Hi folks
I have trouble with IT8212F raid controller (on Gigabyte boards also known
as GigaRaid) on FedoraCore 3.
There was some problem with building modules but after some fixing Makefile
I succeeded to build module.
After loading module dmesg shows:
Found Controller: IT8212 UDMA/ATA133 RAID Controller
FindDevices: device 0 is IDE
FindDevices: device 1 is IDE
Channel[0] BM-DMA at 0xA400-0xA407
Channel[1] BM-DMA at 0xA408-0xA40F
scsi2 : ITE RAIDExpress133
Vendor: ITE Model: IT8212F Rev: 1.3
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 488397166 512-byte hdwr sectors (250059 MB)
sdb: asking for cache data failed
sdb: assuming drive cache: write through
sdb: sdb1
Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
Vendor: ITE Model: IT8212F Rev: 1.3
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdc: 488397166 512-byte hdwr sectors (250059 MB)
sdc: asking for cache data failed
sdc: assuming drive cache: write through
sdc:<4>atkbd.c: Unknown key pressed (translated set 2, code 0x0 on
isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on
isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
sdc1
Attached scsi disk sdc at scsi2, channel 0, id 1, lun 0
[root@beowulf scsi]# mount /dev/sdb1 /mnt/
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
...
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
kjournald starting. Commit interval 5 seconds
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
I found a lot of messages with this subject but I didn't found any final
answer.
I also tried to use iteraid driver from mm tree but situation is same.
Thanks in a advice
Best regards Mile
On Tue, 16 Nov 2004 15:23:30 +0100, Mile Davidovic
<[email protected]> wrote:
> Hi folks
>
> I have trouble with IT8212F raid controller (on Gigabyte boards also known
> as GigaRaid) on FedoraCore 3.
Try the ac kernels.
Arjan has some RPMs for FC3.
http://marc.theaimsgroup.com/?l=linux-kernel&m=110060681900689&w=2
-Rahul
Thanks a lot.
When I rebuild iteraid driver it works without complaining. Now testing
begin.
Best regards Mile
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Rahul Karnik
Sent: Tuesday, November 16, 2004 4:17 PM
To: [email protected]
Cc: [email protected]
Subject: Re: ITERaid and atkbd
On Tue, 16 Nov 2004 15:23:30 +0100, Mile Davidovic
<[email protected]> wrote:
> Hi folks
>
> I have trouble with IT8212F raid controller (on Gigabyte boards also
> known as GigaRaid) on FedoraCore 3.
Try the ac kernels.
Arjan has some RPMs for FC3.
http://marc.theaimsgroup.com/?l=linux-kernel&m=110060681900689&w=2
-Rahul