Correct the following warnings by adding the required supplies (AVDD, DVDD)
for the ov5640 node.
arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'AVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'DVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
Signed-off-by: Alain Volmat <[email protected]>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index ba8e9d9a42fa..f27d6dcb6651 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -185,7 +185,9 @@ ov5640: camera@3c {
reg = <0x3c>;
clocks = <&clk_ext_camera>;
clock-names = "xclk";
+ AVDD-supply = <&v2v8>;
DOVDD-supply = <&v2v8>;
+ DVDD-supply = <&v2v8>;
powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
rotation = <180>;
--
2.25.1
Hi Alain
On 6/1/23 08:52, Alain Volmat wrote:
> Correct the following warnings by adding the required supplies (AVDD, DVDD)
> for the ov5640 node.
>
> arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'AVDD-supply' is a required property
> From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
> arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'DVDD-supply' is a required property
> From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
>
> Signed-off-by: Alain Volmat <[email protected]>
> ---
> arch/arm/boot/dts/stm32mp157c-ev1.dts | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
> index ba8e9d9a42fa..f27d6dcb6651 100644
> --- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
> +++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
> @@ -185,7 +185,9 @@ ov5640: camera@3c {
> reg = <0x3c>;
> clocks = <&clk_ext_camera>;
> clock-names = "xclk";
> + AVDD-supply = <&v2v8>;
> DOVDD-supply = <&v2v8>;
> + DVDD-supply = <&v2v8>;
> powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
> reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
> rotation = <180>;
Applied on stm32-next.
Thanks.
Alex