This patchset extends the Broadcom SATA PHY driver to add
support for Stingray SATA PHY.
All patches are based on Linux-4.12-rc2.
Srinath Mannam (2):
dt-bindings: Update documentation for stingray SATA phy
phy: Add stingray SATA phy support
.../devicetree/bindings/phy/brcm-sata-phy.txt | 7 ++-
drivers/phy/phy-brcm-sata.c | 73 ++++++++++++++++++++++
2 files changed, 77 insertions(+), 3 deletions(-)
--
2.7.4
This patch adds support for stingray SATA phy in the
SATA BRCM phy driver.
Signed-off-by: Srinath Mannam <[email protected]>
---
drivers/phy/phy-brcm-sata.c | 73 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 73 insertions(+)
diff --git a/drivers/phy/phy-brcm-sata.c b/drivers/phy/phy-brcm-sata.c
index ccbc3d9..e6544c8 100644
--- a/drivers/phy/phy-brcm-sata.c
+++ b/drivers/phy/phy-brcm-sata.c
@@ -46,6 +46,7 @@ enum brcm_sata_phy_version {
BRCM_SATA_PHY_STB_40NM,
BRCM_SATA_PHY_IPROC_NS2,
BRCM_SATA_PHY_IPROC_NSP,
+ BRCM_SATA_PHY_IPROC_SR,
};
struct brcm_sata_port {
@@ -81,12 +82,17 @@ enum sata_phy_regs {
PLL_ACTRL2 = 0x8b,
PLL_ACTRL2_SELDIV_MASK = 0x1f,
PLL_ACTRL2_SELDIV_SHIFT = 9,
+ PLL_ACTRL6 = 0x86,
PLL1_REG_BANK = 0x060,
PLL1_ACTRL2 = 0x82,
PLL1_ACTRL3 = 0x83,
PLL1_ACTRL4 = 0x84,
+ TX_REG_BANK = 0x070,
+ TX_ACTRL0 = 0x80,
+ TX_ACTRL0_TXPOL_FLIP = BIT(6),
+
OOB_REG_BANK = 0x150,
OOB1_REG_BANK = 0x160,
OOB_CTRL1 = 0x80,
@@ -347,6 +353,68 @@ static int brcm_nsp_sata_init(struct brcm_sata_port *port)
return 0;
}
+/* SR PHY PLL0 registers */
+#define SR_PLL0_ACTRL6_MAGIC 0xa
+
+/* SR PHY PLL1 registers */
+#define SR_PLL1_ACTRL2_MAGIC 0x32
+#define SR_PLL1_ACTRL3_MAGIC 0x2
+#define SR_PLL1_ACTRL4_MAGIC 0x3e8
+
+static int brcm_sr_sata_init(struct brcm_sata_port *port)
+{
+ struct brcm_sata_phy *priv = port->phy_priv;
+ struct device *dev = port->phy_priv->dev;
+ void __iomem *base = priv->phy_base;
+ unsigned int val, try;
+
+ /* Configure PHY PLL register bank 1 */
+ val = SR_PLL1_ACTRL2_MAGIC;
+ brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val);
+ val = SR_PLL1_ACTRL3_MAGIC;
+ brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val);
+ val = SR_PLL1_ACTRL4_MAGIC;
+ brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val);
+
+ /* Configure PHY PLL register bank 0 */
+ val = SR_PLL0_ACTRL6_MAGIC;
+ brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_ACTRL6, 0x0, val);
+
+ /* Wait for PHY PLL lock by polling pll_lock bit */
+ try = 50;
+ do {
+ val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
+ BLOCK0_XGXSSTATUS);
+ if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
+ break;
+ msleep(20);
+ try--;
+ } while (try);
+
+ if ((val & BLOCK0_XGXSSTATUS_PLL_LOCK) == 0) {
+ /* PLL did not lock; give up */
+ dev_err(dev, "port%d PLL did not lock\n", port->portnum);
+ return -ETIMEDOUT;
+ }
+
+ /* Invert Tx polarity */
+ brcm_sata_phy_wr(base, TX_REG_BANK, TX_ACTRL0,
+ ~TX_ACTRL0_TXPOL_FLIP, TX_ACTRL0_TXPOL_FLIP);
+
+ /* Configure OOB control to handle 100MHz reference clock */
+ val = ((0xc << OOB_CTRL1_BURST_MAX_SHIFT) |
+ (0x4 << OOB_CTRL1_BURST_MIN_SHIFT) |
+ (0x8 << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT) |
+ (0x3 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT));
+ brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL1, 0x0, val);
+ val = ((0x1b << OOB_CTRL2_RESET_IDLE_MAX_SHIFT) |
+ (0x2 << OOB_CTRL2_BURST_CNT_SHIFT) |
+ (0x9 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT));
+ brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL2, 0x0, val);
+
+ return 0;
+}
+
static int brcm_sata_phy_init(struct phy *phy)
{
int rc;
@@ -363,6 +431,9 @@ static int brcm_sata_phy_init(struct phy *phy)
case BRCM_SATA_PHY_IPROC_NSP:
rc = brcm_nsp_sata_init(port);
break;
+ case BRCM_SATA_PHY_IPROC_SR:
+ rc = brcm_sr_sata_init(port);
+ break;
default:
rc = -ENODEV;
}
@@ -384,6 +455,8 @@ static const struct of_device_id brcm_sata_phy_of_match[] = {
.data = (void *)BRCM_SATA_PHY_IPROC_NS2 },
{ .compatible = "brcm,iproc-nsp-sata-phy",
.data = (void *)BRCM_SATA_PHY_IPROC_NSP },
+ { .compatible = "brcm,iproc-sr-sata-phy",
+ .data = (void *)BRCM_SATA_PHY_IPROC_SR },
{},
};
MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match);
--
2.7.4
Update BRCM SATA phy dt-binding documentation for stingray.
Signed-off-by: Srinath Mannam <[email protected]>
Reviewed-by: Ray Jui <[email protected]>
Reviewed-by: Scott Branden <[email protected]>
---
Documentation/devicetree/bindings/phy/brcm-sata-phy.txt | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt
index 6ccce09..97977cd 100644
--- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt
+++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt
@@ -7,12 +7,13 @@ Required properties:
"brcm,iproc-ns2-sata-phy"
"brcm,iproc-nsp-sata-phy"
"brcm,phy-sata3"
+ "brcm,iproc-sr-sata-phy"
- address-cells: should be 1
- size-cells: should be 0
- reg: register ranges for the PHY PCB interface
- reg-names: should be "phy" and "phy-ctrl"
The "phy-ctrl" registers are only required for
- "brcm,iproc-ns2-sata-phy".
+ "brcm,iproc-ns2-sata-phy" and "brcm,iproc-sr-sata-phy".
Sub-nodes:
Each port's PHY should be represented as a sub-node.
@@ -23,8 +24,8 @@ Sub-nodes required properties:
Sub-nodes optional properties:
- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port
- This property is not applicable for "brcm,iproc-ns2-sata-phy" and
- "brcm,iproc-nsp-sata-phy".
+ This property is not applicable for "brcm,iproc-ns2-sata-phy",
+ "brcm,iproc-nsp-sata-phy" and "brcm,iproc-sr-sata-phy".
Example:
sata-phy@f0458100 {
--
2.7.4
On 06/05/2017 02:00 AM, Srinath Mannam wrote:
> Update BRCM SATA phy dt-binding documentation for stingray.
>
> Signed-off-by: Srinath Mannam <[email protected]>
> Reviewed-by: Ray Jui <[email protected]>
> Reviewed-by: Scott Branden <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
--
Florian
On 06/05/2017 02:00 AM, Srinath Mannam wrote:
> This patch adds support for stingray SATA phy in the
> SATA BRCM phy driver.
>
> Signed-off-by: Srinath Mannam <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
--
Florian
On Monday 05 June 2017 02:30 PM, Srinath Mannam wrote:
> This patchset extends the Broadcom SATA PHY driver to add
> support for Stingray SATA PHY.
Please rebase the series to linux-phy -next.
Thanks
Kishon
>
> All patches are based on Linux-4.12-rc2.
>
> Srinath Mannam (2):
> dt-bindings: Update documentation for stingray SATA phy
> phy: Add stingray SATA phy support
>
> .../devicetree/bindings/phy/brcm-sata-phy.txt | 7 ++-
> drivers/phy/phy-brcm-sata.c | 73 ++++++++++++++++++++++
> 2 files changed, 77 insertions(+), 3 deletions(-)
>