On Wed, 19 May 2021, at 10:28, Joel Stanley wrote:
> On Wed, 19 May 2021 at 00:07, Andrew Jeffery <[email protected]> wrote:
> >
> > Aspeed Virtual UARTs directly bridge e.g. the system console UART on the
> > LPC bus to the UART interface on the BMC's internal APB. As such there's
> > no RS-232 signalling involved - the UART interfaces on each bus are
> > directly connected as the producers and consumers of the one set of
> > FIFOs.
> >
> > The APB in the AST2600 generally runs at 100MHz while the LPC bus peaks
> > at 33MHz. The difference in clock speeds exposes a race in the VUART
> > design where a Tx data burst on the APB interface can result in a byte
> > lost on the LPC interface. The symptom is LSR[DR] remains clear on the
> > LPC interface despite data being present in its Rx FIFO, while LSR[THRE]
> > remains clear on the APB interface as the host has not consumed the data
> > the BMC has transmitted. In this state, the UART has stalled and no
> > further data can be transmitted without manual intervention (e.g.
> > resetting the FIFOs, resulting in loss of data).
> >
> > The recommended work-around is to insert a read cycle on the APB
> > interface between writes to THR.
> >
> > Cc: ChiaWei Wang <[email protected]>
> > Signed-off-by: Andrew Jeffery <[email protected]>
>
> Reviewed-by: Joel Stanley <[email protected]>
>
> > ---
> > drivers/tty/serial/8250/8250.h | 1 +
> > drivers/tty/serial/8250/8250_aspeed_vuart.c | 1 +
> > drivers/tty/serial/8250/8250_port.c | 10 ++++++++++
> > 3 files changed, 12 insertions(+)
> >
> > diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
> > index 52bb21205bb6..34aa2714f3c9 100644
> > --- a/drivers/tty/serial/8250/8250.h
> > +++ b/drivers/tty/serial/8250/8250.h
> > @@ -88,6 +88,7 @@ struct serial8250_config {
> > #define UART_BUG_NOMSR (1 << 2) /* UART has buggy MSR status bits (Au1x00) */
> > #define UART_BUG_THRE (1 << 3) /* UART has buggy THRE reassertion */
> > #define UART_BUG_PARITY (1 << 4) /* UART mishandles parity if FIFO enabled */
> > +#define UART_BUG_TXRACE (1 << 5) /* UART Tx fails to set remote DR */
> >
> >
> > #ifdef CONFIG_SERIAL_8250_SHARE_IRQ
> > diff --git a/drivers/tty/serial/8250/8250_aspeed_vuart.c b/drivers/tty/serial/8250/8250_aspeed_vuart.c
> > index a28a394ba32a..4caab8714e2c 100644
> > --- a/drivers/tty/serial/8250/8250_aspeed_vuart.c
> > +++ b/drivers/tty/serial/8250/8250_aspeed_vuart.c
> > @@ -440,6 +440,7 @@ static int aspeed_vuart_probe(struct platform_device *pdev)
> > port.port.status = UPSTAT_SYNC_FIFO;
> > port.port.dev = &pdev->dev;
> > port.port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_8250_CONSOLE);
> > + port.bugs |= UART_BUG_TXRACE;
>
> A future enhancement would be to have this depend on the ast2600
> compatible string, so we don't enable the feature for ast2400/ast2500.
>
> That would also mean adding a compatible string for the ast2600.
Yep, I'll sort out some cleanups in that regard in a separate series.
Andrew