In some use cases Zynq's FPGA clocks are used as static clock
generators for IP in the FPGA part of the SOC for which no Linux driver
exists and would control those clocks. To avoid automatic
gating of these clocks in such cases a new property - fclk-enable - is
added to the clock controller's DT description to accomodate such use
cases. It's value is a bitmask, where a set bit results in enabling
the corresponding FCLK through the clkc.
FPGA clocks are handled following the rules below:
If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
Linux. Drivers can enable and control it through the CCF as usual.
If an FCLK is enabled by bootloaders AND the corresponding bit in the
'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
resulting in an off by one reference count for that clock. Ensuring it
will always be running.
The default value for 'fclk-enable' is '0xf' (all FCLK's enabled by the
bootloader are enabled through the clkc.
Signed-off-by: Soren Brinkmann <[email protected]>
---
.../devicetree/bindings/clock/zynq-7000.txt | 4 ++++
drivers/clk/zynq/clkc.c | 20 +++++++++++++++++---
2 files changed, 21 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/zynq-7000.txt b/Documentation/devicetree/bindings/clock/zynq-7000.txt
index d99af878f5d7..11fdd146ec83 100644
--- a/Documentation/devicetree/bindings/clock/zynq-7000.txt
+++ b/Documentation/devicetree/bindings/clock/zynq-7000.txt
@@ -22,6 +22,10 @@ Required properties:
Optional properties:
- clocks : as described in the clock bindings
- clock-names : as described in the clock bindings
+ - fclk-enable : Bit mask to enable FCLKs in cases no proper CCF compatible
+ driver is available. Bit [0..3] correspond to FCLK0..FCLK3. The
+ corresponding FCLK will only be enabled if it is actually
+ running at boot time. (default = 0xf)
Clock inputs:
The following strings are optional parameters to the 'clock-names' property in
diff --git a/drivers/clk/zynq/clkc.c b/drivers/clk/zynq/clkc.c
index 10772aa72e4e..a36fc0f47634 100644
--- a/drivers/clk/zynq/clkc.c
+++ b/drivers/clk/zynq/clkc.c
@@ -102,9 +102,10 @@ static const char *swdt_ext_clk_input_names[] __initdata = {"swdt_ext_clk"};
static void __init zynq_clk_register_fclk(enum zynq_clk fclk,
const char *clk_name, void __iomem *fclk_ctrl_reg,
- const char **parents)
+ const char **parents, int enable)
{
struct clk *clk;
+ u32 enable_reg;
char *mux_name;
char *div0_name;
char *div1_name;
@@ -147,6 +148,12 @@ static void __init zynq_clk_register_fclk(enum zynq_clk fclk,
clks[fclk] = clk_register_gate(NULL, clk_name,
div1_name, CLK_SET_RATE_PARENT, fclk_gate_reg,
0, CLK_GATE_SET_TO_DISABLE, fclk_gate_lock);
+ enable_reg = readl(fclk_gate_reg) & 1;
+ if (enable & !enable_reg) {
+ if (clk_prepare_enable(clks[fclk]))
+ pr_warn("%s: FCLK%u enable failed\n", __func__,
+ fclk - fclk0);
+ }
kfree(mux_name);
kfree(div0_name);
kfree(div1_name);
@@ -213,6 +220,7 @@ static void __init zynq_clk_setup(struct device_node *np)
int ret;
struct clk *clk;
char *clk_name;
+ unsigned int fclk_enable;
const char *clk_output_name[clk_max];
const char *cpu_parents[4];
const char *periph_parents[4];
@@ -247,6 +255,10 @@ static void __init zynq_clk_setup(struct device_node *np)
ps_clk = clk_register_fixed_rate(NULL, "ps_clk", NULL, CLK_IS_ROOT,
tmp);
+ ret = of_property_read_u32(np, "fclk-enable", &fclk_enable);
+ if (ret)
+ fclk_enable = 0xf;
+
/* PLLs */
clk = clk_register_zynq_pll("armpll_int", "ps_clk", SLCR_ARMPLL_CTRL,
SLCR_PLL_STATUS, 0, &armpll_lock);
@@ -340,10 +352,12 @@ static void __init zynq_clk_setup(struct device_node *np)
clk_prepare_enable(clks[dci]);
/* Peripheral clocks */
- for (i = fclk0; i <= fclk3; i++)
+ for (i = fclk0; i <= fclk3; i++) {
+ int enable = !!(fclk_enable & BIT(i - fclk0));
zynq_clk_register_fclk(i, clk_output_name[i],
SLCR_FPGA0_CLK_CTRL + 0x10 * (i - fclk0),
- periph_parents);
+ periph_parents, enable);
+ }
zynq_clk_register_periph_clk(lqspi, 0, clk_output_name[lqspi], NULL,
SLCR_LQSPI_CLK_CTRL, periph_parents, 0);
--
1.8.4
Signed-off-by: Soren Brinkmann <[email protected]>
---
arch/arm/boot/dts/zynq-7000.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi
index e32b92b949d2..b48d0403537b 100644
--- a/arch/arm/boot/dts/zynq-7000.dtsi
+++ b/arch/arm/boot/dts/zynq-7000.dtsi
@@ -77,6 +77,7 @@
#clock-cells = <1>;
compatible = "xlnx,ps7-clkc";
ps-clk-frequency = <33333333>;
+ fclk-enable = <0>;
clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x",
"cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x",
"dci", "lqspi", "smc", "pcap", "gem0", "gem1",
--
1.8.4
On Tue, Oct 08, 2013 at 03:36:11PM +0100, Soren Brinkmann wrote:
> In some use cases Zynq's FPGA clocks are used as static clock
> generators for IP in the FPGA part of the SOC for which no Linux driver
> exists and would control those clocks. To avoid automatic
> gating of these clocks in such cases a new property - fclk-enable - is
> added to the clock controller's DT description to accomodate such use
> cases. It's value is a bitmask, where a set bit results in enabling
> the corresponding FCLK through the clkc.
>
> FPGA clocks are handled following the rules below:
>
> If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
> Linux. Drivers can enable and control it through the CCF as usual.
>
> If an FCLK is enabled by bootloaders AND the corresponding bit in the
> 'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
> resulting in an off by one reference count for that clock. Ensuring it
> will always be running.
>
> The default value for 'fclk-enable' is '0xf' (all FCLK's enabled by the
> bootloader are enabled through the clkc.
Why? Juding by the diff that's not what the code currently does, so why
not leave it as 0, and only set it where required as a work-around?
Thans,
Mark.
>
> Signed-off-by: Soren Brinkmann <[email protected]>
> ---
> .../devicetree/bindings/clock/zynq-7000.txt | 4 ++++
> drivers/clk/zynq/clkc.c | 20 +++++++++++++++++---
> 2 files changed, 21 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/clock/zynq-7000.txt b/Documentation/devicetree/bindings/clock/zynq-7000.txt
> index d99af878f5d7..11fdd146ec83 100644
> --- a/Documentation/devicetree/bindings/clock/zynq-7000.txt
> +++ b/Documentation/devicetree/bindings/clock/zynq-7000.txt
> @@ -22,6 +22,10 @@ Required properties:
> Optional properties:
> - clocks : as described in the clock bindings
> - clock-names : as described in the clock bindings
> + - fclk-enable : Bit mask to enable FCLKs in cases no proper CCF compatible
> + driver is available. Bit [0..3] correspond to FCLK0..FCLK3. The
> + corresponding FCLK will only be enabled if it is actually
> + running at boot time. (default = 0xf)
>
> Clock inputs:
> The following strings are optional parameters to the 'clock-names' property in
> diff --git a/drivers/clk/zynq/clkc.c b/drivers/clk/zynq/clkc.c
> index 10772aa72e4e..a36fc0f47634 100644
> --- a/drivers/clk/zynq/clkc.c
> +++ b/drivers/clk/zynq/clkc.c
> @@ -102,9 +102,10 @@ static const char *swdt_ext_clk_input_names[] __initdata = {"swdt_ext_clk"};
>
> static void __init zynq_clk_register_fclk(enum zynq_clk fclk,
> const char *clk_name, void __iomem *fclk_ctrl_reg,
> - const char **parents)
> + const char **parents, int enable)
> {
> struct clk *clk;
> + u32 enable_reg;
> char *mux_name;
> char *div0_name;
> char *div1_name;
> @@ -147,6 +148,12 @@ static void __init zynq_clk_register_fclk(enum zynq_clk fclk,
> clks[fclk] = clk_register_gate(NULL, clk_name,
> div1_name, CLK_SET_RATE_PARENT, fclk_gate_reg,
> 0, CLK_GATE_SET_TO_DISABLE, fclk_gate_lock);
> + enable_reg = readl(fclk_gate_reg) & 1;
> + if (enable & !enable_reg) {
> + if (clk_prepare_enable(clks[fclk]))
> + pr_warn("%s: FCLK%u enable failed\n", __func__,
> + fclk - fclk0);
> + }
> kfree(mux_name);
> kfree(div0_name);
> kfree(div1_name);
> @@ -213,6 +220,7 @@ static void __init zynq_clk_setup(struct device_node *np)
> int ret;
> struct clk *clk;
> char *clk_name;
> + unsigned int fclk_enable;
> const char *clk_output_name[clk_max];
> const char *cpu_parents[4];
> const char *periph_parents[4];
> @@ -247,6 +255,10 @@ static void __init zynq_clk_setup(struct device_node *np)
> ps_clk = clk_register_fixed_rate(NULL, "ps_clk", NULL, CLK_IS_ROOT,
> tmp);
>
> + ret = of_property_read_u32(np, "fclk-enable", &fclk_enable);
> + if (ret)
> + fclk_enable = 0xf;
> +
> /* PLLs */
> clk = clk_register_zynq_pll("armpll_int", "ps_clk", SLCR_ARMPLL_CTRL,
> SLCR_PLL_STATUS, 0, &armpll_lock);
> @@ -340,10 +352,12 @@ static void __init zynq_clk_setup(struct device_node *np)
> clk_prepare_enable(clks[dci]);
>
> /* Peripheral clocks */
> - for (i = fclk0; i <= fclk3; i++)
> + for (i = fclk0; i <= fclk3; i++) {
> + int enable = !!(fclk_enable & BIT(i - fclk0));
> zynq_clk_register_fclk(i, clk_output_name[i],
> SLCR_FPGA0_CLK_CTRL + 0x10 * (i - fclk0),
> - periph_parents);
> + periph_parents, enable);
> + }
>
> zynq_clk_register_periph_clk(lqspi, 0, clk_output_name[lqspi], NULL,
> SLCR_LQSPI_CLK_CTRL, periph_parents, 0);
> --
> 1.8.4
>
>
On Tue, Oct 08, 2013 at 04:38:17PM +0100, Mark Rutland wrote:
> On Tue, Oct 08, 2013 at 03:36:11PM +0100, Soren Brinkmann wrote:
> > In some use cases Zynq's FPGA clocks are used as static clock
> > generators for IP in the FPGA part of the SOC for which no Linux driver
> > exists and would control those clocks. To avoid automatic
> > gating of these clocks in such cases a new property - fclk-enable - is
> > added to the clock controller's DT description to accomodate such use
> > cases. It's value is a bitmask, where a set bit results in enabling
> > the corresponding FCLK through the clkc.
> >
> > FPGA clocks are handled following the rules below:
> >
> > If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
> > Linux. Drivers can enable and control it through the CCF as usual.
> >
> > If an FCLK is enabled by bootloaders AND the corresponding bit in the
> > 'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
> > resulting in an off by one reference count for that clock. Ensuring it
> > will always be running.
> >
> > The default value for 'fclk-enable' is '0xf' (all FCLK's enabled by the
> > bootloader are enabled through the clkc.
>
> Why? Juding by the diff that's not what the code currently does, so why
> not leave it as 0, and only set it where required as a work-around?
The default is set as described here:
[...]
> > + ret = of_property_read_u32(np, "fclk-enable", &fclk_enable);
> > + if (ret)
> > + fclk_enable = 0xf;
> > +
The default has been chosen this way, because it avoids trouble with
customers. Customers expect the FPGA clocks to be running, once they
configured them in the FPGA tools. If Linux gates them off for some
reason, it creates confusion and often ends up in customer support.
But in general I agree. It is kind of a work around and having zero as
default would be desirable. I'd leave this to Michal.
Sören
On 10/09/2013 05:25 PM, Sören Brinkmann wrote:
> On Tue, Oct 08, 2013 at 04:38:17PM +0100, Mark Rutland wrote:
>> On Tue, Oct 08, 2013 at 03:36:11PM +0100, Soren Brinkmann wrote:
>>> In some use cases Zynq's FPGA clocks are used as static clock
>>> generators for IP in the FPGA part of the SOC for which no Linux driver
>>> exists and would control those clocks. To avoid automatic
>>> gating of these clocks in such cases a new property - fclk-enable - is
>>> added to the clock controller's DT description to accomodate such use
>>> cases. It's value is a bitmask, where a set bit results in enabling
>>> the corresponding FCLK through the clkc.
>>>
>>> FPGA clocks are handled following the rules below:
>>>
>>> If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
>>> Linux. Drivers can enable and control it through the CCF as usual.
>>>
>>> If an FCLK is enabled by bootloaders AND the corresponding bit in the
>>> 'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
>>> resulting in an off by one reference count for that clock. Ensuring it
>>> will always be running.
>>>
>>> The default value for 'fclk-enable' is '0xf' (all FCLK's enabled by the
>>> bootloader are enabled through the clkc.
>>
>> Why? Juding by the diff that's not what the code currently does, so why
>> not leave it as 0, and only set it where required as a work-around?
> The default is set as described here:
> [...]
>>> + ret = of_property_read_u32(np, "fclk-enable", &fclk_enable);
>>> + if (ret)
>>> + fclk_enable = 0xf;
>>> +
>
> The default has been chosen this way, because it avoids trouble with
> customers. Customers expect the FPGA clocks to be running, once they
> configured them in the FPGA tools. If Linux gates them off for some
> reason, it creates confusion and often ends up in customer support.
> But in general I agree. It is kind of a work around and having zero as
> default would be desirable. I'd leave this to Michal.
No problem to have default value setup to 0. And use this workaround
when it is set in DTS.
Thanks,
Michal
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: http://www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform
On Thu, Oct 10, 2013 at 07:21:40AM +0200, Michal Simek wrote:
> On 10/09/2013 05:25 PM, Sören Brinkmann wrote:
> > On Tue, Oct 08, 2013 at 04:38:17PM +0100, Mark Rutland wrote:
> >> On Tue, Oct 08, 2013 at 03:36:11PM +0100, Soren Brinkmann wrote:
> >>> In some use cases Zynq's FPGA clocks are used as static clock
> >>> generators for IP in the FPGA part of the SOC for which no Linux driver
> >>> exists and would control those clocks. To avoid automatic
> >>> gating of these clocks in such cases a new property - fclk-enable - is
> >>> added to the clock controller's DT description to accomodate such use
> >>> cases. It's value is a bitmask, where a set bit results in enabling
> >>> the corresponding FCLK through the clkc.
> >>>
> >>> FPGA clocks are handled following the rules below:
> >>>
> >>> If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
> >>> Linux. Drivers can enable and control it through the CCF as usual.
> >>>
> >>> If an FCLK is enabled by bootloaders AND the corresponding bit in the
> >>> 'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
> >>> resulting in an off by one reference count for that clock. Ensuring it
> >>> will always be running.
> >>>
> >>> The default value for 'fclk-enable' is '0xf' (all FCLK's enabled by the
> >>> bootloader are enabled through the clkc.
> >>
> >> Why? Juding by the diff that's not what the code currently does, so why
> >> not leave it as 0, and only set it where required as a work-around?
> > The default is set as described here:
> > [...]
> >>> + ret = of_property_read_u32(np, "fclk-enable", &fclk_enable);
> >>> + if (ret)
> >>> + fclk_enable = 0xf;
> >>> +
> >
> > The default has been chosen this way, because it avoids trouble with
> > customers. Customers expect the FPGA clocks to be running, once they
> > configured them in the FPGA tools. If Linux gates them off for some
> > reason, it creates confusion and often ends up in customer support.
> > But in general I agree. It is kind of a work around and having zero as
> > default would be desirable. I'd leave this to Michal.
>
> No problem to have default value setup to 0. And use this workaround
> when it is set in DTS.
All right, I'll prepare v2 with that default changed to 0.
Sören