Hi all,
I don't know how much a defconfig is supposed to provide, hence as RFC.
This patches are needed for booting Zynq into a minimum ramfs based
system with a serial console.
Thanks,
Sören
Soren Brinkmann (2):
arm: multi_v7_defconfig: Enable Zynq UART driver
arm: multi_v7_defconfig: Enable initrd/initramfs support
arch/arm/configs/multi_v7_defconfig | 3 +++
1 file changed, 3 insertions(+)
--
1.8.3.1
Signed-off-by: Soren Brinkmann <[email protected]>
---
arch/arm/configs/multi_v7_defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index 2e67a27..d5f0d76 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -42,6 +42,8 @@ CONFIG_KEYBOARD_SPEAR=y
CONFIG_SERIAL_AMBA_PL011=y
CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_XILINX_PS_UART=y
+CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
CONFIG_SERIAL_SIRFSOC=y
CONFIG_SERIAL_SIRFSOC_CONSOLE=y
CONFIG_SERIAL_VT8500=y
--
1.8.3.1
Add CONFIG_BLK_DEV_INITRD to the defconfig to support
initramfs and initrd.
Signed-off-by: Soren Brinkmann <[email protected]>
---
arch/arm/configs/multi_v7_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index d5f0d76..2deda6d 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -83,3 +83,4 @@ CONFIG_DMADEVICES=y
CONFIG_PL330_DMA=y
CONFIG_SIRF_DMA=y
CONFIG_DW_DMAC=y
+CONFIG_BLK_DEV_INITRD=y
--
1.8.3.1
On Wednesday 19 June 2013, Soren Brinkmann wrote:
> I don't know how much a defconfig is supposed to provide, hence as RFC.
> This patches are needed for booting Zynq into a minimum ramfs based
> system with a serial console.
In my opinion we should provide enable all the platform specific drivers
in the defconfigs, as well as everything needed to boot the system,
to get proper compile coverage as well as the ability to test changes
easily. Your patches look good. Michal, would you apply them and
send another pull request or should I just take them directly?
Arnd
On 06/19/2013 08:46 PM, Arnd Bergmann wrote:
> On Wednesday 19 June 2013, Soren Brinkmann wrote:
>> I don't know how much a defconfig is supposed to provide, hence as RFC.
>> This patches are needed for booting Zynq into a minimum ramfs based
>> system with a serial console.
>
> In my opinion we should provide enable all the platform specific drivers
> in the defconfigs, as well as everything needed to boot the system,
> to get proper compile coverage as well as the ability to test changes
> easily. Your patches look good. Michal, would you apply them and
> send another pull request or should I just take them directly?
Soren asked me 2 days ago if make sense to create zynq defconfig or not.
I just suggested him to better extend this multi_v7_defconfig.
But still question is if we can/should create zynq specific defconfig?
Or are you going to remove all of these platform specific defconfig?
Definitely agree that multi_v7 defconfig should enable everything needed
to boot the system.
Does it also mean that we should also enable all zynq drivers
to get better compile coverage?
Thanks,
Michal
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: http://www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform
On Thursday 20 June 2013, Michal Simek wrote:
> On 06/19/2013 08:46 PM, Arnd Bergmann wrote:
> > On Wednesday 19 June 2013, Soren Brinkmann wrote:
> >> I don't know how much a defconfig is supposed to provide, hence as RFC.
> >> This patches are needed for booting Zynq into a minimum ramfs based
> >> system with a serial console.
> >
> > In my opinion we should provide enable all the platform specific drivers
> > in the defconfigs, as well as everything needed to boot the system,
> > to get proper compile coverage as well as the ability to test changes
> > easily. Your patches look good. Michal, would you apply them and
> > send another pull request or should I just take them directly?
>
> Soren asked me 2 days ago if make sense to create zynq defconfig or not.
> I just suggested him to better extend this multi_v7_defconfig.
> But still question is if we can/should create zynq specific defconfig?
> Or are you going to remove all of these platform specific defconfig?
We don't have a consistent policy across platforms at the moment.
Traditionally we had multiple defconfigs per platform, in some cases
one per board, but moving towards one defconfig per platform at
the moment.
I guess whether or not to have a separate defconfig for one platform
or to use only multi_*_defconfig is a question of how many people
would use a zynq_defconfig in practice.
> Definitely agree that multi_v7 defconfig should enable everything needed
> to boot the system.
> Does it also mean that we should also enable all zynq drivers
> to get better compile coverage?
I would say yes.
My feeling is that multi_v7_defconfig should enable all hardware
support for the platforms in it, and that users would take it
as a starting point if they want to have a configuration for
an embedded system, disabling everything they don't need.
Arnd
On 06/20/2013 10:02 AM, Arnd Bergmann wrote:
> On Thursday 20 June 2013, Michal Simek wrote:
>> On 06/19/2013 08:46 PM, Arnd Bergmann wrote:
>>> On Wednesday 19 June 2013, Soren Brinkmann wrote:
>>>> I don't know how much a defconfig is supposed to provide, hence as RFC.
>>>> This patches are needed for booting Zynq into a minimum ramfs based
>>>> system with a serial console.
>>>
>>> In my opinion we should provide enable all the platform specific drivers
>>> in the defconfigs, as well as everything needed to boot the system,
>>> to get proper compile coverage as well as the ability to test changes
>>> easily. Your patches look good. Michal, would you apply them and
>>> send another pull request or should I just take them directly?
>>
>> Soren asked me 2 days ago if make sense to create zynq defconfig or not.
>> I just suggested him to better extend this multi_v7_defconfig.
>> But still question is if we can/should create zynq specific defconfig?
>> Or are you going to remove all of these platform specific defconfig?
>
> We don't have a consistent policy across platforms at the moment.
> Traditionally we had multiple defconfigs per platform, in some cases
> one per board, but moving towards one defconfig per platform at
> the moment.
That's what I though but on the other hand in this process
all these defconfigs should be removed.
> I guess whether or not to have a separate defconfig for one platform
> or to use only multi_*_defconfig is a question of how many people
> would use a zynq_defconfig in practice.
The point is if you look at zynq users than they will just use this zynq_defconfig
because they know that it is for zynq and also they don't want to
compile drivers for other platforms which zynq can't use.
From distribution point of view they want to use only one image because it is just
easier.
Based on this if there is an option to also add just zynq defconfig, I would prefer
to also add it.
>> Definitely agree that multi_v7 defconfig should enable everything needed
>> to boot the system.
>> Does it also mean that we should also enable all zynq drivers
>> to get better compile coverage?
>
> I would say yes.
>
> My feeling is that multi_v7_defconfig should enable all hardware
> support for the platforms in it, and that users would take it
> as a starting point if they want to have a configuration for
> an embedded system, disabling everything they don't need.
I just wanted to be sure because you wrote just drivers for booting
it means any "minimal" configuration to get it boot not all drivers.
If you are ok, Soren will prepare also specific zynq defconfig file
and check if there are any missing drivers which are not enabled for zynq
for multi_v7. I will collect them in one branch and will send pull request.
Thanks,
Michal
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: http://www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform
On Thu, Jun 20, 2013 at 10:27:44AM +0200, Michal Simek wrote:
> On 06/20/2013 10:02 AM, Arnd Bergmann wrote:
> > On Thursday 20 June 2013, Michal Simek wrote:
> >> On 06/19/2013 08:46 PM, Arnd Bergmann wrote:
> >>> On Wednesday 19 June 2013, Soren Brinkmann wrote:
> >>>> I don't know how much a defconfig is supposed to provide, hence as RFC.
> >>>> This patches are needed for booting Zynq into a minimum ramfs based
> >>>> system with a serial console.
> >>>
> >>> In my opinion we should provide enable all the platform specific drivers
> >>> in the defconfigs, as well as everything needed to boot the system,
> >>> to get proper compile coverage as well as the ability to test changes
> >>> easily. Your patches look good. Michal, would you apply them and
> >>> send another pull request or should I just take them directly?
> >>
> >> Soren asked me 2 days ago if make sense to create zynq defconfig or not.
> >> I just suggested him to better extend this multi_v7_defconfig.
> >> But still question is if we can/should create zynq specific defconfig?
> >> Or are you going to remove all of these platform specific defconfig?
> >
> > We don't have a consistent policy across platforms at the moment.
> > Traditionally we had multiple defconfigs per platform, in some cases
> > one per board, but moving towards one defconfig per platform at
> > the moment.
>
> That's what I though but on the other hand in this process
> all these defconfigs should be removed.
>
> > I guess whether or not to have a separate defconfig for one platform
> > or to use only multi_*_defconfig is a question of how many people
> > would use a zynq_defconfig in practice.
>
> The point is if you look at zynq users than they will just use this zynq_defconfig
> because they know that it is for zynq and also they don't want to
> compile drivers for other platforms which zynq can't use.
> From distribution point of view they want to use only one image because it is just
> easier.
>
> Based on this if there is an option to also add just zynq defconfig, I would prefer
> to also add it.
>
> >> Definitely agree that multi_v7 defconfig should enable everything needed
> >> to boot the system.
> >> Does it also mean that we should also enable all zynq drivers
> >> to get better compile coverage?
> >
> > I would say yes.
> >
> > My feeling is that multi_v7_defconfig should enable all hardware
> > support for the platforms in it, and that users would take it
> > as a starting point if they want to have a configuration for
> > an embedded system, disabling everything they don't need.
>
> I just wanted to be sure because you wrote just drivers for booting
> it means any "minimal" configuration to get it boot not all drivers.
>
> If you are ok, Soren will prepare also specific zynq defconfig file
> and check if there are any missing drivers which are not enabled for zynq
> for multi_v7. I will collect them in one branch and will send pull request.
I can check. But I don't think it makes too much sense currently. Even
though multi_v7_defconfig targets several SOCs its pretty minimal. I
think there are just a few SOC BSPs and serial drivers selected. Due to
lacking driver support in mainline, a Zynq specific config would not be
that different, IMHO.
But this does hopefully change with growing driver support for Zynq in
mainline.
Sören
On 06/20/2013 05:41 PM, Sören Brinkmann wrote:
> On Thu, Jun 20, 2013 at 10:27:44AM +0200, Michal Simek wrote:
>> On 06/20/2013 10:02 AM, Arnd Bergmann wrote:
>>> On Thursday 20 June 2013, Michal Simek wrote:
>>>> On 06/19/2013 08:46 PM, Arnd Bergmann wrote:
>>>>> On Wednesday 19 June 2013, Soren Brinkmann wrote:
>>>>>> I don't know how much a defconfig is supposed to provide, hence as RFC.
>>>>>> This patches are needed for booting Zynq into a minimum ramfs based
>>>>>> system with a serial console.
>>>>>
>>>>> In my opinion we should provide enable all the platform specific drivers
>>>>> in the defconfigs, as well as everything needed to boot the system,
>>>>> to get proper compile coverage as well as the ability to test changes
>>>>> easily. Your patches look good. Michal, would you apply them and
>>>>> send another pull request or should I just take them directly?
>>>>
>>>> Soren asked me 2 days ago if make sense to create zynq defconfig or not.
>>>> I just suggested him to better extend this multi_v7_defconfig.
>>>> But still question is if we can/should create zynq specific defconfig?
>>>> Or are you going to remove all of these platform specific defconfig?
>>>
>>> We don't have a consistent policy across platforms at the moment.
>>> Traditionally we had multiple defconfigs per platform, in some cases
>>> one per board, but moving towards one defconfig per platform at
>>> the moment.
>>
>> That's what I though but on the other hand in this process
>> all these defconfigs should be removed.
>>
>>> I guess whether or not to have a separate defconfig for one platform
>>> or to use only multi_*_defconfig is a question of how many people
>>> would use a zynq_defconfig in practice.
>>
>> The point is if you look at zynq users than they will just use this zynq_defconfig
>> because they know that it is for zynq and also they don't want to
>> compile drivers for other platforms which zynq can't use.
>> From distribution point of view they want to use only one image because it is just
>> easier.
>>
>> Based on this if there is an option to also add just zynq defconfig, I would prefer
>> to also add it.
>>
>>>> Definitely agree that multi_v7 defconfig should enable everything needed
>>>> to boot the system.
>>>> Does it also mean that we should also enable all zynq drivers
>>>> to get better compile coverage?
>>>
>>> I would say yes.
>>>
>>> My feeling is that multi_v7_defconfig should enable all hardware
>>> support for the platforms in it, and that users would take it
>>> as a starting point if they want to have a configuration for
>>> an embedded system, disabling everything they don't need.
>>
>> I just wanted to be sure because you wrote just drivers for booting
>> it means any "minimal" configuration to get it boot not all drivers.
>>
>> If you are ok, Soren will prepare also specific zynq defconfig file
>> and check if there are any missing drivers which are not enabled for zynq
>> for multi_v7. I will collect them in one branch and will send pull request.
> I can check. But I don't think it makes too much sense currently. Even
> though multi_v7_defconfig targets several SOCs its pretty minimal. I
> think there are just a few SOC BSPs and serial drivers selected. Due to
> lacking driver support in mainline, a Zynq specific config would not be
> that different, IMHO.
> But this does hopefully change with growing driver support for Zynq in
> mainline.
It depends. Kernel with all possible drivers for all arm multiplatform
could be big and also it will take a lot of time to compile it.
It is more up to Arnd and Olof.
Thanks,
Michal
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: http://www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform