Hi,
Still not complete, but most of audio support.
Dependency
=========
Depends on:
https://lore.kernel.org/linux-arm-msm/[email protected]/
Bindings were already applied.
Cc: Abel Vesa <[email protected]>
Best regards,
Krzysztof
Krzysztof Kozlowski (4):
arm64: dts: qcom: x1e80100: add ADSP audio codec macros
arm64: dts: qcom: x1e80100: add Soundwire controllers
arm64: dts: qcom: x1e80100-crd: add WCD9385 Audio Codec
arm64: dts: qcom: x1e80100-crd: add WSA8845 speakers
arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 132 +++++++++
arch/arm64/boot/dts/qcom/x1e80100.dtsi | 311 ++++++++++++++++++++++
2 files changed, 443 insertions(+)
--
2.34.1
Add nodes for four WSA8845 speakers. Unlike previous boards like
SM8550-QRD, this board has four speakers spread over two Soundwire buses
instead of two speakers on one bus. Each pair of speakers shares the
reset GPIO thus pinctrl property is only in one of them.
Cc: Abel Vesa <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 76 +++++++++++++++++++++++
1 file changed, 76 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
index aa5c4199bd2c..8b4e5577048a 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
@@ -543,6 +543,24 @@ touchscreen@10 {
};
};
+&lpass_tlmm {
+ spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
+ spkr_23_sd_n_active: spkr-23-sd-n-active-state {
+ pins = "gpio13";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
&mdss {
status = "okay";
};
@@ -633,6 +651,35 @@ &remoteproc_cdsp {
status = "okay";
};
+&swr0 {
+ status = "okay";
+
+ /* WSA8845, Left Woofer */
+ left_woofer: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ pinctrl-0 = <&spkr_01_sd_n_active>;
+ pinctrl-names = "default";
+ powerdown-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "WooferLeft";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ };
+
+ /* WSA8845, Left Tweeter */
+ left_tweeter: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ /* pinctrl in left_woofer node because of sharing the GPIO*/
+ powerdown-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TwitterLeft";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ };
+};
+
&swr1 {
status = "okay";
@@ -655,6 +702,35 @@ wcd_tx: codec@0,3 {
};
};
+&swr3 {
+ status = "okay";
+
+ /* WSA8845, Right Woofer */
+ right_woofer: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ pinctrl-0 = <&spkr_23_sd_n_active>;
+ pinctrl-names = "default";
+ powerdown-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "WooferRight";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ };
+
+ /* WSA8845, Right Tweeter */
+ right_tweeter: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ /* pinctrl in right_woofer node because of sharing the GPIO*/
+ powerdown-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TwitterRight";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ };
+};
+
&tlmm {
gpio-reserved-ranges = <34 2>, /* Unused */
<44 4>, /* SPI (TPM) */
--
2.34.1
Add nodes for LPASS Soundwire v2.0.0 controllers. Difference against
SM8550:
1. Update port configs to match reference implementation,
2. LPASS TLMM GPIO14 is not used as WCD_SR_TX_DATA2 pin but as GPIO
(camera).
Cc: Abel Vesa <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
arch/arm64/boot/dts/qcom/x1e80100.dtsi | 226 +++++++++++++++++++++++++
1 file changed, 226 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 8bc6e544bbc9..262ff4700194 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -2999,6 +2999,36 @@ lpass_wsa2macro: codec@6aa0000 {
sound-name-prefix = "WSA2";
};
+ swr3: soundwire@6ab0000 {
+ compatible = "qcom,soundwire-v2.0.0";
+ reg = <0 0x06ab0000 0 0x10000>;
+ clocks = <&lpass_wsa2macro>;
+ clock-names = "iface";
+ interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
+ label = "WSA2";
+
+ pinctrl-0 = <&wsa2_swr_active>;
+ pinctrl-names = "default";
+
+ qcom,din-ports = <4>;
+ qcom,dout-ports = <9>;
+
+ qcom,ports-sinterval = /bits/ 16 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0xc8 0xff 0xff 0x0f 0x0f 0xff 0x31f>;
+ qcom,ports-offset1 = /bits/ 8 <0x01 0x03 0x05 0x02 0x04 0x15 0x00 0xff 0xff 0x06 0x0d 0xff 0x00>;
+ qcom,ports-offset2 = /bits/ 8 <0xff 0x07 0x1f 0xff 0x07 0x1f 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
+ qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x18>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0x00 0x01 0x01 0x00 0x01 0x01 0x00 0x00 0x00 0x01 0x01 0x00 0x00>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ status = "disabled";
+ };
+
lpass_rxmacro: codec@6ac0000 {
compatible = "qcom,x1e80100-lpass-rx-macro", "qcom,sm8550-lpass-rx-macro";
reg = <0 0x06ac0000 0 0x1000>;
@@ -3016,6 +3046,36 @@ lpass_rxmacro: codec@6ac0000 {
#sound-dai-cells = <1>;
};
+ swr1: soundwire@6ad0000 {
+ compatible = "qcom,soundwire-v2.0.0";
+ reg = <0 0x06ad0000 0 0x10000>;
+ clocks = <&lpass_rxmacro>;
+ clock-names = "iface";
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+ label = "RX";
+
+ pinctrl-0 = <&rx_swr_active>;
+ pinctrl-names = "default";
+
+ qcom,din-ports = <1>;
+ qcom,dout-ports = <11>;
+
+ qcom,ports-sinterval = /bits/ 16 <0x03 0x1f 0x1f 0x07 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x01 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0x03 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0x06 0x0f 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xff 0x00 0x01 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ status = "disabled";
+ };
+
lpass_txmacro: codec@6ae0000 {
compatible = "qcom,x1e80100-lpass-tx-macro", "qcom,sm8550-lpass-tx-macro";
reg = <0 0x06ae0000 0 0x1000>;
@@ -3051,6 +3111,68 @@ lpass_wsamacro: codec@6b00000 {
sound-name-prefix = "WSA";
};
+ swr0: soundwire@6b10000 {
+ compatible = "qcom,soundwire-v2.0.0";
+ reg = <0 0x06b10000 0 0x10000>;
+ clocks = <&lpass_wsamacro>;
+ clock-names = "iface";
+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+ label = "WSA";
+
+ pinctrl-0 = <&wsa_swr_active>;
+ pinctrl-names = "default";
+
+ qcom,din-ports = <4>;
+ qcom,dout-ports = <9>;
+
+ qcom,ports-sinterval = /bits/ 16 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0xc8 0xff 0xff 0x0f 0x0f 0xff 0x31f>;
+ qcom,ports-offset1 = /bits/ 8 <0x01 0x03 0x05 0x02 0x04 0x15 0x00 0xff 0xff 0x06 0x0d 0xff 0x00>;
+ qcom,ports-offset2 = /bits/ 8 <0xff 0x07 0x1f 0xff 0x07 0x1f 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
+ qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x18>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0x00 0x01 0x01 0x00 0x01 0x01 0x00 0x00 0x00 0x01 0x01 0x00 0x00>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ status = "disabled";
+ };
+
+ swr2: soundwire@6d30000 {
+ compatible = "qcom,soundwire-v2.0.0";
+ reg = <0 0x06d30000 0 0x10000>;
+ clocks = <&lpass_txmacro>;
+ clock-names = "iface";
+ interrupts = <GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "core", "wakeup";
+ label = "TX";
+
+ pinctrl-0 = <&tx_swr_active>;
+ pinctrl-names = "default";
+
+ qcom,din-ports = <4>;
+ qcom,dout-ports = <1>;
+
+ qcom,ports-sinterval-low = /bits/ 8 <0x00 0x01 0x03 0x03 0x00>;
+ qcom,ports-offset1 = /bits/ 8 <0x00 0x01 0x02 0x00 0x00>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00 0x00 0xff>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-lane-control = /bits/ 8 <0xff 0x00 0x00 0x01 0xff>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ status = "disabled";
+ };
+
lpass_vamacro: codec@6d44000 {
compatible = "qcom,x1e80100-lpass-va-macro", "qcom,sm8550-lpass-va-macro";
reg = <0 0x06d44000 0 0x1000>;
@@ -3078,6 +3200,110 @@ lpass_tlmm: pinctrl@6e80000 {
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&lpass_tlmm 0 0 23>;
+
+ tx_swr_active: tx-swr-active-state {
+ clk-pins {
+ pins = "gpio0";
+ function = "swr_tx_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio1", "gpio2";
+ function = "swr_tx_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ rx_swr_active: rx-swr-active-state {
+ clk-pins {
+ pins = "gpio3";
+ function = "swr_rx_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio4", "gpio5";
+ function = "swr_rx_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ dmic01_default: dmic01-default-state {
+ clk-pins {
+ pins = "gpio6";
+ function = "dmic1_clk";
+ drive-strength = <8>;
+ output-high;
+ };
+
+ data-pins {
+ pins = "gpio7";
+ function = "dmic1_data";
+ drive-strength = <8>;
+ input-enable;
+ };
+ };
+
+ dmic02_default: dmic02-default-state {
+ clk-pins {
+ pins = "gpio8";
+ function = "dmic2_clk";
+ drive-strength = <8>;
+ output-high;
+ };
+
+ data-pins {
+ pins = "gpio9";
+ function = "dmic2_data";
+ drive-strength = <8>;
+ input-enable;
+ };
+ };
+
+ wsa_swr_active: wsa-swr-active-state {
+ clk-pins {
+ pins = "gpio10";
+ function = "wsa_swr_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio11";
+ function = "wsa_swr_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ wsa2_swr_active: wsa2-swr-active-state {
+ clk-pins {
+ pins = "gpio15";
+ function = "wsa2_swr_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio16";
+ function = "wsa2_swr_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
};
lpass_ag_noc: interconnect@7e40000 {
--
2.34.1
Add Qualcomm Aqstic WCD9385 audio codec on two Soundwire interfaces: RX
and TX.
Cc: Abel Vesa <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 56 +++++++++++++++++++++++
1 file changed, 56 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
index 4f7f83d49847..aa5c4199bd2c 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
@@ -18,6 +18,32 @@ aliases {
serial0 = &uart21;
};
+ audio-codec {
+ compatible = "qcom,wcd9385-codec";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcd_default>;
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+ vdd-buck-supply = <&vreg_l15b_1p8>;
+ vdd-rxtx-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l15b_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob1>;
+
+ #sound-dai-cells = <1>;
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
@@ -607,6 +633,28 @@ &remoteproc_cdsp {
status = "okay";
};
+&swr1 {
+ status = "okay";
+
+ /* WCD9385 RX */
+ wcd_rx: codec@0,4 {
+ compatible = "sdw20217010d00";
+ reg = <0 4>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr2 {
+ status = "okay";
+
+ /* WCD9385 TX */
+ wcd_tx: codec@0,3 {
+ compatible = "sdw20217010d00";
+ reg = <0 3>;
+ qcom,tx-port-mapping = <1 1 2 3>;
+ };
+};
+
&tlmm {
gpio-reserved-ranges = <34 2>, /* Unused */
<44 4>, /* SPI (TPM) */
@@ -649,6 +697,14 @@ reset-n-pins {
drive-strength = <16>;
};
};
+
+ wcd_default: wcd-reset-n-active-state {
+ pins = "gpio191";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
};
&uart21 {
--
2.34.1
On Thu, 14 Dec 2023 14:10:12 +0100, Krzysztof Kozlowski wrote:
> Still not complete, but most of audio support.
>
> Dependency
> =========
> Depends on:
> https://lore.kernel.org/linux-arm-msm/[email protected]/
>
> [...]
Applied, thanks!
[1/4] arm64: dts: qcom: x1e80100: add ADSP audio codec macros
commit: c6d6df1703d47c693e8f44b086f902108d22d0a2
[2/4] arm64: dts: qcom: x1e80100: add Soundwire controllers
commit: 641a7e7e97b6cf657ae4b04a4d19c270a776697d
[3/4] arm64: dts: qcom: x1e80100-crd: add WCD9385 Audio Codec
commit: 229c9ce0fd1168fb5e48ab1729e81dd06c4029f7
[4/4] arm64: dts: qcom: x1e80100-crd: add WSA8845 speakers
commit: 0293019c6709c707cb34382d7e745cf636f39baf
Best regards,
--
Bjorn Andersson <[email protected]>