This series cleans up the driver a bit and implements changes needed to
support EKTF3624-based touchscreen used in Asus TF300T, Google Nexus 7
and similar Tegra3-based tablets.
---
v2: extended with Dmitry's patches (replaced v1 patches 3 and 4)
v3: rebased for v5.7-rc1
v4: rebased onto v5.7-rc2+ (current Linus' master)
update "remove unused axes" and "refactor
elants_i2c_execute_command()" patches after review
add David's patch converting DT binding to YAML
v5: rebased onto dtor/input/for-linus
v6: rebased onto newer dtor/input/for-linus
remove yet unused constants from patch 1
added a new drive-by cleanup (last patch)
v7: rebased onto current dtor/input/for-next
v8: rebased onto current dtor/input/for-linus again
---
Dmitry Osipenko (1):
input: elants: support 0x66 reply opcode for reporting touches
Michał Mirosław (3):
input: elants: document some registers and values
input: elants: support old touch report format
input: elants: read touchscreen size for EKTF3624
drivers/input/touchscreen/elants_i2c.c | 149 +++++++++++++++++++++----
1 file changed, 127 insertions(+), 22 deletions(-)
--
2.20.1
EKTF3624 as present in Asus TF300T tablet has touchscreen size encoded
in different registers.
Signed-off-by: Michał Mirosław <[email protected]>
Reviewed-by: Dmitry Osipenko <[email protected]>
Tested-by: Dmitry Osipenko <[email protected]>
---
drivers/input/touchscreen/elants_i2c.c | 84 ++++++++++++++++++++++++--
1 file changed, 79 insertions(+), 5 deletions(-)
diff --git a/drivers/input/touchscreen/elants_i2c.c b/drivers/input/touchscreen/elants_i2c.c
index f1bf3e000e96..c24d8cdc4251 100644
--- a/drivers/input/touchscreen/elants_i2c.c
+++ b/drivers/input/touchscreen/elants_i2c.c
@@ -35,7 +35,7 @@
#include <linux/input/mt.h>
#include <linux/input/touchscreen.h>
#include <linux/acpi.h>
-#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/gpio/consumer.h>
#include <linux/regulator/consumer.h>
#include <asm/unaligned.h>
@@ -43,6 +43,10 @@
/* Device, Driver information */
#define DEVICE_NAME "elants_i2c"
+/* Device IDs */
+#define EKTH3500 0
+#define EKTF3624 1
+
/* Convert from rows or columns into resolution */
#define ELAN_TS_RESOLUTION(n, m) (((n) - 1) * (m))
@@ -94,6 +98,8 @@
#define E_ELAN_INFO_REK 0xD0
#define E_ELAN_INFO_TEST_VER 0xE0
#define E_ELAN_INFO_FW_ID 0xF0
+#define E_INFO_X_RES 0x60
+#define E_INFO_Y_RES 0x63
#define E_INFO_OSR 0xD6
#define E_INFO_PHY_SCAN 0xD7
#define E_INFO_PHY_DRIVER 0xD8
@@ -157,6 +163,7 @@ struct elants_data {
bool wake_irq_enabled;
bool keep_power_in_suspend;
+ u8 chip_id;
/* Must be last to be used for DMA operations */
u8 buf[MAX_PACKET_SIZE] ____cacheline_aligned;
@@ -434,7 +441,58 @@ static int elants_i2c_query_bc_version(struct elants_data *ts)
return 0;
}
-static int elants_i2c_query_ts_info(struct elants_data *ts)
+static int elants_i2c_query_ts_info_ektf(struct elants_data *ts)
+{
+ struct i2c_client *client = ts->client;
+ int error;
+ u8 resp[4];
+ u16 phy_x, phy_y;
+ const u8 get_xres_cmd[] = {
+ CMD_HEADER_READ, E_INFO_X_RES, 0x00, 0x00
+ };
+ const u8 get_yres_cmd[] = {
+ CMD_HEADER_READ, E_INFO_Y_RES, 0x00, 0x00
+ };
+
+ /* Get X/Y size in mm */
+ error = elants_i2c_execute_command(client, get_xres_cmd,
+ sizeof(get_xres_cmd),
+ resp, sizeof(resp), 1,
+ "get X size");
+ if (error)
+ return error;
+
+ phy_x = resp[2] | ((resp[3] & 0xF0) << 4);
+
+ error = elants_i2c_execute_command(client, get_yres_cmd,
+ sizeof(get_yres_cmd),
+ resp, sizeof(resp), 1,
+ "get Y size");
+ if (error)
+ return error;
+
+ phy_y = resp[2] | ((resp[3] & 0xF0) << 4);
+
+ if (!phy_x || !phy_y) {
+ dev_warn(&client->dev,
+ "invalid size data: %d x %d mm\n",
+ phy_x, phy_y);
+ return 0;
+ }
+
+ dev_dbg(&client->dev, "phy_x=%d, phy_y=%d\n", phy_x, phy_y);
+
+ /* calculate resolution from size */
+ ts->x_max = 2240-1;
+ ts->x_res = DIV_ROUND_CLOSEST(ts->prop.max_x, phy_x);
+
+ ts->y_max = 1408-1;
+ ts->y_res = DIV_ROUND_CLOSEST(ts->prop.max_y, phy_y);
+
+ return 0;
+}
+
+static int elants_i2c_query_ts_info_ekth(struct elants_data *ts)
{
struct i2c_client *client = ts->client;
int error;
@@ -588,8 +646,20 @@ static int elants_i2c_initialize(struct elants_data *ts)
error = elants_i2c_query_fw_version(ts);
if (!error)
error = elants_i2c_query_test_version(ts);
- if (!error)
- error = elants_i2c_query_ts_info(ts);
+
+ switch (ts->chip_id) {
+ case EKTH3500:
+ if (!error)
+ error = elants_i2c_query_ts_info_ekth(ts);
+ break;
+ case EKTF3624:
+ if (!error)
+ error = elants_i2c_query_ts_info_ektf(ts);
+ break;
+ default:
+ unreachable();
+ break;
+ }
if (error)
ts->iap_mode = ELAN_IAP_RECOVERY;
@@ -1266,6 +1336,9 @@ static int elants_i2c_probe(struct i2c_client *client,
ts->client = client;
i2c_set_clientdata(client, ts);
+ if (client->dev.of_node)
+ ts->chip_id = (uintptr_t)of_device_get_match_data(&client->dev);
+
ts->vcc33 = devm_regulator_get(&client->dev, "vcc33");
if (IS_ERR(ts->vcc33)) {
error = PTR_ERR(ts->vcc33);
@@ -1495,7 +1568,8 @@ MODULE_DEVICE_TABLE(acpi, elants_acpi_id);
#ifdef CONFIG_OF
static const struct of_device_id elants_of_match[] = {
- { .compatible = "elan,ekth3500" },
+ { .compatible = "elan,ekth3500", .data = (void *)EKTH3500 },
+ { .compatible = "elan,ektf3624", .data = (void *)EKTF3624 },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, elants_of_match);
--
2.20.1
Add information found in downstream kernels, to make the code less
magic.
Signed-off-by: Michał Mirosław <[email protected]>
Reviewed-by: Dmitry Osipenko <[email protected]>
Tested-by: Dmitry Osipenko <[email protected]>
---
drivers/input/touchscreen/elants_i2c.c | 18 +++++++++++++-----
1 file changed, 13 insertions(+), 5 deletions(-)
diff --git a/drivers/input/touchscreen/elants_i2c.c b/drivers/input/touchscreen/elants_i2c.c
index 50c348297e38..d51cb910fba1 100644
--- a/drivers/input/touchscreen/elants_i2c.c
+++ b/drivers/input/touchscreen/elants_i2c.c
@@ -82,7 +82,7 @@
#define HEADER_REPORT_10_FINGER 0x62
-/* Header (4 bytes) plus 3 fill 10-finger packets */
+/* Header (4 bytes) plus 3 full 10-finger packets */
#define MAX_PACKET_SIZE 169
#define BOOT_TIME_DELAY_MS 50
@@ -97,6 +97,10 @@
#define E_INFO_PHY_SCAN 0xD7
#define E_INFO_PHY_DRIVER 0xD8
+/* FW write command, 0x54 0x?? 0x0, 0x01 */
+#define E_POWER_STATE_SLEEP 0x50
+#define E_POWER_STATE_RESUME 0x58
+
#define MAX_RETRIES 3
#define MAX_FW_UPDATE_RETRIES 30
@@ -269,8 +273,8 @@ static int elants_i2c_calibrate(struct elants_data *ts)
{
struct i2c_client *client = ts->client;
int ret, error;
- static const u8 w_flashkey[] = { 0x54, 0xC0, 0xE1, 0x5A };
- static const u8 rek[] = { 0x54, 0x29, 0x00, 0x01 };
+ static const u8 w_flashkey[] = { CMD_HEADER_WRITE, 0xC0, 0xE1, 0x5A };
+ static const u8 rek[] = { CMD_HEADER_WRITE, 0x29, 0x00, 0x01 };
static const u8 rek_resp[] = { CMD_HEADER_REK, 0x66, 0x66, 0x66 };
disable_irq(client->irq);
@@ -1388,7 +1392,9 @@ static int __maybe_unused elants_i2c_suspend(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct elants_data *ts = i2c_get_clientdata(client);
- const u8 set_sleep_cmd[] = { 0x54, 0x50, 0x00, 0x01 };
+ const u8 set_sleep_cmd[] = {
+ CMD_HEADER_WRITE, E_POWER_STATE_SLEEP, 0x00, 0x01
+ };
int retry_cnt;
int error;
@@ -1425,7 +1431,9 @@ static int __maybe_unused elants_i2c_resume(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct elants_data *ts = i2c_get_clientdata(client);
- const u8 set_active_cmd[] = { 0x54, 0x58, 0x00, 0x01 };
+ const u8 set_active_cmd[] = {
+ CMD_HEADER_WRITE, E_POWER_STATE_RESUME, 0x00, 0x01
+ };
int retry_cnt;
int error;
--
2.20.1
From: Dmitry Osipenko <[email protected]>
eKTF3624 touchscreen firmware uses two variants of the reply opcodes for
reporting touch events: one is 0x63 (used by older firmware) and other is
0x66 (used by newer firmware). The 0x66 variant is equal to 0x63 of
eKTH3500, while 0x63 needs small adjustment of the touch pressure value.
Nexus 7 tablet device has eKTF3624 touchscreen and it uses 0x66 opcode for
reporting touch events, let's support it now. Other devices, eg. ASUS TF300T,
use 0x63.
Note: CMD_HEADER_REK is used for replying to calibration requests, it has
the same 0x66 opcode number which eKTF3624 uses for reporting touches.
The calibration replies are handled separately from the the rest of the
commands in the driver by entering into ELAN_WAIT_RECALIBRATION state
and thus this change shouldn't change the old behavior.
Signed-off-by: Dmitry Osipenko <[email protected]>
Tested-by: Michał Mirosław <[email protected]>
Signed-off-by: Michał Mirosław <[email protected]>
---
drivers/input/touchscreen/elants_i2c.c | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)
diff --git a/drivers/input/touchscreen/elants_i2c.c b/drivers/input/touchscreen/elants_i2c.c
index c24d8cdc4251..1cbda6f20d07 100644
--- a/drivers/input/touchscreen/elants_i2c.c
+++ b/drivers/input/touchscreen/elants_i2c.c
@@ -61,6 +61,15 @@
#define QUEUE_HEADER_NORMAL 0X63
#define QUEUE_HEADER_WAIT 0x64
+/*
+ * Depending on firmware version, eKTF3624 touchscreens may utilize one of
+ * these opcodes for the touch events: 0x63 and 0x66. The 0x63 is used by
+ * older firmware version and differs from 0x66 such that touch pressure
+ * value needs to be adjusted. The 0x66 opcode of newer firmware is equal
+ * to 0x63 of eKTH3500.
+ */
+#define QUEUE_HEADER_NORMAL2 0x66
+
/* Command header definition */
#define CMD_HEADER_WRITE 0x54
#define CMD_HEADER_READ 0x53
@@ -1052,7 +1061,6 @@ static irqreturn_t elants_i2c_irq(int irq, void *_dev)
switch (ts->buf[FW_HDR_TYPE]) {
case CMD_HEADER_HELLO:
case CMD_HEADER_RESP:
- case CMD_HEADER_REK:
break;
case QUEUE_HEADER_WAIT:
@@ -1072,6 +1080,7 @@ static irqreturn_t elants_i2c_irq(int irq, void *_dev)
break;
case QUEUE_HEADER_NORMAL:
+ case QUEUE_HEADER_NORMAL2:
report_count = ts->buf[FW_HDR_COUNT];
if (report_count == 0 || report_count > 3) {
dev_err(&client->dev,
--
2.20.1