "disk-activity",
> - .gpio = SPITZ_GPIO_LED_GREEN,
> },
> };
>
> @@ -480,7 +489,12 @@ static struct platform_device spitz_led_device = {
>
> static void __init spitz_leds_init(void)
> {
> + gpiod_add_lookup_table(&spitz_led_gpio_table);
> platform_device_register(&spitz_led_device);
> + spitz_gpio_leds[0].gpiod = gpiod_get_index(&spitz_led_device.dev,
> + NULL, 0, GPIOD_ASIS);
> + spitz_gpio_leds[1].gpiod = gpiod_get_index(&spitz_led_device.dev,
> + NULL, 1, GPIOD_ASIS);

You're not using the con_id you specified in the lookup table. How
about using gpiod_get_array()?

Bart

> }
> #else
> static inline void spitz_leds_init(void) {}
>
> --
> 2.42.0
>
>