As per MADT specification, it's perfectly valid firmware can pass
MADT table to OS with disabled GICC entries. ARM64-SMP code skips
those cpu cores to bring online. However the current GICv3 driver
probe bails out in this case on systems where redistributor regions
are not in the always-on power domain.
This patch does the two things to fix the panic.
- Don't return an error in gic_acpi_match_gicc() for disabled GICC.
- No need to keep GICR region information for disabled GICC.
Kernel crash traces:
Kernel panic - not syncing: No interrupt controller found.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.5 #26
[<ffff000008087770>] dump_backtrace+0x0/0x218
[<ffff0000080879dc>] show_stack+0x14/0x20
[<ffff00000883b078>] dump_stack+0x98/0xb8
[<ffff0000080c5c14>] panic+0x118/0x26c
[<ffff000008b62348>] init_IRQ+0x24/0x2c
[<ffff000008b609fc>] start_kernel+0x230/0x394
[<ffff000008b601e4>] __primary_switched+0x64/0x6c
---[ end Kernel panic - not syncing: No interrupt controller found.
Disabled GICC subtable example:
Subtable Type : 0B [Generic Interrupt Controller]
Length : 50
Reserved : 0000
CPU Interface Number : 0000003D
Processor UID : 0000003D
Flags (decoded below) : 00000000
Processor Enabled : 0
Performance Interrupt Trig Mode : 0
Virtual GIC Interrupt Trig Mode : 0
Parking Protocol Version : 00000000
Performance Interrupt : 00000017
Parked Address : 0000000000000000
Base Address : 0000000000000000
Virtual GIC Base Address : 0000000000000000
Hypervisor GIC Base Address : 0000000000000000
Virtual GIC Interrupt : 00000019
Redistributor Base Address : 0000FFFF88F40000
ARM MPIDR : 000000000000000D
Efficiency Class : 00
Reserved : 000000
Signed-off-by: Shanker Donthineni <[email protected]>
---
drivers/irqchip/irq-gic-v3.c | 14 +++++++++-----
1 file changed, 9 insertions(+), 5 deletions(-)
diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c
index b56c3e2..a30fbac 100644
--- a/drivers/irqchip/irq-gic-v3.c
+++ b/drivers/irqchip/irq-gic-v3.c
@@ -1331,6 +1331,10 @@ static int __init gic_of_init(struct device_node *node, struct device_node *pare
u32 size = reg == GIC_PIDR2_ARCH_GICv4 ? SZ_64K * 4 : SZ_64K * 2;
void __iomem *redist_base;
+ /* GICC entry which has !ACPI_MADT_ENABLED is not unusable so skip */
+ if (!(gicc->flags & ACPI_MADT_ENABLED))
+ return 0;
+
redist_base = ioremap(gicc->gicr_base_address, size);
if (!redist_base)
return -ENOMEM;
@@ -1374,13 +1378,13 @@ static int __init gic_acpi_match_gicc(struct acpi_subtable_header *header,
(struct acpi_madt_generic_interrupt *)header;
/*
- * If GICC is enabled and has valid gicr base address, then it means
- * GICR base is presented via GICC
+ * If GICC is enabled and has not valid gicr base address, then it means
+ * GICR base is not presented via GICC
*/
- if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
- return 0;
+ if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
+ return -ENODEV;
- return -ENODEV;
+ return 0;
}
static int __init gic_acpi_count_gicr_regions(void)
--
Qualcomm Datacenter Technologies, Inc. on behalf of the Qualcomm Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
On 03/12/17 23:21, Shanker Donthineni wrote:
> As per MADT specification, it's perfectly valid firmware can pass
> MADT table to OS with disabled GICC entries. ARM64-SMP code skips
> those cpu cores to bring online. However the current GICv3 driver
> probe bails out in this case on systems where redistributor regions
> are not in the always-on power domain.
>
> This patch does the two things to fix the panic.
> - Don't return an error in gic_acpi_match_gicc() for disabled GICC.
> - No need to keep GICR region information for disabled GICC.
>
> Kernel crash traces:
> Kernel panic - not syncing: No interrupt controller found.
> CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.5 #26
> [<ffff000008087770>] dump_backtrace+0x0/0x218
> [<ffff0000080879dc>] show_stack+0x14/0x20
> [<ffff00000883b078>] dump_stack+0x98/0xb8
> [<ffff0000080c5c14>] panic+0x118/0x26c
> [<ffff000008b62348>] init_IRQ+0x24/0x2c
> [<ffff000008b609fc>] start_kernel+0x230/0x394
> [<ffff000008b601e4>] __primary_switched+0x64/0x6c
> ---[ end Kernel panic - not syncing: No interrupt controller found.
>
> Disabled GICC subtable example:
> Subtable Type : 0B [Generic Interrupt Controller]
> Length : 50
> Reserved : 0000
> CPU Interface Number : 0000003D
> Processor UID : 0000003D
> Flags (decoded below) : 00000000
> Processor Enabled : 0
> Performance Interrupt Trig Mode : 0
> Virtual GIC Interrupt Trig Mode : 0
> Parking Protocol Version : 00000000
> Performance Interrupt : 00000017
> Parked Address : 0000000000000000
> Base Address : 0000000000000000
> Virtual GIC Base Address : 0000000000000000
> Hypervisor GIC Base Address : 0000000000000000
> Virtual GIC Interrupt : 00000019
> Redistributor Base Address : 0000FFFF88F40000
> ARM MPIDR : 000000000000000D
> Efficiency Class : 00
> Reserved : 000000
>
> Signed-off-by: Shanker Donthineni <[email protected]>
> ---
> drivers/irqchip/irq-gic-v3.c | 14 +++++++++-----
> 1 file changed, 9 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c
> index b56c3e2..a30fbac 100644
> --- a/drivers/irqchip/irq-gic-v3.c
> +++ b/drivers/irqchip/irq-gic-v3.c
> @@ -1331,6 +1331,10 @@ static int __init gic_of_init(struct device_node *node, struct device_node *pare
> u32 size = reg == GIC_PIDR2_ARCH_GICv4 ? SZ_64K * 4 : SZ_64K * 2;
> void __iomem *redist_base;
>
> + /* GICC entry which has !ACPI_MADT_ENABLED is not unusable so skip */
> + if (!(gicc->flags & ACPI_MADT_ENABLED))
> + return 0;
> +
> redist_base = ioremap(gicc->gicr_base_address, size);
> if (!redist_base)
> return -ENOMEM;
> @@ -1374,13 +1378,13 @@ static int __init gic_acpi_match_gicc(struct acpi_subtable_header *header,
> (struct acpi_madt_generic_interrupt *)header;
>
> /*
> - * If GICC is enabled and has valid gicr base address, then it means
> - * GICR base is presented via GICC
> + * If GICC is enabled and has not valid gicr base address, then it means
> + * GICR base is not presented via GICC
> */
> - if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
> - return 0;
> + if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
> + return -ENODEV;
This doesn't feel quite right. It would mean that having the ENABLED
flag cleared and potentially no address would make it valid? It looks to
me that the original code is "less wrong".
What am I missing?
Thanks,
M.
--
Jazz is not dead. It just smells funny...
Hi Thanks,
On 12/04/2017 04:28 AM, Marc Zyngier wrote:
> On 03/12/17 23:21, Shanker Donthineni wrote:
>> As per MADT specification, it's perfectly valid firmware can pass
>> MADT table to OS with disabled GICC entries. ARM64-SMP code skips
>> those cpu cores to bring online. However the current GICv3 driver
>> probe bails out in this case on systems where redistributor regions
>> are not in the always-on power domain.
>>
>> This patch does the two things to fix the panic.
>> - Don't return an error in gic_acpi_match_gicc() for disabled GICC.
>> - No need to keep GICR region information for disabled GICC.
>>
>> Kernel crash traces:
>> Kernel panic - not syncing: No interrupt controller found.
>> CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.5 #26
>> [<ffff000008087770>] dump_backtrace+0x0/0x218
>> [<ffff0000080879dc>] show_stack+0x14/0x20
>> [<ffff00000883b078>] dump_stack+0x98/0xb8
>> [<ffff0000080c5c14>] panic+0x118/0x26c
>> [<ffff000008b62348>] init_IRQ+0x24/0x2c
>> [<ffff000008b609fc>] start_kernel+0x230/0x394
>> [<ffff000008b601e4>] __primary_switched+0x64/0x6c
>> ---[ end Kernel panic - not syncing: No interrupt controller found.
>>
>> Disabled GICC subtable example:
>> Subtable Type : 0B [Generic Interrupt Controller]
>> Length : 50
>> Reserved : 0000
>> CPU Interface Number : 0000003D
>> Processor UID : 0000003D
>> Flags (decoded below) : 00000000
>> Processor Enabled : 0
>> Performance Interrupt Trig Mode : 0
>> Virtual GIC Interrupt Trig Mode : 0
>> Parking Protocol Version : 00000000
>> Performance Interrupt : 00000017
>> Parked Address : 0000000000000000
>> Base Address : 0000000000000000
>> Virtual GIC Base Address : 0000000000000000
>> Hypervisor GIC Base Address : 0000000000000000
>> Virtual GIC Interrupt : 00000019
>> Redistributor Base Address : 0000FFFF88F40000
>> ARM MPIDR : 000000000000000D
>> Efficiency Class : 00
>> Reserved : 000000
>>
>> Signed-off-by: Shanker Donthineni <[email protected]>
>> ---
>> drivers/irqchip/irq-gic-v3.c | 14 +++++++++-----
>> 1 file changed, 9 insertions(+), 5 deletions(-)
>>
>> diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c
>> index b56c3e2..a30fbac 100644
>> --- a/drivers/irqchip/irq-gic-v3.c
>> +++ b/drivers/irqchip/irq-gic-v3.c
>> @@ -1331,6 +1331,10 @@ static int __init gic_of_init(struct device_node *node, struct device_node *pare
>> u32 size = reg == GIC_PIDR2_ARCH_GICv4 ? SZ_64K * 4 : SZ_64K * 2;
>> void __iomem *redist_base;
>>
>> + /* GICC entry which has !ACPI_MADT_ENABLED is not unusable so skip */
>> + if (!(gicc->flags & ACPI_MADT_ENABLED))
>> + return 0;
>> +
>> redist_base = ioremap(gicc->gicr_base_address, size);
>> if (!redist_base)
>> return -ENOMEM;
>> @@ -1374,13 +1378,13 @@ static int __init gic_acpi_match_gicc(struct acpi_subtable_header *header,
>> (struct acpi_madt_generic_interrupt *)header;
>>
>> /*
>> - * If GICC is enabled and has valid gicr base address, then it means
>> - * GICR base is presented via GICC
>> + * If GICC is enabled and has not valid gicr base address, then it means
>> + * GICR base is not presented via GICC
>> */
>> - if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
>> - return 0;
>> + if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
>> + return -ENODEV;
>
> This doesn't feel quite right. It would mean that having the ENABLED
> flag cleared and potentially no address would make it valid? It looks to
> me that the original code is "less wrong".
>
> What am I missing?
>
Original definition of the function gic_acpi_match_gicc().
{
if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
return 0;
return -ENODEV;
}
Above code triggers the driver probe fail for the two reasons.
1) GICC with ACPI_MADT_ENABLED=0, it's a bug according to ACPI spec.
2) GICC with ACPI_MADT_ENABLED=1 and invalid GICR address, expected.
This patch fix the first failed case and keep the second case intact.
if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
return -ENODEV;
return 0;
> Thanks,
>
> M.
>
--
Shanker Donthineni
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
On 04/12/17 14:04, Shanker Donthineni wrote:
> Hi Thanks,
>
> On 12/04/2017 04:28 AM, Marc Zyngier wrote:
>> On 03/12/17 23:21, Shanker Donthineni wrote:
>>> As per MADT specification, it's perfectly valid firmware can pass
>>> MADT table to OS with disabled GICC entries. ARM64-SMP code skips
>>> those cpu cores to bring online. However the current GICv3 driver
>>> probe bails out in this case on systems where redistributor regions
>>> are not in the always-on power domain.
>>>
>>> This patch does the two things to fix the panic.
>>> - Don't return an error in gic_acpi_match_gicc() for disabled GICC.
>>> - No need to keep GICR region information for disabled GICC.
>>>
>>> Kernel crash traces:
>>> Kernel panic - not syncing: No interrupt controller found.
>>> CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.5 #26
>>> [<ffff000008087770>] dump_backtrace+0x0/0x218
>>> [<ffff0000080879dc>] show_stack+0x14/0x20
>>> [<ffff00000883b078>] dump_stack+0x98/0xb8
>>> [<ffff0000080c5c14>] panic+0x118/0x26c
>>> [<ffff000008b62348>] init_IRQ+0x24/0x2c
>>> [<ffff000008b609fc>] start_kernel+0x230/0x394
>>> [<ffff000008b601e4>] __primary_switched+0x64/0x6c
>>> ---[ end Kernel panic - not syncing: No interrupt controller found.
>>>
>>> Disabled GICC subtable example:
>>> Subtable Type : 0B [Generic Interrupt Controller]
>>> Length : 50
>>> Reserved : 0000
>>> CPU Interface Number : 0000003D
>>> Processor UID : 0000003D
>>> Flags (decoded below) : 00000000
>>> Processor Enabled : 0
>>> Performance Interrupt Trig Mode : 0
>>> Virtual GIC Interrupt Trig Mode : 0
>>> Parking Protocol Version : 00000000
>>> Performance Interrupt : 00000017
>>> Parked Address : 0000000000000000
>>> Base Address : 0000000000000000
>>> Virtual GIC Base Address : 0000000000000000
>>> Hypervisor GIC Base Address : 0000000000000000
>>> Virtual GIC Interrupt : 00000019
>>> Redistributor Base Address : 0000FFFF88F40000
>>> ARM MPIDR : 000000000000000D
>>> Efficiency Class : 00
>>> Reserved : 000000
>>>
>>> Signed-off-by: Shanker Donthineni <[email protected]>
>>> ---
>>> drivers/irqchip/irq-gic-v3.c | 14 +++++++++-----
>>> 1 file changed, 9 insertions(+), 5 deletions(-)
>>>
>>> diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c
>>> index b56c3e2..a30fbac 100644
>>> --- a/drivers/irqchip/irq-gic-v3.c
>>> +++ b/drivers/irqchip/irq-gic-v3.c
>>> @@ -1331,6 +1331,10 @@ static int __init gic_of_init(struct device_node *node, struct device_node *pare
>>> u32 size = reg == GIC_PIDR2_ARCH_GICv4 ? SZ_64K * 4 : SZ_64K * 2;
>>> void __iomem *redist_base;
>>>
>>> + /* GICC entry which has !ACPI_MADT_ENABLED is not unusable so skip */
>>> + if (!(gicc->flags & ACPI_MADT_ENABLED))
>>> + return 0;
>>> +
>>> redist_base = ioremap(gicc->gicr_base_address, size);
>>> if (!redist_base)
>>> return -ENOMEM;
>>> @@ -1374,13 +1378,13 @@ static int __init gic_acpi_match_gicc(struct acpi_subtable_header *header,
>>> (struct acpi_madt_generic_interrupt *)header;
>>>
>>> /*
>>> - * If GICC is enabled and has valid gicr base address, then it means
>>> - * GICR base is presented via GICC
>>> + * If GICC is enabled and has not valid gicr base address, then it means
>>> + * GICR base is not presented via GICC
>>> */
>>> - if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
>>> - return 0;
>>> + if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
>>> + return -ENODEV;
>>
>> This doesn't feel quite right. It would mean that having the ENABLED
>> flag cleared and potentially no address would make it valid? It looks to
>> me that the original code is "less wrong".
>>
>> What am I missing?
>>
>
> Original definition of the function gic_acpi_match_gicc().
> {
> if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
> return 0;
>
> return -ENODEV;
> }
>
> Above code triggers the driver probe fail for the two reasons.
> 1) GICC with ACPI_MADT_ENABLED=0, it's a bug according to ACPI spec.
> 2) GICC with ACPI_MADT_ENABLED=1 and invalid GICR address, expected.
>
>
> This patch fix the first failed case and keep the second case intact.
> if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
> return -ENODEV;
>
> return 0;
If (1) is a firmware bug, then why is it handled in the SMP code? You're
even saying that this is the right thing to do?
As for (2), you seem to imply that only the address matter. So why isn't
it just:
if (gicc->gicr_base_address)
return 0;
?
Thanks,
M.
--
Jazz is not dead. It just smells funny...
Hi Marc,
On 12/05/2017 02:59 AM, Marc Zyngier wrote:
> On 04/12/17 14:04, Shanker Donthineni wrote:
>> Hi Thanks,
>>
>> On 12/04/2017 04:28 AM, Marc Zyngier wrote:
>>> On 03/12/17 23:21, Shanker Donthineni wrote:
>>>> As per MADT specification, it's perfectly valid firmware can pass
>>>> MADT table to OS with disabled GICC entries. ARM64-SMP code skips
>>>> those cpu cores to bring online. However the current GICv3 driver
>>>> probe bails out in this case on systems where redistributor regions
>>>> are not in the always-on power domain.
>>>>
>>>> This patch does the two things to fix the panic.
>>>> - Don't return an error in gic_acpi_match_gicc() for disabled GICC.
>>>> - No need to keep GICR region information for disabled GICC.
>>>>
>>>> Kernel crash traces:
>>>> Kernel panic - not syncing: No interrupt controller found.
>>>> CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.5 #26
>>>> [<ffff000008087770>] dump_backtrace+0x0/0x218
>>>> [<ffff0000080879dc>] show_stack+0x14/0x20
>>>> [<ffff00000883b078>] dump_stack+0x98/0xb8
>>>> [<ffff0000080c5c14>] panic+0x118/0x26c
>>>> [<ffff000008b62348>] init_IRQ+0x24/0x2c
>>>> [<ffff000008b609fc>] start_kernel+0x230/0x394
>>>> [<ffff000008b601e4>] __primary_switched+0x64/0x6c
>>>> ---[ end Kernel panic - not syncing: No interrupt controller found.
>>>>
>>>> Disabled GICC subtable example:
>>>> Subtable Type : 0B [Generic Interrupt Controller]
>>>> Length : 50
>>>> Reserved : 0000
>>>> CPU Interface Number : 0000003D
>>>> Processor UID : 0000003D
>>>> Flags (decoded below) : 00000000
>>>> Processor Enabled : 0
>>>> Performance Interrupt Trig Mode : 0
>>>> Virtual GIC Interrupt Trig Mode : 0
>>>> Parking Protocol Version : 00000000
>>>> Performance Interrupt : 00000017
>>>> Parked Address : 0000000000000000
>>>> Base Address : 0000000000000000
>>>> Virtual GIC Base Address : 0000000000000000
>>>> Hypervisor GIC Base Address : 0000000000000000
>>>> Virtual GIC Interrupt : 00000019
>>>> Redistributor Base Address : 0000FFFF88F40000
>>>> ARM MPIDR : 000000000000000D
>>>> Efficiency Class : 00
>>>> Reserved : 000000
>>>>
>>>> Signed-off-by: Shanker Donthineni <[email protected]>
>>>> ---
>>>> drivers/irqchip/irq-gic-v3.c | 14 +++++++++-----
>>>> 1 file changed, 9 insertions(+), 5 deletions(-)
>>>>
>>>> diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c
>>>> index b56c3e2..a30fbac 100644
>>>> --- a/drivers/irqchip/irq-gic-v3.c
>>>> +++ b/drivers/irqchip/irq-gic-v3.c
>>>> @@ -1331,6 +1331,10 @@ static int __init gic_of_init(struct device_node *node, struct device_node *pare
>>>> u32 size = reg == GIC_PIDR2_ARCH_GICv4 ? SZ_64K * 4 : SZ_64K * 2;
>>>> void __iomem *redist_base;
>>>>
>>>> + /* GICC entry which has !ACPI_MADT_ENABLED is not unusable so skip */
>>>> + if (!(gicc->flags & ACPI_MADT_ENABLED))
>>>> + return 0;
>>>> +
>>>> redist_base = ioremap(gicc->gicr_base_address, size);
>>>> if (!redist_base)
>>>> return -ENOMEM;
>>>> @@ -1374,13 +1378,13 @@ static int __init gic_acpi_match_gicc(struct acpi_subtable_header *header,
>>>> (struct acpi_madt_generic_interrupt *)header;
>>>>
>>>> /*
>>>> - * If GICC is enabled and has valid gicr base address, then it means
>>>> - * GICR base is presented via GICC
>>>> + * If GICC is enabled and has not valid gicr base address, then it means
>>>> + * GICR base is not presented via GICC
>>>> */
>>>> - if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
>>>> - return 0;
>>>> + if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
>>>> + return -ENODEV;
>>>
>>> This doesn't feel quite right. It would mean that having the ENABLED
>>> flag cleared and potentially no address would make it valid? It looks to
>>> me that the original code is "less wrong".
>>>
>>> What am I missing?
>>>
>>
>> Original definition of the function gic_acpi_match_gicc().
>> {
>> if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
>> return 0;
>>
>> return -ENODEV;
>> }
>>
>> Above code triggers the driver probe fail for the two reasons.
>> 1) GICC with ACPI_MADT_ENABLED=0, it's a bug according to ACPI spec.
>> 2) GICC with ACPI_MADT_ENABLED=1 and invalid GICR address, expected.
>>
>>
>> This patch fix the first failed case and keep the second case intact.
>> if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
>> return -ENODEV;
>>
>> return 0;
> If (1) is a firmware bug, then why is it handled in the SMP code? You're
> even saying that this is the right thing to do?
>
It's a bug in Linux GICv3 driver not firmware. Firmware is populating MADT
table according to ACPI specification.
> As for (2), you seem to imply that only the address matter. So why isn't
> it just:
>
> if (gicc->gicr_base_address)
> return 0;
>
> ?
ACPI spec says operating shouldn't attempt to use GICC configuration parameters
if the flag ACPI_MADT_ENABLED is cleared. I believe we should check GICR address
only for enabled GICC interfaces.
>
> Thanks,
>
> M.
>
--
Shanker Donthineni
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
On 05/12/17 13:21, Shanker Donthineni wrote:
> Hi Marc,
>
> On 12/05/2017 02:59 AM, Marc Zyngier wrote:
>> On 04/12/17 14:04, Shanker Donthineni wrote:
>>> Hi Thanks,
>>>
>>> On 12/04/2017 04:28 AM, Marc Zyngier wrote:
>>>> On 03/12/17 23:21, Shanker Donthineni wrote:
>>>>> As per MADT specification, it's perfectly valid firmware can pass
>>>>> MADT table to OS with disabled GICC entries. ARM64-SMP code skips
>>>>> those cpu cores to bring online. However the current GICv3 driver
>>>>> probe bails out in this case on systems where redistributor regions
>>>>> are not in the always-on power domain.
>>>>>
>>>>> This patch does the two things to fix the panic.
>>>>> - Don't return an error in gic_acpi_match_gicc() for disabled GICC.
>>>>> - No need to keep GICR region information for disabled GICC.
>>>>>
>>>>> Kernel crash traces:
>>>>> Kernel panic - not syncing: No interrupt controller found.
>>>>> CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.13.5 #26
>>>>> [<ffff000008087770>] dump_backtrace+0x0/0x218
>>>>> [<ffff0000080879dc>] show_stack+0x14/0x20
>>>>> [<ffff00000883b078>] dump_stack+0x98/0xb8
>>>>> [<ffff0000080c5c14>] panic+0x118/0x26c
>>>>> [<ffff000008b62348>] init_IRQ+0x24/0x2c
>>>>> [<ffff000008b609fc>] start_kernel+0x230/0x394
>>>>> [<ffff000008b601e4>] __primary_switched+0x64/0x6c
>>>>> ---[ end Kernel panic - not syncing: No interrupt controller found.
>>>>>
>>>>> Disabled GICC subtable example:
>>>>> Subtable Type : 0B [Generic Interrupt Controller]
>>>>> Length : 50
>>>>> Reserved : 0000
>>>>> CPU Interface Number : 0000003D
>>>>> Processor UID : 0000003D
>>>>> Flags (decoded below) : 00000000
>>>>> Processor Enabled : 0
>>>>> Performance Interrupt Trig Mode : 0
>>>>> Virtual GIC Interrupt Trig Mode : 0
>>>>> Parking Protocol Version : 00000000
>>>>> Performance Interrupt : 00000017
>>>>> Parked Address : 0000000000000000
>>>>> Base Address : 0000000000000000
>>>>> Virtual GIC Base Address : 0000000000000000
>>>>> Hypervisor GIC Base Address : 0000000000000000
>>>>> Virtual GIC Interrupt : 00000019
>>>>> Redistributor Base Address : 0000FFFF88F40000
>>>>> ARM MPIDR : 000000000000000D
>>>>> Efficiency Class : 00
>>>>> Reserved : 000000
>>>>>
>>>>> Signed-off-by: Shanker Donthineni <[email protected]>
>>>>> ---
>>>>> drivers/irqchip/irq-gic-v3.c | 14 +++++++++-----
>>>>> 1 file changed, 9 insertions(+), 5 deletions(-)
>>>>>
>>>>> diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c
>>>>> index b56c3e2..a30fbac 100644
>>>>> --- a/drivers/irqchip/irq-gic-v3.c
>>>>> +++ b/drivers/irqchip/irq-gic-v3.c
>>>>> @@ -1331,6 +1331,10 @@ static int __init gic_of_init(struct device_node *node, struct device_node *pare
>>>>> u32 size = reg == GIC_PIDR2_ARCH_GICv4 ? SZ_64K * 4 : SZ_64K * 2;
>>>>> void __iomem *redist_base;
>>>>>
>>>>> + /* GICC entry which has !ACPI_MADT_ENABLED is not unusable so skip */
>>>>> + if (!(gicc->flags & ACPI_MADT_ENABLED))
>>>>> + return 0;
>>>>> +
>>>>> redist_base = ioremap(gicc->gicr_base_address, size);
>>>>> if (!redist_base)
>>>>> return -ENOMEM;
>>>>> @@ -1374,13 +1378,13 @@ static int __init gic_acpi_match_gicc(struct acpi_subtable_header *header,
>>>>> (struct acpi_madt_generic_interrupt *)header;
>>>>>
>>>>> /*
>>>>> - * If GICC is enabled and has valid gicr base address, then it means
>>>>> - * GICR base is presented via GICC
>>>>> + * If GICC is enabled and has not valid gicr base address, then it means
>>>>> + * GICR base is not presented via GICC
>>>>> */
>>>>> - if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
>>>>> - return 0;
>>>>> + if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
>>>>> + return -ENODEV;
>>>>
>>>> This doesn't feel quite right. It would mean that having the ENABLED
>>>> flag cleared and potentially no address would make it valid? It looks to
>>>> me that the original code is "less wrong".
>>>>
>>>> What am I missing?
>>>>
>>>
>>> Original definition of the function gic_acpi_match_gicc().
>>> {
>>> if ((gicc->flags & ACPI_MADT_ENABLED) && gicc->gicr_base_address)
>>> return 0;
>>>
>>> return -ENODEV;
>>> }
>>>
>>> Above code triggers the driver probe fail for the two reasons.
>>> 1) GICC with ACPI_MADT_ENABLED=0, it's a bug according to ACPI spec.
>>> 2) GICC with ACPI_MADT_ENABLED=1 and invalid GICR address, expected.
>>>
>>>
>>> This patch fix the first failed case and keep the second case intact.
>>> if ((gicc->flags & ACPI_MADT_ENABLED) && (!gicc->gicr_base_address))
>>> return -ENODEV;
>>>
>>> return 0;
>> If (1) is a firmware bug, then why is it handled in the SMP code? You're
>> even saying that this is the right thing to do?
>>
>
> It's a bug in Linux GICv3 driver not firmware. Firmware is populating MADT
> table according to ACPI specification.
>
>> As for (2), you seem to imply that only the address matter. So why isn't
>> it just:
>>
>> if (gicc->gicr_base_address)
>> return 0;
>>
>> ?
>
> ACPI spec says operating shouldn't attempt to use GICC configuration parameters
> if the flag ACPI_MADT_ENABLED is cleared. I believe we should check GICR address
> only for enabled GICC interfaces.
Then please rewrite the commit message to actually explain this. This is
confusing as hell.
Thanks,
M.
--
Jazz is not dead. It just smells funny...