From: Alexandru Tachici <[email protected]>
The ADIN1110 is a low power single port 10BASE-T1L MAC-PHY
designed for industrial Ethernet applications. It integrates
an Ethernet PHY core with a MAC and all the associated analog
circuitry, input and output clock buffering.
ADIN1110 MAC-PHY encapsulates the ADIN1100 PHY. The PHY registers
can be accessed through the MDIO MAC registers.
We are registering an MDIO bus with custom read/write in order
to let the PHY to be discovered by the PAL. This will let
the ADIN1100 Linux driver to probe and take control of
the PHY.
The ADIN2111 is a low power, low complexity, two-Ethernet ports
switch with integrated 10BASE-T1L PHYs and one serial peripheral
interface (SPI) port.
The device is designed for industrial Ethernet applications using
low power constrained nodes and is compliant with the IEEE 802.3cg-2019
Ethernet standard for long reach 10 Mbps single pair Ethernet (SPE).
The switch supports various routing configurations between
the two Ethernet ports and the SPI host port providing a flexible
solution for line, daisy-chain, or ring network topologies.
The ADIN2111 supports cable reach of up to 1700 meters with ultra
low power consumption of 77 mW. The two PHY cores support the
1.0 V p-p operating mode and the 2.4 V p-p operating mode defined
in the IEEE 802.3cg standard.
The device integrates the switch, two Ethernet physical layer (PHY)
cores with a media access control (MAC) interface and all the
associated analog circuitry, and input and output clock buffering.
The device also includes internal buffer queues, the SPI and
subsystem registers, as well as the control logic to manage the reset
and clock control and hardware pin configuration.
Access to the PHYs is exposed via an internal MDIO bus. Writes/reads
can be performed by reading/writing to the ADIN2111 MDIO registers
via SPI.
On probe, for each port, a struct net_device is allocated and
registered. When both ports are added to the same bridge, the driver
will enable offloading of frame forwarding at the hardware level.
Co-developed-by: Lennart Franzen <[email protected]>
Signed-off-by: Lennart Franzen <[email protected]>
Signed-off-by: Alexandru Tachici <[email protected]>
---
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/adi/Kconfig | 28 +
drivers/net/ethernet/adi/Makefile | 6 +
drivers/net/ethernet/adi/adin1110.c | 1312 +++++++++++++++++++++++++++
5 files changed, 1348 insertions(+)
create mode 100644 drivers/net/ethernet/adi/Kconfig
create mode 100644 drivers/net/ethernet/adi/Makefile
create mode 100644 drivers/net/ethernet/adi/adin1110.c
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index 955abbc5490e..954cd8c96032 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -120,6 +120,7 @@ config LANTIQ_XRX200
Support for the PMAC of the Gigabit switch (GSWIP) inside the
Lantiq / Intel VRX200 VDSL SoC
+source "drivers/net/ethernet/adi/Kconfig"
source "drivers/net/ethernet/litex/Kconfig"
source "drivers/net/ethernet/marvell/Kconfig"
source "drivers/net/ethernet/mediatek/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 9eb01169957f..bc65ca0d9b4c 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_NET_VENDOR_8390) += 8390/
obj-$(CONFIG_NET_VENDOR_ACTIONS) += actions/
obj-$(CONFIG_NET_VENDOR_ADAPTEC) += adaptec/
obj-$(CONFIG_GRETH) += aeroflex/
+obj-$(CONFIG_NET_VENDOR_ADI) += adi/
obj-$(CONFIG_NET_VENDOR_AGERE) += agere/
obj-$(CONFIG_NET_VENDOR_ALACRITECH) += alacritech/
obj-$(CONFIG_NET_VENDOR_ALLWINNER) += allwinner/
diff --git a/drivers/net/ethernet/adi/Kconfig b/drivers/net/ethernet/adi/Kconfig
new file mode 100644
index 000000000000..da3bdd302502
--- /dev/null
+++ b/drivers/net/ethernet/adi/Kconfig
@@ -0,0 +1,28 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+#
+# Analog Devices device configuration
+#
+
+config NET_VENDOR_ADI
+ bool "Analog Devices devices"
+ default y
+ depends on SPI
+ help
+ If you have a network (Ethernet) card belonging to this class, say Y.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about ADI devices. If you say Y, you will be asked
+ for your specific card in the following questions.
+
+if NET_VENDOR_ADI
+
+config ADIN1110
+ tristate "Analog Devices ADIN1110 MAC-PHY"
+ depends on SPI && NET_SWITCHDEV
+ select CRC8
+ help
+ Say yes here to build support for Analog Devices ADIN1110
+ Low Power 10BASE-T1L Ethernet MAC-PHY.
+
+endif # NET_VENDOR_ADI
diff --git a/drivers/net/ethernet/adi/Makefile b/drivers/net/ethernet/adi/Makefile
new file mode 100644
index 000000000000..d0383d94303c
--- /dev/null
+++ b/drivers/net/ethernet/adi/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+#
+# Makefile for the Analog Devices network device drivers.
+#
+
+obj-$(CONFIG_ADIN1110) += adin1110.o
diff --git a/drivers/net/ethernet/adi/adin1110.c b/drivers/net/ethernet/adi/adin1110.c
new file mode 100644
index 000000000000..fdefd6fdeb9d
--- /dev/null
+++ b/drivers/net/ethernet/adi/adin1110.c
@@ -0,0 +1,1312 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+/* ADIN1110 Low Power 10BASE-T1L Ethernet MAC-PHY
+ * ADIN2111 2-Port Ethernet Switch with Integrated 10BASE-T1L PHY
+ *
+ * Copyright 2021 Analog Devices Inc.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/cache.h>
+#include <linux/crc8.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/mii.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/regulator/consumer.h>
+#include <linux/phy.h>
+#include <linux/property.h>
+#include <linux/spi/spi.h>
+
+#include <asm/unaligned.h>
+
+#define ADIN1110_PHY_ID 0x1
+
+#define ADIN1110_RESET 0x03
+#define ADIN1110_SWRESET BIT(0)
+
+#define ADIN1110_CONFIG1 0x04
+#define ADIN1110_CONFIG1_SYNC BIT(15)
+
+#define ADIN1110_CONFIG2 0x06
+#define ADIN2111_FWD_UNK2PORT GENMASK(14, 13)
+#define ADIN2111_P2_FWD_UNK2HOST BIT(12)
+#define ADIN1110_CRC_APPEND BIT(5)
+#define ADIN1110_FWD_UNK2HOST BIT(2)
+
+#define ADIN1110_STATUS0 0x08
+
+#define ADIN1110_STATUS1 0x09
+#define ADIN2111_P2_RX_RDY BIT(17)
+#define ADIN1110_SPI_ERR BIT(10)
+#define ADIN1110_RX_RDY BIT(4)
+#define ADIN1110_TX_RDY BIT(3)
+
+#define ADIN1110_IMASK1 0x0D
+#define ADIN2111_RX_RDY_IRQ BIT(17)
+#define ADIN1110_SPI_ERR_IRQ BIT(10)
+#define ADIN1110_RX_RDY_IRQ BIT(4)
+#define ADIN1110_TX_RDY_IRQ BIT(3)
+
+#define ADIN1110_MDIOACC 0x20
+#define ADIN1110_MDIO_TRDONE BIT(31)
+#define ADIN1110_MDIO_TAERR BIT(30)
+#define ADIN1110_MDIO_ST GENMASK(29, 28)
+#define ADIN1110_MDIO_OP GENMASK(27, 26)
+#define ADIN1110_MDIO_PRTAD GENMASK(25, 21)
+#define ADIN1110_MDIO_DEVAD GENMASK(20, 16)
+#define ADIN1110_MDIO_DATA GENMASK(15, 0)
+
+#define ADIN1110_TX_FSIZE 0x30
+#define ADIN1110_TX 0x31
+#define ADIN1110_TX_SPACE 0x32
+#define ADIN1110_RX_THRESH 0x33
+#define ADIN1110_TX_THRESH 0x34
+
+#define ADIN1110_FIFO_CLR 0x36
+#define ADIN1110_FIFO_SIZE 0x3E
+#define ADIN1110_TFC 0x3F
+
+#define ADIN1110_MAC_ADDR_FILTER_UPR 0x50
+#define ADIN2111_MAC_ADDR_APPLY2PORT2 BIT(31)
+#define ADIN1110_MAC_ADDR_APPLY2PORT BIT(30)
+#define ADIN1110_MAC_ADDR_HOST_PRI BIT(19)
+#define ADIN2111_MAC_ADDR_TO_OTHER_PORT BIT(17)
+#define ADIN1110_MAC_ADDR_TO_HOST BIT(16)
+#define ADIN1110_MAC_ADDR GENMASK(15, 0)
+
+#define ADIN1110_MAC_ADDR_FILTER_LWR 0x51
+
+#define ADIN1110_MAC_ADDR_MASK_UPR 0x70
+#define ADIN1110_MAC_ADDR_MASK_LWR 0x71
+
+#define ADIN1110_RX_FSIZE 0x90
+#define ADIN1110_RX 0x91
+
+#define ADIN1110_RX_FRM_CNT(x) (0xA0 + ((x) * 0x30))
+#define ADIN1110_RX_MCAST_CNT(x) (0xA2 + ((x) * 0x30))
+#define ADIN1110_RX_CRC_ERR_CNT(x) (0xA4 + ((x) * 0x30))
+#define ADIN1110_RX_ALGN_ERR_CNT(x) (0xA5 + ((x) * 0x30))
+#define ADIN1110_RX_LS_ERR_CNT(x) (0xA6 + ((x) * 0x30))
+#define ADIN1110_RX_PHY_ERR_CNT(x) (0xA7 + ((x) * 0x30))
+#define ADIN1110_RX_DROP_FULL_CNT(x) (0xAC + ((x) * 0x30))
+
+#define ADIN1110_TX_FRM_CNT(x) (0xA8 + ((x) * 0x30))
+#define ADIN1110_TX_MCAST_CNT(x) (0xAA + ((x) * 0x30))
+
+#define ADIN2111_RX_P2_FSIZE 0xC0
+#define ADIN2111_RX_P2 0xC1
+
+#define ADIN1110_CLEAR_STATUS0 0xFFF
+#define ADIN1110_CLEAR_STATUS1 U32_MAX
+
+/* MDIO_OP codes */
+#define ADIN1110_MDIO_OP_WR 0x1
+#define ADIN1110_MDIO_OP_RD 0x3
+
+#define ADIN1110_CD BIT(7)
+#define ADIN1110_WRITE BIT(5)
+
+#define ADIN1110_MAX_BUFF 2048
+#define ADIN1110_WR_HEADER_LEN 2
+#define ADIN1110_FRAME_HEADER_LEN 2
+#define ADIN1110_INTERNAL_SIZE_HEADER_LEN 2
+#define ADIN1110_RD_HEADER_LEN 3
+#define ADIN1110_REG_LEN 4
+#define ADIN1110_FEC_LEN 4
+
+#define ADIN1110_PHY_ID_VAL 0x0283BC91
+#define ADIN2111_PHY_ID_VAL 0x0283BCA1
+
+#define ADIN1110_TX_SPACE_MAX 0x0FFF
+
+#define ADIN_MAC_MAX_PORTS 2
+
+#define ADIN_MAC_MULTICAST_ADDR_SLOT 0
+#define ADIN_MAC_ADDR_SLOT 1
+#define ADIN_MAC_BROADCAST_ADDR_SLOT 2
+
+DECLARE_CRC8_TABLE(adin1110_crc_table);
+
+enum adin1110_chips_id {
+ ADIN1110_MAC = 0,
+ ADIN2111_MAC,
+};
+
+struct adin1110_cfg {
+ enum adin1110_chips_id id;
+ char name[MDIO_NAME_SIZE];
+ u32 phy_ids[PHY_MAX_ADDR];
+ u32 ports_nr;
+ u32 phy_id_val;
+};
+
+struct adin1110_port_priv {
+ struct adin1110_priv *priv;
+ struct net_device *netdev;
+ struct net_device *bridge;
+ struct phy_device *phydev;
+ struct work_struct tx_work;
+ u64 rx_bytes;
+ u64 tx_bytes;
+ struct work_struct rx_mode_work;
+ u32 flags;
+ struct sk_buff_head txq;
+ u32 nr;
+ struct adin1110_cfg *cfg;
+};
+
+struct adin1110_priv {
+ struct mutex lock; /* protect spi */
+ spinlock_t state_lock; /* protect RX mode */
+ bool forwarding;
+ struct mii_bus *mii_bus;
+ struct spi_device *spidev;
+ bool append_crc;
+ struct adin1110_cfg *cfg;
+ u32 tx_space;
+ u32 irq_mask;
+ int irq;
+ struct adin1110_port_priv *ports[ADIN_MAC_MAX_PORTS];
+ char mii_bus_name[MII_BUS_ID_SIZE];
+ u8 data[ADIN1110_MAX_BUFF] ____cacheline_aligned;
+};
+
+struct adin1110_cfg adin1110_cfgs[] = {
+ {
+ .id = ADIN1110_MAC,
+ .name = "adin1110",
+ .phy_ids = {1},
+ .ports_nr = 1,
+ .phy_id_val = ADIN1110_PHY_ID_VAL,
+ },
+ {
+ .id = ADIN2111_MAC,
+ .name = "adin2111",
+ .phy_ids = {1, 2},
+ .ports_nr = 2,
+ .phy_id_val = ADIN2111_PHY_ID_VAL,
+ },
+};
+
+static u8 adin1110_crc_data(u8 *data, u32 len)
+{
+ return crc8(adin1110_crc_table, data, len, 0);
+}
+
+static int adin1110_read_reg(struct adin1110_priv *priv, u16 reg, u32 *val)
+{
+ struct spi_transfer t[2] = {0};
+ __le16 __reg = cpu_to_le16(reg);
+ u32 header_len = ADIN1110_RD_HEADER_LEN;
+ u32 read_len = ADIN1110_REG_LEN;
+ int ret;
+
+ priv->data[0] = ADIN1110_CD | FIELD_GET(GENMASK(12, 8), __reg);
+ priv->data[1] = FIELD_GET(GENMASK(7, 0), __reg);
+ priv->data[2] = 0x00;
+
+ if (priv->append_crc) {
+ priv->data[2] = adin1110_crc_data(&priv->data[0], 2);
+ priv->data[3] = 0x00;
+ header_len++;
+ }
+
+ t[0].tx_buf = &priv->data[0];
+ t[0].len = header_len;
+
+ if (priv->append_crc)
+ read_len++;
+
+ memset(&priv->data[header_len], 0, read_len);
+ t[1].rx_buf = &priv->data[header_len];
+ t[1].len = read_len;
+
+ ret = spi_sync_transfer(priv->spidev, t, 2);
+ if (ret)
+ return ret;
+
+ if (priv->append_crc) {
+ u8 recv_crc;
+ u8 crc;
+
+ crc = adin1110_crc_data(&priv->data[header_len], ADIN1110_REG_LEN);
+ recv_crc = priv->data[header_len + ADIN1110_REG_LEN];
+
+ if (crc != recv_crc) {
+ dev_err(&priv->spidev->dev, "CRC error.");
+ return -EBADMSG;
+ }
+ }
+
+ *val = get_unaligned_be32(&priv->data[header_len]);
+
+ return ret;
+}
+
+static int adin1110_write_reg(struct adin1110_priv *priv, u16 reg, u32 val)
+{
+ u32 header_len = ADIN1110_WR_HEADER_LEN;
+ u32 write_len = ADIN1110_REG_LEN;
+ __le16 __reg = cpu_to_le16(reg);
+
+ priv->data[0] = ADIN1110_CD | ADIN1110_WRITE | FIELD_GET(GENMASK(12, 8), __reg);
+ priv->data[1] = FIELD_GET(GENMASK(7, 0), __reg);
+
+ if (priv->append_crc) {
+ priv->data[2] = adin1110_crc_data(&priv->data[0], header_len);
+ header_len++;
+ }
+
+ put_unaligned_be32(val, &priv->data[header_len]);
+ if (priv->append_crc) {
+ priv->data[header_len + write_len] = adin1110_crc_data(&priv->data[header_len],
+ write_len);
+ write_len++;
+ }
+
+ return spi_write(priv->spidev, &priv->data[0], header_len + write_len);
+}
+
+static int adin1110_set_bits(struct adin1110_priv *priv, u16 reg, unsigned long mask,
+ unsigned long val)
+{
+ u32 write_val;
+ int ret;
+
+ ret = adin1110_read_reg(priv, reg, &write_val);
+ if (ret < 0)
+ return ret;
+
+ set_mask_bits(&write_val, mask, val);
+
+ return adin1110_write_reg(priv, reg, write_val);
+}
+
+static int adin1110_round_len(int len)
+{
+ /* can read/write only mutiples of 4 bytes of payload */
+ len = ALIGN(len, 4);
+
+ /* NOTE: ADIN1110_WR_HEADER_LEN should be used for write ops. */
+ if (len + ADIN1110_RD_HEADER_LEN > ADIN1110_MAX_BUFF)
+ return -EINVAL;
+
+ return len;
+}
+
+static int adin1110_read_fifo(struct adin1110_port_priv *port_priv)
+{
+ struct adin1110_priv *priv = port_priv->priv;
+ u32 header_len = ADIN1110_RD_HEADER_LEN;
+ struct spi_transfer t[2] = {0};
+ u32 frame_size_no_fcs;
+ struct sk_buff *rxb;
+ u32 frame_size;
+ int round_len;
+ __le16 __reg;
+ int ret;
+
+ if (!port_priv->nr) {
+ __reg = cpu_to_le16(ADIN1110_RX);
+ ret = adin1110_read_reg(priv, ADIN1110_RX_FSIZE, &frame_size);
+ } else {
+ __reg = cpu_to_le16(ADIN2111_RX_P2);
+ ret = adin1110_read_reg(priv, ADIN2111_RX_P2_FSIZE, &frame_size);
+ }
+
+ if (ret < 0)
+ return ret;
+
+ /* the read frame size includes the extra 2 bytes from the ADIN1110 frame header */
+ if (frame_size < ADIN1110_FRAME_HEADER_LEN + ADIN1110_FEC_LEN)
+ return ret;
+
+ round_len = adin1110_round_len(frame_size);
+ if (round_len < 0)
+ return ret;
+
+ frame_size_no_fcs = frame_size - ADIN1110_FRAME_HEADER_LEN - ADIN1110_FEC_LEN;
+
+ rxb = netdev_alloc_skb(port_priv->netdev, frame_size_no_fcs);
+ if (!rxb)
+ return -ENOMEM;
+
+ memset(priv->data, 0, round_len + ADIN1110_RD_HEADER_LEN);
+
+ priv->data[0] = ADIN1110_CD | FIELD_GET(GENMASK(12, 8), __reg);
+ priv->data[1] = FIELD_GET(GENMASK(7, 0), __reg);
+ priv->data[2] = 0x00;
+
+ if (priv->append_crc) {
+ priv->data[2] = adin1110_crc_data(&priv->data[0], 2);
+ priv->data[3] = 0x00;
+ header_len++;
+ }
+
+ t[0].tx_buf = &priv->data[0];
+ t[0].len = header_len;
+
+ t[1].rx_buf = &priv->data[header_len];
+ t[1].len = round_len;
+
+ ret = spi_sync_transfer(priv->spidev, t, 2);
+ if (ret) {
+ kfree_skb(rxb);
+ return ret;
+ }
+
+ /* Already forwarded to the other port if it did not match any MAC Addresses. */
+ if (priv->forwarding)
+ rxb->offload_fwd_mark = 1;
+
+ skb_put(rxb, frame_size_no_fcs);
+ skb_copy_to_linear_data(rxb, &priv->data[header_len + ADIN1110_FRAME_HEADER_LEN],
+ frame_size_no_fcs);
+
+ rxb->protocol = eth_type_trans(rxb, port_priv->netdev);
+
+ netif_rx(rxb);
+
+ port_priv->rx_bytes += frame_size - ADIN1110_FRAME_HEADER_LEN;
+
+ return 0;
+}
+
+static int adin1110_write_fifo(struct adin1110_port_priv *port_priv, struct sk_buff *txb)
+{
+ struct adin1110_priv *priv = port_priv->priv;
+ __le16 __reg = cpu_to_le16(ADIN1110_TX);
+ u32 header_len = ADIN1110_WR_HEADER_LEN;
+ __be16 frame_header;
+ int padding = 0;
+ int round_len;
+ int padded_len;
+ int ret;
+
+ /* Pad frame to 64 byte length,
+ * MAC nor PHY will otherwise add the
+ * required padding.
+ * The FEC will be added by the MAC internally.
+ */
+ if (txb->len + ADIN1110_FEC_LEN < 64)
+ padding = 64 - (txb->len + ADIN1110_FEC_LEN);
+
+ padded_len = txb->len + padding + ADIN1110_FRAME_HEADER_LEN;
+
+ round_len = adin1110_round_len(padded_len);
+ if (round_len < 0)
+ return round_len;
+
+ ret = adin1110_write_reg(priv, ADIN1110_TX_FSIZE, padded_len);
+ if (ret < 0)
+ return ret;
+
+ memset(priv->data, 0, round_len + ADIN1110_WR_HEADER_LEN);
+
+ priv->data[0] = ADIN1110_CD | ADIN1110_WRITE | FIELD_GET(GENMASK(12, 8), __reg);
+ priv->data[1] = FIELD_GET(GENMASK(7, 0), __reg);
+ if (priv->append_crc) {
+ priv->data[2] = adin1110_crc_data(&priv->data[0], 2);
+ header_len++;
+ }
+
+ /* mention the port on which to send the frame in the frame header */
+ frame_header = cpu_to_be16(port_priv->nr);
+ memcpy(&priv->data[header_len], &frame_header, ADIN1110_FRAME_HEADER_LEN);
+
+ memcpy(&priv->data[header_len + ADIN1110_FRAME_HEADER_LEN], txb->data, txb->len);
+
+ ret = spi_write(priv->spidev, &priv->data[0], round_len + header_len);
+ if (ret < 0)
+ return ret;
+
+ port_priv->tx_bytes += txb->len;
+
+ return 0;
+}
+
+static int adin1110_read_mdio_acc(struct adin1110_priv *priv)
+{
+ u32 val;
+ int ret;
+
+ ret = adin1110_read_reg(priv, ADIN1110_MDIOACC, &val);
+ if (ret < 0)
+ return 0;
+
+ return val;
+}
+
+static int adin1110_mdio_read(struct mii_bus *bus, int phy_id, int reg)
+{
+ struct adin1110_priv *priv = bus->priv;
+ u32 val = 0;
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ val |= FIELD_PREP(ADIN1110_MDIO_OP, ADIN1110_MDIO_OP_RD);
+ val |= FIELD_PREP(ADIN1110_MDIO_ST, 0x1);
+ val |= FIELD_PREP(ADIN1110_MDIO_PRTAD, phy_id);
+ val |= FIELD_PREP(ADIN1110_MDIO_DEVAD, reg);
+
+ /* write the clause 22 read command to the chip */
+ ret = adin1110_write_reg(priv, ADIN1110_MDIOACC, val);
+ if (ret < 0) {
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ /* ADIN1110_MDIO_TRDONE BIT of the ADIN1110_MDIOACC
+ * register is set when the read is done.
+ * After the transaction is done, ADIN1110_MDIO_DATA
+ * bitfield of ADIN1110_MDIOACC register will contain
+ * the requested register value.
+ */
+ ret = readx_poll_timeout(adin1110_read_mdio_acc, priv, val, (val & ADIN1110_MDIO_TRDONE),
+ 10000, 30000);
+ mutex_unlock(&priv->lock);
+
+ if (ret < 0)
+ return ret;
+
+ return (val & ADIN1110_MDIO_DATA);
+}
+
+static int adin1110_mdio_write(struct mii_bus *bus, int phy_id, int reg, u16 reg_val)
+{
+ struct adin1110_priv *priv = bus->priv;
+ u32 val = 0;
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ val |= FIELD_PREP(ADIN1110_MDIO_OP, ADIN1110_MDIO_OP_WR);
+ val |= FIELD_PREP(ADIN1110_MDIO_ST, 0x1);
+ val |= FIELD_PREP(ADIN1110_MDIO_PRTAD, phy_id);
+ val |= FIELD_PREP(ADIN1110_MDIO_DEVAD, reg);
+ val |= FIELD_PREP(ADIN1110_MDIO_DATA, reg_val);
+
+ /* write the clause 22 write command to the chip */
+ ret = adin1110_write_reg(priv, ADIN1110_MDIOACC, val);
+ if (ret < 0) {
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ ret = readx_poll_timeout(adin1110_read_mdio_acc, priv, val, (val & ADIN1110_MDIO_TRDONE),
+ 10000, 30000);
+ mutex_unlock(&priv->lock);
+
+ return ret;
+}
+
+/* ADIN1110 MAC-PHY contains an ADIN1100 PHY.
+ * ADIN2111 MAC-PHY contains two ADIN1100 PHYs.
+ * By registering a new MDIO bus we allow the PAL to discover
+ * the encapsulated PHY and probe the ADIN1100 driver.
+ */
+static int adin1110_register_mdiobus(struct adin1110_priv *priv, struct device *dev)
+{
+ struct mii_bus *mii_bus;
+ int ret;
+
+ mii_bus = devm_mdiobus_alloc(dev);
+ if (!mii_bus)
+ return -ENOMEM;
+
+ snprintf(priv->mii_bus_name, MII_BUS_ID_SIZE, "%s-%u",
+ priv->cfg->name, priv->spidev->chip_select);
+
+ mii_bus->name = priv->mii_bus_name;
+ mii_bus->read = adin1110_mdio_read;
+ mii_bus->write = adin1110_mdio_write;
+ mii_bus->priv = priv;
+ mii_bus->parent = dev;
+ mii_bus->phy_mask = ~((u32)GENMASK(2, 0));
+ snprintf(mii_bus->id, MII_BUS_ID_SIZE, "%s", dev_name(dev));
+
+ ret = devm_mdiobus_register(dev, mii_bus);
+ if (ret)
+ return ret;
+
+ priv->mii_bus = mii_bus;
+
+ return 0;
+}
+
+static bool adin1110_port_rx_ready(struct adin1110_port_priv *port_priv, u32 status)
+{
+ if (!port_priv->nr)
+ return !!(status & ADIN1110_RX_RDY);
+ else
+ return !!(status & ADIN2111_P2_RX_RDY);
+}
+
+static void adin1110_read_frames(struct adin1110_port_priv *port_priv)
+{
+ struct adin1110_priv *priv = port_priv->priv;
+ u32 status1;
+ int ret;
+
+ while (1) {
+ ret = adin1110_read_reg(priv, ADIN1110_STATUS1, &status1);
+ if (ret < 0)
+ return;
+
+ if (!adin1110_port_rx_ready(port_priv, status1))
+ break;
+
+ ret = adin1110_read_fifo(port_priv);
+ if (ret < 0)
+ return;
+ }
+}
+
+static void adin1110_wake_queues(struct adin1110_priv *priv)
+{
+ int i;
+
+ for (i = 0; i < priv->cfg->ports_nr; i++)
+ netif_wake_queue(priv->ports[i]->netdev);
+}
+
+static irqreturn_t adin1110_irq(int irq, void *p)
+{
+ struct adin1110_priv *priv = p;
+ u32 status1;
+ u32 val;
+ int ret;
+ int i;
+
+ mutex_lock(&priv->lock);
+
+ adin1110_read_reg(priv, ADIN1110_STATUS1, &status1);
+
+ if (priv->append_crc && (status1 & ADIN1110_SPI_ERR))
+ dev_warn(&priv->spidev->dev, "SPI CRC error on write.\n");
+
+ ret = adin1110_read_reg(priv, ADIN1110_TX_SPACE, &val);
+ if (ret < 0) {
+ mutex_unlock(&priv->lock);
+ return IRQ_HANDLED;
+ }
+
+ /* TX FIFO space is expressed in half-words */
+ priv->tx_space = 2 * val;
+
+ for (i = 0; i < priv->cfg->ports_nr; i++) {
+ if (adin1110_port_rx_ready(priv->ports[i], status1))
+ adin1110_read_frames(priv->ports[i]);
+ }
+
+ /* clear IRQ sources */
+ ret = adin1110_write_reg(priv, ADIN1110_STATUS0, ADIN1110_CLEAR_STATUS0);
+ ret = adin1110_write_reg(priv, ADIN1110_STATUS1, priv->irq_mask);
+
+ mutex_unlock(&priv->lock);
+
+ if (priv->tx_space > 0)
+ adin1110_wake_queues(priv);
+
+ return IRQ_HANDLED;
+}
+
+/* ADIN1110 can filter up to 16 MAC addresses, mac_nr here is the slot used */
+static int adin1110_write_mac_address(struct adin1110_port_priv *port_priv, int mac_nr,
+ const u8 *addr, u8 *mask)
+{
+ struct adin1110_priv *priv = port_priv->priv;
+ u32 offset = mac_nr * 2;
+ u32 port_rules;
+ int ret;
+ u32 val;
+
+ port_rules = ADIN1110_MAC_ADDR_APPLY2PORT;
+ if (priv->cfg->id == ADIN2111_MAC) {
+ port_rules |= ADIN2111_MAC_ADDR_APPLY2PORT2;
+
+ if (mac_nr != ADIN_MAC_ADDR_SLOT && priv->forwarding)
+ port_rules |= ADIN2111_MAC_ADDR_TO_OTHER_PORT;
+ }
+
+ /* tell MAC to forward this DA to host */
+ val = port_rules | ADIN1110_MAC_ADDR_TO_HOST;
+ val |= get_unaligned_be16(&addr[0]);
+ ret = adin1110_write_reg(priv, ADIN1110_MAC_ADDR_FILTER_UPR + offset, val);
+ if (ret < 0)
+ return ret;
+
+ val = get_unaligned_be32(&addr[2]);
+ ret = adin1110_write_reg(priv, ADIN1110_MAC_ADDR_FILTER_LWR + offset, val);
+ if (ret < 0)
+ return ret;
+
+ /* only the first two MAC address slots support masking */
+ if (mac_nr < ADIN_MAC_BROADCAST_ADDR_SLOT) {
+ val = get_unaligned_be16(&mask[0]);
+ ret = adin1110_write_reg(priv, ADIN1110_MAC_ADDR_MASK_UPR + offset, val);
+ if (ret < 0)
+ return ret;
+
+ val = get_unaligned_be32(&mask[2]);
+ return adin1110_write_reg(priv, ADIN1110_MAC_ADDR_MASK_LWR + offset, val);
+ }
+
+ return 0;
+}
+
+static int adin1110_clear_mac_address(struct adin1110_port_priv *port_priv, int mac_nr)
+{
+ struct adin1110_priv *priv = port_priv->priv;
+ u32 offset = mac_nr * 2;
+ int ret;
+
+ ret = adin1110_write_reg(priv, ADIN1110_MAC_ADDR_FILTER_UPR + offset, 0);
+ if (ret < 0)
+ return ret;
+
+ ret = adin1110_write_reg(priv, ADIN1110_MAC_ADDR_FILTER_LWR + offset, 0);
+ if (ret < 0)
+ return ret;
+
+ ret = adin1110_write_reg(priv, ADIN1110_MAC_ADDR_MASK_UPR + offset, 0);
+ if (ret < 0)
+ return ret;
+
+ return adin1110_write_reg(priv, ADIN1110_MAC_ADDR_MASK_LWR + offset, 0);
+}
+
+static int adin1110_multicast_filter(struct adin1110_port_priv *port_priv, int mac_nr,
+ bool accept_multicast)
+{
+ u8 mask[ETH_ALEN] = {0};
+ u8 mac[ETH_ALEN] = {0};
+
+ if (accept_multicast) {
+ mask[0] = BIT(0);
+ mac[0] = BIT(0);
+
+ return adin1110_write_mac_address(port_priv, mac_nr, mac, mask);
+ }
+
+ return adin1110_clear_mac_address(port_priv, mac_nr);
+}
+
+static int adin1110_set_mac_address(struct net_device *netdev, void *addr)
+{
+ struct adin1110_port_priv *port_priv = netdev_priv(netdev);
+ struct sockaddr *sa = addr;
+ u8 mask[ETH_ALEN];
+
+ if (netif_running(netdev))
+ return -EBUSY;
+
+ if (!is_valid_ether_addr(sa->sa_data))
+ return -EADDRNOTAVAIL;
+
+ eth_hw_addr_set(netdev, sa->sa_data);
+ memset(mask, 0xFF, ETH_ALEN);
+
+ return adin1110_write_mac_address(port_priv, ADIN_MAC_ADDR_SLOT, netdev->dev_addr, mask);
+}
+
+static int adin1110_ioctl(struct net_device *netdev, struct ifreq *rq, int cmd)
+{
+ if (!netif_running(netdev))
+ return -EINVAL;
+
+ if (!netdev->phydev)
+ return -ENODEV;
+
+ return phy_mii_ioctl(netdev->phydev, rq, cmd);
+}
+
+static void adin1110_rx_mode_work(struct work_struct *work)
+{
+ struct adin1110_port_priv *port_priv = container_of(work, struct adin1110_port_priv, rx_mode_work);
+ struct adin1110_priv *priv = port_priv->priv;
+ u32 mask;
+
+ if (!port_priv->nr)
+ mask = ADIN1110_FWD_UNK2HOST;
+ else
+ mask = ADIN2111_P2_FWD_UNK2HOST;
+
+ mutex_lock(&priv->lock);
+
+ /* Bridge core sets IFF_PROMISC on all interfaces and all frames would be
+ * forwarded to the CPU over SPI. Allow this only on the single port MAC.
+ */
+ if (priv->cfg->id == ADIN1110_MAC)
+ adin1110_set_bits(priv, ADIN1110_CONFIG2, mask,
+ (port_priv->flags & IFF_PROMISC) ? mask : 0);
+
+ adin1110_multicast_filter(port_priv, ADIN_MAC_MULTICAST_ADDR_SLOT,
+ !!(port_priv->flags & IFF_ALLMULTI));
+
+ mutex_unlock(&priv->lock);
+}
+
+static void adin1110_set_rx_mode(struct net_device *dev)
+{
+ struct adin1110_port_priv *port_priv = netdev_priv(dev);
+ struct adin1110_priv *priv = port_priv->priv;
+
+ spin_lock(&priv->state_lock);
+
+ port_priv->flags = dev->flags;
+ schedule_work(&port_priv->rx_mode_work);
+
+ spin_unlock(&priv->state_lock);
+}
+
+static int adin1110_init_mac(struct adin1110_port_priv *port_priv)
+{
+ struct net_device *netdev = port_priv->netdev;
+ u8 mask[ETH_ALEN];
+ u8 mac[ETH_ALEN];
+ int ret;
+
+ memset(mask, 0xFF, ETH_ALEN);
+ ret = adin1110_write_mac_address(port_priv, ADIN_MAC_ADDR_SLOT, netdev->dev_addr, mask);
+ if (ret < 0) {
+ netdev_err(netdev, "Could not set MAC address: %pM, %d\n", mac, ret);
+ return ret;
+ }
+
+ memset(mac, 0xFF, ETH_ALEN);
+ ret = adin1110_write_mac_address(port_priv, ADIN_MAC_BROADCAST_ADDR_SLOT, mac, mask);
+ if (ret < 0) {
+ netdev_err(netdev, "Could not set Broadcast MAC address: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int adin1110_net_open(struct net_device *net_dev)
+{
+ struct adin1110_port_priv *port_priv = netdev_priv(net_dev);
+ struct adin1110_priv *priv = port_priv->priv;
+ u32 val;
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ /* Configure MAC to compute and append the FCS itself. */
+ ret = adin1110_set_bits(priv, ADIN1110_CONFIG2, ADIN1110_CRC_APPEND, ADIN1110_CRC_APPEND);
+ if (ret < 0) {
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ val = ADIN1110_TX_RDY_IRQ | ADIN1110_RX_RDY_IRQ | ADIN1110_SPI_ERR_IRQ;
+ if (priv->cfg->id == ADIN2111_MAC)
+ val |= ADIN2111_RX_RDY_IRQ;
+
+ priv->irq_mask = val;
+ ret = adin1110_write_reg(priv, ADIN1110_IMASK1, ~val);
+ if (ret < 0) {
+ netdev_err(net_dev, "Failed to enable chip IRQs: %d\n", ret);
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ ret = adin1110_read_reg(priv, ADIN1110_TX_SPACE, &val);
+ if (ret < 0) {
+ netdev_err(net_dev, "Failed to read TX FIFO space: %d\n", ret);
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ priv->tx_space = 2 * val;
+
+ ret = adin1110_init_mac(port_priv);
+ if (ret < 0) {
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ ret = adin1110_set_bits(priv, ADIN1110_CONFIG1, ADIN1110_CONFIG1_SYNC,
+ ADIN1110_CONFIG1_SYNC);
+ if (ret < 0) {
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ mutex_unlock(&priv->lock);
+
+ phy_start(port_priv->phydev);
+
+ netif_start_queue(net_dev);
+
+ return ret;
+}
+
+static int adin1110_net_stop(struct net_device *net_dev)
+{
+ struct adin1110_port_priv *port_priv = netdev_priv(net_dev);
+
+ netif_stop_queue(port_priv->netdev);
+ flush_work(&port_priv->tx_work);
+ phy_stop(port_priv->phydev);
+
+ return 0;
+}
+
+static void adin1110_tx_work(struct work_struct *work)
+{
+ struct adin1110_port_priv *port_priv = container_of(work, struct adin1110_port_priv, tx_work);
+ struct adin1110_priv *priv = port_priv->priv;
+ struct sk_buff *txb;
+ bool last;
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ last = skb_queue_empty(&port_priv->txq);
+
+ while (!last) {
+ txb = skb_dequeue(&port_priv->txq);
+ last = skb_queue_empty(&port_priv->txq);
+
+ if (txb) {
+ ret = adin1110_write_fifo(port_priv, txb);
+ if (ret < 0)
+ netdev_err(port_priv->netdev, "Frame write error: %d\n", ret);
+
+ dev_kfree_skb(txb);
+ }
+ }
+
+ mutex_unlock(&priv->lock);
+}
+
+static netdev_tx_t adin1110_start_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+ struct adin1110_port_priv *port_priv = netdev_priv(dev);
+ struct adin1110_priv *priv = port_priv->priv;
+ netdev_tx_t netdev_ret = NETDEV_TX_OK;
+ u32 tx_space_needed;
+
+ spin_lock(&priv->state_lock);
+
+ tx_space_needed = skb->len + ADIN1110_FRAME_HEADER_LEN + ADIN1110_INTERNAL_SIZE_HEADER_LEN;
+ if (tx_space_needed > priv->tx_space) {
+ netif_stop_queue(dev);
+ netdev_ret = NETDEV_TX_BUSY;
+ } else {
+ priv->tx_space -= tx_space_needed;
+ skb_queue_tail(&port_priv->txq, skb);
+ }
+
+ spin_unlock(&priv->state_lock);
+
+ schedule_work(&port_priv->tx_work);
+
+ return netdev_ret;
+}
+
+void adin1110_ndo_get_stats64(struct net_device *dev, struct rtnl_link_stats64 *storage)
+{
+ struct adin1110_port_priv *port_priv = netdev_priv(dev);
+ struct adin1110_priv *priv = port_priv->priv;
+ u32 val;
+
+ mutex_lock(&priv->lock);
+
+ adin1110_read_reg(priv, ADIN1110_RX_FRM_CNT(port_priv->nr), &val);
+ storage->rx_packets = val;
+
+ adin1110_read_reg(priv, ADIN1110_TX_FRM_CNT(port_priv->nr), &val);
+ storage->tx_packets = val;
+
+ storage->rx_bytes = port_priv->rx_bytes;
+ storage->tx_bytes = port_priv->tx_bytes;
+
+ adin1110_read_reg(priv, ADIN1110_RX_CRC_ERR_CNT(port_priv->nr), &val);
+ storage->rx_errors += val;
+
+ adin1110_read_reg(priv, ADIN1110_RX_ALGN_ERR_CNT(port_priv->nr), &val);
+ storage->rx_errors += val;
+
+ adin1110_read_reg(priv, ADIN1110_RX_LS_ERR_CNT(port_priv->nr), &val);
+ storage->rx_errors += val;
+
+ adin1110_read_reg(priv, ADIN1110_RX_PHY_ERR_CNT(port_priv->nr), &val);
+ storage->rx_errors += val;
+
+ adin1110_read_reg(priv, ADIN1110_RX_DROP_FULL_CNT(port_priv->nr), &val);
+ storage->rx_dropped = val;
+
+ adin1110_read_reg(priv, ADIN1110_RX_MCAST_CNT(port_priv->nr), &val);
+ storage->multicast = val;
+
+ mutex_unlock(&priv->lock);
+}
+
+static int adin1110_port_get_port_parent_id(struct net_device *dev,
+ struct netdev_phys_item_id *ppid)
+{
+ struct adin1110_port_priv *port_priv = netdev_priv(dev);
+ struct adin1110_priv *priv = port_priv->priv;
+
+ ppid->id_len = strnlen(priv->mii_bus_name, MII_BUS_ID_SIZE);
+ memcpy(ppid->id, priv->mii_bus_name, ppid->id_len);
+
+ return 0;
+}
+
+static int adin1110_ndo_get_phys_port_name(struct net_device *dev, char *name, size_t len)
+{
+ struct adin1110_port_priv *port_priv = netdev_priv(dev);
+ int err;
+
+ err = snprintf(name, len, "p%d", port_priv->nr);
+ if (err >= len)
+ return -EINVAL;
+
+ return 0;
+}
+
+static const struct net_device_ops adin1110_netdev_ops = {
+ .ndo_open = adin1110_net_open,
+ .ndo_stop = adin1110_net_stop,
+ .ndo_do_ioctl = adin1110_ioctl,
+ .ndo_start_xmit = adin1110_start_xmit,
+ .ndo_set_mac_address = adin1110_set_mac_address,
+ .ndo_set_rx_mode = adin1110_set_rx_mode,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_get_stats64 = adin1110_ndo_get_stats64,
+ .ndo_get_port_parent_id = adin1110_port_get_port_parent_id,
+ .ndo_get_phys_port_name = adin1110_ndo_get_phys_port_name,
+};
+
+static void adin1110_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *di)
+{
+ strscpy(di->driver, "ADIN1110", sizeof(di->driver));
+ strscpy(di->version, "1.00", sizeof(di->version));
+ strscpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info));
+}
+
+static const struct ethtool_ops adin1110_ethtool_ops = {
+ .get_drvinfo = adin1110_get_drvinfo,
+ .get_link = ethtool_op_get_link,
+ .get_link_ksettings = phy_ethtool_get_link_ksettings,
+ .set_link_ksettings = phy_ethtool_set_link_ksettings,
+};
+
+static void adin1110_adjust_link(struct net_device *dev)
+{
+ struct phy_device *phydev = dev->phydev;
+
+ if (!phydev->link)
+ phy_print_status(phydev);
+}
+
+/* PHY ID is stored in the MAC registers too, check spi connection by reading it */
+static int adin1110_check_spi(struct adin1110_priv *priv)
+{
+ int ret;
+ u32 val;
+
+ ret = adin1110_read_reg(priv, ADIN1110_PHY_ID, &val);
+ if (ret < 0)
+ return ret;
+
+ if (val != priv->cfg->phy_id_val) {
+ dev_err(&priv->spidev->dev, "PHY ID read: %x\n", val);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static void adin1110_disconnect_phy(void *data)
+{
+ phy_disconnect(data);
+}
+
+static void adin1110_unregister_notifier(void *data)
+{
+ unregister_netdevice_notifier(data);
+}
+
+static int adin1110_hw_forwarding(struct adin1110_priv *priv, bool enable)
+{
+ int mac_nr;
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ /* Configure MAC to forward unknown host to other port. */
+ ret = adin1110_set_bits(priv, ADIN1110_CONFIG2, ADIN2111_FWD_UNK2PORT,
+ enable ? ADIN2111_FWD_UNK2PORT : 0);
+ if (ret < 0) {
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ /* Broadcast and multicast should also be forwarded to the other port */
+ for (mac_nr = 0; mac_nr <= ADIN_MAC_BROADCAST_ADDR_SLOT; mac_nr++) {
+ u32 offset = mac_nr * 2;
+ u32 port_rules;
+ u32 port_rules_mask;
+ u32 val;
+
+ if (mac_nr == ADIN_MAC_ADDR_SLOT)
+ continue;
+
+ port_rules_mask = ADIN1110_MAC_ADDR_APPLY2PORT | ADIN2111_MAC_ADDR_APPLY2PORT2;
+ port_rules = port_rules_mask;
+ port_rules_mask |= ADIN2111_MAC_ADDR_TO_OTHER_PORT;
+ if (enable)
+ port_rules |= ADIN2111_MAC_ADDR_TO_OTHER_PORT;
+
+ /* tell MAC to forward this DA to host */
+ val = port_rules | ADIN1110_MAC_ADDR_TO_HOST;
+ ret = adin1110_set_bits(priv, ADIN1110_MAC_ADDR_FILTER_UPR + offset,
+ port_rules_mask, port_rules);
+ if (ret < 0) {
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+ }
+
+ ret = adin1110_set_bits(priv, ADIN1110_CONFIG2, ADIN2111_FWD_UNK2PORT,
+ ADIN2111_FWD_UNK2PORT);
+ if (ret < 0) {
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ ret = adin1110_set_bits(priv, ADIN1110_CONFIG1, ADIN1110_CONFIG1_SYNC,
+ ADIN1110_CONFIG1_SYNC);
+
+ mutex_unlock(&priv->lock);
+
+ if (ret < 0)
+ return ret;
+
+ priv->forwarding = enable;
+
+ return ret;
+}
+
+static int adin1110_port_bridge_join(struct adin1110_port_priv *port_priv,
+ struct net_device *bridge)
+{
+ struct adin1110_priv *priv = port_priv->priv;
+ int ret = 0;
+
+ /* Having the same port belong to multiple bridges is not supported */
+ if (port_priv->bridge && port_priv->bridge != bridge)
+ return -EOPNOTSUPP;
+
+ port_priv->bridge = bridge;
+
+ /* If other port joined same bridge, allow forwarding between ports */
+ if (priv->ports[0]->bridge == priv->ports[1]->bridge)
+ ret = adin1110_hw_forwarding(priv, true);
+
+ return ret;
+}
+
+static int adin1110_port_bridge_leave(struct adin1110_port_priv *port_priv,
+ struct net_device *bridge)
+{
+ struct adin1110_priv *priv = port_priv->priv;
+ int ret = 0;
+
+ if (priv->ports[0]->bridge == priv->ports[1]->bridge)
+ ret = adin1110_hw_forwarding(priv, false);
+
+ port_priv->bridge = NULL;
+
+ return ret;
+}
+
+static int adin1110_netdevice_event(struct notifier_block *unused, unsigned long event, void *ptr)
+{
+ struct net_device *dev = netdev_notifier_info_to_dev(ptr);
+ struct adin1110_port_priv *port_priv = netdev_priv(dev);
+ struct netdev_notifier_changeupper_info *info = ptr;
+ int ret = 0;
+
+ switch (event) {
+ case NETDEV_CHANGEUPPER:
+ if (netif_is_bridge_master(info->upper_dev)) {
+ if (info->linking)
+ ret = adin1110_port_bridge_join(port_priv, info->upper_dev);
+ else
+ ret = adin1110_port_bridge_leave(port_priv, info->upper_dev);
+ }
+ break;
+ default:
+ break;
+ }
+
+ return notifier_from_errno(ret);
+}
+
+struct notifier_block adin1110_netdevice_nb __read_mostly = {
+ .notifier_call = adin1110_netdevice_event,
+};
+
+static int adin1110_probe_netdevs(struct adin1110_priv *priv)
+{
+ struct device *dev = &priv->spidev->dev;
+ struct adin1110_port_priv *port_priv;
+ struct net_device *netdev;
+ int ret;
+ int i;
+
+ for (i = 0; i < priv->cfg->ports_nr; i++) {
+ netdev = devm_alloc_etherdev(dev, sizeof(*port_priv));
+ if (!netdev)
+ return -ENOMEM;
+
+ port_priv = netdev_priv(netdev);
+ port_priv->netdev = netdev;
+ port_priv->priv = priv;
+ port_priv->cfg = priv->cfg;
+ port_priv->nr = i;
+ priv->ports[i] = port_priv;
+ SET_NETDEV_DEV(netdev, dev);
+
+ ret = device_get_ethdev_address(dev, netdev);
+ if (ret < 0)
+ return ret;
+
+ netdev->irq = priv->spidev->irq;
+ INIT_WORK(&port_priv->tx_work, adin1110_tx_work);
+ INIT_WORK(&port_priv->rx_mode_work, adin1110_rx_mode_work);
+ skb_queue_head_init(&port_priv->txq);
+
+ netif_carrier_off(netdev);
+
+ netdev->if_port = IF_PORT_10BASET;
+ netdev->netdev_ops = &adin1110_netdev_ops;
+ netdev->ethtool_ops = &adin1110_ethtool_ops;
+ netdev->priv_flags |= IFF_UNICAST_FLT;
+ netdev->features |= NETIF_F_NETNS_LOCAL;
+
+ ret = devm_register_netdev(dev, netdev);
+ if (ret < 0) {
+ dev_err(dev, "failed to register network device\n");
+ return ret;
+ }
+
+ port_priv->phydev = get_phy_device(priv->mii_bus, i + 1, false);
+ if (!port_priv->phydev) {
+ netdev_err(netdev, "Could not find PHY with device address: %d.\n", i);
+ return -ENODEV;
+ }
+
+ port_priv->phydev = phy_connect(netdev, phydev_name(port_priv->phydev),
+ adin1110_adjust_link, PHY_INTERFACE_MODE_MII);
+ if (IS_ERR(port_priv->phydev)) {
+ netdev_err(netdev, "Could not connect PHY with device address: %d.\n", i);
+ return PTR_ERR(port_priv->phydev);
+ }
+
+ ret = devm_add_action_or_reset(dev, adin1110_disconnect_phy, port_priv->phydev);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* ADIN1110 INT_N pin will be used to signal the host */
+ ret = devm_request_threaded_irq(dev, priv->spidev->irq, NULL, adin1110_irq,
+ IRQF_TRIGGER_LOW | IRQF_ONESHOT, dev_name(dev), priv);
+ if (ret < 0)
+ return ret;
+
+ if (priv->cfg->id == ADIN2111_MAC) {
+ ret = register_netdevice_notifier(&adin1110_netdevice_nb);
+ if (ret < 0)
+ return ret;
+
+ ret = devm_add_action_or_reset(dev, adin1110_unregister_notifier,
+ &adin1110_netdevice_nb);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int adin1110_probe(struct spi_device *spi)
+{
+ const struct spi_device_id *dev_id = spi_get_device_id(spi);
+ struct device *dev = &spi->dev;
+ struct adin1110_priv *priv;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(struct adin1110_priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->spidev = spi;
+ priv->cfg = &adin1110_cfgs[dev_id->driver_data];
+ spi->bits_per_word = 8;
+
+ mutex_init(&priv->lock);
+ spin_lock_init(&priv->state_lock);
+
+ /* use of CRC on control and data transactions is pin dependent */
+ priv->append_crc = device_property_read_bool(dev, "adi,spi-crc");
+ if (priv->append_crc)
+ crc8_populate_msb(adin1110_crc_table, 0x7);
+
+ ret = adin1110_check_spi(priv);
+ if (ret < 0) {
+ dev_err(dev, "SPI read failed: %d\n", ret);
+ return ret;
+ }
+
+ ret = adin1110_write_reg(priv, ADIN1110_RESET, ADIN1110_SWRESET);
+ if (ret < 0)
+ return ret;
+
+ ret = adin1110_register_mdiobus(priv, dev);
+ if (ret < 0) {
+ dev_err(dev, "Could not register MDIO bus %d\n", ret);
+ return ret;
+ }
+
+ return adin1110_probe_netdevs(priv);
+}
+
+static const struct of_device_id adin1110_match_table[] = {
+ { .compatible = "adi,adin1110" },
+ { .compatible = "adi,adin2111" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, adin1110_match_table);
+
+static const struct spi_device_id adin1110_spi_id[] = {
+ { .name = "adin1110", .driver_data = ADIN1110_MAC },
+ { .name = "adin2111", .driver_data = ADIN2111_MAC },
+ { }
+};
+
+static struct spi_driver adin1110_driver = {
+ .driver = {
+ .name = "adin1110",
+ .of_match_table = adin1110_match_table,
+ },
+ .probe = adin1110_probe,
+ .id_table = adin1110_spi_id,
+};
+module_spi_driver(adin1110_driver);
+
+MODULE_DESCRIPTION("ADIN1110 Network driver");
+MODULE_AUTHOR("Alexandru Tachici <[email protected]>");
+MODULE_LICENSE("Dual BSD/GPL");
--
2.25.1
On Fri, 24 Jun 2022 23:06:27 +0300 [email protected] wrote:
> From: Alexandru Tachici <[email protected]>
>
> The ADIN1110 is a low power single port 10BASE-T1L MAC-PHY
> designed for industrial Ethernet applications. It integrates
> an Ethernet PHY core with a MAC and all the associated analog
> circuitry, input and output clock buffering.
Please fix the warnings when built with W=1 C=1.
> +static int adin1110_mdio_read(struct mii_bus *bus, int phy_id, int reg)
> +{
> + struct adin1110_priv *priv = bus->priv;
> + u32 val = 0;
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + val |= FIELD_PREP(ADIN1110_MDIO_OP, ADIN1110_MDIO_OP_RD);
> + val |= FIELD_PREP(ADIN1110_MDIO_ST, 0x1);
> + val |= FIELD_PREP(ADIN1110_MDIO_PRTAD, phy_id);
> + val |= FIELD_PREP(ADIN1110_MDIO_DEVAD, reg);
> +
> + /* write the clause 22 read command to the chip */
Please return -EOPNOTSUPP if asked to do a C45 transfer.
> +static int adin1110_mdio_write(struct mii_bus *bus, int phy_id, int reg, u16 reg_val)
> +{
> + struct adin1110_priv *priv = bus->priv;
> + u32 val = 0;
> + int ret;
same here.
Andrew
> +static void adin1110_read_frames(struct adin1110_port_priv *port_priv)
> +{
> + struct adin1110_priv *priv = port_priv->priv;
> + u32 status1;
> + int ret;
> +
> + while (1) {
> + ret = adin1110_read_reg(priv, ADIN1110_STATUS1, &status1);
> + if (ret < 0)
> + return;
> +
> + if (!adin1110_port_rx_ready(port_priv, status1))
> + break;
> +
> + ret = adin1110_read_fifo(port_priv);
> + if (ret < 0)
> + return;
> + }
Not sure an endless loop is a good idea here. I assume your SPI bus is
slower than your two Ethernet interfaces. So somebody could DOS the
machine by sending ethernet at line rate, and this function would
never exit? NAPI has the concept of a budget. You only every receive
up to 64 frames at once.
> +static int adin1110_set_mac_address(struct net_device *netdev, void *addr)
> +{
> + struct adin1110_port_priv *port_priv = netdev_priv(netdev);
> + struct sockaddr *sa = addr;
> + u8 mask[ETH_ALEN];
> +
> + if (netif_running(netdev))
> + return -EBUSY;
> +
> + if (!is_valid_ether_addr(sa->sa_data))
> + return -EADDRNOTAVAIL;
> +
> + eth_hw_addr_set(netdev, sa->sa_data);
> + memset(mask, 0xFF, ETH_ALEN);
> +
> + return adin1110_write_mac_address(port_priv, ADIN_MAC_ADDR_SLOT, netdev->dev_addr, mask);
> +}
So there is a function to set an entry for Multicast, another for its
own MAC address? Does it need entries for broadcast? What about STP
bridge PDUs?
> +static void adin1110_rx_mode_work(struct work_struct *work)
> +{
> + struct adin1110_port_priv *port_priv = container_of(work, struct adin1110_port_priv, rx_mode_work);
> + struct adin1110_priv *priv = port_priv->priv;
> + u32 mask;
> +
> + if (!port_priv->nr)
> + mask = ADIN1110_FWD_UNK2HOST;
> + else
> + mask = ADIN2111_P2_FWD_UNK2HOST;
> +
> + mutex_lock(&priv->lock);
> +
> + /* Bridge core sets IFF_PROMISC on all interfaces and all frames would be
> + * forwarded to the CPU over SPI. Allow this only on the single port MAC.
> + */
That is a bit of an over-simplification. But it is not clear to me yet
if this hardware can do it all correct, so this is a good start.
> +static int adin1110_init_mac(struct adin1110_port_priv *port_priv)
> +{
> + struct net_device *netdev = port_priv->netdev;
> + u8 mask[ETH_ALEN];
> + u8 mac[ETH_ALEN];
> + int ret;
> +
> + memset(mask, 0xFF, ETH_ALEN);
> + ret = adin1110_write_mac_address(port_priv, ADIN_MAC_ADDR_SLOT, netdev->dev_addr, mask);
> + if (ret < 0) {
> + netdev_err(netdev, "Could not set MAC address: %pM, %d\n", mac, ret);
> + return ret;
> + }
Better to call adin1110_set_mac_address()
> +
> + memset(mac, 0xFF, ETH_ALEN);
> + ret = adin1110_write_mac_address(port_priv, ADIN_MAC_BROADCAST_ADDR_SLOT, mac, mask);
> + if (ret < 0) {
> + netdev_err(netdev, "Could not set Broadcast MAC address: %d\n", ret);
> + return ret;
> + }
And i would suggest a little helper for this as well.
This partially answers my question above. But so far, i see no STP
support?
> +static int adin1110_net_open(struct net_device *net_dev)
> +{
> + struct adin1110_port_priv *port_priv = netdev_priv(net_dev);
> + struct adin1110_priv *priv = port_priv->priv;
> + u32 val;
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + /* Configure MAC to compute and append the FCS itself. */
> + ret = adin1110_set_bits(priv, ADIN1110_CONFIG2, ADIN1110_CRC_APPEND, ADIN1110_CRC_APPEND);
> + if (ret < 0) {
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
> +
> + val = ADIN1110_TX_RDY_IRQ | ADIN1110_RX_RDY_IRQ | ADIN1110_SPI_ERR_IRQ;
> + if (priv->cfg->id == ADIN2111_MAC)
> + val |= ADIN2111_RX_RDY_IRQ;
> +
> + priv->irq_mask = val;
> + ret = adin1110_write_reg(priv, ADIN1110_IMASK1, ~val);
> + if (ret < 0) {
> + netdev_err(net_dev, "Failed to enable chip IRQs: %d\n", ret);
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
Rather than have all these
mutex_unlock(&priv->lock);
+ return ret;
it is better to have
goto out;
out:
mutex_unlock(&priv->lock);
return ret;
You are less likely to miss an unlock. Please do this everywhere.
> +void adin1110_ndo_get_stats64(struct net_device *dev, struct rtnl_link_stats64 *storage)
> +{
> + struct adin1110_port_priv *port_priv = netdev_priv(dev);
> + struct adin1110_priv *priv = port_priv->priv;
> + u32 val;
> +
> + mutex_lock(&priv->lock);
I really should remember this, since it keeps coming up again and
again. I think this gets called in a context which does not allow
blocking.
> +static void adin1110_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *di)
> +{
> + strscpy(di->driver, "ADIN1110", sizeof(di->driver));
> + strscpy(di->version, "1.00", sizeof(di->version));
No version information please, it is meaningless. The core will fill
in the kernel version, which at least is a little bit useful.
> +static int adin1110_hw_forwarding(struct adin1110_priv *priv, bool enable)
> +{
> + int mac_nr;
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + /* Configure MAC to forward unknown host to other port. */
Does unknown also go to the CPU? You need the software bridge to see
such frames, it might know where they go, e.g. over a VPN, out some
other Ethernet interface etc.
> + ret = adin1110_set_bits(priv, ADIN1110_CONFIG2, ADIN2111_FWD_UNK2PORT,
> + enable ? ADIN2111_FWD_UNK2PORT : 0);
> + if (ret < 0) {
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
> +
> + /* Broadcast and multicast should also be forwarded to the other port */
So it seems like there is no STP support. If your network has loops,
it will die in a broadcast storm. Is STP something you plan to add
later?
> +static int adin1110_port_bridge_join(struct adin1110_port_priv *port_priv,
> + struct net_device *bridge)
> +{
> + struct adin1110_priv *priv = port_priv->priv;
> + int ret = 0;
> +
> + /* Having the same port belong to multiple bridges is not supported */
> + if (port_priv->bridge && port_priv->bridge != bridge)
> + return -EOPNOTSUPP;
That is always true, so i don't think you need to check this. If this
happens, something is broken in the core.
> +
> + port_priv->bridge = bridge;
> +
> + /* If other port joined same bridge, allow forwarding between ports */
> + if (priv->ports[0]->bridge == priv->ports[1]->bridge)
> + ret = adin1110_hw_forwarding(priv, true);
> +
> + return ret;
> +}
> +
> +static int adin1110_probe_netdevs(struct adin1110_priv *priv)
> +{
> + struct device *dev = &priv->spidev->dev;
> + struct adin1110_port_priv *port_priv;
> + struct net_device *netdev;
> + int ret;
> + int i;
> +
> + for (i = 0; i < priv->cfg->ports_nr; i++) {
> + netdev = devm_alloc_etherdev(dev, sizeof(*port_priv));
> + if (!netdev)
> + return -ENOMEM;
> +
> + port_priv = netdev_priv(netdev);
> + port_priv->netdev = netdev;
> + port_priv->priv = priv;
> + port_priv->cfg = priv->cfg;
> + port_priv->nr = i;
> + priv->ports[i] = port_priv;
> + SET_NETDEV_DEV(netdev, dev);
> +
> + ret = device_get_ethdev_address(dev, netdev);
> + if (ret < 0)
> + return ret;
> +
> + netdev->irq = priv->spidev->irq;
> + INIT_WORK(&port_priv->tx_work, adin1110_tx_work);
> + INIT_WORK(&port_priv->rx_mode_work, adin1110_rx_mode_work);
> + skb_queue_head_init(&port_priv->txq);
> +
> + netif_carrier_off(netdev);
> +
> + netdev->if_port = IF_PORT_10BASET;
> + netdev->netdev_ops = &adin1110_netdev_ops;
> + netdev->ethtool_ops = &adin1110_ethtool_ops;
> + netdev->priv_flags |= IFF_UNICAST_FLT;
> + netdev->features |= NETIF_F_NETNS_LOCAL;
> +
> + ret = devm_register_netdev(dev, netdev);
> + if (ret < 0) {
> + dev_err(dev, "failed to register network device\n");
> + return ret;
> + }
> +
> + port_priv->phydev = get_phy_device(priv->mii_bus, i + 1, false);
> + if (!port_priv->phydev) {
> + netdev_err(netdev, "Could not find PHY with device address: %d.\n", i);
> + return -ENODEV;
> + }
> +
> + port_priv->phydev = phy_connect(netdev, phydev_name(port_priv->phydev),
> + adin1110_adjust_link, PHY_INTERFACE_MODE_MII);
That should probably be PHY_INTERFACE_MODE_INTERNAL.
Andrew
Hi Alexandru,
Am 24.06.22 um 22:06 schrieb [email protected]:
> From: Alexandru Tachici <[email protected]>
>
> The ADIN1110 is a low power single port 10BASE-T1L MAC-PHY
> designed for industrial Ethernet applications. It integrates
> an Ethernet PHY core with a MAC and all the associated analog
> circuitry, input and output clock buffering.
>
> ADIN1110 MAC-PHY encapsulates the ADIN1100 PHY. The PHY registers
> can be accessed through the MDIO MAC registers.
> We are registering an MDIO bus with custom read/write in order
> to let the PHY to be discovered by the PAL. This will let
> the ADIN1100 Linux driver to probe and take control of
> the PHY.
>
> The ADIN2111 is a low power, low complexity, two-Ethernet ports
> switch with integrated 10BASE-T1L PHYs and one serial peripheral
> interface (SPI) port.
>
> The device is designed for industrial Ethernet applications using
> low power constrained nodes and is compliant with the IEEE 802.3cg-2019
> Ethernet standard for long reach 10 Mbps single pair Ethernet (SPE).
> The switch supports various routing configurations between
> the two Ethernet ports and the SPI host port providing a flexible
> solution for line, daisy-chain, or ring network topologies.
>
> The ADIN2111 supports cable reach of up to 1700 meters with ultra
> low power consumption of 77 mW. The two PHY cores support the
> 1.0 V p-p operating mode and the 2.4 V p-p operating mode defined
> in the IEEE 802.3cg standard.
>
> The device integrates the switch, two Ethernet physical layer (PHY)
> cores with a media access control (MAC) interface and all the
> associated analog circuitry, and input and output clock buffering.
>
> The device also includes internal buffer queues, the SPI and
> subsystem registers, as well as the control logic to manage the reset
> and clock control and hardware pin configuration.
>
> Access to the PHYs is exposed via an internal MDIO bus. Writes/reads
> can be performed by reading/writing to the ADIN2111 MDIO registers
> via SPI.
>
> On probe, for each port, a struct net_device is allocated and
> registered. When both ports are added to the same bridge, the driver
> will enable offloading of frame forwarding at the hardware level.
>
> Co-developed-by: Lennart Franzen <[email protected]>
> Signed-off-by: Lennart Franzen <[email protected]>
> Signed-off-by: Alexandru Tachici <[email protected]>
> ---
> drivers/net/ethernet/Kconfig | 1 +
> drivers/net/ethernet/Makefile | 1 +
> drivers/net/ethernet/adi/Kconfig | 28 +
> drivers/net/ethernet/adi/Makefile | 6 +
> drivers/net/ethernet/adi/adin1110.c | 1312 +++++++++++++++++++++++++++
> 5 files changed, 1348 insertions(+)
> create mode 100644 drivers/net/ethernet/adi/Kconfig
> create mode 100644 drivers/net/ethernet/adi/Makefile
> create mode 100644 drivers/net/ethernet/adi/adin1110.c
>
> diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
> index 955abbc5490e..954cd8c96032 100644
> --- a/drivers/net/ethernet/Kconfig
> +++ b/drivers/net/ethernet/Kconfig
> @@ -120,6 +120,7 @@ config LANTIQ_XRX200
> Support for the PMAC of the Gigabit switch (GSWIP) inside the
> Lantiq / Intel VRX200 VDSL SoC
>
> +source "drivers/net/ethernet/adi/Kconfig"
> source "drivers/net/ethernet/litex/Kconfig"
> source "drivers/net/ethernet/marvell/Kconfig"
> source "drivers/net/ethernet/mediatek/Kconfig"
> diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
> index 9eb01169957f..bc65ca0d9b4c 100644
> --- a/drivers/net/ethernet/Makefile
> +++ b/drivers/net/ethernet/Makefile
> @@ -8,6 +8,7 @@ obj-$(CONFIG_NET_VENDOR_8390) += 8390/
> obj-$(CONFIG_NET_VENDOR_ACTIONS) += actions/
> obj-$(CONFIG_NET_VENDOR_ADAPTEC) += adaptec/
> obj-$(CONFIG_GRETH) += aeroflex/
> +obj-$(CONFIG_NET_VENDOR_ADI) += adi/
> obj-$(CONFIG_NET_VENDOR_AGERE) += agere/
> obj-$(CONFIG_NET_VENDOR_ALACRITECH) += alacritech/
> obj-$(CONFIG_NET_VENDOR_ALLWINNER) += allwinner/
> diff --git a/drivers/net/ethernet/adi/Kconfig b/drivers/net/ethernet/adi/Kconfig
> new file mode 100644
> index 000000000000..da3bdd302502
> --- /dev/null
> +++ b/drivers/net/ethernet/adi/Kconfig
> @@ -0,0 +1,28 @@
> +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
> +#
> +# Analog Devices device configuration
> +#
> +
> +config NET_VENDOR_ADI
> + bool "Analog Devices devices"
> + default y
> + depends on SPI
> + help
> + If you have a network (Ethernet) card belonging to this class, say Y.
> +
> + Note that the answer to this question doesn't directly affect the
> + kernel: saying N will just cause the configurator to skip all
> + the questions about ADI devices. If you say Y, you will be asked
> + for your specific card in the following questions.
> +
> +if NET_VENDOR_ADI
> +
> +config ADIN1110
> + tristate "Analog Devices ADIN1110 MAC-PHY"
> + depends on SPI && NET_SWITCHDEV
> + select CRC8
> + help
> + Say yes here to build support for Analog Devices ADIN1110
> + Low Power 10BASE-T1L Ethernet MAC-PHY.
> +
> +endif # NET_VENDOR_ADI
> diff --git a/drivers/net/ethernet/adi/Makefile b/drivers/net/ethernet/adi/Makefile
> new file mode 100644
> index 000000000000..d0383d94303c
> --- /dev/null
> +++ b/drivers/net/ethernet/adi/Makefile
> @@ -0,0 +1,6 @@
> +# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
> +#
> +# Makefile for the Analog Devices network device drivers.
> +#
> +
> +obj-$(CONFIG_ADIN1110) += adin1110.o
> diff --git a/drivers/net/ethernet/adi/adin1110.c b/drivers/net/ethernet/adi/adin1110.c
> new file mode 100644
> index 000000000000..fdefd6fdeb9d
> --- /dev/null
> +++ b/drivers/net/ethernet/adi/adin1110.c
> @@ -0,0 +1,1312 @@
> +// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
> +/* ADIN1110 Low Power 10BASE-T1L Ethernet MAC-PHY
> + * ADIN2111 2-Port Ethernet Switch with Integrated 10BASE-T1L PHY
> + *
> + * Copyright 2021 Analog Devices Inc.
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/bits.h>
> +#include <linux/cache.h>
> +#include <linux/crc8.h>
> +#include <linux/etherdevice.h>
> +#include <linux/ethtool.h>
> +#include <linux/interrupt.h>
> +#include <linux/iopoll.h>
> +#include <linux/gpio.h>
> +#include <linux/kernel.h>
> +#include <linux/mii.h>
> +#include <linux/module.h>
> +#include <linux/netdevice.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/phy.h>
> +#include <linux/property.h>
> +#include <linux/spi/spi.h>
> +
> +#include <asm/unaligned.h>
> +
> +#define ADIN1110_PHY_ID 0x1
> +
> +#define ADIN1110_RESET 0x03
> +#define ADIN1110_SWRESET BIT(0)
> +
> +#define ADIN1110_CONFIG1 0x04
> +#define ADIN1110_CONFIG1_SYNC BIT(15)
> +
> +#define ADIN1110_CONFIG2 0x06
> +#define ADIN2111_FWD_UNK2PORT GENMASK(14, 13)
> +#define ADIN2111_P2_FWD_UNK2HOST BIT(12)
> +#define ADIN1110_CRC_APPEND BIT(5)
> +#define ADIN1110_FWD_UNK2HOST BIT(2)
> +
> +#define ADIN1110_STATUS0 0x08
> +
> +#define ADIN1110_STATUS1 0x09
> +#define ADIN2111_P2_RX_RDY BIT(17)
> +#define ADIN1110_SPI_ERR BIT(10)
> +#define ADIN1110_RX_RDY BIT(4)
> +#define ADIN1110_TX_RDY BIT(3)
> +
> +#define ADIN1110_IMASK1 0x0D
> +#define ADIN2111_RX_RDY_IRQ BIT(17)
> +#define ADIN1110_SPI_ERR_IRQ BIT(10)
> +#define ADIN1110_RX_RDY_IRQ BIT(4)
> +#define ADIN1110_TX_RDY_IRQ BIT(3)
> +
> +#define ADIN1110_MDIOACC 0x20
> +#define ADIN1110_MDIO_TRDONE BIT(31)
> +#define ADIN1110_MDIO_TAERR BIT(30)
> +#define ADIN1110_MDIO_ST GENMASK(29, 28)
> +#define ADIN1110_MDIO_OP GENMASK(27, 26)
> +#define ADIN1110_MDIO_PRTAD GENMASK(25, 21)
> +#define ADIN1110_MDIO_DEVAD GENMASK(20, 16)
> +#define ADIN1110_MDIO_DATA GENMASK(15, 0)
> +
> +#define ADIN1110_TX_FSIZE 0x30
> +#define ADIN1110_TX 0x31
> +#define ADIN1110_TX_SPACE 0x32
> +#define ADIN1110_RX_THRESH 0x33
> +#define ADIN1110_TX_THRESH 0x34
> +
> +#define ADIN1110_FIFO_CLR 0x36
> +#define ADIN1110_FIFO_SIZE 0x3E
> +#define ADIN1110_TFC 0x3F
> +
> +#define ADIN1110_MAC_ADDR_FILTER_UPR 0x50
> +#define ADIN2111_MAC_ADDR_APPLY2PORT2 BIT(31)
> +#define ADIN1110_MAC_ADDR_APPLY2PORT BIT(30)
> +#define ADIN1110_MAC_ADDR_HOST_PRI BIT(19)
> +#define ADIN2111_MAC_ADDR_TO_OTHER_PORT BIT(17)
> +#define ADIN1110_MAC_ADDR_TO_HOST BIT(16)
> +#define ADIN1110_MAC_ADDR GENMASK(15, 0)
> +
> +#define ADIN1110_MAC_ADDR_FILTER_LWR 0x51
> +
> +#define ADIN1110_MAC_ADDR_MASK_UPR 0x70
> +#define ADIN1110_MAC_ADDR_MASK_LWR 0x71
> +
> +#define ADIN1110_RX_FSIZE 0x90
> +#define ADIN1110_RX 0x91
> +
> +#define ADIN1110_RX_FRM_CNT(x) (0xA0 + ((x) * 0x30))
> +#define ADIN1110_RX_MCAST_CNT(x) (0xA2 + ((x) * 0x30))
> +#define ADIN1110_RX_CRC_ERR_CNT(x) (0xA4 + ((x) * 0x30))
> +#define ADIN1110_RX_ALGN_ERR_CNT(x) (0xA5 + ((x) * 0x30))
> +#define ADIN1110_RX_LS_ERR_CNT(x) (0xA6 + ((x) * 0x30))
> +#define ADIN1110_RX_PHY_ERR_CNT(x) (0xA7 + ((x) * 0x30))
> +#define ADIN1110_RX_DROP_FULL_CNT(x) (0xAC + ((x) * 0x30))
> +
> +#define ADIN1110_TX_FRM_CNT(x) (0xA8 + ((x) * 0x30))
> +#define ADIN1110_TX_MCAST_CNT(x) (0xAA + ((x) * 0x30))
> +
> +#define ADIN2111_RX_P2_FSIZE 0xC0
> +#define ADIN2111_RX_P2 0xC1
> +
> +#define ADIN1110_CLEAR_STATUS0 0xFFF
> +#define ADIN1110_CLEAR_STATUS1 U32_MAX
> +
> +/* MDIO_OP codes */
> +#define ADIN1110_MDIO_OP_WR 0x1
> +#define ADIN1110_MDIO_OP_RD 0x3
> +
> +#define ADIN1110_CD BIT(7)
> +#define ADIN1110_WRITE BIT(5)
> +
> +#define ADIN1110_MAX_BUFF 2048
> +#define ADIN1110_WR_HEADER_LEN 2
> +#define ADIN1110_FRAME_HEADER_LEN 2
> +#define ADIN1110_INTERNAL_SIZE_HEADER_LEN 2
> +#define ADIN1110_RD_HEADER_LEN 3
> +#define ADIN1110_REG_LEN 4
> +#define ADIN1110_FEC_LEN 4
> +
> +#define ADIN1110_PHY_ID_VAL 0x0283BC91
> +#define ADIN2111_PHY_ID_VAL 0x0283BCA1
> +
> +#define ADIN1110_TX_SPACE_MAX 0x0FFF
> +
> +#define ADIN_MAC_MAX_PORTS 2
> +
> +#define ADIN_MAC_MULTICAST_ADDR_SLOT 0
> +#define ADIN_MAC_ADDR_SLOT 1
> +#define ADIN_MAC_BROADCAST_ADDR_SLOT 2
> +
> +DECLARE_CRC8_TABLE(adin1110_crc_table);
> +
> +enum adin1110_chips_id {
> + ADIN1110_MAC = 0,
> + ADIN2111_MAC,
> +};
> +
> +struct adin1110_cfg {
> + enum adin1110_chips_id id;
> + char name[MDIO_NAME_SIZE];
> + u32 phy_ids[PHY_MAX_ADDR];
> + u32 ports_nr;
> + u32 phy_id_val;
> +};
> +
> +struct adin1110_port_priv {
> + struct adin1110_priv *priv;
> + struct net_device *netdev;
> + struct net_device *bridge;
> + struct phy_device *phydev;
> + struct work_struct tx_work;
> + u64 rx_bytes;
> + u64 tx_bytes;
> + struct work_struct rx_mode_work;
> + u32 flags;
> + struct sk_buff_head txq;
> + u32 nr;
> + struct adin1110_cfg *cfg;
> +};
> +
> +struct adin1110_priv {
> + struct mutex lock; /* protect spi */
> + spinlock_t state_lock; /* protect RX mode */
> + bool forwarding;
> + struct mii_bus *mii_bus;
> + struct spi_device *spidev;
> + bool append_crc;
> + struct adin1110_cfg *cfg;
> + u32 tx_space;
> + u32 irq_mask;
> + int irq;
> + struct adin1110_port_priv *ports[ADIN_MAC_MAX_PORTS];
> + char mii_bus_name[MII_BUS_ID_SIZE];
> + u8 data[ADIN1110_MAX_BUFF] ____cacheline_aligned;
> +};
> +
> +struct adin1110_cfg adin1110_cfgs[] = {
> + {
> + .id = ADIN1110_MAC,
> + .name = "adin1110",
> + .phy_ids = {1},
> + .ports_nr = 1,
> + .phy_id_val = ADIN1110_PHY_ID_VAL,
> + },
> + {
> + .id = ADIN2111_MAC,
> + .name = "adin2111",
> + .phy_ids = {1, 2},
> + .ports_nr = 2,
> + .phy_id_val = ADIN2111_PHY_ID_VAL,
> + },
> +};
> +
> +static u8 adin1110_crc_data(u8 *data, u32 len)
> +{
> + return crc8(adin1110_crc_table, data, len, 0);
> +}
> +
> +static int adin1110_read_reg(struct adin1110_priv *priv, u16 reg, u32 *val)
> +{
> + struct spi_transfer t[2] = {0};
> + __le16 __reg = cpu_to_le16(reg);
> + u32 header_len = ADIN1110_RD_HEADER_LEN;
> + u32 read_len = ADIN1110_REG_LEN;
> + int ret;
> +
> + priv->data[0] = ADIN1110_CD | FIELD_GET(GENMASK(12, 8), __reg);
> + priv->data[1] = FIELD_GET(GENMASK(7, 0), __reg);
> + priv->data[2] = 0x00;
> +
> + if (priv->append_crc) {
> + priv->data[2] = adin1110_crc_data(&priv->data[0], 2);
> + priv->data[3] = 0x00;
> + header_len++;
> + }
> +
> + t[0].tx_buf = &priv->data[0];
> + t[0].len = header_len;
> +
> + if (priv->append_crc)
> + read_len++;
> +
> + memset(&priv->data[header_len], 0, read_len);
> + t[1].rx_buf = &priv->data[header_len];
> + t[1].len = read_len;
> +
> + ret = spi_sync_transfer(priv->spidev, t, 2);
> + if (ret)
> + return ret;
> +
> + if (priv->append_crc) {
> + u8 recv_crc;
> + u8 crc;
> +
> + crc = adin1110_crc_data(&priv->data[header_len], ADIN1110_REG_LEN);
> + recv_crc = priv->data[header_len + ADIN1110_REG_LEN];
> +
> + if (crc != recv_crc) {
> + dev_err(&priv->spidev->dev, "CRC error.");
This could flood the kernel log very fast. You should try to avoid this
at least with a rate limited version of dev_err.
> + return -EBADMSG;
> + }
> + }
> +
> + *val = get_unaligned_be32(&priv->data[header_len]);
> +
> + return ret;
> +}
> +
> +static int adin1110_write_reg(struct adin1110_priv *priv, u16 reg, u32 val)
> +{
> + u32 header_len = ADIN1110_WR_HEADER_LEN;
> + u32 write_len = ADIN1110_REG_LEN;
> + __le16 __reg = cpu_to_le16(reg);
> +
> + priv->data[0] = ADIN1110_CD | ADIN1110_WRITE | FIELD_GET(GENMASK(12, 8), __reg);
> + priv->data[1] = FIELD_GET(GENMASK(7, 0), __reg);
> +
> + if (priv->append_crc) {
> + priv->data[2] = adin1110_crc_data(&priv->data[0], header_len);
> + header_len++;
> + }
> +
> + put_unaligned_be32(val, &priv->data[header_len]);
> + if (priv->append_crc) {
> + priv->data[header_len + write_len] = adin1110_crc_data(&priv->data[header_len],
> + write_len);
> + write_len++;
> + }
> +
> + return spi_write(priv->spidev, &priv->data[0], header_len + write_len);
> +}
> +
> +static int adin1110_set_bits(struct adin1110_priv *priv, u16 reg, unsigned long mask,
> + unsigned long val)
> +{
> + u32 write_val;
> + int ret;
> +
> + ret = adin1110_read_reg(priv, reg, &write_val);
> + if (ret < 0)
> + return ret;
> +
> + set_mask_bits(&write_val, mask, val);
> +
> + return adin1110_write_reg(priv, reg, write_val);
> +}
> +
> +static int adin1110_round_len(int len)
> +{
> + /* can read/write only mutiples of 4 bytes of payload */
> + len = ALIGN(len, 4);
> +
> + /* NOTE: ADIN1110_WR_HEADER_LEN should be used for write ops. */
> + if (len + ADIN1110_RD_HEADER_LEN > ADIN1110_MAX_BUFF)
> + return -EINVAL;
> +
> + return len;
> +}
> +
> +static int adin1110_read_fifo(struct adin1110_port_priv *port_priv)
> +{
> + struct adin1110_priv *priv = port_priv->priv;
> + u32 header_len = ADIN1110_RD_HEADER_LEN;
> + struct spi_transfer t[2] = {0};
> + u32 frame_size_no_fcs;
> + struct sk_buff *rxb;
> + u32 frame_size;
> + int round_len;
> + __le16 __reg;
> + int ret;
> +
> + if (!port_priv->nr) {
> + __reg = cpu_to_le16(ADIN1110_RX);
> + ret = adin1110_read_reg(priv, ADIN1110_RX_FSIZE, &frame_size);
> + } else {
> + __reg = cpu_to_le16(ADIN2111_RX_P2);
> + ret = adin1110_read_reg(priv, ADIN2111_RX_P2_FSIZE, &frame_size);
> + }
> +
> + if (ret < 0)
> + return ret;
> +
> + /* the read frame size includes the extra 2 bytes from the ADIN1110 frame header */
> + if (frame_size < ADIN1110_FRAME_HEADER_LEN + ADIN1110_FEC_LEN)
> + return ret;
> +
> + round_len = adin1110_round_len(frame_size);
> + if (round_len < 0)
> + return ret;
> +
> + frame_size_no_fcs = frame_size - ADIN1110_FRAME_HEADER_LEN - ADIN1110_FEC_LEN;
> +
> + rxb = netdev_alloc_skb(port_priv->netdev, frame_size_no_fcs);
> + if (!rxb)
> + return -ENOMEM;
> +
> + memset(priv->data, 0, round_len + ADIN1110_RD_HEADER_LEN);
> +
> + priv->data[0] = ADIN1110_CD | FIELD_GET(GENMASK(12, 8), __reg);
> + priv->data[1] = FIELD_GET(GENMASK(7, 0), __reg);
> + priv->data[2] = 0x00;
Shouldn't this already be initialized by memset?
> +
> + if (priv->append_crc) {
> + priv->data[2] = adin1110_crc_data(&priv->data[0], 2);
> + priv->data[3] = 0x00;
> + header_len++;
> + }
> +
> + t[0].tx_buf = &priv->data[0];
> + t[0].len = header_len;
> +
> + t[1].rx_buf = &priv->data[header_len];
> + t[1].len = round_len;
> +
> + ret = spi_sync_transfer(priv->spidev, t, 2);
> + if (ret) {
> + kfree_skb(rxb);
> + return ret;
> + }
> +
> + /* Already forwarded to the other port if it did not match any MAC Addresses. */
> + if (priv->forwarding)
> + rxb->offload_fwd_mark = 1;
> +
> + skb_put(rxb, frame_size_no_fcs);
> + skb_copy_to_linear_data(rxb, &priv->data[header_len + ADIN1110_FRAME_HEADER_LEN],
> + frame_size_no_fcs);
> +
> + rxb->protocol = eth_type_trans(rxb, port_priv->netdev);
> +
> + netif_rx(rxb);
> +
> + port_priv->rx_bytes += frame_size - ADIN1110_FRAME_HEADER_LEN;
> +
> + return 0;
> +}
> +
> +static int adin1110_write_fifo(struct adin1110_port_priv *port_priv, struct sk_buff *txb)
> +{
> + struct adin1110_priv *priv = port_priv->priv;
> + __le16 __reg = cpu_to_le16(ADIN1110_TX);
> + u32 header_len = ADIN1110_WR_HEADER_LEN;
> + __be16 frame_header;
> + int padding = 0;
> + int round_len;
> + int padded_len;
> + int ret;
> +
> + /* Pad frame to 64 byte length,
> + * MAC nor PHY will otherwise add the
> + * required padding.
> + * The FEC will be added by the MAC internally.
> + */
> + if (txb->len + ADIN1110_FEC_LEN < 64)
> + padding = 64 - (txb->len + ADIN1110_FEC_LEN);
> +
> + padded_len = txb->len + padding + ADIN1110_FRAME_HEADER_LEN;
> +
> + round_len = adin1110_round_len(padded_len);
> + if (round_len < 0)
> + return round_len;
> +
> + ret = adin1110_write_reg(priv, ADIN1110_TX_FSIZE, padded_len);
> + if (ret < 0)
> + return ret;
> +
> + memset(priv->data, 0, round_len + ADIN1110_WR_HEADER_LEN);
> +
> + priv->data[0] = ADIN1110_CD | ADIN1110_WRITE | FIELD_GET(GENMASK(12, 8), __reg);
> + priv->data[1] = FIELD_GET(GENMASK(7, 0), __reg);
> + if (priv->append_crc) {
> + priv->data[2] = adin1110_crc_data(&priv->data[0], 2);
> + header_len++;
> + }
> +
> + /* mention the port on which to send the frame in the frame header */
> + frame_header = cpu_to_be16(port_priv->nr);
> + memcpy(&priv->data[header_len], &frame_header, ADIN1110_FRAME_HEADER_LEN);
> +
> + memcpy(&priv->data[header_len + ADIN1110_FRAME_HEADER_LEN], txb->data, txb->len);
> +
> + ret = spi_write(priv->spidev, &priv->data[0], round_len + header_len);
> + if (ret < 0)
> + return ret;
> +
> + port_priv->tx_bytes += txb->len;
> +
> + return 0;
> +}
> +
> +static int adin1110_read_mdio_acc(struct adin1110_priv *priv)
> +{
> + u32 val;
> + int ret;
> +
> + ret = adin1110_read_reg(priv, ADIN1110_MDIOACC, &val);
> + if (ret < 0)
> + return 0;
> +
> + return val;
> +}
> +
> +static int adin1110_mdio_read(struct mii_bus *bus, int phy_id, int reg)
> +{
> + struct adin1110_priv *priv = bus->priv;
> + u32 val = 0;
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + val |= FIELD_PREP(ADIN1110_MDIO_OP, ADIN1110_MDIO_OP_RD);
> + val |= FIELD_PREP(ADIN1110_MDIO_ST, 0x1);
> + val |= FIELD_PREP(ADIN1110_MDIO_PRTAD, phy_id);
> + val |= FIELD_PREP(ADIN1110_MDIO_DEVAD, reg);
> +
> + /* write the clause 22 read command to the chip */
> + ret = adin1110_write_reg(priv, ADIN1110_MDIOACC, val);
> + if (ret < 0) {
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
> +
> + /* ADIN1110_MDIO_TRDONE BIT of the ADIN1110_MDIOACC
> + * register is set when the read is done.
> + * After the transaction is done, ADIN1110_MDIO_DATA
> + * bitfield of ADIN1110_MDIOACC register will contain
> + * the requested register value.
> + */
> + ret = readx_poll_timeout(adin1110_read_mdio_acc, priv, val, (val & ADIN1110_MDIO_TRDONE),
> + 10000, 30000);
> + mutex_unlock(&priv->lock);
> +
> + if (ret < 0)
> + return ret;
> +
> + return (val & ADIN1110_MDIO_DATA);
> +}
> +
> +static int adin1110_mdio_write(struct mii_bus *bus, int phy_id, int reg, u16 reg_val)
> +{
> + struct adin1110_priv *priv = bus->priv;
> + u32 val = 0;
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + val |= FIELD_PREP(ADIN1110_MDIO_OP, ADIN1110_MDIO_OP_WR);
> + val |= FIELD_PREP(ADIN1110_MDIO_ST, 0x1);
> + val |= FIELD_PREP(ADIN1110_MDIO_PRTAD, phy_id);
> + val |= FIELD_PREP(ADIN1110_MDIO_DEVAD, reg);
> + val |= FIELD_PREP(ADIN1110_MDIO_DATA, reg_val);
> +
> + /* write the clause 22 write command to the chip */
> + ret = adin1110_write_reg(priv, ADIN1110_MDIOACC, val);
> + if (ret < 0) {
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
> +
> + ret = readx_poll_timeout(adin1110_read_mdio_acc, priv, val, (val & ADIN1110_MDIO_TRDONE),
> + 10000, 30000);
> + mutex_unlock(&priv->lock);
> +
> + return ret;
> +}
> +
> +/* ADIN1110 MAC-PHY contains an ADIN1100 PHY.
> + * ADIN2111 MAC-PHY contains two ADIN1100 PHYs.
> + * By registering a new MDIO bus we allow the PAL to discover
> + * the encapsulated PHY and probe the ADIN1100 driver.
> + */
> +static int adin1110_register_mdiobus(struct adin1110_priv *priv, struct device *dev)
> +{
> + struct mii_bus *mii_bus;
> + int ret;
> +
> + mii_bus = devm_mdiobus_alloc(dev);
> + if (!mii_bus)
> + return -ENOMEM;
> +
> + snprintf(priv->mii_bus_name, MII_BUS_ID_SIZE, "%s-%u",
> + priv->cfg->name, priv->spidev->chip_select);
> +
> + mii_bus->name = priv->mii_bus_name;
> + mii_bus->read = adin1110_mdio_read;
> + mii_bus->write = adin1110_mdio_write;
> + mii_bus->priv = priv;
> + mii_bus->parent = dev;
> + mii_bus->phy_mask = ~((u32)GENMASK(2, 0));
> + snprintf(mii_bus->id, MII_BUS_ID_SIZE, "%s", dev_name(dev));
> +
> + ret = devm_mdiobus_register(dev, mii_bus);
> + if (ret)
> + return ret;
> +
> + priv->mii_bus = mii_bus;
> +
> + return 0;
> +}
> +
> +static bool adin1110_port_rx_ready(struct adin1110_port_priv *port_priv, u32 status)
> +{
> + if (!port_priv->nr)
> + return !!(status & ADIN1110_RX_RDY);
> + else
> + return !!(status & ADIN2111_P2_RX_RDY);
> +}
> +
> +static void adin1110_read_frames(struct adin1110_port_priv *port_priv)
> +{
> + struct adin1110_priv *priv = port_priv->priv;
> + u32 status1;
> + int ret;
> +
> + while (1) {
> + ret = adin1110_read_reg(priv, ADIN1110_STATUS1, &status1);
> + if (ret < 0)
> + return;
> +
> + if (!adin1110_port_rx_ready(port_priv, status1))
> + break;
> +
> + ret = adin1110_read_fifo(port_priv);
> + if (ret < 0)
> + return;
> + }
> +}
> +
> +static void adin1110_wake_queues(struct adin1110_priv *priv)
> +{
> + int i;
> +
> + for (i = 0; i < priv->cfg->ports_nr; i++)
> + netif_wake_queue(priv->ports[i]->netdev);
> +}
> +
> +static irqreturn_t adin1110_irq(int irq, void *p)
> +{
> + struct adin1110_priv *priv = p;
> + u32 status1;
> + u32 val;
> + int ret;
> + int i;
> +
> + mutex_lock(&priv->lock);
> +
> + adin1110_read_reg(priv, ADIN1110_STATUS1, &status1);
status1 would be uninitialized in error case
> +
> + if (priv->append_crc && (status1 & ADIN1110_SPI_ERR))
> + dev_warn(&priv->spidev->dev, "SPI CRC error on write.\n");
Same as above. You should try to avoid this at least with a rate limited
version of dev_warn.
...
> +static void adin1110_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *di)
> +{
> + strscpy(di->driver, "ADIN1110", sizeof(di->driver));
> + strscpy(di->version, "1.00", sizeof(di->version));
AFAIK this version assigment should be dropped
> + strscpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info));
> +}
> +
> +static const struct ethtool_ops adin1110_ethtool_ops = {
> + .get_drvinfo = adin1110_get_drvinfo,
> + .get_link = ethtool_op_get_link,
> + .get_link_ksettings = phy_ethtool_get_link_ksettings,
> + .set_link_ksettings = phy_ethtool_set_link_ksettings,
> +};
> +
> +static void adin1110_adjust_link(struct net_device *dev)
> +{
> + struct phy_device *phydev = dev->phydev;
> +
> + if (!phydev->link)
> + phy_print_status(phydev);
> +}
> +
> +/* PHY ID is stored in the MAC registers too, check spi connection by reading it */
> +static int adin1110_check_spi(struct adin1110_priv *priv)
> +{
> + int ret;
> + u32 val;
> +
> + ret = adin1110_read_reg(priv, ADIN1110_PHY_ID, &val);
> + if (ret < 0)
> + return ret;
> +
> + if (val != priv->cfg->phy_id_val) {
> + dev_err(&priv->spidev->dev, "PHY ID read: %x\n", val);
User usually doesn't look at the kernel sources. So printing the
expected value might be helpful in error case.
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static void adin1110_disconnect_phy(void *data)
> +{
> + phy_disconnect(data);
> +}
> +
> +static void adin1110_unregister_notifier(void *data)
> +{
> + unregister_netdevice_notifier(data);
> +}
> +
> +static int adin1110_hw_forwarding(struct adin1110_priv *priv, bool enable)
> +{
> + int mac_nr;
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + /* Configure MAC to forward unknown host to other port. */
> + ret = adin1110_set_bits(priv, ADIN1110_CONFIG2, ADIN2111_FWD_UNK2PORT,
> + enable ? ADIN2111_FWD_UNK2PORT : 0);
> + if (ret < 0) {
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
> +
> + /* Broadcast and multicast should also be forwarded to the other port */
> + for (mac_nr = 0; mac_nr <= ADIN_MAC_BROADCAST_ADDR_SLOT; mac_nr++) {
> + u32 offset = mac_nr * 2;
> + u32 port_rules;
> + u32 port_rules_mask;
> + u32 val;
> +
> + if (mac_nr == ADIN_MAC_ADDR_SLOT)
> + continue;
> +
> + port_rules_mask = ADIN1110_MAC_ADDR_APPLY2PORT | ADIN2111_MAC_ADDR_APPLY2PORT2;
> + port_rules = port_rules_mask;
> + port_rules_mask |= ADIN2111_MAC_ADDR_TO_OTHER_PORT;
> + if (enable)
> + port_rules |= ADIN2111_MAC_ADDR_TO_OTHER_PORT;
> +
> + /* tell MAC to forward this DA to host */
> + val = port_rules | ADIN1110_MAC_ADDR_TO_HOST;
> + ret = adin1110_set_bits(priv, ADIN1110_MAC_ADDR_FILTER_UPR + offset,
> + port_rules_mask, port_rules);
> + if (ret < 0) {
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
> + }
> +
> + ret = adin1110_set_bits(priv, ADIN1110_CONFIG2, ADIN2111_FWD_UNK2PORT,
> + ADIN2111_FWD_UNK2PORT);
> + if (ret < 0) {
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
> +
> + ret = adin1110_set_bits(priv, ADIN1110_CONFIG1, ADIN1110_CONFIG1_SYNC,
> + ADIN1110_CONFIG1_SYNC);
> +
> + mutex_unlock(&priv->lock);
> +
> + if (ret < 0)
> + return ret;
> +
> + priv->forwarding = enable;
> +
> + return ret;
> +}
> +
> +static int adin1110_port_bridge_join(struct adin1110_port_priv *port_priv,
> + struct net_device *bridge)
> +{
> + struct adin1110_priv *priv = port_priv->priv;
> + int ret = 0;
> +
> + /* Having the same port belong to multiple bridges is not supported */
> + if (port_priv->bridge && port_priv->bridge != bridge)
> + return -EOPNOTSUPP;
> +
> + port_priv->bridge = bridge;
> +
> + /* If other port joined same bridge, allow forwarding between ports */
> + if (priv->ports[0]->bridge == priv->ports[1]->bridge)
> + ret = adin1110_hw_forwarding(priv, true);
> +
> + return ret;
> +}
> +
> +static int adin1110_port_bridge_leave(struct adin1110_port_priv *port_priv,
> + struct net_device *bridge)
> +{
> + struct adin1110_priv *priv = port_priv->priv;
> + int ret = 0;
> +
> + if (priv->ports[0]->bridge == priv->ports[1]->bridge)
> + ret = adin1110_hw_forwarding(priv, false);
> +
> + port_priv->bridge = NULL;
> +
> + return ret;
> +}
> +
> +static int adin1110_netdevice_event(struct notifier_block *unused, unsigned long event, void *ptr)
> +{
> + struct net_device *dev = netdev_notifier_info_to_dev(ptr);
> + struct adin1110_port_priv *port_priv = netdev_priv(dev);
> + struct netdev_notifier_changeupper_info *info = ptr;
> + int ret = 0;
> +
> + switch (event) {
> + case NETDEV_CHANGEUPPER:
> + if (netif_is_bridge_master(info->upper_dev)) {
> + if (info->linking)
> + ret = adin1110_port_bridge_join(port_priv, info->upper_dev);
> + else
> + ret = adin1110_port_bridge_leave(port_priv, info->upper_dev);
> + }
> + break;
> + default:
> + break;
> + }
> +
> + return notifier_from_errno(ret);
> +}
> +
> +struct notifier_block adin1110_netdevice_nb __read_mostly = {
> + .notifier_call = adin1110_netdevice_event,
> +};
> +
> +static int adin1110_probe_netdevs(struct adin1110_priv *priv)
> +{
> + struct device *dev = &priv->spidev->dev;
> + struct adin1110_port_priv *port_priv;
> + struct net_device *netdev;
> + int ret;
> + int i;
> +
> + for (i = 0; i < priv->cfg->ports_nr; i++) {
> + netdev = devm_alloc_etherdev(dev, sizeof(*port_priv));
> + if (!netdev)
> + return -ENOMEM;
> +
> + port_priv = netdev_priv(netdev);
> + port_priv->netdev = netdev;
> + port_priv->priv = priv;
> + port_priv->cfg = priv->cfg;
> + port_priv->nr = i;
> + priv->ports[i] = port_priv;
> + SET_NETDEV_DEV(netdev, dev);
> +
> + ret = device_get_ethdev_address(dev, netdev);
> + if (ret < 0)
> + return ret;
> +
> + netdev->irq = priv->spidev->irq;
> + INIT_WORK(&port_priv->tx_work, adin1110_tx_work);
> + INIT_WORK(&port_priv->rx_mode_work, adin1110_rx_mode_work);
> + skb_queue_head_init(&port_priv->txq);
> +
> + netif_carrier_off(netdev);
> +
> + netdev->if_port = IF_PORT_10BASET;
> + netdev->netdev_ops = &adin1110_netdev_ops;
> + netdev->ethtool_ops = &adin1110_ethtool_ops;
> + netdev->priv_flags |= IFF_UNICAST_FLT;
> + netdev->features |= NETIF_F_NETNS_LOCAL;
> +
> + ret = devm_register_netdev(dev, netdev);
> + if (ret < 0) {
> + dev_err(dev, "failed to register network device\n");
> + return ret;
> + }
> +
> + port_priv->phydev = get_phy_device(priv->mii_bus, i + 1, false);
> + if (!port_priv->phydev) {
> + netdev_err(netdev, "Could not find PHY with device address: %d.\n", i);
> + return -ENODEV;
> + }
> +
> + port_priv->phydev = phy_connect(netdev, phydev_name(port_priv->phydev),
> + adin1110_adjust_link, PHY_INTERFACE_MODE_MII);
> + if (IS_ERR(port_priv->phydev)) {
> + netdev_err(netdev, "Could not connect PHY with device address: %d.\n", i);
> + return PTR_ERR(port_priv->phydev);
> + }
> +
> + ret = devm_add_action_or_reset(dev, adin1110_disconnect_phy, port_priv->phydev);
> + if (ret < 0)
> + return ret;
> + }
> +
> + /* ADIN1110 INT_N pin will be used to signal the host */
> + ret = devm_request_threaded_irq(dev, priv->spidev->irq, NULL, adin1110_irq,
> + IRQF_TRIGGER_LOW | IRQF_ONESHOT, dev_name(dev), priv);
> + if (ret < 0)
> + return ret;
> +
> + if (priv->cfg->id == ADIN2111_MAC) {
> + ret = register_netdevice_notifier(&adin1110_netdevice_nb);
> + if (ret < 0)
> + return ret;
> +
> + ret = devm_add_action_or_reset(dev, adin1110_unregister_notifier,
> + &adin1110_netdevice_nb);
> + if (ret < 0)
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int adin1110_probe(struct spi_device *spi)
> +{
> + const struct spi_device_id *dev_id = spi_get_device_id(spi);
> + struct device *dev = &spi->dev;
> + struct adin1110_priv *priv;
> + int ret;
> +
> + priv = devm_kzalloc(dev, sizeof(struct adin1110_priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + priv->spidev = spi;
> + priv->cfg = &adin1110_cfgs[dev_id->driver_data];
> + spi->bits_per_word = 8;
SPI mode ?
> +
> + mutex_init(&priv->lock);
> + spin_lock_init(&priv->state_lock);
> +
> + /* use of CRC on control and data transactions is pin dependent */
> + priv->append_crc = device_property_read_bool(dev, "adi,spi-crc");
> + if (priv->append_crc)
> + crc8_populate_msb(adin1110_crc_table, 0x7);
> +
> + ret = adin1110_check_spi(priv);
> + if (ret < 0) {
> + dev_err(dev, "SPI read failed: %d\n", ret);
This error message sounds a bit to general, it's the initial check for
the chip via SPI.
> + return ret;
> + }
> +
> + ret = adin1110_write_reg(priv, ADIN1110_RESET, ADIN1110_SWRESET);
> + if (ret < 0)
> + return ret;
> +
> + ret = adin1110_register_mdiobus(priv, dev);
> + if (ret < 0) {
> + dev_err(dev, "Could not register MDIO bus %d\n", ret);
> + return ret;
> + }
> +
> + return adin1110_probe_netdevs(priv);
> +}
> +
> +static const struct of_device_id adin1110_match_table[] = {
> + { .compatible = "adi,adin1110" },
> + { .compatible = "adi,adin2111" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, adin1110_match_table);
> +
> +static const struct spi_device_id adin1110_spi_id[] = {
> + { .name = "adin1110", .driver_data = ADIN1110_MAC },
> + { .name = "adin2111", .driver_data = ADIN2111_MAC },
> + { }
> +};
> +
> +static struct spi_driver adin1110_driver = {
> + .driver = {
> + .name = "adin1110",
> + .of_match_table = adin1110_match_table,
> + },
> + .probe = adin1110_probe,
> + .id_table = adin1110_spi_id,
> +};
> +module_spi_driver(adin1110_driver);
> +
> +MODULE_DESCRIPTION("ADIN1110 Network driver");
> +MODULE_AUTHOR("Alexandru Tachici <[email protected]>");
> +MODULE_LICENSE("Dual BSD/GPL");